TL3414AID

    



    SLOS453A − DECEMBER 2004 − REVISED JANUARY 2005 D Single/Dual Power-Supply Operation D High Output Current . . . 70 mA, VCC+ = 5 V D Wide Operating Voltage . . . 3 V to 15 V D D (SOIC), P (PDIP), OR PW (TSSOP) PACKAGE (TOP VIEW) OUT1 IN1− IN1+ VCC − (Single Supply) Ideal for Headphone Drivers 1 8 2 7 3 6 4 5 VCC+ OUT2 IN2− IN2+ description/ordering information The TL3414A device is a dual operational amplifier that can be operated with single or dual power supplies. In addition to high gain and high output voltage swing, it is capable of driving a 70-mA load, making it ideally suited for simple, low-cost audio-amplifier applications, such as headphone amplifiers in DVD and CDRW applications. ORDERING INFORMATION PDIP (P) −40°C −40 C to 85 85°C C ORDERABLE PART NUMBER PACKAGE† TA SOIC (D) TSSOP (PW) Tube of 50 TL3414AIP Tube of 75 TL3414AID Reel of 2500 TL3414AIDR Tube of 150 TL3414AIPW Reel of 2000 TL3414AIPWR TOP-SIDE MARKING TL3414AIP Z3414A Z3414A † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. symbol (each amplifier) IN+ + IN − − OUT Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2005, Texas Instruments Incorporated  
 
   !   "#$ %!& %   "! "! '! ! 
!( ! %% )*& % "!+ %!  !!$* $%! !+  $$ "!!& POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 
    



    SLOS453A − DECEMBER 2004 − REVISED JANUARY 2005 simplified schematic V+ R Input− R Input+ V− Output absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC+ (single supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V Supply voltage, VCC − (single supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V Supply voltage, VCC+ (dual supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5 V Supply voltage, VCC − (dual supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −7.5 V Supply voltage, (VCC− to VCC+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V Input voltage, either input (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC− or VCC+ Input current (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 10 mA Duration of output short circuit (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited Package thermal impedance, θJA (see Notes 4 and 5): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . 149°C/W Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 125°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The magnitude of the input voltage must never exceed the magnitude of the supply voltage. 2. Excessive input current will flow if a differential input voltage in excess of approximately 0.6 V is applied between the inputs, unless some limiting resistance is used. 3. The output may be shorted to ground or either power supply. Temperature and/or supply voltages must be limited to ensure the maximum dissipation rating is not exceeded. 4. Maximum power dissipation is a function of TJ(max), qJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) − TA)/qJA. Operating at the absolute maximum TJ of 150°C can impact reliability. 5. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
    



    SLOS453A − DECEMBER 2004 − REVISED JANUARY 2005 recommended operating conditions MIN MAX UNIT VCC VCC + Supply voltage (single supply) 3 15 V Supply voltage (dual supply) 1.5 7.5 V VCC − VID Supply voltage (dual supply) −1.5 −7.5 V 15 V VI TA Input voltage −0.3 15 V Operating free-air temperature range −40 85 °C Differential input voltage DC electrical characteristics, VCC+ = 5 V, VCC− = 0 V, TA = 25°C (unless otherwise noted) PARAMETER VIO IIO Input offset voltage IIB AVD Input bias current VICR Common-mode input voltage range VOM TEST CONDITIONS MIN RS = 0 Ω Input offset current Large-signal differential voltage amplification Output voltage swing RL = 2 kΩ 77 RL > 2 kΩ, VCC+ = 5 V IO = 70 mA, VCC+ = 5 V CMRR Common-mode rejection ratio kSVR† Supply-voltage rejection ratio ICC Supply current (all amplifiers) RL = open circuit (full temperature range) † Measured with VCC± differentially and simultaneously varied from 5 V to 8.6 V TYP MAX 2 5 mV 15 100 nA 300 600 nA 100 UNIT dB VCC+ − 2 V 3.5 V V 3.2 70 79 dB 80 90 dB 3 4 6 mA AC electrical characteristics, VCC+ = 5 V, VCC− = 0 V, TA = 25°C (unless otherwise noted) PARAMETER SR Slew rate at unity gain GBW Gain bandwidth product Vn Equivalent input noise voltage TEST CONDITIONS TYP f = 1 kHz UNIT 0.83 V/µs 1.1 MHz 18 nV/√Hz DC electrical characteristics, VCC+ = 8.6 V, VCC− = 0 V, TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN RS = 0 Ω TYP MAX UNIT VIO IIO Input offset voltage 2 5 mV Input offset current 15 100 nA IIB Input bias current 300 600 nA AVD Large-signal differential voltage amplification VICR Common-mode input voltage range RL = 2 kΩ 88 RL > 2 kΩ, VCC+ = 8.6 V 105 VCC+ − 2 V 7 V VOM Output voltage swing CMRR kSVR† Common-mode rejection ratio 80 90 Supply-voltage rejection ratio 80 90 3 4 IO = 70 mA, VCC+ = 8.6 V ICC Supply current (all amplifiers) RL = open circuit (full temperature range) † Measured with VCC± differentially and simultaneously varied from 5 V to 8.6 V POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 dB V 6.7 dB dB 6 mA 3 
    



    SLOS453A − DECEMBER 2004 − REVISED JANUARY 2005 AC electrical characteristics, VCC+ = 8.6 V, VCC− = 0 V, TA = 25°C (unless otherwise noted) PARAMETER 4 SR Slew rate at unity gain GBW Gain bandwidth product Vn Equivalent input noise voltage TEST CONDITIONS f = 1 kHz POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TYP UNIT 1.3 V/µs 2 MHz 18 nV/√Hz PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) TL3414AID ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 Z3414A TL3414AIDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 Z3414A TL3414AIDRE4 ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 Z3414A TL3414AIPW ACTIVE TSSOP PW 8 150 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 Z3414A TL3414AIPWR ACTIVE TSSOP PW 8 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 Z3414A (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of