Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
TLC5940-EP 16-Channel LED Driver With Dot Correction and Grayscale PWM Control
1 Features
3 Description
•
•
•
The TLC5940-EP is a 16-channel, constant-current
sink LED driver. Each channel has an individually
adjustable 4096-step grayscale PWM brightness
control and a 64-step, constant-current sink (dot
correction). The dot correction adjusts the brightness
variations between LED channels and other LED
drivers. The dot correction data is stored in an
integrated EEPROM. Both grayscale control and dot
correction are accessible via a serial interface. A
single external resistor sets the maximum current
value of all 16 channels.
1
•
•
•
•
•
•
•
•
16 Channels
12-Bit (4096 Steps) Grayscale PWM Control
Dot Correction
– 6 Bit (64 Steps)
– Storable in Integrated EEPROM
Drive Capability (Constant-Current Sink) of
0 mA to 72 mA (–40°C to 125°C)
– 0 mA to 60 mA (VCC < 3.6 V, –40°C to 85°C)
– 0 mA to 120 mA (VCC > 3.6 V, –40°C to 85°C)
LED Power Supply Voltage up to 17 V
VCC = 3 V to 5.5 V
Serial Data Interface
Controlled In-Rush Current
30-MHz Data Transfer Rate
CMOS Level I/O
Error Information
– LOD: LED Open Detection
– TEF: Thermal Error Flag
The TLC5940-EP features two error information
circuits. The LED open detection (LOD) indicates a
broken or disconnected LED at an output terminal.
The thermal error flag (TEF) indicates an
overtemperature condition.
Device Information(1)
PART NUMBER
PACKAGE
TLC5940-EP
BODY SIZE (NOM)
HTSSOP (28)
9.70 mm × 4.40 mm
VQFN (32)
5.00 mm × 5.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
2 Applications
•
•
•
•
•
Monocolor, Multicolor, Full-Color LED Displays
LED Signboards
Display Backlighting
General, High-Current LED Drive
Supports Defense, Aerospace, and Medical
Applications:
– Controlled Baseline
– One Assembly/Test Site
– One Fabrication Site
– Available in Q-Temp (–40°C/125°C)
– Extended Product Life Cycle
– Extended Product-Change Notification
– Product Traceability
Simplified Schematic
VCC
SCLK
GND
SIN
XLAT
VPRG
IREF
Max. OUTn
Current
VREF =1.24 V
VPRG
1
DCPRG
CNT
1 0
GS Register
0
0
DCPRG
1
0
GSCLK
BLANK
DC Register
0
GS Counter
CNT
5
LED Open Detection
CNT
192
12
12−Bit Grayscale
PWM Control
GS Register
23
DCPRG
1
96
95
1 0
VPRG
96
6
Temperature
Error Flag
(TEF)
0
Constant Current
Driver
OUT1
Delay
x1
LED Open Detection
VPRG
CNT
Blank
1
6−Bit Dot
Correction
DC Register
11 0
6 DC EEPROM11
96
LED Open
Detection
(LOD)
OUT0
Delay
x0
VPRG
96
192
Constant Current
Driver
6−Bit Dot
Correction
0
0 DC EEPROM 5
Input
Shift
Register
Status 0
Information:
LOD,
TED,
DC DATA
191
12−Bit Grayscale
PWM Control
11
Input
Shift
Register
12−Bit Grayscale
PWM Control
GS Register
180
191
DCPRG
1
XERR
DC Register
90
95 0
191
90
SOUT
DC EEPROM
95
Constant Current
Driver
OUT15
Delay
x15
6−Bit Dot
Correction
LED Open Detection
VPRG
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
5
6.1
6.2
6.3
6.4
6.5
6.6
6.7
5
5
5
6
6
8
9
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Switching Characteristics ..........................................
Typical Characteristics ..............................................
7
Parameter Measurement Information ................ 11
8
Detailed Description ............................................ 14
7.1 Test Parameter Equations ...................................... 13
8.1 Overview ................................................................. 14
8.2 Functional Block Diagram ....................................... 14
8.3 Feature Description................................................. 14
8.4 Device Functional Modes........................................ 18
9
Application and Implementation ........................ 23
9.1 Application Information............................................ 23
9.2 Typical Application .................................................. 23
10 Power Supply Recommendations ..................... 25
11 Layout................................................................... 25
11.1 Layout Guidelines ................................................. 25
11.2 Layout Example .................................................... 25
11.3 Power Dissipation Calculation .............................. 26
12 Device and Documentation Support ................. 27
12.1
12.2
12.3
12.4
12.5
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
27
27
27
27
27
13 Mechanical, Packaging, and Orderable
Information ........................................................... 27
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (May 2010) to Revision E
Page
•
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section ................................................................................................. 1
•
Deleted Ordering Information table; see POA at the end of the data sheet........................................................................... 1
•
Changed thermal values for RHB (VQFN) package: 33.9 to 36.7 for RθJA, 30 to 18.9 for RθJC(top), 9.3 to 15.9 for RθJB,
0.619 to 0.6 for ψJT, 9.3 to 15.8 for ψJB, and 3.9 to 2.3 for RθJC(bot) ........................................................................................ 6
•
Changed thermal values for PWP (HTSSOP) package: 35.4 to 34.3 for RθJA, 24.94 to 36.8 for RθJC(top), 15.02 to 8.5
for RθJB, 1.297 to 0.3 for ψJT, 10.96 to 8.7 for ψJB, and 5.37 to 1.6 for RθJC(bot)....................................................................... 6
•
Deleted Dissipation Ratings table........................................................................................................................................... 6
Changes from Revision B (September 2007) to Revision C
•
2
Page
Changed from ms to ns .......................................................................................................................................................... 6
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
5 Pin Configuration and Functions
PWP Package
28-Pin HTSSOP
Top View
17 OUT11
18 OUT12
19 OUT13
20 OUT14
21 OUT15
22 XERR
23 SOUT
16 OUT10
DCPRG 25
IREF 26
15 OUT9
VCC 27
14 OUT8
THERMAL
PAD
NC 28
NC 29
13 NC
12 NC
GND 30
11 OUT7
OUT4 8
OUT3 7
OUT2 6
OUT1 5
9 OUT5
OUT0 4
10 OUT6
32
SIN 2
31
XLAT
VPRG 3
BLANK
SCLK 1
Thermal
PAD
VCC
IREF
DCPRG
GSCLK
SOUT
XERR
OUT15
OUT14
OUT13
OUT12
OUT11
OUT10
OUT9
OUT8
28
27
26
25
24
23
22
21
20
19
18
17
16
15
24 GSCLK
1
2
3
4
5
6
7
8
9
10
11
12
13
14
GND
BLANK
XLAT
SCLK
SIN
VPRG
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
RHB Package
32-Pin VQFN
Top View
Pin Functions
PIN
NAME
HTSSOP
VQFN
BLANK
2
31
I/O
DESCRIPTION
I
Blank all outputs. When BLANK = H, all OUTn outputs are forced OFF. GS counter is
also reset. When BLANK = L, OUTn are controlled by grayscale PWM control.
DCPRG
26
25
I
Switch DC data input. When DCPRG = L, DC is connected to EEPROM. When
DCPRG = H, DC is connected to the DC register.
DCPRG also controls EEPROM writing, when VPRG = V(PRG). EEPROM data = 3Fh
(default)
GND
1
30
G
Ground
GSCLK
25
24
I
Reference clock for grayscale PWM control
IREF
27
26
I
Reference current terminal
NC
—
12, 13, 28,
29
—
No connection
OUT0
7
4
O
Constant current output
OUT1
8
5
O
Constant current output
OUT2
9
6
O
Constant current output
OUT3
10
7
O
Constant current output
OUT4
11
8
O
Constant current output
OUT5
12
9
O
Constant current output
OUT6
13
10
O
Constant current output
OUT7
14
11
O
Constant current output
OUT8
15
14
O
Constant current output
OUT9
16
15
O
Constant current output
OUT10
17
16
O
Constant current output
OUT11
18
17
O
Constant current output
OUT12
19
18
O
Constant current output
OUT13
20
19
O
Constant current output
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
3
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
Pin Functions (continued)
PIN
I/O
DESCRIPTION
NAME
HTSSOP
VQFN
OUT14
21
20
O
Constant current output
OUT15
22
21
O
Constant current output
SCLK
4
1
I
Serial data shift clock
SIN
5
2
I
Serial data input
SOUT
24
23
O
Serial data output
VCC
28
27
I
Power supply voltage
VPRG
6
3
I
Multifunction input pin. When VPRG = GND, the device is in GS mode. When VPRG =
VCC, the device is in DC mode. When VPRG = V(VPRG), DC register data can
programmed into DC EEPROM with DCPRG=HIGH. EEPROM data = 3Fh (default)
XERR
23
22
O
Error output. XERR is an open-drain terminal. XERR goes L when LOD or TEF is
detected.
XLAT
3
32
I
Level triggered latch signal. When XLAT = high, the TLC5940-EP writes data from the
input shift register to either GS register (VPRG = low) or DC register (VPRG = high).
When XLAT = low, the data in GS or DC register is held constant.
4
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
Input voltage (3)
Output voltage
(2)
MIN
MAX
UNIT
VCC
–0.3
6
V
V(BLANK), V(DCPRG), V(SCLK), V(XLAT), V(SIN), V(GSCLK), V(IREF)
–0.3
VCC + 0.3
V
V(SOUT), V(XERR)
–0.3
VCC + 0.3
V
V(OUT0) to V(OUT15)
–0.3
18
V
130
mA
24
V
Output current (dc)
IO
EEPROM program
V(VPRG)
–0.3
EEPROM write cycles
25
Package thermal impedance
See Thermal Information
Operating ambient temperature, TA
–40
125
°C
Storage temperature, Tstg
–55
150
°C
(1)
(2)
(3)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute maximum rated conditions for extended periods may affect device reliability.
Long-term high-temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of
overall device life. See www.ti.com/ep_quality for additional information on enhanced plastic packaging.
All voltage values are with respect to network ground terminal.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic
discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (1)
±2000
Charged device model (CDM), per JEDEC specification JESD22-C101, all
pins (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
MIN
NOM
MAX
UNIT
DC CHARACTERISTICS
VCC
Supply Voltage
3
5.5
V
VO
Voltage applied to output (OUT0–OUT15)
VIH
17
V
High-level input voltage
0.8 VCC
VCC
V
VIL
Low-level input voltage
GND
0.2 VCC
V
IOH
High-level output current
VCC = 5 V at SOUT
–1
mA
IOL
Low-level output current
VCC = 5 V at SOUT
1
mA
–40°C to 125°C
IOLC
Constant output current
OUT0 to OUT15
V(VPRG)
EEPROM program voltage
TA
Operating free-air temperature
AC CHARACTERISTICS
72
–40°C to 85°C, VCC < 3.6 V
60
–40°C to 85°C, VCC > 3.6 V
120
20
–40
22
mA
23
V
125
°C
(1)
f(SCLK)
Data shift clock frequency SCLK
30
MHz
f(GSCLK)
Grayscale clock
frequency
GSCLK
30
MHz
twh0/twl0
SCLK pulse duration
SCLK = H/L (see Figure 12)
16
ns
twh1/twl1
GSCLK pulse duration
GSCLK = H/L (see Figure 12)
16
ns
twh2
XLAT pulse duration
XLAT = H (see Figure 12)
20
ns
(1)
VCC = 3 V to 5.5 V, TA = –40°C to 125°C (unless otherwise noted)
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
5
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
Recommended Operating Conditions (continued)
MIN
twh3
BLANK pulse duration
BLANK = H (see Figure 12)
NOM
MAX
UNIT
20
ns
5
ns
tsu0
SIN to SCLK ↑ (2) (see Figure 12)
tsu1
SCLK ↓ to XLAT ↑ (see Figure 12)
10
ns
tsu2
VPRG ↑ ↓ to SCLK ↑ (see Figure 12)
10
ns
VPRG ↑ ↓XLAT ↑ (see Figure 12)
10
ns
tsu4
BLANK ↓ to GSCLK ↑ (see Figure 12)
10
ns
tsu5
XLAT ↑ to GSCLK ↑ (see Figure 12)
30
ns
tsu6
VPRG ↑ to DCPRG ↑ (see Figure 17)
1
ms
th0
SCLK ↑ to SIN (see Figure 12)
3
ns
th1
XLAT ↓ to SCLK ↑ (see Figure 12)
10
ns
th2
SCLK ↑ to VPRG ↑ ↓ (see Figure 12)
10
ns
XLAT ↓ to VPRG ↑ ↓ (see Figure 12)
10
ns
th4
GSCLK ↑ to BLANK ↑ (see Figure 12)
10
ns
th5
DCPRG ↓ to VPRG ↓ (see Figure 12)
1
ms
tprog
Programming time for EEPROM (see Figure 17)
20
ms
tsu3
Setup time
Hold time
th3
(2)
↑ and ↓ indicates a rising edge, and a falling edge respectively.
6.4 Thermal Information
TLC5940-EP
THERMAL METRIC (1)
RHB (VQFN)
PWP (HTSSOP)
UNIT
32 PINS
28 PINS
RθJA
Junction-to-ambient thermal resistance
36.7
34.3
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
18.9
36.8
°C/W
RθJB
Junction-to-board thermal resistance
15.9
8.5
°C/W
ψJT
Junction-to-top characterization parameter
0.6
0.3
°C/W
ψJB
Junction-to-board characterization parameter
15.8
8.7
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
2.3
1.6
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Electrical Characteristics
VCC = 3 V to 5.5 V, TA = –40°C to 125°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOH
High-level output voltage
IOH = –1 mA, SOUT
VOL
Low-level output voltage
IOL = 1 mA, SOUT
II
Input current
MIN
TYP
VCC –0.5
6
Supply current
VI = VCC or GND; BLANK, DCPRG, GSCLK, SCLK,
SIN, XLAT
–1
1
VI = GND; VPRG
–2
2
V
µA
50
VI = 21 V; VPRG; DCPRG = VCC
4
10
No data transfer, all output OFF,
VO = 1 V, R(IREF) = 10 kΩ
0.9
6
No data transfer, all output OFF,
VO = 1 V, R(IREF) = 1.3 kΩ
5.2
12
Data transfer 30 MHz, all output ON,
VO = 1 V, R(IREF) = 1.3 kΩ
16
Data transfer 30 MHz, all output ON,
VO = 1 V, R(IREF) = 640 Ω
30
Submit Documentation Feedback
UNIT
V
0.5
VI = VCC; VPRG
ICC
MAX
mA
mA
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
Electrical Characteristics (continued)
VCC = 3 V to 5.5 V, TA = –40°C to 125°C (unless otherwise noted)
PARAMETER
IO(LC)
Constant sink current (see
Figure 10)
Ilkg
Leakage output current
ΔIO(LC0)
Constant sink current error (see
Figure 10)
TEST CONDITIONS
MIN
TYP
MAX
All output ON, VO = 1 V, R(IREF) = 640 Ω, 25°C
54
61
69
All output ON, VO = 1 V, R(IREF) = 640 Ω, Full
temperature
42
61
72
All output OFF, VO = 15 V, R(IREF) = 640 Ω,
OUT0 to OUT15
All output ON, VO = 1 V, R(IREF) = 640 Ω,
OUT0 to OUT15, 25°C
±4%
All output ON, VO = 1 V, R(IREF) = 640 Ω,
OUT0 to OUT15 (1), Full temperature
±12%
All output ON, VO = 1 V, R(IREF) = 1300 Ω,
OUT0 to OUT15, 25°C
±4%
All output ON, VO = 1 V, R(IREF) = 1300 Ω,
OUT0 to OUT15 (1), Full temperature
±8%
ΔIO(LC1)
Constant sink current error (see
Figure 10)
Device to device, Averaged current from OUT0 to
OUT15, R(IREF) = 1920 Ω (20 mA) (2)
ΔIO(LC2)
Constant sink current error (see
Figure 10)
Device to device, Averaged current from OUT0 to
OUT15, R(IREF) = 480 Ω (80 mA) (2)
ΔIO(LC3) Line regulation (see Figure 10)
ΔIO(LC4) Load regulation (see Figure 10)
T(TEF)
Thermal error flag threshold
V(LED)
LED open detection threshold
V(IREF)
Reference voltage
output
(1)
(2)
(3)
(4)
(5)
±1
0.4%
2%
All output ON, VO = 1 V, R(IREF) = 640 Ω
OUT0 to OUT15 (3), Full temperature
±11
%/V
All output ON, VO = 1 V, R(IREF) = 1300 Ω ,
OUT0 to OUT15 (3), 25°C
±4
All output ON, VO = 1 V, R(IREF) = 1300 Ω,
OUT0 to OUT15 (3), Full temperature
±4
All output ON, VO = 1 V to 3 V, R(IREF) = 640 Ω,
OUT0 to OUT15 (4), 25°C
±6
All output ON, VO = 1 V to 3 V, R(IREF) = 640 Ω,
OUT0 to OUT15 (4), Full temperature
±20
All output ON, VO = 1 V to 3 V, R(IREF) = 1300 Ω,
OUT0 to OUT15 (4), 25°C
±6
All output ON, VO = 1 V to 3 V, R(IREF) = 1300 Ω,
OUT0 to OUT15 (4), Full temperature
±6
R(IREF) = 640 Ω
µA
–2.7%
±4
Junction temperature
mA
–2%
All output ON, VO = 1 V, R(IREF) = 640 Ω
OUT0 to OUT15 (3), 25°C
(5)
UNIT
%/V
150
1.2
170
°C
0.3
0.4
V
1.24
1.28
V
The deviation of each output from the average of OUT0-15 constant current. It is calculated by Equation 1.
The deviation of average of OUT1-15 constant current from the ideal constant-current value. It is calculated by Equation 2. The ideal
current is calculated by Equation 3.
The line regulation is calculated by Equation 4.
The load regulation is calculated by Equation 5.
Not tested. Specified by design
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
7
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
6.6 Switching Characteristics
VCC = 3 V to 5.5 V, TA = –40°C to 125°C (unless otherwise noted)
PARAMETER
tr0
tr1
tf0
tf1
Rise time
Fall time
TEST CONDITIONS
MIN
TYP
SOUT
MAX
16
OUTn, VCC = 5 V, TA = 60°C, DCn = 3 Fh
10
SOUT
30
16
OUTn, VCC = 5 V, TA = 60°C, DCn = 3 Fh
10
30
UNIT
ns
ns
tpd0
SCLK to SOUT (see Figure 12)
30
ns
tpd1
BLANK to OUT0
60
ns
tpd2
OUTn to XERR (see Figure 12 )
1000
ns
tpd3
Propagation delay time
GSCLK to OUT0 (see Figure 12 )
60
ns
tpd4
XLAT to IOUT (dot correction) (see Figure 12 )
60
ns
tpd5
DCPRG to OUT0 (see Figure 12)
30
ns
20
30
ns
–50
–90
ns
td
Output delay time
OUTn to OUT(n+1) (see Figure 12 )
ton-err
Output on-time error
touton– Tgsclk (see Figure 12), GSn = 01 h, GSCLK = 11 MHz
8
Submit Documentation Feedback
10
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
6.7 Typical Characteristics
4k
10 k
TLC5940PWP
PowerPAD Soldered
1.92 kΩ
1k
TLC5940RHB
Power Dissipation Rate - mW
Reference Resistor, R(IREF) - W
7.68 kΩ
0.96 kΩ
0.64 kΩ
0.48 kΩ
0.38 kΩ
3k
2k
TLC5940PWP
PowerPAD Unsoldered
1k
0.32 kΩ
100
0
20
40
80
60
100
0
-40
120
-20
80
60
100
65
TA = 25°C,
VCC = 5 V
IO = 120 mA
IO = 60 mA,
VCC = 5 V
64
TA = 85°C
63
IO = 100 mA
IO - Output Current - mA
IO - Output Current - mA
40
Figure 2. Power Dissipation Rate vs Free-Air Temperature
140
100
IO = 80 mA
80
IO = 60 mA
60
IO = 40 mA
40
62
61
60
TA = 25°C
TA = -40°C
59
58
IO = 20 mA
57
IO = 5 mA
56
20
55
0
0
0.5
1
1.5
2
VO - Output Voltage - V
2.5
0
3
1
1.5
2
2.5
3
Figure 4. Output Current vs Output Voltage
8
8
TA = 25°C,
VCC = 5 V
IO = 60 mA
6
Δ IOLC - Constant Output Current - %
6
4
VCC = 3.3 V
2
0
-2
VCC = 5 V
-4
-6
-8
-40
0.5
VO - Output Voltage - V
Figure 3. Output Current vs Output Voltage
Δ IOLC - Constant Output Current - %
20
TA − Free-Air Temperature − C
Figure 1. Reference Resistor vs Output Current
120
0
o
IO − Output Current − mA
-20
0
20
40
60
80
TA - Ambient Temperature - °C
100
Figure 5. Constant Output Current, ΔIOLC vs Ambient
Temperature
4
2
0
-2
-4
-6
-8
0
20
40
60
IO - Output Current - mA
80
Figure 6. Constant Output Current, ΔIOLC vs Output Current
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
9
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
Typical Characteristics (continued)
140
IO = 60 mA,
VCC = 5 V
IO = 120 mA
60
100
IO = 80 mA
80
IO = 60 mA
60
40
IO = 30 mA
IO - Output Current - mA
IO - Output Current - mA
120
70
TA = 25°C,
VCC = 5 V
TA = 25°C
TA = 85°C
50
TA = -40°C
40
30
20
10
20
IO = 5 mA
0
0
0
10
20
30
40
50
Dot Correction Data - dec
60
Figure 7. Output Current vs DOT Correction Linearity (ABS
Value)
10
0
70
10
20
30
40
50
Dot Correction Data - dec
60
70
Figure 8. Output Current vs DOT Correction Linearity (ABS
Value)
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
7 Parameter Measurement Information
Resistor values are equivalent resistances, and they are not tested.
INPUT EQUIVALENT CIRCUIT
(BLANK, XLAT, SCLK, SIN, GSCLK, DCPRG)
OUTPUT EQUIVALENT CIRCUIT (SOUT)
VCC
VCC
23 W
400 W
INPUT
SOUT
23 W
GND
GND
INPUT EQUIVALENT CIRCUIT (IREF)
V(IREF)
VCC
Amp
_
400 W
+
INPUT
OUTPUT EQUIVALENT CIRCUIT (XERR)
23 W
XERR
100 W
GND
GND
INPUT EQUIVALENT CIRCUIT (VCC)
OUTPUT EQUIVALENT CIRCUIT (OUT)
INPUT
OUT
GND
INPUT EQUIVALENT CIRCUIT (VPRG)
INPUT
GND
GND
Figure 9. Input and Output Equivalent Circuits
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
11
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
Parameter Measurement Information (continued)
tr0, tf0, tpd0
tr1, tf1, tpd1, tpd2, tpd3, tpd4, tpd5, td
VO = 4V
Testpoint
SOUT
RL = 51W
CL = 15pF
Testpoint
OUTn
CL = 15pF
IO(LC), DIO(LC0), DIO(LC1), DIO(LC2), DIO(LC3)
DIO(LC4)
OUTn
OUTn
VO = 1V
VO = 1V to 3V
V(IREF)
tpd3
VCC
Testpoint
IREF
R (IREG) = 640W
470kΩ
XERR
Figure 10. Parameter Measurement Circuits
1.00E+04
Notes:
1. See datasheet for absolute maximum and minimum recommended operating conditions.
2. Silicon operating life design goal is 10 years at 105°C junction temperature (does not include
package interconnect life).
3. Enhanced plastic product disclaimer applies.
Estimated Life (Years)
1.00E+03
Wirebond Voiding
Fail Mode (PWP)
1.00E+02
Wirebond Voiding
Fail Mode (RHB)
1.00E+01
1.00E+00
100
110
120
130
140
150
160
Continuous TJ (°C)
Figure 11. TLC5940-EP Mold Compound Operating Life
12
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
7.1 Test Parameter Equations
D(%) =
D(%) =
I OUTn - I OUTavg _ 0 -15
IOUTavg _ 0 -15
IOUTavg - I OUT (IDEAL )
I OUT (IDEAL )
´ 100
(1)
´ 100
(2)
æ 1.24 V ö
÷÷
IOUT (IDEAL ) = 31.5 ´ çç
è R IREF ø
(3)
(I
at VCC = 5.5 V ) - (I OUTn at VCC = 3.0 V ) 100
D(% / V ) = OUTn
´
(I OUTn at VCC = 3.0 V )
2.5
(4)
(I
at VOUTn = 3.0 V ) - (IOUTn at VOUTn = 1.0 V ) 100
D(% / V ) = OUTn
´
(IOUTn at VOUTn = 1.0 V )
2 .0
(5)
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
13
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
8 Detailed Description
8.1 Overview
The TLC5940-EP is a 16-channel constant current sink driver. Each channel has an individually-adjustable,
4096-step, pulse width modulation (PWM), grayscale (GS) brightness control, and a 64-step dot correction
brightness control. GS data and DC data are input via a serial interface port. The dot correction data is stored in
an integrated EEPROM. The TLC5940-EP has a 120-mA current capability. The maximum current value of all
channels is determined by an external resistor. The TLC5940-EP has a LED open detection (LOD) function that
indicates a broken or disconnected LED at an output terminal and a thermal error flag (TEF) indicates an
overtemperature condition.
8.2 Functional Block Diagram
VCC
SCLK
GND
SIN
XLAT
VPRG
IREF
Max. OUTn
Current
VREF =1.24 V
VPRG
1
DCPRG
CNT
1 0
GS Register
0
0
DCPRG
1
0
GSCLK
BLANK
DC Register
0
GS Counter
CNT
5
LED Open Detection
CNT
192
12
12−Bit Grayscale
PWM Control
GS Register
23
DCPRG
1
96
95
1 0
VPRG
96
6 DC EEPROM11
Temperature
Error Flag
(TEF)
0
Constant Current
Driver
OUT1
Delay
x1
LED Open Detection
VPRG
CNT
Blank
1
6−Bit Dot
Correction
DC Register
11 0
6
96
LED Open
Detection
(LOD)
OUT0
Delay
x0
VPRG
96
192
Constant Current
Driver
6−Bit Dot
Correction
0
0 DC EEPROM 5
Input
Shift
Register
Status 0
Information:
LOD,
TED,
DC DATA
191
12−Bit Grayscale
PWM Control
11
Input
Shift
Register
12−Bit Grayscale
PWM Control
GS Register
180
191
DCPRG
1
XERR
90
191
90
SOUT
DC Register
95 0
DC EEPROM
95
Constant Current
Driver
OUT15
Delay
x15
6−Bit Dot
Correction
LED Open Detection
VPRG
8.3 Feature Description
8.3.1 Serial Interface
The TLC5940-EP has a flexible serial interface, which can be connected to microcontrollers or digital signal
processors in various ways. Only 3 pins are needed to input data into the device. The rising edge of SCLK signal
shifts the data from the SIN pin to the internal register. After all data is clocked in, a high-level pulse of XLAT
signal latches the serial data to the internal registers. The internal registers are level-triggered latches of XLAT
signal. All data are clocked in with the MSB first. The length of serial data is 96 bit or 192 bit, depending on the
programming mode. Grayscale data and dot correction data can be entered during a grayscale cycle. Although
new grayscale data can be clocked in during a grayscale cycle, the XLAT signal should only latch the grayscale
data at the end of the grayscale cycle. Latching in new grayscale data immediately overwrites the existing
grayscale data. Figure 12 shows the timing chart. More than two TLC5940-EPs can be connected in series by
connecting an SOUT pin from one device to the SIN pin of the next device. An example of cascading two
TLC5940-EPs is shown in Figure 13 and the timing chart is shown in Figure 14. The SOUT pin can also be
connected to the controller to receive status information from TLC5940-EP as shown in Figure 23.
14
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
Feature Description (continued)
VPRG
DC Data Input Mode
GS Data Input Mode
th3
tsu3
twh2
XLAT
1st GS Data Input Cycle
DC
MSB
SIN
GS2
MSB
GS2
LSB
th1
tsu1
1
96
1
GS1
LSB
tsu2
th2
SCLK
2nd GS Data Input Cycle
GS1
MSB
DC
LSB
GS3
MSB
tsu0
twh0
192
193
th0
193
192
1
tpd0
twl0
-
SOUT
DC
MSB
-
GS1
MSB
-
1
SID1 SID1
MSB MSB-1
SID2 SID2
MSB MSB-1
SID1 GS2
LSB MSB
twh3
BLANK
1st GS Data Output Cycle
1
tpd4
1
4096
tpd3
tpd1
Tgsclk
tpd3
OUT0
(current)
tpd3 + td
td
tpd1 + td
twh1
tsu4
th4
tsu5
GSCLK
2nd GS Data Output Cycle
twl1
touton
OUT1
(current)
15 x td
tpd1 + 15 x td
OUT15
(current)
tpd2
XERR
Figure 12. Serial Data Input Timing Chart
SIN(a)
SIN
SOUT
TLC5940 (a)
SIN
SOUT
SOUT(b )
TLC5940 (b)
SCLK, XLAT,
BLANK,
GSCLK,
DCPRG,
VPRG
Figure 13. Cascading Two TLC5940-EP Devices
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
15
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
Feature Description (continued)
VPRG
XLAT
SIN(a )
SCLK
DCb
MSB
GSb1
MSB
DCa
LSB
1
192
1
GSa1
LSB
384
-
385
GSa2
LSB
GSb3
MSB
385
384
1
1
192X2
96X2
SOUT(b )
GSb2
MSB
DCb
MSB
-
GSb1
MSB
-
SIDb1 SIDb1
MSB MSB-1
SIDa1
LSB
SIDb2 SIDb2
MSB MSB-1
GSb2
MSB
BLANK
1
GSCLK
1
4096
OUT0
(current)
OUT1
(current)
OUT15
(current)
XERR
Figure 14. Timing Chart for Two Cascaded TLC5940-EP Devices
8.3.2 Error Information Output
The open-drain output XERR is used to report both of the TLC5940-EP error flags, TEF and LOD. During normal
operating conditions, the internal transistor connected to the XERR pin is turned off. The voltage on XERR is
pulled up to VCC through an external pullup resistor. If TEF or LOD is detected, the internal transistor is turned
on, and XERR is pulled to GND. Since XERR is an open-drain output, multiple ICs can be OR'ed together and
pulled up to VCC with a single pullup resistor. This reduces the number of signals needed to report a system error
(see Figure 23).
To differentiate LOD and TEF signal from XERR pin, LOD can be masked out with BLANK = HIGH.
Table 1. XERR Truth Table
ERROR CONDITION
OUTn VOLTAGE
TJ < T(TEF)
TJ > T(TEF)
TJ < T(TEF)
TJ > T(TEF)
16
ERROR INFORMATION
TEMPERATURE
TEF
LOD
Don't Care
L
X
Don't Care
H
X
OUTn > V(LED)
L
L
OUTn < V(LED)
L
H
OUTn > V(LED)
H
L
OUTn < V(LED)
H
H
Submit Documentation Feedback
SIGNALS
BLANK
H
XERR
H
L
H
L
L
L
L
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
8.3.3 TEF: Thermal Error Flag
The TLC5940-EP provides a temperature error flag (TEF) circuit to indicate an overtemperature condition of the
IC. If the junction temperature exceeds the threshold temperature (160°C typical), TEF becomes H and XERR
pin goes to low level. When the junction temperature becomes lower than the threshold temperature, TEF
becomes L and XERR pin becomes high impedance. TEF status can also be read out from the TLC5940-EP
status register.
8.3.4 LOD: LED Open Detection
The TLC5940-EP has an LED-open detector that detects broken or disconnected LEDs. The LED open detector
pulls the XERR pin to GND when an open LED is detected. XERR and the corresponding error bit in the Status
Information Data is only active under the following open-LED conditions.
1. OUTn is on and the time tpd2 (1 µs typical) has passed.
2. The voltage of OUTn is < 0.3 V (typical)
The LOD status of each output can be also read out from the SOUT pin. See Status Information Output for
details. The LOD error bits are latched into the Status Information Data when XLAT returns to a low after a high.
Therefore, the XLAT pin must be pulsed high then low while XERR is active in order to latch the LOD error into
the Status Information Data for subsequent reading via the serial shift register.
8.3.5 Delay Between Outputs
The TLC5940-EP has graduated delay circuits between outputs. These circuits can be found in the constant
current driver block of the device (see Functional Block Diagram). The fixed-delay time is 20 ns (typical), OUT0
has no delay, OUT1 has 20-ns delay, and OUT2 has 40-ns delay, and so forth. The maximum delay is 300 ns
from OUT0 to OUT15. The delay works during switch on and switch off of each output channel. These delays
prevent large inrush currents which reduces the bypass capacitors when the outputs turn on.
8.3.6 Output Enable
All OUTn channels of the TLC5940-EP can be switched off with one signal. When BLANK is set high, all OUTn
channels are disabled, regardless of logic operations of the device. The grayscale counter is also reset. When
BLANK is set low, all OUTn channels work under normal conditions. If BLANK goes low and then back high
again in less than 300 ns, all outputs programmed to turn on still turn on for either the programmed number of
grayscale clocks, or the length of time that the BLANK signal was low, which ever is lower. For example, if all
outputs are programmed to turn on for 1 ms, but the BLANK signal is only low for 200 ns, all outputs still turn on
for 200 ns, even though some outputs are turning on after the BLANK signal has already gone high.
Table 2. BLANK Signal Truth Table
BLANK
OUT0 - OUT15
LOW
Normal condition
HIGH
Disabled
8.3.7 Setting Maximum Channel Current
The maximum output current per channel is programmed by a single resistor, R(IREF), which is placed between
IREF pin and GND pin. The voltage on IREF is set by an internal band gap V(IREF) with a typical value of
1.24 V. The maximum channel current is equivalent to the current flowing through R(IREF) multiplied by a factor of
31.5. The maximum output current per channel can be calculated by Equation 6:
V
(IREF)
I max =
× 31.5
R
(IREF)
where
•
•
V(IREF) = 1.24 V.
R(IREF) = User-selected external resistor.
(6)
Imax must be set between 5 mA and 120 mA. The output current may be unstable if Imax is set lower than 5 mA.
Output currents lower than 5 mA can be achieved by setting Imax to 5 mA or higher and then using dot correction.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
17
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
Figure 1 shows the maximum output current IO versus R(IREF). R(IREF) is the value of the resistor between IREF
terminal to GND, and IO is the constant output current of OUT0 to OUT15. A variable power supply may be
connected to the IREF pin through a resistor to change the maximum output current per channel. The maximum
output current per channel is 31.5 times the current flowing out of the IREF pin.
8.4 Device Functional Modes
8.4.1 Operating Modes
The TLC5940-EP has operating modes depending on the signals DCPRG and VPRG. Table 3 shows the
available operating modes. The TPS5940 GS operating mode (see Figure 12) and shift register values are not
defined after power up. One solution to solve this is to set dot correction data after TLS5940 power up and
switch back to GS PWM mode. The other solution is to overflow the input shift register with 193 bits of dummy
data and latch it while TLS540 is in GS PWM mode. The values in the input shift register, DC register and GS
register are unknown just after power on. The DC and GS register values should be properly stored through the
serial interface before starting the operation.
Table 3. TLC5940-EP Operating Modes Truth Table
SIGNAL
INPUT SHIFT REGISTER
MODE
GND
192 bit
Grayscale PWM Mode
VCC
96 bit
Dot Correction Data Input Mode
V(VPRG)
X
EEPROM Programming Mode
DCPRG
VPRG
L
H
L
H
DC VALUE
EEPROM
DC Register
EEPROM
DC Register
L
EEPROM
H
Write DC register value to EEPROM. (Default
data: 3Fh)
8.4.2 Setting Dot Correction
The TLC5940-EP has the capability to fine adjust the output current of each channel OUT0 to OUT15
independently. This is also called dot correction. This feature is used to adjust the brightness deviations of LEDs
connected to the output channels OUT0 to OUT15. Each of the 16 channels can be programmed with a 6-bit
word. The channel output can be adjusted in 64 steps from 0% to 100% of the maximum output current Imax. Dot
correction for all channels must be entered at the same time. Equation 7 determines the output current for each
output n:
DCn
I
I
OUTn = max × 63
where
•
•
•
Imax = the maximum programmable output current for each output.
DCn = the programmed dot correction value for output n (DCn = 0 to 63).
n = 0 to 15
(7)
Figure 15 shows the dot correction data packet format which consists of 6 bits × 16 channel, total 96 bits. The
format is Big-Endian format. This means that the MSB is transmitted first, followed by the MSB-1, and so forth.
The DC 15.5 in Figure 15 stands for the 5th most significant bit for output 15.
MSB
LSB
95
90
DC 15.5
89
6
DC 15.0 DC 14.5
DC OUT15
DC 1.0
5
0
DC 0.5
DC 0.0
DC OUT0
DC OUT14 − DC OUT2
Figure 15. Dot Correction Data Packet Format
18
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
When VPRG is set to VCC, the TLC5940-EP enters the dot correction data input mode. The length of input shift
register becomes 96 bits. After all serial data are shifted in, the TLC5940-EP writes the data in the input shift
register to DC register when XLAT is high, and holds the data in the DC register when XLAT is low. The DC
register is a level triggered latch of XLAT signal. Since XLAT is a level-triggered signal, SCLK and SIN must not
be changed while XLAT is high. After XLAT goes low, data in the DC register is latched and does not change.
BLANK signal does not need to be high to latch in new data. XLAT has setup time (tsu1) and hold time (th1) to
SCLK as shown in Figure 16.
DC Mode Data
Input Cycle n
DC Mode Data
Input Cycle n+1
VCC
VPRG
SIN
DC n−1
LSB
DC n
MSB
DC n
MSB−1
DC n
MSB−2
DC n
LSB+1
DC n+1
MSB
DC n
LSB
DC n+1
MSB−1
twh0
SCLK
1
2
3
95
96
1
2
twl0
SOUT
DC n−1
MSB
DC n−1
MSB−1
DC n−1
MSB−2
DC n−1
LSB+1
DC n−1
LSB
DC n
MSB−1
DC n
MSB
DC n
MSB−2
twh2
tsu1
th1
XLAT
Figure 16. Dot Correction Data Input Timing Chart
The TLC5940-EP also has an EEPROM to store dot correction data. To store data from the dot correction
register to EEPROM, DCPRG is set to high after applying VPRG to the VPRG pin. Figure 17 shows the EEPROM
programming timings. The EEPROM has a default value of all 1s.
V(PRG)
VPRG
VCC
tsu6
tprog
th5
DCPRG
XLAT
SIN
DC
MSB
SCLK
1
SOUT
DC
LSB
96
-
DC
MSB
Figure 17. EEPROM Programming Timing Chart
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
19
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
DCPRG
tpd5
tpd5
OUT0
(Current)
OUT15
(Current)
Figure 18. DCPRG and OUTn Timing Diagram
8.4.3 Setting Grayscale
The TLC5940-EP can adjust the brightness of each channel OUTn using a PWM control scheme. The use of 12
bits per channel results in 4096 different brightness steps, respective 0% to 100% brightness. Equation 8
determines the brightness level for each output n:
Brightness in % = GSn × 100
4095
where
•
•
•
GSn = the programmed grayscale value for output n (GSn = 0 to 4095)
n = 0 to 15
Grayscale data for all OUTn
(8)
Figure 19 shows the grayscale data packet format which consists of 12 bits × 16 channels, totaling 192 bits. The
format is Big-Endian format. This means that the MSB is transmitted first, followed by the MSB-1, and so forth.
MSB
191
180
179
12
GS 15.0 GS 14.11
GS 15.11
GS OUT15
GS 1.0
GS OUT14 − GS OUT2
11
LSB
0
GS 0.11
GS 0.0
GS OUT0
Figure 19. Grayscale Data Packet Format
When VPRG is set to GND, the TLC5940-EP enters the grayscale data input mode. The device switches the
input shift register to 192-bit width. After all data is clocked in, a rising edge of the XLAT signal latches the data
into the grayscale register (see Figure 12). New grayscale data immediately becomes valid at the rising edge of
the XLAT signal; therefore, new grayscale data should be latched at the end of a grayscale cycle when BLANK is
high. The first GS data input cycle after dot correction requires an additional SCLK pulse after the XLAT signal to
complete the grayscale update cycle. All GS data in the input shift register is replaced with status information
data (SID) after updated the grayscale register.
8.4.4 Status Information Output
The TLC5940-EP does have a status information register, which can be accessed in grayscale mode
(VPRG=GND). After the XLAT signal latches the data into the GS register the input shift register data will be
replaced with status information data (SID) of the device (see Figure 19). LOD, TEF, and dot correction
EEPROM data (DCPRG=LOW) or dot correction register data (DCPRG=HIGH) can be read out at SOUT pin.
The status information data packet is 192 bits wide. Bits 0-15 contain the LOD status of each channel. Bit 16
contains the TEF status. If DCPRG is low, bits 24-119 contain the data of the dot-correction EEPROM. If DCPRG
is high, bits 24-119 contain the data of the dot-correction register. The remaining bits are reserved. The complete
status information data packet is shown in Figure 20.
SOUT outputs the MSB of the SID at the same time the SID are stored in the SID register, as shown Figure 21.
The next SCLK pulse, which will be the clock for receiving the SMB of the next grayscale data, transmits MSB-1
of SID. If output voltage is < 0.3 V (typical) when the output sink current turns on, LOD status flag becomes
active. The LOD status flag is an internal signal that pulls XERR pin down to low when the LOD status flag
becomes active. The delay time, tpd2 (1 µs maximum), is from the time of turning on the output sink current to
20
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
the time LOD status flag becomes valid. The timing for each channel's LOD status to become valid is shifted by
the 30-ns (maximum) channel-to-channel turnon time. After the first GSCLK goes high, OUT0 LOD status is
valid; tpd3 + tpd2 = 60 ns + 1 µs. OUT1 LOD status is valid; tpd3 + td + tpd2 = 60 ns + 30 ns + 1 µs = 1.09 µs.
OUT2 LOD status is valid; tpd3 + 2*td + tpd2 = 1.12 µs, and so on. It takes 1.51 µs maximum (tpd3 + 15*td +
tpd2) from the first GSCLK rising edge until all LOD become valid; tsuLOD must be > 1.51 µs (see Figure 21) to
ensure that all LOD data are valid.
LSB
MSB
0
15
16
LOD 15
LOD 0
TEF
X
LOD Data
23
24
119
120
191
X
DC 15.5
DC 0.0
X
X
DC Values
TEF
Reserved
Figure 20. Status Information Data Packet Format
VPRG
GS Data Input Mode
XLAT
1st GS Data Input Cycle
GS1
MSB
SIN
2nd GS Data Input Cycle
GS1
LSB
GS2
MSB
> tpd4 + 15 x td + tpd3
tsuLOD
1
SCLK
SOUT
-
192
-
GS2
LSB
193
GS1
MSB
SID1
MSB
192
1
SID1
MSB-1
SID1
LSB
GS2
MSB
(1st GS Data Output Cycle)
BLANK
GSCLK
4096
1
tpd3
OUT0
(current)
td
OUT1
(current)
15 x td
OUT15
(current)
tpd2
XERR
tpd3 + 15 x td + tpd2
Figure 21. Readout Status Information Data (SID) Timing Chart
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
21
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
8.4.5 Grayscale PWM Operation
The grayscale PWM cycle starts with the falling edge of BLANK. The first GSCLK pulse after BLANK goes low
increases the grayscale counter by one and switches on all OUTn with grayscale value not zero. Each following
rising edge of GSCLK increases the grayscale counter by one. The TLC5940-EP compares the grayscale value
of each output OUTn with the grayscale counter value. All OUTn with grayscale values equal to the counter
values are switched off. A BLANK=H signal after 4096 GSCLK pulses resets the grayscale counter to zero and
completes the grayscale PWM cycle (see Figure 22). When the counter reaches a count of FFFh, the counter
stops counting and all outputs turn off. Pulling BLANK high before the counter reaches FFFh immediately resets
the counter to zero.
GS PWM
Cycle n
BLANK
t wl1
t wh1
t h4
GSCLK
1
OUT0
(Current)
OUT1
(Current)
t pd1
t pd1 + td
GS PWM
Cycle n+1
2
t pd3
4096
3
t wl1
t wh3
t su4
1
t pd3
nxt d
t pd3+ n x t d
t pd1 + 15 x td
OUT15
(Current)
t pd2
XERR
Figure 22. Grayscale PWM Cycle Timing Chart
22
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The device is a 16-channel, constant sink current, LED driver. This device can be connected in series to drive
many LED lamps with only a few controller ports. Output current control data, dot correction data and PWM
control data can be written from the SIN input terminal.
9.2 Typical Application
VCC
V(LED)
V(LED)
V(LED)
V(LED)
100 k
OUT0
XERR
SCLK
SCLK
100 nF
BLANK
SOUT
VPRG
VCC
100 nF
XLAT
TLC5940
DCPRG
BLANK
SOUT
XERR
SCLK
XLAT
DCPRG
OUT15
SIN
VCC
GSCLK
GSCLK
OUT0
SOUT
XERR
XLAT
Controller
OUT15
SIN
SIN
GSCLK
TLC5940
DCPRG
IREF
IREF
BLANK
VPRG
IC 0
IC n
W_EEPROM
7
VPRG_D
VPRG_OE
V(22V)
50 k
V(22V)
50 k
50 k
50 k
50 k
50 k
VPRG
Figure 23. Cascading Devices
9.2.1 Design Requirements
For this design example, use the input parameters shown in Table 4.
Table 4. Design Parameters
PARAMETERS
VALUES
VCC input voltage range
3 V to 5.5 V
LED lamp (VLED) input voltage range
>Maximum LED forward voltage (VF) + IC knee voltage
SIN, SCLK, XLAT, GSCLK, and BLANK voltage range
Low level = GND, High level = VCC
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
23
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
9.2.2 Detailed Design Procedures
9.2.2.1 Serial Data Transfer Rate
Figure 23 shows a cascading connection of n TLC5940-EP devices connected to a controller, building a basic
module of an LED display system. The maximum number of cascading TLC5940-EP devices depends on the
application system and is in the range of 40 devices. Equation 9 calculates the minimum frequency needed:
f
4096 × f
(GSCLK) =
(update)
f
× n
193 × f
(SCLK) =
(update)
where
•
•
•
•
f(GSCLK): minimum frequency needed for GSCLK
f(SCLK): minimum frequency needed for SCLK and SIN
f(update): update rate of whole cascading system
n: number cascaded of TLC5940-EP device
(9)
9.2.2.2 Grayscale (GS) Data
There are a total of 16 sets of 12-bit GS data for the PWM control of each output. Select the GS data of each
LED lamp and write the GS data to the register following the signal timing.
9.2.3 Application Curve
Figure 24. Output Waveform with Different Grayscale PWM Data
24
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
10 Power Supply Recommendations
The VCC power supply voltage should be decoupled by placing a 0.1-µF ceramic capacitor close to VCC pin and
GND plane. Depending on panel size, several electrolytic capacitors must be placed on board equally distributed
to get a well-regulated LED supply voltage (VLED). VLED voltage ripple should be less than 5% of its nominal
value. Furthermore, the VLED should be set to the voltage calculated by Equation 10:
VLED > VF + 0.4 V ( 10-mA constant current example)
where
•
Vf = maximum forward voltage of all LEDs
(10)
11 Layout
11.1 Layout Guidelines
1.
2.
3.
4.
Place the decoupling capacitor near the VCC pin and GND plane.
Place the current programming resistor Riref close to IREF pin and IREFGND pin.
Route the GND pattern as widely as possible for large GND currents.
Routing wire between the LED cathode side and the device OUTn pin should be as short and straight as
possible to reduce wire inductance.
5. When several ICs are chained, symmetric placements are recommended.
11.2 Layout Example
GND
VCC
28
1
2
GND
BLANK
XLAT
SCLK
27
26
3
25
4
5
SIN
VPRG
OUT0
GND
6
7
Thermal
Pad
24
23
22
21
OUT1
OUT2
OUT3
8
OUT4
OUT5
OUT6
11
12
13
16
OUT7
14
15
9
10
20
Via to
Heatsink
Layer
19
18
17
VCC
IREF
DCPRG
GSCLK
SOUT
XERR
OUT15
OUT14
OUT13
OUT12
OUT11
OUT10
OUT9
OUT8
Figure 25. Layout Recommendation
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
25
TLC5940-EP
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
www.ti.com
11.3 Power Dissipation Calculation
The device power dissipation must be below the power dissipation rating of the device package to ensure correct
operation. Equation 11 calculates the power dissipation of device:
DC n
x dPWM x N
PD = VCC x ICC + VOUT x IMAX x
63
(
)
(
)
where
•
•
•
•
•
•
•
26
VCC: device supply voltage
ICC: device supply current
VOUT: TLC5940-EP OUTn voltage when driving LED current
IMAX: LED current adjusted by R(IREF) Resistor
DCn: maximum dot correction value for OUTn
N: number of OUTn driving LED at the same time
dPWM: duty cycle defined by BLANK pin or GS PWM value
Submit Documentation Feedback
(11)
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
TLC5940-EP
www.ti.com
SLVSA51E – MARCH 2010 – REVISED SEPTEMBER 2016
12 Device and Documentation Support
12.1 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: TLC5940-EP
27
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TLC5940QPWPREP
ACTIVE
HTSSOP
PWP
28
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TLC5940EP
TLC5940QRHBREP
ACTIVE
VQFN
RHB
32
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TLC
5940EP
V62/10610-01XE
ACTIVE
HTSSOP
PWP
28
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TLC5940EP
V62/10610-01YE
ACTIVE
VQFN
RHB
32
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TLC
5940EP
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of