SN74LVTH162541DGGR

SN54LVTH162541,, SN74LVTH162541 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS www.ti.com SCBS690F – MAY 1997 – REVISED NOVEMBER 2006 FEATURES • • • • • • • • • • • • • Members of the Texas Instruments Widebus™ Family State-of-the-Art Advanced BiCMOS Technology (ABT) Design for 3.3-V Operation and Low Static-Power Dissipation Output Ports Have Equivalent 22-Ω Series Resistors, So No External Resistors Are Required Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V VCC) Support Unregulated Battery Operation Down to 2.7 V Typical VOLP (Output Ground Bounce) VCC. The package thermal impedance is calculated in accordance with JESD 51. Recommended Operating Conditions (1) SN54LVTH162541 MAX MIN MAX 2.7 3.6 2.7 3.6 UNIT VCC Supply voltage VIH High-level input voltage VIL Low-level input voltage VI Input voltage 5.5 5.5 V IOH High-level output current –12 –12 mA IOL Low-level output current 12 12 mA ∆t/∆v Input transition rise or fall rate ∆t/∆VCC Power-up ramp rate 200 TA Operating free-air temperature –55 (1) 4 SN74LVTH162541 MIN 2 2 0.8 Outputs enabled V 0.8 10 10 –40 V ns/V µs/V 200 125 V 85 °C All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. Submit Documentation Feedback SN54LVTH162541,, SN74LVTH162541 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS www.ti.com SCBS690F – MAY 1997 – REVISED NOVEMBER 2006 Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS SN54LVTH162541 MIN TYP (1) SN74LVTH162541 MAX MIN TYP (1) VIK VCC = 2.7 V, II = –18 mA VOH VCC = 3 V, IOH = –12 mA VOL VCC = 3 V, IOL = 12 mA 0.8 0.8 VCC = 0 or 3.6 V, VI = 5.5 V 10 10 VCC = 3.6 V, VI = VCC or GND ±1 ±1 1 1 –5 –5 Control inputs II Data inputs Ioff VCC = 3.6 V VCC = 0, VI = 0 VI = 2 V V, (2) 75 –75 75 V µA µA µA 500 –750 5 5 µA –5 –5 µA ±100 (3) ±100 µA VCC = 1.5 V to 0, VO = 0.5 V to 3 V, OE = don't care ±100 (3) ±100 µA Outputs high 0.19 0.19 5 5 0.19 0.19 0.2 0.2 VCC = 3.6 V, VO = 3 V IOZL VCC = 3.6 V, VO = 0.5 V IOZPU VCC = 0 to 1.5 V, VO = 0.5 V to 3 V, OE = don't care IOZPD ICC VCC = 3.6 V, IO = 0, VI = VCC or GND ∆ICC ±100 75 V V VI = 0 to 3.6 V IOZH (4) 2 VI = VCC VI = 0.8 V Data inputs VCC = 3.6 2 UNIT –1.2 VI or VO = 0 to 4.5 V VCC = 3 V II(hold) –1.2 MAX Outputs low Outputs disabled VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND mA mA Ci VI = 3 V or 0 4 4 pF Co VO = 3 V or 0 9 9 pF (1) (2) (3) (4) All typical values are at VCC = 3.3 V, TA = 25°C. This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another. On products compliant to MIL-PRF-38535, this parameter is not production tested. This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND. Submit Documentation Feedback 5 SN54LVTH162541,, SN74LVTH162541 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS www.ti.com SCBS690F – MAY 1997 – REVISED NOVEMBER 2006 Switching Characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) SN54LVTH162541 PARAMETER VCC = 3.3 V ± 0.3 V SN74LVTH162541 VCC = 2.7 V VCC = 3.3 V ± 0.3 V VCC = 2.7 V MIN TYP (1) MAX 4.3 4.9 1.2 2.9 4.1 4.7 1.1 4.3 4.9 1.2 2.4 4.1 4.7 1.4 5.3 6.3 1.5 3.2 5 6.1 1.4 5.1 5.8 1.5 3.3 4.8 5.5 2.1 6.1 6.4 2.2 4.3 5.9 6.2 2.1 5.7 5.9 2.2 4 5.4 5.5 tsk(LH) 0.5 0.5 tsk(HL) 0.5 0.5 tPHL tPZH tPZL tPHZ tPLZ 6 TO (OUTPUT) MAX tPLH (1) FROM (INPUT) A Y OE Y OE Y MIN MAX 1.1 MIN All typical values are at VCC = 3.3 V, TA = 25°C. Submit Documentation Feedback MIN UNIT MAX ns ns ns ns SN54LVTH162541,, SN74LVTH162541 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS www.ti.com SCBS690F – MAY 1997 – REVISED NOVEMBER 2006 PARAMETER MEASUREMENT INFORMATION From Output Under Test 6V Open S1 500 Ω GND CL = 50 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 6V GND 2.7 V LOAD CIRCUIT 1.5 V Timing Input 0V tw tsu th 2.7 V 1.5 V Input 1.5 V 2.7 V 1.5 V Data Input 1.5 V 0V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION 2.7 V Input 1.5 V 1.5 V 0V tPLH tPHL VOH 1.5 V Output 1.5 V VOL tPHL Output Waveform 1 S1 at 6 V (see Note B) 1.5 V 1.5 V 1.5 V 0V tPZL tPLZ 3V 1.5 V tPZH tPLH VOH Output 2.7 V Output Control 1.5 V VOL Output Waveform 2 S1 at GND (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS VOL + 0.3 V VOL tPHZ 1.5 V VOH − 0.3 V VOH ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time, with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms Submit Documentation Feedback 7 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) (3) Device Marking (4/5) (6) SN74LVTH162541DGGR ACTIVE TSSOP DGG 48 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LVTH162541 SN74LVTH162541DL ACTIVE SSOP DL 48 25 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LVTH162541 SN74LVTH162541DLR ACTIVE SSOP DL 48 1000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LVTH162541 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of