SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
DIGITAL TV TUNER IC
FEATURES
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Integrated Mixer/Oscillator/PLL and IF GCA
VHF-L, VHF-H, UHF 3-Band Local Oscillator
RF AGC Detector Circuit
I2C Bus Protocol
Bidirectional Data Transmission
High-Voltage Tuning Voltage Output
Four NPN-Type Band Switch Drivers
One Auxiliary Port/5-Level ADC
Crystal Oscillator Output
Programmable Reference Divider Ratio
(24/28/32/64/80/128)
IF GCA Enable/Disable Control
Selectable digital IFOUT and Analog IFOUT
Standby Mode
5-V Power Supply
44-Pin Thin Shrink Small-Outline Package
(TSSOP)
APPLICATIONS
•
•
•
Digital TVs
Digital CATVs
Set-Top Boxes
DBT PACKAGE
(TOP VIEW)
VLO OSC B
1
44
VLO OSC C
VHI OSC B
VHI OSC C
UHF OSC B1
UHF OSC C1
UHF OSC C2
UHF OSC B2
OSC GND
CP
VTU
IF GND
AIF OUT
DIF OUT1
DIF OUT2
2
43
3
42
4
41
5
40
6
39
7
38
8
37
9
36
10
35
11
34
12
33
13
32
14
31
15
30
IFGCA CTRL
VCC
IF GCA IN1
IF GCA IN2
IF GCA GND
IF GCA OUT2
IF GCA OUT1
16
29
17
28
18
27
19
26
20
25
21
24
22
23
BS4
UHF RF IN1
UHF RF IN2
VHI RF IN
VLO RF IN
RF GND
MIX OUT2
MIX OUT1
IF IN
RF AGC OUT
RF AGC BUF
BS3
BS2
BS1
SDA
SCL
AS
BUS GND
P5/ADC
XTAL OUT
XTAL2
XTAL1
DESCRIPTION
The SN761640 is a low-phase-noise synthesized tuner IC designed for digital TV tuning systems. The circuit
consists of a PLL synthesizer, three-band local oscillator and mixer, RF AGC detector circuit, and IF
gain-controlled amplifier. The SN761640 is available in a small-outline package.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008, Texas Instruments Incorporated
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
VHF-L
Oscillator
VHF-H
Oscillator
IF IN
MIX OUT2
MIX OUT1
UHF OSC C2
UHF OSC B2
UHF OSC B1
UHF OSC C1
VHI OSC C
VHI OSC B
OSC GND
VLO OSC C
VLO OSC B
FUNCTIONAL BLOCK DIAGRAM
IF
Amplifier
UHF
Oscillator
DIF OUT1
DIF OUT2
AIF OUT
VLO RF IN
VHF-L
Mixer
VHF-H
Mixer
IF GND
UHF
Mixer
RF AGC OUT
RF
AGC
Detect
VHI RF IN
RF AGC BUFF
UHF RF IN1
UHF RF IN2
CP
Programmable
Divider
RF GND
XTAL1
XTAL2
VTU
Operational
Amplifier
XTAL
Oscillator
128/80/64/50/
28/24 Div
Phase
Detector
Charge
Pump
VCC
XTAL OUT
NPN Band-Switch Port
SCL
SDA
2
I C Bus
Interface
IF
GCA
IF GCA OUT2
AS
IF GCA GND
2
Submit Documentation Feedback
IF GCA CTRL
IF GCA IN1
IF GCA IN2
BS1
BS2
BS3
BS4
5-Level
ADC
P5/ADC
BUS GND
IF GCA OUT1
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
TERMINAL FUNCTIONS
TERMINAL
NAME
DESCRIPTION
NO.
SCHEMATIC
AIF OUT
13
IF amplifier output (analog)
Figure 8
AS
28
Address selection input
Figure 1
BS1
31
Band switch 1 output
Figure 2
BS2
32
Band switch 2 output
Figure 2
BS3
33
Band switch 3 output
Figure 2
BS4
44
Band switch 4 output
Figure 2
BUS GND
27
BUS ground
CP
10
Charge-pump output
Figure 3
DIF OUT1
14
IF amplifier output 1
Figure 9
DIF OUT2
15
IF amplifier output 2
Figure 9
IF GCA CTRL
16
IF GCA CTRL voltage inout
Figure 4
IF GCA GND
20
IF GCA ground
IF GCA IN1
18
IF GCA input 1
Figure 5
IF GCA IN2
19
IF GCA input 2
Figure 5
IF GCA OUT1
22
IF GCA output 1
Figure 6
IF GCA OUT2
21
IF GCA output 2
Figure 6
IF GND
12
IF ground
IF IN
36
IF amplifier input
Figure 7
MIXOUT1
37
Mixer output 1
Figure 10
MIXOUT2
38
Mixer output 2
Figure 10
OSC GND
9
Oscillator ground
P5/ADC
26
Port-5 output/ADC input
Figure 11
RF AGC BUF
34
RF AGC buffer output
Figure 12
RF AGC OUT
35
RF AGC output
Figure 13
RF GND
39
RF ground
SCL
29
Serial clock input
Figure 14
SDA
30
Serial data input/output
Figure 15
UHF OSC B1
5
UHF oscillator base 1
Figure 16
UHF OSC B2
8
UHF oscillator base 2
Figure 16
UHF OSC C1
6
UHF oscillator collector 1
Figure 16
UHF OSC C2
7
UHF oscillator collector 2
Figure 16
UHF RF IN1
43
UHF RF input 1
Figure 17
UHF RF IN2
42
UHF RF input 2
Figure 17
VCC
17
Supply voltage for mixer/oscillator/PLL: 5 V
VHI OSC B
3
VHF-H oscillator base
Figure 18
VHI OSC C
4
VHF-H oscillator collector
Figure 18
VHI RF IN
41
VHF-H RF input
Figure 19
VLO OSC B
1
VHF-L oscillator base
Figure 20
VLO OSC C
2
VHF-L oscillator collector
Figure 20
VLO RF IN
40
VHF-L RF input
Figure 21
VTU
11
Tuning voltage amplifier output
Figure 3
XTAL1
23
4-MHz crystal oscillator output
Figure 22
XTAL2
24
4-MHz crystal oscillator input
Figure 22
XTALOUT
25
4-MHz crystal oscillator buffer output
Figure 23
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
3
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
500 W
28
31
10 W
32
33
50 kW
Figure 1. AS
44
Figure 2. BS1, BS2, BS3, and BS4
11
1 kW
16
25 W
100 kW
10
25 W
Figure 3. CP and VTU
Figure 4. IF GCA CTRL
Vbias
1 kW
1 kW
18
19
15 W
21
22
Figure 5. IF GCA IN1 and IF GCA IN2
2 kW
Figure 6. IF GCA OUT1 and IF GCA OUT2
1 kW
A
10 W
13
36
1 kW
1 kW
Figure 7. IF IN
4
Figure 8. AIF OUT
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
37
38
10 W
A
14
15
Figure 9. DIF OUT1 and DIF OUT2
25 W
Figure 10. MIXOUT1 and MIXOUT2
25 W
50 W
34
26
Figure 11. P5/ADC
Figure 12. RF AGC BUF
1 kW
35
29
Figure 13. RF AGC OUT
25 W
Figure 14. SCL
7
6
8
5
1 kW
30
8 kW
Figure 15. SDA
8 kW
Figure 16. UHF OSC B1, UHF OSC B2, UHF OSC C1, and
UHF OSC C2
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
5
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
4
42
43
3
8 kW
Figure 17. UHF RF IN1 and UHF RF IN2
8 kW
Figure 18. VHI OSC B and VHI OSC C
2
41
3 kW
1
8 kW
Figure 19. VHI RF IN
8 kW
Figure 20. VLO OSC B and VLO OSC C
24
23
40
20 W
10 W
3 kW
50 kW
Figure 21. VLO RF IN
Figure 22. XTAL1 and XTAL2
50 W
25
Figure 23. XTALOUT
6
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
ABSOLUTE MAXIMUM RATINGS (1)
over recommended operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC
Supply voltage range
(2)
VCC
–0.4
6.5
V
VGND
Input voltage range 1
(2)
RF GND, OSC GND
–0.4
0.4
V
VTU
Input voltage range 2
(2)
VTU
–0.4
35
V
VIN
Input voltage range 3
(2)
Other pins
–0.4
6.5
PD
Continuous total dissipation
TA
Operating free-air temperature range
–20
85
°C
Tstg
Storage temperature range
–65
150
°C
TJ
Maximum junction temperature
150
°C
tSC(max)
Maximum short-circuit time
10
s
(1)
(2)
(3)
(3)
TA ≤ 25°C
1438
Each pin to VCC or to GND
UNIT
V
mW
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Voltage values are with respect to the IF GND of the circuit.
Derating factor is 11.5 mW/°C for TA ≥ 25°C.
RECOMMENDED OPERATING CONDITIONS
MIN
VCC
Supply voltage
VCC
VTU
Tuning supply voltage
VTU
IBS
Output current of band switch
BS1 – BS4, one band switch on
IP5
Output current of port 5
P5/ADC
TA
Operating free-air temperature
4.5
–20
NOM
MAX
UNIT
5
5.5
30
33
V
10
mA
–5
mA
85
°C
V
xxx
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
IF IN1, MIXOUT1, and MIXOUT2 (pins 36–38) withstand 1.5 kV, and all other pins withstand 2 kV, according to the Human-Body
Model (1.5 kΩ, 100 pF).
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
7
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
ELECTRICAL CHARACTERISTICS
Total Device and Serial Interface
VCC = 4.5 V to 5.5 V, TA = –20°C to 85°C (unless otherwise noted)
TYP
MAX
UNIT
ICC1
Supply current 1
PARAMETER
BS[1:4] = 0100, IFGCA disabled
TEST CONDITIONS
MIN
90
120
mA
ICC2
Supply current 2
BS[1:4] = 0100, IFGCA enabled
115
145
mA
ICC3
Supply current 3
BS[1:4] = 0100, IFGCA enabled,
IBS = 10 mA
125
155
mA
ICC-STBY
Standby supply current
BS[1:4] = 1100
VIH
High-level input voltage (SCL, SDA)
VIL
Low-level input voltage (SCL, SDA)
1.05
V
IIH
High-level input current (SCL, SDA)
10
µA
IIL
Low-level input current (SCL, SDA)
–10
VPOR
Power-on-reset supply voltage (threshold of supply
voltage between reset and operation mode)
2.1
9
mA
2.3
V
µA
2.8
3.5
V
5
V
2
I C Interface
VASH
Address-select high-input voltage (AS)
VCC = 5 V
4.5
VASM1
Address-select mid-input 1 voltage (AS)
VCC = 5 V
2
3
V
VASM2
Address-select mid-input 2 voltage (AS)
VCC = 5 V
1
1.5
V
VASL
Address-select low-input voltage (AS)
VCC = 5 V
0.5
V
IASH
Address-select high-input current (AS)
50
µA
IASL
Address-select low-input current (AS)
VADC
ADC input voltage
See Table 10
IADH
ADC high-level input current
VADC = VCC
IADL
ADC low-level input current
VADC = 0 V
VOL
Low-level output voltage (SDA)
VCC = 5 V, IOL = 3 mA
0.4
V
lSDAH
High-level output leakage current (SDA)
VSDA = 5.5 V
10
µA
fSCL
Clock frequency (SCL)
400
kHz
tHD-DAT
Data hold time
0.9
µs
tBUF
Bus free time
1.3
µs
tHD-STA
Start hold time
0.6
µs
tLOW
SCL-low hold time
1.3
µs
tHIGH
SCL-high hold time
0.6
µs
tSU-STA
Start setup time
0.6
µs
tSU-DAT
Data setup time
0.1
tr
Rise time (SCL, SDA )
0.3
µs
tf
Fall time (SCL, SDA)
0.3
µs
tSU-STO
Stop setup time
8
µA
–10
0
0
0.6
Submit Documentation Feedback
V
10
µA
µA
–10
100
See Figure 24
VCC
µs
µs
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
PLL and Band Switch
VCC = 4.5 V to 5.5 V, TA = –20°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
N
Divider ratio
15-bit frequency word
fXTAL
Crystal oscillator frequency
RXTAL = 25 Ω to 300 Ω
ZXTAL
Crystal oscillator input impedance
MIN
VXLO
XTALOUT output voltage
VVTUL
Tuning amplifier low-level output voltage
RL = 20 kΩ, VTU = 33 V
IVTUOFF
Tuning amplifier leakage current
Tuning amplifier = off, VTU = 33 V
0.2
0.4
Vp-p
0.3
CP[2:0] = 011
600
CP[2:0] = 010
350
CP[2:0] = 001
140
ICP00
CP[2:0] = 000
70
ICP100
CP[2:0] = 100, Mode = 1
VCP
Charge-pump output voltage
PLL locked
ICPOFF
Charge-pump leakage current
VCP = 2 V, TA = 25°C
IBS
Band switch driver output current (BS1–BS4)
VBS1
VBS2
Band switch driver output voltage (BS1–BS4)
IBSOFF
Band switch driver leakage current
(BS1–BS4)
IP5
Band switch port sink current (P5/ADC)
VP5ON
Band switch port output voltage (P5/ADC)
MHz
kΩ
ICP10
Charge-pump current
0.46
V
10
µA
µA
900
1.95
–15
IBS = 10 mA
V
15
nA
10
mA
3
IBS = 10 mA, VCC = 5 V, TA = 25°C
UNIT
2.4
ICP11
ICP01
MAX
32767
4
1.6
Load = 10 pF/5.1 kΩ, VCC = 5 V,
TA = 25°C
TYP
512
3.5
V
3.7
8
µA
–5
mA
0.6
V
VBS = 0 V
IP5 = –2 mA, VCC = 5 V, TA = 25°C
RF AGC (1)
VCC = 5 V, TA = 25°C, measured in Figure 25 reference measurement circuit at 50-Ω system, IF = 44 MHz,
IF filter characteristics: fpeak = 44 MHz (unless otherwise noted)
PARAMETER
IOAGC0
IOAGC1
TEST CONDITIONS
RF AGC output source current
MIN
TYP
MAX
UNIT
ATC = 0
300
nA
ATC = 1
9
µA
µA
IOAGCSINK
RF AGC peak sink current
ATC = 0
VOAGCH
RFAGCOUT output high voltage (max level)
ATC = 1
VOAGCL
RFAGCOUT output low voltage (min level)
ATC = 1
0.3
V
IAGCBUF
RFAGCBUF output current
ATC = 0
1.5
mA
VOAGCBFH
RFAGCBUF output high voltage (max level)
ATC = 1
VOAGCBFL
RFAGCBUF output low voltage (min level)
ATC = 1
0.3
VAGCSP00
ATP[2:0] = 000
114
VAGCSP01
ATP[2:0] = 001
112
VAGCSP02
ATP[2:0] = 010
110
ATP[2:0] = 011
108
VAGCSP04
ATP[2:0] = 100
106
VAGCSP05
ATP[2:0] = 101
104
VAGCSP06
ATP[2:0] = 110
102
VAGCSP03
(1)
Start-point IF output level
100
3.5
3.5
4
4
4.5
4.5
V
V
V
dBµV
When AISL=1, RF AGC function is not available at VHF-L band (output level is undefined).
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
9
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
Mixer, Oscillator, IF Amplifier (DIF OUT)
VCC = 5 V, TA = 25°C, measured in Figure 25 reference measurement circuit at 50-Ω system, IF = 44 MHz,
IF filter characteristics: fpeak = 44 MHz (unless otherwise noted)
PARAMETER
GC1D
GC3D
GC4D
GC6D
GC7D
GC9D
NF1D
NF3D
NF4D
NF6D
NF7D
NF9D
CM1D
CM3D
CM4D
CM6D
CM7D
CM9D
VIFO1D
VIFO3D
VIFO4D
VIFO6D
VIFO7D
VIFO9D
ΦPLVL1D
ΦPLVL3D
ΦPLVL4D
ΦPLVL6D
ΦPLVL7D
ΦPLVL9D
(1)
(2)
(3)
(4)
10
TEST CONDITIONS
Conversion gain (mixer-IF amplifier), VHF-LOW
Conversion gain (mixer-IF amplifier), VHF-HIGH
Conversion gain (mixer-IF amplifier), UHF
Noise figure, VHF-LOW
Noise figure, VHF-HIGH
Noise figure, UHF
TYP
fin = 57 MHz (1)
35
fin = 171 MHz (1)
35
fin = 177 MHz (1)
35
(1)
35
fin = 473 MHz (1)
35
fin = 864 MHz (1)
35
fin = 467 MHz
fin = 57 MHz
9
fin = 171 MHz
9
fin = 177 MHz
9
fin = 467 MHz
10
fin = 473 MHz
10
fin = 864 MHz
12
Input voltage causing 1% cross-modulation distortion,
VHF-LOW
fin = 57 MHz (2)
(2)
79
Input voltage causing 1% cross-modulation distortion,
VHF-HIGH
fin = 177 MHz (2)
79
fin = 467 MHz (2)
79
fin = 473 MHz (2)
77
fin = 864 MHz (2)
77
Input voltage causing 1% cross-modulation distortion, UHF
IF output voltage, VHF-LOW
IF output voltage, VHF-HIGH
IF output voltage, UHF
Phase noise, VHF-LOW
Phase noise, VHF-HIGH
Phase noise, UHF
fin = 171 MHz
79
fin = 57 MHz
117
fin = 171 MHz
117
fin = 177 MHz
117
fin = 467 MHz
117
fin = 473 MHz
117
fin = 864 MHz
117
fin = 57 MHz (3)
–90
fin = 171 MHz (4)
–85
fin = 177 MHz (3)
–85
fin = 467 MHz (4)
–77
fin = 473 MHz (3)
–80
(4)
–77
fin = 864 MHz
UNIT
dB
dB
dB
dB
dB
dB
dBµV
dBµV
dBµV
dBµV
dBµV
dBµV
dBc/Hz
dBc/Hz
dBc/Hz
IF = 44 MHz, RF input level = 70 dBµV, differential output
fundes = fdes ±6 MHz, Pin = 70 dBµV, AM 1 kHz, 30%, DES/CM = S/I = 46 dB
Offset = 1 kHz, CP current = 350 µA, reference divider = 64
Offset = 1 kHz, CP current = 900 µA, reference divider = 64
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
Mixer, Oscillator, IF Amplifier (AIF OUT)
VCC = 5 V, TA = 25°C, measured in Figure 25 reference measurement circuit at 50-Ω system, IF = 45.75 MHz,
IF filter characteristics: fpeak = 44 MHz (unless otherwise noted)
PARAMETER
GC1A
GC3A
GC4A
GC6A
GC7A
GC9A
NF1A
NF3A
NF4A
NF6A
NF7A
NF9A
CM1A
CM3A
CM4A
CM6A
CM7A
CM9A
VIFO1A
VIFO3A
VIFO4A
VIFO6A
VIFO7A
VIFO9A
ΦPLVL1A
ΦPLVL3A
ΦPLVL4A
ΦPLVL6A
ΦPLVL7A
ΦPLVL9A
(1)
(2)
(3)
TEST CONDITIONS
Conversion gain (mixer-IF amplifier), VHF-LOW
Conversion gain (mixer-IF amplifier), VHF-HIGH
Conversion gain (mixer-IF amplifier), UHF
Noise figure, VHF-LOW
Noise figure, VHF-HIGH
Noise figure, UHF
TYP
fin = 55.25 MHz (1)
29
fin = 169.25 MHz (1)
29
fin = 175.25 MHz (1)
29
(1)
29
fin = 471.25 MHz (1)
29
fin = 862.25 MHz (1)
29
fin = 465.25 MHz
fin = 55.25 MHz
9
fin = 169.25 MHz
9
fin = 175.25 MHz
9
fin = 465.25 MHz
10
fin = 471.25 MHz
10
fin = 862.25 MHz
12
Input voltage causing 1% cross-modulation distortion,
VHF-LOW
fin = 55.25 MHz (2)
(2)
79
Input voltage causing 1% cross-modulation distortion,
VHF-HIGH
fin = 175.25 MHz (2)
79
fin = 465.25 MHz (2)
79
fin = 471.25 MHz (2)
79
fin = 862.25 MHz (2)
77
Input voltage causing 1% cross-modulation distortion, UHF
IF output voltage, VHF-LOW
IF output voltage, VHF-HIGH
IF output voltage, UHF
Phase noise, VHF-LOW
Phase noise, VHF-HIGH
Phase noise, UHF
fin = 169.25 MHz
79
fin = 55.25 MHz
117
fin = 169.25 MHz
117
fin = 175.25 MHz
117
fin = 465.25 MHz
117
fin = 471.25 MHz
117
fin = 862.25 MHz
117
fin = 55.25 MHz (3)
–95
fin = 169.25 MHz (3)
–95
fin = 175.25 MHz (3)
–90
fin = 465.25 MHz (3)
–90
fin = 471.25 MHz (3)
–85
(3)
–90
fin = 862.25 MHz
UNIT
dB
dB
dB
dB
dB
dB
dBµV
dBµV
dBµV
dBµV
dBµV
dBµV
dBc/Hz
dBc/Hz
dBc/Hz
IF = 44 MHz, RF input level = 70 dBµV, differential output
fundes = fdes ±6 MHz, Pin = 70 dBµV, AM 1 kHz, 30%, DES/CM = S/I = 46 dB
Offset = 10 kHz, CP current = 70 µA, reference divider = 128
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
11
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
IF Gain Controlled Amplifier
VCC = 5 V, TA = 25°C, measured in Figure 25 reference measurement circuit at 50-Ω system, IF = 44 MHz
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
30
60
UNIT
µA
3
VCC
V
0
0.2
V
IIFGCA
Input current (IF GCA CTRL)
VIFGCA = 3 V
VIFGCAMAX
Maximum gain control voltage
Gain maximum
VIFGCAMIN
Minimum gain control voltage
Gain minimum
GIFGCAMAX
Maximum gain
VIFGCA = 3 V
65
dB
GIFGCAMIN
Minimum gain
VIFGCA = 0 V
–1
dB
GCRIFGCA
Gain control range
VIFGCA = 0 V to 3 V
66
dB
VIFGCAOUT
Output voltage
Single-ended output,
VIFGCA = 3 V
2.1
Vp-p
NFIFGCA
Noise figure
VIFGCA = 3 V
8.5
dB
IM3IFGCA
Third order intermodulation distortion
fIFGCAIN1 = 43 MHz,
fIFGCAIIN2 = 44 MHz,
VIFGCAOUT = –2 dBm,
VIFGCA = 3 V
–50
dBc
IIP3IFGCA
Input intercept point
VIFGCA = 0 V
11
dBm
RIFGCAIN
Input resistance (IF GCA IN1, IF GCA IN2)
1
kΩ
RIFGCAOUT
Output resistance (IF GCA OUT1, IF GCA OUT2)
25
Ω
12
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
FUNCTIONAL DESCRIPTION
I2C Bus Mode
I2C Write Mode (R/W = 0)
Table 1. Write Data Format
MSB
LSB
Address byte (ADB)
1
1
0
0
0
MA1
MA0
R/W = 0
A (1)
Divider byte 1 (DB1)
0
N14
N13
N12
N11
N10
N9
N8
A (1)
Divider byte 2 (DB2)
N7
N6
N5
N4
N3
N2
N1
N0
A (1)
Control byte 1 (CB1)
1
0
ATP2
ATP1
ATP0
RS2
RS1
RS0
A (1)
CP1
CP0
AISL
P5
BS4
BS3
BS2
BS1
A (1)
1
1
ATC
MODE
T3/DISGCA
T2/IFDA
T1/CP2
T0/XLO
A (1)
Band switch byte (BB)
Control byte 2 (CB2)
(1)
A : acknowledge
Table 2. Write Data Symbol Description
SYMBOL
DESCRIPTION
MA[1:0]
Address-set bits (see Table 3)
N[14:0]
Programmable counter set bits
14
N = N14 × 2
DEFAULT
N14 = N13 = N12 = ... = N0 = 0
13
+ N13 × 2
+ ... + N1 × 2 + N0
ATP[2:0]
RF AGC start-point control bits (see Table 4)
ATP[2:0] = 000
RS[2:0]
Reference divider ratio-selection bits (see Table 5)
RS[2:0] = 000
CP[1:0]
Charge-pump current-set bit (see Table 6)
CP[1:0] = 00
AISL
RF AGC detector input selection bit
AISL = 0
AISL = 0: IF amplifier
AISL = 1: Mixer output
P5
Port output/ADC input control bit
P5 = 0
P5 = 0: ADC INPUT
P5 = 1: Tr = ON
BS[4:1]
Band switch control bits
BSn = 0
BSn = 0: Tr = OFF
BSn = 1: Tr = ON
Band selection by BS[1:2]
ATC
BS1
BS2
1
0
0
1
0
1
0
1
VHF-LO
VHF-HI
UHF
Standby mode/stop MOP function (XTALOUT is available in standby
mode)
RF AGC current-set bit
ATC = 0
ATC = 0: Current = 300 nA
ATC = 1: Current = 9 µA
Mode
T3/DISGCA
T2/IFDA
T1/CP2
T0/XLO
Mode = 0 : IFGCA enabled, DIFOUT1, 2 selected
T3/DISGCA, T2/IFDA, T1/CP2, T0/XLO are Test bits and XTALOUT control bit (see
Table 7)
MODE = 0
T[3:0] = 0000
Mode = 1
T3/DISGCA = 0 : IF GCA enabled
T3/DISGCA = 1 : IF GCA disabled
T2/IFDA = 0 : DIFOUT1, 2 selected
T2/IFDA = 1 : AIFOUT selected
T1/CP2 : lcp control bit, See Table 6
T0/XLO = 0 : XTALOUT enabled
T0/XLO = 1 : XTALOUT disabled
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
13
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
Table 3. Address Selection
MA1
MA0
0
0
0 V to 0.1 VCC (Low)
VOLTAGE APPLIED ON AS INPUT
0
1
OPEN, or 0.2 VCC to 0.3 VCC (Mid2)
1
0
0.4 VCC to 0.6 VCC (Mid1)
1
1
0.9 VCC to VCC (High)
Table 4. RF AGC Start Point (1)
(1)
ATP2
ATP1
ATP0
IFOUT LEVEL (dBµV)
0
0
0
114
0
0
1
112
0
1
0
110
0
1
1
108
1
0
0
106
1
0
1
104
1
1
0
102
1
1
1
Disabled
When AISL=1, RF AGC function is not available at VHF-L band (output level is undefined).
Table 5. Reference Divider Ratio
RS2
RS1
RS0
REFERENCE DIVIDER RATIO
0
0
0
24
0
0
1
28
0
1
0
32
0
1
1
64
1
0
0
128
1
X
1
80
Table 6. Charge-Pump Current
14
CHARGE PUMP CURRENT
(µA)
MODE
CP2
CP1
CP0
X
0
0
0
70
X
0
0
1
140
X
0
1
0
350
X
0
1
1
600
1
1
0
0
900
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
Table 7. Test Bits/XTALOUT Control
(1)
(1)
XTALOUT
4-MHz OUTPUT
MODE
T3/DISGCA
T2/IFDA
T1/CP2
T0/XLO
DEVICE OPERATION
0
0
0
0
0
Normal operation
Enabled
0
0
0
0
1
Normal operation
Disabled
1
X
X
X
0
Normal operation
Enabled
1
X
X
X
1
Normal operation
Disabled
0
X
1
X
X
Test mode
Not available
0
1
X
X
X
Test mode
Not available
RFAGC and XTALOUT are not available in test mode.
Example I2C Data Write Sequences
Telegram examples:
Start-ADB-DB1-DB2-CB1-BB-CB2-Stop
Start-ADB-DB1-DB2-Stop
Start-ADB-CB1-BB-CB2-Stop
Start-ADB-CB1-BB-Stop
Start-ADB-CB2-Stop
Abbreviations:
ADB: Address byte
BB: Band switch byte
CB1: Control byte 1
CB2: Control byte 2
DB1: Divider byte 1
DB2: Divider byte 2
Start: Start condition
Stop: Stop condition
I2C Read Mode (R/W = 1)
Table 8. Read Data Format
MSB
Address byte (ADB)
Status byte (SB)
(1)
LSB
1
1
0
0
0
MA1
MA0
R/W = 1
A (1)
POR
FL
1
1
X
A2
A1
A0
–
A : acknowledge
Table 9. Read Data Symbol Description
SYMBOL
DESCRIPTION
MA[1:0]
Address set bits (see Table 3)
POR
Power-on-reset flag
DEFAULT
POR = 1
POR set: power on
POR reset: end-of-data transmission procedure
FL
In-lock flag
A[2:0]
Digital data of ADC (see Table 10)
PLL locked (FL = 1), unlocked (FL = 0)
Bit P5 must be set to 0.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
15
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
Table 10. ADC Level (1)
(1)
A2
A1
A0
1
0
0
0.6 VCC to VCC
VOLTAGE APPLIED ON ADC INPUT
0
1
1
0.45 VCC to 0.6 VCC
0
1
0
0.3 VCC to 0.45 VCC
0
0
1
0.15 VCC to 0.3 VCC
0
0
0
0 V to 0.15 VCC
Accuracy is 0.03 × VCC.
t HD STA
-
t SU STA
-
tHIGH
t
F
SCL
t SUDAT
tLOW
t SUSTO
-
tR
SDA
t HD DAT
tBUF
Figure 24. I2C Timing Chart
16
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
APPLICATION INFORMATION
C9
C10
R5
VC1
C1 R1
L1
1 VLO OSC B
BS4 44
2 VLO OSC C
UHF RF IN1 43
3 VHI OSC B
UHF RF IN2 42
4 VHI OSC C
VHI RF IN 41
BS4
C2
R6
C37
R2
C11 VC2
C4
C5 R3
VC3
L4
R37
VHI RF IN
R38
VLO RF IN
C40
L2
C12
UHF RF IN1
C39
C3
VC4
R7
R36
C42
5 UHF OSC B1
VLO RF IN 40
6 UHF OSC C1
RF GND 39
7 UHF OSC C2
MIX OUT2 38
C6
C14
L3
R8
L6
C7
C15
C13
R10
C49
L10
8 UHF OSC B2
R9
L11
C47
C8 R4
MIX OUT1 37
R42
L5
C16
9 OSC GND
(See Note A)
IF IN 36
C19
C18
VTU
10 CP
RF AGC OUT 35
11 VTU
RF AGC BUF 34
RF AGC OUT
R12
R11
C51
RF AGC BUF
C17
C52
12 IF GND
BS3 33
BS3
13 AIF OUT
BS2 32
BS2
14 DIF OUT1
BS1 31
BS1
15 DIF OUT2
SDA 30
16 IF GCA CTRL
SCL 29
C20
AIF OUT
R21
R15
C21
DIF OUT
R19
R17
R48
C23
SDA
C56
R46
R49 C62
IF GCA CTRL
C61
SCL
C30
R50 C63
17 VCC
VCC
AS 28
AS
R24
C26
IF GCA IN1
R25
C65
18 IF GCA IN1
BUS GND 27
19 IF GCA IN2
P5/ADC 26
C64
C28
P5/ADC
R23
20 IF GCA GND
R30 R28
XTAL OUT
XTAL OUT 25
C57
R47
C58
C32
21 IF GCA OUT2
XTAL2 24
C59
R34 R31
X1
C34
22 IF GCA OUT1
IF GCA OUT1
XTAL1 23
C60
A.
To prevent abnormal oscillation, connect C16, which does not affect a PLL.
B.
This application information is advisory and performance-check is required at actual application circuits. TI assumes
no responsibility for the consequences of use of this circuit, such as an infringement of intellectual property rights or
other rights, including patents, of third parties.
Figure 25. Reference Measurement Circuit
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
17
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
Component Values for Measurement Circuit
PARTS NAME
VALUE
PARTS NAME
VALUE
C1 (VLO OSC B)
1 pF
L1 (VLO OSC)
3.0 mm, 7T, wire 0.32 mm
C2 (VLO OSC C)
2 pF
L2 (VHI OSC)
2.0 mm, 3T, wire 0.4 mm
C3 (VHI OSC B)
7 pF
L3 (UHF OSC)
1.8 mm, 3T, wire 0.4 mm
C4 (VHI OSC C)
5 pF
L4 (UHF OSC)
1.8 mm, 3T, wire 0.4 mm
C5 (UHF OSCB1)
1.5 pF
L5 (MIX OUT)
680 nH (LK1608R68K-T)
C6 (UHF OSCC1)
1 pF
L6 (MIX OUT)
680 nH (LK1608R68K-T)
C7 (UHF OSCC2)
1 pF
L10 (MIX OUT)
Short
C8 (UHF OSCB2)
1.5 pF
L11 (MIX OUT)
Short
C9 (VLO OSC)
OPEN
R1(VLO OSC B)
0
C10(VLO OSC)
43 pF
R2 (VHI OSC B)
4.7 Ω
C11 (VHI OSC)
51 pF
R3 (UHF OSC B1)
4.7 Ω
C12 (VHI OSC)
0.5 pF
R4 (UHF OSC B2)
0
C13 (UHF OSC)
10 pF
R5 (VLO OSC)
3.3 kΩ
C14 (UHF OSC)
100 pF
R6 (VHI OSC)
3.3 kΩ
C15 (VTU)
2.2 nF/50 V
R7 (VHI OSC)
3.3 kΩ
C16 (CP)
150 pF/50 V
R8 (UHF OSC)
1 kΩ
C17 (VTU)
2.2 nF/50 V
R9 (UHF OSC)
2.2 k
C18(CP)
0.01 u/50 V
R10 (VTU)
3 kΩ
C19(CP)
22 pF/50 V
R11 (VTU)
20 kΩ
C20 (AIF OUT)
2.2 nF
R12 (CP)
47 kΩ
C21 (DIF OUT1)
2.2 nF
R15 (DIF OUT1)
200 Ω
C23 (DIF OUT2)
2.2 nF
R17 (DIF OUT2)
200 Ω
C26 (IF GCA IN1)
2.2 nF
R19 (DIF OUT2)
50 Ω
C28 (IF GCA IN2)
2.2 nF
R21 (DIF OUT1)
0
C30 (VCC)
0.1 uF
R23 (P5/ADC)
Open
C32 (IF GCA OUT1)
2.2 nF
R24 (IF GCA IN1)
(50 Ω)
C34 (IF GCA OUT2)
2.2 nF
R25 (IF GCA IN2)
0
C37 (UHF RF IN1)
2.2 nF
R28 (IF GCA OUT1)
200 Ω
C39 (UHF RFIN2)
2.2 nF
R30 (IF GCA OUT1)
50 Ω
C40 (VHI RF IN)
2.2 nF
R31 (IF GCA OUT2)
200 Ω
C42 (VLO RF IN)
2.2 nF
R34 (IF GCA OUT2)
0
C47 (MIX OUT)
6 pF
R36 (UHF RF IN1)
(50 Ω)
C49 (MIX OUT)
2.2 nF
R37 (VHI RF IN)
(50 Ω)
C51 (RF AGC OUT)
0.15 uF
R38 (VLO RF IN)
(50 Ω)
C52 (RF AGC BUF)
Open
R42 (MIX OUT)
0
C56 (IFGCA CTRL)
0.1 µF
R46 (IFGCA CTRL)
0
C57 (XTAL OUT)
0.01 uF
R47 (XTAL OUT)
5.1 kΩ
C58 (XTAL OUT)
10 pF
R48 (SDA)
330 Ω
C59(XTAL)
27 pF
R49 (SCL)
330 Ω
C60 (XTAL)
27 pF
R50 (AS)
Open
C61 (VCC)
2.2 nF
VC1 (VLO OSC)
MA2S374
C62 (SDA)
Open
VC2 (VHI OSC)
MA2S374
C63 (SCL)
Open
VC3 (UHF OSC)
MA2S372
C64 (AS)
Open
VC4 (VHI OSC)
MA2S372
C65 (AS)
22 pF
X1
4-MHz crystal
18
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
APPLICATION INFORMATION (CONTINUED)
Test Circuits
DUT
SG
50 W
50 W
VIN
DIF OUT1
VLO RF IN1
(VHI RF IN)
Spectrum
Analyzer
VOUT Diff 200 W
VOUT
DIF OUT2
50 W
Gv = 20log(VOUT Diff/VIN)
= 20log(VOUT/VIN) + 6 + 14
250 W
Figure 26. VHF-Conversion Gain-Measurement Circuit (at DIFOUT)
DUT
SG
50 W
50 W
VIN
VLO RF IN1
(VHI RF IN)
Spectrum
Analyzer
AIFOUT
Gv = 20log(VOUT/VIN)
VOUT
50 W
Figure 27. VHF-Conversion Gain Measurement Circuit (at AIFOUT)
DUT
SG
UHF RF IN1
50 W
50 W
VIN
DIF OUT1
UHF RF IN2
Spectrum
Analyzer
VOUT Diff 200 kW
VOUT
DIF OUT2
50 W
Gv = 20log(VOUT Diff/VIN)
= 20log(VOUT/VIN) + 6 + 14
250 W
Figure 28. UHF-Conversion Gain-Measurement Circuit (at DIFOUT)
DUT
SG
UHFRF IN1
50 W
50 W
VIN
Spectrum
Analyzer
AIFOUT
UHFRF IN2
Gv = 20log(VOUT/VIN)
VOUT
50 W
Figure 29. UHF-Conversion Gain Measurement Circuit (at AIFOUT)
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
19
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
DUT
SG
IFGCAIN1
50 W
50 W
VIN
IFGCAIN2
IFGCAOUT1
VOUT
IFGCAOUT2
IFGCACTRAL
Spectrum
Analyzer
VOUT Diff 200 W
50 W
Gv = 20log(VOUT Diff/VIN)
= 20log(VOUT/VIN) + 6 + 14
250 W
DC Power
Source
Figure 30. IF GCA Gain Measurement Circuit
NF
Meter
Noise
Source
DUT
Figure 31. Noise-Figure Measurement Circuit
Signal
Generator
fdes: P = 70 dBmV
Signal
Generator
Mix
Pad
fdes ±6 MHz
AM 30%, 1 kHz
DUT
Modulation
Analyzer
Figure 32. 1% Cross-Modulation Distortion Measurement Circuit
20
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
TYPICAL CHARACTERISTICS
Band Switch Driver Output Voltage (BS1–BS4)
BS OUTPUT CURRENT
vs
OUTPUT VOLTAGE
Band Switch Output Voltage – V
5.0
4.5
VCC = 5.5 V
4.0
VCC = 5.0 V
3.5
VCC = 4.5 V
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
2
4
6
8
10
12
14
16
18
20
Band Switch Current – mA
Figure 33. Band Switch Driver Output Voltage
S-Parameter
40
40MHz
MHz
500
500MHz
MHz
Figure 34. VLO RFIN, VHI RFIN
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
21
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS (continued)
900
500MHz
MHz
350
40MHz
MHz
Figure 35. UHF RFIN
60 MHz
30 MHz
500MHz
Figure 36. DIFOUT
22
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
TYPICAL CHARACTERISTICS (continued)
60 MHz
30 MHz
500MHz
Figure 37. AIFOUT
20 MHz
70 MHz
500MHz
40MHz
Figure 38. IF GCA IN
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
23
SN761640
SLES237 – OCTOBER 2008 .............................................................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS (continued)
70 MHz
20 MHz
500MHz
40MHz
Figure 39. IF GCAOUT
70
60
VCC = 5.5 V
Gain (dB)
50
40
30
VCC = 5.0 V
VCC = 4.5 V
20
10
0
–10
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
IF GCA CTRL Voltage (V)
Figure 40. IF GCA Gain vs Control Voltage 1
24
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
SN761640
www.ti.com .............................................................................................................................................................................................. SLES237 – OCTOBER 2008
TYPICAL CHARACTERISTICS (continued)
70
60
Gain (dB)
85°C
–20°C
50
25°C
40
30
20
10
0
-10
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
IF GCA CTRL Voltage (V)
Figure 41. IF GCA Gain vs Control Voltage 2
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): SN761640
25
PACKAGE OPTION ADDENDUM
www.ti.com
26-Mar-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
SN761640DBTR
OBSOLETE
Package Type Package Pins Package
Drawing
Qty
TSSOP
DBT
44
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
TBD
Call TI
Call TI
Op Temp (°C)
Device Marking
(4/5)
-20 to 85
SN761640
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OUTLINE
DBT0044A
TSSOP - 1.2 mm max height
SCALE 1.500
SMALL OUTLINE PACKAGE
SEATING
PLANE
6.6
TYP
6.2
A
C
0.1 C
PIN 1 INDEX
AREA
42X 0.5
44
1
2X
10.5
11.1
10.9
NOTE 3
22
23
44X
B
4.5
4.3
NOTE 4
0.27
0.17
0.08
1.2 MAX
C A B
0.25
GAGE PLANE
0.15
0.05
(0.15) TYP
SEE DETAIL A
0 -8
0.75
0.50
DETAIL A
A 20
TYPICAL
4220223/A 02/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
www.ti.com
EXAMPLE BOARD LAYOUT
DBT0044A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
SYMM
44X (1.5)
(R0.05) TYP
1
44
44X (0.3)
42X (0.5)
SYMM
23
22
(5.8)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
EXPOSED METAL
0.05 MAX
ALL AROUND
NON-SOLDER MASK
DEFINED
(PREFERRED)
0.05 MIN
ALL AROUND
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
15.000
4220223/A 02/2017
NOTES: (continued)
5. Publication IPC-7351 may have alternate designs.
6. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DBT0044A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
44X (1.5)
SYMM
(R0.05) TYP
1
44
44X (0.3)
42X (0.5)
SYMM
23
22
(5.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE: 8X
4220223/A 02/2017
NOTES: (continued)
7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
8. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES
Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,
reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are
developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you
(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of
this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources.
You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your
applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications
(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You
represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)
anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that
might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you
will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any
testing other than that specifically described in the published documentation for a particular TI Resource.
You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include
the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO
ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS.
TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT
LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF
DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,
COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR
ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your noncompliance with the terms and provisions of this Notice.
This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.
These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation
modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
