TL072-EP, TL074-EP
www.ti.com
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIER
Check for Samples: TL072-EP, TL074-EP
FEATURES
1
•
•
Low Power Consumption
Wide Common-Mode and Differential Voltage
Ranges
Low Input Bias and Offset Currents
Output Short-Circuit Protection
Low Total Harmonic Distortion: 0.003% Typ
Low Noise
Vn = 18 nV/√Hz Typ at f = 1 kHz
High Input Impedance: JFET Input Stage
Internal Frequency Compensation
Latch-Up-Free Operation
High Slew Rate: 13 V/μs Typ
Common-Mode Input Voltage Range Includes
VCC+
•
•
•
•
•
•
•
•
•
TL072
D PACKAGE
(TOP VIEW)
1OUT
1IN−
1IN+
VCC−
1OUT
1IN−
1IN+
VCC+
2IN+
2IN−
2OUT
Controlled Baseline
One Assembly and Test Site
One Fabrication Site
Available in Extended (–40°C to 125°C) or
Military (–55°C to 125°C) Temperature Range
Extended Product Life Cycle
Extended Product-Change Notification
Product Traceability
•
•
•
8
2
7
3
6
4
5
VCC+
2OUT
2IN−
2IN+
TL074
D PACKAGE
(TOP VIEW)
SUPPORTS DEFENSE, AEROSPACE,
AND MEDICAL APPLICATIONS
•
•
•
•
1
1
14
2
13
3
12
4
11
5
10
6
9
7
8
4OUT
4IN−
4IN+
VCC−
3IN+
3IN−
3OUT
DESCRIPTION/ORDERING INFORMATION
The JFET-input operational amplifiers in the TL07x is similar to the TL08x series, with low input bias and offset
currents and fast slew rate. The low harmonic distortion and low noise make the TL07x ideally suited for highfidelity and audio preamplifier applications. Each amplifier features JFET inputs (for high input impedance)
coupled with bipolar output stages integrated on a single monolithic chip.
The TL07x is characterized for operation over the extended temperature range of –40°C to 125°C or military
temperature range of –55°C to 125°C.
ORDERING INFORMATION (1)
TA
VIOmaX
AT 25°C
–40°C to 125°C
6 mV
–55°C to 125°C
(1)
6 mV
PACKAGE
SOIC – D
SOIC – D
Reel of 2500
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
VID NUMBER
TL072QDREP
TL072Q
V62/12604-01XE
V62/11621-01XE
TL074QDREP
TL074Q
Reel of 2500
TL074MDREP
TL074M
V62/11621-02XE
Tube of 75
TL074MDEP
TL074M
V62/11621-02XE-T
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011–2012, Texas Instruments Incorporated
TL072-EP, TL074-EP
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
www.ti.com
TL072 and TL074 SYMBOL (EACH AMPLIFIER)
IN+
+
IN−
−
OUT
SCHEMATIC (EACH AMPLIFIER)
VCC+
IN+
64 Ω
IN−
128 Ω
OUT
64 Ω
C1
18 pF
ÎÎÎ
ÎÎÎ
ÎÎÎ
1080 Ω
1080 Ω
VCC−
All component values shown are nominal.
COMPONENT COUNT (1)
COMPONENT
TYPE
Resistors
Transistors
JFET
Diodes
Capacitors
epi-FET
(1)
2
TL072
TL074
22
28
4
2
2
2
44
56
6
4
4
4
Includes bias and trim circuitry
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: TL072-EP TL074-EP
TL072-EP, TL074-EP
www.ti.com
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
MIN
VCC+
VCC–
MAX
UNIT
18
Supply voltage (2)
V
18
VID
Differential input voltage (3)
±30
V
VI
Input voltage (2)
±15
V
(4)
Duration of output short circuit
(5)
Unlimited
θJA
Thermal resistance, junction-to-ambient (6)
θJC
Thermal resistance, junction-to-case (7)
TJ
Operating virtual junction temperature
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(7)
TL072
97.5
TL074
86
TL072
38.3
TL074
51.5
–65
°C/W
°C/W
150
°C
150
°C
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC−.
Differential voltages are at IN+, with respect to IN−.
The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less.
The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the
dissipation rating is not exceeded.
Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: TL072-EP TL074-EP
Submit Documentation Feedback
3
TL072-EP, TL074-EP
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
VCC± = ±15 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS (1)
VIO
Input offset voltage
VO = 0, RS = 50 Ω
αVIO
Temperature coefficient
of input offset voltage
VO = 0, RS = 50 Ω
IIO
Input offset current
VO = 0
IIB
Input bias current
VICR
Common-mode input
voltage range
VOM
Maximum peak output
voltage swing
TA
TL072
(2)
MIN
TL074
TYP
MAX
25°C
3
Full range
Full range
18
25°C
5
65
125°C
RL ≥ 10 kΩ
±11
–12 to 15
25°C
±12
±13.5
Full range
RL ≥ 2 kΩ
6
3
100
5
200
65
±12
±10
±10
25°C
35
15
100
pA
2
nA
200
pA
20
nA
±11 –12 to 15
±12
200
35
mV
μV/°C
18
±12
Full range
6
8
20
25°C
UNIT
MAX
2
25°C
RL = 10 kΩ
TYP
8
125°C
VO = 0
MIN
V
±13.5
V
200
AVD
Large-signal differential
voltage amplification
B1
Unity-gain bandwidth
25°C
3
3
ri
Input resistance
25°C
1012
1012
Ω
CMRR
Common-mode
rejection ratio
kSVR
VO = ±10 V, RL ≥ 2 kΩ
VIC = VICRmin,
VO = 0, RS = 50 Ω
V/mV
15
MHz
25°C
80
86
80
86
dB
Supply-voltage rejection VCC = ±9 V to ±15 V,
ratio (ΔVCC±/ΔVIO)
VO = 0, RS = 50 Ω
25°C
80
86
80
86
dB
ICC
Supply current (each
amplifier)
VO = 0, No load
25°C
VO1/VO2
Crosstalk attenuation
AVD = 100
25°C
(1)
(2)
1.4
1.4
2.5
120
2.5
120
mA
dB
Input bias currents of an FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive, as
shown in Figure 3. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as
possible.
All characteristics are measured under open-loop conditions with zero common-mode voltage, unless otherwise specified. Full range is
TA = –40°C to 125°C for TL07xQ and TA = -55°C to 125°C for TL07xM.
OPERATING CHARACTERISTICS
VCC± = ±15 V, TA= 25°C
PARAMETER
TEST CONDITIONS
TL072
TL074
MIN
TYP
8
13
MAX
MAX
UNIT
MIN
TYP
8
13
V/μs
μs
SR
Slew rate at unity
gain
VI = 10 V,
CL = 100 pF,
RL = 2 kΩ,
See Figure 1
tr
Rise-time overshoot
factor
VI = 20 V,
CL = 100 pF,
RL = 2 kΩ,
See Figure 1
0.1
0.1
20
20
%
Vn
Equivalent input noise
RS = 20 Ω
voltage
f = 1 kHz
18
18
nV/√Hz
4
4
μV
In
Equivalent input noise
RS = 20 Ω,
current
0.01
0.01
pA/√Hz
THD
Total harmonic
distortion
0.003
0.003
%
4
VIrms = 6 V,
RL ≥ 2 kΩ,
f = 1 kHz,
Submit Documentation Feedback
f = 10 Hz to 10 kHz
f = 1 kHz
AVD = 1,
RS ≤ 1 kΩ,
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: TL072-EP TL074-EP
TL072-EP, TL074-EP
www.ti.com
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
PARAMETER MEASUREMENT INFORMATION
10 kΩ
1 kΩ
−
−
VI
VO
VO
+
+
VI
CL = 100 pF
RL
RL = 2 kΩ
Figure 1. Unity-Gain Amplifier
CL = 100 pF
Figure 2. Gain-of-10 Inverting Amplifier
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: TL072-EP TL074-EP
Submit Documentation Feedback
5
TL072-EP, TL074-EP
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
www.ti.com
TYPICAL CHARACTERISTICS
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices.
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
100
±15
VOM
VOM − Maximum Peak Output Voltage − V
IIIB−
IB Input Bias Current − nA
VCC± = ±15 V
10
1
0.1
0.01
−75
−50
−25
0
25
50
75
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREQUENCY
100
125
±12.5
±10
±7.5
ÁÁ
ÁÁ
ÁÁ
ÁÁ
±5
VCC± = ±15 V
VCC± = ±10 V
VCC± = ±5 V
±2.5
0
100
1k
TA − Free-Air Temperature − °C
10 k
100 k
f − Frequency − Hz
Figure 3.
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
±15
RL = 2 kΩ
TA = 25°C
See Figure 2
VCC± = ±15 V
±10
VCC± = ±10 V
±7.5
VCC± = ±5 V
±2.5
1k
±12.5
ÁÁ
ÁÁ
ÁÁ
ÁÁ
±5
0
100
VOM
VOM − Maximum Peak Output Voltage − V
VOM
VOM − Maximum Peak Output Voltage − V
±12.5
10 k
100 k
f − Frequency − Hz
Submit Documentation Feedback
10 M
1M
10 M
±10
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREQUENCY
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
VCC± = ±15 V
RL = 2 kΩ
See Figure 2
TA = 25°C
TA = −55°C
±7.5
±5
TA = 125°C
±2.5
0
10 k
40 k 100 k
400 k 1 M
f − Frequency − Hz
Figure 5.
6
1M
Figure 4.
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREQUENCY
±15
RL = 10 kΩ
TA = 25°C
See Figure 2
4M
10 M
Figure 6.
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: TL072-EP TL074-EP
TL072-EP, TL074-EP
www.ti.com
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
TYPICAL CHARACTERISTICS (continued)
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices.
MAXIMUM PEAK OUTPUT VOLTAGE
MAXIMUM PEAK OUTPUT VOLTAGE
vs
vs
FREE-AIR TEMPERATURE
LOAD RESISTANCE
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
±15
RL = 10 kΩ
±12.5
VOM − Maximum Peak Output Voltage − V
VOM
V
VOM
OM − Maximum Peak Output Voltage − V
±15
RL = 2 kΩ
±10
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
±7.5
±5
±2.5
VCC± = ±15 V
See Figure 2
0
−75
−50
−25
0
25
50
75
100
125
ÁÁ
ÁÁ
ÁÁ
ÁÁ
VCC± = ±15 V
TA = 25°C
See Figure 2
±12.5
±10
±7.5
±5
±2.5
0
0.1
0.2
TA − Free-Air Temperature − °C
0.4
7 10
LARGE-SIGNAL
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
±15
1000
RL = 10 kΩ
TA = 25°C
400
AAVD
VD − Large-Signal Differential
Voltage Amplification − V/mV
VOM
VOM − Maximum Peak Output Voltage − V
4
Figure 8.
MAXIMUM PEAK OUTPUT VOLTAGE
vs
SUPPLY VOLTAGE
ÁÁ
ÁÁ
ÁÁ
ÁÁ
2
RL − Load Resistance − kΩ
Figure 7.
±12.5
0.7 1
±10
±7.5
±5
±2.5
200
100
40
20
10
4
2
0
0
2
4
6
8
10
12
|VCC±| − Supply Voltage − V
14
16
1
−75
VCC± = ±15 V
VO = ±10 V
RL = 2 kΩ
−50
Figure 9.
−25
0
25
50
75
100
125
TA − Free-Air Temperature − °C
Figure 10.
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: TL072-EP TL074-EP
Submit Documentation Feedback
7
TL072-EP, TL074-EP
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
VCC± = ±5 V to ±15 V
RL = 2 kΩ
TA = 25°C
105
104
0°
Differential
Voltage
Amplification
103
45°
102
90°
Phase Shift
101
135°
1
1
10
100
1k
10 k 100 k
f − Frequency − Hz
1M
180°
10 M
1.01
1.1
Phase Shift
1
1
0.99
0.9
VCC± = ±15 V
RL = 2 kΩ
f = B1 for Phase Shift
0.8
0.7
−75
−50
2
ICC − Supply Current Per Amplifier − mA
I CC±
CMRR − Common-Mode Rejection Ratio − dB
SUPPLY CURRENT PER AMPLIFIER
vs
SUPPLY VOLTAGE
VCC± = ±15 V
RL = 10 kΩ
88
87
86
85
84
−50
−25
0
25
50
75
100
125
TA = 25°C
No Signal
No Load
1.8
1.6
1.4
1.2
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
1
0.8
0.6
0.4
0.2
0
0
2
4
TA − Free-Air Temperature − °C
Submit Documentation Feedback
6
8
10
12
14
16
|VCC±| − Supply Voltage − V
Figure 13.
8
0.97
125
Figure 12.
COMMON-MODE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
83
−75
0.98
−25
0
25
50
75
100
TA − Free-Air Temperature − °C
Figure 11.
89
1.02
Unity-Gain Bandwidth
1.2
Normalized Phase Shift
AAVD
VD − Large-Signal Differential
Voltage Amplification
106
Phase Shift
Normalized Unity-Gain Bandwidth
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices.
LARGE-SIGNAL
NORMALIZED UNITY-GAIN BANDWIDTH
DIFFERENTIAL VOLTAGE AMPLIFICATION
AND PHASE SHIFT
AND PHASE SHIFT
vs
vs
FREE-AIR TEMPERATURE
FREQUENCY
1.03
1.3
Figure 14.
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: TL072-EP TL074-EP
TL072-EP, TL074-EP
www.ti.com
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
TYPICAL CHARACTERISTICS (continued)
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices.
SUPPLY CURRENT PER AMPLIFIER
TOTAL POWER DISSIPATION
vs
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
250
VCC± = ±15 V
No Signal
No Load
1.8
1.6
1.4
1.2
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
1
0.8
0.6
0.4
200
175
150
125
100
0.2
0
−75
VCC± = ±15 V
No Signal
No Load
225
PD
PD − Total Power Dissipation − mW
ICC − Supply Current Per Amplifier − mA
I CC±
2
75
50
25
−50
−25
0
25
50
75
100
0
−75
125
−50
TA − Free-Air Temperature − °C
Figure 15.
Vn
V
nV/ Hz
n − Equivalent Input Noise Voltage − nV/Hz
Normalized Slew Rate − V/ µ s
1.15
VCC± = ±15 V
RL = 2 kΩ
CL = 100 pF
1.05
1
0.95
0.90
0.85
−75
0
25
50
75
100
125
Figure 16.
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
NORMALIZED SLEW RATE
vs
FREE-AIR TEMPERATURE
1.10
−25
TA − Free-Air Temperature − °C
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
50
VCC± = ±15 V
AVD = 10
RS = 20 Ω
TA = 25°C
40
30
20
10
0
−50
−25
0
25
50
75
100
125
10
40 100
TA − Free-Air Temperature − °C
Figure 17.
400 1 k
4 k 10 k
f − Frequency − Hz
40 k 100 k
Figure 18.
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: TL072-EP TL074-EP
Submit Documentation Feedback
9
TL072-EP, TL074-EP
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices.
TOTAL HARMONIC DISTORTION
VOLTAGE-FOLLOWER
vs
LARGE-SIGNAL PULSE RESPONSE
FREQUENCY
6
0.4
VCC± = ±15 V
AVD = 1
VI(RMS) = 6 V
TA = 25°C
VI and VO − Input and Output Voltages − V
THD − Total Harmonic Distortion − %
1
0.1
0.01
0.004
0.001
100
4
Output
2
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
0.04
VCC± = ±15 V
RL = 2 kΩ
CL = 100 pF
TA = 25°C
ÏÏÏ
ÏÏÏ
ÏÏÏ
0
−2
Input
−4
−6
400
1k
4 k 10 k
f − Frequency − Hz
0
40 k 100 k
0.5
1
1.5
t − Time − µs
Figure 19.
2
2.5
3
3.5
Figure 20.
OUTPUT VOLTAGE
vs
ELAPSED TIME
28
24
VVO
O − Output Voltage − mV
Overshoot
ÁÁ
ÁÁ
ÁÁ
ÁÁ
20
90%
16
12
8
4
VCC± = ±15 V
RL = 2 kΩ
TA = 25°C
10%
0
tr
−4
0
0.1
0.2 0.3 0.4 0.5
t − Elapsed Time − µs
0.6
0.7
Figure 21.
10
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: TL072-EP TL074-EP
TL072-EP, TL074-EP
www.ti.com
SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012
APPLICATION INFORMATION
1N4148
6 sin ωt
18 kΩ (see Note A)
−15 V
18 pF
18 pF
VCC+
VCC+
−
88.4 kΩ
TL072
−
+
6 cos ωt
TL072
+
88.4 kΩ
1 kΩ
VCC−
1 kΩ
18 pF
VCC−
15 V
18 kΩ (see Note A)
1N4148
88.4 kΩ
NOTE A: These resistor values may be adjusted for a symmetrical output.
Figure 22. 100-kHz Quadrature Oscillator
VCC+
−
1 MΩ
TL074
VCC+
+
VCC−
−
1 µF
TL074
VCC+
+
TL074
VCC−
100 kΩ
100 kΩ
Output B
+
VCC−
VCC+
VCC+
100 µF
100 kΩ
−
100 kΩ
−
Input
Output A
TL074
Output C
+
VCC−
Figure 23. Audio-Distribution Amplifier
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: TL072-EP TL074-EP
Submit Documentation Feedback
11
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TL072QDREP
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TL072Q
TL074MDEP
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-55 to 125
TL074M
TL074MDREP
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-55 to 125
TL074M
TL074QDREP
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TL074Q
V62/11621-01XE
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TL074Q
V62/11621-02XE
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-55 to 125
TL074M
V62/11621-02XE-T
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-55 to 125
TL074M
V62/12604-01XE
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TL072Q
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
