SLOS097C − MARCH 1991 − REVISED AUGUST 1996
D
D
D
D
D
D
D Low Input Offset Voltage . . . 3 mV Max
Wide Gain-Bandwidth Product . . . 4.5 MHz
High Slew Rate . . . 13 V/µs
Fast Settling Time . . . 1.1 µs to 0.1%
Wide-Range Single-Supply Operation
4 V to 44 V
Wide Input Common-Mode Range Includes
Ground (VCC −)
Low Total Harmonic Distortion . . . 0.02%
D
D
D
D
D
(A Suffix)
Large Output Voltage Swing
−14.7 V to 14 V (With ± 15-V Supplies)
Large Capacitance Drive Capability
10,000 pF
Excellent Phase Margin . . . 60°
Excellent Gain Margin . . . 12 dB
Output Short-Circuit Protection
D OR P PACKAGE
(SINGLE, TOP VIEW)
OFSET N1
IN −
IN +
VCC − /GND
1
8
2
7
3
6
4
5
D OR P PACKAGE
(DUAL, TOP VIEW)
NC
VCC +
OUT
OFSET N2
1OUT
1IN −
1IN +
VCC − /GND
DW PACKAGE
(QUAD, TOP VIEW)
1OUT
1IN −
1IN +
VCC +
2IN +
2IN −
2OUT
NC
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
1
8
2
7
3
6
4
5
VCC +
2OUT
2IN −
2IN +
N PACKAGE
(QUAD, TOP VIEW)
4OUT
4IN −
4IN +
VCC − /GND
3IN +
3IN −
3OUT
NC
1OUT
1IN −
1IN +
VCC +
2IN +
2IN −
2OUT
1
14
2
13
3
12
4
11
5
10
6
9
7
8
4OUT
4IN −
4IN +
VCC − /GND
3IN +
3IN −
3OUT
NC − No internal connection
AVAILABLE OPTIONS
PACKAGE
TA
COMPLEXITY
0°C
0
C
to
70°C
−40 C
−40°C
to
105°C
PLASTIC DIP
SMALL OUTLINE
STANDARD
GRADE
PRIME
GRADE
STANDARD
GRADE
PRIME
GRADE
Single
Dual
Quad
TL34071P
TL34072P
TL34074N
TL34071AP
TL34072AP
TL34074AN
TL34071D
TL34072D
TL34074DW
TL34071AD
TL34072AD
TL34074ADW
Single
Dual
Quad
TL33071P
TL33072P
TL33074N
TL33071AP
TL33072AP
TL33074AN
TL33071D
TL33072D
TL33074DW
TL33071AD
TL33072AD
TL33074ADW
−55 C
−55°C
to
125°C
Single
TL35071P
TL35071AP
TL35071D
TL35071AD
TL35072P
TL35072AP
TL35072D
TL35072AD
Dual
Quad
TL35074N
TL35074AN
TL35074DW
TL35074ADW
D and DW packages are available taped and reeled. Add R suffix to device type (e.g., TL34071ADR).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 1996, Texas Instruments Incorporated
!"#$%! & '("")% $& ! *(+,'$%! -$%).
"!-('%& '!!"# %! &*)''$%!& *)" %/) %)"#& ! )$&
&%"(#)%&
&%$-$"- 0$""$%1. "!-('%! *"!')&&2 -!)& !% )')&&$",1 ',(-)
%)&%2 ! $,, *$"$#)%)"&.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
1
SLOS097C − MARCH 1991 − REVISED AUGUST 1996
description
Quality, low cost, bipolar fabrication with innovative design concepts are employed for the TL33071/2/4,
TL34071/2/4, and TL35071/2/4 series of monolithic operational amplifiers. This series of operational amplifiers
offers 4.5 MHz of gain bandwidth product, 13 V/µs slew rate, and fast settling time without the use of JFET device
technology. Although this series can be operated from split supplies, it is particularly suited for single-supply
operation since the common-mode input voltage range includes ground potential (VCC −). With a Darlington
transistor input stage, this series exhibits high input resistance, low input offset voltage, and high gain. The
all-npn output stage, characterized by no dead-band crossover distortion and large output voltage swing,
provides high-capacitance drive capability, excellent phase and gain margins, low open-loop high-frequency
output impedance, and symmetrical source/sink ac frequency response.
The TL34071/2/4 devices are avaliable in standard or prime performance (A-suffix) grades and are specified
over the commercial (0°C to 70°C) temperature range. The TL33071/2/4 devices are available in standard or
prime performance (A-suffix) grades and are specified over industrial/vehicular (−40°C to 105°C) temperature
range. The TL35071/2/4 devices are avaliable in standard or prime performance (A-suffix) grades and are
specified over the military (− 55°C to 125°C) temperature range. These low-cost amplifiers are available in
single, dual, and quad configurations and are pin compatible with the MC33071/2/4, MC34071/2/4, and
MC35071/2/4 series of amplifiers. Packaging options include standard plastic DIP and SO packages.
symbol
Single
Dual and Quad
(per amplifier)
OFFSET N1
IN +
+
IN −
−
IN +
+
IN −
−
OUT
OFFSET N2
2
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
OUT
SLOS097C − MARCH 1991 − REVISED AUGUST 1996
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 V
Supply voltage, VCC − . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −22 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 44 V
Input voltage, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC ±
Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 1 mA
Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 80 mA
Total current into VCC + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 mA
Total current out of VCC − . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 mA
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: TL3307x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 105°C
TL3407x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
TL3507x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature 1.6 mm (1/16 inch) from case for 10 seconds: D, DW, N, or P package . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC −.
2. Differential voltages are at the noninverting input with respect to the inverting input. Excessive current flows if input is brought below
VCC − −0.3 V.
3. The output can be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
DISSIPATION RATING TABLE
PACKAGE
D
DW
N
P
TA ≤ 25
25°C
C
POWER RATING
725 mW
1025 mW
1150 mW
1000 mW
DERATING FACTOR
ABOVE TA = 25°C
TA = 70
70°C
C
POWER RATING
TA = 105
105°C
C
POWER RATING
TA = 125
125°C
C
POWER RATING
5.8 mW/
mW/°C
C
8.2 mW/
mW/°C
C
9.2 mW/
mW/°C
C
8.0 mW/°C
mW/ C
464 mW
656 mW
736 mW
640 mW
261 mW
369 mW
414 mW
360 mW
145 mW
205 mW
230 mW
200 mW
recommended operating conditions
TL3307x
Supply voltage, VCC ±
Common-mode input voltage, VIC
VCC = 5 V
VCC ± = ± 15 V
Operating free-air temperature, TA
•
TL3507x
MAX
MIN
MAX
MIN
MAX
±2
± 22
±2
± 22
±2
± 22
0
2.7
0
2.9
0
2.7
−15
12.7
−15
12.9
−15
12.7
−40
105
0
70
−55
125
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
TL3407x
MIN
UNIT
V
V
°C
3
SLOS097C − MARCH 1991 − REVISED AUGUST 1996
electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
TEST CONDITIONS
TA†
TL3x07xA
MIN TYP‡
MAX
VCC = 5 V
25°C
0.5
3
1.5
5
25°C
0.5
3
1.0
5
VIC = 0,
VO = 0,
RS = 50 Ω
VCC = ± 15 V
Full range
VCC = ± 15 V
Full range
10
VCC = ± 15 V
25°C
7
Full range
VCC = 5 V
Full range
5
Input bias current
VCC = ± 15 V
VICR
VOH
VOL
Common-mode input
voltage range
High-level output voltage
Low-level output voltage
−0.8
−0.7
Full range
−2
−0.8
−1.5
−0.7
−1.5
25°C
Full range
−15
to
12.8
−15
to
12.8
V
3.7
4
3.7
4
RL = 10 kΩ
25°C
13.6
14
13.6
14
RL = 2 kΩ
Full range
13.4
V
13.4
VCC + = 5 V, VCC − = 0,
RL = 2 kΩ
25°C
0.1
0.3
0.1
0.3
RL = 10 kΩ
25°C
−14.7
−14.3
−14.7
−14.3
RL = 2 kΩ
Full range
IOS
Short-circuit output current
CMRR
Common-mode
rejection ratio
VIC = VICRmin,
RS = 50 Ω
kSVR
Supply-voltage rejection
ratio (∆VCC ± /∆VIO)
VCC ± = ± 13.5 V
to ± 16.5 V,
RS = 100 Ω
VO = ± 10 V, RL = 2 kΩ
Source: VID = 1 V, VO = 0
Sink: VID = − 1 V, VO = 0
−13.5
Full range
25
100
No Load
100
V/mV
−10
−30
−10
−30
20
30
20
30
25°C
80
97
70
97
dB
25°C
80
97
70
97
dB
25°C
3.5
Full range
VCC + = 5 V, VCC − = 0,
VO = 0,
No Load
V
−13.5
25
20
25°C
VO = 0,
A
µA
−1.8
−15
to
13.2
50
nA
−2
−2.3
−1.8
25°C
mV
100
250
25°C
Large-signal differential
voltage amplification
Supply current
(per channel)
7
VCC + = 5 V, VCC − = 0,
RL = 2 kΩ
AVD
ICC
100
−15
to
13.2
RS = 50 Ω
UNIT
µV/°C
10
−2.3
25°C
MAX
7
250
25°C
IIB
TL3x07x
MIN TYP‡
25°C
4.5
3.5
4.7
3.4
4.4
mA
4.5
4.7
3.4
4.4
mA
Full range
4.6
4.6
† Full range is 0°C to 70°C for the TL3407x devices, and − 40°C to 105°C for the TL3307x devices, and − 55°C to 125°C for the TL3507x devices.
‡ All typical values are at TA = 25°C.
4
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SLOS097C − MARCH 1991 − REVISED AUGUST 1996
operating characteristics, VCC± = ±15 V, TA = 25°C
TL3x07xA
PARAMETER
TEST CONDITIONS
SR +
Positive slew rate
SR −
Negative slew rate
VI = − 10 V to 10 V,
RL = 2 kΩ
ts
Settling time
AVD = − 1, 10-V step
Vn
In
Equivalent input noise voltage
f = 1 kHz,
Equivalent input noise current
THD
GBW
AV = 1
AV = − 1
MIN
TYP
8
10
TL3x07x
MAX
MIN
TYP
8
10
MAX
UNIT
V/ s
V/µs
13
13
To 0.1%
1.1
1.1
To 0.01%
2.2
2.2
32
32
nV/√Hz
f = 1 kHz
0.22
0.22
pA/√Hz
Total harmonic distortion
VO = 2 V to 20 V, RL = 2 kΩ,
AVD = 10,
f = 10 kHz
0.02
0.02
%
Gain-bandwidth product
f =100 kHz
4.5
MHz
BW
Power bandwidth
RL = 2 kΩ,
AVD = 1,
VO(PP) = 20 V,
THD = 5.0%
200
200
kHz
φm
RL = 2 kΩ,
CL = 0
60°
60°
Phase margin
RL = 2 kΩ,
RL = 2 kΩ,
CL = 300 pF
40°
40°
12
12
RL = 2 kΩ,
CL = 300 pF
4
4
Gain margin
RS = 100 Ω
3.5
4.5
CL = 0
3.5
µss
dB
ri
Differential input resistance
150
MΩ
Input capacitance
VIC = 0
VIC = 0
150
Ci
2.5
2.5
pF
Channel separation
f = 10 kHZ
120
120
dB
Open-loop output impedance
f = 1 MHZ
30
30
Ω
zo
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
5
PACKAGE OPTION ADDENDUM
www.ti.com
14-Sep-2023
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TL35072P
LIFEBUY
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
TL35072P
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of