SN74LVCZ16244ADL

SN74LVCZ16244A 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES277D – JUNE 1999 – REVISED SEPTEMBER 2002 D D D D D D D D DGG, DGV, OR DL PACKAGE (TOP VIEW) Member of the Texas Instruments Widebus  Family Operates From 2.7 V to 3.6 V Inputs Accept Voltages to 5.5 V Max tpd of 4.1 ns at 3.3 V Ioff and Power-Up 3-State Support Hot Insertion Supports Mixed-Mode Signal Operation on All Ports (5-V Input/Output Voltage With 3.3-V VCC) Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-A) – 1000-V Charged-Device Model (C101) 1OE 1Y1 1Y2 GND 1Y3 1Y4 VCC 2Y1 2Y2 GND 2Y3 2Y4 3Y1 3Y2 GND 3Y3 3Y4 VCC 4Y1 4Y2 GND 4Y3 4Y4 4OE description/ordering information This 16-bit buffer/driver is designed for 2.7-V to 3.6-V VCC operation. The SN74LVCZ16244A is designed specifically to improve the performance and density of 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters. The device can be used as four 4-bit buffers, two 8-bit buffers, or one 16-bit buffer. It provides true outputs. 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 2OE 1A1 1A2 GND 1A3 1A4 VCC 2A1 2A2 GND 2A3 2A4 3A1 3A2 GND 3A3 3A4 VCC 4A1 4A2 GND 4A3 4A4 3OE Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of these devices as translators in a mixed 3.3-V/5-V system environment. During power up or power down when VCC is between 0 and 1.5 V, the device is in the high-impedance state. However, to ensure the high-impedance state above 1.5 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION PACKAGE† ORDERABLE PART NUMBER Tube SN74LVCZ16244ADL Tape and reel SN74LVCZ16244ADLR TSSOP – DGG Tape and reel SN74LVCZ16244ADGGR LVCZ16244A TVSOP – DGV Tape and reel SN74LVCZ16244ADGVR CW244A TA SSOP – DL –40°C 40°C to 85°C TOP-SIDE MARKING LVCZ16244A † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments. Copyright  2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74LVCZ16244A 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES277D – JUNE 1999 – REVISED SEPTEMBER 2002 description/ordering information (continued) This device is fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down (VCC = 0 V). The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict. FUNCTION TABLE (each 4-bit buffer) INPUTS OE A OUTPUT Y L H H L L L H X Z logic diagram (positive logic) 1OE 1A1 1A2 1A3 1A4 2OE 2A1 2A2 2A3 2A4 2 1 3OE 47 2 46 3 44 5 43 6 1Y1 3A1 1Y2 3A2 1Y3 3A3 1Y4 3A4 48 4OE 41 8 40 9 38 11 37 12 2Y1 4A1 2Y2 4A2 2Y3 4A3 2Y4 4A4 POST OFFICE BOX 655303 25 36 13 35 14 33 16 32 17 3Y1 3Y2 3Y3 3Y4 24 30 19 29 20 27 22 26 23 • DALLAS, TEXAS 75265 4Y1 4Y2 4Y3 4Y4 SN74LVCZ16244A 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES277D – JUNE 1999 – REVISED SEPTEMBER 2002 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6.5 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6.5 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6.5 V Voltage range applied to any output in the high or low state, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through each VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA Package thermal impedance, θJA (see Note 3): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The value of VCC is provided in the recommended operating conditions table. 3. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 4) MIN MAX 2.7 3.6 VCC VIH Supply voltage VIL VI Low-level input voltage VO Output voltage IOH High level output current High-level VCC = 2.7 V VCC = 3 V –12 IOL Low level output current Low-level VCC = 2.7 V VCC = 3 V 12 ∆t/∆v Input transition rise or fall rate ∆t/∆VCC TA Power-up ramp rate 150 Operating free-air temperature –40 High-level input voltage VCC = 2.7 V to 3.6 V VCC = 2.7 V to 3.6 V 2 UNIT V V 0.8 V 0 5.5 V High or low state 0 3-state 0 VCC 5.5 V Input voltage –24 24 10 mA mA ns/V µs/V 85 °C NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN74LVCZ16244A 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES277D – JUNE 1999 – REVISED SEPTEMBER 2002 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VCC 2.7 V to 3.6 V IOH = –100 µA VOH 2.7 V IOH = –12 12 mA IOH = –24 mA IOL = 100 µA MIN TYP† MAX VCC–0.2 2.2 3V 2.4 3V 2.2 UNIT V 2.7 V to 3.6 V 0.2 VOL IOL = 12 mA IOL = 24 mA 2.7 V 0.4 3V 0.55 II Ioff VI = 0 to 5.5 V VI or VO = 5.5 V 3.6 V ±5 µA 0 ±5 µA IOZ VO = 0 to 5.5 V 3.6 V ±5 µA IOZPU VO = 0.5 V to 2.5 V, OE = don’t care 0 to 1.5 V ±5 µA IOZPD VO = 0.5 V to 2.5 V, OE = don’t care 1.5 V to 0 ±5 µA ICC VI = VCC or GND 3.6 V ≤ VI ≤ 5.5 V‡ IO = 0 ∆ICC Ci One input at VCC – 0.6 V, Other inputs at VCC or GND 100 2.7 V to 3.6 V VI = VCC or GND VO = VCC or GND Co 100 36V 3.6 100 V µA µA 3.3 V 4.5 pF 3.3 V 6 pF † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ This applies in the disabled state only. switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) tpd A ten tdis PARAMETER VCC = 2.7 V VCC = 3.3 V ± 0.3 V UNIT MIN MAX MIN MAX Y 1.1 4.4 1.1 4.1 ns OE Y 1 4.9 1 4.6 ns OE Y 1.8 6.1 1.8 5.8 ns switching characteristics over recommended operating free-air temperature range, CL = 30 pF (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) tpd A Y ten OE tdis OE PARAMETER VCC = 2.7 V VCC = 3.3 V ± 0.3 V UNIT MIN MAX MIN MAX 1 4.3 1 4 ns Y 1 4.7 1 4.4 ns Y 1.7 5.6 1.7 5.3 ns operating characteristics, TA = 25°C TEST CONDITIONS PARAMETER Cpd 4 Outputs enabled Power dissipation capacitance per buffer/driver POST OFFICE BOX 655303 Outputs disabled • DALLAS, TEXAS 75265 VCC = 3.3 V TYP UNIT 32 f = 10 MHz 5.5 pF SN74LVCZ16244A 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCES277D – JUNE 1999 – REVISED SEPTEMBER 2002 PARAMETER MEASUREMENT INFORMATION VCC = 2.7 V AND 3.3 V ± 0.3 V 2 × VCC S1 500 Ω From Output Under Test Open GND CL = 30 pF or 50 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND LOAD CIRCUIT tw VCC Timing Input VCC/2 VCC/2 VCC/2 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC/2 VCC/2 0V tPLH Output Control (low-level enabling) tPLZ VCC VCC/2 tPZH VOH VCC/2 VOL VCC/2 0V Output Waveform 1 S1 at 2 × VCC (see Note B) tPHL VCC/2 VCC VCC/2 tPZL VCC Input VOLTAGE WAVEFORMS PULSE DURATION th VCC Data Input VCC/2 0V 0V tsu Output VCC VCC/2 Input Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ VCC/2 VOH VOH – 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74LVCZ16244ADGGR ACTIVE TSSOP DGG 48 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LVCZ16244A SN74LVCZ16244ADGVR ACTIVE TVSOP DGV 48 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 CW244A SN74LVCZ16244ADLR ACTIVE SSOP DL 48 1000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LVCZ16244A (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of