TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
D
D
D
D
D
D
D
Micro-Power Operation . . . < 1 µA/Channel
Input Common-Mode Range Exceeds the
Rails . . . –0.1 V to VCC + 5 V
Reverse Battery Protection Up To 18 V
Rail-to-Rail Input/Output
Gain Bandwidth Product . . . 5.5 kHz
Supply Voltage Range . . . 2.5 V to 16 V
Specified Temperature Range
– TA = 0°C to 70°C . . . Commercial Grade
– TA = –40°C to 125°C . . . Industrial Grade
Ultrasmall Packaging
– 5-Pin SOT-23 (TLV2401)
– 8-Pin MSOP (TLV2402)
Universal OpAmp EVM (Refer to the EVM
Selection Guide SLOU060)
Operational Amplifier
–
+
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
1.4
I CC – Supply Current – µ A/Ch
D
D
description
The TLV240x family of single-supply operational
amplifiers has the lowest supply current available
today at only 880 nA per channel. Reverse battery
protection guards the amplifier from an overcurrent condition due to improper battery
installation. For harsh environments, the inputs
can be taken 5 V above the positive supply rail
without damage to the device.
AV = 1
VIN = VCC / 2
TA = 25 °C
1.2
1.0
0.8
0.6
0.4
0.2
0
0
2
4
6
8
10
12
14
16
VCC – Supply Voltage – V
The low supply current is coupled with extremely low input bias currents enabling them to be used with mega-Ω
resistors making them ideal for portable, long active life, applications. DC accuracy is ensured with a low typical
offset voltage as low as 390 µV, CMRR of 120 dB and minimum open loop gain of 130 V/mV at 2.7 V.
The maximum recommended supply voltage is as high as 16 V and ensured operation down to 2.5 V, with
electrical characteristics specified at 2.7 V, 5 V and 15 V. The 2.5-V operation makes it compatible with Li-Ion
battery-powered systems and many micro-power microcontrollers available today including TI’s MSP430.
All members are available in PDIP and SOIC with the singles in the small SOT-23 package, duals in the MSOP,
and quads in TSSOP.
SELECTION OF SINGLE SUPPLY OPERATIONAL AMPLIFIER PRODUCTS†
DEVICE
VCC
(V)
VIO
(mV)
BW
(MHz)
SLEW RATE
(V/µs)
ICC/ch
(µA)
RAIL-TO-RAIL
TLV240x‡
2.5–16
0.390
0.005
0.002
0.880
I/O
TLV224x
2.5–12
0.600
0.005
0.002
1
I/O
TLV2211
2.7–10
0.450
0.065
0.025
13
O
TLV245x
2.7–6
0.020
0.22
0.110
23
I/O
TLV225x
2.7–8
0.200
0.2
0.12
35
O
† All specifications are typical values measured at 5 V.
‡ This device also offers 18-V reverse battery protection and 5-V over-the-rail operation on the inputs.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
TLV2401 AVAILABLE OPTIONS
VIOmax
AT 25°C
TA
0°C to 70°C
- 40°C to 125°C
1500 µV
PACKAGED DEVICES
SOT-23†
SYMBOLS
(DBV)
SMALL OUTLINE†
(D)
TLV2401CD
TLV2401CDBV
VAWC
TLV2401ID
TLV2401IDBV
VAWI
PLASTIC DIP
(P)
—
TLV2401IP
† This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g.,
TLV2401CDR).
TLV2402 AVAILABLE OPTIONS
VIOmax
AT 25°C
TA
0°C to 70°C
– 40°C to 125°C
1500 µV
PACKAGED DEVICES
MSOP†
SYMBOLS
(DGK)
SMALL OUTLINE†
(D)
PLASTIC DIP
(P)
TLV2402CD
TLV2402CDGK
xxTIAIX
—
TLV2402ID
TLV2402IDGK
xxTIAIY
TLV2402IP
† This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g.,
TLV2402CDR).
TLV2404 AVAILABLE OPTIONS
PACKAGED DEVICES
†
SMALL OUTLINE
PLASTIC DIP
(N)
(D)
VIOmax
AT 25°C
TA
0°C to 70°C
– 40°C to 125°C
1500 µV
TLV2404CD
TLV2404CN
TLV2404ID
TLV2404IN
TSSOP
(PW)
TLV2404CPW
TLV2404IPW
† This package is available taped and reeled. To order this packaging option, add an R suffix to the part
number (e.g., TLV2404CDR).
TLV240x PACKAGE PINOUTS
TLV2401
D OR P PACKAGE
(TOP VIEW)
TLV2401
DBV PACKAGE
(TOP VIEW)
OUT
GND
IN+
1
5
VCC
2
3
4
IN –
NC
IN –
IN +
GND
1
8
2
7
3
6
4
5
TLV2402
D, DGK, OR P PACKAGE
(TOP VIEW)
NC
VCC
OUT
NC
TLV2404
D, N, OR PW PACKAGE
(TOP VIEW)
1OUT
1IN –
1IN+
VCC
2IN+
2IN –
2OUT
1
14
2
13
3
12
4
11
5
10
6
9
7
8
4OUT
4IN –
4IN+
GND
3IN+
3IN –
3OUT
NC – No internal connection
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1OUT
1IN –
1IN +
GND
1
8
2
7
3
6
4
5
VCC
2OUT
2IN –
2IN+
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 V
Differential input voltage range, VID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 V
Input current range, II (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 mA
Output current range, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 mA
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 125°C
Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values, except differential voltages, are with respect to GND
DISSIPATION RATING TABLE
PACKAGE
ΘJC
(°C/W)
ΘJA
(°C/W)
TA ≤ 25°C
POWER RATING
D (8)
38.3
176
710 mW
142 mW
D (14)
26.9
122.6
1022 mW
204.4 mW
TA = 125°C
POWER RATING
DBV (5)
55
324.1
385 mW
77.1 mW
DGK (8)
54.2
259.9
481 mW
96.2 mW
N (14)
32
78
1600 mW
320.5 mW
P (8)
41
104
1200 mW
240.4 mW
PW (14)
29.3
173.6
720 mW
144 mW
recommended operating conditions
Single supply
Supply voltage
voltage, VCC
Split supply
Common-mode input voltage range, VICR
C-suffix
free air temperature,
temperature TA
Operating free-air
I-suffix
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MIN
MAX
2.5
16
±1.25
±8
–0.1
0
VCC+5
70
– 40
125
UNIT
V
V
°C
3
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
electrical characteristics at recommended operating conditions, VCC = 2.7, 5 V, and 15 V (unless
otherwise noted)
dc performance
PARAMETER
VIO
Input offset voltage
αVIO
Offset voltage draft
TEST CONDITIONS
VIC = 0 to VCC,
RS = 50 Ω
MAX
390
1200
1500
25°C
VCC = 5 V
7V
VCC = 2
2.7
V, VO(
V, RL = 500 kΩ
O(pp)) = 1 V
AVD
TYP
Full range
VCC = 15 V
Large-signal
g
g
differential voltage
g
amplification
MIN
25°C
VO = VCC/2 V,
VIC = VCC/2 V,
RS = 50 Ω
VCC = 2
2.7
7V
CMRR Common-mode
Common mode rejection ratio
TA†
VCC = 5 V
V,
VO(
V, RL = 500 kΩ
O(pp)) = 3 V
VCC = 15 V
V,
VO(
V, RL = 500 kΩ
O(pp)) = 6 V
63
Full range
60
25°C
70
Full range
63
25°C
80
Full range
75
25°C
130
Full range
30
25°C
300
Full range
100
25°C
1000
Full range
120
µV
µV/°C
3
25°C
UNIT
120
120
dB
120
400
1000
V/mV
1800
† Full range is 0°C to 70°C for the C suffix and –40°C to 125°C for the I suffix. If not specified, full range is – 40°C to 125°C.
input characteristics
PARAMETER
IIO
TEST CONDITIONS
Input offset current
TLV240xC
VO = VCC/2 V,
VIC = VCC/2 V
V,
RS = 50 Ω
IIB
Input bias current
TLV240xI
TYP
MAX
25
250
300
pA
400
100
300
350
Full range
25°C
UNIT
pA
900
300
MΩ
Ci(c)
Common-mode input capacitance
f = 100 kHz
25°C
3
† Full range is 0°C to 70°C for the C suffix and –40°C to 125°C for the I suffix. If not specified, full range is – 40°C to 125°C.
pF
4
Differential input resistance
MIN
Full range
25°C
TLV240xC
TLV240xI
ri(d)
TA†
25°C
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
electrical characteristics at recommended operating conditions, VCC = 2.7, 5 V, and 15 V (unless
otherwise noted) (continued)
output characteristics
PARAMETER
TEST CONDITIONS
VCC = 2
2.7
7V
VIC = VCC/2,,
IOH = –2 µA
VCC = 5 V
VCC = 15 V
VOH
High level output voltage
High-level
VCC = 2
2.7
7V
VIC = VCC/2,,
IOH = –50 µA
VCC = 5 V
VCC = 15 V
/2 IOL = 2 µA
VIC = VCC/2,
VOL
Low level output voltage
Low-level
VIC = VCC/2,
/2 IOL = 50 µA
TA†
25°C
MIN
TYP
2.65
2.68
Full range
2.63
25°C
4.95
Full range
4.93
25°C
14.95
Full range
14.93
25°C
2.62
Full range
2.6
25°C
4.92
Full range
4.9
25°C
14.92
Full range
14.9
25°C
MAX
4.98
14.98
V
2.65
4.95
14.95
90
Full range
150
180
25°C
UNIT
180
Full range
230
mV
260
IO
Output current
VO = 0.5 V from rail
25°C
±200
† Full range is 0°C to 70°C for the C suffix and –40°C to 125°C for the I suffix. If not specified, full range is – 40°C to 125°C.
µA
power supply
PARAMETER
TEST CONDITIONS
VCC = 2.7
2 7 V or 5 V
ICC
Supply current (per channel)
VO = VCC/2
VCC = 15 V
Reverse supply current
PSRR
Power supply rejection ratio
(∆VCC/∆VIO)
VCC = –18 V, VIN = 0 V,
VO = Open circuit
TA†
25°C
TLV240xC
VCC = 5 to 15 V,
No load
VIC = VCC/2 V,
TLV240xI
TYP
MAX
880
950
Full range
1290
25°C
900
Full range
Full range
990
UNIT
nA
1350
25°C
25°C
VCC = 2.7 to 5 V,
VIC = VCC/2 V,
No load,
MIN
50
100
120
96
85
25°C
100
Full range
100
nA
dB
dB
120
dB
† Full range is 0°C to 70°C for the C suffix and –40°C to 125°C for the I suffix. If not specified, full range is – 40°C to 125°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
electrical characteristics at recommended operating conditions, VCC = 2.7, 5 V, and 15 V (unless
otherwise noted) (continued)
dynamic performance
PARAMETER
TEST CONDITIONS
UGBW
Unity gain bandwidth
RL = 500 kΩ,
SR
Slew rate at unity gain
VO(pp) = 0.8 V,
RL = 500 kΩ,
φM
Phase margin
RL = 500 kΩ
kΩ,
CL = 100 pF
Gain margin
ts
VCC = 2.7 or 5 V,
V(STEP)PP = 1 V,
AV = –1,
VCC = 15 V,
V(STEP)PP = 1 V
V,
AV = –1,
Settling time
CL = 100 pF,
RL = 100 kΩ
CL = 100 pF
F,
RL = 100 kΩ
CL = 100 pF
TA
25°C
CL = 100 pF
25°C
MIN
TYP
MAX
UNIT
5.5
kHz
2.5
V/ms
60°
25°C
15
0.1%
dB
1.84
25°C
ms
0.1%
6.1
0.01%
32
noise/distortion performance
PARAMETER
Vn
Equivalent input noise voltage
In
Equivalent input noise current
6
TEST CONDITIONS
TA
f = 10 Hz
f = 100 Hz
f = 100 Hz
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MIN
TYP
800
25°C
500
8
MAX
UNIT
nV/√Hz
fA/√Hz
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
Input Offset Voltage
vs Common-mode input voltage
1, 2, 3
vs Free-air temperature
4, 6, 8
vs Common-mode input voltage
5, 7, 9
vs Free-air temperature
4, 6, 8
vs Common-mode input voltage
5, 7, 9
IIB
Input Bias Current
IIO
Input Offset Current
CMRR
Common-mode rejection ratio
vs Frequency
VOH
VOL
High-level output voltage
vs High-level output current
11, 13, 15
Low-level output voltage
vs Low-level output current
12, 14, 16
VO(PP)
Zo
Output voltage peak-to-peak
vs Frequency
17
Output impedance
vs Frequency
18
ICC
PSRR
Supply current
vs Supply voltage
19
Power supply rejection ratio
vs Frequency
20
AVD
Differential voltage gain
vs Frequency
21
Phase
vs Frequency
21
Gain-bandwidth product
vs Supply voltage
22
SR
Slew rate
vs Free-air temperature
23
φm
Phase margin
vs Capacitive load
24
Gain margin
vs Capacitive load
25
Supply current
vs Reverse voltage
26
Voltage noise over a 10 Second Period
10
27
Large signal follower pulse response
28, 29, 30
Small signal follower pulse response
31
Large signal inverting pulse response
32, 33, 34
Small signal inverting pulse response
35
Crosstalk
vs Frequency
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
36
7
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
TYPICAL CHARACTERISTICS
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT
VOLTAGE
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT
VOLTAGE
800
600
400
200
0
0
–100
–200
–300
VCC = 5 V
TA = 25 °C
–400
–0.2
–0.1 0.4 1.0 1.6 2.2 2.8 3.4 4.0 4.6 5.2
–200
–0.20
–0.1 0.20 0.60 1.00 1.40 1.80 2.20 2.60 2.9
Figure 1
200
100
IIO
0
IIB
–100
–200
–40 –25 –10 5
I IB / I IO – Input Bias / Offset Current – pA
20 35 50 65 80 95 110 125
350
300
IIO
0
–50
IIB
–100
–150
–0.2 0.4 1.0 1.6 2.2 2.8 3.4 4.0 4.6 5.2
–0.1
VICR – Common Mode Input Voltage – V
Figure 7
8
4.2
200
150
100
50
IIO
0
–50
IIB
–100
–150
–0.2
–0.1 0.2
8.6
10.8 13.0 15.2
0.6
1.0
1.4
1.8
2.2
2.6 2.9
400
300
200
100
IIO
0
IIB
–100
–200
–40 –25 –10 5
20 35 50 65 80 95 110 125
TA – Free-Air Temperature – °C
Figure 6
Figure 5
INPUT BIAS / OFFSET CURRENT
vs
COMMON-MODE INPUT
VOLTAGE
INPUT BIAS / OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
600
6.4
VCC = 5 V
VIC = 2.5 V
500
VICR – Common Mode Input Voltage – V
I IB / I IO – Input Bias / Offset Current – pA
I IB / I IO – Input Bias / Offset Current – pA
50
2.0
INPUT BIAS / OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
700
100
–300
600
VCC = 2.7 V
TA = 25 °C
Figure 4
150
–200
Figure 3
250
INPUT BIAS / OFFSET CURRENT
vs
COMMON-MODE INPUT
VOLTAGE
VCC = 5 V
TA = 25 °C
–100
VICR – Common-Mode Input Voltage –V
400
TA – Free-Air Temperature – °C
200
0
–400
–0.2
–0.1
250
VCC = 15 V
VIC = 7.5 V
500
400
300
200
100
IIO
0
–100
–200
–40 –25 –10 5
IIB
20 35 50 65 80 95 110 125
TA – Free-Air Temperature – °C
Figure 8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
I IB / I IO – Input Bias / Offset Current – pA
I IB / I IO – Input Bias / Offset Current – pA
300
100
INPUT BIAS / OFFSET CURRENT
vs
COMMON MODE INPUT
VOLTAGE
600
400
200
Figure 2
INPUT BIAS / OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
500
VCC = 15 V
TA = 25 °C
300
VICR – Common-Mode Input Voltage – V
VICR – Common-Mode Input Voltage – V
VCC = 2.7 V
VIC = 1.35 V
V IO – Input Offset Voltage – µV
1000
I IB / I IO – Input Bias / Offset Current – pA
VCC = 2.7 V
TA = 25°C
V IO – Input Offset Voltage – µV
V IO – Input Offset Voltage – µV
400
100
1400
1200
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT
VOLTAGE
VCC = 15 V
TA = 25 °C
200
150
100
50
IIO
0
–50
IIB
–100
–150
–0.2
–0.1
2.0
4.2
6.4
8.6
10.8 13.0 15.2
VICR – Common-Mode Input Voltage –V
Figure 9
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
TYPICAL CHARACTERISTICS
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
1.50
100
RF=100 kΩ
RI=1 kΩ
80
60
40
20
VCC = 2.7 V
2.4
TA = –40°C
2.1
TA = –0°C
TA = 25 °C
TA = 70 °C
TA = 125 °C
1.8
1.5
1.2
0
10
100
1k
f – Frequency – Hz
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
50
100
150
VOL – Low-Level Output Voltage – V
TA = –0°C
TA = 25 °C
TA = 70 °C
TA = 125 °C
4.0
3.5
150
TA = 0 °C
TA = –40°C
1.00
0.75
TA = 25 °C
TA = 70 °C
TA = 125 °C
0.50
0.25
0
50
100
150
Figure 14
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
OUTPUT VOLTAGE
PEAK-TO-PEAK
vs
FREQUENCY
V O(PP) – Output voltage Peak–to–Peak – V
TA = –40°C
TA = –0°C
TA = 25 °C
TA = 70 °C
TA = 125 °C
0.75
0.50
0.25
0
0
50
100
150
14.5
TA = –0°C
TA = 25 °C
TA = 70 °C
TA = 125 °C
14.0
13.5
TA = –40°C
VCC = 15 V
13
Figure 13
1.00
200
200
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
0
200
IOL – Low-Level Output Current – µA
1.25
150
Figure 12
1.25
200
VCC = 15 V
100
15.0
IOH – High-Level Output Current – µA
1.50
50
Figure 11
150
200
OUTPUT IMPEDANCE
vs
FREQUENCY
10k
14
VCC = 15 V
12
10
8
6
RL = 100 kΩ
CL = 100 pF
TA = 25°C
VCC = 5 V
2
VCC = 2.7 V
AV = 10
1k
AV = 1
100
0
VCC = 2.7, 5, & 15 V
TA = 25°C
–2
10
100
Figure 15
16
4
50
IOH – High-Level Output Current – µA
Z o – Output Impedance – Ω
100
0.25
0
0
50
TA = 70 °C
TA = 125 °C
0.50
IOL – Low-Level Output Current – µA
VCC = 5 V
3.0
0
0.75
IOH – High-Level Output Current – µA
V OH – High-Level Output Voltage – V
TA = –40°C
1.00
200
1.50
4.5
TA = 25 °C
TA = 0 °C
TA = –40°C
1.25
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
5.0
VCC = 5 V
VCC = 2.7 V
0
0
10k
Figure 10
V OH – High-Level Output Voltage – V
VOL – Low-Level Output Voltage – V
VCC=2.7, 5, 15 V
1
VOL – Low-Level Output Voltage – V
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
2.7
120
V OH – High-Level Output Voltage – V
CMRR – Common-Mode Rejection Ratio – dB
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
IOL – Low-Level Output Current – µA
100
f – Frequency – Hz
Figure 16
Figure 17
POST OFFICE BOX 655303
1k
• DALLAS, TEXAS 75265
10
100
1k
f – Frequency – Hz
10k
Figure 18
9
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
POWER SUPPLY REJECTION RATIO
vs
FREQUENCY
PSRR – Power Supply Rejection Ratio – dB
I CC – Supply Current – µ A/Ch
1.4
1.2
1.0
0.8
0.6
TA = 125°C
TA = 70 °C
TA = 25 °C
TA = 0 °C
TA = –40°C
0.4
0.2
AV = 1
VIN = VCC / 2
0
0
2
4
6
8
10
12
14
16
VCC = 2.7, 5, & 15 V
TA = 25°C
110
100
90
80
70
60
50
40
VCC – Supply Voltage – V
100
1k
f – Frequency – Hz
Figure 19
Figure 20
DIFFERENTIAL VOLTAGE GAIN AND PHASE
vs
FREQUENCY
GAIN BANDWIDTH PRODUCT
vs
SUPPLY VOLTAGE
10
90
30
45
20
10
0
0
VCC = 2.7, 5, & 15 V
RL = 500 kΩ
CL = 100 pF
TA = 25°C
–10
100
1k
f – Frequency – Hz
4
3
2
1
VCC – Supply Voltage –V
Figure 22
SLEW RATE
vs
FREE-AIR TEMPERATURE
PHASE MARGIN
vs
CAPACITIVE LOAD
80
3.0
70
SR+
VCC = 5, 15 V
60
VCC = 2.7 V
2.0
1.5
SR–
1.0
VCC = 2.7, 5, & 15 V
Phase Margin – °
SR – Slew Rate – V/ ms
5
TA = 25°C
RL = 100 kΩ
CL = 100 pF
f = 1 kHz
Figure 21
3.5
2.5
6
0
2.5 4.0 5.5 7.0 8.5 10.0 11.5 13.0 14.5 16.0
–45
10k
–20
10
GBWP –Gain Bandwidth Product – kHz
50
40
10k
7
135
Phase – °
AVD – Differential Voltage Gain – dB
60
50
40
30
20
0.5
10
0
–40 –25 –10 5
10
120
VCC = 2.7, 5, & 15 V
RL = 500 kΩ
TA = 25°C
0
20 35 50 65 80 95 110 125
TA – Free-Air Temperature – °C
100
1k
CL – Capacitive Load – pF
Figure 23
Figure 24
POST OFFICE BOX 655303
10
• DALLAS, TEXAS 75265
10k
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
TYPICAL CHARACTERISTICS
GAIN MARGIN
vs
CAPACITIVE LOAD
SUPPLY CURRENT
vs
REVERSE VOLTAGE
25
60
RL= 500 kΩ
TA = 25°C
55
I CC – Supply Current – nA
Gain Margin – dB
TA = 25°C
50
20
VCC = 15 V
15
10
VCC = 2.7 & 5 V
5
45
40
35
30
25
20
15
10
5
0
100
1k
CL – Capacitive Load – pF
0
–18 –16 –14 –12 –10
10k
–4
–6
–2
Figure 25
Figure 26
VOLTAGE NOISE
OVER A 10 SECOND PERIOD
LARGE SIGNAL FOLLOWER
PULSE RESPONSE
0
2
5
4
VCC = 5 V
f = 0.1 Hz to 10 Hz
TA = 25°C
3
Input Referred Voltage Noise – µV
–8
VCC – Reverse Voltage – V
4
V – Output Voltage – V
O
2
1
0
–1
–2
1
VIN
3
0
VCC = 2.7 V
AV = 1
RL = 100 kΩ
CL = 100 pF
TA = 25°C
2
1
VO
–1
V IN – Input Voltage – V
10
0
–3
–1
–4
2
3
4
5
6
7
8
9
–1
10
3
4
Figure 28
3
VIN
0
3
–1
IN
VO
V
1
20
10
5
15
0
10
–5
VO
5
V
4
V – Output Voltage – V
O
1
15
VCC = 15 V
AV = 1
RL = 100 kΩ
CL = 100 pF
TA = 25°C
25
2
– Input Voltage – V
5
6
30
4
VIN
5
LARGE SIGNAL FOLLOWER
PULSE RESPONSE
VCC = 5 V
AV = 1
RL = 100 kΩ
CL = 100 pF
TA = 25°C
7
V – Output Voltage – V
O
2
Figure 27
8
2
1
t – Time – ms
LARGE SIGNAL FOLLOWER
PULSE RESPONSE
6
0
t – Time – s
– Input Voltage – V
1
IN
0
0
0
–5
–1
–1
0
1
2
3
4
5
6
–2
0
2
4
6
8
10
t – Time – ms
t – Time – ms
Figure 29
Figure 30
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
12
14
16
11
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
TYPICAL CHARACTERISTICS
SMALL SIGNAL FOLLOWER
PULSE RESPONSE
LARGE SIGNAL INVERTING
PULSE RESPONSE
2.0
150
1.5
100
80
60
VO
–150
40
20
1
VCC = 2.7 V
AV = –1
RL = 100 kΩ
CL = 100 pF
TA = 25°C
0.5
0.0
–0.5
–1.0
VO
–1.5
0
–20
–50 0
–2
–1
50 100 150 200 250 300 350 400 450 500
0
1
t – Time – µs
4
5
6
LARGE SIGNAL INVERTING
PULSE RESPONSE
LARGE SIGNAL INVERTING
PULSE RESPONSE
4
12
2.0
3
10
2
8
1
6
0
VCC = 5 V
AV = –1
RL = 100 kΩ
CL = 100 pF
TA = 25°C
0.0
–0.5
–1.0
IN
–1.5
–1
–2.0
12
9
VIN
4
–3.0
0
VCC = 15 V
AV = –1
RL = 100 kΩ
CL = 100 pF
TA = 25°C
2
0
–2
–4
–3
–6
–8
VO
6
3
IN
0.5
7
V
1.0
– Input Voltage – V
VIN
V – Output Voltage – V
O
2.5
V
V – Output Voltage – V
O
3
Figure 32
–2.5
VO
–10
–3.5
–12
–1
0
1
2
3
4
5
6
7
–5
20
200
0
100
–20
–100
30
35
IN
–60
VCC = 2.7,
5, & 15 V
All Channels
RL = 100 kΩ
CL = 100 pF
VIN = 1 VPP
VCC = 15 V
–80
–100
VCC = 2.7, 5 V
V
VO
–40
Crosstalk –dB
0
– Input Voltage – mV
VCC = 2.7, 5,
& 15 V
AV = –1
RL = 100 kΩ
CL = 100 pF
TA = 25°C
25
CROSSTALK
vs
FREQUENCY
–50
–100
–150
–200
15
Figure 34
150
0
10
Figure 33
VIN
50
5
t – Time – ms
200
100
0
t – Time – ms
SMALL SIGNAL INVERTING
PULSE RESPONSE
VO – Output Voltage – mV
2
t – Time – ms
Figure 31
1.5
12
0
–1
IN
VCC = 2.7, 5,
& 15 V
AV = 1
RL = 100 kΩ
CL = 100 pF
TA = 25°C
120
2
1.0
V
0
–120
–140
0
200
400
600
800 1000 1200
t – Time – ms
100
1k
f – Frequency –Hz
Figure 35
Figure 36
POST OFFICE BOX 655303
– Input Voltage – V
V – Output Voltage – mV
O
140
3
VIN
– Input Voltage – V
300
V – Output Voltage – V
O
VIN
160
V IN – Input Voltage – mV
180
10
• DALLAS, TEXAS 75265
10k
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
APPLICATION INFORMATION
reverse battery protection
The TLV2401/2/4 are protected against reverse battery voltage up to 18 V. When subjected to reverse battery
condition the supply current is typically less than 100 nA at 25°C (inputs grounded and outputs open). This
current is determined by the leakage of 6 Schottky diodes and will therefore increase as the ambient
temperature increases.
When subjected to reverse battery conditions and negative voltages applied to the inputs or outputs, the input
ESD structure will turn on—this current should be limited to less than 10 mA. If the inputs or outputs are referred
to ground, rather than midrail, no extra precautions need be taken.
common-mode input range
The TLV2401/2/4 has rail-to-rail input and outputs. For common-mode inputs from –0.1 V to VCC – 0.8 V a PNP
differential pair will provide the gain.
For inputs between VCC – 0.8 V and VCC, two NPN emitter followers buffering a second PNP differential pair
provide the gain. This special combination of NPN/PNP differential pair enables the inputs to be taken 5 V above
the rails, because as the inputs go above VCC, the NPNs switch from functioning as transistors to functioning
as diodes. This will lead to an increase in input bias current. The second PNP differential pair continues to
function normally as the inputs exceed VCC.
The TLV2401/2/4 has a negative common-input range that exceeds ground by 100 mV. If the inputs are taken
much below this, reduced open loop gain will be observed with the ultimate possibility of phase inversion.
offset voltage
The output offset voltage, (VOO) is the sum of the input offset voltage (VIO) and both input bias currents (IIB) times
the corresponding gains. The following schematic and formula can be used to calculate the output offset
voltage:
RF
IIB–
RG
+
–
VI
VO
+
RS
ǒ ǒ ǓǓ ǒ ǒ ǓǓ
IIB+
V
OO
+ VIO 1 )
R
R
F
G
" IIB) RS
1
)
R
R
F
G
" IIB– RF
Figure 37. Output Offset Voltage Model
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
APPLICATION INFORMATION
general configurations
When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often
required. The simplest way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier
(see Figure 38).
RG
RF
–
VO
+
VI
R1
V
O
V
I
C1
ǒ Ǔǒ
+ 1 ) RRF
G
1
f
–3dB
Ǔ
1
+ 2pR1C1
) sR1C1
1
Figure 38. Single-Pole Low-Pass Filter
If even more attenuation is needed, a multiple pole filter is required. The Sallen-Key filter can be used for this
task. For best results, the amplifier should have a bandwidth that is 8 to 10 times the filter frequency bandwidth.
Failure to do this can result in phase shift of the amplifier.
C1
+
_
VI
R1
R1 = R2 = R
C1 = C2 = C
Q = Peaking Factor
(Butterworth Q = 0.707)
R2
f
C2
RG
RF
RG =
Figure 39. 2-Pole Low-Pass Sallen-Key Filter
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
–3dB
+ 2p1RC
(
RF
1
2–
Q
)
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
APPLICATION INFORMATION
circuit layout considerations
To achieve the levels of high performance of the TLV240x, follow proper printed-circuit board design techniques.
A general set of guidelines is given in the following.
D
D
D
D
D
Ground planes – It is highly recommended that a ground plane be used on the board to provide all
components with a low inductive ground connection. However, in the areas of the amplifier inputs and
output, the ground plane can be removed to minimize the stray capacitance.
Proper power supply decoupling – Use a 6.8-µF tantalum capacitor in parallel with a 0.1-µF ceramic
capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers
depending on the application, but a 0.1-µF ceramic capacitor should always be used on the supply terminal
of every amplifier. In addition, the 0.1-µF capacitor should be placed as close as possible to the supply
terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less
effective. The designer should strive for distances of less than 0.1 inches between the device power
terminals and the ceramic capacitors.
Sockets – Sockets can be used but are not recommended. The additional lead inductance in the socket pins
will often lead to stability problems. Surface-mount packages soldered directly to the printed-circuit board
is the best implementation.
Short trace runs/compact part placements – Optimum high performance is achieved when stray series
inductance has been minimized. To realize this, the circuit layout should be made as compact as possible,
thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting input of
the amplifier. Its length should be kept as short as possible. This will help to minimize stray capacitance at
the input of the amplifier.
Surface-mount passive components – Using surface-mount passive components is recommended for high
performance amplifier circuits for several reasons. First, because of the extremely low lead inductance of
surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small
size of surface-mount components naturally leads to a more compact layout thereby minimizing both stray
inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be
kept as short as possible.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
APPLICATION INFORMATION
general power dissipation considerations
ǒ Ǔ
For a given θJA, the maximum power dissipation is shown in Figure 40 and is calculated by the following formula:
P
Where:
+
D
T
–T
MAX A
q JA
PD = Maximum power dissipation of THS240x IC (watts)
TMAX = Absolute maximum junction temperature (150°C)
TA
= Free-ambient air temperature (°C)
θJA = θJC + θCA
θJC = Thermal coefficient from junction to case
θCA = Thermal coefficient from case to ambient air (°C/W)
MAXIMUM POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
2
Maximum Power Dissipation – W
1.75
PDIP Package
Low-K Test PCB
θJA = 104°C/W
1.5
1.25
SOIC Package
Low-K Test PCB
θJA = 176°C/W
TJ = 150°C
MSOP Package
Low-K Test PCB
θJA = 260°C/W
1
0.75
0.5
0.25
SOT-23 Package
Low-K Test PCB
θJA = 324°C/W
0
–55 –40 –25 –10 5 20 35 50 65 80 95 110 125
TA – Free-Air Temperature – °C
NOTE A: Results are with no air flow and using JEDEC Standard Low-K test PCB.
Figure 40. Maximum Power Dissipation vs Free-Air Temperature
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLV2401, TLV2402, TLV2404
FAMILY OF 880-nA/Ch RAIL-TO-RAIL INPUT/OUTPUT
OPERATIONAL AMPLIFIERS WITH REVERSE BATTERY PROTECTION
SLOS244B – FEBRUARY 2000 – REVISED NOVEMBER 2000
APPLICATION INFORMATION
macromodel information
Macromodel information provided was derived using Microsim Parts Release 8, the model generation
software used with Microsim PSpice . The Boyle macromodel (see Note 2) and subcircuit in Figure 41 are
generated using the TLV240x typical electrical and operating characteristics at TA = 25°C. Using this
information, output simulations of the following key parameters can be generated to a tolerance of 20% (in most
cases):
D
D
D
D
D
D
D
D
D
D
D
D
Maximum positive output voltage swing
Maximum negative output voltage swing
Slew rate
Quiescent power dissipation
Input bias current
Open-loop voltage amplification
Unity-gain frequency
Common-mode rejection ratio
Phase margin
DC output resistance
AC output resistance
Short-circuit output current limit
NOTE 2: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journal
of Solid-State Circuits, SC-9, 353 (1974).
3
99
VCC+
+
egnd
ree
ro2
cee
fb
rp
rc1
rc2
–
c1
7
11
12
+
1
c2
vlim
IN+
r2
+
9
6
–
vc
2
8
+
q1
q2
IN–
–
vb
ga
–
ro1
gcm
ioff
53
dp 13
14
re1
VOUT
re2
91
10
iee
VCC–
4
+
vlp
+ 54
5
92
–
hlim
–
ve
dln
90
+
dc
–
dlp
–
vln
+
de
.subckt 240X_5V–X 1 2 3 4 5
*
c1
11 12 9.8944E–12
c2
6 7 30.000E–12
cee 10 99 8.8738E–12
dc
5 53 dy
de
54 5 dy
dlp
90 91 dx
dln
92 90 dx
dp
4 3 dx
egnd 99 0 poly(2) (3,0) (4,0) 0 .5 .5
fb
7 99 poly(5) vb vc ve vlp vln 0 61.404E6 –1E3 1E3 61E6 –61E6
ga
6 0 11 12 1.0216E–6
gcm 0 6 10 99 10.216E–12
iee
10 4 dc 54.540E–9
ioff
0 6 dc 5e–12
hlim 90 0 vlim 1K
q1
11 2 13 qx1
q2
12 1 14 qx2
r2
6 9 100.00E3
rc1
rc2
re1
re2
ree
ro1
ro2
rp
vb
vc
ve
vlim
vlp
vln
.model
.model
.model
.model
.ends
3
3
13
14
10
8
7
3
9
3
54
7
91
0
dx
dy
qx1
qx2
11 978.81E3
12 978.81E3
10 30.364E3
10 30.364E3
99 3.6670E9
5 10
99 10
4 1.4183E6
0 dc 0
53 dc .88315
4 dc .88315
8 dc 0
0 dc 540
92 dc 540
D(Is=800.00E–18)
D(Is=800.00E–18 Rs=1m Cjo=10p)
NPN(Is=800.00E–18 Bf=27.270E21)
NPN(Is=800.0000E–18 Bf=27.270E21)
Figure 41. Boyle Macromodels and Subcircuit
PSpice and Parts are trademarks of MicroSim Corporation.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
TLV2401CD
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
2401C
Samples
TLV2401CDBVR
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
VAWC
Samples
TLV2401CDBVT
ACTIVE
SOT-23
DBV
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
VAWC
Samples
TLV2401CDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
2401C
Samples
TLV2401ID
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
2401I
Samples
TLV2401IDBVR
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
VAWI
Samples
TLV2401IDBVT
ACTIVE
SOT-23
DBV
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
VAWI
Samples
TLV2401IDBVTG4
ACTIVE
SOT-23
DBV
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
VAWI
Samples
TLV2401IDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
2401I
Samples
TLV2401IP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
TLV2401I
Samples
TLV2402CD
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
2402C
Samples
TLV2402CDGK
ACTIVE
VSSOP
DGK
8
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
AIX
Samples
TLV2402CDGKR
ACTIVE
VSSOP
DGK
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
AIX
Samples
TLV2402CDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
2402C
Samples
TLV2402ID
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
2402I
Samples
TLV2402IDG4
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
2402I
Samples
TLV2402IDGK
ACTIVE
VSSOP
DGK
8
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
AIY
Samples
TLV2402IDGKR
ACTIVE
VSSOP
DGK
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
AIY
Samples
TLV2402IDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
2402I
Samples
TLV2402IDRG4
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
2402I
Samples
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
TLV2402IP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
TLV2402I
Samples
TLV2404CD
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
TLV2404C
Samples
TLV2404CPW
ACTIVE
TSSOP
PW
14
90
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
2404C
Samples
TLV2404CPWR
ACTIVE
TSSOP
PW
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
2404C
Samples
TLV2404ID
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TLV2404I
Samples
TLV2404IDR
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TLV2404I
Samples
TLV2404IN
ACTIVE
PDIP
N
14
25
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
TLV2404IN
Samples
TLV2404IPW
ACTIVE
TSSOP
PW
14
90
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
2404I
Samples
TLV2404IPWR
ACTIVE
TSSOP
PW
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
2404I
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
