THS3215
SBOS780C – MARCH 2016 – REVISED JUNE 2021
THS3215 650-MHz, Differential to Single-Ended DAC Output Amplifier
The flexibility provided by this two-stage amplifier
system delivers the low distortion, dc-coupled,
differential to single-ended signal processing required
by a wide range of systems.The input stage buffers
the DAC resistive termination, and converts the signal
from differential to single-ended with a fixed gain
of 2 V/V. The differential to single-ended output is
available externally for direct use, and can also be
connected through an RLC filter or attenuator to
the input of an internal output power stage (OPS).
The wideband, current-feedback, output power stage
provides all pins externally for flexible gain setting.
1 Features
•
•
•
•
•
Input stage: internal gain of 2 V/V
– Buffered differential inputs
– Single-ended low impedance output
– Full-power bandwidth: 350 MHz (2 VPP)
Output stage: gain externally configurable
– Full-power bandwidth: 270 MHz (5 VPP)
– Slew rate: 3000 V/µs
– SPDT input switch and multiplexer
Full signal path: input stage and output stage
– HD2 (20 MHz, 5 VPP to 100 Ω load): –66 dBc
– HD3 (20 MHz, 5 VPP to 100 Ω load): –68 dBc
– 10 VPP Output to 100 Ω load using split
±6.5 V supply
– 12 VPP Output to heavy capacitive loads using
single 15 V supply
Internal DC reference buffer with low-impedance
output
Power-supply range:
– Split supply: ±4 V to ±7.9 V
– Single supply: 8 V to 15.8 V
An internal 2 × 1 multiplexer (mux) to the output
power stage noninverting input provides an easy
means to select between the internal differential-tosingle-ended stage (D2S) output or an external input.
An optional on-chip midsupply buffer provides a
wideband, low-output-impedance source for biasing
during single-supply operation through the signal-path
stages. This feature provides very simple biasing for
single-supply, ac-coupled applications operating up to
a maximum 15.8-V supply. An external input to this
buffer allows for a dc error-correction loop, or a simple
output dc offset feature.
2 Applications
•
•
•
•
Digital-to-analog converter (DAC) output amplifier
Wideband arbitrary waveform generator (AWG)
output driver
Predriver to > 20-VPP output amplifier (THS3091)
Single-supply, high-capacitive load driver for piezo
elements
A companion device, the THS3217, provides the
same functional features at higher quiescent power
and bandwidth. The THS3215 and THS3217 support
the emerging high-speed Texas Instruments DACs for
AWG applications, such as the DAC38J82.
3 Description
Device Information(1)
PART NUMBER
The THS3215 combines the key signal-chain
components
required
to
interface
with
a
complementary-current
output,
digital-to-analog
converter (DAC).
PACKAGE
THS3215
(1)
VQFN (16)
BODY SIZE (NOM)
4.00 mm × 4.00 mm
For all available packages, see the package option
addendum at the end of the data sheet.
VREF
THS3215
162
100
50
x1
D2S
Stage
25
Vi
Input
Buffers
25
+
250
249
50
+
DAC
Complementary
Output Current
Output Power
Stage (OPS)
SPDT
Switch
VOUT = 5 Vi
50
Line
500
x1
RLC Filter
Gain = 5 V/V, Differential-to-Single-Ended Line Driver With Optional External Filter
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Table of Contents
1 Features............................................................................1
2 Applications..................................................................... 1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................4
6 Specifications.................................................................. 5
6.1 Absolute Maximum Ratings........................................ 5
6.2 ESD Ratings............................................................... 5
6.3 Recommended Operating Conditions.........................5
6.4 Thermal Information....................................................5
6.5 Electrical Characteristics: D2S....................................6
6.6 Electrical Characteristics: OPS................................... 7
6.7 Electrical Characteristics: D2S + OPS...................... 10
6.8 Electrical Characteristics: Midscale (DC)
Reference Buffer..........................................................11
6.9 Typical Characteristics: D2S + OPS......................... 12
6.10 Typical Characteristics: D2S Only...........................14
6.11 Typical Characteristics: OPS Only.......................... 16
6.12 Typical Characteristics: Midscale (DC)
Reference Buffer......................................................... 20
6.13 Typical Characteristics: Switching Performance..... 21
6.14 Typical Characteristics: Gain Drift...........................22
7 Parameter Measurement Information.......................... 23
7.1 Overview................................................................... 23
7.2 Frequency Response Measurement.........................23
7.3 Harmonic Distortion Measurement........................... 25
7.4 Noise Measurement..................................................26
7.5 Output Impedance Measurement............................. 26
7.6 Step-Response Measurement.................................. 26
7.7 Feedthrough Measurement.......................................26
7.8 Midscale Buffer ROUT Versus CLOAD Measurement.. 28
8 Detailed Description......................................................29
8.1 Overview................................................................... 29
8.2 Functional Block Diagram......................................... 30
8.3 Feature Description...................................................31
8.4 Device Functional Modes..........................................46
9 Application and Implementation.................................. 52
9.1 Application Information............................................. 52
10 Power Supply Recommendations..............................61
10.1 Thermal Considerations..........................................62
11 Layout........................................................................... 63
11.1 Layout Guidelines................................................... 63
11.2 Layout Example...................................................... 64
12 Device and Documentation Support..........................65
12.1 Device Support....................................................... 65
12.2 Documentation Support.......................................... 65
12.3 Receiving Notification of Documentation Updates..65
12.4 Support Resources................................................. 65
12.5 Trademarks............................................................. 65
12.6 Electrostatic Discharge Caution..............................66
12.7 Glossary..................................................................66
13 Mechanical, Packaging, and Orderable
Information.................................................................... 66
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (December 2018) to Revision C (June 2021)
Page
• Updated the numbering format for tables, figures, and cross-references throughout the document..................1
• Changed the minimum Supply current parameter from: 23 mA to: 26 mA......................................................... 6
• Changed the minimum VREF input pin gain parameter from: 0.985 V/V to: 0.975 V/V..................................... 6
• Changed the minimum Noninverting input resistance parameter from: 17.6 kΩ to: 16 kΩ................................ 7
• Changed the minimum Internal feedback resistor, RF parameter from: 17.6 kΩ to: 16 kΩ................................ 7
• Changed the Inverting input bias current – either input selected at TJ≈ 25°C from: -35 µA to: -75 µA (MIN) and
from: 35 µA to: 75 µA (MAX)...............................................................................................................................7
• Changed the maximum Input pin bias current at 0-V input from: 4 µA to: 15µA................................................ 7
• Changed the maximum Supply current parameter from: 37.9 mA to: 39 mA................................................... 10
• Changed the minimum VREF input pin gain parameter from: 0.985 V/V to: 0.975 V/V................................... 31
• Changed the Ibi parameter from: -35 µA to: -75 µA (MIN) and -35 µA to: -75 µA (MAX)..................................42
• Changed the Ibi × RF error term from: –7.095 µA to: -15.203 µA (MIN) and from: 7.095 µA to: 15.203 µA
(MAX)................................................................................................................................................................42
• Changed Total error from: –53.08 µA to: -61.19 µA (MIN) and from: 55.35 µA to: 63.46 µA (MAX)................ 42
Changes from Revision A (April 2016) to Revision B (December 2018)
Page
• Changed DC output impedance parameter: deleted maximum specification, changed test level from A to C ....
6
• Changed DC output impedance parameter: deleted maximum specification, changed test level from A to C ....
7
• Deleted minimum and maximum specifications from DC output impedance parameter.................................. 11
2
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Changes from Revision * (March 2016) to Revision A (April 2016)
Page
• Changed data sheet status from product preview to production data................................................................ 1
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
3
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Device Comparison Table
DEVICE
SMALL-SIGNAL
BANDWIDTH
0.1 VPP
(AV = 5 V/V)(1)
LARGE-SIGNAL
BANDWIDTH
5VPP
(AV = 5 V/V)
QUIESCENT
CURRENT, Icc
(±6-V SUPPLIES)
THS3215
650 MHz
270 MHz
35 mA
–64 dBc
95 mA
140 mA
THS3217
800 MHz
500 MHz
55 mA
–60 dBc
120 mA
175 mA
(1)
TOTAL HARMONIC
CONTINUOUS
DISTORTION
OUTPUT
(5 VPP, RLOAD = 100 Ω,
CURRENT
20 MHz)
PEAK
OUTPUT
CURRENT
AV is the voltage gain.
+VCC2
VMID_OUT
VREF
+VCC1
16
15
14
13
5 Pin Configuration and Functions
VMID_IN
1
12
VIN±
+IN
2
11
VOUT
±IN
3
10
DISABLE
9
VIN+
6
7
8
V01
±VCC1
±VCC2
GND
4
5
PATHSEL
(Thermal Pad)
Figure 5-1. RGV Package 16-Pin VQFN Top View
Table 5-1. Pin Functions
PIN
NO.
NAME
DESCRIPTION
1
VMID_IN
Input
DC reference buffer input
2
+IN
Input
Positive signal input to D2S
3
–IN
Input
Negative signal input to D2S
4
PATHSEL
Input
Internal SPDT switch control: low selects the internal path, and high selects the external path
5
–VCC2(1)
Power
Negative supply for input stage
6
VO1
Output
D2S external output
7
GND
Power
Ground for control pins reference
8
–VCC1(1)
Power
Negative supply for output stage
9
VIN+
Input
External OPS noninverting input
10
DISABLE
Input
Output power stage shutdown control: low enables the OPS, and high disables the OPS
11
VOUT
Output
12
VIN–
Input
13
+VCC1(1)
Power
OPS output
OPS inverting input
Positive supply for output stage
14
VREF
Input
DC offsetting input to D2S
15
VMID_OUT
Output
DC reference buffer output
16
+VCC2(1)
Power
Positive supply for input stage
Thermal Pad
(1)
4
I/O
—
Connect the thermal pad to GND for single-supply and split-supply operation. See Section 10.1
section for more information.
Throughout this document +VCC refers to the voltage applied at the +VCC1 and +VCC2 pins, and –VCC is the voltage applied at the
–VCC1 and –VCC2 pins.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
MAX
Supply, +VCC – (–VCC)
Input/output
Voltage
Current
Temperature
(1)
(2)
UNIT
16.2
(–VCC) – 0.5
(+VCC) + 0.5
Differential input voltage (IN+ – IN–)
±8
Continuous input current (IN+, IN–, VMID_IN, VIN+,
VIN–)(2)
±10
Continuous output current(2)
±30
Operating, TA
–55
105
Junction, TJ
–45
150
Storage, Tstg
–65
150
V
mA
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress
ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
Long-term continuous current for electromigration limits.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
±1000
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
±1000
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
VCC
Supply voltage
TA
Operating free-air temperature
MIN
NOM
MAX
Bipolar supply
±4
±6
±7.9
Single supply
8
12
15.8
–40
25
85
UNIT
V
°C
6.4 Thermal Information
THS3215
THERMAL
METRIC(1)
RGV (VQFN)
UNIT
16 PINS
RθJA
Junction-to-ambient thermal resistance
45
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
45
°C/W
RθJB
Junction-to-board thermal resistance
22
°C/W
ψJT
Junction-to-top characterization parameter
1
°C/W
ψJB
Junction-to-board characterization parameter
22
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
4
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
5
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.5 Electrical Characteristics: D2S
at +VCC = 6.0 V, –VCC = –6.0 V, AV = 2 V/V, 25-Ω source impedance, input common-mode voltage (VIC) = 0.25 V, external
OPS input selected (PATHSEL ≥ 1.3 V), VREF = GND, RLOAD = 100 Ω, and TJ ≈ 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
AC PERFORMANCE (Power Stage Disabled: DISABLE pin ≥ 1.3 V)
MIN
TYP
MAX
UNIT
TEST
LEVEL
(1)
(5)
Small-signal bandwidth (SSBW)
VOUT = 250 mVPP, peaking < 1.0 dB
450
MHz
C
Large-signal bandwidth (LSBW)
VOUT = 2 VPP
350
MHz
C
Bandwidth for 0.2-dB flatness
VOUT = 2 VPP
65
MHz
C
Slew rate(2)
VOUT = 4-V step
1500
V/µs
C
Overshoot and undershoot
Input tr = 1 ns, VOUT = 2-V step
2%
Rise and fall time
Input tr = 1 ns, VOUT = 2-V step
1.2
Settling time to 0.1%
Input tr = 1 ns, VOUT = 2-V step
2nd-order harmonic distortion (HD2)
f = 20 MHz, VOUT = 2 VPP
–72
3rd-order harmonic distortion (HD3)
f = 20 MHz, VOUT = 2 VPP
–88
dBc
C
Output voltage noise
f > 200 kHz
12
nV/√ Hz
C
Input current noise (each input)
f > 200 kHz
2.0
pA/√ Hz
C
Output impedance
f = 20 MHz
0.9
Ω
C
C
5
ns
C
ns
C
dBc
C
DC PERFORMANCE (5)
Differential to single-ended gain
±100-mV output
Differential to single-ended gain drift
TJ = –40°C to +125°C
VREF input pin gain
Differential inputs = 0 V,
VREF = ±100 mV
VREF input pin gain drift
TJ = –40°C to +125°C
Output offset voltage
Output offset voltage drift
Input bias current – each
input(3)
Input bias current drift
Input offset current
Input offset current drift
1.975
0.975
2.0
2.025
37
43
V/V
A
ppm/°C
B
1.0
1.015
V/V
A
–67
±8
–74
ppm/°C
B
35
mV
A
TJ ≈ 25°C
–35
TJ = 0°C to 70°C
–37
36
mV
B
TJ = –40°C to +125°C
–39
38
mV
B
TJ = –40°C to +125°C
–4
–25
–45
µV/°C
B
TJ ≈ 25°C
–4
±2
4
µA
A
TJ = 0°C to 70°C
–4.2
4.3
µA
B
TJ = –40°C to +125°C
–4.3
4.5
µA
B
TJ = –40°C to +125°C
3
4
5
nA/°C
B
TJ ≈ 25°C
–400
±50
400
nA
A
TJ = 0°C to 70°C
–475
535
nA
B
TJ = –40°C to +125°C
–595
700
nA
B
TJ = –40°C to +125°C
–3
nA/°C
B
0.2
3
1.8
1.9
V
A
2.0
V
B
1.4
V
A
1.5
V
B
INPUTS(4)
Common-mode input negative supply
headroom
TJ ≈ 25°C
Common-mode input positive supply
headroom
TJ ≈ 25°C
Common-mode rejection ratio (CMRR)
–1 V ≤ VIC ≤ 3 V
dB
A
Input impedance differential mode
VCM = 0 V
20 || 2.3
kΩ || pF
C
Input impedance common mode
VCM = 0 V
20 || 2.3
kΩ || pF
C
1.75
V
A
1.95
V
B
TJ = –40°C to +85°C
1.3
TJ = –40°C to +125°C
42
48
OUTPUT(6)
Output voltage headroom to either supply
6
TJ ≈ 25°C
TJ = –40°C to +85°C
Submit Document Feedback
1.4
1.5
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.5 Electrical Characteristics: D2S (continued)
at +VCC = 6.0 V, –VCC = –6.0 V, AV = 2 V/V, 25-Ω source impedance, input common-mode voltage (VIC) = 0.25 V, external
OPS input selected (PATHSEL ≥ 1.3 V), VREF = GND, RLOAD = 100 Ω, and TJ ≈ 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Output current drive
±0.8 VPP, RLOAD = 20 Ω
DC output impedance
Load current = ±20 mA
MAX
UNIT
TEST
LEVEL
MIN
TYP
±35
±45
mA
A
0.3
Ω
C
mA
A
8
µA/°C
C
(1)
POWER SUPPLY (D2S + Midsupply Buffer Only; OPS Disabled: DISABLE pin ≥ 1.3 V)
Supply current
±6-V supplies
20.2
Supply current temperature coefficient
(1)
(2)
(3)
(4)
(5)
(6)
21.3
26
Positive power-supply rejection ratio
(+PSRR)
Referred to input
62
71
dB
A
Negative power-supply rejection ratio (–
PSRR)
Referred to input
61
71
dB
A
Test levels (all values set by characterization and simulation): (A) 100% tested at TA≈ TJ≈ 25°C; over temperature limits by
characterization and simulation. (B) Not tested in production; limits set by characterization and simulation. (C) Typical value only
for information. DC limits tested with no self-heating. Add internal self heating to TA for TJ.
This slew rate is the average of the rising and falling time estimated from the large-signal bandwidth as: (Vpeak / √ 2) × 2π × f–3dB.
Currents out of pin treated as a positive polarity.
Applies to input pins 2 (IN+) and 3 (IN–).
Output measured at pin 6.
Output measured at pin 6.
6.6 Electrical Characteristics: OPS
at +VCC = 6.0 V, –VCC = –6.0 V, 25-Ω D2S source impedance, D2S input common-mode voltage (VIC) = 0.25 V, VREF = GND,
RF = 249 Ω(1), RG = 162 Ω, AV = 2.5 V/V, OPS RLOAD = 100 Ω, OPS enabled (DISABLE ≤ 0.7 V or floated), external OPS
input selected (PATHSEL ≥ 1.3 V), and TJ ≈ 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TEST
LEVEL
(2)
AC PERFORMANCE (4)
Small-signal bandwidth (SSBW)
VOUT = 100 mVPP, peaking < 2.0 dB
700
MHz
C
Large-signal bandwidth (LSBW)
VOUT = 5 VPP
270
MHz
C
Bandwidth for 0.2-dB flatness
VOUT = 5 VPP
110
MHz
C
Slew rate(3)
VOUT = 5-V step
3000
V/µs
C
Overshoot and undershoot
Input tr = 1 ns, VOUT = 5-V step
4%
Rise and fall time
Input tr = 1 ns, VOUT = 5-V step
1.7
Settling time to 0.1%
Input tr = 1 ns, VOUT = 5-V step
2nd-order harmonic distortion (HD2)
f = 20 MHz, VOUT= 5 VPP
3rd-order harmonic distortion (HD3)
f = 20 MHz, VOUT= 5 VPP
Noninverting input voltage noise
f > 200 kHz
Noninverting input current noise
Inverting input current noise
Closed-loop ac output impedance
C
ns
C
25
ns
C
–66
dBc
C
–68
dBc
C
2.7
nV/√ Hz
C
f > 200 kHz
1.3
pA/√ Hz
C
f > 200 kHz
18
pA/√ Hz
C
f = 20 MHz
0.25
Ω
C
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
7
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.6 Electrical Characteristics: OPS (continued)
at +VCC = 6.0 V, –VCC = –6.0 V, 25-Ω D2S source impedance, D2S input common-mode voltage (VIC) = 0.25 V, VREF = GND,
RF = 249 Ω(1), RG = 162 Ω, AV = 2.5 V/V, OPS RLOAD = 100 Ω, OPS enabled (DISABLE ≤ 0.7 V or floated), external OPS
input selected (PATHSEL ≥ 1.3 V), and TJ ≈ 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
800
1700
2.495
2.515
TJ ≈ 25°C
–12
±2.5
TJ = 0°C to 70°C
–13
TJ = –40°C to +125°C
–14.1
TJ = –40°C to +125°C
–3
–12
–15
±2.5
UNIT
TEST
LEVEL
kΩ
A
2.53
V/V
A
12
mV
A
12.5
mV
B
13.7
mV
B
–21
µV/°C
B
MAX
(2)
DC PERFORMANCE (4)
Open-loop transimpedance gain(1)
VOUT = ±1 V, RLOAD= 500-Ω
Closed-loop gain
0.1% external RF and RG resistors
INPUT
External input offset voltage
(pin 9 to pin 12)
External input offset voltage drift
(pin 9 to pin 12)
Internal input offset voltage
(pin 6 to pin 12)
Internal input offset voltage drift
(pin 6 to pin 12)
TJ ≈ 25°C
15
mV
A
TJ = 0°C to 70°C
–15.7
15.4
mV
B
TJ = –40°C to +125°C
–16.6
16
mV
B
TJ = –40°C to +125°C
–3
–10
–16
µV/°C
B
–7
±1.2
7
mV
C
–5
±5
15
µA
A
External to internal input offset voltage
match
External noninverting input bias current
(pin 9)(5)
External noninverting input bias current
drift (pin 9)
Inverting input bias current – either input
selected(5)
Inverting input bias current drift
TJ ≈ 25°C
TJ = 0°C to 70°C
–5
15.2
µA
B
TJ = –40°C to +125°C
–5.2
15.4
µA
B
TJ = –40°C to +125°C
0
2
3.3
nA/°C
B
–75
±5
75
µA
A
TJ ≈ 25°C
TJ = 0°C to 70°C
–39
37
µA
B
TJ = –40°C to +125°C
–43.5
40.5
µA
B
TJ = –40°C to +125°C
–15
–50
–85
nA/°C
B
2.6
3.0
V
A
dB
A
22.4
kΩ
A
Input headroom to either supply
Common-mode rejection ratio (CMRR)
±3.4-V input range
Noninverting input resistance
45
53
16
18.5
Noninverting input capacitance
3.3
pF
C
Open-loop inverting input impedance
74
Ω
C
1.6
V
A
1.8
V
B
OUTPUT(6)
RLOAD = 500 Ω, TJ ≈ 25°C
8
1.3
1.4
Output voltage headroom to either supply
RLOAD = 500 Ω, TJ = –40°C to
+125°C
Linear output current
±1.7 V into 20-Ω RLOAD
75
90
mA
A
Peak output current
±2.6-V into 20-Ω RLOAD
120
140
mA
A
DC output impedance
0-V output, load current = ±40 mA
Ω
C
Internal feedback resistor, RF
Between pins 11 and 12
kΩ
A
Submit Document Feedback
0.05
16
18.5
22.4
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.6 Electrical Characteristics: OPS (continued)
at +VCC = 6.0 V, –VCC = –6.0 V, 25-Ω D2S source impedance, D2S input common-mode voltage (VIC) = 0.25 V, VREF = GND,
RF = 249 Ω(1), RG = 162 Ω, AV = 2.5 V/V, OPS RLOAD = 100 Ω, OPS enabled (DISABLE ≤ 0.7 V or floated), external OPS
input selected (PATHSEL ≥ 1.3 V), and TJ ≈ 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
0.7
0.9
UNIT
TEST
LEVEL
V
A
1.3
V
A
+VCC
V
A
MAX
(2)
PATHSEL (Pin 4; Logic Reference = Pin 7 = GND)
Input low logic level
Internal path selected
Input high logic level
External input selected at VIN pin
Input voltage range
PATHSEL voltage when floated
Input pin bias current(7)
0.9
–0.5
Internal input from D2S selected
0
40
mV
A
0-V input
0
15
µA
A
–150
–250
µA
A
3.3-V input
Input pin impedance
20
18 || 1.5
kΩ || pF
C
80
ns
C
50
mV
C
80
dB
A
55
65
dB
C
0.7
0.9
V
A
V
A
Switching time
To 1% of final value
Input switching glitch
Both inputs at GND
Deselected input dc isolation
± 2-V input
70
Deselected input ac isolation
2 VPP, at 20-MHz input
DISABLE (Pin 10; Logic Reference = Pin 7 = GND)
Input low logic level
Input high logic level
0.9
Shutdown control voltage range
Shutdown voltage when floated
Input pin bias current(7)
–0.5
Output stage enabled
0-V input
3.3-V input
1.3
V
B
40
mV
A
0
4
µA
A
–150
–250
µA
A
0
Input pin impedance
+VCC
20
18 || 1.5
kΩ || pF
C
200
ns
C
70
80
dB
A
55
65
dB
C
9.6
10.8
12
mA
A
2
2.9
mA
B
280
380
µA
A
60
dB
A
56
dB
A
Switching time (turn on or off)
To 10% of final value
Shutdown dc isolation (either input)
±2-V input
Shutdown ac isolation (either input)
2 VPP at 20-MHz input
Supply current (OPS only)
±6-V supplies
Disabled supply current in OPS
±6-V supplies
1.5
Logic reference current at pin 7(7)
Pins 4, 7, and 10 held at 0 V
200
Positive power-supply rejection ratio
(+PSRR)
Referred to input
55
Negative power-supply rejection ratio (–
PSRR)
Referred to input
53
POWER SUPPLY
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Output power stage includes an internal 18.5-kΩ feedback resistor. This internal resistor, in parallel with an external 249-Ω RF and
162-Ω RG, results in a gain of 2.5 V/V after including a nominal gain loss of 0.9935 V/V due to the input buffer and loop-gain effects.
Test levels (all values set by characterization and simulation): (A) 100% tested at TA≈ TJ≈ 25°C; over temperature limits by
characterization and simulation. (B) Not tested in production; limits set by characterization and simulation. (C) Typical value only
for information. DC limits tested with no self-heating. Add internal self heating to TA for TJ.
This slew rate is the average of the rising and falling time estimated from the large-signal bandwidth as: (Vpeak / √ 2) × 2π × f–3dB.
Output measured at pin 11.
Currents out of pin treated as a positive polarity.
Output measured at pin 11.
Currents out of pin treated as a positive polarity.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
9
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.7 Electrical Characteristics: D2S + OPS
at +VCC = 6.0 V, –VCC = –6.0 V, 25-Ω D2S source impedance, D2S input VIC = 0.25 V, internal path selected to OPS
(PATHSEL ≤ 0.7 V or floated), VREF = GND, combined AV = 5 V/V, D2S RLOAD= 200 Ω, RF = 249 Ω(1), RG = 162 Ω (OPS AV =
2.5 V/V), OPS enabled (DISABLE ≤ 0.7 V or floated), OPS RLOAD = 100 Ω, and TJ ≈ 25°C (unless otherwise noted)
PARAMETER
AC
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TEST
LEVEL
(2)
PERFORMANCE(4)
Small-signal bandwidth (SSBW)
VOUT = 100 mVPP, peaking < 1.5 dB
650
MHz
C
Large-signal bandwidth (LSBW)
VOUT = 5 VPP
270
MHz
C
Bandwidth for 0.2-dB flatness
VOUT = 2 VPP
110
MHz
C
3000
V/µs
C
Slew
rate(3)
VOUT = 8-V step
Overshoot and undershoot
Input tr = 1 ns, VOUT = 5-V step
4%
C
Rise and fall time
Input tr = 1 ns, VOUT = 5-V step
1.7
ns
C
Settling time to 0.1%
Input tr = 1 ns, VOUT = 5-V step
25
ns
C
2nd-order harmonic distortion (HD2)
f = 20 MHz, VOUT= 5 VPP
–66
dBc
C
3rd-order harmonic distortion (HD3)
f = 20 MHz, VOUT= 5 VPP
–68
dBc
C
Output voltage noise
f > 200 kHz, AV = 5 V/V
33
nV/√ Hz
C
DC PERFORMANCE(4)
Total gain D2S to OPS output(1)
0.1% tolerance external resistors, dc,
±100-mV output test
4.92
5.02
5.12
V/V
A
32.7
34.5
39
mA
A
µA/°C
C
POWER SUPPLY (Combined D2S, OPS, and Midscale Reference Buffer)
(1)
(2)
(3)
(4)
10
Supply current
±6-V supplies
Supply current temperature
coefficient
TJ = 0°C to 100°C
±5
Output power stage includes an internal 18.5-kΩ feedback resistor. This internal resistor, in parallel with an external 249-Ω RF and
162-Ω RG, results in a gain of 2.5 V/V after including a nominal gain loss of 0.9935 V/V due to the input buffer and loop-gain effects.
Test levels (all values set by characterization and simulation): (A) 100% tested at TA≈ TJ≈ 25°C; over temperature limits by
characterization and simulation. (B) Not tested in production; limits set by characterization and simulation. (C) Typical value only
for information.
This slew rate is the average of the rising and falling time estimated from the large-signal bandwidth as: (Vpeak / √ 2) × 2π × f–3dB.
Output measured at pin 11.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.8 Electrical Characteristics: Midscale (DC) Reference Buffer
at +VCC = 6.0 V, –VCC = –6.0 V, RLOAD = 150 Ω at pin 15, and TJ ≈ 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
UNIT
TEST
LEVEL
200
MHz
C
50
MHz
C
TYP
MAX
(1)
AC PERFORMANCE (Output measured at pin 15)
Small-signal bandwidth (SSBW)
VOUT = 100 mVPP
Large-signal bandwidth (LSBW)
VOUT = 1 VPP
Slew
rate(2)
VOUT = 4-V step
110
V/µs
C
Input voltage noise
f > 5 kHz
4.6
nV/√ Hz
C
Input current noise
f > 5 kHz
1.3
pA/√ Hz
C
AC output impedance
f = 20 MHz, no load current
2.5
Ω
C
DC AND I/O PERFORMANCE (RS = 25 Ω, and output measured at pin 15, unless otherwise noted)
Buffer gain
VI = ±1 V, RLOAD = 200 Ω
Buffer gain drift
TJ = –40°C to +125°C
Output offset from midsupply
Input floating, pin 1 open
–120
Output offset voltage
Input driven to 0 V from 0-Ω source
Input offset voltage drift
TJ = –40°C to +125°C, input driven
to 0 V
Input bias current(3)
(1)
(2)
(3)
.9985
0.999
1.001
V/V
A
–1.2
–2.2
ppm/°C
B
30
70
mV
A
–1.0
4.0
15
mV
A
4
9
15
µV/°C
B
–10
±1
10
µA
A
–5
±1
5
nA/°C
B
1.1
1.4
V
A
kΩ || pF
C
65
mA
A
0.3
Ω
C
Input bias current drift
TJ = –40°C to +125°C
Input/output headroom to either
supply
gain change < 1%
Input impedance
Internal 50-kΩ divider resistors to
each supply
Linear output current into resistive
load
±1.62 V into 36 Ω
DC output impedance
Load current = ±30 mA
Positive power-supply rejection ratio
(+PSRR)
Referred to input with VMID_IN (pin
1) at GND
60
dB
A
Negative power-supply rejection ratio Referred to input with VMID_IN (pin
(—PSRR)
1) at GND
69
dB
A
22 || 1.5
40
Test levels (all values set by characterization and simulation): (A) 100% tested at TA≈ TJ≈ 25°C; over temperature limits by
characterization and simulation. (B) Not tested in production; limits set by characterization and simulation. (C) Typical value only
for information.
This slew rate is the average of the rising and falling time estimated from the large-signal bandwidth as: (VPEAK / √ 2) × 2π × f–3dB.
Currents out of pin treated as a positive polarity.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
11
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.9 Typical Characteristics: D2S + OPS
17
4
15
3
13
2
Output Voltage (V)
Gain (dB)
at +VCC = 6 V, –VCC = –6 V, 25-Ω D2S source impedance , VIC = 0.25 V, internal path selected (PATHSEL = GND), VREF =
GND, D2S RLOAD = 200 Ω at pin 6, RF = 249 Ω, RG = 162 Ω, OPS AV = 2.5 V/V, OPS On (DISABLE = GND), OPS RLOAD =
100 Ω at pin 11, and TJ ≈ 25°C (unless otherwise noted)
11
9
7
0.5 Vpp
1 Vpp
2 Vpp
5 Vpp
8 Vpp
5
3
1
10M
0
-1
-2
500 mVPP
5 VPP
-3
-4
100M
Frequency (Hz)
1G
Time (20ns/div.)
D001
D002
Figure 6-1. Frequency Response vs Output Voltage
Figure 6-2. Small- and Large-Signal Step Response
-20
-20
-30
-30
-40
Distortion (dBc)
-40
Distortion (dBc)
1
-50
-60
-70
-80
-100
1M
10M
Test Frequency (Hz)
-60
-70
-80
-90
2 VPP
5 VPP
8 VPP
-90
-50
2 VPP
5 VPP
8 VPP
-100
-110
1M
100M
5.05
Input Voltage Noise (nV/—Hz)
D2S + OPS Gain (V/V)
D004
100
5.04
5.03
5.02
5.01
5
4.99
-35
-15
5
25
45
65
Junction Temperature (qC)
85
30 units shown
Figure 6-5. Gain vs Temperature
12
100M
Figure 6-4. HD3 vs Frequency
Figure 6-3. HD2 vs Frequency
4.98
-55
10M
Test Frequency (Hz)
D003
105
125
10
1
100
D005
1k
10k
100k
1M
Frequency (Hz)
10M
100M
D006
25-Ω source impedance on each D2S input
Figure 6-6. Input-Referred Differential Noise
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.9 Typical Characteristics: D2S + OPS (continued)
at +VCC = 6 V, –VCC = –6 V, 25-Ω D2S source impedance , VIC = 0.25 V, internal path selected (PATHSEL = GND), VREF =
GND, D2S RLOAD = 200 Ω at pin 6, RF = 249 Ω, RG = 162 Ω, OPS AV = 2.5 V/V, OPS On (DISABLE = GND), OPS RLOAD =
100 Ω at pin 11, and TJ ≈ 25°C (unless otherwise noted)
3
1
2
0
Normalized Gain (dB)
Normalized Gain (dB)
1
0
-1
-2
-3
-4
3 V/V
5 V/V
10 V/V
20 V/V
-5
-6
-7
1M
-1
-2
-3
-4
-5
3 V/V
5 V/V
10 V/V
20 V/V
-6
10M
100M
Frequency (Hz)
-7
1M
1G
VOUT = 500 mVPP, see Table 8-1
-30
-30
-40
-40
Distortion (dBc)
Distortion (dBc)
-20
-50
-60
-70
10M
Frequency (Hz)
-60
-70
3 V/V
5 V/V
10 V/V
20 V/V
-90
-100
1M
100M
10M
Frequency (Hz)
D009
VOUT = 5 VPP, see Table 8-1
100M
D010
VOUT = 5 VPP, see Table 8-1
Figure 6-9. HD2 vs Gain
Figure 6-10. HD3 vs Gain
-40
-20
1 VPP
2 VPP
5 VPP
8 VPP
-30
-50
-40
-60
Distortion (dBc)
Distortion (dBc)
D008
-50
-80
3 V/V
5 V/V
10 V/V
20 V/V
-100
1M
1G
Figure 6-8. Large-Signal Frequency Response vs Gain
-20
-90
100M
Frequency (Hz)
VOUT = 5 VPP, see Table 8-1
Figure 6-7. Small-Signal Frequency Response vs Gain
-80
10M
D007
-70
-80
9
10
11
12
13
14
Total Balanced Supply Voltage (V)
15
-70
-90
-100
-100
8
-60
-80
1 VPP
2 VPP
5 VPP
8 VPP
-90
-50
16
8
D011
9
10
11
12
13
14
Total Balanced Supply Voltage (V)
15
16
D012
Test frequency = 20 MHz
Test frequency = 20 MHz
Figure 6-12. HD3 vs Supply Voltage
Figure 6-11. HD2 vs Supply Voltage
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
13
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.10 Typical Characteristics: D2S Only
7
7
6
6
5
5
4
4
Gain (dB)
Gain (dB)
at +VCC = 6.0 V, –VCC = –6.0 V, fixed gain of 2 V/V, 25-Ω D2S source impedance, VIC = 0.25 V, external path selected
(PATHSEL = +VCC), VREF = GND, D2S RLOAD = 100 Ω at pin 6, and TJ ≈ 25°C (unless otherwise noted)
3
2
1
0
-1
-2
1M
2
1
VCM = -1 V
VCM = 0 V
VCM = 0.25 V
VCM = 1 V
VCM = 2 V
10M
3
50 :
100 :
200 :
500 :
0
-1
100M
Frequency (Hz)
-2
1M
1G
10M
D013
VOUT = 250 mVPP
-30
-30
-40
-40
Distortion (dBc)
Distortion (dBc)
-20
-50
-60
-70
-80
-50
-60
-70
-80
1 VPP
2 VPP
4 VPP
-90
-100
1M
10M
Frequency (Hz)
-100
1M
100M
100M
D016
Figure 6-16. HD3 vs Output Voltage
100
Differential Input Noise (nV/—Hz)
Input Referred CMRR (dB)
10M
Frequency (Hz)
D015
50
45
40
VCM = -1 V
VCM = 0 V
VCM = 0.25 V
VCM = 1 V
VCM = 2 V
VCM = 3 V
10M
Frequency (Hz)
100M
RS = 0 :
RS = 25 :
RS = 100 :
RS = 1 k:
10
1
100
D017
Figure 6-17. Common-Mode Rejection Ratio vs Input CommonMode Voltage
14
1 VPP
2 VPP
4 VPP
-90
Figure 6-15. HD2 vs Output Voltage
25
1M
D014
Figure 6-14. Frequency Response vs Load Resistance
-20
30
1G
VOUT = 2 VPP
Figure 6-13. Frequency Response vs Input Common-Mode
Voltage
35
100M
Frequency (Hz)
1k
10k
100k
1M
Frequency (Hz)
10M
100M
D018
Figure 6-18. Differential Input Noise vs Source Impedance
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.10 Typical Characteristics: D2S Only (continued)
at +VCC = 6.0 V, –VCC = –6.0 V, fixed gain of 2 V/V, 25-Ω D2S source impedance, VIC = 0.25 V, external path selected
(PATHSEL = +VCC), VREF = GND, D2S RLOAD = 100 Ω at pin 6, and TJ ≈ 25°C (unless otherwise noted)
10
12
Output Impedance (:)
D2S Output Offset Voltage (mV)
14
10
8
6
4
1
r4 V
r5 V
r6 V
r7.5 V
2
0
-55
-35
-15
5
25
45
65
Junction Temperature (qC)
85
105
0.1
100k
125
1M
10M
100M
Frequency (Hz)
D019
D020
Figure 6-20. Output Impedance vs Supply Voltage
30 units shown
Figure 6-19. Output DC Offset Voltage vs Die Temperature
1.5
1.1
100 :
200 :
500 :
1.05
Output Voltage (V)
Output Voltage (V)
1
0.5
0
-0.5
1
0.95
0.9
100 :
200 :
500 :
0.85
-1
0.8
-1.5
Time (5 ns/div)
Time (20 ns/div)
D022
D021
±1-V output pulse
±1-V output pulse
Figure 6-21. Large-Signal Step Response vs Load Resistance
Figure 6-22. Large-Signal Pulse Settling Response vs Load
Resistance
1
70
65
0
60
PSRR (dB)
Gain (dB)
-1
-2
-3
0.1 Vpp
0.25 Vpp
0.5 Vpp
1 Vpp
2 Vpp
-4
-5
1M
55
50
45
40
35
10M
100M
Frequency (Hz)
1G
30
10k
Figure 6-23. VREF Input Pin Frequency Response
100k
1M
Frequency (Hz)
D023
25-Ω D2S source impedance on each input
VCM = -1 V, PSRR+
VCM = -1 V, PSRRVCM = 0 V, PSRR+
VCM = 0 V, PSRRVCM = 3 V, PSRR+
VCM = 3 V, PSRR10M
D024
Figure 6-24. Simulated Power-Supply Rejection Ratio vs Input
Common-Mode Voltage
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
15
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.11 Typical Characteristics: OPS Only
at +VCC = 6.0 V, –VCC = –6.0 V, 25-Ω D2S source impedance, VREF = GND, RF = 249 Ω, RG = 162 Ω, OPS AV = 2.5V/V, OPS
RLOAD = 100 Ω at pin 11, OPS enabled (DISABLE = GND), external input path selected (PATHSEL = +VCC), and TJ ≈ 25°C
(unless otherwise noted)
6
Normalized Gain (dB)
Normalized Gain (dB)
4
2
AV = 1.5 V/V
AV = 2.5 V/V
AV = 5 V/V
AV = 10 V/V
2
0
-2
0
-2
-4
-4
-6
1M
10M
100M
Frequency (Hz)
-6
1M
1G
8
8
Inverting Response (dB)
Output Response (dB)
10
6
4
2
0.5 VPP
2 VPP
5 VPP
6 VPP
D026
6
4
2
0.5 VPP
2 VPP
5 VPP
6 VPP
0
100M
Frequency (Hz)
1G
Figure 6-26. Frequency Response vs Inverting Gain
10
10M
100M
Frequency (Hz)
VOUT = 100 mVPP, see Table 8-3 for RF values vs gain
Figure 6-25. Frequency Response vs Noninverting Gain
-2
1M
10M
D025
VOUT = 100 mVPP, see Table 8-1 for RF values vs gain
0
AV = -1 V/V
AV = -2.5 V/V
AV = -5 V/V
AV = -10 V/V
-2
1M
1G
10M
D027
Figure 6-27. Noninverting Response vs Output Voltage
100M
Frequency (Hz)
1G
D028
AV = –2.5 V/V, see Table 8-3 for RF value
Figure 6-28. Inverting Response vs Output Voltage
3
3.5
500 mVPP
5 VPP
2
1.5
Output Voltage (V)
Output Voltage (V)
2.5
0.5
-0.5
-1.5
-2.5
1
0
-1
-2
500 mVPP
5 VPP
-3.5
-3
Time (10ns/div.)
Time (10ns/div.)
D029
Figure 6-29. Noninverting Step Response
D030
AV = –2.5 V/V, see Table 8-3 for RF value
Figure 6-30. Inverting Step Response
16
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.11 Typical Characteristics: OPS Only (continued)
at +VCC = 6.0 V, –VCC = –6.0 V, 25-Ω D2S source impedance, VREF = GND, RF = 249 Ω, RG = 162 Ω, OPS AV = 2.5V/V, OPS
RLOAD = 100 Ω at pin 11, OPS enabled (DISABLE = GND), external input path selected (PATHSEL = +VCC), and TJ ≈ 25°C
(unless otherwise noted)
-25
Distortion (dBc)
-45
-45
-55
-65
-75
-55
-65
-75
-85
-85
-95
-95
-105
1M
1 VPP
2 VPP
5 VPP
8 VPP
-35
Distortion (dBc)
-35
-25
1 VPP
2 VPP
5 VPP
8 VPP
10M
Frequency (Hz)
-105
1M
100M
10M
Frequency (Hz)
D031
-35
-35
100 :
200 :
500 :
-55
Distortion (dBc)
Distortion (dBc)
100 :
200 :
500 :
-45
-55
-65
-75
-65
-75
-85
-85
-95
-95
-105
1M
10M
Frequency (Hz)
-105
1M
100M
10M
Frequency (Hz)
D033
-25
-35
-45
Distortion (dBc)
Distortion (dBc)
-25
±4 V
±5 V
±6 V
±7.5 V
-55
-65
-75
-65
-75
-85
-95
-95
10M
Frequency (Hz)
100M
±4 V
±5 V
±6 V
±7.5 V
-55
-85
-105
1M
D034
Figure 6-34. HD3 vs Load Resistance
Figure 6-33. HD2 vs Load Resistance
-45
100M
VOUT = 5 VPP
VOUT = 5 VPP
-35
D032
Figure 6-32. HD3 vs Output Voltage
Figure 6-31. HD2 vs Output Voltage
-45
100M
-105
1M
D035
VOUT = 5 VPP
10M
Frequency (Hz)
100M
D036
VOUT = 5 VPP
Figure 6-35. HD2 vs Supply Voltage
Figure 6-36. HD3 vs Supply Voltage
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
17
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.11 Typical Characteristics: OPS Only (continued)
at +VCC = 6.0 V, –VCC = –6.0 V, 25-Ω D2S source impedance, VREF = GND, RF = 249 Ω, RG = 162 Ω, OPS AV = 2.5V/V, OPS
RLOAD = 100 Ω at pin 11, OPS enabled (DISABLE = GND), external input path selected (PATHSEL = +VCC), and TJ ≈ 25°C
(unless otherwise noted)
-30
-30
0.25 VPP
1 VPP
2.5 VPP
4 VPP
-40
-50
IMD3 (dBc)
IMD2 (dBc)
-50
-60
-60
-70
-70
-80
-80
-90
-90
1
10
Center Frequency (MHz)
100
1
10
Center Frequency (MHz)
D037
±100-kHz tone separation, output voltage for each tone
100
D038
±100-kHz tone separation, output voltage for each tone
Figure 6-37. Second-Order Intermodulation Distortion vs Output
Voltage
Figure 6-38. Third-Order Intermodulation Distortion vs Output
Voltage
5
1000
Voltage Noise
Noninverting Current Noise
Inverting Current Noise
4
3
Output Voltage (V)
Voltage (nV/—Hz) and Current Noise (pA/—Hz)
0.25 VPP
1 VPP
2.5 VPP
4 VPP
-40
100
10
2
1
0
-1
-2
-3
-4
1
100
1k
10k
100k
Frequency (Hz)
1M
-5
10
10M
100
Load Resistance (:)
D039
Figure 6-39. Input-Referred Spot Noise vs Frequency
1k
D040
Output swing with better than 0.1% linearity
Figure 6-40. Linear Output Swing vs Load Resistance
12
11.8
Input/Output Voltage (V)
Supply Current (mA)
11.4
11
10.6
10.2
9.8
-55
4
0
-4
-8
-35
-15
5
25
45
65
Junction Temperature (0C)
85
105
125
-12
0
1
2
3
4
Time (Ps)
D041
30 units shown
5
D042
±4.5-V input triangular wave, OPS AV = –2.5 V/V
Figure 6-41. Quiescent Supply Current vs Temperature
18
Measured VOUT
Ideal VOUT
8
Figure 6-42. Output Overdrive Response
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.11 Typical Characteristics: OPS Only (continued)
at +VCC = 6.0 V, –VCC = –6.0 V, 25-Ω D2S source impedance, VREF = GND, RF = 249 Ω, RG = 162 Ω, OPS AV = 2.5V/V, OPS
RLOAD = 100 Ω at pin 11, OPS enabled (DISABLE = GND), external input path selected (PATHSEL = +VCC), and TJ ≈ 25°C
(unless otherwise noted)
50
10
AV = 2.5 V/V
AV = 5 V/V
AV = 10 V/V
40
9
8
Normalized Gain (dB)
Series Output Resistance (:)
45
35
30
25
20
15
7
6
4
3
10
2
5
1
0
1
10
100
Load Capacitance (pF)
0 pF
4.7 pF
10 pF
22 pF
47 pF
100 pF
220 pF
470 pF
1nF
5
0
1M
1k
10M
D043
See Table 8-6 for RF values vs OPS gain
Figure 6-43. Series Output Resistance vs Load Capacitance
100M
Frequency (Hz)
1G
D044
VOUT = 500 mVPP, see Series Output Resistance vs Load
Capacitance for RS value
Figure 6-44. Frequency Response vs Load Capacitance
-20
-20
Distortion (dBc)
-40
-40
-50
-60
-70
-50
-60
-70
-80
-80
-90
-90
1M
10M
-100
1M
20M
Frequency (Hz)
10M
20M
Frequency (Hz)
D045
±VCC = ±7.5 V, RF = 158 Ω, AV = 5 V/V, VOUT = 10 VPP, see
Series Output Resistance vs Load Capacitance for RS value
D046
±VCC = ±7.5 V, RF = 158 Ω, AV = 5 V/V, VOUT = 10 VPP, see
Series Output Resistance vs Load Capacitance for RS value
Figure 6-46. HD3 vs Load Capacitance
Figure 6-45. HD2 vs Load Capacitance
6
6
2 VPP
10 VPP
4
Voltage at Load Capacitor (V)
Voltage at Load Capacitor (V)
47 pF
100 pF
220 pF
330 pF
-30
Distortion (dBc)
-30
47 pF
100 pF
220 pF
330 pF
2
0
-2
-4
-6
2 VPP
10 VPP
4
2
0
-2
-4
-6
Time (50 ns/div.)
Time (50 ns/div)
D047
±VCC = ±7.5 V, CLOAD = 100 pF, RF = 158 Ω, AV = 5 V/V, see
Series Output Resistance vs Load Capacitance for RS value
D048
±VCC = ±7.5 V, CLOAD = 150 pF, RF = 158 Ω, AV = 5 V/V, see
Series Output Resistance vs Load Capacitance for RS value.
Figure 6-47. Pulse Response
Figure 6-48. Pulse Response
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
19
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.12 Typical Characteristics: Midscale (DC) Reference Buffer
at +VCC = 6.0 V, –VCC = –6.0 V, RLOAD = 150 Ω, and TJ ≈ 25°C (unless otherwise noted)
1
0.6
100 mVPP
1 VPP
0
0.4
Output Voltage (V)
-1
Gain (dB)
-2
-3
-4
-5
-6
0.2
0
-0.2
-0.4
0.1VPP
1.0VPP
-7
-8
1M
-0.6
10M
100M
Frequency (Hz)
Time (20 ns/div)
700M
D050
D049
Figure 6-50. Step Response
Figure 6-49. Frequency Response vs Output Voltage
60
100
IO = 0 mA
IO = -20 mA
IO = 20 mA
Buffer Offset Voltage (mV)
50
Output Impedance (:)
10
1
0.1
40
GND I/P, ILOAD= 0 mA
GND I/P, ILOAD= -20 mA
GND I/P, ILOAD= 20 mA
Float I/P, ILOAD= 0 mA
Float I/P, ILOAD= -20 mA
Float I/P, ILOAD= 20 mA
30
20
10
0
0.01
100k
1M
10M
-10
-40
100M
Frequency (Hz)
Figure 6-51. Buffer Output Impedance vs Load Current
20
40
60
80
Junction Temperature (qC)
100
120
D052
3
6
0
5
Buffer Gain (dB)
Series Output Resistance (:)
0
Figure 6-52. Buffer Output Offset vs Load Current (ILOAD)
7
4
3
-3
-6
2
-9
1
0
1
10
Load Capacitance (nF)
100
-12
1M
D053
RLOAD = 150 Ω in parallel with CLOAD, see the Section 7.8
section for circuit setup
Figure 6-53. Series Resistance vs Capacitive Load
20
-20
D051
No Cap
1 nF
10 nF
100 nF
10M
Frequency (Hz)
100M
500M
D054
VOUT = 100 mVPP, RLOAD = 150 Ω in parallel with CLOAD, see
Section 7.8 for circuit setup
Figure 6-54. Frequency Response vs Capacitive Load
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.13 Typical Characteristics: Switching Performance
3.5
DISABLE Input and OPS Output Voltage (V)
PATHSEL Input and OPS Output Voltage (V)
at +VCC = 6 V, –VCC = –6 V, 25-Ω D2S source impedance , VIC = 0.25 V, internal path selected (PATHSEL = GND), VREF =
GND, D2S RLOAD = 200 Ω at pin 6, RF = 249 Ω, RG = 162 Ω, OPS On (DISABLE = GND), OPS RLOAD = 100 Ω at pin 11, and
TJ ≈ 25°C (unless otherwise noted)
3
2.5
2
1.5
1
0.5
PATHSEL In
OPS VOUT
0
-0.5
3.5
3
2.5
2
1.5
1
0.5
0
-0.5
DISABLE In
OPS VOUT
-1
-1.5
Time (100 ns/div.)
Time (100 ns/div.)
D055
D2S Inputs: IN+ = IN– = GND, OPS input: VIN+ = 1 V
D056
PATHSEL = high, OPS input: VIN+ = 1 VPP , 10-MHz sine
wave
Figure 6-55. PATHSEL Switching Time
Figure 6-56. OPS Enable and Disable Time
-20
Feedthrough (dBc)
-40
-50
-60
-70
-80
10M
100M
Frequency (Hz)
-60
10M
100M
Frequency (Hz)
1G
D058
Figure 6-58. OPS Reverse Feedthrough in Disable
DISABLE Input and OPS Output Voltage (V)
PATHSEL Input and OPS Output Voltage (V)
-50
D057
3
2.5
2
1.5
1
0
-40
-80
1M
1G
Figure 6-57. OPS Forward Feedthrough in Disable
0.5
-30
-70
-90
-100
1M
Int Path, OPS A V = 2.5 V/V
Ext Path, OPS A V = 2.5 V/V
-20
Feedthrough (dBc)
-30
-10
Ext Path, OPS A V = 2.5 V/V
Ext Path, OPS A V = 10 V/V
Int Path, OPS A V = 2.5 V/V
Int Path, OPS A V = 10 V/V
PATHSEL In
r5-V supply
r6-V supply
r7.5-V supply
-0.5
3.5
3
2.5
2
DISABLE In
r5-V supply
r6-V supply
r7.5-V supply
1.5
1
0.5
0
-0.5
Time (1 Ps/div.)
Time (1 Ps/div.)
D059
D2S inputs: IN+ = IN– = GND, OPS input: VIN+ = 1 V
Figure 6-59. PATHSEL Switching Threshold vs Power Supply
D060
PATHSEL = high, OPS input: VIN+ = 1 V
Figure 6-60. OPS Shutdown Threshold vs Power Supply
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
21
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6.14 Typical Characteristics: Gain Drift
at +VCC = 6 V, –VCC = –6 V, 50-Ω D2S source impedance , VIC = 0.25 V, internal path selected (PATHSEL = GND), VREF =
GND, D2S RLOAD = 100 Ω at pin 6, RF = 249 Ω, RG = 162 Ω, OPS on (DISABLE = GND), OPS RLOAD = 100 Ω at pin 11, and
TJ ≈ 25°C (unless otherwise noted)
2
12
10
6
5
4
4
125
Gain Drift (ppm/qC)
D061
30 units shown
Figure 6-61. D2S Gain Over Temperature
Figure 6-62. D2S Gain Drift Histogram
10
9
9
8
8
5
4
3
2
2
1
125
0
0
Gain Drift (ppm/qC)
D063
30 units shown
Figure 6-63. OPS Gain Over Temperature
Figure 6-64. OPS Gain Drift Histogram
11
10
10
9
6
6
5
4
3
3
2
0
0
0
Gain Drift (ppm/qC)
30 units shown
Figure 6-65. Midscale Buffer Gain Over Temperature
0
0
-1.14
D065
0
-1.17
125
-1.2
105
-1.44
85
-1.5
5
25
45
65
Junction Temperature (0C)
-1.47
0
-15
-1.26
1
-1.29
2
0.9993
-1.32
0.9994
7
-1.35
0.9995
8
-1.38
0.9996
-1.41
Frequency (# of Units)
9
-1.23
0.9997
-35
D064
30 units from –40°C to +125°C
0.9998
0.9992
-55
2
0
15
105
5
85
0
5
25
45
65
Junction Temperature (0C)
-5
-15
-10
0
-35
-15
2.512
-55
2
1
10
2.514
35
2.516
6
6
30
2.518
7
25
2.52
20
Frequency (# of Units)
OPS Gain (V/V)
2.522
Mid-scale Buffer Gain (V/V)
D062
30 units from –40°C to +125°C
2.524
22
42
105
41
85
40
5
25
45
65
Junction Temperature (0C)
0
39
-15
0
34
-35
1
33
0
4
2
2
1.975
-55
7
38
1.98
7
37
1.985
8
36
1.99
35
Frequency (# of Units)
D2S Gain (V/V)
1.995
D066
30 units from –40°C to +125°C
Figure 6-66. Midscale Buffer Gain Drift Histograms
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
7 Parameter Measurement Information
7.1 Overview
The THS3215 comprises three blocks of high-performance amplifiers. Each block requires both frequencyresponse and step-response characterization. The midscale buffer and OPS use standard, single-ended I/O
test methods with network analyzers, pulse generators, and high-speed oscilloscopes. The differential to singleended input stage (D2S) requires a wideband differential source for test purposes. All ac characterization tests
were performed using the THS3215 evaluation module (EVM). The THS3215EVM offers many configuration
options. For most of the D2S-only tests, the OPS was disabled. Figure 7-1 shows a typical configuration for an
ac frequency-response test of the D2S.
The THS3215EVM includes unpopulated, optional, passive elements at the D2S inputs to implement a
differential filter. These elements were not used in the D2S characterization, and the two input pins were
terminated to ground through 49.9 Ω resistors. DC test points are provided through 10 kΩ or 20 kΩ resistors
on all THS3215 nodes. Figure 7-1 also shows the output network used to emulate a 200 Ω load resistance
(RLOAD) while presenting a 50 Ω source back to the D2S output pin. The R3 (= 169 Ω) and R4 (= 73.2 Ω)
resistors combine with the 50 Ω network analyzer input impedance to present a 200 Ω load at VO1 (pin 6),
The impedance presented from the input of the network analyzer back to the D2S output (VO1, pin 6) is 50 Ω.
The 16.5 dB insertion loss intrinsic to this dc-coupled impedance network is removed from the characterization
curves. VREF (pin 14) was connected to GND for all the tests.
VREF
14
TP_IN+
J1
Vin+
R5
10 k
TP_VO1
100
+IN
R1
50
2
R7
10 k
50
x1
From LMH3401
EVM
+
50
R2
R3
169
J3
D2S_OUT
6
50Measurement
System
VO1
250
3
500
x1
73.2
50
R4
±IN
J2
Vin-
10 k
R6
TP_IN-
Figure 7-1. D2S Input and Output Interface Showing 50 Ω Differential Input, and 200 Ω RLOAD at VO1
7.2 Frequency Response Measurement
For D2S and full-signal path (D2S + OPS) characterization, the LMH3401, a very wideband, dc-coupled, singleended to differential amplifier, was used. The LMH3401EVM was used as an interface between a single-ended
source and the differential input required by the D2S, shown in Figure 7-2. The LMH3401 provides an input
impedance of 50 Ω, and converts a single-ended input to a differential output driving through 50 Ω outputs on
each side to what is a 50 Ω termination at each input of the THS3215 D2S.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
23
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Network
Analyzer
GND
Port 1
50
Port 2
50
THS3215EVM
LMH3401EVM
+ _
± +
IN+
IN-
+
±
Figure 7-2. Frequency-Response Measurement: D2S and Full-Path (D2S + OPS) Circuit Configurations
The LMH3401 provides 7 GHz bandwidth with 0.1-dB flatness through 700 MHz. From the single-ended
matched input (using active match through an internal 12.5 Ω resistor), the LMH3401 produces a differential
output with 16-dB gain to the internal output pins. Building out to a 50 Ω source by adding external 40.2 Ω
resistors on both differential outputs in series with the internal 10 Ω resistor, results in a net gain of 10 dB to the
matched 50 Ω load on the THS3215EVM.
The maximum output swing test for the D2S is 4 VPP (see HD2 vs Output Voltage and HD3 vs Output Voltage).
With a fixed gain of 2 V/V, the tests in HD2 vs Output Voltage and HD3 vs Output Voltage require a 2 VPP
differential input. In order to achieve the 2 VPP differential swing at the D2S inputs, the LMH3401 internal outputs
must drive a 4 VPP differential signal around the VOCM of the LMH3401. This LMH3401 single-to-differential
preamplifier is normally operated with ±2.5 V supplies, and VOCM set to ground. Under these conditions, the
LMH3401 supports ±1.4 V on each internal output pin; well beyond the maximum required for THS3215 D2S
characterization of ±1 V.
The output of the LMH3401EVM connects directly to the Vin+ (J1) and Vin– (J2) SMA connectors on the
THS3215EVM, as shown in Figure 7-1. The physical spacing of the SMA connectors lines up for a direct
(no cabling) connection between the two different EVMs using SMA barrels. For THS3215 designs that
must be evaluated before any DAC connection, consider using the LMH3401EVM as a gain of 10 dB,
single-to-differential interface to the inputs of the D2S. This setup allows single-ended sources to generate
differential output signals through the combined LMH3401EVM to THS3215EVM configuration. The D2S,
small-signal, frequency-response curves over input common-mode voltage (see Frequency Response vs Input
Common-Mode Voltage) were generated by adjusting the LMH3401 voltage supplies and maintaining VOCM at
midsupply to preserve input headroom on the LMH3401. In order to make single-ended, frequency-response
measurements, the configuration shown in Figure 7-3 was used.
Network
Analyzer
GND
Port 1
50
Port 2
50
THS3215EVM
+
±
Figure 7-3. Frequency-Response Measurement: OPS Inverting and Noninverting, Midscale Buffer, and
VREF-Input Circuit Configurations
24
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
7.3 Harmonic Distortion Measurement
The distortion plots for all stages used a filtered high-frequency function generator to generate a very lowdistortion input signal. The LMH3401 interface was used when testing the D2S and the full-signal path (D2S
+ OPS) harmonic distortion performance. Running the filtered signal through the LMH3401, as shown in
Figure 7-4, provided adequate input signal purity because of the approximately –100-dBc harmonic distortion
performance through 100 MHz provided by the LMH3401. In order to test the harmonic-distortion performance of
the OPS and midscale buffer, the configuration shown in Figure 7-5 was used.
Function
Generator
-
THS3215EVM
LMH3401EVM
< >
Low-Pass Filter
Output
IN+
+ _
50
± +
IN-
+
±
I Input
Q Input
Spectrum
Analyzer
High-Pass Filter
RF
Input
Ext Trig
20-dB
Attenuator
50
Figure 7-4. Harmonic-Distortion Measurement: D2S and Full-Path (D2S + OPS) Circuit Configurations
Function
Generator
-
THS3215EVM
< >
Low-Pass Filter
Output
+
50
±
I Input
Q Input
Spectrum
Analyzer
RF
Input
Ext Trig
High-Pass Filter
50
20-dB
Attenuator
Figure 7-5. Harmonic-Distortion Measurement: OPS Inverting and Noninverting and Midscale Buffer
Circuit Configurations
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
25
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
7.4 Noise Measurement
All the noise measurements were made using the very low-noise, high-gain bandwidth LMH6629 as a low-noise
preamplifier to boost the output noise from the THS3215 before measurement on a spectrum analyzer, as shown
in Figure 7-6. The 0.69-nV/√ Hz input-voltage noise specification of the LMH6629 provides flat gain of 20 V/V
through 100 MHz with its ultrahigh, 6.3-GHz gain bandwidth product. The D2S and OPS noise was measured
with the common-mode voltage at GND.
I Input
Q Input
Spectrum
Analyzer
RF
Input
Ext Trig
50
THS3215EVM
LMH6629
Noise Preamp
+
+
±
±
Figure 7-6. Noise Measurement Using LMH6629 Preamplifier
7.5 Output Impedance Measurement
Output impedance measurement for the three stages under different conditions were performed as a smallsignal measurement calibrated to the device pins using an impedance analyzer. Calibrating the measurement to
the device pins removes the THS3215EVM parasitic resistance, inductance, and capacitance from the measured
data.
7.6 Step-Response Measurement
Generating a clean, fast, differential-input step for time-domain testing presents a considerable challenge. A
multichannel pulse generator with adjustable rise and fall times was used to generate the differential pulse to
drive D2S inputs in Large-Signal Step Response vs Load Resistance. A high-speed scope was used to digitize
the pulse response.
7.7 Feedthrough Measurement
In order to test the forward-feedthrough performance of the OPS in the disabled state, the circuit shown in Figure
7-7 was used. The PATHSEL pin was driven low to select the internal path between the D2S and OPS. A 100
mVPP, swept-frequency, sinusoidal signal was applied at the VREF pin, and the output signal was measured at
the OPS output pin (VOUT, pin 11). The transfer function from VREF to the output of the D2S at VO1 has a gain
of 0 dB, as shown in VREF Input Pin Frequency Response. The results shown in OPS Forward Feedthrough in
Disable account for the 6 dB loss due to the doubly-terminated OPS output, and report the forward feedthrough
between VOUT and VO1 at different OPS gains. The D2S inputs were grounded through 50 Ω resistors for this
test.
26
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Network
Analyzer
Port 1
50
GND
Port 2
50
75
VREF
16
15
14
13
RG
50 k
12
100
1
x1
18.5 k
RF
50 k
50
49.9
x1
+
2
49.9
11
VOUT
+
250
3
500
DISABLE = High
x1
10
18.5 k
49.9
PATHSEL = Low
4
9
49.9
5
6
7
8
200
Figure 7-7. Forward-Feedthrough Test Circuit
In order to test the reverse feedthrough performance of the OPS in its disabled state, the circuit shown in Figure
7-8 was used. The PATHSEL pin was driven high to select the external path to the OPS noninverting pin, VIN+,
pin 9. A 100 mVPP, swept-frequency, sinusoidal signal was applied at the VIN+ pin and the output signal was
measured at the D2S output pin (VO1, pin 6). The results shown in OPS Reverse Feedthrough in Disable
account for the 16.5 dB loss due to the D2S termination, and the test reports the reverse feedthrough between
the VO1 and VIN+ pins. The D2S inputs were grounded through 50 Ω resistors for this test.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
27
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
16
15
14
13
162 Ÿ
50 k
12
100
1
x1
18.5 k
249 Ÿ
50 k
50
x1
+
2
49.9
11
100
+
250
3
500
DISABLE = High
x1
10
18.5 k
49.9
VIN+
4
Network
Analyzer
9
PATHSEL = High
49.9
5
6
7
GND
8
Port 1
50
Port 2
50
VO1
169
73.2
Figure 7-8. Reverse-Feedthrough Test Circuit
7.8 Midscale Buffer ROUT Versus CLOAD Measurement
For the tests in Series Resistance vs Capacitive Load and Frequency Response vs Capacitive Load, the circuit
shown in Figure 7-9 was used. The 150 Ω load circuit configured as shown, provides a 50 Ω path from the
network analyzer back to the output of the buffer. As shown in Figure 7-9, place ROUT below the load capacitor
to improve the phase margin of the closed-loop buffer output, while adding 0 Ω dc impedance into the line
connecting VMID_OUT (pin 15) to the VREF pin. When using the midscale buffer to drive the VREF input, use a
decoupling capacitor at VMID_OUT to reduce broadband noise and source impedance.
28
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Network
Analyzer
GND
Port 1
50
Port 2
50
+VCC2
16
150Ÿ
Load
50 k
VMID_OUT
VMID_IN
1
49.9
x1
118
15
CLOAD
50 k
88.7
ROUT
5
-VCC2
Figure 7-9. ROUT Versus CLOAD Measurement Circuit
8 Detailed Description
8.1 Overview
The THS3215 is a differential-input to single-ended output amplifier system that provides the necessary
functional blocks to convert a differential output signal from a wideband DAC to a dc-coupled, single-ended,
high-power output signal. The THS3215 typically operates using balanced, split supplies. Signal swings through
the device can be adjusted around ground at several points within the device. Single-supply operation is also
supported for an ac-coupled signal path. The THS3215 supply voltage ranges from ±4.0 V to ±7.9 V. The two
internal logic gates rely on a logic reference voltage at pin 7 that is usually tied to ground for any combination of
power-supply voltages. The DISABLE control (pin 10) turns the output power stage (OPS) off to reduce power
consumption when not in use.
A differential-to-single-ended stage (D2S) provides a high input impedance for a high-speed DAC (plus any
reconstruction filter between the DAC and THS3215) operating over a common-mode input voltage range
from –1 V to +3.0 V. This range is intended to support either current sourcing or current sinking DACs. The
D2S is internally configured to reject the input common-mode voltage and convert the differential inputs to a
single-ended output at a fixed gain of 2 V/V (6 dB).
An uncommitted, on-chip, wideband, unity-gain buffer is provided (between pins 1 and 15) to drive the VREF pin.
The buffer offers extremely broad bandwidth to achieve very-low output impedance to high frequencies (Buffer
Output Impedance vs Load Current). The buffer does not provide a high full-power bandwidth because of a
relatively low slew rate. The buffer stage includes a default midsupply bias resistor string of 50 kΩ each to set
the default input to midsupply. This 25 kΩ Thevinin impedance is easily overridden with an external input source,
but is intended to provide a midsupply bias for single-supply operation. The buffer amplifier that drives the VREF
pin has two functions:
•
•
Provides an easy-to-interface, dc-correction, servo-loop input
Provides an optional offset injection point for the D2S output
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
29
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
The final OPS provides a very high-performance, current-feedback amplifier for line-driving applications. The 700
MHz small-signal bandwidth (SSBW) stage provides 3000 V/μs of slew-rate, sufficient to drive a 5 VPP output
with 270 MHz bandwidth. In addition, the OPS is able to drive a very-high continuous and peak output current
sufficient to drive the most demanding loads at very high speeds. A unique feature added to the OPS is a 2 × 1
input multiplexer at the noninverting input. The PATHSEL control (pin 4) is used to select the appropriate signal
path to the OPS noninverting input. One of the multiplexer select paths passes the internal D2S output directly to
the OPS. The other select path accepts an external input to the OPS at VIN+ (pin 9). This configuration allows
the D2S output, available at VO1 (pin 6), to pass through an external RLC filter and back into the OPS at VIN+
(pin 9).
If the OPS does not require power for certain application configurations, a shutdown feature has been included
to reduce power consumption. For designs that do not use the OPS at all, two internal fixed resistors are
included to define the operating points for the disabled OPS. An approximate 18.5 kΩ resistor to the logic
reference (GND, pin 7) from VIN+ (pin 9), and an approximate 18.5 kΩ, fixed, internal feedback resistor are
included to hold the OPS pin voltages in range if no external resistors are used around the OPS. These resistors
must be included in the design calculations for any external network.
Two sets of power supply-pins have been provided for both the positive and negative supplies. –VCC2 (pin 5)
and +VCC2 (pin 16) power the D2S and midscale buffer stages, while –VCC1 (pin 8) and +VCC1 (pin 13) supply
power to the OPS. The supply rails are connected internally by antiparallel diodes. Externally, connect power first
to the OPS, then connect back on each side with a π-filter (ferrite bead + capacitor) to the input-stage supply
pins (see Figure 8-15). Do not use mismatched supply voltages on either the positive or negative sides because
the supplies are internally connected through the antiparallel diodes. Imbalanced positive and negative supplies
are acceptable, however.
When the OPS is disabled, the output pin goes to high impedance. Do not connect two OPS outputs from
different devices together and select them as a wired-or multiplexer. Although the high-impedance output is
disabled, the inverting node is still available through the feedback resistor, and can load the active signal. The
signal path through the inverting node typically degrades the distortion on the desired active signal in a wired-or
multiplexer configuration using current-feedback amplifiers (CFAs).
8.2 Functional Block Diagram
+VCC2
VMID_OUT
16
15
VREF
+VCC1
14
13
50 k
12 VIN±
100
VMID_IN 1
x1
18.5 k
50 k
50
+IN 2
x1
11 VOUT
+
+
250
±IN
3
500
x1
10 DISABLE
18.5 k
9 VIN+
PATHSEL 4
30
5
6
7
8
±VCC2
VO1
GND
±VCC1
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
8.3 Feature Description
8.3.1 Differential to Single-Ended Stage (D2S) With Fixed Gain of 2 V/V (Pins 2, 3, 6, and 14)
This buffered-amplifier stage isolates the DAC output pins from the differential to single-ended conversion.
Present two high-impedance inputs to allow the DAC to operate in its best configuration independent of
subsequent operations. The two very wideband input buffers hold an approximately constant response shape
over a wide input common-mode operating voltage. Frequency Response vs Input Common-Mode Voltage
shows 6 dB of gain with 0.5 dB flatness through 100 MHz over the intended –1 V to +3 V input common-mode
range. In this case, the VREF pin is grounded, forcing the D2S output to be centered on ground for any input
common-mode voltage. For the D2S-only tests, a 100 Ω load is used to showcase the performance of this
stage directly driving a doubly-terminated cable. The wide, input common-mode range of the D2S satisfies the
required compliance voltage over a wide range of DAC types. Most current sourcing DACs require an average
dc compliance voltage on their outputs near ground. Current sinking DACs require an average dc compliance
voltage near their positive supply voltage for the analog section. The 3 V maximum common-mode range is
intended to support DAC supplies up to 3.3 V, where the average output operating current pulls down from 3.3 V
by the termination impedance from the supply. For instance, a 20 mA tail current DAC must level shift from a 3.3
V bias on the output resistors down to 3 V or lower. This DAC-to-THS3215 configuration requires at least a 300
mV dc level shift with half the tail current in each side, implying a 30 Ω load impedance to the supply on each
output side using a 20 mA reference current.
The overriding limits to the input common-mode operating range are due to the input buffer headroom. Over
temperature, the D2S input headroom specification is 2 V to the negative supply and 1.5 V to the positive supply.
Therefore, operation at a 3 V input common-mode voltage requires at least a 4.5 V positive supply, where 5 V is
a more conservative minimum.
While DAC outputs rarely have any common-mode signal present (unless the reference current is being
modulated), the D2S does a reasonable job of rejecting input common-mode signals over frequency. CommonMode Rejection Ratio vs Input Common-Mode Voltage shows the CMRR to decrease above 10 MHz. For
current-sinking DACs coming from a positive supply voltage, any noise on the positive supply looks like an input
common-mode signal. Keeping the noise low at higher frequencies reduces the possibility of feedthrough to the
D2S output due to the decreasing CMRR at higher frequencies. A current-sinking DAC uses pull-up resistors to
the voltage supply to convert the DAC output current to a voltage. Make sure that the DAC voltage supply is
properly decoupled through a ferrite-bead-and-capacitor, π-filter network, similar to the supply decoupling for the
THS3215 shown in Figure 8-15.
The D2S provides a differential gain of 6 dB. The gain is reasonably precise using internal resistor matching
with extremely low gain drift over temperature (see D2S Gain Over Temperature and D2S Gain Drift Histogram).
The single-ended D2S output signal can be placed over a wide range of dc offset levels using the VREF pin.
The VREF pin shows a precise gain of 1 V/V to the D2S output. Grounding VREF places the first stage output
centered on ground (with some offset voltage). For best ac performance through the D2S, anything driving the
VREF pin must have a very wide bandwidth with very low output impedance over frequency while driving a 150
Ω load. The on-chip midscale buffer provides these features (see Buffer Output Impedance vs Load Current).
When a dc offset (or other small-level ac signal) must be applied to the VREF pin, buffer the signal through the
midscale buffer stage. Maintain the total range of the dc offset plus signal swing within the available output swing
range of the D2S. The headroom to the supplies is a symmetric ±2.1 V (maximum) over temperature. Therefore,
on the minimum ±4 V supply, the D2S operates over a ±1.9 V output range. At the maximum ±7.9 V supply, a
±5.8 V output range is supported. At the higher swings, account for available linear output current, including the
current into the internal feedback resistor load of approximately 500-Ω.
Figure 8-1 shows the internal structure of the D2S functional block. It consists of two internal stages:
1. The first stage consists of two wideband, closed-loop, fixed gain of 1 V/V buffers to isolate the requirements
of the complementary DAC output from the difference operation of the D2S.
2. The second stage is a wideband CFA configured as a difference amplifier, operating in a fixed gain of 2 V/V,
performing the differential to single-ended conversion.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
31
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Complementary
Output DAC
10 mA
3
RF
500
RG
250
INx1
VO1 = 2VIN
25
VIN
IDIFF
+
R1
50
2
IN+
10 mA
25
6
VO1
x1
R2
100
14 VREF
Optional DC
Source
Figure 8-1. D2S Operating Example
The CFA design offers the best, full-power bandwidth versus supply current, with moderate noise and dc
precision. Figure 8-1 shows a typical current-sourcing DAC with a 20 mA total tail current. The tail current is
split equally between the 25 Ω termination resistors to produce a dc common-mode voltage and a differential ac
current signal. This example sets the input common-mode voltage at 0.25 V, and is also the compliance voltage
of the DAC. The 25 Ω termination resistors shown here are typically realized as a 50 Ω matched reconstruction
(or Nyquist) filter between the DAC and the THS3215 buffer inputs for most AWG applications. The DAC signal
is further amplified by 6 dB in the second stage for a net transimpedance gain of 100 Ω to the D2S output
at VO1. This configuration produces a 2 VPP output for the 20 mA reference current assumed in the example
of Figure 8-1. The input common-mode voltage is cancelled on the two sides of the op amp circuit to give a
ground referenced output. Any voltage applied to VREF (pin 14) has a gain transfer function of 1 V/V to VO1,
independent of the signal path, as long as the source impedance of VREF is very low at dc and over frequency.
The IN+ buffer output drives a 150 Ω load with VREF grounded. Any source driving VREF must have the ability
to drive a 150 Ω load with low output impedance across frequency. For differential input signals, the IN– buffer
drives a 150 Ω active load. The active load is realized by a combination of the 250 Ω RG resistor and the inverted
and attenuated signal present at the inverting terminal of the difference amplifier stage. If only IN– is driven (with
IN+ at a dc fixed level), the load is 250 Ω.
The resistor values around the D2S difference amplifier are derived in the following sequence, as shown in
Figure 8-2:
1. Select the feedback resistor value to set the response shape for the wideband CFA stage. The 500 Ω design
used here was chosen as a compromise between loading and noise.
2. Set the input resistor on the inverting input side to give the desired single-sided gain for that path. Setting
RG= 250 Ω results in a gain of –2 V/V from the buffered signal (–V) to the output of the difference amplifier.
3. Solve the required attenuation to the noninverting input to get a matched gain magnitude for the signal
provided at the buffer output (+V) on the noninverting path. If α = R2 / (R1 + R2), as shown in Figure 8-2,
then the solution for α is shown in Equation 2:
§
RF ·
D ¨1
¸
© RG ¹
D
32
2
3
2
(1)
R1
R1 R2
(2)
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
RG
250
RF
500
±V
.(+V)
+
VO1
R1
+V
R2
Figure 8-2. D2S Impedance Analysis
4. After solving the attenuation from the buffer output to the amplifier noninverting input, set the impedance
(R1 + R2). It is preferable to have the two first-stage buffer outputs drive the same load impedance to match
nonlinearity in their outputs in order to improve even-order harmonic distortion. The load impedance from –V
to RG has an active impedance because of the inverted and attenuated version of the input signal appearing
at the inverting amplifier node from the +V input signal. Assuming a positive input signal into the +V path,
an attenuated version of the signal appears at the amplifier summing junction side of RG, while the inverted
version of the signal appears on the input side of RG.
The impedance seen at node –V in Figure 8-2 is derived in Equation 3 by solving for the V/I expression across
RG.
Zi
RG
1 D
250
1
2
3
150
(3)
For load balancing, (R1 + R2) = 150 Ω while the attenuation is α. More generally, all the terms are now available
to solve for R2, as shown in Equation 4:
R2
RG
D
D 1
2
3
250
1
2
3
(4)
R1 is then simply (Zi – R2) = 50 Ω.
This analysis for matched gains and buffer loads can be applied to a more general, discrete design using
different target gains and starting RF values. It is clearly useful to have the attenuation and buffer loading
accurately controlled. Therefore, it is very important to control the impedance at VREF (pin 14) to be as low
as possible. For instance, using the midscale buffer to drive VREF only adds 0.21 Ω dc impedance in series
with R2. This low, dc output impedance can only be delivered with a closed-loop buffer design. For discrete
implementations of this D2S, consider the BUF602 buffer and LMH6702 wideband CFA. For even better dc and
ac output impedance in the buffers (and possibly better gain), use a closed-loop, dual, wideband op amp like
the OPA2889 for lower frequency applications, or the OPA2822 for higher frequency. These unity gain stable
op amps can be used as buffers, offering different performance options along with the LMH6702 wideband CFA
over the design point chosen for the THS3215.
After gain matching is achieved in the single op amp differential stage, the common-mode input voltage is
cancelled to the output, and the VREF input voltage is amplified by 1 V/V to the output. The analysis circuit is
shown in Figure 8-3, where VREF is shown grounded at the R2 element.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
33
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
RG
250
RF
500
VCM
+
VO1
R1
50
R2
100
Figure 8-3. D2S Common-Mode Cancellation
The gain magnitudes are equal on each side of the differential inputs; therefore, the common-mode inputs
achieve the same gain magnitude, but opposite phase, resulting in common-mode signal cancellation. The
inverting path gain is VCM × (RF / RG). The noninverting path gain is VCM × α × (1 + RF / RG). Using Equation 5:
D
RF
RG
§
RF ·
¨1
¸
© RG ¹
(5)
the noninverting path gain becomes +VCM × RF / RG, and adding that result to the inverting path signal cancels
the input common-mode voltage to zero. Slight gain mismatches reduce this rejection to the 48 dB typical
CMRR, with a 42 dB tested minimum. The 42 dB minimum over the 3 V maximum common-mode input range
adds another ±23.8 mV worst-case D2S output offset term to the specified maximum ±35 mV output offset with 0
V input common-mode voltage. The polarity of the gain mismatch is random.
The VREF pin input voltage (VREF) generates a gain of 1 V/V using the analysis shown in Figure 8-4.
RG
250
RF
500
+
VO1
R1
50
R2
100
VREF
Figure 8-4. Gain Transfer Function from VREF to VO1
The gain from VREF to VO1 is shown in Equation 6:
VREF
§
RF ·
R1
¨1
¸
R1 R2 © RG ¹
VO1
(6)
Getting both R1 and (R1 + R2) in terms of RG and the target attenuation, α simplifies, as shown in Equation 7:
R1
R1 R2
34
1 D
1 D
1
RG
1 D
RG
1 D
(7)
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Putting Equation 7 back into the gain expression (Equation 6), and expanding out gives:
§
RF ·
VREF 1 D ¨ 1
¸
© RG ¹
VO1
(8)
Substituting the value of α from Equation 5 into Equation 8 reduces the expression to VO1 = VREF, a gain of
1 V/V. This gain is very precise, as shown in the D2S Electrical Characteristics table, where the tested dc limits
are 0.975 V/V to 1.015 V/V.
The D2S output offset and drift are largely determined by the internal elements. The only external consideration
is the dc source impedance at the two buffer inputs. With low source impedance, the D2S output offset is tested
to be within ±35 mV, that becomes a maximum ±17 mV input differential offset specification. Assuming the dc
source impedances are closely matched, the mismatch in the two input bias currents adds another input offset
term for higher source impedances. The input bias offset current is limited in test to be < ±0.40 µA. This error
term does not rise to add more than ±1 mV input differential offset until the dc source impedance exceeds
2.5 kΩ. A high dc source impedance most commonly occurs in an input ac-coupled, single-supply application,
where dc offsets are less critical.
The absolute input bias currents modify the common-mode input voltage if the dc source resistance is too large.
The input bias current is tested to a limit of ±4 µA on each input. In order to move the input common-mode
voltage by ±100 mV, the dc source impedance must exceed 25 kΩ. This added input common-mode voltage is
cancelled by the D2S at the output (pin 6) and is set to the reference voltage applied at VREF (pin 14).
The D2S output noise is largely fixed by the internal elements. The D2S shows a differential input voltage noise
of 6 nV/√ Hz, and a current noise of 2 pA/√ Hz on each input. Higher termination resistors increase this source
noise, as given by Equation 9, where Rt is the dc termination impedance at each buffer input. The D2S has a 1/f
corner at approximately 10 kHz (see Differential Input Noise vs Source Impedance).
ei _ diff
6 nV
2
2 4kTR t
2 2 pA u R t
2
(9)
The total differential input noise is dominated by the differential voltage noise. For instance, evaluating this
expression for Rt = 200 Ω on each input, increases the total differential input noise to 6.5 nV/√ Hz, only slightly
greater than the 6 nV/√ Hz for the D2S with 0 Ω source Rt on each input. If higher final output SNR is desired,
consider generating as much input swing as the DAC can support by increasing the termination impedance. It is
possible that a lower tail current with higher Rt can yield improved SNR at the D2S input. This differential input
noise appears at the D2S output times a gain of 2 V/V.
eout _ diff
2 u ei _ diff
(10)
8.3.2 Midscale (DC) Reference Buffer (Pin 1 and Pin 15)
This optional block can be completely unconnected and not used if the design does not require this feature.
Internal 50 kΩ resistors to the power supplies bias the input of the buffer to the midpoint of the supplies used.
The internal resistors set a midsupply operating point when the buffer is not used, as well as a default midsupply
point at the buffer output to be used in other stages for single-supply, ac-coupled applications.
The buffer provides a very wideband, low output-impedance when used to drive VREF, pin 14 (see Buffer Output
Impedance vs Load Current). To provide this low broadband impedance, the closed-loop midscale (dc) reference
buffer offers a very broadband SSBW, but only a modest large-signal bandwidth (LSBW); see Frequency
Response vs Output Voltage. This path is not normally intended to inject a wideband signal, but can be used for
lower-amplitude signals. Driving the buffer output into the VREF pin allows a wideband small-signal term to be
added into the D2S along with the signal from the differential inputs.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
35
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
The midscale (or dc) reference buffer injects an offset voltage to the output offset of the D2S when it drives the
VREF pin. The offset has very low drift, but consider the effect of the input bias current times the dc source
impedance at VMID_IN (pin 1). When used as a default midsupply reference for single-supply operation, the
input to this buffer is just the average of the total power supplies though a 25 kΩ source impedance. Add an
external capacitor to filter the supply and the 50 kΩ internal resistors. A 1-µF capacitor on VMID_IN adds a 6-Hz
pole to the noise sources. If lower noise at lower frequencies is required, implement a midscale divider with
external, lower-valued resistors in parallel with the internal 50 kΩ values.
If the midscale buffer drives the VREF pin, the buffer noise is added to Equation 9 and Equation 10. The
midscale buffer 4.4 nV/√ Hz voltage noise is amplified by 0 dB, and adds (RMS) a negligible impact to the total
D2S output noise. The biggest impact comes when the internal default 50 kΩ dividers are used. Be sure to
decouple VMID_IN with at least a 1 µF capacitor in the application to reduce the noise contribution through this
path. Figure 8-5 shows the simulation circuit with the 1 µF capacitor installed. Figure 8-6 shows the simulated
output noise for the midscale buffer using the internal 50 kΩ divider with and without the 1 µF capacitor on
VMID_IN.
+VCC2
16
50 k
VMID_IN
1
1 …F
15 VMID_OUT
x1
50 k
5
-VCC2
Figure 8-5. Midscale Buffer Noise Model
1000
Input Referred Noise (nV/—Hz)
With 1PF capacitor
Without 1PF capacitor
100
10
1
10
100
1k
10k
Frequency (Hz)
100k
1M
D501
Figure 8-6. Buffer-Output Noise Comparison With and Without the 1 µF Bypass Capacitor on VMID_IN
In the flat region, the 1 µF capacitor reduces the midscale buffer output spot noise from approximately 55 nV/√
Hz to 4.4 nV/√ Hz. If the noise below 100 Hz is unacceptable, either add a low-noise buffer to drive this input,
or add lower-value resistors externally to set up the midsupply bias. Also, consider the noise impact of any
reference voltage source driving the midscale buffer path.
36
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
8.3.3 Output Power Stage (OPS) (Pins 4, 7, 9, 10, 11, and 12)
A wideband CFA provides a flexible output driver with several unique features. The OPS can be left unused if
the specific application only uses the D2S alone, or a combination of the D2S with an off-chip power driver. If
left unused, simply tie DISABLE (pin 10) and PATHSEL (pin 4) to the positive supply. This logic configuration
turns the OPS off and opens up the external and internal OPS noninverting input paths. An internal fixed 18.5 kΩ
resistor holds the external input pin at the logic reference voltage on GND (pin 7). Additionally, the OPS output is
connected to the inverting input through another internal 18.5 kΩ resistor when no external resistors are installed
on VIN+, VOUT, or VIN– (pins 9, 11, or 12, repectively). Disabling the OPS saves approximately 11 mA of supply
current from the nominal total 35 mA, with all stages operating on ±6 V supplies.
The noninverting input to the OPS provides two possible paths controlled by the PATHSEL logic control. With
the logic reference (pin 7) at ground, floating PATHSEL or controlling it to a voltage < 0.7 V connects the input
path directly to the internal D2S output. Tying PATHSEL to the positive supply, or controlling it to a logic level
> 1.3 V, connects the input path to the external input at VIN+. The intent for this switched input is to allow an
external filter to be inserted between the D2S output and OPS inputs when needed, and bypass the filter when
not. Alternatively, this switched input also allows a completely different signal path to be inserted at the OPS
input, independent of that available at the internal D2S output.
In situations where the D2S output at VO1 (pin 6) is switched into another off-chip power driver, the OPS can
be disabled using DISABLE. With the logic reference (pin 7) at ground, floating DISABLE, or controlling it to a
voltage < 0.7 V, enables the OPS. Tying DISABLE to the positive supply, or controlling it to a logic level > 1.3 V,
disables the OPS.
Operation of the wideband, current-feedback OPS requires an external feedback resistor and a gain element.
After configuring, the OPS can amplify the D2S output through either the noninverting path, or be configured as
an inverting amplifier stage using the external OPS input at VIN+ as a dc reference.
One of the first considerations when designing with the OPS is determining the external resistor values as a
function of gain in order to hold the best ac performance. The loop gain (LG) of a CFA is set by the internal openloop transimpedance gain from the inverting error current to the output, and the effective feedback impedance to
the inverting input. The nominal internal open-loop transimpedance gain (ZOL) magnitude and phase are shown
in Figure 8-7.
140
45
120
0
100
-45
80
-90
60
-135
40
1k
10k
100k
1M
10M
Frequency (Hz)
100M
Open-Loop Phase (q)
Open-Loop Magnitude (dB:)
Phase
Magnitude
-180
2G
D502
Figure 8-7. Simulated OPS ZOL Gain Magnitude and Phase
The feedback transimpedance (ZOPT) can be approximated as shown in Equation 11, where Ri is the open-loop,
high-frequency impedance into the inverting node of the OPS. For a detailed derivation of Equation 11, see the
Setting Resistor Values to Optimize Bandwidth section in the OPA695 datasheet (SBOS293).
ZOPT | RF
§
RF ·
¨1
¸ Ri
© RG ¹
(11)
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
37
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
As the signal gain is varied, hold ZOPT approximately constant to hold the ac response constant over gain.
Holding ZOPT constant is a requirement to solve for RF. An example of the THS3215 OPS RF derivation is shown
in Equation 12:
RF
430
§
¨
©
RF ·
¸u
RG ¹
(12)
The calculations are complicated by the internal feedback resistor value of approximately 18.5 kΩ. After the
external RF is approximately set by the constant bandwidth consideration, the RG must be set considering the
other gain error terms. From the noninverting input of a CFA, the total gain to the output includes a loss through
the input buffer stage (described by the CMRR) and the loop gain (LG) loss set by the typical dc open-loop
transimpedance gain and the feedback transimpedance. Extract the buffer gain from the VIN+ input to the VIN–
input from the CMRR using Equation 13. This gain loss only applies to the noninverting mode of operation and
can be ignored in inverting mode operation.
E
§
¨ 1 10
¨
©
CMRR
20
·
¸
¸
¹
Buffer Gain CFA
(13)
The OPS has a typical CMRR of 53 dB (buffer gain, β = 0.9978) with a tested minimum of 47 dB (minimum
buffer gain of 0.9955). The dc LG adds to the gain error. The LG is given by Equation 14, where the typical
design gain of 2.5 V/V value is also shown (the 245 Ω shown for RF is the external 249 Ω feedback resistor in
parallel with the internal 18.5 kΩ feedback resistor).
LG
RF
ZOL
NG u Ri
1.7 M
245
3593
u
(14)
The closed-loop output impedance with a heavy load also adds a minor gain loss that is neglected here. The
total noninverting gain is then set by Equation 15 (remember to include the internal RF in this analysis). The RF’
shown here is the parallel combination of the internal and external feedback resistors.
Av
§
RF ·
LG
E u ¨1
¸u
R
1
LG
G ¹
©
(15)
Using nominal values for each term at the specified RF = 249 Ω and RG = 162 Ω gives the gain calculation in
Equation 16, yielding a nominal gain very close to 2.5 V/V.
Av
245.7 ·
3593
§
0.9978 u ¨ 1
¸ u 1 3593
162
©
¹
2.51
(16)
Testing the total gain spread with the internal variation in buffer gain, open-loop transimpedance gain, internal
feedback resistor, and ±1% external resistor variation gives a worst-case gain spread of 2.5 V/V to 2.52 V/V. The
gain error is primarily dominated by the external 1% resistors. For the tighter tolerance shown in Table 8-1, use
0.1% precision resistors.
At very low gains (< 1.5 V/V), parasitic effects at the inverting input due to stray inductance and capacitance
render a flat frequency response impossible. Looking then at gains from 1.5 V/V and up, a table of nominally
recommended RF and RG values is shown in Table 8-1. Do not operate the OPS in noninverting gains of less
than 2.5 V/V for large output signals because the limited slew-rate of the CFA input buffer causes signal
degradation. Table 8-1 accounts for the nominal gain losses described previously, and uses standardized
resistor values to minimize the nominal gain-error to target gain. The calculation also restricts the solution to
a minimum RG = 20 Ω. The gain calculations include the nominal buffer gain loss, the loop-gain effect, and the
nominal internal feedback resistor = 18.5 kΩ.
38
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Table 8-1. Optimized RF Values for Different OPS Noninverting Signal Gains
CALCULATED GAIN
TARGET GAIN
(V/V)
MEASURED SSBW
(MHz)
BEST RF
(Ω)
BEST RG
(Ω)
(V/V)
(dB)
GAIN ERROR
(%)
1.5
890
324
634
1.498
3.513
-0.1
2
—
287
280
2.004
6.039
0.22
2.5
700
249
162
2.510
7.995
0.41
3
—
205
102
2.980
9.485
-0.66
3.5
—
169
66.5
3.510
10.905
0.27
4
—
150
49.9
3.972
11.980
-0.7
4.5
—
158
44.2
4.533
13.128
0.73
5
390
158
39.2
4.984
13.952
-0.32
5.5
—
165
36.5
5.467
14.755
-0.6
6
—
169
33.2
6.029
15.605
0.49
6.5
—
169
30.1
6.547
16.321
0.73
7
—
174
28.7
6.989
16.888
-0.16
7.5
—
174
26.7
7.437
17.429
-0.83
8
—
178
24.9
8.060
18.127
0.75
8.5
—
178
23.2
8.578
18.668
0.92
9
—
178
22.1
8.955
19.041
-0.5
9.5
—
182
21
9.558
19.608
0.61
10
93
187
20.5
10.006
20.005
0.06
The measured bandwidths in Table 8-1 come from Frequency Response vs Noninverting Gain using the resistor
values in the table and a 100 Ω load. Plotting the RF value versus gain gives the curve of Figure 8-8. The curve
shows some ripple due to the standard value resistors used to minimize the target dc gain error.
350
300
RF Value (:)
250
200
150
100
50
0
1
2
3
4
5
6
7
Target OPS Gain (V/V)
8
9
10
D503
Figure 8-8. Suggested External RF Value vs Noninverting Gain for the OPS
Using RF values greater than the recommended values in Table 8-1 band-limits the response, whereas using
less than the recommended RF values peaks the response. Using the values shown in Table 8-1 results in a
more constant SSBW (see Frequency Response vs Noninverting Gain. Holding a more constant loop-gain over
the external gain setting also acts to hold a more constant output impedance profile, as shown in Figure 8-9.
The swept-frequency, closed-loop, output impedance is shown for gains of 2.5 V/V, 5 V/V, and 10 V/V using the
RF and RG values of Table 8-1. The first two steps do a good job of delivering the same (and very low) output
impedance over frequency, while the gain of 10 V/V shows the expected higher closed-loop output impedance
due to the reduced loop-gain and bandwidth.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
39
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Output Impedance (:)
10
1
0.1
AV = 2.5 V/V
AV = 5 V/V
AV = 10 V/V
0.01
100k
1M
10M
Frequency (Hz)
100M
D504
Figure 8-9. OPS Closed-Loop Output Impedance vs Gain Setting
Reducing the RF value with increasing gain also helps minimize output noise versus a fixed RF design. See
Input-Referred Spot Noise vs Frequency for the three noise terms for the OPS. The total output noise calculation
is shown in Equation 17:
eo
eni2
4kTRS
ibnRS
2
NG2
ibiRF
2
4kTRF NG
(17)
where
•
•
•
RS is the source impedance on the noninverting input. If the OPS is driven from the D2S directly using the
internal path, RS ≈ 0 Ω.
NG = (1 + RF / RG) for the design point.
The flat-band noise numbers for the OPS are:
– Eni = 2.7 nV/√ Hz
– Ibn = 1.3 pA/√ Hz
– Ibi = 18 pA/√ Hz
Using the values of RF and RG listed in Table 8-1, a swept gain output- and input-referred noise estimate is
computed, as shown in Table 8-2. In this sweep, RS = 0 Ω. The input-referred noise (Eni) in Table 8-1 is at
the noninverting input of the OPS. To refer the noise to the D2S differential inputs, divide the output noise by
two if there is no interstage loss. Dividing the Eni column by 2 V/V shows that the OPS noise contribution is
negligible when referred to the D2S inputs, where the 6 nV/√ Hz differential input noise dominates. Operating
with higher feedback resistors in the OPS quickly increases the output noise due to the inverting input current
noise term. Although increasing RF improves phase margin (for example, when driving a capacitive load), be
careful to check the total output noise using Equation 17.
Table 8-2. Total Input- and Output-Referred Noise of the OPS Versus Gain
40
TARGET GAIN
(V/V)
BEST RF
(Ω)
BEST RG
(Ω)
EO
(nV/√ Hz)
Ein
(nV/√ Hz)
1.5
324
634
7.63
5.09
2
287
280
8.07
4.03
2.5
249
162
8.72
3.47
3
205
102
9.39
3.15
3.5
169
66.5
10.42
2.97
4
150
49.9
11.48
2.89
4.5
158
44.2
13.01
2.87
5
158
39.2
14.21
2.85
5.5
165
36.5
15.53
2.84
6
169
33.2
17.04
2.83
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Table 8-2. Total Input- and Output-Referred Noise of the OPS Versus Gain (continued)
TARGET GAIN
(V/V)
BEST RF
(Ω)
BEST RG
(Ω)
EO
(nV/√ Hz)
Ein
(nV/√ Hz)
6.5
169
30.1
18.42
2.81
7
174
28.7
19.63
2.81
7.5
174
26.7
20.83
2.8
8
178
24.9
22.51
2.79
8.5
178
23.2
23.89
2.79
9
178
22.1
29.41
2.78
9.5
182
21
26.54
2.78
10
187
20.5
27.77
2.78
Operating the OPS as an inverting amplifier is also possible. When driving the OPS directly from the D2S to the
RG resistor, use the values shown in Table 8-1 for the noninverting mode in order to achieve optimal results.
Note that the RG resistor is the load for the D2S. Operating with the D2S driving an RG < 80 Ω increases the
harmonic distortion of the D2S. In that case, scaling up RF and RG in order to reduce the loading results in better
system performance at the cost of a lower OPS bandwidth. In order to reduce layout parasitics, consider splitting
the RG resistor in two, with the first half close to VO1 and the second half close to VIN– (pin 12). Splitting RG in
this manner places the trace capacitance inside the two resistors, thus keeping both active nodes more stable.
Using the OPS to receive and amplify a signal in the inverting mode with a matched terminating impedance
requires another resistor to ground (RM) along with RG. This RM resistor is shown in Figure 8-10 for a 50 Ω
matched input impedance design.
VIN12
RG
50-Ÿ
Source
RF
RM
OPS
Stage
6
VIN+
11 VOUT
+
From D2S
9
Figure 8-10. Inverting OPS Operation With Matched Input Impedance
Table 8-3 gives the recommended external resistor values versus gain for the inverting gain mode with input
matching configuration. Table 8-3 solves for the required RF to simultaneously allow the gain, input impedance
(50 Ω), and feedback transimpedance to be set to the optimal target values. The table includes the effect of the
internal 18.5 kΩ feedback resistor, and minimizes the RMS error to input impedance target (ZI) and overall gain.
Table 8-3. Resistor Values Versus Gain for the Inverting OPS Configuration
TARGET
GAIN
—(V/V)
MEASURED
SSBW
(MHz)
BEST
RF (Ω)
BEST
RG (Ω)
BEST
RM (Ω)
CALCULATED GAIN
—(V/V)
(dB)
GAIN ERROR
(%)
ZI (Ω)
ZI ERROR
(%)
1
700
294
287
60.4
1.008
0.072
0.835
49.90
-0.003
1.5
—
267
174
69.8
1.533
3.712
2.213
49.82
-0.168
2
—
237
118
86.6
2.009
6.061
0.469
49.95
0.091
2.5
700
226
88.7
113
2.543
8.106
1.705
49.69
-0.415
3
—
215
71.5
169
3.017
9.592
0.577
50.24
0.688
3.5
—
210
59
316
3.553
11.011
1.508
49.72
-0.366
4
—
205
51.1
1910
4.006
12.055
0.161
49.77
-0.264
4.5
—
226
49.9
Open
4.529
13.120
0.645
49.90
–0.200
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
41
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
Table 8-3. Resistor Values Versus Gain for the Inverting OPS Configuration (continued)
TARGET
GAIN
—(V/V)
MEASURED
SSBW
(MHz)
BEST
RF (Ω)
BEST
RG (Ω)
BEST
RM (Ω)
CALCULATED GAIN
—(V/V)
(dB)
GAIN ERROR
(%)
ZI (Ω)
ZI ERROR
(%)
5
570
249
49.9
Open
4.990
13.962
-0.201
49.90
–0.200
5.5
—
274
49.9
Open
5.491
14.793
-0.164
49.90
–0.200
6
—
301
49.9
Open
6.032
15.609
0424
49.90
–0.200
6.5
—
324
49.9
Open
6.493
16.249
-0.108
49.90
–0.200
7
—
348
49.9
Open
6.974
16.870
-0.372
49.90
–0.200
7.5
—
374
49.9
Open
7.495
17.495
-0.067
49.90
–0.200
8
—
402
49.9
Open
8.056
18.122
0.701
49.90
–0.200
8.5
—
422
49.9
Open
8.457
18.544
-0.507
49.90
–0.200
9
—
449
49.9
Open
8.998
19.083
-0.023
49.90
–0.200
9.5
—
475
49.9
Open
9.519
19.572
0.200
49.90
–0.200
10
175
499
49.9
Open
10.000
20.000
0.000
49.90
–0.200
At higher gains, RM increases to larger values, and the resistor is excluded from the circuit. The resulting input
impedance of the network is resistor RG. From that point, RF simply increases to get higher gains, thereby
rapidly reducing the SSBW. However, below a gain of –5 V/V, the inverting design with the values shown in Table
8-3 holds a more constant SSBW versus the noninverting mode (see Frequency Response vs Inverting Gain).
8.3.3.1 Output DC Offset and Drift for the OPS
The OPS provides modest dc precision with typical, minimum, and maximum dc error terms in Table 8-4. The
input offset voltage applies to either input path with very little difference between the internal and external paths.
Table 8-4. Typical Offset and Bias Current Values for the OPS
PARAMETER
TYPICAL
MINIMUM
MAXIMUM
UNIT
VIO
±1
–15
15
mV
Ibn
5
–5
15
µA
Ibi
±5
–75
75
µA
Selecting the internal path results in no source resistance for Ibn, so that term drops out. When the external path
is selected, a dc source impedance may be present, so the Ibn term creates another error term, and adds to the
total output offset.
Stepping through an example design for the OPS output dc offset using the external path with a low insertion
loss filter shown in Figure 8-17, along with its RF and RG values, gives the following results:
•
•
•
RS for the Ibn term = 90.9 Ω || 464 Ω = 76 Ω. (dc source impedance for the filter design)
RF including the internal 18.5 kΩ resistor = 205 Ω || 18.5 kΩ = 202.7 Ω
Resulting gain with the 102 Ω RG element = 2.99 V/V
Table 8-5 shows the typical and worst-case output error terms. Note that a positive current out of the
noninverting input gives a positive output offset term, whereas a positive current out of the inverting input gives a
negative output term.
Table 8-5. Output Offset Voltage Contribution From Various Error Terms at 25°C
42
ERROR TERM
TYPICAL
MINIMUM
MAXIMUM
UNIT
Ibn × RS × AV
1.136
–1.136
3.408
mV
VIO × AV
±2.99
–44.85
44.85
mV
Ibi × RF
±1.014
–15.203
15.203
mV
Total error
–2.87 to +5.14
–61.19
63.46
mV
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
The input offset voltage dominates the error terms. The worst-case numbers are calculated by adding the
individual errors algebraically, but is rarely seen in practice. None of the OPS input dc error terms are correlated.
To compute output drift numbers, use the same gains shown in Table 8-5 with the specified drift numbers.
3
0.12
2
0.08
1
0.04
0
0
-1
-2
-0.04
OPS Output Voltage (V)
PATHSEL In (V)
The OPS PATHSEL control responds extremely quickly with low-switching glitches, as shown in Figure 8-11. For
this test, the D2S input is set to GND, and the output of the D2S is connected to the external OPS input. The
PATHSEL switch is then toggled at 10 MHz. The results show the offset between the internal and external paths
as well matched.
-0.08
PATHSEL In
OPS VOUT
-3
-0.12
Time (20 ns/div)
D505
Figure 8-11. OPS Path-Select Switching Glitch
The OPS includes a disable feature that reduces power consumption from approximately 11 mA to 2 mA. The
logic controls are intended to be ground-referenced regardless of the power supplies used. The logic reference
(GND, pin 7) is normally grounded and also provides a connection to the internal 18.5 kΩ resistor on VIN+ (pin
9, default bias to pin 7). Operating in a single-supply configuration with –VCC at GND and the external OPS
input (VIN+) floated, places VIN+ internally at –VCC = GND. Driving the external OPS input (VIN+) from a source
within the operating range overrides the bias to –VCC. However, if the application requires VIN+ to be floated in
a single-supply operation, consider centering the voltage on VIN+ with an added 18.5 kΩ external resistor to the
+VCC supply.
If the disable feature is not needed, simply float or ground DISABLE (pin 10) to hold the OPS in the enabled
state. Increasing the voltage on the DISABLE pin to greater than 1.3 V disables the OPS and reduces the
current to approximately 2 mA. In a single-supply design, the OPS can be disabled by setting DISABLE to +VCC,
even up to the maximum operating supply of 15.8 V.
Do not move the logic threshold away from those set by the logic ground at pin 7. If a different logic swing level
is required, and GND (pin 7) is biased to a different voltage, be sure the source can sink the typical 280 µA
coming out of GND. Also recognize that the 18.5 kΩ bias resistor on the external OPS input (VIN+) is connected
to GND voltage internally.
As shown in OPS Enable and Disable Time, the OPS enables in approximately 100 ns from the logic threshold
at 1.0 V, while disabling to a final value in approximately 500 ns.
8.3.3.2 OPS Harmonic Distortion (HD) Performance
The OPS in the THS3215 provides one of the best HD solutions available through high power levels and
frequencies. HD2 vs Output Voltage and HD3 vs Output Voltage show the swept-frequency HD2 and HD3,
where the second harmonic is clearly the dominant term over the third harmonic. Typical wideband CFA
distortion is reported only through 2 VPP output, while HD2 vs Output Voltage and HD3 vs Output Voltage
provide sweeps at 5 VPP and 8 VPP into a 100 Ω load. These curves show an approximate 20 dB per decade rise
with frequency due to loop-gain roll-off.
The distortion performance is extremely robust as a function of load resistance (see HD2 vs Load Resistance
and HD3 vs Load Resistance). Normally, heavier loads degrade the distortion performance, as shown by the
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
43
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
HD2 in HD2 vs Load Resistance. However at frequencies greater than 30 MHz, the HD2 actually improves
slightly as the output load is increased from 500 Ω to 100 Ω.
One of the key advantages offered by the CFA design in the OPS is that the distortion performance holds
approximately constant over gain, as seen in the full-path distortion measurements of HD2 vs Gain and HD3 vs
Gain. Here, the D2S provides a fixed gain of 2 V/V driving a 200 Ω interstage load and using the internal path
to drive the OPS at gains from 1.5 V/V to 10 V/V. Hold the loop-gain approximately constant by adjusting the
feedback RF value with gain to achieve vastly improved performance versus a voltage-feedback-based design.
Testing a 5 VPP output from the OPS with the supplies swept from the minimum ±4 V to ±7.5 V in HD2 vs Supply
Voltage and HD3 vs Supply Voltage show:
1. The 1.5 V headroom on ±4 V supplies and ±2.5 V output voltage results in degraded performance. At the
lower supplies, target lower output swings for improved linearity performance.
2. The HD2 does not change significantly with supply voltages above ±6 V. The HD3 does improve slightly at
higher supply-voltage settings.
From these plots at ±7.5 V supplies, a 5 VPP output into 100 Ω load shows better than –60 dBc HD2 and
HD3 performance through 30 MHz. This exceptional performance is available with the OPS configured as a
standalone amplifier. Combining the standalone OPS performance with the D2S (see HD2 vs Frequency and
HD3 vs Frequency) does not degrade the full, signal-path distortion levels. With the D2S and OPS running
together at a final 5 VPP output and 30 MHz, the HD2 changes to –63 dBc and HD3 changes to –59 dBc on ±6
V supplies. Lower output swings for the combined stages provide much lower distortion. The 2 VPP output curves
on HD2 vs Frequency and HD3 vs Frequency show –61 dBc for HD2 and HD3 at 50 MHz.
8.3.3.3 Switch Feedthrough to the OPS
-20
-20
-30
-30
-40
-40
Feedthrough (dBc)
Feedthrough (dBc)
The THS3215 uses two logic control pins that enable one of four combinations of states; therefore, various
feedthrough effects must be considered. OPS Forward Feedthrough in Disable and OPS Reverse Feedthrough
in Disable show the feedthrough of the switches with the OPS disabled. With the OPS enabled, the signal
feedthrough from the deselected input to the OPS output is shown in Forward Feedthrough With OPS Enabled,
Internal Path Selected and Forward Feedthrough With OPS Enabled, External Path Selected at different closedloop OPS gains. The results are shown for a 100 mVPP signal at the deselected input, and are not normalized to
the gain of the OPS. When the external input of the OPS is selected, add a low-pass filter between the DAC and
the D2S inputs to reduce the feedthrough of the DAC high-frequency content .
-50
-60
-70
-90
-70
-90
OPS Gain = 2.5 V/V
OPS Gain =10 V/V
10M
100M
Frequency (Hz)
1G
-100
1M
D506
OPS Gain = 2.5 V/V
OPS Gain =10 V/V
10M
100M
Frequency (Hz)
1G
D507
PATHSEL > 1.3 V,
100 mVPP signal to VREF (pin 14) with D2S inputs grounded
PATHSEL < 0.7 V,
100 mVPP signal to VIN (pin 9)
Figure 8-12. Forward Feedthrough With OPS
Enabled, Internal Path Selected
44
-60
-80
-80
-100
1M
-50
Figure 8-13. Forward Feedthrough With OPS
Enabled, External Path Selected
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
8.3.3.4 Driving Capacitive Loads
The OPS can drive heavy capacitive loads very well, as shown in Series Output Resistance vs Load
Capacitance to Pulse Response. All high-speed amplifiers benefit from the addition of an external series resistor
to isolate the load capacitor from the feedback loop. Not using a series isolation resistor often leads to response
peaking and possibly oscillation. If frequency response flatness under capacitive load is the design goal, use
slightly higher RF values at the lower gains. Target a slightly-higher feedback transimpedance to increase the
nominal phase margin before the capacitive load acts to decrease it. Using a higher RF value increases the
frequency response flatness across a range of capacitive loads using lower external series resistor values.
Although the suggested RF and RG values of Table 8-1 apply when driving a 100 Ω load, if the intended load is
capacitive (for example, a passive filter with a shunt capacitor as the first element, another amplifier, or a Piezo
element), use the values reported in Table 8-6 as a starting point. The values in Table 8-6 were used to generate
Series Output Resistance vs Load Capacitance and Frequency Response vs Load Capacitance. The results
come from a nominal total feedback transimpedance target of 405 Ω (versus 351 Ω used for Table 8-3), and
includes the internal 18.5 kΩ resistor in the design. Table 8-6 finds the least error to target gain in the selection
of standard resistor values, and limits the minimum RG to 20 Ω. The gains calculated here put 18.5 kΩ in parallel
with the reported external standard value RF.
Table 8-6. Suggested RF and RG Over Gain When Driving a Capacitive Load
CALCULATED GAIN
TARGET GAIN
(V/V)
BEST RF
(Ω)
BEST RG (Ω)
(V/V)
(dB)
GAIN ERROR
(%)
1.5
487
953
1.494
3.488
–0..389
2
432
422
1.995
6
–0.233
2.5
402
261
2.501
7.963
0.048
3
332
162
3.006
9.559
0.191
3.5
274
107
3.515
10.917
0.416
4
221
73.2
3.974
11.984
–0.662
4.5
165
46.4
4.513
13.090
0.295
5
158
39.2
4.984
13.952
–0.320
5.5
165
36.5
5.467
14.755
–0.602
6
169
33.2
6.029
15.605
0.486
6.5
169
30.1
6.547
16.321
0.729
7
174
28.7
6.989
16.888
–0.161
7.5
174
26.7
7.437
17.429
–0.833
8
178
24.9
8.060
18.127
0.753
8.5
178
23.2
8.578
18.668
0.915
9
178
22.1
8.955
19.041
–0.499
9.5
182
21
9.558
19.608
0.613
10
187
20.5
10.006
20.005
0.056
As the capacitive load or amplifier gain increases, the series resistor values can be reduced to hold a flat
response (see Series Output Resistance vs Load Capacitance). See Frequency Response vs Load Capacitance
for the measured SSBW shapes for various capacitive loads configured with the suggested series resistor from
the output of the OPS and the RF and RG values suggested in Table 8-6 for a gain of 2.5 V/V. This measurement
includes a 200 Ω shunt resistor in parallel with the capacitive load as a measurement path.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
45
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
HD2 vs Load Capacitance and HD3 vs Load Capacitance demonstrate the OPS harmonic distortion
performance when driving a range of capacitive loads. These figures show suitable performance for large-signal,
piezo-driver applications. If voltage swings higher than 12 VPP are required, consider driving the OPS output into
a step-up transformer. The high peak-output current for the OPS supports very fast charging edge rates into
heavy capacitive loads, as shown in the step response plots (see Pulse Response and Pulse Response). This
peak current occurs near the center of the transition time driving a capacitive load. Therefore, the I × R drop to
the capacitive load through the series resistor is at a maximum at midtransition, and 0 V at the extremes (low
dV/dT points). For even better performance driving heavy capacitive loads, consider using the THS3217, a DAC
output amplifier with higher output current and slew rate.
8.3.4 Digital Control Lines
The THS3215 provides two logic input lines that control the input path to the OPS and the OPS power disable
feature; both are referenced to GND (pin 7). The control logic defaults to a logic-low state when the pins are
externally floated. The GND pin must have a dc path to some reference voltage for correct operation. Float the
two logic control lines to enable the OPS and select the internal path connecting the D2S internal output to the
OPS noninverting input. Figure 8-14 shows a simplified internal schematic for either logic control input pin.
+VCC
50 PA
Logic
Control
Input
20 PA
1k
Q1
Q2
17.5 k
19 k
Q3
VCTRL
100
D3
D1
D2
PIN 7
Figure 8-14. Logic Control Internal Schematic
The Q2 branch of the differential pair sets up a switch threshold approximately 1 V greater than the voltage
applied to the GND pin. If the control input is floating or < 0.7 V, the differential-pair tail current diverts to the
100-Ω detector load, and results in an output voltage (VCTRL, shown in Figure 8-14) that activates the desired
mode. The floated pin default voltage is the PNP base current into the 19 kΩ resistor. As the control pin voltage
rises above 1.3 V, the differential-pair current is completely diverted away from the 100 Ω side, thus switching
states.
This unique design allows the logic control inputs to be connected to a single-supply as high as 15.9 V, in order
to hold the inputs permanently high, while still accepting a low ground-referenced logic swing for single-supply
operation. The NPN transistor (Q3) and two diodes (D1 and D2) act as a clamp to prevent large voltages from
appearing across the differential stage.
When the OPS is disabled, both input paths to the OPS are also opened up regardless of the state of PATHSEL
(pin 4).
8.4 Device Functional Modes
Any combination of the three internal blocks can be used separately, or in various combinations. The following
sections describe the various functional modes of the THS3215.
46
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
8.4.1 Full-Signal Path Mode
The full-signal path from the D2S to the OPS is available in various options. Three options are described in the
following subsections.
8.4.1.1 Internal Connection With Fixed Common-Mode Output Voltage
The most basic operation is to ground VREF (pin 14), and use the internal connection from the D2S to the OPS
to provide a differential to single-ended, high-power driver. Figure 8-15 shows the characterization circuit used
for the combined performance specifications.
6V
Ferrite
Bead
16
15
14
13
162
50 k
12
100
1
x1
18.5 k
249
50 k
50
2
49.9
x1
11
+
Differential
VIN
49.9
AV = 5 V/V
To
50-Ÿ /RDG
+
250
3
500
x1
10
18.5 k
49.9
4
9
5
6
7
8
200
Ferrite
Bead
±6 V
Figure 8-15. Differential to Single-Ended, Gain of 5 V/V Configuration
This configuration shows the test circuit used to generate Frequency Response vs Output Voltage. Some of the
key features in this basic configuration include:
1. The power supplies are brought into the OPS first, then back to the input stage through a π-filter comprised
of a ferrite bead and local decoupling capacitors on –VCC2 and +VCC2 (pins 5 and 16, respectively). See
the Section 10 section for more information.
2. The two logic lines are grounded. This logic configuration (with pin 7 grounded) selects the internal path from
the D2S to OPS, and enables the OPS.
3. The external I/O pins of the midscale buffer are left floating.
4. The VREF pin is grounded, thus setting the D2S output common-mode voltage at VO1 (pin 6) to ground.
5. The D2S external output is loaded with a 200 Ω resistor to ground. Lighter loading on the VO1 pin (versus
the 100 Ω used to characterize the D2S only) results in increased frequency response peaking. Heavier
loading degrades the D2S distortion performance.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
47
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
6. The external OPS input at VIN+ (pin 9) is left floating. However, VIN+ is internally tied to ground by the
internal 18.5 kΩ resistor.
7. The feedback resistor in the OPS is set to the parallel combination of the external 249 Ω resistor and the
internal 18.5 kΩ resistor. This 245.7 Ω total RF with the 162 Ω RG resistor results in a gain of approximately
2.5 V/V (7.98 dB) in the OPS.
8. The input D2S provides a gain of 2 V/V (6 dB), and along with the 2.5 V/V (7.98 dB) from the OPS, results in
an overall gain of 5 V/V (13.98 dB) with > 600 MHz of SSBW (see Frequency Response vs Output Voltage).
8.4.1.2 Internal Connection With Adjustable Common-Mode Output Voltage
The simplest modification to this starting configuration is using the midscale buffer to drive the VREF pin with
either a dc or ac source into VMID_IN (pin 1), shown in Figure 8-16.
Ferrite
Bead
6V
VMID_OUT
16
15
14
13
162
50 k
12
100
1
+
±
x1
VMID_IN
18.5 k
249
50 k
50
2
49.9
x1
+
Differential
VIN
49.9
11
AV = 5 V/V
To
50-Ÿ /RDG
+
250
3
500
x1
10
18.5 k
49.9
4
9
5
6
7
8
200
Ferrite
Bead
±6 V
Figure 8-16. Differential to Single-Ended, Gain of 5 V/V Configuration With VREF Driven by the Midscale
Buffer
48
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
The VREF input is used to offset the output of the D2S that is then amplified by the OPS. Correct the total dc
offset at the output of the OPS by adjusting the voltage at VMID_IN (pin 1). Use the on-chip midscale buffer as a
low-impedance source to drive the correction voltage to the VREF pin. A wideband small-signal source can also
be summed into this path with a gain of 1 V/V to the D2S output pin. Frequency Response vs Output Voltage
shows the midscale buffer to have an extremely flat response through 100 MHz for < 100 mVPPswings, while 1
VPP is supported through 20 MHz with a flat response.
From this point on, the diagrams are simplified to not show the power-supply elements. However, the supplies
are required by any application, as described in the Section 9 section.
8.4.1.3 External Connection
In the configuration shown in Figure 8-17, the bias to PATHSEL (pin 4) is changed in order to select the external
input of the OPS. The external D2S output drives a low insertion loss, third-order Bessel filter. The filter in this
example is designed with a low frequency insertion loss of 1.55 dB and f–3dB = 50 MHz, and results in an
additional insertion loss of 1 dB at 30 MHz. The OPS gain is slightly increased to recover the filter loss, in order
to give an input to output gain of 5 V/V. Using an interstage filter between the D2S and the OPS improves the
step response by reducing the overshoot. The filter in this example has a relatively low cutoff frequency but if the
application requires it, use a filter with a higher cutoff frequency.
16
15
14
13
102
50 k
12
100
1
x1
18.5 k
205
50 k
50
Differential
VIN
49.9
x1
+
2
49.9
11
AV= 5 V/V
+
250
3
To
50-Ÿ /RDG
500
x1
10
18.5 k
49.9
VPATHSEL > 1.3 V
4
9
1-dB loss
at 30 MHz
464
5
6
7
90.9
8
50-MHz, Low Insertion Loss
3rd-Order Bessel Filter
250 nH
11 pF
56 pF
Figure 8-17. External Path Configuration With Interstage Low-Pass Filter
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
49
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
8.4.2 Dual-Output Mode
The D2S is also used to directly drive a doubly-terminated line, as shown in Figure 8-18. In addition, the OPS
amplifies the internal D2S output by 5 V/V. The internal path to the OPS is selected with PATHSEL (pin 4) at
ground, and the OPS gain is increased to 5 V/V. A 2 VPP output at VO1 produces a 10 VPP output at VOUT (pin
11). This 10 VPP swing requires higher supply operation to provide sufficient headroom in the OPS output stage
in order to preserve signal integrity. A power supply of ±7.5 V provides adequate headroom.
16
15
14
13
39.2
50 k
12
100
1
x1
18.5 k
158
50 k
50
2
49.9
x1
11
+
Differential
VIN
49.9
AV = 10 V/V
To
50-Ÿ /RDG
+
250
3
500
x1
10
18.5 k
49.9
4
9
5
6
7
AV = 2 V/V
8
To
50-Ÿ /RDG
49.9
Figure 8-18. Dual-Output Mode
A simple modification to the circuit in Figure 8-18 is to disable the OPS. The D2S output at VO1 can then be
used either directly or through a filter to an even higher power driver, such as the ±15 V THS3091.
8.4.3 Differential I/O Voltage Mode
Having two amplifiers available also allows a simple differential I/O implementation with independent output
common-mode control, as shown in Figure 8-19. In this configuration, the D2S provides one side of the
differential output, while simultaneously driving the OPS configured in an inverting gain of –1 V/V to provide
the differential output on the other side. The output at VMID_OUT (pin 15) biases the external noninverting input,
VIN+ (pin 9). This circuit configuration places the differential input to the output filter at a common-mode voltage,
VMID_OUT.
50
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
VMID_OUT
VO1
16
15
14
13
280
50 k
12
100
1
+
±
x1
VMID_IN
18.5 k
287
50 k
50
Differential
VIN
x1
+
2
49.9
11
VOUT
+
250
3
Differential
Filter
Differential
Input Mixer
500
x1
10
18.5 k
49.9
VPATHSEL > 1.3V
4
9
5
6
7
VMID_OUT
8
VO1
Figure 8-19. Differential I/O Configuration With Independent Output Common-Mode Voltage Control
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
51
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
9 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification,
and TI does not warrant its accuracy or completeness. TI’s customers are responsible for
determining suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
9.1 Application Information
9.1.1 Typical Applications
The five example designs presented show a good, but not comprehensive, range of the possible solutions that
the THS3215 provides. Numerous more configurations are clearly possible to the creative designer.
9.1.1.1 High-Frequency, High-Voltage, Dual-Output Line Driver for AWGs
6V
6V
16
15
14
13
102
50 k
12
OPS AV= 2.96 V/V
100
1
x1
18.5 k
Either 2.5 VPP
or
10 VPP at Load
203
50 k
50
49.9
x1
+
2
VO
11
VOUT= 5 VPP
To
50-Ÿ /RDG
+
Differential
Filter
250
3
25-MHz, 3rd-order
Bessel filter
500
x1
10
18.5 k
39 pF
49.9 Ÿ
270 nH
VPATHSEL = 3.3 V
4
9
+15V
10
+
5
6
7
8
10
±6 V
200 pF
402
±
THS3095
AV= 3.8 V/V
THS3095
-15V
1.2 k
±6 V
50-MHz, 3rd-order Bessel filter
432
250 nH
90.9
11 pF
52 pF
464
Figure 9-1. Dual-Channel Design: 5 VPP at THS3215 Output and 20 VPP at THS3095 Output
9.1.1.1.1 Design Requirements
For this design example, use the parameters listed in Table 9-1 as the input parameters.
Table 9-1. Dual-Output Design Specifications
52
DESIGN PARAMETER
EXAMPLE VALUE
High-frequency, THS3215 channel
5 VPP, 50 MHz bandwidth
High-voltage, THS3095 channel
20 VPP, 25 MHz bandwidth
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
9.1.1.1.2 Detailed Design Procedure
The THS3215 is well suited for high-speed, low-distortion arbitrary waveform generator (AWG) applications
commonly used in laboratory equipment. In this typical application, a high-speed, complementary-current-output
DAC is used to drive the D2S. The OPS of the THS3215 easily drives a 50 MHz, 2.5 VPP signal into a matched
50 Ω load. When a larger output signal is required, consider using the THS3095 as the final driver stage.
A passive RLC filter is commonly used on DAC outputs to reduce the high-frequency content in the DAC
steps. The filtering between the DAC output and the input to the D2S reduces higher-order DAC harmonics
from feeding into the internal OPS path when the external input path is selected. Feedthrough between the
internal and external OPS paths increases with increasing frequency; however, the input filter rolls off the DAC
harmonics before the harmonics couple to VOUT (pin 10) through the deselected OPS signal path. Figure 9-2
shows an example of a doubly-terminated differential filter from the DAC to the THS3215 D2S inputs at +IN (pin
2) and –IN (pin 3). The DAC is modeled as two, fixed, 10 mA currents and a differential, ac-current source. The
10 mA dc midscale currents set up the average common-mode voltage at the DAC outputs and D2S inputs at
10 mA × 25 Ω = 0.25 VCM. The total voltage swing on each DAC output is 0 V to 0.5 V.
Complementary
Output DAC
D2S Stage with input
capacitance included
10 mA
IN+
150 nH
2
49.9
30 pF
27 pF
49.9
2.4 pF
27 pF
49.9
2.4 pF
IDIFF
150 nH
3
10 mA
49.9
30 pF
IN-
Figure 9-2. 105 MHz Butterworth Filter Between DAC and D2S Inputs
Some of the guidelines to consider in this filter design are:
1. The filter cutoff is adjusted to hit a standard value in the standard high-frequency, chip inductors kits.
2. The required filter output capacitance is reduced from the design value of 29.4 pF to 27 pF to account for the
D2S input capacitance of 2.4 pF, as reported in the D2S Electrical Characteristics table.
3. The capacitor at the DAC output pins must also be reduced by the expected DAC output pin capacitance.
The DAC output capacitance is often specified as 5 pF, but is usually much lower. Contact the DAC
manufacturer for an accurate value.
Figure 9-3 shows the TINA-simulated filter response for the input-stage filter. The low-frequency 34 dBΩ gain is
due to the 50 Ω differential resistance at the DAC output terminals. At 200 MHz, this filter is down 17 dB from the
50 Ω level; it is also very flat through 50 MHz.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
53
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
35
Filter Response (dB:)
30
25
20
15
10
5
0
1M
10M
100M
Frequency (Hz)
1G
D508
Figure 9-3. Simulated, Differential-Input Filter Response
In the example design of Figure 9-1, a 50 MHz, third-order Bessel filter is placed between the D2S output
and the external OPS input. Another 25 MHz, third-order Bessel filter is placed at the input of a very-high
output-swing THS3095 stage. A double-pole, double-throw (DPDT) relay selects the THS3095 path when the
internal OPS path is selected in the THS3215. Figure 9-1 shows this design. The key operational considerations
in this design include:
1. When the external input OPS path is selected, the 2 VPP maximum D2S output swing experiences a 1.55
dB insertion loss from the interstage filter between VO1 (pin 6) and VIN+ (pin 9). A standard value inductor
is used and the 464 Ω termination accounts for the internal 18.5 kΩ element. The 10 Ω resistor at VIN+
isolates the OPS input from the 52 pF filter capacitor. To recover the insertion loss and produce a maximum
5 VPP output, the OPS gain is set to 2.96 V/V. When the interstage filter path is selected, the two DPDT
relays pass the OPS output on directly from the 49.9 Ω output matching resistor to VO. Disable the THS3095
to conserve power.
2. To deliver 20 VPP at the VO output, select the THS3095 path. Select the internal OPS path to bypass the
50 MHz filter (1.55 dB insertion loss) in order to give a maximum 5.9 VPP output at VOUT (pin 11). The two
DPDT relays switch position, and the 49.9 Ω at the OPS output becomes part of the 25 MHz, third-order
Bessel filter into the THS3095 stage. This filter has a 1 dB insertion loss requiring a gain of 3.8 V/V in the
THS3095 to deliver 20 VPP from the OPS output.
3. Frequency Response of the 5 VPP and 20 VPP Channels and Harmonic Distortion Performance of the 5
VPP and 20 VPP Channels show the frequency response and harmonic distortion performance of the dual
output-voltage system. The frequency response is normalized to 0 dB to make bandwidth comparisons
easier.
9.1.1.1.3 Application Curves
3
-40
5 VPP
20 VPP
-50
-3
Distortion (dBc)
Normalized Gain (dB)
0
-6
-9
10M
Frequency (Hz)
100M
200M
D509
Figure 9-4. Frequency Response of the 5 VPP and
20 VPP Channels
54
-70
-80
HD2 -5 VPP
HD3- 5 VPP
HD2- 20 VPP
HD3- 20 VPP
-90
-12
-15
1M
-60
-100
1M
10M
Frequency (Hz)
D510
Figure 9-5. Harmonic Distortion Performance of
the 5 VPP and 20 VPP Channels
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
9.1.1.2 High-Voltage Pulse-Generator
7.5 V
7.5 V
16
15
14
13
102
50 k
OPS AV= 3 V/V
12
100
1
x1
18.5 k
205
50 k
1V
50
2
x1
100
0 to 10 mA
250
3
5 VPP Max
at Load
11
VOUT= 10 VPP
+
1V
0V
49.9
+
0 to 10 mA
0V
To
50-Ÿ /RDG
500
x1
10
18.5 k
100
VPATHSEL = 3.3 V
4
9
5
6
7
1.55-dB
insertion loss
8
10
±7.5 V
±7.5 V
35-MHz, 3rd-order Bessel filter
390 nH
100
13 pF
75 pF
511
Figure 9-6. Driving a 10 VPP Pulse Output into a 100 Ω Load With a 35 MHz External Interstage Bessel
Filter
9.1.1.2.1 Design Requirements
To design a high-voltage, high-speed pulse generator with minimum overshoot, use the parameters listed in
Table 9-1 as the input parameters.
Table 9-2. Pulse-Generator Specifications
DESIGN PARAMETER
EXAMPLE VALUE
Power supply
±7.5 V
Pulse frequency
5 MHz
Pulse output voltage
10 VPP
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
55
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
9.1.1.2.2 Detailed Design Procedure
Figure 9-6 shows an example design using the THS3215 to deliver a 10 VPP maximum voltage from a DAC
input, and includes an example external, third-order, interstage Bessel filter. Some of the salient considerations
for this design include:
1. Termination resistance at the D2S inputs is increased to reduce DAC output current. This example is
intended to be used with a current-sourcing DAC with an output compliance voltage of at least 1 V on a
0.5 V common-mode voltage. The 10-mA, single-ended, DAC tail current produces a 0 V to 1 V swing on
each 100 Ω termination. The resulting 2 VPP differential DAC signal produces a higher SNR signal at the
THS3215 inputs.
2. The midscale buffer is not used. VREF (pin 14) is grounded to set the inputs to a 4-VPP ground-centered
maximum output swing at VO1 (pin 6). The external input to the OPS is selected by setting PATHSEL (pin 4)
to 3.3 V (anything over 1.3 V is adequate, or tie this pin to +VCC for fixed, external-path operation).
3. The interstage Bessel filter is –0.3 dB flat through 12 MHz, with only 1.55 dB of insertion loss. The filter is
designed to be low insertion-loss with relatively high resistor values. The filter uses standard inductor values.
The capacitors are also standard-value, and slightly off from the exact filter solution. The final resistor to
ground is designed for 500 Ω, but increased here to a standard 511 Ω externally to account for the internal
18.5 kΩ resistor on the external OPS input pin to GND. To isolate the last 75 pF filter capacitor from the OPS
input stage, a 10 Ω series resistor is added close to the VIN+ (pin 9) input.
4. The filter adds 1.55 dB of insertion loss that is recovered, to achieve a 10 VPP maximum output by designing
the OPS for a gain of 3 V/V. Looking at Table 8-6, this gain setting requires the 205 Ω external RF and 102 Ω
RG to ground for best operation.
5. For 10 VPP maximum output, the ±7.5 V supplies shown in Figure 9-6 give adequate headroom in the OPS
output stage. The operating maximum supply of 15.8 V requires a 5% tolerance on these ±7.5 V supplies.
6. The Bessel filter gives a very low overshoot full-scale output step-response, as shown in the 5 MHz, ±5 V
square wave of Pulse Response of the System With the Interstage Bessel Filter. The frequency response of
the system is shown in Frequency Response of the System With the Interstage Bessel Filter.
9.1.1.2.3 Application Curves
16
6
10 VPP
r5 V
14
Output Voltage (V)
4
Gain (dB)
12
10
8
6
4
1M
0
-2
-4
-6
10M
Frequency (Hz)
100M
Time (20 ns/div)
D511
Figure 9-7. Frequency Response of the System
With the Interstage Bessel Filter
56
2
D512
Figure 9-8. Pulse Response of the System With the
Interstage Bessel Filter
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
9.1.1.3 Single-Supply, AC-Coupled, Piezo Element Driver
VMID_OUT
VMID_OUT
15 V
15 V
16
15
14
13
75
50 k
12
OPS AV = 3.4 V/V
100
1
x1
1 …F
18.5 k
182
50 k
10 nF
5.9
50
x1
+
2
1.62 k
49.9
VMID_OUT
VOUT = 12 VPP
220 pF
+
2 VPP
1.62 k
49.9
11
250
3
500
x1
10
18.5 k
10 nF
(VMID_OUT + 3.5 VPP)
VPATHSEL=15 V
4
9
5
6
7
8
10
VO1 = VMID_OUT + 4 VPP
105
390 nH
15-MHz, 2nd-order Chebyshev
filter (0.2 dB ripple)
825
68 pF
1 …F
Figure 9-9. Single-Supply, Heavy Capacitive-Load Driving
9.1.1.3.1 Detailed Design Procedure
The very-high peak output current and slew rate of the THS3215 OPS make it particularly suitable for driving
heavy capacitive loads, such as the piezo elements used in continuous wave (CW) applications that require
high-amplitude, sinusoidal-type excitations. The driver is quickly disabled during the receive time when the
output transmit and receive switch is moved to receive mode. Figure 9-9 shows an example design using the
internal midscale buffer to bias all the stages to midsupply on a single 15 V design. There are many elements to
this example that also apply to any single-supply application. The key points here are:
1. The differential DAC input signal is ac-coupled to the D2S input, and the termination resistors are scaled up
and biased to midsupply using the output of the midscale buffer, VMID_OUT (pin 15). The 10-nF blocking
capacitors before the 1.62 kΩ termination resistors set the high-pass pole at 10 kHz.
2. The internal divider resistors of the midscale buffer are decoupled using a 1 µF capacitor on VMID_IN (pin
1). Use of the capacitor improves both noise and PSRR through the reference buffer stage. In turn, the noise
injected by the bias source is reduced at the various places the buffer output is used.
3. VMID_OUT is also applied to the VREF input (pin 14) to hold the D2S output centered on the single 15
V supply. There is minimal dc current into VREF because the D2S input buffers operate at the same
common-mode voltage, VMID_OUT.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
57
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
4. The D2S output is dc biased at midsupply and delivers two times the differential swing applied at its inputs.
Assuming 2 VPP at the D2S inputs implies 4 VPP at the D2S output pins. Lower input swings are supported
with the gain in the OPS adjusted to meet the desired output maximum.
5. The filter in Figure 9-9 is a 0.2 dB ripple, second-order Chebyshev filter at 15 MHz. For example, if
the desired maximum frequency is 12 MHz, this filter attenuates the HD2 and HD3 out of the D2S by
approximately 3 dB and 5 dB, respectively. Increased attenuation can be provided with higher-order filters,
but this simple filter does a good job of band-limiting the high-frequency noise from the D2S outputs before
the noise gets into the OPS.
6. The dc bias voltage at VO1 (pin 6) drives a small dc current into the 18.5 kΩ resistor to ground at the OPS
external input, VIN+ (pin 9). The error voltage due to the bias current level-shifts the dc voltage at the OPS
noninverting input through the 105 Ω filter resistor. This offset is amplified by the OPS gain because the RG
element is referenced to the VMID output with a dc gain of 3.4 V/V.
7. The logic lines are still referenced to ground in this single-supply application. The external path to the OPS
is selected by connecting PATHSEL (pin 4) to +VCC. DISABLE (pin 10) is grounded in this example in order
to hold the OPS on. If the disable feature is required by the application, drive DISABLE (pin 10) using a
standard logic control driver. Note that the midscale buffer output still drives RG and RF to midsupply in this
configuration with the OPS disabled.
8. To operate at midsupply, ac-couple the RG element to ground through a capacitor. Figure 9-9 shows the
midscale buffer driving RG, thus eliminating the need for an added capacitor. Use a blocking capacitor to
move the dc gain to 1 V/V. The voltage on the external, noninverting input of the OPS sets the dc operating
point. Use a blocking capacitor to lighten the load on the midscale buffer output and eliminate the bias on RG
when the OPS is disabled.
9. Piezo element drivers operate in a relatively low-frequency range; therefore, the OPS RF is scaled up even
further than the values suggested in Table 8-6. An increased RF allows RG to also be scaled up, thereby
reducing the load on the midscale buffer, and allow a lower series output resistor to be used into the 220 pF
capacitive load.
10. The peak charging current into the capacitive load occurs at the peak dV/dT point. Assuming a 12 MHz
sinusoid at 12 VPP requires a peak output current from the OPS of 6 VPEAK × 2π × 12 MHz × 220 pF =
100 mA. This result is slightly lesser than the rated minimum peak output current of the OPS.
Using a very low series resistor limits the waveform distortion due to the I × R drop at the peak charging
point around the sinusoidal zero crossing. The 100 mA through 5.9 Ω causes a 0.59 V peak drop to the load
capacitance around zero crossing. The voltage drop across the series output resistor increases the apparent
third harmonic distortion at the capacitive load. HD2 vs Load Capacitance and HD3 vs Load Capacitance show
10 VPP distortion sweeps into various capacitor loads. The results shown in these figures are for the OPS only
because the results set the harmonic distortion performance in this example.
58
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
9.1.1.4 Output Common-Mode Control Using the Midscale Buffer as a Level Shifter
VMID_OUT
VO1
7.5 V
7.5 V
16
15
14
13
51.1
50 k
12
100
1
VMID_IN = ±2 V
x1
+
±
18.5 k
205
50 k
50
2
x1
+
49.9
11
VMID_OUT ±4 V
AV = ±4 V/V
+
1 VPP
250
3
500
x1
10
18.5 k
49.9
VPATHSEL > 1.3V
4
9
5
±7.5 V
6
7
VO1= VMID_OU T ±1 V
VMID_OUT
8
±7.5 V
Figure 9-10. Adding an Output DC Offset Using the Midscale Buffer
9.1.1.4.1 Detailed Design Procedure
An easy way to insert a dc offset into the signal channel (without sacrificing any of the DAC dynamic range) is
to apply the desired offset at VMID_IN (pin 1) and use it to bias VREF (pin 14) and VIN+ (pin 9). An example
is shown in Figure 9-10. This example shows a relatively low maximum differential input of 1 VPP on any
compliance voltage required by the DAC. Other configuration options include:
1. The D2S output is offset using a dc input at VMID_IN. Although shown here as ±2 V, the dc range expands
to ±3.5 V when using ±7.5 V supplies.
2. Connect VMID_OUT (pin 15) to the VREF input to place the D2S output at the dc offset voltage along with
a gain of 2 V/V version of the differential input voltage. The stated range of ±2 V, along with the ±0.5 V out
of the upper input buffer, requires a peak output current from VMID_OUT of 2.5 V / 150 Ω = 16.7 mA. This
value is well below the rated minimum linear output current of 40 mA for the midscale buffer.
3. The dc offset voltage is then applied to the external OPS non-inverting input, VIN+. Connecting the circuit
in this manner results in no additional dc gain for the dc offset between the D2S and OPS outputs, while
continuing to retain the signal gain of the OPS configured as an inverting amplifier. The values of RF and
RG in this application example are derived from Table 8-3. The OPS is setup for a gain of –4 V/V in this
example. Using the resistor values from Table 8-3 results in the widest bandwidth for the OPS; however, the
RG = 51.1 Ω resistor presents a heavy load to the D2S output. In such cases, the OPS external resistors can
be scaled up to reduce the D2S output load, but at the expense of reduced OPS bandwidth.
4. No filtering is shown in this example; however, introducing filtering in the OPS RG path is certainly possible.
In such cases, the RG element is also the filter termination resistor. Filtering adds insertion loss that can be
recovered by adjusting the OPS gain setting.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
59
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
9.1.1.5 Differential I/O Driver With independent Common-Mode Control
VMID_OUT
VO1
16
15
14
13
294
50 k
12
100
1
+
±
x1
VMID_IN
18.5 k
294
50 k
50
Differential
VIN
x1
+
2
11
VOUT = VMID_OUT ± 2VIN
49.9
+
250
3
Differential
Filter
Differential
Input Mixer
500
x1
10
18.5 k
49.9
4
VPATHSEL > 1.3 V
9
6
5
7
VMID_OUT
8
VO1= VMID_OUT + 2VIN
Figure 9-11. Differential I/O with Common-Mode Control
9.1.1.5.1 Detailed Design Procedure
Certain applications require the differential DAC output voltage to be translated from one common-mode
(compliance) level to a differential output at a different common-mode level. The THS3215 performs voltagelevel translation directly using the very flexible blocks provided internally. Figure 9-11 shows an example of such
an application, where the differential gain is always 4 V/V. The differential gain is fine-tuned down by setting the
insertion loss in the differential post-filter. The considerations critical to this application include:
1. The input is dc-coupled with the appropriate termination impedance required by the DAC. Use a highfrequency, antialiasing filter at the input to limit DAC feedthrough in the deselected OPS internal input.
2. The output common-mode control is set with the voltage applied to the VMID buffer input at VMID_IN (pin 1).
The circuit is configured so that the output at VMID_OUT (pin 15) drives both VREF (pin 14), in order to set
the D2S dc output voltage, and VIN+ (pin 9).
3. The D2S output available at VO1 (pin 6) provides one side of the differential-output, and is dc-biased at
VMID_OUT. VO1 also drives the RG resistor for the OPS in an inverting gain of –1 V/V. The dc bias level
at the RG input and the VIN+ input of the OPS are the same voltage; therefore, no level shift through the
OPS occurs. The OPS outputs an inverted version of the D2S output signal at the same common-mode
voltage (VMID_OUT). The wideband, differential signal with independent output common-mode voltage control
can now be applied to a differential filter and on to the next stage.
4. Make sure that the differential filter has only differential resistors and capacitors. Termination resistors to
ground level-shift the input common-mode voltage, while differential resistors transfer VMID_OUT directly
through the filter as a common-mode input to the mixer.
5. If the desired VMID_OUT + differential signal combined clips in the OPS or D2S, offset the supplies to gain
headroom. For instance, if a 5 V output common-mode voltage is required with a 10 VPP differential signal,
the OPS and D2S must deliver 2.5 V to 7.5 V output swings. The D2S has the higher headroom requirement
at 1.5 V (maximum). Operating the THS3215 with –5 V and 10 V supplies stays within the rated maximum of
15.8 V total supply range, and provide adequate headroom for the positive offset swing requirement. Note
that the logic lines are still referenced to GND by pin 7. Tie PATHSEL (pin 4) to +VCC to hold this design in
the external path mode required.
60
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
10 Power Supply Recommendations
The THS3215 typically operates on balanced, split supplies. The specifications and characterization plots use
±6 V in most cases. The full operating range for the THS3215 spans ±4 V to ±7.9 V. The input and output stages
have separate supply pins that are isolated internally.
The recommended external supply configuration brings ±VCC into the output stage first, then back to the input
stage connections through a π-filter comprised of ferrite beads and added decoupling capacitors at +VCC2 (pin
16) and –VCC2 (pin 5). Figure 10-1 shows an example decoupling configuration. This same circuit configuration
was used to characterize the D2S + OPS performance in Frequency Response vs Output Voltage to HD3 vs
Supply Voltage.
Ferrite Bead
4 H
Ferrite Bead
4 H
6V
2.2 …F
10 nF
16
10 nF
220 nF
15
14
220 nF
13
162
50 k
12
100
1
x1
18.5 k
249
50 k
50
2
49.9
x1
11
+
Differential
VIN
49.9
AV = 5 V/V
To
50-Ÿ /RDG
+
250
3
500
x1
10
18.5 k
49.9
4
9
5
6
7
8
200
Ferrite Bead
4 H
Ferrite Bead
4 H
-6 V
2.2 …F
10 nF
220 nF
10 nF
220 nF
Figure 10-1. Recommended Power-Supply Configuration
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
61
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
The ferrite bead acts to break the feedback loop from the output stage load currents that re-enter the D2S and
midscale buffer stages. Operate the two positive supply pins and the two negative supply pins at the same
voltage. Using separate sources on the two pins risks forward-biasing the on-chip parallel diodes that connect
the two supply inputs together. +VCC1 (pin 13) and +VCC2 (pin 16) have two parallel diodes that are off if the
voltage at the two pins are equal. The same is true for –VCC1 (pin 8) and –VCC2 (pin 5).
The THS3215 provides considerable flexibility in the supply voltage settings. The overriding consideration is
always satisfying the required headroom to the supplies on all the I/O paths. The logic controls on PATHSEL (pin
4) and DISABLE (pin 10) are intended to operate ground referenced regardless of supplies used. The ground
connection on pin 7 is used to set the reference.
Power savings are certainly possible by operating with only the minimum required supplies for the intended
swings at each of the pins. For instance, consider an example design operating with a current-sinking DAC with
the input common-mode voltage at 3 V, with an output swing at the D2S output of ±1 V. Looking at just the D2S
under these conditions, the minimum positive supply is 3 VCM + the maximum input headroom of 1.5 V to the
positive supply + the input signal swing of 0.25 V, resulting in a minimum 4.75 V supply for this operation. The
±1 V output at VO1 (pin 6) along with the D2S output headroom sets the minimum negative supply voltage.
The maximum 1.5 V headroom gives a possible minimum negative supply of –2.75 V. However, the minimum
operating total of 8 V increases the negative supply to –3.5 V.
If the ±1 V swing is then amplified by the OPS, the output swing and headroom requirements set the minimum
operating supply. For instance, if the OPS is operating at a gain of 2.5 V/V, the ±2.5 V output requires a
maximum headroom of 1.6 V to either supply. Achieving a 1.6 V headroom requires a minimum balanced supply
of ±4.1 V. However, the input stage overrides the positive side because the required minimum is 4.75 V, while
the negative increases to –4.1 V. This example of absolute minimum supplies saves power. Using a typical
35-mA quiescent current for all stages, going to the minimum 8.5 V total across the device, uses 310 mW of
quiescent power versus the 420 mW if a simple ±6 V supply is applied. However, ac performance degrades
with the lower headroom. For more power-sensitive applications, consider adjusting the supplies to the minimum
required on each side.
10.1 Thermal Considerations
The internal power for the THS3215 is a combination of its quiescent power and load power. The quiescent
power is simply the total supply voltage times the supply current. This current is trimmed to reduce power
dissipation variation and minimize variations in the ac performance. At a ±7.5 V supply, the maximum supply
current of 36.5 mA dissipates 548 mW of quiescent power. The worst-case load power occurs if the output is
at ½ the single-sided supply voltage driving a dc load. Placing a ±3.75 V dc output into 100 Ω adds another
37.5 mA × 3.75 V = 140 mW of internal power. This total of approximately 688 mW of internal dissipation
requires the thermal pad be connected to a good heat-spreading ground plane to hold the internal junction
temperatures below the rated maximum of 150°C.
The thermal impedance is approximately 45 °C/W with the thermal pad connected. For 688 mW of internal
power dissipation there is a 31°C (approximate) rise in the junction temperature from ambient. Designing for the
intended 85°C maximum ambient temperature results in a maximum junction temperature of 116°C.
62
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
11 Layout
11.1 Layout Guidelines
High-speed amplifier designs require careful attention to board layout in order to achieve the performance
specified in the data sheets. Poor layout techniques can lead to increased parasitics from the board and external
components resulting in suboptimal performance, and also instability in the form of oscillations. The THS3215
evaluation module (EVM) serves as a good reference for proper, high-speed layout methodology. The EVM
includes numerous extra elements needed for lab characterization, and also additional features that are useful
in certain applications. These additional components can be eliminated on the end system if not required by the
application. General suggestions for the design and layout of high-speed, signal-path solutions include:
1. Minimize parasitic capacitance to any ac ground for all of the signal I/O pins. Parasitic capacitance on the
output and input pins can cause instability. To reduce unwanted capacitance, open a window around the
signal I/O pins on all of the ground and power planes around those pins. On other areas of the board,
continuous ground and power planes are preferred for signal routing, with matched impedance traces for
longer runs.
2. Use high-quality, high-frequency decoupling capacitors (0.1 µF) on the ground plane at the device power
pins. Higher value capacitors (2.2 µF) are required, but can be placed further from the device power pins
and shared among devices. For best high-frequency decoupling, consider X2Y supply-decoupling capacitors
that offer a much higher self-resonance frequency over standard capacitors. Avoid narrow power and ground
traces to minimize inductance between the pins and the decoupling capacitors. Follow the power-supply
guidelines recommended in the Section 10 section.
3. Careful selection and placement of external components preserve the high-frequency performance of the
THS3215. Use low-reactance type resistors. Surface-mount resistors work best, and allow a tighter overall
layout. Keep the printed circuit board (PCB) trace length as short as possible. Never use wire-bound type
resistors in a high-frequency application. The output pin and inverting input pins are the most sensitive to
parasitic capacitance; therefore, always position the feedback and series output resistors, if any, as close
as possible to the inverting input pins and output pins. Place other network components, such as input
termination resistors, close to the gain-setting resistors.
4. When using differential signal routing over any appreciable distance, use microstrip layout techniques with
matched impedance traces. On differential lines, like those on the D2S inputs, match the routing in order to
minimize common-mode noise effects and improve HD2 performance.
5. The input summing junction of the OPS is very sensitive to parasitic capacitance. Connect the RG element
into the summing junction with minimal trace length to the device-pin side of the resistor. The other side
of RG can have more trace length to source or ground, if needed; however, a very-short, low-inductance
connection is preferred. For best results, do not socket a high-speed device such as the THS3215.
The additional lead length and pin-to-pin capacitance introduced by the socket can create an extremely
troublesome parasitic network that makes it almost impossible to achieve a smooth, stable frequency
response. Best results are obtained by soldering the THS3215 directly onto the board.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
63
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
11.2 Layout Example
Remove ground and power planes
close to VOUT and VINpins to minimize capacitance
Place bypass capacitors
close to power pins
13
14
11
3
10
4
9
Place 50-Ÿ RXWSXW UHVLVWRU FORVH
to VOUT pin to minimize
parasitic capacitance
8
2
7
12
6
Connect thermal pad to GND
Place RF and RG close to device
pins to minimize stray capacitance
and feedback loop area
1
5
Remove ground and power
planes close to D2S inputs
to minimize capacitance
15
16
Ground and power plane
on inner layers
Figure 11-1. Layout Example
64
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
12 Device and Documentation Support
12.1 Device Support
12.1.1 Development Support
12.1.1.1 TINA-TI™ (Free Software Download)
TINA™ is a simple, powerful, and easy-to-use circuit simulation program based on a SPICE engine. TINA-TI is a
free, fully-functional version of the TINA software, preloaded with a library of macro models in addition to a range
of both passive and active models. TINA-TI provides all the conventional dc, transient, and frequency domain
analysis of SPICE, as well as additional design capabilities.
Available as a free download from the Analog eLab Design Center, TINA-TI offers extensive post-processing
capability that allows users to format results in a variety of ways. Virtual instruments offer the ability to select
input waveforms and probe circuit nodes, voltages, and waveforms, creating a dynamic quick-start tool.
The THS3215 TINA model is available on the THS3215 product folder, under the Tools and software tab. After
downloading, open the model, right-click on a model symbol, and select Enter Macro to see the list of modeled
parameters.
Note
These files require that either the TINA software (from DesignSoft™) or TINA-TI software be installed.
Download the free TINA-TI software from the TINA-TI folder.
12.2 Documentation Support
12.2.1 Related Documentation
For related documentation, see the following:
•
•
•
•
•
•
Texas Instruments, OPA695 Ultra-Wideband, Current-Feedback Operational Amplifier With Disable data
sheet
Texas Instruments, THS3215EVM and THS3217EVM user's guide
Texas Instruments, Voltage Feedback Vs Current Feedback Op Amps application report
Texas Instruments, Current Feedback Amplifier Analysis and Compensation application report
Texas Instruments, Current Feedback Amplifiers: Review, Stability Analysis, and Applications application note
Texas Instruments, Stabilizing Current-Feedback Op Amps While Optimizing Circuit Performance application
report
12.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
12.4 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
12.5 Trademarks
TINA-TI™, TINA™, and TI E2E™ are trademarks of Texas Instruments.
DesignSoft™ is a trademark of DesignSoft, Inc.
All trademarks are the property of their respective owners.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
65
THS3215
www.ti.com
SBOS780C – MARCH 2016 – REVISED JUNE 2021
12.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
12.7 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
66
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: THS3215
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
THS3215IRGVR
ACTIVE
VQFN
RGV
16
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
THS3215
IRGV
THS3215IRGVT
ACTIVE
VQFN
RGV
16
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
THS3215
IRGV
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of