TLE2074AMFKB

TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 D Direct Upgrades to TL05x, TL07x, and D D TL08x BiFET Operational Amplifiers Greater Than 2× Bandwidth (10 MHz) and 3× Slew Rate (45 V/μs) Than TL07x Ensured Maximum Noise Floor 17 nV/√Hz D On-Chip Offset Voltage Trimming for D Improved DC Performance Wider Supply Rails Increase Dynamic Signal Range to ±19 V description The TLE207x series of JFET-input operational amplifiers more than double the bandwidth and triple the slew rate of the TL07x and TL08x families of BiFET operational amplifiers. Texas Instruments Excalibur process yields a typical noise floor of 11.6 nV/√Hz, 17-nV/√Hz ensured maximum, offering immediate improvement in noise-sensitive circuits designed using the TL07x. The TLE207x also has wider supply voltage rails, increasing the dynamic signal range for BiFET circuits to ±19 V. On-chip zener trimming of offset voltage yields precision grades for greater accuracy in dc-coupled applications. The TLE207x are pin-compatible with lower performance BiFET operational amplifiers for ease in improving performance in existing designs. BiFET operational amplifiers offer the inherently higher input impedance of the JFET-input transistors, without sacrificing the output drive associated with bipolar amplifiers. This makes them better suited for interfacing with high-impedance sensors or very low-level ac signals. They also feature inherently better ac response than bipolar or CMOS devices having comparable power consumption. The TLE207x family of BiFET amplifiers are Texas Instruments highest performance BiFETs, with tighter input offset voltage and ensured maximum noise specifications. Designers requiring less stringent specifications but seeking the improved ac characteristics of the TLE207x should consider the TLE208x operational amplifier family. Because BiFET operational amplifiers are designed for use with dual power supplies, care must be taken to observe common-mode input voltage limits and output swing when operating from a single supply. DC biasing of the input signal is required and loads should be terminated to a virtual ground node at mid-supply. Texas Instruments TLE2426 integrated virtual ground generator is useful when operating BiFET amplifiers from single supplies. The TLE207x are fully specified at ±15 V and ± 5 V. For operation in low-voltage and/or single-supply systems, Texas Instruments LinCMOS families of operational amplifiers (TLC- and TLV-prefix) are recommended. When moving from BiFET to CMOS amplifiers, particular attention should be paid to slew rate and bandwidth requirements and output loading. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright © 1997 − 2004, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071 AVAILABLE OPTIONS PACKAGED DEVICES † TA VIOmax AT 25°C SMALL OUTLINE† (D) CHIP CARRIER (FK) CERAMIC DIP (JG) 0°C to 70°C 2 mV 4 mV TLE2071ACD TLE2071CD — — TLE2071ACP TLE2071CP — −40°C 40°C to 85°C 2 mV 4 mV TLE2071AID TLE2071ID — — TLE2071AIP TLE2071IP — −55°C 55°C to 125°C 2 mV 4 mV — — TLE2071AMFK TLE2071MFK PLASTIC DIP (P) TLE2071AMJG TLE2071MJG — — CERAMIC FLAT PACK (U) TLE2071AMU TLE2071MU The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2071ACDR). TLE2072 AVAILABLE OPTIONS PACKAGED DEVICES † TA VIOmax AT 25°C 0°C to 70°C 3.5 mV 6 mV TLE2072ACD TLE2072CD — — TLE2072ACP TLE2072CP — −40°C 40°C to 85°C 3.5 mV 6 mV TLE2072AID TLE2072ID — — TLE2072AIP TLE2072IP — −55°C 55°C to 125°C 3.5 mV 6 mV SMALL OUTLINE† (D) CHIP CARRIER (FK) CERAMIC DIP (JG) TLE2072AMFK TLE2072MFK — PLASTIC DIP (P) TLE2072AMJG TLE2072MJG — CERAMIC FLAT PACK (U) TLE2072AMU TLE2072MU The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2072ACDR). TLE2074 AVAILABLE OPTIONS PACKAGED DEVICES † TA VIOmax AT 25°C SMALL OUTLINE† (DW) CHIP CARRIER (FK) CERAMIC DIP (J) 0°C to 70°C 3 mV 5 mV TLE2074ACDW TLE2074CDW — — TLE2074ACN TLE2074CN — −40°C 40°C to 85°C 3 mV 5 mV TLE2074AIDW TLE2074IDW — — TLE2074AIN TLE2074IN — −55°C 55°C to 125°C 3 mV 5 mV — TLE2074AMFK TLE2074MFK TLE2074AMJ TLE2074MJ — The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2074ACDWR). symbol IN + + IN − − OUT 2 PLASTIC DIP (N) POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 CERAMIC FLAT PACK (W) TLE2074AMW TLE2074MW TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072 AND TLE2072A D, JG, OR P PACKAGE (TOP VIEW) TLE2071 AND TLE2071A D, JG, OR P PACKAGE (TOP VIEW) 8 2 7 3 6 4 5 NC VCC + OUT OFFSET N2 1OUT 1IN − 1IN + VCC − 1 14 2 13 3 12 4 11 5 10 6 9 7 8 17 6 16 7 15 8 14 9 10 11 12 13 5 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 4OUT 4IN − 4IN + VCC − 3IN + 3IN − 3OUT NC TLE2074M AND TLE2074AM FK PACKAGE (TOP VIEW) NC VCC + NC OUT NC NC 1IN − NC 1IN+ NC 5 17 6 16 7 15 8 14 9 10 11 12 13 TLE2071 AND TLE2071A U PACKAGE (TOP VIEW) NC OFFSET N1 IN − IN + VCC− 1 10 2 9 3 8 4 7 5 6 1IN − 1OUT NC 4OUT 4IN − 3 2 1 20 19 18 NC 4 NC 2OUT NC 2IN − NC 1IN+ NC VCC + NC 2IN+ 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC NC VCC+ OUT OFFSET N2 2IN − 5 6 4 VCC − NC 2IN+ NC 3 2 1 20 19 18 3 VCC + 2OUT 2IN − 2IN+ NC 1OUT NC V CC + NC NC OFFSET N1 NC NC NC 4 7 TLE2072M AND TLE2072AM FK PACKAGE (TOP VIEW) NC VCC − NC OFFSET N2 NC NC IN − NC IN + NC 1OUT 1IN − 1IN + VCC + 2IN + 2IN − 2OUT NC 4OUT 4IN − 4IN + VCC − 3IN + 3IN − 3OUT TLE2071M AND TLE2071AM FK PACKAGE (TOP VIEW) 8 2 TLE2074 AND TLE2074A DW PACKAGE (TOP VIEW) TLE2074 AND TLE2074A J, N, OR W PACKAGE (TOP VIEW) 1OUT 1IN − 1IN + VCC + 2IN + 2IN − 2OUT 1 4IN+ NC VCC − NC 3IN+ NC 3OUT 3IN − 1 2OUT OFFSET N1 IN − IN + VCC − TLE2072 AND TLE2072A U PACKAGE (TOP VIEW) NC 1OUT 1IN− 1IN+ VCC− 1 10 2 9 3 8 4 7 5 6 NC VCC+ 2OUT 2IN− 2IN+ NC − No internal connection POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 R2 Q1 R1 R6 Q11 Q3 R11 Q17 Q8 Q23 D2 R3 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 C1 IN − Q28 Q20 Q13 Q24 D3 Q12 Q4 Q15 R13 Q19 OUT R12 IN + Q30 Q9 Q16 R8 Q5 Q25 C6 C3 Q29 Q18 Q2 D1 Q6 Q14 Q21 Q22 Q26 Q27 Q10 C5 R7 Q31 R4 Q7 R5 C4 R9 C2 OFFSET N1 (see Note A) VCC − NOTES: A. OFFSET N1 AND OFFSET N2 are only availiable on the TLE2071x devices. OFFSET N2 (see Note A) R10 R14 Template Release Date: 7−11−94 VCC + TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 4 equivalent schematic equivalent schematic (continued) TLE2071 TLE2072 TLE2074 Transistors 33 57 114 Resistors COMPONENT ACTUAL DEVICE COMPONENT COUNT 25 37 74 Diodes 8 5 10 Capacitors 6 11 22 5 SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 V Supply voltage, VCC − (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −19 V Differential input voltage range, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC + to VCC − Input voltage range, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC + to VCC − Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 1 mA Output current, IO (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 80 mA Total current into VCC + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 mA Total current out of VCC − . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 mA Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited Package thermal impedance, θJA (see Notes 4 and 5): D package . . . . . . . . . . . . . . . . . . . . . . . . . . 97.1°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . 57.3°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . 79.7°C/W P package . . . . . . . . . . . . . . . . . . . . . . . . . . 84.6°C/W Package thermal impedance, θJC (see Notes 4 and 5): FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6°C/W J package . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1°C/W JG package . . . . . . . . . . . . . . . . . . . . . . . . . 14.5°C/W U package . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7°C/W W package . . . . . . . . . . . . . . . . . . . . . . . . . . . 10°C/W Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: DW or N package . . . . . . . . . . . . . . . 260°C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J, JG, U, or W package . . . . . . . . . . 300°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC + and VCC − . 2. Differential voltages are at the noninverting input with respect to the inverting input. 3. The output may be shorted to either supply. Temperatures and/or supply voltages must be limited to ensure that the maximum dissipation rate is not exceeded. 4. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. 5. The package thermal impedance is calculated in accordance with JESD 51-7 (plastic) or MIL-STD-883 Method 1012 (ceramic). recommended operating conditions Supply voltage, VCC± Common mode input voltage, Common-mode voltage VIC I SUFFIX M SUFFIX MAX MIN MAX MIN MAX ± 2.25 ± 19 ± 2.25 ± 19 ± 2.25 ± 19 VCC ± = ± 5 V −0.9 5 −0.8 5 −0.8 5 VCC ± = ±15 V −10.9 15 −10.8 15 −10.8 15 0 70 −40 85 −55 125 Operating free-air temperature, TA 6 C SUFFIX MIN POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT V V °C TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) PARAMETER TA† TEST CONDITIONS TLE2071C MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω VO = 0, IIB Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ± 2 2.3 3V RL = 2 kΩ RL = 10 kΩ ri ci † Input resistance Input capacitance MAX 0.3 2 4 Full range 25°C 3.8 Full range 3.7 25°C 3.5 Full range 3.4 25°C 1.5 Full range 1.5 25°C −3.5 Full range −3.4 25°C −3.7 Full range −3.6 25°C −1.5 Full range −1.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 29 μV/°C 5 100 5 100 pA 1.4 nA 15 175 15 175 pA 5 nA 5 to −1.9 5 to −1 5 to −1.9 V 5 to −0.9 4.1 3.8 4.1 3.7 3.9 3.5 3.9 V 3.4 2.3 1.5 2.3 1.5 −4.2 −3.5 −4.2 −3.4 −4.1 −3.7 −4.1 V −3.6 −2.4 −1.5 −2.4 −1.5 91 80 91 79 100 90 100 dB 89 106 95 106 94 25°C 1012 1012 Common mode 25°C 11 11 Differential 25°C 2.5 2.5 25°C 80 80 zo Open-loop output impedance f = 1 MHz CMRR Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω kSVR Supply voltage rejection Supply-voltage ratio(ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 70 Full range 68 25°C 82 Full range 80 mV 3.2 5 5 to −1 UNIT 29 1.4 5 to −0.9 VIC = 0 VIC = 0, See Figure 5 TYP 3.2 Full range 25°C 25 C VICR 4 Full range 25°C Input bias current 0.34 MIN 6 25°C VO = 0, MAX Full range Full range VIC = 0, See Figure 4 TLE2071AC TYP 89 70 82 80 pF Ω 89 dB 68 99 Ω 99 dB Full range is 0°C to 70°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) (continued) PARAMETER TEST CONDITIONS ICC Supply current VO = 0, 0 IOS Short-circuit Short circuit output current VO = 0 † No load TLE2071C MIN TYP MAX MIN TYP MAX 25°C 1.35 1.6 2.2 1.35 1.6 2.2 Full range VID = 1 V VID = − 1 V TLE2071AC TA† 2.2 25°C 2.2 −35 −35 45 45 UNIT mA mA Full range is 0°C to 70°C. TLE2071C operating characteristics at specified free-air temperature, VCC ± = ±5 V PARAMETER TEST CONDITIONS TA† TLE2071C MIN TYP 25°C SR + Positive slew rate SR − Negative slew rate ts Settling time Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent Peak-to-peak input noise voltage VO(PP) = ± 2.3 V, AVD = − 1 1, RL = 2 kΩ kΩ, CL = 100 pF, See Figure 1 Full range AVD = − 1, 2-V step, RL = 1 kΩ, CL = 100 pF MIN TYP MAX V/μs 23 38 38 23 V/μs 23 To 10 mV 0.25 0.25 0.4 0.4 μss 25°C To 1 mV f = 10 kHz f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT 35 23 f = 10 Hz RS = 20 Ω, See Figure 3 MAX 35 25°C Full range TLE2071AC 25°C 48 85 48 85 12 17 12 17 6 6 0.6 0.6 2.8 2.8 nV/√Hz μV 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C THD + N Total harmonic distortion plus noise VO(PP) = 5 V, kHz f = 1 kHz, RS = 25 Ω AVD = 10, kΩ, RL = 2 kΩ 25°C B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 94 9.4 94 9.4 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 4 V, RL = 2 kΩ , AVD = − 1, CL = 25 pF 25°C 28 2.8 28 2.8 MHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 56° 56° † 8 0 013% 0.013% Full range is 0°C to 70°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 fA/√Hz 0 013% 0.013% TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) PARAMETER TA† TEST CONDITIONS TLE2071C MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω VO = 0, IIB Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ±10 V RL = 2 kΩ RL = 10 kΩ ri ci † Input resistance Input capacitance MAX 0.47 2 4 Full range 25°C 13.8 Full range 13.7 25°C 13.5 Full range 13.4 25°C 11.5 Full range 11.5 25°C −13.8 Full range −13.7 25°C −13.5 Full range −13.4 25°C −11.5 Full range −11.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 29 μV/°C 6 100 6 100 pA 1.4 nA 20 175 20 175 pA 5 nA 15 to −11.9 15 to −11 15 to −11.9 V 15 to −10.9 14.1 13.8 14.1 13.7 13.9 13.5 13.9 V 13.4 12.3 11.5 12.3 11.5 −14.2 −13.8 −14.2 −13.7 −14 −13.5 −14 V −13.4 −12.4 −11.5 −12.4 −11.5 96 80 96 79 109 90 109 dB 89 118 95 118 94 25°C 1012 1012 Common mode 25°C 7.5 7.5 Differential 25°C 2.5 2.5 25°C 80 80 zo Open-loop output impedance f = 1 MHz CMRR Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω kSVR Supply voltage rejection Supply-voltage ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 80 Full range 79 25°C 82 Full range 80 mV 3.2 5 15 to −11 UNIT 29 1.4 15 to −10.9 VIC = 0 VIC = 0, See Figure 5 TYP 3.2 Full range 25°C 25 C VICR 4 Full range 25°C Input bias current 0.49 MIN 6 25°C VO = 0, MAX Full range Full range VIC = 0, See Figure 4 TLE2071AC TYP 98 80 82 81 pF Ω 98 dB 79 99 Ω 99 dB Full range is 0°C to 70°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued) PARAMETER † TEST CONDITIONS ICC Supply current VO = 0, 0 IOS Short-circuit output current VO = 0 No load TLE2071C MIN TYP MAX MIN TYP MAX 25°C 1.35 1.7 2.2 1.35 1.7 2.2 Full range VID = 1 V VID = − 1 V TLE2071AC TA† 25°C 2.2 2.2 −30 −45 −30 −45 30 48 30 48 UNIT mA mA Full range is 0°C to 70°C. TLE2071C operating characteristics at specified free-air temperature, VCC ± = ±15 V PARAMETER SR + TEST CONDITIONS Positive slew rate VO(PP) = 10 V, RL = 2 kΩ, kΩ See Figure 1 SR − ts Vn VN(PP) † AVD = − 1, CL = 100 pF, pF Negative slew rate Settling time AVD = − 1, 10-V step, RL = 1 kΩ, CL = 100 pF TLE2071C MIN TYP 25°C 30 40 Full range 27 25°C 30 Full range 27 MAX 45 MIN TYP 30 40 MAX 30 45 V/μs 0.4 0.4 1.5 1.5 μss 25°C To 1 mV 25°C f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT V/μs 27 To 10 mV f = 10 kHz RS = 20 Ω, See Figure 3 TLE2071AC 27 f = 10 Hz Equivalent input noise voltage Peak to peak equivalent Peak-to-peak input p noise voltage g TA† 48 85 48 85 12 17 12 17 6 6 06 0.6 06 0.6 28 2.8 28 2.8 nV√Hz μV V 25°C In Equivalent input noise current VIC = 0 0, f = 10 kHz 25°C THD + N Total harmonic distortion plus noise VO(PP) = 20 V, f = 1 kHz kHz, RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 8 10 8 10 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 20 V, RL = 2 kΩ, AVD = − 1, CL = 25 pF 25°C 478 637 478 637 kHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 0 008% 0.008% Full range is 0°C to 70°C. 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 57° fA/√Hz 0 008% 0.008% 57° TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071I electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) PARAMETER TA† TEST CONDITIONS TLE2071I MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω, VO = 0, 0.34 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ±2 ±2.3 3V RL = 2 kΩ RL = 10 kΩ ri ci † Input resistance Input capacitance 0.3 Full range 25°C 3.8 Full range 3.7 25°C 3.5 Full range 3.4 25°C 1.5 Full range 1.5 25°C −3.8 Full range −3.7 25°C −3.5 Full range −3.4 25°C −1.5 Full range −1.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 5 100 5 100 pA 5 nA 15 175 15 175 pA 10 nA 5 to −1.9 5 to −1 5 to −1.9 V 5 to −0.8 4.1 3.8 4.1 3.7 3.9 3.5 3.9 V 3.4 2.3 1.5 2.3 1.5 −4.2 −3.8 −4.2 −3.7 −4.1 −3.5 −4.1 V −3.4 −2.4 −1.5 −2.4 −1.5 91 80 91 79 100 90 100 dB 89 106 95 106 94 1012 Common mode 25°C 11 11 Differential 25°C 2.5 2.5 25°C 80 80 f = 1 MHz CMRR Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω kSVR Supply voltage rejection Supply-voltage ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 70 Full range 68 25°C 82 Full range 80 mV μV/°C 1012 Open-loop output impedance 2 29 25°C zo UNIT 3.2 10 5 to −1 MAX 5.6 5 5 to −0.8 VIC = 0 VIC = 0, See Figure 5 4 TYP 29 Full range 25°C 25 C MIN 3.2 Full range 25°C Input bias current TLE2071AI MAX 7.6 25°C VIC = 0, See Figure 4 TYP 89 70 82 80 pF Ω 89 dB 68 99 Ω 99 dB Full range is − 40°C to 85°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071I electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) (continued) PARAMETER † TEST CONDITIONS ICC Supply current VO = 0, 0 IOS Short-circuit Short circuit output current VO = 0 No load TLE2071I MIN TYP MAX MIN TYP MAX 25°C 1.35 1.6 2.2 1.35 1.6 2.2 Full range VID = 1 V VID = − 1 V TLE2071AI TA† 2.2 25°C 2.2 −35 −35 45 45 UNIT mA mA Full range is − 40°C to 85°C. TLE2071I operating characteristics at specified free-air temperature, VCC ± = ±5 V PARAMETER TEST CONDITIONS TA† TLE2071I MIN TYP 25°C SR + Positive slew rate SR − Negative slew rate ts † Settling time Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent Peak-to-peak input p noise voltage g VO(PP) = ± 2.3 V, AVD = − 1 1, RL = 2 kΩ, kΩ CL = 100 pF, See Figure 1 Full range AVD = − 1, 2-V step, RL = 1 kΩ, CL = 100 pF MIN TYP MAX V/μs 22 38 38 22 V/μs 22 To 10 mV 0.25 0.25 0.4 0.4 μss 25°C To 1 mV f = 10 kHz 25°C f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT 35 22 f = 10 Hz RS = 20 Ω, See Figure 3 MAX 35 25°C Full range TLE2071AI 48 85 48 85 12 17 12 17 6 6 06 0.6 06 0.6 nV/√Hz μV V 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 5 V, AVD = 10, kHz kΩ, f = 1 kHz, RL = 2 kΩ RS = 25 Ω 25°C 0 013% 0.013% 0 013% 0.013% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, 25°C 94 9.4 94 9.4 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 4 V, AVD = − 1, RL = 2 kΩ , CL = 25 pF 25°C 28 2.8 28 2.8 MHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, 25°C 56° 56° RL = 2 kΩ, See Figure 2 RL = 2 kΩ, See Figure 2 Full range is − 40°C to 85°C. 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 fA/√Hz TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071I electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) PARAMETER TA† TEST CONDITIONS TLE2071I MIN TYP 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω, VO = 0, 0.49 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ± 10 V RL = 2 kΩ RL = 10 kΩ ri ci Input capacitance Full range 15 to −10.8 25°C 13.8 Full range 13.7 25°C 13.5 Full range 13.4 25°C 11.5 Full range 11.5 25°C −13.8 Full range −13.7 25°C −13.5 Full range −13.4 25°C −11.5 Full range −11.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 29 μV/°C 6 100 6 100 pA 5 nA 20 175 20 175 pA 10 nA VIC = 0, See Figure 5 15 to −11.9 15 to −11 15 to −11.9 V 15 to −10.8 14.1 13.8 14.1 13.7 13.9 13.5 13.9 V 13.4 12.3 11.5 12.3 11.5 −14.2 −13.8 −14.2 −13.7 −14 −13.5 −14 V −13.4 −12.4 −11.5 −12.4 −11.5 96 80 96 79 109 90 109 dB 89 118 95 118 94 25°C 1012 1012 Common mode 25°C 7.5 7.5 Differential 25°C 2.5 2.5 80 80 VIC = 0 Open-loop output impedance f = 1 MHz 25°C Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0 0, RS = 50 Ω 25°C 80 CMRR Full range 79 Supply voltage rejection Supply-voltage ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 82 Full range 80 mV 3.2 10 15 to −11 UNIT 2 5.6 5 zo kSVR † Input resistance 0.47 MAX 29 Full range 25°C 25 C 4 TYP 3.2 Full range 25°C Input bias current MIN 7.6 25°C VIC = 0, See Figure 4 TLE2071AI MAX 98 80 Ω pF Ω 98 dB 79 99 82 80 99 dB Full range is − 40°C to 85°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071I electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued) PARAMETER † TEST CONDITIONS ICC Supply current VO = 0, 0 IOS Short-circuit output current VO = 0 No load TLE2071I MIN TYP MAX MIN TYP MAX 25°C 1.35 1.7 2.2 1.35 1.7 2.2 Full range VID = 1 V 25°C VID = − 1 V TLE2071AI TA† 2.2 2.2 −30 −45 −30 −45 30 48 30 48 UNIT mA mA Full range is − 40°C to 85°C. TLE2071I operating characteristics at specified free-air temperature, VCC ± = ±15 V PARAMETER SR + Positive slew rate SR − Negative slew rate ts † Settling time Vn Equivalent input noise voltage VN(PP) ( ) Peak-to-peak Peak to peak equivalent input noise voltage TEST CONDITIONS TA† VO(PP) = ± 10 V, AVD = − 1 1, RL = 2 kΩ kΩ, CL = 100 pF, pF See Figure 1 AVD = − 1, 10-V step, RL = 1 kΩ, CL = 100 pF TYP 25°C 30 40 Full range 24 25°C 30 Full range 24 TLE2071AI MAX MIN TYP 30 40 MAX 45 30 45 V/μs 24 0.4 0.4 1.5 1.5 μs 25°C To 1 mV 25°C f = 10 kHz f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT V/μs 24 To 10 mV f = 10 Hz RS = 20 Ω, See Figure 3 g TLE2071I MIN 48 85 48 85 12 17 12 17 6 6 0.6 0.6 nV/√Hz μV 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 20 V, f = 1 kHz, kHz RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 008% 0.008% 0 008% 0.008% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 8 10 8 10 MHz BOM O Maximum output-swing output swing bandwidth VO(PP) = 20 V, RL = 2 kΩ, AVD = − 1, CL = 25 pF 25°C 478 637 478 637 kHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C Full range is − 40°C to 85°C. 14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 57° 57° fA/√Hz TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) PARAMETER TA† TEST CONDITIONS TLE2071M MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω, VO = 0, TYP 0.34 Full range 25°C IIB VO = 0, VICR Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification ±2.3 3V VO = ±2 RL = 2 kΩ RL = 10 kΩ ri ci † Input resistance Input capacitance Full range 25°C 3.8 Full range 3.6 25°C 3.5 Full range 3.3 25°C 1.5 Full range 1.4 25°C −3.8 Full range −3.6 25°C −3.5 Full range −3.3 25°C −1.5 Full range −1.4 25°C 80 Full range 78 25°C 90 Full range 88 25°C 95 Full range 93 29} μV/°C 5 100 5 100 pA 20 nA 15 175 15 175 pA 60 nA 5 to −1.9 5 to −1 5 to −1.9 V 5 to −0.8 4.1 3.8 4.1 3.6 3.9 3.5 3.9 V 3.3 2.3 1.5 2.3 1.4 −4.2 −3.8 −4.2 −3.6 −4.1 −3.5 −4.1 V −3.3 −2.4 −1.5 −2.4 −1.4 91 80 91 78 100 90 100 dB 88 106 95 106 93 25°C 1012 1012 Common mode 25°C 11 11 Differential 25°C 2.5 2.5 25°C 80 80 zo Open-loop output impedance f = 1 MHz CMRR Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω kSVR Supply voltage rejection Supply-voltage ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 70 Full range 68 25°C 82 Full range 80 mV 3.2 60 5 to −1 UNIT 2 7.2 20 5 to −0.8 VIC = 0 VIC = 0, See Figure 5 0.3 MAX 29} Full range 25°C 25 C 4 TYP 3.2 Full range 25°C Input bias current MIN 9.2 Full range VIC = 0, See Figure 4 TLE2071AM MAX 89 70 82 80 pF Ω 89 dB 68 99 Ω 99 dB Full range is − 55°C to 125°C. products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. ‡ ∗On POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) PARAMETER † TEST CONDITIONS ICC Supply current VO = 0, 0 IOS Short-circuit output current VO = 0 No load TLE2071M MIN TYP MAX MIN TYP MAX 25°C 1.35 1.6 2.2 1.35 1.6 2.2 Full range VID = 1 V VID = − 1 V TLE2071AM TA† 2.2 2.2 −35 −35 45 45 25°C UNIT mA mA Full range is − 55°C to 125°C. TLE2071M operating characteristics at specified free-air temperature, VCC ± = ±5 V PARAMETER TEST CONDITIONS TA† TLE2071M MIN TYP 25°C SR + Positive slew rate SR − Negative slew rate ts Vn VN(PP) † Settling time VO(PP) = ± 2.3 V, AVD = − 1 1, RL = 2 kΩ kΩ, CL = 100 pF, See Figure 1 AVD = − 1, 2-V step, RL = 1 kΩ, CL = 100 pF MIN TYP MAX V/μs 20} 38 38 20} V/μs 20} To 10 mV 0.25 0.25 0.4 0.4 μss 25°C To 1 mV f = 10 kHz 25°C f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT 35 20} f = 10 Hz RS = 20 Ω, See Figure 3 g MAX 35 25°C Full range Equivalent input noise voltage Peak-to-peak equivalent input noise voltage Full range TLE2071AM 48 85} 48 85} 12 17} 12 17} 6 6 06 0.6 06 0.6 nV/√Hz V μV 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 5 V, f = 1 kHz, kHz RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 013% 0.013% 0 013% 0.013% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 94 9.4 94 9.4 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 4 V, RL = 2 kΩ , AVD = − 1, CL = 25 pF 25°C 28 2.8 28 2.8 MHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 56° 56° Full range is − 55°C to 125°C. products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. ‡ ∗On 16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 fA/√Hz TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071M electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) PARAMETER TA† TEST CONDITIONS TLE2071M MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω VO = 0, 0.49 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ±10 V RL = 2 kΩ RL = 10 kΩ ri ci Input resistance Input capacitance 0.47 Full range 25°C 13.8 Full range 13.6 25°C 13.5 Full range 13.3 25°C 11.5 Full range 11.4 25°C −13.8 Full range −13.6 25°C −13.5 Full range −13.3 25°C −11.5 Full range −11.4 25°C 80 Full range 78 25°C 90 Full range 88 25°C 95 Full range 93 6 100 6 100 pA 20 nA 20 175 20 175 pA 60 nA 15 to −11.9 15 to −11 15 to −11.9 V 15 to −10.9 14.1 13.8 14.1 13.6 13.9 13.5 13.9 V 13.3 12.3 11.5 12.3 11.4 −14.2 −13.8 −14.2 −13.6 −14 −13.5 −14 V −13.3 −12.4 −11.5 −12.4 −11.4 96 80 96 78 109 90 109 dB 88 118 95 118 93 1012 Common mode 25°C 7.5 7.5 Differential 25°C 2.5 2.5 25°C 80 80 f = 1 MHz CMRR Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω kSVR Supply voltage rejection Supply-voltage ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 80 Full range 78 25°C 82 Full range 80 mV μV/°C 1012 Open-loop output impedance 2 29∗ 25°C zo UNIT 3.2 60 15 to −11 MAX 7.2 20 15 to −10.9 VIC = 0 VIC = 0, See Figure 5 4 TYP 29∗ Full range 25°C 25 C MIN 3.2 Full range 25°C Input bias current TLE2071AM MAX 9.2 25°C VIC = 0, See Figure 4 TYP 98 80 82 80 pF Ω 98 dB 78 99 Ω 99 dB ∗On † products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. Full range is − 55°C to 125°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 17 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071M electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued) PARAMETER † TEST CONDITIONS ICC Supply current VO = 0, 0 IOS Short circuit output current Short-circuit VO = 0 No load TLE2071M MIN TYP MAX MIN TYP MAX 25°C 1.35 1.7 2.2 1.35 1.7 2.2 Full range VID = 1 V VID = − 1 V TLE2071AM TA† 25°C 2.2 2.2 −30 −45 −30 −45 30 48 30 48 UNIT mA mA Full range is − 55°C to 125°C. TLE2071M operating characteristics at specified free-air temperature, VCC ± = ±15 V PARAMETER SR + TEST CONDITIONS Positive slew rate VO(PP) = 10 V, RL = 2 kΩ kΩ, See Figure 1 SR − ts Vn VN(PP) AVD = − 1, CL = 100 pF, pF Negative slew rate Settling time AVD = − 1, 10-V step, RL = 1 kΩ, CL = 100 pF TLE2071M MIN TYP 25°C 30 40 Full range 22 25°C 30 Full range 22 MIN TYP 30 40 MAX 30 45 V/μs 0.4 0.4 1.5 1.5 μss 25°C To 1 mV 25°C f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT V/μs 22 48 85∗ 48 85∗ 12 17∗ 12 17∗ 6 6 06 0.6 06 0.6 nV/√Hz μV V 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 20 V, f = 1 kHz, kHz RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 008% 0.008% 0 008% 0.008% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 8∗ 10 8∗ 10 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 20 V, RL = 2 kΩ, AVD = − 1, CL = 25 pF 25°C 478∗ 637 478∗ 637 kHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C ∗On † MAX 45 To 10 mV f = 10 kHz RS = 20 Ω, See Figure 3 TLE2071AM 22 f = 10 Hz Equivalent input noise voltage Peak to peak equivalent Peak-to-peak input p noise voltage g TA† products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. Full range is − 55°C to 125°C. 18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 57° 57° fA/√Hz TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2071Y electrical characteristics at VCC ± = ±15 V, TA = 25°C PARAMETER VIO Input offset voltage IIO Input offset current IIB Input bias current VICR Common-mode Common mode input voltage range VOM + VOM − AVD ri TEST CONDITIONS VIC = 0, VO = 0, VIC = 0, 0 VO = 0, 0 RS = 50 Ω See Figure 4 Maximum negative peak output voltage swing Large-signal Large signal differential voltage amplification Input resistance TYP 4 mV 100 pA 20 175 pA IO = − 200 μA 13.8 14.1 IO = − 2 mA 13.5 13.9 IO = − 20 mA 11.5 12.3 IO = 200 μA −13.8 −14.2 IO = 2 mA −13.5 −14 IO = 20 mA −11.5 −12.4 RL = 600 Ω 80 96 RL = 2 kΩ 90 109 RL = 10 kΩ 95 118 Common mode 7.5 Differential 2.5 ci Input capacitance VO = 0, See Figure 5 zo Open-loop output impedance f = 1 MHz CMRR Common-mode rejection ratio VIC = VICRmin, RS = 50 Ω VO = 0, kSVR Supply-voltage rejection ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ±15 V, RS = 50 Ω VO = 0, ICC Supply current VO = 0, IOS Short circuit output current Short-circuit VO = 0 POST OFFICE BOX 655303 V V V dB Ω 1012 VIC = 0 UNIT 6 15 to 11.9 VO = ±10 V MAX 0.49 15 to −11 RS = 50 Ω Maximum positive peak output voltage swing TLE2071Y MIN pF 80 Ω 80 98 dB 82 99 dB No load 1.35 1.7 VID = 1 V −30 −45 30 48 VID = − 1 V • DALLAS, TEXAS 75265 2.2 mA mA 19 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) TLE2072C PARAMETER TEST CONDITIONS TA† MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω VO = 0, 0.9 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification ±2.3 3V VO = ±2 RL = 2 kΩ RL = 10 kΩ ri ci † Input resistance Input capacitance 0.65 3.5 5.3 Full range 25°C 3.8 Full range 3.7 25°C 3.5 Full range 3.4 25°C 1.5 Full range 1.5 25°C −3.8 Full range −3.7 25°C −3.5 Full range −3.4 25°C −1.5 Full range −1.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 μV/°C 5 100 5 100 pA 1.4 nA 15 175 15 175 pA 5 nA 5 to −1.9 5 to −1 5 to −1.9 V 5 to −0.9 4.1 3.8 4.1 3.7 3.9 3.5 3.9 V 3.4 2.3 1.5 2.3 1.5 −4.2 −3.8 −4.2 −3.7 −4.1 −3.5 −4.1 V −3.4 −2.4 −1.5 −2.4 −1.5 91 80 91 79 100 90 100 dB 89 106 95 106 94 1012 1012 Common mode 25°C 11 11 Differential 25°C 2.5 2.5 25°C 80 80 Open-loop output impedance f = 1 MHz CMRR Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω kSVR Supply voltage rejection Supply-voltage ratio(ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 70 Full range 68 25°C 82 Full range 80 Full range is 0°C to 70°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mV 25 5 5 to −1 UNIT 2.3 25°C zo 20 MAX 1.4 5 to −0.9 VIC = 0 VIC = 0, See Figure 5 6 TYP 25 Full range 25°C 25 C MIN 2.3 Full range 25°C Input bias current TLE2072AC MAX 7.8 25°C VIC = 0, See Figure 4 TYP 89 70 82 80 pF Ω 89 dB 68 99 Ω 99 dB TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) (continued) TLE2072C PARAMETER TEST CONDITIONS ICC Supply current (both channels) VO = 0, 0 ax Crosstalk attenuation VIC = 0, IOS Short-circuit Short circuit output current No load RL = 2 kΩ VO = 0 MIN TYP MAX MIN TYP MAX 25°C 2.7 2.9 3.9 2.7 2.9 3.9 Full range VID = 1 V VID = − 1 V TLE2072AC TA 3.9 25°C 3.9 120 120 −35 −35 45 45 25°C UNIT mA dB mA TLE2072C operating characteristics at specified free-air temperature, VCC ± = ±5 V TLE2072C PARAMETER TEST CONDITIONS TA† MIN 25°C SR + Positive slew rate SR − Negative slew rate ts † Settling time Vn Equivalent input noise voltage VN(PP) Peak-to-peak equivalent input noise voltage VO(PP) = ± 2.3 V, AVD = − 1 1, RL = 2 kΩ, kΩ CL = 100 pF, See Figure 1 Full range AVD = − 1, 2-V step, RL = 1 kΩ, CL = 100 pF To 10 mV MIN TYP MAX To 1 mV f = 10 kHz 25°C 22 V/μs 22 38 38 22 V/μs 22 0.25 0.25 0.4 0.4 μss 48 85 48 85 12 17 12 17 f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT 35 25°C f = 10 Hz RS = 20 Ω, See Figure 3 TLE2072AC MAX 35 25°C Full range TYP 6 6 0.6 0.6 nV/√Hz V μV 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 5 V, f = 1 kH kHz, RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 013% 0.013% 0 013% 0.013% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 94 9.4 94 9.4 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 4 V, RL = 2 kΩ , AVD = − 1, CL = 25 pF 25°C 28 2.8 28 2.8 MHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 56° 56° fA /√Hz Full range is 0°C to 70°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 21 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) TLE2072C PARAMETER TEST CONDITIONS TA† MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω VO = 0, 1.1 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ±10 V RL = 2 kΩ RL = 10 kΩ ri ci † Input resistance Input capacitance 0.7 3.5 5.3 15 to −11 Full range 25°C 13.8 Full range 13.6 25°C 13.5 Full range 13.4 25°C 11.5 Full range 11.5 25°C −13.8 Full range −13.7 25°C −13.5 Full range −13.4 25°C −11.5 Full range −11.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 μV/°C 6 100 6 100 pA 1.4 nA 20 175 20 175 pA 5 nA 15 to −11.9 15 to −11 15 to −11.9 V 15 to −10.9 14.1 13.8 14.1 13.6 13.9 13.5 13.9 V 13.4 12.3 11.5 12.3 11.5 −14.2 −13.8 −14.2 −13.7 −14 −13.5 −14 V −13.4 −12.4 −11.5 −12.4 −11.5 96 80 96 79 109 90 109 dB 89 118 95 118 94 1012 1012 Common mode 25°C 7.5 7.5 Differential 25°C 2.5 2.5 25°C 80 80 f = 1 MHz Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω 25°C 80 CMRR Full range 79 Supply voltage rejection Supply-voltage ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 82 kSVR Full range 81 Full range is 0°C to 70°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mV 25 25°C Open-loop output impedance UNIT 2.4 5 zo 22 MAX 1.4 15 to −10.9 VIC = 0 VIC = 0, See Figure 5 6 TYP 25 Full range 25°C 25 C MIN 2.4 Full range 25°C Input bias current TLE2072AC MAX 7.8 25°C VIC = 0, See Figure 4 TYP 98 80 82 81 pF Ω 98 dB 79 99 Ω 99 dB TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued) TLE2072C PARAMETER TEST CONDITIONS ICC Supply current (both channels) VO = 0, 0 No load ax Crosstalk attenuation VIC = 0, RL = 2 kΩ IOS Short circuit output current Short-circuit VO = 0 MIN TYP MAX MIN TYP MAX 25°C 2.7 3.1 3.9 2.7 3.1 3.9 Full range VID = 1 V VID = − 1 V TLE2072AC TA 3.9 25°C 3.9 120 120 −30 −45 −30 −45 30 48 30 48 25°C UNIT mA dB mA TLE2072C operating characteristics at specified free-air temperature, VCC ± = ±15 V TLE2072C PARAMETER SR + TEST CONDITIONS Positive slew rate VO(PP) = 10 V, AVD = − 1 1, CL = 100 pF, SR − ts † RL = 2 kΩ kΩ, See Figure 1 Negative slew rate Settling time Vn Equivalent input noise voltage VN(PP) Peak-to-peak equivalent input noise voltage AVD = − 1, 10-V step, RL = 1 kΩ, CL = 100 pF TA† MIN TYP 25°C 28 40 Full range 25 25°C 30 Full range 25 To 10 mV MAX MIN TYP 28 40 MAX 45 30 45 V/μs 25 0.4 0.4 1.5 1.5 μss To 1 mV f = 10 kHz 25°C 48 85 48 85 12 17 12 17 f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT V/μs 25 25°C f = 10 Hz RS = 20 Ω, See Figure 3 TLE2072AC 6 6 0.6 0.6 nV/√Hz μV V 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 20 V, f = 1 kH kHz, RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 008% 0.008% 0 008% 0.008% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 8 10 8 10 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 20 V, RL = 2 kΩ, AVD = − 1, CL = 25 pF 25°C 478 637 478 637 kHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 57° fA /√Hz 57° Full range is 0°C to 70°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 23 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072I electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) TLE2072I PARAMETER TEST CONDITIONS TA† MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω, VO = 0, 0.9 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ±2 ±2.3 3V RL = 2 kΩ RL = 10 kΩ ri ci † Input resistance Input capacitance 0.65 3.5 6.4 5 to −1 Full range 25°C 3.8 Full range 3.7 25°C 3.5 Full range 3.4 25°C 1.5 Full range 1.5 25°C −3.8 Full range −3.7 25°C −3.5 Full range −3.4 25°C −1.5 Full range −1.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 μV/°C 5 100 5 100 pA 5 nA 15 175 15 175 pA 10 nA 5 to −1.9 5 to −1 5 to −1.9 V 5 to −0.8 4.1 3.8 4.1 3.7 3.9 3.5 3.9 V 3.4 2.3 1.5 2.3 1.5 −4.2 −3.8 −4.2 −3.7 −4.1 −3.5 −4.1 V −3.4 −2.4 −1.5 −2.4 −1.5 91 80 91 79 100 90 100 dB 89 106 95 106 94 1012 1012 Common mode 25°C 11 11 Differential 25°C 2.5 2.5 25°C 80 80 f = 1 MHz Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω 25°C 70 CMRR Full range 68 Supply voltage rejection Supply-voltage ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 82 kSVR Full range 80 Full range is − 40°C to 85°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mV 25 25°C Open-loop output impedance UNIT 2.4 10 zo 24 MAX 5 5 to −0.8 VIC = 0 VIC = 0, See Figure 5 6 TYP 25 Full range 25°C 25 C MIN 2.4 Full range 25°C Input bias current TLE2072AI MAX 9.1 25°C VIC = 0, See Figure 4 TYP 89 70 82 80 pF Ω 89 dB 68 99 Ω 99 dB TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072I electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) (continued) TLE2072I PARAMETER TEST CONDITIONS ICC Supply current (both channels) VO = 0, 0 ax Crosstalk attenuation VIC = 0, IOS Short circuit output current Short-circuit No load RL = 2 kΩ VO = 0 MIN TYP MAX MIN TYP MAX 25°C 2.7 2.9 3.9 2.7 2.9 3.9 Full range 3.9 25°C VID = 1 V 25°C VID = − 1 V TLE2072AI TA 3.9 120 120 −35 −35 45 45 UNIT mA dB mA TLE2072I operating characteristics at specified free-air temperature, VCC ± = ±5 V TLE2072I PARAMETER TEST CONDITIONS TA† MIN 25°C SR + Positive slew rate SR − Negative slew rate ts † Settling time Vn Equivalent input noise voltage VN(PP) Peak-to-peak equivalent input noise voltage VO(PP) = ± 2.3 V, AVD = − 1 1, RL = 2 kΩ kΩ, CL = 100 pF, See Figure 1 Full range AVD = − 1, 2-V step, RL = 1 kΩ, CL = 100 pF To 10 mV TLE2072AI MAX MIN 35 TYP MAX V/μs 20 38 38 20 V/μs 20 0.25 0.25 0.4 0.4 μss 25°C To 1 mV f = 10 Hz f = 10 kHz RS = 20 Ω, See Figure 3 25°C f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT 35 20 25°C Full range TYP 48 85 48 85 12 17 12 17 6 6 06 0.6 06 0.6 nV/√Hz μV V 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 5 V, f = 1 kHz, kH RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 013% 0.013% 0 013% 0.013% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 94 9.4 94 9.4 MHz BOM Maximum output outputswing bandwidth VO(PP) = 4 V, RL = 2 kΩ , AVD = − 1, CL = 25 pF 25°C 28 2.8 28 2.8 MHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 56° 56° fA /√Hz Full range is 40°C to 85°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 25 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072I electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) TLE2072I PARAMETER TEST CONDITIONS TA† MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω, VO = 0, 1.1 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ±10 V RL = 2 kΩ RL = 10 kΩ ri ci † Input resistance Input capacitance 0.7 3.5 6.4 15 to −11 Full range 25°C 13.8 Full range 13.7 25°C 13.5 Full range 13.4 25°C 11.5 Full range 11.5 25°C −13.8 Full range −13.7 25°C −13.5 Full range −13.4 25°C −11.5 Full range −11.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 μV/°C 6 100 6 100 pA 5 nA 20 175 20 175 pA 10 nA 15 to −11.9 15 to −11 15 to −11.9 V 15 to −10.8 14.1 13.8 14.1 13.7 13.9 13.5 13.9 V 13.4 12.3 11.5 12.3 11.5 −14.2 −13.8 −14.2 −13.7 −14 −13.5 −14 V −13.4 −12.4 −11.5 −12.4 −11.5 96 80 96 79 109 90 109 dB 89 118 95 118 94 1012 1012 Common mode 25°C 7.5 7.5 Differential 25°C 2.5 2.5 25°C 80 80 f = 1 MHz Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω 25°C 80 CMRR Full range 79 Supply voltage rejection Supply-voltage ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 82 kSVR Full range 80 Full range is − 40°C to 85°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mV 25 25°C Open-loop output impedance UNIT 2.4 10 zo 26 MAX 5 15 to −10.8 VIC = 0 VIC = 0, See Figure 5 6 TYP 25 Full range 25°C 25 C MIN 2.4 Full range 25°C Input bias current TLE2072AI MAX 9.1 25°C VIC = 0, See Figure 4 TYP 98 80 82 80 pF Ω 98 dB 79 99 Ω 99 dB TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072I electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued) TLE2072I PARAMETER TEST CONDITIONS ICC Supply current (both channels) 0 VO = 0, No load ax Crosstalk attenuation VIC = 0, RL = 2 kΩ IOS Short circuit output current Short-circuit VO = 0 MIN TYP MAX MIN TYP MAX 25°C 2.7 3.1 3.9 2.7 3.1 3.9 Full range 3.9 25°C VID = 1 V 3.9 120 120 −30 −45 −30 −45 30 48 30 48 25°C VID = − 1 V TLE2072AI TA UNIT mA dB mA TLE2072I operating characteristics at specified free-air temperature, VCC ± = ±15 V TLE2072I PARAMETER SR + SR − ts † Positive slew rate TEST CONDITIONS VO(PP) = ± 10 V, AVD = − 1 1, kΩ, RL = 2 kΩ CL = 100 pF, See Figure 1 Negative slew rate Settling time Vn Equivalent input noise voltage VN(PP) Peak-to-peak equivalent input noise voltage AVD = − 1, 10-V step, RL = 1 kΩ, CL = 100 pF TA† MIN TYP 25°C 28 40 Full range 22 25°C 30 Full range 22 To 10 mV TLE2072AI MAX MIN TYP 28 40 MAX V/μs 22 45 30 45 V/μs 22 0.4 0.4 1.5 1.5 μss 25°C To 1 mV f = 10 Hz f = 10 kHz RS = 20 Ω, See Figure 3 25°C f = 0 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT 48 85 48 85 12 17 12 17 6 6 0.6 0.6 nV/√Hz μV V 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 20 V, f = 1 kH kHz, RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 008% 0.008% 0 008% 0.008% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 8 10 8 10 MHz BOM Maximum output outputswing bandwidth VO(PP) = 20 V, RL = 2 kΩ, AVD = − 1, CL = 25 pF 25°C 478 637 478 637 kHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 57° fA /√Hz 57° Full range is − 40°C to 85°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 27 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) TLE2072M PARAMETER TEST CONDITIONS TA† MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω, VO = 0, 0.9 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification ±2.3 3V VO = ±2 RL = 2 kΩ RL = 10 kΩ ri ci Input resistance Input capacitance 0.65 3.5 8 5 to −1 25°C 3.8 Full range 3.6 25°C 3.5 Full range 3.3 25°C 1.5 Full range 1.4 25°C −3.8 Full range −3.6 25°C −3.5 Full range −3.3 25°C −1.5 Full range −1.4 25°C 80 Full range 78 25°C 90 Full range 88 25°C 95 Full range 93 μV/°C 5 100 5 100 pA 20 nA 15 175 15 175 pA 60 nA 5 to −1.9 5 to −1 5 to −1.9 V 5 to −0.8 4.1 3.8 4.1 3.6 3.9 3.5 3.9 V 3.3 2.3 1.5 2.3 1.4 −4.2 −3.8 −4.2 −3.6 −4.1 −3.5 −4.1 V −3.3 −2.4 −1.5 −2.4 −1.4 91 80 91 78 100 90 100 dB 88 106 95 106 93 1012 1012 Common mode 25°C 11 11 Differential 25°C 2.5 2.5 80 80 f = 1 MHz 25°C Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω 25°C CMRR 70 Full range 68 ∗On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. † Full range is − 55°C to 125°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mV 25∗ 25°C Open-loop output impedance UNIT 2.3 60 Full range zo 28 MAX 20 5 to −0.8 VIC = 0 VIC = 0, See Figure 5 6 TYP 25∗ Full range 25°C 25 C MIN 2.3 Full range 25°C Input bias current TLE2072AM MAX 10.5 25°C VIC = 0, See Figure 4 TYP 89 70 68 Ω pF Ω 89 dB TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) (continued) TLE2072M PARAMETER † TEST CONDITIONS kSVR Supply-voltage rejection ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω ICC Supply current (both channels) 0 VO = 0, No load ax Crosstalk attenuation VIC = 0, RL = 2 kΩ IOS Short-circuit output current VO = 0 TA† MIN Full range 80 25°C 2.7 TYP 2.9 TYP MAX 3.6 2.7 25°C UNIT dB 2.9 3.6 25°C VID = − 1 V MIN 80 Full range VID = 1 V TLE2072AM MAX 3.6 3.6 120 120 −35 −35 45 45 mA dB mA Full range is − 55°C to 125°C. TLE2072M operating characteristics at specified free-air temperature, VCC ± = ±5 V TLE2072M PARAMETER TEST CONDITIONS TA† MIN 25°C SR + SR − ts Positive slew rate VO(PP) = ± 2.3 V, AVD = − 1 1, kΩ, RL = 2 kΩ CL = 100 pF, See Figure 1 Negative slew rate Settling time Vn Equivalent input noise voltage VN(PP) Peak-to-peak equivalent input noise voltage Full range AVD = − 1, 2-V step, RL = 1 kΩ, CL = 100 pF To 10 mV MIN TYP MAX To 1 mV f = 10 kHz 25°C f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT 35 18∗ V/μs 18∗ 38 38 18∗ V/μs 18∗ 0.25 0.25 0.4 0.4 μss 25°C f = 10 Hz RS = 20 Ω, See Figure 3 MAX 35 25°C Full range TYP TLE2072AM 48 85∗ 48 85∗ 12 17∗ 12 17∗ 6 nV/√Hz 6 V μV 25°C 06 0.6 06 0.6 In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 5 V, kHz, f = 1 kHz RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 013% 0.013% 0 013% 0.013% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 94 9.4 94 9.4 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 4 V, RL = 2 kΩ , AVD = − 1, CL = 25 pF 25°C 28 2.8 28 2.8 MHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 56° 56° fA /√Hz ∗On † products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. Full range is − 55°C to 125°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 29 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072M electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) TLE2072M PARAMETER TEST CONDITIONS TA† MIN TYP 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω VO = 0, 1.1 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range RS = 50 Ω IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ±10 V RL = 2 kΩ RL = 10 kΩ ri ci Input resistance Input capacitance 15 to −11 Full range 25°C 13.8 Full range 13.6 25°C 13.5 Full range 13.3 25°C 11.5 Full range 11.4 25°C −13.8 Full range −13.6 25°C −13.5 Full range −13.3 25°C −11.5 Full range −11.4 25°C 80 Full range 78 25°C 90 Full range 89 25°C 95 Full range 93 8 μV/°C 6 100 6 100 pA 20 nA 20 175 20 175 pA 60 nA 15 to −11.9 15 to −11 15 to −11.9 V 15 to −10.8 14.1 13.8 14.1 13.6 13.9 13.5 13.9 V 13.3 12.3 11.5 12.3 11.4 −14.2 −13.8 −14.2 −13.6 −14 −13.5 −14 V −13.3 −12.4 −11.5 −12.4 −11.4 96 80 96 78 109 90 109 dB 89 118 95 118 93 1012 Common mode 25°C 7.5 7.5 Differential 25°C 2.5 2.5 25°C 80 80 f = 1 MHz Common mode Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω 25°C 80 CMRR Full range 78 Supply voltage rejection Supply-voltage ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 82 kSVR Full range 80 products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. Full range is − 55°C to 125°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mV 25∗ 1012 Open-loop output impedance UNIT 2.4 25°C zo 30 3.5 60 ∗On † 0.7 20 15 to −10.8 VIC = 0 VIC = 0, See Figure 5 MAX 25∗ Full range 25°C 25 C 6 TYP 2.4 Full range 25°C Input bias current MIN 10.5 25°C VIC = 0, See Figure 4 TLE2072AM MAX 98 80 82 80 pF Ω 98 dB 78 99 Ω 99 dB TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072M electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) TLE2072M PARAMETER † TEST CONDITIONS ICC Supply current (both channels) VO = 0, 0 No load ax Crosstalk attenuation VIC = 0, RL = 2 kΩ IOS Short circuit output Short-circuit current VO = 0 MIN TYP MAX MIN TYP MAX 25°C 2.7 3.1 3.6 2.7 3.1 3.6 Full range 3.6 25°C VID = 1 V 3.6 120 120 −30 −45 −30 −45 30 48 30 48 25°C VID = − 1 V TLE2072AM TA† UNIT mA dB mA Full range is − 55°C to 125°C. TLE2072M operating characteristics at specified free-air temperature, VCC ± = ±15 V TLE2072M PARAMETER SR + TEST CONDITIONS Positive slew rate VO(PP) = 10 V, RL = 2 kΩ, kΩ See Figure 1 SR − Negative slew rate ts Settling time Vn Equivalent input noise voltage VN(PP) Peak-to-peak equivalent input noise voltage AVD = − 1, 10-V step, RL = 1 kΩ, CL = 100 pF AVD = − 1, CL = 100 pF, pF TA† MIN TYP 25°C 28 40 Full range 20 25°C 30 Full range 20 To 10 mV TLE2072AM MAX MIN TYP 28 40 MAX V/μs 20 45 30 45 V/μs 20 0.4 0.4 1.5 1.5 μss 25°C To 1 mV f = 10 Hz f = 10 kHz RS = 20 Ω, See Figure 3 25°C f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT 48 85∗ 48 85∗ 12 17∗ 12 17∗ 6 6 06 0.6 06 0.6 nV/√Hz μV V 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 20 V, f = 1 kH kHz, RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 008% 0.008% 0 008% 0.008% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 8∗ 10 8∗ 10 MHz BOM Maximum output swing output-swing bandwidth VO(PP) = 20 V, RL = 2 kΩ, AVD = − 1, CL = 25 pF 25°C 478∗ 637 478∗ 637 kHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 57° fA /√Hz 57° ∗On † products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. Full range is − 55°C to 125°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 31 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2072Y electrical characteristics at VCC ± = ±15 V, TA = 25°C PARAMETER VIO Input offset voltage IIO Input offset current IIB Input bias current VICR Common-mode Common mode input voltage range VOM + VOM − AVD TEST CONDITIONS VIC = 0, VO = 0, VIC = 0, 0 VO = 0, 0 Maximum M i negative ti peakk output voltage swing Large-signal Large signal differential voltage amplification mV pA 20 175 pA 14.1 IO = − 2 mA 13.5 13.9 IO = − 20 mA 11.5 12.3 IO = 200 μA −13.8 −14.2 IO = 2 mA −13.5 −14 IO = 20 mA −11.5 −12.4 RL = 600 Ω 80 96 RL = 2 kΩ 90 109 RL = 10 kΩ 95 118 Input capacitance VIC = 0, See Figure 5 zo Open-loop output impedance f = 1 MHz CMRR Common-mode rejection ratio VIC = VICRmin, kSVR Supply-voltage rejection ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ±15 V, RS = 50 Ω ICC Supply current (both channels) VO = 0, VO = 0 POST OFFICE BOX 655303 V V V dB Ω 1012 ci 32 6 100 13.8 VIC = 0 Common mode 7.5 Differential 2.5 VO = 0, pF 80 Ω RS = 50 Ω 80 98 dB VO = 0, 82 99 dB No load 2.7 3.1 VID = 1 V −30 −45 30 48 VID = − 1 V • DALLAS, TEXAS 75265 UNIT 6 IO = − 200 μA VO = ± 10 V MAX 1.1 15 to 11.9 Input resistance Short circuit output current Short-circuit See Figure 4 TYP 15 to −11 ri IOS RS = 50 Ω RS = 50 Ω Maximum positive peak output voltage swing TLE2072Y MIN 3.9 mA mA TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLE2074C MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current IIB Input bias current VIC = 0, RS = 50 Ω VO = 0, −1.6 Full range Full range VO = 0, VICR Common-mode Common mode input voltage range VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ±2 ±2.3 3V RL = 2 kΩ RL = 10 kΩ ri † Input resistance VIC = 0 Common mode ci Input capacitance zo Open-loop output impedance f = 1 MHz CMRR Common mode rejection ratio Common-mode VIC = VICRmin, VO = 0, RS = 50 Ω kSVR Supply-voltage Supply voltage rejection ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω Differential 0 VIC = 0, See Figure 5 −0.5 30 15 100 15 100 1400 175 20 5000 Full range 5 to −0.9 25°C 3.8 Full range 3.7 25°C 3.5 Full range 3.4 25°C 1.5 Full range 1.5 25°C −3.8 Full range −3.7 25°C −3.5 Full range −3.4 25°C −1.5 Full range −1.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 5 to −1.9 3.8 4.1 3.9 3.5 3.9 V 3.4 2.3 1.5 2.3 1.5 −4.2 −3.8 −4.2 −3.7 −4.1 −3.5 −4.1 V −3.4 −2.4 −1.5 −2.4 −1.5 91 80 91 79 100 90 100 dB 89 106 95 106 94 1012 25°C 11 11 25°C 2.5 2.5 25°C 80 80 70 68 25°C 82 Full range 80 pA 3.7 1012 25°C pA V 25°C Full range μV/°C 5 to −1.9 5 to −0.9 4.1 mV 175 5000 5 to −1 UNIT 3 10.1 20 5 to −1 MAX 5.1 1400 25°C IO = − 200 μA A 5 TYP 30 Full range RS = 50 Ω MIN 10.1 Full range 25°C 25 C TLE2074AC MAX 7.1 25°C VIC = 0, See Figure 4 TYP 89 70 82 80 pF Ω 89 dB 68 99 Ω 99 dB Full range is 0°C to 70°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 33 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) (continued) PARAMETER ICC IOS † TA† TEST CONDITIONS 25°C Supply current ( four amplifiers ) VO = 0, 0 No load Crosstalk attenuation VIC = 0, RL = 2 kΩ Short-circuit output current VO = 0 TLE2074C TYP MAX MIN TYP MAX 5.2 6.3 7.5 5.2 6.3 7.5 Full range VID = 1 V VID = − 1 V TLE2074AC MIN 7.5 25°C 25°C 7.5 120 120 −35 −35 45 45 UNIT mA dB mA Full range is 0°C to 70°C. TLE2074C operating characteristics at specified free-air temperature, VCC ± = ±5 V PARAMETER TEST CONDITIONS TA† TLE2074C MIN TYP 25°C SR + Positive slew rate SR − Negative slew rate ts † Settling time Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent Peak-to-peak input noise voltage VO(PP) = ± 2.3 V, AVD = − 1 1, RL = 2 kΩ kΩ, CL = 100 pF, See Figure 1 Full range AVD = − 1, 2-V step, RL = 1 kΩ, CL = 100 pF TYP MAX V/μs 22 38 38 22 V/μs 22 To 10 mV 0.25 0.25 0.4 0.4 μss 25°C To 1 mV f = 10 kHz f = 10 Hz to 10 kHz f = 0.1Hz to 10 Hz UNIT 35 22 f = 10 Hz RS = 20 Ω, See Figure 3 MIN 35 25°C Full range TLE2074AC MAX 25°C 48 85 48 85 12 17 12 17 6 6 0.6 0.6 nV/√Hz μV 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 5 V, f = 1 kHz kHz, RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 013% 0.013% 0 013% 0.013% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 94 9.4 94 9.4 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 4 V, RL = 2 kΩ , AVD = − 1, CL = 25 pF 25°C 28 2.8 28 2.8 MHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 56° 56° Full range is 0°C to 70°C. 34 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 fA/√Hz TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLE2074C MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current IIB Input bias current VIC = 0, RS = 50 Ω VO = 0, −1.6 Full range Full range VO = 0, VICR VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ±10 V RL = 2 kΩ RL = 10 kΩ ri ci Input resistance Input capacitance VIC = 0 Common mode VIC = 0, See Figure 5 Differential zo † 30 15 100 15 100 Open-loop output impedance 1400 175 25 Full range 15 to −10.9 25°C 13.8 Full range 13.7 25°C 13.5 Full range 13.4 25°C 11.5 Full range 11.5 25°C −13.8 Full range −13.7 25°C −13.7 Full range −13.6 25°C −11.5 Full range −11.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 15 to −11.9 13.8 14.1 13.9 13.5 13.9 V 13.4 12.3 11.5 12.3 11.5 −14.2 −13.8 −14.2 −13.7 −14 −13.7 −14 V −13.6 −12.4 −11.5 −12.4 −11.5 96 80 96 79 109 90 109 dB 89 118 95 118 94 1012 25°C 7.5 7.5 25°C 2.5 2.5 25°C 80 80 CMRR Common-mode Common mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω Full range 79 Supply voltage rejection ratio Supply-voltage (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 82 kSVR Full range 81 pA 13.7 1012 25°C pA V 25°C f = 1 MHz μV/°C 15 to −11.9 15 to −10.9 14.1 mV 175 5000 15 to −11 UNIT 3 5.1 5000 15 to MAX 10.1 25 −11 IO = − 200 μA A −0.5 1400 25°C RS = 50 Ω 5 TYP 30 Full range Common-mode Common mode input voltage range MIN 10.1 Full range 25°C 25 C TLE2074AC MAX 7.1 25°C VIC = 0, See Figure 4 TYP 98 80 80 82 81 pF Ω 98 dB 79 99 Ω 99 dB Full range is 0°C to 70°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 35 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued) PARAMETER ICC IOS † TA† TEST CONDITIONS 25°C Supply current ( four amplifiers ) 0 VO = 0, No load Crosstalk attenuation VIC = 0, RL = 2 kΩ Short-circuit output current VO = 0 TLE2074C TYP MAX MIN TYP MAX 5.2 6.5 7.5 5.2 6.5 7.5 Full range VID = 1 V VID = − 1 V 7.5 25°C 25°C TLE2074AC MIN 7.5 120 120 −30 −45 −30 −45 30 48 30 48 UNIT mA dB mA Full range is 0°C to 70°C. TLE2074C operating characteristics at specified free-air temperature, VCC ± = ±15 V PARAMETER SR + TEST CONDITIONS Positive slew rate VO(PP) = 10 V, RL = 2 kΩ kΩ, See Figure 1 SR − ts † AVD = − 1, CL = 100 pF, pF Negative slew rate Settling time Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent Peak-to-peak input noise voltage AVD = − 1, 10-V step, RL = 1 kΩ, CL = 100 pF TA† TLE2074C MIN TYP 25°C 25 40 Full range 22 25°C 30 Full range 25 MIN TYP 25 40 MAX 45 30 45 V/μs 25 To 10 mV 0.4 0.4 1.5 1.5 μss 25°C To 1 mV f = 10 kHz f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT V/μs 22 f = 10 Hz RS = 20 Ω, See Figure 3 TLE2074AC MAX 25°C 48 85 48 85 12 17 12 17 6 6 0.6 0.6 nV/√Hz μV 25°C In Equivalent input noise current THD + N VO(PP) = 20 V, Total harmonic distortion kHz, f = 1 kHz plus noise RS = 25 Ω B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 8 10 8 10 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 20 V, RL = 2 kΩ, AVD = − 1, CL = 25 pF 25°C 478 637 478 637 kHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C VIC = 0, f = 10 kHz 25°C 2.8 2.8 AVD = 10, RL = 2 kΩ kΩ, 25°C 0 008% 0.008% 0 008% 0.008% Full range is 0°C to 70°C. 36 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 57° 57° fA/√Hz TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074I electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLE2074I MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω VO = 0, IIB Common-mode Common mode input voltage range IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification ±2.3 3V VO = ±2 RL = 2 kΩ RL = 10 kΩ ri VIC = 0 Common mode ci Input capacitance zo Open-loop output impedance Differential 0 VIC = 0, See Figure 5 f = 1 MHz CMRR Common-mode Common mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω Supply-voltage Supply voltage rejection ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω kSVR † Input resistance MAX −0.5 3 7 Full range 5 to −0.8 25°C 3.8 Full range 3.7 25°C 3.5 Full range 3.4 25°C 1.5 Full range 1.5 25°C −3.8 Full range −3.7 25°C −3.5 Full range −3.4 25°C −1.5 Full range −1.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 30 μV/°C 15 100 15 100 pA 5 nA 20 175 20 175 pA 10 nA 5 to −1.9 5 to −1 5 to −1.9 V 5 to −0.8 4.1 3.8 4.1 3.7 3.9 3.5 3.9 V 3.4 2.3 1.5 2.3 1.5 −4.2 −3.8 −4.2 −3.7 −4.1 −3.5 −4.1 V −3.4 −2.4 −1.5 −2.4 −1.5 91 80 91 79 100 90 100 dB 89 106 95 106 94 25°C 1012 1012 25°C 11 11 25°C 2.5 2.5 25°C 80 80 25°C 70 Full range 68 25°C 82 Full range 80 mV 10.1 10 5 to UNIT 30 5 −1 RS = 50 Ω TYP 10.1 Full range 25°C 25 C VICR 5 Full range 25°C Input bias current −1.6 MIN 9 Full range VO = 0, MAX Full range 25°C VIC = 0, See Figure 4 TLE2074AI TYP 89 70 82 80 pF Ω 89 dB 68 99 Ω 99 dB Full range is − 40°C to 85°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 37 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074I electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) (continued) PARAMETER ICC IOS † TA† TEST CONDITIONS 25°C Supply current ( four amplifiers ) VO = 0, 0 No load Crosstalk attenuation VIC = 0, RL = 2 kΩ Short circuit output current Short-circuit VO = 0 TLE2074I TYP MAX MIN TYP MAX 5.2 6.3 7.5 5.2 6.3 7.5 Full range VID = 1 V VID = − 1 V TLE2074AI MIN 7.5 25°C 25°C 7.5 120 120 −35 −35 45 45 UNIT mA dB mA Full range is − 40°C to 85°C. TLE2074I operating characteristics at specified free-air temperature, VCC ± = ±5 V PARAMETER TEST CONDITIONS TA† TLE2074I MIN TYP 25°C † SR + Positive slew rate SR − Negative slew rate ts Settling time Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent Peak-to-peak input noise voltage VO(PP) = ± 2.3 V, AVD = − 1 1, RL = 2 kΩ kΩ, CL = 100 pF, See Figure 1 Full range AVD = − 1, 2-V step, RL = 1 kΩ, CL = 100 pF TYP MAX V/μs 20 38 38 20 V/μs 20 To 10 mV 0.25 0.25 0.4 0.4 μss 25°C To 1 mV f = 10 kHz f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT 35 20 f = 10 Hz RS = 20 Ω, See Figure 3 MIN 35 25°C Full range TLE2074AI MAX 25°C 48 85 48 85 12 17 12 17 6 6 0.6 0.6 nV/√Hz μV 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 5 V, kHz, f = 1 kHz RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 013% 0.013% 0 013% 0.013% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 94 9.4 94 9.4 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 4 V, RL = 2 kΩ , AVD = − 1, CL = 25 pF 25°C 28 2.8 28 2.8 MHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 56° 56° Full range is − 40°C to 85°C. 38 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 fA/√Hz TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074I electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLE2074I MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω VO = 0, IIB Common-mode Common mode input voltage range IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification VO = ±10 V RL = 2 kΩ RL = 10 kΩ ri ci † Input resistance Input p capacitance VIC = 0 Common mode VIC = 0, See Figure 5 Differential MAX −0.5 3 7 Full range 15 to −10.8 25°C 13.8 Full range 13.7 25°C 13.5 Full range 13.4 25°C 11.5 Full range 11.5 25°C −13.8 Full range −13.7 25°C −13.5 Full range −13.4 25°C −11.5 Full range −11.5 25°C 80 Full range 79 25°C 90 Full range 89 25°C 95 Full range 94 30 μV/°C 15 100 15 100 pA 5 nA 25 175 25 175 pA 10 nA 15 to −11.9 15 to −11 15 to −11.9 V 15 to −10.8 14.1 13.8 14.1 13.7 13.9 13.5 13.9 V 13.4 12.3 11.5 12.3 11.5 −14.2 −13.8 −14.2 −13.7 −14 −13.5 −14 V −13.4 −12.4 −11.5 −12.4 −11.5 96 80 96 79 109 90 109 dB 89 118 95 118 94 25°C 1012 1012 25°C 7.5 7.5 25°C 2.5 2.5 80 80 zo Open-loop output impedance f = 1 MHz 25°C Common-mode Common mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω 25°C 80 CMRR Full range 79 Supply voltage rejection Supply-voltage ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 82 kSVR Full range 80 mV 10.1 10 15 to UNIT 30 5 −11 RS = 50 Ω TYP 10.1 Full range 25°C 25 C VICR 5 Full range 25°C Input bias current −1.6 MIN 9 25°C VO = 0, MAX Full range Full range VIC = 0, See Figure 4 TLE2074AI TYP 98 80 82 80 pF Ω 98 dB 79 99 Ω 99 dB Full range is − 40°C to 85°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 39 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074I electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued) PARAMETER ICC IOS † TA† TEST CONDITIONS 25°C Supply current ( four amplifiers ) 0 VO = 0, No load Crosstalk attenuation VIC = 0, RL = 2 kΩ Short-circuit output current VO = 0 TLE2074I TYP MAX MIN TYP MAX 5.2 6.5 7.5 5.2 6.5 7.5 Full range 7.5 25°C VID = 1 V 25°C VID = − 1 V TLE2074AI MIN 7.5 120 120 −30 −45 −30 −45 30 48 30 48 UNIT mA dB mA Full range is − 40°C to 85°C. TLE2074I operating characteristics at specified free-air temperature, VCC ± = ±15 V PARAMETER SR + Positive slew rate SR − Negative slew rate ts † Settling time Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent Peak-to-peak input noise voltage TA† TEST CONDITIONS VO(PP) = ± 10 V, AVD = − 1 1, RL = 2 kΩ kΩ, CL = 100 pF, See Figure 1 AVD = − 1, 10-V step, RL = 1 kΩ, CL = 100 pF TLE2074I MIN TYP 25°C 25 40 Full range 19 25°C 30 Full range 22 MIN TYP 25 40 MAX 45 30 45 V/μs 22 To 10 mV 0.4 0.4 1.5 1.5 μss 25°C To 1 mV 25°C f = 10 kHz f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT V/μs 19 f = 10 Hz RS = 20 Ω, See Figure 3 TLE2074AI MAX 48 85 48 85 12 17 12 17 6 6 0.6 0.6 nV/√Hz μV 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 20 V, f = 1 kHz, kHz RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 008% 0.008% 0 008% 0.008% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 8 10 8 10 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 20 V, RL = 2 kΩ, AVD = − 1, CL = 25 pF 25°C 478 637 478 637 kHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C Full range is − 40°C to 85°C. 40 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 57° 57° fA/√Hz TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLE2074M MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50Ω VO = 0, −1.6 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA IO = 200 μA A VOM − Maximum negative peak output voltage swing IO = 2 mA IO = 20 mA RL = 600 Ω AVD Large signal differential Large-signal voltage amplification ±2.3 3V VO = ±2 RL = 2 kΩ RL = 10 kΩ ri ‡ VIC = 0 Common mode ci Input capacitance zo Open-loop output impedance Differential 0 VIC = 0, See Figure 5 f = 1 MHz CMRR Common-mode Common mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω Supply-voltage Supply voltage rejection ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω kSVR † Input resistance −0.5 Full range 5 to −0.8 25°C 3.8 Full range 3.6 25°C 3.5 Full range 3.3 25°C 1.5 Full range 1.4 25°C −3.8 Full range −3.6 25°C −3.5 Full range −3.3 25°C −1.5 Full range −1.4 25°C 80 Full range 78 25°C 90 Full range 88 25°C 95 Full range 93 15 100 15 100 pA 20 nA 20 175 20 175 pA 60 nA 5 to −1.9 5 to −1 5 to −1.9 V 5 to −0.8 4.1 3.8 4.1 3.6 3.9 3.5 3.9 V 3.3 2.3 1.5 2.3 1.4 −4.2 −3.8 −4.2 −3.6 −4.1 −3.5 −4.1 V −3.3 −2.4 −1.5 −2.4 −1.4 91 80 91 78 100 90 100 dB 88 106 95 106 93 1012 25°C 11 11 25°C 2.5 2.5 25°C 80 80 70 68 25°C 82 Full range 80 mV μV/°C 1012 25°C 3 30} 25°C Full range UNIT 10.1 60 5 to MAX 8.5 20 −1 RS = 50 Ω 5 TYP 30} Full range 25°C 25 C MIN 10.1 Full range 25°C Input bias current TLE2074AM MAX 10.5 25°C VIC = 0, See Figure 4 TYP 89 70 82 80 pF Ω 89 dB 68 99 Ω 99 dB Full range is − 55°C to 125°C. On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 41 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) (continued) PARAMETER ICC IOS † TEST CONDITIONS TA† TLE2074M TYP MAX MIN TYP MAX 5.2 6.3 7.5 5.2 6.3 7.5 25°C Supply current ( four amplifiers ) 0 VO = 0, No load Crosstalk attenuation VIC = 0, RL = 2 kΩ Short circuit output current Short-circuit VO = 0 VID = 1 V VID = − 1 V TLE2074AM MIN Full range 7.5 25°C 7.5 120 120 −35 −35 45 45 25°C UNIT mA dB mA Full range is − 55°C to 125°C. TLE2074M operating characteristics at specified free-air temperature, VCC ± = ±5 V PARAMETER TEST CONDITIONS TA† TLE2074M MIN TYP 25°C † ‡ SR + Positive slew rate SR − Negative slew rate ts Settling time Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent Peak-to-peak input p noise voltage g VO(PP) = ± 2.3 V, AVD = − 1 1, RL = 2 kΩ kΩ, CL = 100 pF, See Figure 1 Full range AVD = − 1, 2-V step, RL = 1 kΩ, CL = 100 pF TYP MAX V/μs 18} 38 38 18} V/μs 18} To 10 mV 0.25 0.25 0.4 0.4 μss 25°C To 1 mV f = 10 kHz 25°C f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT 35 18} f = 10 Hz RS = 20 Ω, See Figure 3 MIN 35 25°C Full range TLE2074AM MAX 48 85} 48 85} 12 17} 12 17} 6 6 06 0.6 06 0.6 nV/√Hz μV V 25°C In Equivalent input noise current VIC = 0, f = 10 kHz 25°C 2.8 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 5 V, f = 1 kHz, kHz RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 013% 0.013% 0 013% 0.013% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 94 9.4 94 9.4 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 4 V, RL = 2 kΩ, AVD = − 1, CL = 25 pF 25°C 28 2.8 28 2.8 MHz fm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 56° 56° Full range is − 55°C to 125°C. On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. 42 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 fA/√Hz TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074M electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLE2074M MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current VIC = 0, RS = 50 Ω VO = 0, −1.6 Full range Full range IIB VO = 0, VICR Common-mode Common mode input voltage range IO = − 200 μA A VOM + Maximum positive peak output voltage swing IO = − 2 mA IO = − 20 mA VOM − Maximum negative peak output voltage swing IO = 2 mA Full range 25°C 13.8 Full range 13.6 25°C 13.5 Full range 13.3 25°C 11.5 Full range 11.4 RL = 600 Ω Large signal differential Large-signal voltage amplification VO = ±10 V RL = 2 kΩ RL = 10 kΩ ri † ‡ Input resistance VIC = 0 Common mode ci Input capacitance zo Open-loop output impedance f = 1 MHz CMRR Common mode rejection ratio Common-mode VIC = VICRmin, VO = 0, RS = 50 Ω kSVR Supply-voltage Supply voltage rejection ratio (ΔVCC± /ΔVIO) VCC ± = ± 5 V to ± 15 V, VO = 0, RS = 50 Ω Differential 15 100 15 100 pA 20 nA 25 175 25 175 pA 60 nA 0 VIC = 0, See Figure 5 15 to −11.9 15 to −11 15 to −11.9 V 15 to −10.8 14.1 13.8 14.1 13.6 13.9 13.5 13.9 V 13.3 12.3 11.5 12.3 11.4 −13.6 −13.6 25°C −13.5 Full range −13.3 −13.3 −11.5 −12.4 −11.5 −12.4 −11.4 −11.4 80 Full range 78 25°C 90 Full range 88 25°C 95 Full range 93 −14 96 −13.5 80 −14 V 96 78 109 90 109 dB 88 118 95 118 93 25°C 1012 1012 25°C 7.5 7.5 25°C 2.5 2.5 25°C 80 80 25°C 80 Full range 78 25°C 82 Full range 80 mV μV/°C Full range 25°C 3 30} −13.8 −14.2 Full range UNIT 10.1 −13.8 −14.2 25°C IO = 20 mA AVD 15 to MAX 8.5 60 15 to −10.8 25°C IO = 200 μA A −0.5 20 −11 RS = 50 Ω 5 TYP 30} Full range 25°C 25 C MIN 10.1 Full range 25°C Input bias current TLE2074AM MAX 10.5 25°C VIC = 0, See Figure 4 TYP 98 80 82 80 pF Ω 98 dB 78 99 Ω 99 dB Full range is − 55°C to 125°C. On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 43 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074M electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued) PARAMETER ICC IOS † TEST CONDITIONS TA† 25°C Supply current ( four amplifiers ) 0 VO = 0, No load Crosstalk attenuation VIC = 0, RL = 2 kΩ Short circuit output current Short-circuit VO = 0 VID = 1 V VID = − 1 V TLE2074M TYP MAX MIN TYP MAX 5.2 6.5 7.5 5.2 6.5 7.5 Full range 7.5 25°C 25°C TLE2074AM MIN 7.5 120 120 −30 −45 −30 −45 30 48 30 48 UNIT mA dB mA Full range is − 55°C to 125°C. TLE2074M operating characteristics at specified free-air temperature, VCC ± = ±15 V PARAMETER SR + TEST CONDITIONS Positive slew rate VO(PP) = 10 V, RL = 2 kΩ kΩ, See Figure 1 SR − ts † ‡ AVD = − 1, CL = 100 pF, pF Negative slew rate Settling time Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent Peak-to-peak input p noise voltage g AVD = − 1, 10 V step, 10-V RL = 1 kΩ, CL = 100 pF TA† TLE2074M MIN TYP 25°C 25 40 Full range 17 25°C 30 Full range 20 MIN TYP 25 40 MAX 45 30 45 V/μs 20 To 10 mV 0.4 0.4 1.5 1.5 μss 25°C To 1 mV f = 10 kHz 25°C f = 10 Hz to 10 kHz f = 0.1 Hz to 10 Hz UNIT V/μs 17 f = 10 Hz RS = 20 Ω, See Figure g 3 TLE2074AM MAX 48 85} 48 85} 12 17} 12 17} 6 6 06 0.6 06 0.6 nV/√Hz μV V 25°C In Equivalent input noise current 0, VIC = 0 f = 10 kHz 25°C 28 2.8 28 2.8 THD + N Total harmonic distortion plus noise VO(PP) = 20 V, f = 1 kH kHz, RS = 25 Ω AVD = 10, RL = 2 kΩ kΩ, 25°C 0 008% 0.008% 0 008% 0.008% B1 Unity gain bandwidth Unity-gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C 8} 10 8} 10 MHz BOM Maximum output-swing output swing bandwidth VO(PP) = 20 V, RL = 2 kΩ, AVD = − 1, CL = 25 pF 25°C 478} 637 478} 637 kHz φm Phase margin at unity gain VI = 10 mV, CL = 25 pF, RL = 2 kΩ, See Figure 2 25°C Full range is − 55°C to 125°C. On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. 44 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 57° 57° fA/√Hz TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TLE2074Y electrical characteristics at VCC ± = ±15 V, TA = 25°C (unless otherwise noted) PARAMETER VIC = 0, RS = 50 Ω VO = 0, VIC = 0, See Figure 4 VO = 0, Input bias current Common-mode Common mode input voltage range RS = 50 Ω VIO Input offset voltage IIO Input offset current IIB VICR VOM + VOM − AVD ri TEST CONDITIONS Maximum positive peak output voltage swing Maximum negative peak output voltage swing Large-signal Large signal differential voltage amplification Input resistance TLE2074Y MIN 15 100 pA 25 175 pA IO = − 200 μA 13.8 14.1 IO = − 2 mA 13.5 13.9 IO = − 20 mA 11.5 12.3 IO = 200 μA −13.8 −14.2 IO = 2 mA −13.5 −14 IO = 20 mA −11.5 −12.4 RL = 600 Ω 80 96 RL = 2 kΩ 90 109 RL = 10 kΩ 95 118 V V V dB Ω 1012 Common mode UNIT mV 15 to 11.9 VO = ± 10 V MAX 5 15 to −11 VIC = 0 7.5 ci Input capacitance zo Open-loop output impedance f = 1 MHz CMRR Common-mode rejection ratio VIC = VICRmin, RS = 50 Ω kSVR Supply-voltage rejection ratio (ΔVCC± /ΔVIO) ICC IOS Differential TYP 0 VO = 0, See Figure 5 pF 2.5 80 Ω 80 98 dB VCC ± = ± 5 V to ±15 V, VO = 0, RS = 50 Ω 82 99 dB Supply current ( four amplifiers ) VO = 0, No load 5.2 6.5 −45 VO = 0 VID = 1 V −30 Short circuit output current Short-circuit 30 48 POST OFFICE BOX 655303 VO = 0, VID = − 1 V • DALLAS, TEXAS 75265 7.5 mA mA 45 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 PARAMETER MEASUREMENT INFORMATION 2 kΩ 10 kΩ VCC + VCC + 2 kΩ VI − + VO 100 Ω VI − + VCC + VCC + RL † RL CL† † Includes fixture capacitance Figure 1. Slew-Rate Test Circuit 46 VO POST OFFICE BOX 655303 CL† Includes fixture capacitance Figure 2. Unity-Gain Bandwidth and Phase-Margin Test Circuit • DALLAS, TEXAS 75265 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 PARAMETER MEASUREMENT INFORMATION 2 kΩ VCC + Ground Shield − + RS RS VCC + − + VO VO VCC − Picoammeters VCC − Figure 3. Noise-Voltage Test Circuit Figure 4. Input-Bias and OffsetCurrent Test Circuit VCC + IN − IN + Cic − + Cid Cic VO VCC − Figure 5. Internal Input Capacitance typical values Typical values presented in this data sheet represent the median (50% point) of device parametric performance. input bias and offset current At the picoampere bias current level typical of the TLE207x and TLE207xA, accurate measurement of the bias current becomes difficult. Not only does this measurement require a picoammeter but test socket leakages can easily exceed the actual device bias currents. To accurately measure these small currents, Texas Instruments uses a two-step process. The socket leakage is measured using picoammeters with bias voltages applied but with no device in the socket. The device is then inserted in the socket and a second test is performed that measures both the socket leakage and the device input bias current. The two measurements are then subtracted algebraically to determine the bias current of the device. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 47 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO Input offset voltage Distribution 6, 7, 8 αVIO Temperature coefficient of input offset voltage Distribution 9, 10, 11 IIO Input offset current vs Free-air temperature 12, 13 IIB Input bias current vs Free-air temperature vs Total supply voltage 12, 13 14 VICR Common-mode input voltage range vs Free-air temperature VO Output voltage vs Differential input voltage VOM + Maximum positive peak output voltage vs Output current VOM − Maximum negative peak output voltage vs Output current VOM Maximum peak output voltage vs Free-air temperature vs Supply voltage VO(PP) Maximum peak-to-peak output voltage vs Frequency 23 VO Output voltage vs Settling time 24 AVD Large-signal differential voltage amplification vs Load resistance vs Free-air temperature 25 26, 27 AVD Small-signal differential voltage amplification vs Frequency 28, 29 CMRR Common-mode rejection ratio vs Frequency vs Free-air temperature 30 31 kSVR Supply-voltage rejection ratio vs Frequency vs Free-air temperature 32 33 ICC Supply current vs Supply voltage vs Free-air temperature vs Differential input voltage IOS Short-circuit output current vs Supply voltage vs Elapsed time vs Free-air temperature SR Slew rate vs Free-air temperature vs Load resistance vs Differential input voltage Vn Equivalent Input noise voltage (spectral density) vs Frequency 53 Input referred noise voltage vs Noise bandwidth Over a 10-second time interval 54 55 Vn 18 19 20, 21 22 34, 35, 36 37, 38, 39 40 − 45 46 47 48 49, 50 51 52 Third-octave spectral noise density vs Frequency bands THD + N Total harmonic distortion plus noise vs Frequency B1 Unity-gain bandwidth vs Load capacitance 59 Gain-bandwidth product vs Free-air temperature vs Supply voltage 60 61 Gain margin vs Load capacitance 62 Phase margin vs Free-air temperature vs Supply voltage vs Load capacitance 63 64 65 Phase shift vs Frequency Noninverting large-signal pulse response vs Time 66 Small-signal pulse response vs Time 67 Closed-loop output impedance vs Frequency 68 Crosstalk attenuation vs Frequency 69 φm zo 48 15 16, 17 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 56 57, 58 28, 29 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLE2072 INPUT OFFSET VOLTAGE DISTRIBUTION OF TLE2071 INPUT OFFSET VOLTAGE 30 27 20 VCC = ± 15 V TA = 25°C P Package 18 16 Percentage of Units − % Percentage of Units − % 24 21 18 15 12 9 14 12 10 8 6 4 6 2 3 0 −4 600 Units Tested From One Wafer Lot VCC = ± 15 V TA = 25°C P Package − 2.4 − 0.8 0.8 2.4 0 −4 4 − 2.4 VIO − Input Offset Voltage − mV Figure 6 45 30 VCC = ± 15 V TA = 25°C N Package VCC = ± 15 V TA = − 55°C to 125°C P Package 27 Percentage of Amplifiers − % Percentage of Units − % 4 DISTRIBUTION OF TLE2071 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT 40 35 30 25 20 15 10 5 0 −8 2.4 0.8 Figure 7 DISTRIBUTION OF TLE2074 INPUT OFFSET VOLTAGE 50 − 0.8 VIO V IO − Input Offset Voltage − mV 24 21 18 15 12 9 6 3 − 4.8 − 1.6 1.6 4.8 8 VIO V IO − Input Offset Voltage − mV 0 − 40 − 32 − 24 −16 − 8 0 8 16 24 32 40 αVIO − Temperature Coefficient − μV/°C Figure 9 Figure 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 49 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLE2074 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT DISTRIBUTION OF TLE2072 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT 27 Percentage of Amplifiers − % 24 30 310 Amplifiers VCC = ± 15 V TA = − 55°C to 125°C P Package 27 Percentage of Amplifiers − % 30 21 18 15 12 9 6 VCC = ± 15 V TA = − 55°C to 125°C N Package 24 21 18 15 12 9 6 3 3 0 − 30 − 24 −18 −12 − 6 0 6 12 18 24 0 − 40 − 32 − 24 −16 − 8 30 100 VCC ± = ± 5 V VIC = 0 VO = 0 1 IIB IIO 0.1 0.01 45 40 65 85 105 125 10 VCC ± = ± 15 V VIC = 0 VO = 0 IIB 1 0.1 IIO 0.01 0.001 −75 −55 −35 −15 5 25 45 65 85 105 125 TA − Free-Air Temperature − °C Figure 12 50 32 100 TA − Free-Air Temperature − °C † 24 INPUT BIAS CURRENT AND INPUT OFFSET CURRENT† vs FREE-AIR TEMPERATURE I IO − Input Bias and Offset Currents − nA IIIB IB and IIO I IO − Input Bias and Offset Currents − nA IIIB IB and IIO INPUT BIAS CURRENT AND INPUT OFFSET CURRENT† vs FREE-AIR TEMPERATURE 25 16 Figure 11 Figure 10 0.001 −75 −55 −35 −15 −5 8 αVIO − Temperature Coefficient − μV/°C αVIO − Temperature Coefficient − μV/°C 10 0 Figure 13 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS COMMON-MODE INPUT VOLTAGE RANGE† vs FREE-AIR TEMPERATURE INPUT BIAS CURRENT vs TOTAL SUPPLY VOLTAGE 10 6 VCC + + 0.5 IIIB IB − Input Bias Current − pA 10 5 VVIC ICR − Common-Mode Input Voltage Range − V VICmax = VCC + TA = 125°C VICmin 10 4 10 3 10 2 TA = 25°C 10 1 TA = − 55°C 10 0 0 5 10 15 20 25 30 35 40 45 RS = 50 Ω VCC + VICmax VCC + − 0.5 VCC − + 3.5 VICmin VCC − + 3 VCC − + 2.5 VCC − + 2 − 75 −55 −35 −15 Figure 14 RL = 600 Ω 100 RL = 2 kΩ RL = 10 kΩ 0 RL = 10 kΩ − 100 RL = 2 kΩ − 200 − 400 −5 −4 85 105 12 − 2 − 10 200 RL = 600 Ω RL = 2 kΩ 100 0 RL = 10 kΩ RL = 10 kΩ − 100 RL = 2 kΩ − 200 RL = 600 Ω RL = 600 Ω −3 VCC ± = ± 15 V VIC = 0 RS = 50 Ω TA = 25°C 300 VO − Output voltage − V VO VO − Output voltage − V VO 65 400 VCC ± = ± 5 V VIC = 0 RS = 50 Ω TA = 25°C − 300 − 300 0 1 2 3 4 5 VID − Differential Input Voltage − μV − 400 − 15 − 10 −5 0 5 10 15 VID − Differential Input Voltage − μV Figure 16 † 45 OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE 400 200 25 Figure 15 OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE 300 5 TA − Free-Air Temperature − °C VCC − Total Supply Voltage (referred to VCC − ) − V Figure 17 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 51 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS 15 13.5 12 TA = − 55°C 10.5 9 7.5 TA = 25°C 6 TA = 125°C 4.5 TA = 85°C 3 1.5 VCC ± = ± 15 V 0 0 − 5 −10 −15 − 20 − 25 − 30 − 35 − 40 − 45 − 50 MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE† vs OUTPUT CURRENT V OM − − Maximum Negative Peak Output Voltage − V VVOM OM+ − Maximum Positive Peak Output Voltage − V MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE† vs OUTPUT CURRENT −15 −13.5 TA = − 55°C −12 −10.5 TA = 25°C −9 −7.5 −6 TA = 85°C − 4.5 TA = 125°C −3 −1.5 VCC ± = ± 15 V 0 0 5 IO − Output Current − mA 10 15 Figure 18 | V OM| − Maximum Peak Output Voltage − V VOM − Maximum Peak Output Voltage − V V OM IO = − 2 mA 3 IO = − 20 mA 1 0 VCC ± = ± 5 V −1 IO = 20 mA −2 −3 IO = 2 mA −4 −5 −75 −55 −35 −15 IO = 200 μA 5 25 45 40 45 50 65 85 105 125 14 IO = 2 mA 13.5 IO = − 2 mA 13 IO = 20 mA 12.5 IO = − 20 mA 12 11.5 11 10.5 VCC ± = ± 15 V 10 −75 −55 −35 −15 5 25 45 65 85 105 125 TA − Free-Air Temperature − °C Figure 20 52 35 IO = 200 μA IO = − 200 μA 14.5 TA − Free-Air Temperature − °C † 30 MAXIMUM PEAK OUTPUT VOLTAGE† vs FREE-AIR TEMPERATURE 15 IO = − 200 μA 4 2 25 Figure 19 MAXIMUM PEAK OUTPUT VOLTAGE† vs FREE-AIR TEMPERATURE 5 20 IO − Output Current − mA Figure 21 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE† vs FREQUENCY 25 VOM VOM − Maximum Peak Output Voltage − V TA = 25°C 20 IO = − 200 μA 15 IO = − 2 mA 10 5 IO = − 20 mA 0 IO = 20 mA −5 −10 IO = 2 mA IO = 200 μA −15 − 20 − 25 0 2.5 5 10 12.5 15 17.5 20 22.5 25 7.5 V VO(PP) O(PP) − Maximum Peak-to-Peak Output Voltage − V MAXIMUM PEAK OUTPUT VOLTAGE vs SUPPLY VOLTAGE 30 VCC ± = ± 15 V 25 20 TA = − 55°C 15 10 TA = 25°C, 125°C VCC ± = ± 5 V 5 TA = − 55°C 0 100 k 1M f − Frequency − Hz |VCC ± | − Supply Voltage − V Figure 22 10 M Figure 23 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs LOAD RESISTANCE OUTPUT VOLTAGE vs SETTLING TIME 125 12.5 10 10 mV 120 AVD A VD − Large-Signal Differential Voltage Amplification − dB 1 mV 7.5 VO VO − Output Voltage − V RL = 2 kΩ TA = 25°C, 125°C 5 2.5 VCC ± = ± 15 V RL = 1 kΩ CL = 100 pF AV = − 1 TA = 25°C Rising 0 Falling − 2.5 −5 1 mV − 7.5 10 mV VIC = 0 RS = 50 Ω TA = 25°C 115 110 VCC ± = ± 15 V 105 VCC ± = ± 5 V 100 95 − 10 − 12.5 0 0.5 1 1.5 2 90 0.1 ts − Settling Time − μs 10 100 RL − Load Resistance − kΩ Figure 25 Figure 24 † 1 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 53 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION† vs FREE-AIR TEMPERATURE 110 AVD A VD − Large-Signal Differential Voltage Amplification − dB 107 RL = 10 kΩ 104 101 RL = 2 kΩ 98 95 92 RL = 600 Ω 89 86 83 VCC ± = ± 5 V VO = ± 2.3 V 80 −75 − 55 − 35 −15 5 25 45 65 85 105 125 TA − Free-Air Temperature − °C Figure 26 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION† vs FREE-AIR TEMPERATURE 125 AVD A VD − Large-Signal Differential Voltage Amplification − dB 121 VCC ± = ± 15 V VO = ± 10 V RL = 10 kΩ 117 113 RL = 2 kΩ 109 105 101 97 RL = 600 Ω 93 89 85 −75 − 55 − 35 −15 5 25 45 65 85 105 125 TA − Free-Air Temperature − °C Figure 27 † 54 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS SMALL-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY 140 0° VCC ± = ± 15 V RL = 2 kΩ CL = 100 pF TA = 25°C Gain 100 20° 40° 80 60° Phase Shift 60 80° 40 100° 20 120° 0 140° − 20 160° Phase Shift AAVD VD − Small-Signal Differential Voltage Amplification − dB 120 180° − 40 1 10 100 1k 10 k 100 k 1 M 10 M 100 M f − Frequency − Hz Figure 28 SMALL-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY 30 80° Phase Shift 100° CL = 25 pF 10 120° Gain 0 140° Phase Shift AAVD VD − Small-Signal Differential Voltage Amplification − dB CL = 100 pF 20 CL = 100 pF VCC ± = ± 15 V VIC = 0 RL = 2 kΩ TA = 25°C − 10 CL = 25 pF 160° − 20 1 4 10 40 180° 100 f − Frequency − MHz Figure 29 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 55 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS COMMON-MODE REJECTION RATIO† vs FREE-AIR TEMPERATURE COMMON-MODE REJECTION RATIO vs FREQUENCY 100 CMRR − Common-Mode Rejection Ratio − dB CMRR − Common-Mode Rejection Ratio − dB 100 VCC ± = ± 15 V 90 80 VCC ± = ± 5 V 70 60 50 40 30 VIC = 0 VO = 0 RS = 50 Ω TA = 25°C 20 10 100 1k 10 k 100 k 1M VCC ± = ± 15 V 94 91 88 VCC ± = ± 5 V 85 82 79 76 73 VIC = VICRmin VO = 0 RS = 50 Ω 70 −75 − 55 − 35 −15 0 10 97 10 M Figure 30 kXXXX SVR − Supply-Voltage Rejection Ratio − dB kXXXX SVR − Supply-Voltage Rejection Ratio − dB kSVR + 80 60 kSVR − 40 Δ VCC ± = ± 5 V to ± 15 V VIC = 0 VO = 0 RS = 50 Ω TA = 25°C 100 1k 10 k 100 k 1M 10 M 114 kSVR + 102 96 90 kSVR − 84 78 72 66 Δ VCC ± = ± 5 V to ± 15 V VIC = 0 VO = 0 RS = 50 Ω 60 −75 − 55 − 35 −15 5 25 45 65 85 105 125 TA − Free-Air Temperature − °C Figure 32 56 85 105 125 108 f − Frequency − Hz † 65 120 100 − 20 10 45 SUPPLY-VOLTAGE REJECTION RATIO† vs FREE-AIR TEMPERATURE 120 0 25 Figure 31 SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY 20 5 TA − Free-Air Temperature − °C f − Frequency − Hz Figure 33 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS TLE2072 SUPPLY CURRENT vs SUPPLY VOLTAGE TLE2071 SUPPLY CURRENT vs SUPPLY VOLTAGE 4 4 VIC = 0 VO = 0 No Load 3.6 3.6 2.8 IICC CC − Supply Current − mA 3.2 IICC CC − Supply Current − mA VIC = 0 VO = 0 No Load 3.8 TA = 25°C 2.4 TA = 125°C 2 1.6 TA = − 55°C 1.2 3.4 TA = 125°C 3.2 3 TA = 25°C 2.8 2.6 0.8 2.4 0.4 2.2 TA = − 55°C 2 0 0 2 4 6 8 10 12 14 16 18 0 20 2.5 5 10 12.5 15 17.5 20 22.5 25 |VCC ±| − Supply Voltage − V |VCC ±| − Supply Voltage − V Figure 35 Figure 34 TLE2071 SUPPLY CURRENT† vs FREE-AIR TEMPERATURE TLE2074 SUPPLY CURRENT vs SUPPLY VOLTAGE 4 10 VIC = 0 VO = 0 No Load 3.6 TA = 125°C 6 TA = 25°C TA = − 55°C VIC = 0 VO = 0 No Load 3.2 IICC CC − Supply Current − mA 8 IICC CC − Supply Current − mA 7.5 4 2.8 2.4 VCC ± = ± 15 V 2 1.6 VCC ± = ± 5 V 1.2 0.8 2 0.4 0 0 2 4 6 8 10 12 14 16 18 20 0 −75 − 55 − 35 −15 25 45 65 85 105 125 TA − Free-Air Temperature − °C |VCC ±| − Supply Voltage − V Figure 36 † 5 Figure 37 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 57 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS TLE2072 SUPPLY CURRENT† vs FREE-AIR TEMPERATURE TLE2074 SUPPLY CURRENT† vs FREE-AIR TEMPERATURE 10 3.5 3.4 VIC = 0 VO = 0 No Load VIC = 0 VO = 0 No Load 9 3.2 IICC CC − Supply Current − mA IICC CC − Supply Current − mA 3.3 VCC ± = ± 15 V 3.1 3 VCC ± = ± 5 V 2.9 2.8 8 7 VCC ± = ± 15 V VCC ± = ± 5 V 6 2.7 2.6 2.5 −75 −55 −35 −15 5 25 45 65 5 − 75 − 55 − 35 − 15 85 105 125 TA − Free-Air Temperature − °C 85 105 125 14 VCC + = 5 V VCC − = 0 VIC = 4.5 V TA = 25°C Open Loop No Load 8 VCC + = 5 V VCC − = 0 VIC = 4.5 V TA = 25°C Open Loop No Load 12 IICC CC − Supply Current − mA 10 IICC CC − Supply Current − mA 65 TLE2072 SUPPLY CURRENT vs DIFFERENTIAL INPUT VOLTAGE 12 6 4 2 10 8 6 4 2 − 0.25 0 0.25 0.5 0 − 0.5 VID − Differential Input Voltage − V − 0.25 0 0.25 VID − Differential Input Voltage − V Figure 41 Figure 40 58 45 Figure 39 TLE2071 SUPPLY CURRENT vs DIFFERENTIAL INPUT VOLTAGE † 25 TA − Free-Air Temperature − °C Figure 38 0 − 0.5 5 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 0.5 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS TLE2071 SUPPLY CURRENT vs DIFFERENTIAL INPUT VOLTAGE TLE2074 SUPPLY CURRENT vs DIFFERENTIAL INPUT VOLTAGE 25 20 VCC + = 5 V VCC − = 0 VIC = 4.5 V TA = 25°C Open Loop No Load IICC CC − Supply Current − mA 16 14 20 12 10 8 6 18 15 13 10 8 4 5 2 3 0 − 0.5 − 0.25 0 0.25 VID − Differential Input Voltage − V VCC ± = ± 15 V VIC = 0 TA = 25°C Open Loop No Load 23 IICC CC − Supply Current − mA 18 0 −1.5 0.5 − 0.9 Figure 42 0.3 0 0.9 1.5 Figure 43 TLE2074 SUPPLY CURRENT vs DIFFERENTIAL INPUT VOLTAGE TLE2072 SUPPLY CURRENT vs DIFFERENTIAL INPUT VOLTAGE 40 25 15 10 VCC ± = ± 15 V VIC = 0 TA = 25°C Open Loop No Load 36 32 IICC CC − Supply Current − mA VCC ± = ± 15 V VIC = 0 TA = 25°C Open Loop No Load 20 IICC CC − Supply Current − mA − 0.3 VID − Differential Input Voltage − V 28 24 20 16 12 8 5 4 0 −1.5 −1 − 0.5 0 0.5 1 1.5 VID − Differential Input Voltage − V 0 −1.5 −1.2 − 0.9 − 0.6 − 0.3 0 0.3 0.6 0.9 1.2 1.5 VID − Differential Input Voltage − V Figure 44 Figure 45 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 59 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS SHORT-CIRCUIT OUTPUT CURRENT vs ELAPSED TIME 60 50 48 40 VID = − 1 V 36 24 12 VO = 0 TA = 25°C 0 −12 − 24 VID = 1 V − 36 − 48 IIOS OS − Short-Circuit Output Current − mA IIOS OS − Short-Circuit Output Current − mA SHORT-CIRCUIT OUTPUT CURRENT vs SUPPLY VOLTAGE VID = − 1 V 30 20 10 VCC ± = ± 15 V VO = 0 TA = 25°C 0 −10 − 20 − 30 VID = 1 V − 40 − 50 − 60 0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 25 0 60 Figure 46 Figure 47 SHORT-CIRCUIT OUTPUT CURRENT† vs FREE-AIR TEMPERATURE SLEW RATE† vs FREE-AIR TEMPERATURE 45 43 VID = − 1 V VCC ± = ± 15 V 48 32 VCC ± = ± 5 V 0 − 16 VCC ± = ± 5 V VID = 1 V − 32 VCC ± = ± 15 V − 48 − 64 41 SR − Slew Rate − V/xs V/μ s IIOS OS − Short-Circuit Output Current − mA 80 16 VCC ± = ± 15 V RL = 2 kΩ CL = 100 pF 39 37 35 SR + 33 31 29 5 25 45 65 85 105 125 25 −75 − 55 − 35 −15 TA − Free-Air Temperature − °C 5 25 45 65 85 105 125 TA − Free-Air Temperature − °C Figure 48 60 SR − 27 VO = 0 − 80 −75 − 55 − 35 −15 † 180 t − Elapsed Time − s |VCC ± | − Supply Voltage − V 64 120 Figure 49 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS SLEW RATE† vs FREE-AIR TEMPERATURE SLEW RATE vs LOAD RESISTANCE 50 70 SR − Slew Rate − V/μ s 62 VCC ± = ± 15 V RL = 2 kΩ CL = 100 pF Rising Edge 40 30 SR − Slew Rate − V/μ s 66 58 54 50 SR − 46 SR + 42 20 VCC ± = ± 5 V VO ± = ± 2.5 V 10 0 −10 AV = − 1 CL = 100 pF TA = 25°C − 20 38 − 30 34 − 40 30 −75 − 55 − 35 −15 Falling Edge − 50 100 1k 5 25 45 65 85 105 125 TA − Free-Air Temperature − °C EQUIVALENT INPUT NOISE VOLTAGE (SPECTRAL DENSITY) vs FREQUENCY 50 Hz AV = − 1 SR − Slew Rate − V/μ s V n − Equivalent Input Noise Voltage − nV/ Vn 40 AV = 1 Rising Edge 20 VCC ± = ± 15 V VO ± = ± 10 V (10% − 90%) CL = 100 pF TA = 25°C 10 0 −10 − 20 − 30 Falling Edge AV = − 1 − 40 − 50 0.1 AV = 1 0.4 1 4 10 45 40 VCC ± = ± 15 V VIC = 0 RS = 20 Ω TA = 25°C 35 30 25 20 15 10 5 0 10 100 1k 10 k f − Frequency − Hz VID − Differential Input Voltage − V Figure 52 † 100 k Figure 51 SLEW RATE vs DIFFERENTIAL INPUT VOLTAGE 30 10 k RL − Load Resistance − Ω Figure 50 50 VCC ± = ± 15 V VO ± = ± 10 V Figure 53 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 61 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS INPUT-REFERRED NOISE VOLTAGE vs NOISE BANDWIDTH 1.2 VCC ± = ± 15 V VIC = 0 RS = 20 Ω TA = 25°C 10 Vn − Input-Referred Noise Voltage − μV Vn Vn − Input-Referred Noise Voltage − μV Vn 100 INPUT-REFERRED NOISE VOLTAGE OVER A 10-SECOND TIME INTERVAL Peak-to-Peak 1 RMS 0.1 0.01 1 10 100 1k 10 k 0.9 0.6 0.3 0 − 0.3 − 0.6 0 100 k VCC ± = ± 15 V f = 0.1 to 10 Hz TA = 25°C 1 2 THIRD-OCTAVE SPECTRAL NOISE DENSITY vs FREQUENCY BANDS Start Frequency: 12.5 Hz Stop Frequency: 20 kHz VCC ± = ± 15 V VIC = 0 TA = 25°C − 90 − 95 −100 −105 −110 −115 10 15 20 25 30 6 7 8 9 10 35 40 45 1 AV = 100, RL = 600 Ω 0.1 AV = 100, RL = 2 kΩ AV = 10, RL = 600 Ω 0.01 AV = 10, RL = 2 kΩ VCC ± = ± 5 V VO(PP) = 5 V TA = 25°C Filter: 10-Hz to 500-kHz Band Pass 0.001 10 Frequency Bands 100 1k f − Frequency − Hz Figure 56 62 5 TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY THD + N − Total Harmonic Distortion + Noise − % Third-Octave Spectrial Noise Density − dB − 75 − 85 4 Figure 55 Figure 54 − 80 3 t − Time − s Noise Bandwidth − Hz Figure 57 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 10 k 100 k TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS UNITY-GAIN BANDWIDTH vs LOAD CAPACITANCE 1 13 Filter: 10-Hz to 500-kHz Band Pass VCC ± = ± 15 V VO(PP) = 20 V TA = 25°C 0.1 B1 B1 − Unity-Gain Bandwidth − MHz THD + N − Total Harmonic Distortion + Noise − % TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY AV = 100, RL = 600 Ω AV = 100, RL = 2 kΩ 0.01 AV = 10, RL = 600 Ω AV = 10, RL = 2 kΩ 0.001 10 VCC ± = ± 15 V VIC = 0 VO = 0 RL = 2 kΩ TA = 25°C 12 11 10 9 8 7 100 1k 10 k 100 k 0 20 f − Frequency − Hz 40 Figure 58 100 GAIN-BANDWIDTH PRODUCT vs SUPPLY VOLTAGE 13 13 f = 100 kHz VIC = 0 VO = 0 RL = 2 kΩ CL = 100 pF 12 11 VCC ± = ± 15 V 10 VCC ± = ± 5 V 9 8 7 −75 − 55 − 35 −15 Gain-Bandwidth Product − MHz Gain-Bandwidth Product − MHz 80 Figure 59 GAIN-BANDWIDTH PRODUCT† vs FREE-AIR TEMPERATURE f = 100 kHz VIC = 0 VO = 0 RL = 2 kΩ CL = 100 pF TA = 25°C 12 11 10 9 8 7 5 25 45 65 85 105 125 0 5 TA − Free-Air Temperature − °C 10 15 20 25 |VCC VCC+± | − Supply Voltage − V Figure 60 † 60 CL − Load Capacitance − pF Figure 61 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 63 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS PHASE MARGIN† vs FREE-AIR TEMPERATURE GAIN MARGIN vs LOAD CAPACITANCE 10 80° VIC = 0 VO = 0 RL = 2 kΩ 70° xm φ m − Phase Margin 8 Gain Margin − dB 90° VCC ± = ± 15 V VIC = 0 VO = 0 RL = 2 kΩ TA = 25°C 6 4 VCC ± = ± 15 V CL = 25 pF 60° VCC ± = ± 5 V 50° VCC ± = ± 15 V 40° 30° CL = 100 pF VCC ± = ± 5 V 20° 2 10° 0° −75 − 55 − 35 −15 0 0 20 40 60 80 100 Figure 62 80° 80° 70° 70° CL = 25 pF xm φ m − Phase Margin xm φ m − Phase Margin 90° 50° CL = 100 pF 40° 30° VIC = 0 VO = 0 RL = 2 kΩ TA = 25°C 10° 85 105 125 VCC ± = ± 15 V 50° VCC ± = ± 5 V 40° 30° VIC = 0 VO = 0 RL = 2 kΩ TA = 25°C 10° 0° 0 4 8 12 16 20 0 |VCC ±| − Supply Voltage − V 20 40 60 80 100 CL − Load Capacitance − pF Figure 64 64 65 60° 20° 0° † 45 PHASE MARGIN vs LOAD CAPACITANCE 90° 20° 25 Figure 63 PHASE MARGIN vs SUPPLY VOLTAGE 60° 5 TA − Free-Air Temperature − °C CL − Load Capacitance − pF Figure 65 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS NONINVERTING LARGE-SIGNAL PULSE RESPONSE† SMALL-SIGNAL PULSE RESPONSE 100 15 TA = 25°C, 125°C VO VO − Output Voltage − mV VO VO − Output Voltage − V 10 TA = − 55°C 5 TA = − 55°C 0 TA = 25°C, 125°C −5 VCC ± = ± 15 V AV = 1 RL = 2 kΩ CL = 100 pF − 10 − 15 50 0 VCC ± = ± 15 V AV = − 1 RL = 2 kΩ CL = 100 pF TA = 25°C − 50 −100 0 1 2 3 t − Time − μs 4 5 0 Figure 66 TLE2072 AND TLE2074 CROSSTALK ATTENUATION vs FREQUENCY 100 140 VCC ± = ± 15 V TA = 25°C 120 10 1 Crosstalk Attenuation − dB Ω zo − Closed-Loop Output Impedance − X zo 1.6 Figure 67 CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY AV = 100 0.1 AV = 10 0.01 AV = 1 100 80 60 40 0.001 10 100 1k 10 k 100 k 1M 10 M 20 10 VCC ± = ± 15 V VIC = 0 RL = 2 kΩ TA = 25°C 100 1k 10 k 100 k f − Frequency − Hz f − Frequency − Hz Figure 69 Figure 68 † 1.2 0.4 0.8 t − Time − μs Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 65 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 APPLICATION INFORMATION input characteristics The TLE207x, TLE207xA, and TLE207xB are specified with a minimum and a maximum input voltage that if exceeded at either input could cause the device to malfunction. Because of the extremely high input impedance and resulting low bias current requirements, the TLE207x, TLE207xA, and TLE207xB are well suited for low-level signal processing; however, leakage currents on printed-circuit boards and sockets can easily exceed bias current requirements and cause degradation in system performance. It is good practice to include guard rings around inputs (see Figure 70). These guards should be driven from a low-impedance source at the same voltage level as the common-mode input. + VI VI VO + + VO − − R1 R2 VO VI − R3 R4 Where R3 + R2 R1 R4 Figure 70. Use of Guard Rings TLE2071 input offset voltage nulling The TLE2071 series offers external null pins that can be used to further reduce the input offset voltage. The circuit of Figure 71 can be connected as shown if the feature is desired. When external nulling is not needed, the null pins may be left unconnected. IN − − IN + + OUT N1 N2 100 kΩ 5 kΩ VCC − Figure 71. Input Offset Voltage Nulling 66 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 APPLICATION INFORMATION macromodel information Macromodel information provided was derived using PSpice™ Parts ™ model generation software. The Boyle macromodel (see Note 4) and subcircuit Figure 72 were generated using the TLE207x typical electrical and operating characteristics at TA = 25°C. Using this information, output simulations of the following key parameters can be generated to a tolerance of 20% (in most cases): D D D D D D D D D D D D Maximum positive output voltage swing Maximum negative output voltage swing Slew rate Quiescent power dissipation Input bias current Open-loop voltage amplification Unity-gain frequency Common-mode rejection ratio Phase margin DC output resistance AC output resistance Short-circuit output current limit NOTE 4: G.R. Boyle, B.M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journal of Solid-State Circuits, SC-9, 353 (1974). 99 3 VCC + EGND + 9 RSS + ISS 92 FB 10 IN − J1 DP VC J2 IN+ 11 R2 − 53 DC 12 HLIM − + C2 6 VCC − 54 4 − − − − + VLN + GCM GA VLIM 8 RD2 91 + VLP 7 C1 RD1 + DLP 90 RO2 VB RP 2 1 − DLN − RO1 DE 5 + VE OUT .SUBCKT TLE2074 1 2 3 4 5 C1 11 12 2.2E−12 C2 6 7 10.00E−12 DC 5 53 DX DE 54 5 DX DLP 90 91 DX DLN 92 90 DX DP 4 3 DX EGND 99 0 POLY (2) (3,0) (4,0) 0 .5 .5 FB 7 99 POLY (5) VB VC VE VLP VLN 0 + 5.607E6 −6E6 6E6 6E6 −6E6 GA 6 0 11 12 333.0E−6 GCM 0 6 10 99 7.43E−9 ISS 3 10 DC 400.0E−6 HLIM 90 0 VLIM 1K J1 11 2 10 JX J2 12 1 10 JX R2 6 9 100.0E3 RD1 4 11 3.003E3 RD2 4 12 3.003E3 R01 8 5 80 R02 7 99 80 RP 3 4 27.30E3 RSS 10 99 500.0E3 VB 9 0 DC 0 VC 3 53 DC 2.20 VE 54 4 DC 2.20 VLIM 7 8 DC 0 VLP 91 0 DC 45 VLN 0 92 DC 45 .MODEL DX D (IS=800.0E−18) .MODEL JX PJF (IS=15.00E−12 BETA=554.5E−6 + VTO=−.6) .ENDS Figure 72. Boyle Macromodel and Subcircut PSpice and Parts are trademarks of MicroSim Corporation. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 67 TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS  SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009 Revision History Version Date Changes C Dec−2009 – For TLE2071M/1AM (VCC ±5V) changed Vn NOM & MAX from 28/55 to 48/85 (f = 10 Hz); 11.6/17 to 12/17 (f = 10 KHz), Pg. 16 – For TLE2071M/1AM (VCC ±15V) changed Vn NOM & MAX from 28/55 to 48/85 (f = 10 Hz); 11.6/17 to 12/17 (f = 10 KHz), Pg. 18 – For TLE2072M/2AM (VCC ±5V) changed Vn NOM & MAX from 28/55 to 48/85 (f = 10 Hz); 11.6/17 to 12/17 (f = 10 KHz), Pg. 29 – For TLE2072M/2AM (VCC ±15V) changed Vn NOM & MAX from 28/55 to 48/85 (f = 10 Hz); 11.6/17 to 12/17 (f = 10 KHz), Pg. 31 – For TLE2074M/4AM (VCC ±5V) changed Vn NOM & MAX from 28/55 to 48/85 (f = 10 Hz); 11.6/17 to 12/17 (f = 10 KHz), Pg. 42 – For TLE2074M/4AM (VCC ±15V) changed Vn NOM & MAX from 28/55 to 48/85 (f = 10 Hz); 11.6/17 to 12/17 (f = 10 KHz), Pg. 44 68 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 14-Aug-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) (3) Device Marking (4/5) (6) 5962-9460201Q2A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629460201Q2A TLE2071 MFKB 5962-9460201QPA ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460201QPA TLE2071M 5962-9460202Q2A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629460202Q2A TLE2072 MFKB 5962-9460202QHA ACTIVE CFP U 10 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460202QHA TLE2072M 5962-9460202QPA ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460202QPA TLE2072M 5962-9460203Q2A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629460203Q2A TLE2074 MFKB 5962-9460203QCA ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9460203QC A TLE2074MJB 5962-9460204Q2A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962 9460204Q2A TLE2071 AMFKB 5962-9460204QHA ACTIVE CFP U 10 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460204QHA TLE2071AM 5962-9460204QPA ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460204QPA TLE2071AM 5962-9460205Q2A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629460205Q2A TLE2072 AMFKB 5962-9460205QHA ACTIVE CFP U 10 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460205QHA TLE2072AM Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Aug-2021 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) 5962-9460205QPA ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460205QPA TLE2072AM 5962-9460206Q2A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629460206Q2A TLE2074 AMFKB 5962-9460206QCA ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9460206QC A TLE2074AMJB 5962-9460206QDA ACTIVE CFP W 14 1 Non-RoHS & Non-Green SNPB N / A for Pkg Type -55 to 125 5962-9460206QD A TLE2074AMWB TLE2071ACD ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 TLE2071ACDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM TLE2071ACP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2071AC TLE2071ACPE4 ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2071AC TLE2071AID ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 2071AI TLE2071AIDG4 ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 2071AI TLE2071AIDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM TLE2071AIP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2071AMFKB ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962 9460204Q2A TLE2071 AMFKB TLE2071AMJG ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 TLE2071 AMJG TLE2071AMJGB ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460204QPA TLE2071AM TLE2071AMUB ACTIVE CFP U 10 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460204QHA TLE2071AM Addendum-Page 2 2071AC 2071AC 2071AI TLE2071AI Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Aug-2021 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) TLE2071CD ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 2071C TLE2071CDG4 ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 2071C TLE2071CP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2071CP TLE2071CPE4 ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2071CP TLE2071ID ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 2071I TLE2071IDG4 ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 2071I TLE2071IDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM TLE2071IP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2071MFKB ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629460201Q2A TLE2071 MFKB TLE2071MJG ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 TLE2071MJG TLE2071MJGB ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460201QPA TLE2071M TLE2072ACD ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 TLE2072ACP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2072AC TLE2072ACPE4 ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2072AC TLE2072AID ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 2072AI TLE2072AIDG4 ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 2072AI TLE2072AIDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM TLE2072AIP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2072AMFKB ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type Addendum-Page 3 2071I TLE2071IP 2072AC 2072AI TLE2072AI -55 to 125 59629460205Q2A TLE2072 Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Aug-2021 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) AMFKB TLE2072AMJG ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 TLE2072 AMJG TLE2072AMJGB ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460205QPA TLE2072AM TLE2072AMUB ACTIVE CFP U 10 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460205QHA TLE2072AM TLE2072CD ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 2072C TLE2072CDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 2072C TLE2072CDRG4 ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 2072C TLE2072CP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2072ID ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM TLE2072IDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 2072I TLE2072IDRG4 ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 2072I TLE2072IP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TLE2072MFKB ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629460202Q2A TLE2072 MFKB TLE2072MJG ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 TLE2072MJG TLE2072MJGB ACTIVE CDIP JG 8 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460202QPA TLE2072M TLE2072MUB ACTIVE CFP U 10 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 9460202QHA TLE2072M TLE2074ACDW ACTIVE SOIC DW 16 40 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 TLE2074ACN ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type TLE2074ACN TLE2074ACNE4 ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type TLE2074ACN Addendum-Page 4 TLE2072CP 2072I TLE2072IP TLE2074AC Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Aug-2021 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) TLE2074AIDW ACTIVE SOIC DW 16 40 RoHS & Green NIPDAU Level-1-260C-UNLIM TLE2074AIN ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type TLE2074AIN TLE2074AINE4 ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type TLE2074AIN TLE2074AMFKB ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629460206Q2A TLE2074 AMFKB TLE2074AMJ ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 TLE2074AMJ TLE2074AMJB ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9460206QC A TLE2074AMJB TLE2074AMWB ACTIVE CFP W 14 1 Non-RoHS & Non-Green SNPB N / A for Pkg Type -55 to 125 5962-9460206QD A TLE2074AMWB TLE2074CDW ACTIVE SOIC DW 16 40 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 TLE2074CDWR ACTIVE SOIC DW 16 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM TLE2074CN ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type TLE2074CN TLE2074CNE4 ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type TLE2074CN TLE2074IDW ACTIVE SOIC DW 16 40 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 TLE2074I TLE2074IDWG4 ACTIVE SOIC DW 16 40 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 TLE2074I TLE2074IDWR ACTIVE SOIC DW 16 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM TLE2074IN ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type TLE2074MFKB ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629460203Q2A TLE2074 MFKB TLE2074MJ ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 TLE2074MJ Addendum-Page 5 -40 to 85 TLE2074AI TLE2074C TLE2074C TLE2074I TLE2074IN Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Aug-2021 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) TLE2074MJB ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9460203QC A TLE2074MJB (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of