SN74LVTH16244ADLR

SN54LVTH16244A, SN74LVTH16244A www.ti.com SCBS142U – MAY 1992 – REVISED OCTOBER 2013 3.3-V ABT 16-Bit Buffers/Drivers With 3-State Outputs Check for Samples: SN54LVTH16244A, SN74LVTH16244A FEATURES DESCRIPTION • The 'LVTH16244A devices are 16-bit buffers and line drivers designed for low-voltage (3.3-V) VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. These devices can be used as four 4-bit buffers, two 8-bit buffers, or one 16-bit buffer. These devices provide true outputs and symmetrical active-low output-enable (OE) inputs. 1 2 • • • • • • • • Members of the Texas Instruments Widebus™ Family State-of-the-Art Advanced BiCMOS Technology (ABT) Design for 3.3-V Operation and Low Static-Power Dissipation Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V VCC) Support Unregulated Battery Operation Down to 2.7 V Typical VOLP (Output Ground Bounce) VCC. The package thermal impedance is calculated in accordance with JESD 51-7. RECOMMENDED OPERATING CONDITIONS (1) SN54LVTH16244A SN74LVTH16244A MIN MAX MIN MAX 2.7 3.6 2.7 3.6 UNIT VCC Supply voltage VIH High-level input voltage VIL Low-level input voltage 0.8 0.8 VI Input voltage 5.5 5.5 V IOH High-level output current –25 –32 mA IOL Low-level output current 48 64 mA Δt/Δv Input transition rise or fall rate 10 10 ns/V Δt/ΔVCC Power-up ramp rate 200 TA Operating free-air temperature –55 (1) 2 V 2 Outputs enabled V μs/V 200 125 –40 V 125 °C All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. Copyright © 1992–2013, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: SN54LVTH16244A SN74LVTH16244A 5 SN54LVTH16244A, SN74LVTH16244A SCBS142U – MAY 1992 – REVISED OCTOBER 2013 www.ti.com ELECTRICAL CHARACTERISTICS over recommended operating free-air temperature range (unless otherwise noted) (1) PARAMETER TEST CONDITIONS MIN TYP VIK VOH VCC = 2.7 V, II = –18 mA VCC = 2.7 V to 3.6 V, IOL = –100 μA VCC = 2.7 V, IOH = –8 mA IOH = –24 mA VCC = 3 V MAX MIN TYP –1.2 VCC – 0.2 VOL VCC = 3 V Data inputs VCC – 0.2 Ioff II(hold) Data inputs 2.4 V 2.4 V 2 2 0.2 0.2 0.2 IOL = 24 mA 0.5 0.5 0.5 IOL = 16 mA 0.4 0.4 0.4 IOL = 32 mA 0.5 0.5 0.5 IOL = 48 mA 0.55 0.55 0.55 10 10 VCC = 3.6 V, VI = VCC or GND ±1 VI = VCC VI = 2 V ±1 1 –5 ±100 –5 μA ±100 75 75 75 –75 –75 –75 500 –750 500 –750 VCC = 3.6 V , VI = 0 to 3.6 V IOZH VCC = 3.6 V, VO = 3 V IOZL VCC = 3.6 V, VO = 0.5 V IOZPU VCC = 0 to 1.5 V, VO = 0.5 V to 3 V, OE = don't care ±100 ( IOZPD VCC = 1.5 V to 0, VO = 0.5 V to 3 V, OE = don't care ±100 ( ICC VCC = 3.6 V, IO = 0, VI = VCC or GND 5 5 5 μA –5 –5 μA 3) Outputs low Outputs disabled μA –5 3) Outputs high V μA 1 –5 VI or VO = 0 to 4.5 V VI = 0.8 V ±1 1 VI = 0 (2) –1.2 IOL = 100 μA 50 VCC = 3 V MAX 2 VI = 5.5 V VCC = 0, UNIT VCC – 0.2 2.4 VCC = 0 or 3.6 V, VCC = 3.6 V MIN TYP –1.2 IOL = 64 mA II MAX IOH = –32 mA VCC = 2.7 V Control inputs Recommended –40°C to 125C SN74LVTH16244A –40°C to 85°C SN74LVTH16244A SN54LVTH16244A ±100 ±100 μA ±100 ±100 μA 0.19 0.19 5 5 0.19 5 0.19 0.19 0.19 0.2 0.2 0.2 mA ΔICC (4) VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND Ci VI = 3 V or 0 V 4 4 4 pF Co VO = 3 V or 0 V 9 9 9 pF (1) (2) (3) (4) 6 mA All typical values are at VCC = 3.3 V, TA = 25°C. This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another. On products compliant to MIL-PRF-38535, this parameter does not apply. This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND. Submit Documentation Feedback Copyright © 1992–2013, Texas Instruments Incorporated Product Folder Links: SN54LVTH16244A SN74LVTH16244A SN54LVTH16244A, SN74LVTH16244A www.ti.com SCBS142U – MAY 1992 – REVISED OCTOBER 2013 SWITCHING CHARACTERISTICS over recommended operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) (1) PARAMETER tPLH tPHL tPZH tPZL tPHZ tPLZ (1) FROM (INPUT) TO (OUTPUT) A Y OE Y OE Y VCC = 3.3 V ± 0.3 V VCC = 2.7 V MIN Recommended –40°C to 125C SN74LVTH16244A –40°C to 85°C SN74LVTH16244A SN54LVTH16244A MAX VCC = 3.3 V ± 0.3 V MIN TYP VCC = 2.7 V MAX MIN MAX UNIT VCC = 3.3 V ± 0.3 V MIN TYP VCC = 2.7 V MIN MAX 1.1 4.4 4.6 1.2 2.3 3.2 3.7 1.2 2.3 MAX 4.4 4.6 1.1 3.6 3.9 1.2 2 3.2 3.7 1.2 2 3.6 3.9 1.1 4.6 5.4 1.2 2.6 4 5 1.2 2.6 4.6 5.4 1.1 5.4 6.2 1.2 2.7 4 5 1.2 2.7 5.4 6.2 1.6 5.7 6.2 2.2 3.3 4.5 5 2.2 3.3 5.7 6.2 1.2 5 4.7 2 3.1 4.2 4.4 2 3.1 5 4.7 tsk(LH) 0.5 0.5 tsk(HL) 0.5 0.5 MIN MAX ns ns ns ns All typical values are at VCC = 3.3 V, TA = 25°C. Copyright © 1992–2013, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: SN54LVTH16244A SN74LVTH16244A 7 SN54LVTH16244A, SN74LVTH16244A SCBS142U – MAY 1992 – REVISED OCTOBER 2013 www.ti.com PARAMETER MEASUREMENT INFORMATION 6V 500 Ω From Output Under Test S1 Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 6V GND 2.7 V LOAD CIRCUIT Timing Input 1.5 V 0V tw tsu 2.7 V Input 1.5 V th 2.7 V 1.5 V Data Input 1.5 V 1.5 V 0V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION 2.7 V Input 1.5 V 1.5 V 0V tPHL tPLH VOH Output 1.5 V 1.5 V VOL 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 1.5 V 0V tPLZ tPZL 3V 1.5 V Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ tPZH VOH Output Output Waveform 1 S1 at 6 V (see Note B) tPLH tPHL 2.7 V Output Control 1.5 V VOH − 0.3 V VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time, with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 8 Submit Documentation Feedback Copyright © 1992–2013, Texas Instruments Incorporated Product Folder Links: SN54LVTH16244A SN74LVTH16244A SN54LVTH16244A, SN74LVTH16244A www.ti.com SCBS142U – MAY 1992 – REVISED OCTOBER 2013 REVISION HISTORY Changes from Revision T (November 2006) to Revision U Page • Updated document to new TI data sheet format - no specification changes. ...................................................................... 1 • Removed ordering information. ............................................................................................................................................ 1 • Updated operating temperature range. ................................................................................................................................. 5 Copyright © 1992–2013, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: SN54LVTH16244A SN74LVTH16244A 9 PACKAGE OPTION ADDENDUM www.ti.com 10-Jun-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) 5962-9668501QXA ACTIVE CFP WD 48 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9668501QX A SNJ54LVTH16244 AWD 5962-9668501VXA ACTIVE CFP WD 48 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9668501VX A SNV54LVTH16244 AWD 74LVTH16244ADGGRE4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 LVTH16244A 74LVTH16244ADGGRG4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 LVTH16244A 74LVTH16244ADLRG4 ACTIVE SSOP DL 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 LVTH16244A SN74LVTH16244ADGGR ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 LVTH16244A SN74LVTH16244ADGVR ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 LL244A SN74LVTH16244ADL ACTIVE SSOP DL 48 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 LVTH16244A SN74LVTH16244ADLG4 ACTIVE SSOP DL 48 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 LVTH16244A SN74LVTH16244ADLR ACTIVE SSOP DL 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 LVTH16244A SN74LVTH16244AGQLR OBSOLETE BGA MICROSTAR JUNIOR GQL 56 TBD Call TI Call TI -40 to 85 SN74LVTH16244AGRDR OBSOLETE BGA MICROSTAR JUNIOR GRD 54 TBD Call TI Call TI -40 to 85 SN74LVTH16244AZQLR ACTIVE BGA MICROSTAR JUNIOR ZQL 56 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 1000 Addendum-Page 1 LL244A Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 10-Jun-2014 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) SN74LVTH16244AZRDR ACTIVE BGA MICROSTAR JUNIOR ZRD 54 1000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 LL244A SNJ54LVTH16244AWD ACTIVE CFP WD 48 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9668501QX A SNJ54LVTH16244 AWD (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com 10-Jun-2014 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN54LVTH16244A, SN54LVTH16244A-SP, SN74LVTH16244A : • Catalog: SN74LVTH16244A, SN54LVTH16244A • Enhanced Product: SN74LVTH16244A-EP, SN74LVTH16244A-EP • Military: SN54LVTH16244A • Space: SN54LVTH16244A-SP NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Enhanced Product - Supports Defense, Aerospace and Medical Applications • Military - QML certified for Military and Defense Applications • Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 8.6 15.8 1.8 12.0 24.0 Q1 SN74LVTH16244ADGGR TSSOP DGG 48 2000 330.0 24.4 SN74LVTH16244ADGVR TVSOP DGV 48 2000 330.0 16.4 7.1 10.2 1.6 12.0 16.0 Q1 DL 48 1000 330.0 32.4 11.35 16.2 3.1 16.0 32.0 Q1 SN74LVTH16244AZQLR BGA MI CROSTA R JUNI OR ZQL 56 1000 330.0 16.4 4.8 7.3 1.5 8.0 16.0 Q1 SN74LVTH16244AZRDR BGA MI CROSTA R JUNI OR ZRD 54 1000 330.0 16.4 5.8 8.3 1.55 8.0 16.0 Q1 SN74LVTH16244ADLR SSOP Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74LVTH16244ADGGR TSSOP DGG 48 2000 367.0 367.0 45.0 SN74LVTH16244ADGVR TVSOP DGV 48 2000 367.0 367.0 38.0 SN74LVTH16244ADLR SSOP DL 48 1000 367.0 367.0 55.0 SN74LVTH16244AZQLR BGA MICROSTAR JUNIOR ZQL 56 1000 336.6 336.6 28.6 SN74LVTH16244AZRDR BGA MICROSTAR JUNIOR ZRD 54 1000 336.6 336.6 28.6 Pack Materials-Page 2 MECHANICAL DATA MCFP010B – JANUARY 1995 – REVISED NOVEMBER 1997 WD (R-GDFP-F**) CERAMIC DUAL FLATPACK 48 LEADS SHOWN 0.120 (3,05) 0.075 (1,91) 0.009 (0,23) 0.004 (0,10) 1.130 (28,70) 0.870 (22,10) 0.370 (9,40) 0.250 (6,35) 0.390 (9,91) 0.370 (9,40) 0.370 (9,40) 0.250 (6,35) 48 1 0.025 (0,635) A 0.014 (0,36) 0.008 (0,20) 25 24 NO. OF LEADS** 48 56 A MAX 0.640 (16,26) 0.740 (18,80) A MIN 0.610 (15,49) 0.710 (18,03) 4040176 / D 10/97 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only Falls within MIL STD 1835: GDFP1-F48 and JEDEC MO -146AA GDFP1-F56 and JEDEC MO -146AB POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0°–
8° 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins – MO-153 14/16/20/56 Pins – MO-194 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS003D – JANUARY 1995 – REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated