TLV3012AIDCKRG4

TLV3011 TLV3012 SBOS300B – FEBRUARY 2004 – REVISED JUNE 2004 Nanopower, 1.8V, SOT23 Comparator with Voltage Reference FEATURES q LOW QUIESCENT CURRENT: 5µA (max) q INTEGRATED VOLTAGE REFERENCE: 1.242V q INPUT COMMON-MODE RANGE: 200mV Beyond Rails q VOLTAGE REFERENCE INITIAL ACCURACY: 1% q OPEN-DRAIN LOGIC COMPATIBLE OUTPUT: TLV3011 q PUSH-PULL OUTPUT: TLV3012 q LOW-SUPPLY VOLTAGE: 1.8V to 5.5V q FAST RESPONSE TIME: 6µs Propagation Delay with 100mV Overdrive (TLV3011: RPULL-UP = 10kΩ) q MicroSIZE PACKAGES: SOT23-6 and SC70-6 DESCRIPTION The TLV3011 is a low-power, open-drain output comparator; the TLV3012 is a push-pull output comparator. Both feature an uncommitted on-chip voltage reference. Both have 5µA (max) quiescent current, input common-mode range 200mV beyond the supply rails, and single-supply operation from 1.8V to 5.5V. The integrated 1.242V series voltage reference offers low 100ppm/°C (max) drift, is stable with up to 10nF capacitive load, and can provide up to 0.5mA (typ) of output current. The TLV3011 and TLV3012 are available in the tiny SOT23-6 package for space-conservative designs. It is also available in the SC70 package for even greater board area savings. Both versions are specified for the temperature range of –40°C to +125°C. APPLICATIONS q q q q q BATTERY-POWERED LEVEL DETECTION DATA ACQUISITION SYSTEM MONITORING OSCILLATORS SENSOR SYSTEMS: Smoke Detectors, Light Sensors, Alarms TLV3011 and TLV3012 RELATED PRODUCTS PRODUCT TLV349x TLV370x TLV340x FEATURES 1.2µA, 1.8V to 5.5V Push-Pull Comparator 560nA, 2.5V to 16V Push-Pull CMOS Output Comparator 550nA, 2.5V to 16V Open-Drain Comparator OUT V− IN+ 1 2 3 TLV3011 TLV3012 6 5 4 V+ REF IN− Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2004, Texas Instruments Incorporated www.ti.com ABSOLUTE MAXIMUM RATINGS(1) Supply Voltage .................................................................................... +7V Signal Input Terminals, Voltage(2) ........................... –0.5V to (V+) + 0.5V Current(2) .................................................. ±10mA Output Short-Circuit(3) .............................................................. Continuous Operating Temperature .................................................. –55°C to +150°C Storage Temperature ..................................................... –55°C to +150°C Junction Temperature .................................................................... +150°C Lead Temperature (soldering, 10s) ............................................... +300°C ESD Rating (Human Body Model) .................................................. 2000V NOTE: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. (2) Input terminals are diode-clamped to the power-supply rails. In put signals that can swing more than 0.5V beyond the supply rails should be current limited to 10mA or less. (3) Short-circuit to ground. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet. PIN CONFIGURATIONS Top View TLV3011AIDBV OUT V− IN+ 1 2 3 6 5 4 V+ REF IN− OUT V− IN+ 1 2 3 TLV3012AIDBV 6 5 4 V+ REF IN− SOT23-6 TLV3011AIDCK ALR AJX SC70-6 1 2 3 6 5 4 SOT23-6 TLV3012AIDCK ALS ALT OUT V− IN+ V+ REF IN− OUT V− IN+ 1 2 3 6 5 4 V+ REF IN− SC70-6 NOTE: Pin 1 is determined by orienting package marking as shown. 2 TLV3011, TLV3012 www.ti.com SBOS300B ELECTRICAL CHARACTERISTICS: VS = +1.8V to +5.5V Boldface limits apply over the specified temperature range, TA = –40°C to +125°C. At TA = +25°C, VOUT = VS, unless otherwise noted; for TLV3011, RPULL-UP = 10kΩ connected to VS. TLV3011, TLV3012 PARAMETER OFFSET VOLTAGE Input Offset Voltage vs Temperature vs Power Supply INPUT BIAS CURRENT Input Bias Current Input Offset Current INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection Ratio VOS dVOS/dT PSRR CONDITION VCM = 0V, IO = 0V TA = –40°C to +125°C VS = 1.8V to 5.5V VCM = VS/2 VCM = VS/2 (V–) – 0.2V 60 54 MIN TYP 0.5 MAX 12 1000 ±10 ±10 (V+) + 0.2V 74 62 1013 2 1013 4 t(PLH) t(PHL) tR tF VOL CL = 10pF CL = 10pF VS = 5V IOUT = –5mA IOUT = 5mA VIN = 5V VOUT dVOUT/dT dVOUT/dILOAD ILOAD dVOUT/dVIN –40°C ≤ TA ≤ 125°C 0mA < ISOURCE ≤ 0.5mA 0mA < ISINK ≤ 0.5mA 1.8V ≤ VIN ≤ 5.5V f = 0.1Hz to 10Hz 1.230 1.242 40 0.36 6.6 0.5 10 1.254 ±1 100 1 V % ppm/°C mV/mA mV/mA mA µV/V mVPP 5.5 5.5 5 V V µA °C °C °C °C/W °C/W f = 10kHz, VSTEP = 1V Input Overdrive = 10mV Input Overdrive = 100mV Input Overdrive = 10mV Input Overdrive = 100mV 12 6 13.5 6.5 See Note 1 100 100 UNITS mV µV/°C µV/V pA pA ±12 100 ±1 ±1 IB IOS VCM CMRR VCM = –0.2V to (V+) – 1.5V VCM = –0.2V to (V+) + 0.2V V dB dB Ω pF Ω pF µs µs µs µs ns ns INPUT IMPEDANCE Common-Mode Differential SWITCHING CHARACTERISTICS Propagation Delay Time, Low-to-High Propagation Delay Time, High-to-Low Rise Time, TLV3011 Rise Time, TLV3012 Fall Time OUTPUT Voltage Output Low from Rail Voltage Output High From Rail, TLV3012 Short-Circuit Current, TLV3012 VOLTAGE REFERENCE Initial Accuracy Temperature Drift Load Regulation Sourcing Sinking Output Current Line Regulation NOISE Reference Voltage Noise POWER SUPPLY Specified Voltage Operating Voltage Range Quiescent Current TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance, θJA SOT23-6 SC70-6 NOTE: (1) tR dependent on RPULL-UP and CLOAD. 160 90 See Typical Characteristics 200 200 mV mV 100 0.2 VS IQ VS = 5V, VO = High 1.8 1.8 2.8 –40 –55 –55 200 250 +125 +150 +150 TLV3011, TLV3012 SBOS300B www.ti.com 3 TYPICAL CHARACTERISTICS At TA = +25°C, VS = +1.8V to +5.5V, RPULL-UP = 10kΩ, and Input Overdrive = 100mV, unless otherwise noted. QUIESCENT CURRENT vs TEMPERATURE 3.8 3.6 Quiescent Current (µA) Quiescent Current (µA) QUIESCENT CURRENT vs OUTPUT SWITCHING FREQUENCY 8 7 6 5 4 3 2 1 0 VS = 1.8V TLV3011 RPULL-UP = 1MΩ VS = 3V VS = 5V 3.4 3.2 3.0 2.8 2.6 2.4 2.2 2.0 –50 –25 0 25 50 75 100 125 Temperature (°C) 1 10 100 1k 10k Output Transition Frequency (Hz) QUIESCENT CURRENT vs OUTPUT SWITCHING FREQUENCY 14 TLV3012 12 VS = 5V INPUT BIAS CURRENT vs TEMPERATURE 45 40 Quiescent Current (µA) 10 VS = 3V 8 6 4 2 0 1 10 100 1k 10k 100k Output Transition Frequency (Hz) VS = 1.8V Input Bias Current (pA) 35 30 25 20 15 10 5 0 –5 –50 –25 0 25 50 75 100 125 Temperature (°C) OUTPUT LOW vs OUTPUT CURRENT 0.25 0.25 OUTPUT HIGH vs OUTPUT CURRENT TLV3012 VDD = 3V 0.20 VS = 1.8V VS = 3 V VS – VOH (V) 0.20 VDD = 1.8V 0.15 VOL (V) 0.15 V S = 5V 0.10 0.10 VDD = 5V 0.05 0.05 0 0 2 4 6 8 10 12 Output Current (mA) 0 0 2 4 6 8 10 12 Output Current (mA) 4 TLV3011, TLV3012 www.ti.com SBOS300B TYPICAL CHARACTERISTICS (Cont.) At TA = +25°C, VS = +1.8V to +5.5V, RPULL-UP = 10kΩ, and Input Overdrive = 100mV, unless otherwise noted. 80 70 60 tPLH (µs) PROPAGATION DELAY (tPLH) vs CAPACITIVE LOAD TLV3012 80 70 60 50 PROPAGATION DELAY (tPHL) vs CAPACITIVE LOAD VS = 5 V 40 VS = 3 V 30 20 10 0 0.01 VS = 1.8V tPHL (µs) 50 VS = 3V 40 30 20 10 0 0.01 VS = 5 V VS = 1.8V 0.1 1 10 100 1k 0.1 1 10 100 1k Capacitive Load (nF) Capacitive Load (nF) 20 18 16 14 tPLH (µs) 12 10 8 6 4 0 PROPAGATION DELAY (tPLH) vs INPUT OVERDRIVE 20 18 16 PROPAGATION DELAY (tPHL) vs INPUT OVERDRIVE VS = 5V tPHL (µs) 14 12 VS = 1.8V 10 8 6 4 VS = 5V 0 10 20 30 40 50 60 70 80 90 100 VS = 3V VS = 3V VS = 1.8V 10 20 30 40 50 60 70 80 90 100 Input Overdrive (mV) Input Overdrive (mV) 8.0 7.5 7.0 PROPAGATION DELAY (tPLH) vs TEMPERATURE 8.0 7.5 VS = 1.8V PROPAGATION DELAY (tPHL) vs TEMPERATURE 7.0 6.5 tPHL (µs) VS = 1.8V VS = 3V 6.5 tPLH (µs) VS = 3V 6.0 5.5 5.0 4.5 4.0 –50 –25 0 25 50 75 100 125 Temperature (°C) VS = 5V 6.0 5.5 VS = 5V 5.0 4.5 4.0 –50 –25 0 25 50 75 100 125 Temperature (°C) TLV3011, TLV3012 SBOS300B www.ti.com 5 TYPICAL CHARACTERISTICS (Cont.) At TA = +25°C, VS = +1.8V to +5.5V, RPULL-UP = 10kΩ, and Input Overdrive = 100mV, unless otherwise noted. PROPAGATION DELAY (tPLH) VS = ±2.5V VIN+ PROPAGATION DELAY (tPHL) VS = ±2.5V 500mV/div VIN– 500mV/div VIN– VIN+ TLV3012 VOUT 2V/div VOUT 2µs/div 2V/div TLV3011 2µs/div PROPAGATION DELAY (tPLH) VS = ±0.9V VIN+ PROPAGATION DELAY (tPHL) VS = ±0.9V 500mV/div VIN– 500mV/div VIN– VIN+ 2V/div 2V/div VOUT VOUT 2µs/div 2µs/div REFERENCE VOLTAGE vs OUTPUT LOAD CURRENT (Sourcing) 1.24205 1.24200 Reference Voltage (V) REFERENCE VOLTAGE vs OUTPUT LOAD CURRENT (Sinking) 1.250 1.249 Reference Voltage (V) 1.24195 1.24190 1.24185 1.24180 1.24175 1.24170 1.24165 1.24160 0 0.2 0.4 0.6 0.8 1.0 1.2 Output Load Current, Sourcing (mA) 1.248 1.247 1.246 1.245 1.244 1.243 1.242 1.241 0 0.2 0.4 0.6 0.8 1.0 1.2 Output Load Current, Sinking (mA) 6 TLV3011, TLV3012 www.ti.com SBOS300B TYPICAL CHARACTERISTICS (Cont.) At TA = +25°C, VS = +1.8V to +5.5V, RPULL-UP = 10kΩ, and Input Overdrive = 100mV, unless otherwise noted. REFERENCE VOLTAGE vs TEMPERATURE 1.250 1.245 Reference Voltage (V) SHORT-CIRCUIT CURRENT vs SUPPLY VOLTAGE 140 TLV3012 120 1.240 1.235 1.230 1.225 1.220 1.215 1.210 –100 Short-Circuit Current (mA) 100 Sink 80 60 40 20 0 Source –50 0 50 100 150 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Temperature (°C) Supply Voltage (V) REFERENCE VOLTAGE DISTRIBUTION 500 450 400 Reference Voltage (V) 350 300 250 200 150 100 50 0 1.230 1.232 1.234 1.236 1.238 1.240 1.242 1.244 1.246 1.248 1.250 1.252 Volts TLV3011, TLV3012 SBOS300B 1.254 www.ti.com 7 APPLICATIONS INFORMATION The TLV3011 is a low-power, open-drain comparator with on-chip 1.242V series reference. The open-drain output allows multiple devices to be driven by a single pull-up resistor to accomplish an OR function, making the TLV3011 useful for logic applications. The TLV3012 comparator with on-chip 1.242V series reference has a push-pull output stage optimal for reduced power budget applications and features no shoot-through current. A typical supply current of 2.8µA and tiny packaging combine with 1.8V supply requirements to make the TLV3011 and TLV3012 optimal for battery and portable designs. may be added by connecting a small amount of feedback to the positive input. Figure 2 shows a typical topology used to introduce hysteresis, described by the equation: V + × R1 R1 + R 2 VHYST = V+ 5.0V RPULL-UP(1) TLV301x VOUT VIN BOARD LAYOUT Typical connections for the TLV3011 and TLV3012 are shown in Figure 1. The TLV3011 is an open-drain output device. A pull-up resistor must be connected between the comparator output and supply to enable operation. To minimize supply noise, power supplies should be capacitively decoupled by a 0.01µF ceramic capacitor in parallel with a 10µF electrolytic capacitor. Comparators are sensitive to input noise, and precautions such as proper grounding (use of ground plane), supply bypassing, and guarding of high-impedance nodes will minimize the effects of noise and help to ensure specified performance. V+ REF R2 560kΩ R1 39kΩ VREF VHYST = 0.38V NOTE: (1) Use RPULL-UP with the TLV3011 only. FIGURE 2. Adding Hysteresis. VHYST will set the value of the transition voltage required to switch the comparator output by increasing the threshold region, thereby reducing sensitivity to noise. APPLICATIONS 0.01µF 10µF BATTERY LEVEL DETECT RPULL-UP(1) 10kΩ VOUT VIN– VIN+ 4 3 5 REF 6 TLV301x 2 1 V– The low power consumption and 1.8V supply voltage of the TLV3011 make it an excellent candidate for battery-powered applications. Figure 3 shows the TLV3011 configured as a low battery level detector for a 3V battery. Battery − Okay Trip Voltage = 1.242 R1 + R 2 R2 NOTE: (1) Use RPULL-UP with the TLV3011 only. FIGURE 1. Basic Connections of the TLV3011 and TLV3012. OPEN-DRAIN OUTPUT (TLV3011) The open-drain output of the TLV3011 is useful in logic applications. The value of the pull-up resistor and supply voltage used will affect current consumption due to additional current drawn when the output is in a low state. This effect can be seen in the typical curve Quiescent Current vs Output Switching Frequency. R1 1MΩ + − R2 2MΩ TLV301x 1.242V REF RPULL-UP(1) Battery Okay EXTERNAL HYSTERESIS Comparator inputs have no noise immunity within the range of specified offset voltage (±12mV). For noisy input signals, the comparator output may display multiple switching as input signals move through the switching threshold. The typical comparator threshold of the TLV3011 and TLV3012 is ±0.5mV. To prevent multiple switching within the comparator threshold of the TLV3011 or TLV3012, external hysteresis When the battery voltage drops below 1.9V, the battery-okay output will go low. NOTE: (1) Use RPULL-UP with the TLV3011 only. FIGURE 3. TLV3011 Configured as a Low Battery Level Detector. 8 TLV3011, TLV3012 www.ti.com SBOS300B POWER-ON RESET The reset circuit shown in Figure 4 provides a time delayed release of reset to the MSP430 microcontroller. Operation of the circuit is based on a stabilization time constant of the supply voltage, rather than on a predetermined voltage value. The negative input is a reference voltage created by the internal voltage reference. The positive input is an RC circuit that provides a power-up delay. When power is applied, the output of the comparator is low, holding the processor in the reset condition. Only after allowing time for the supply voltage to stabilize does the positive input of the comparator become higher than the negative input, resulting in a high output state, releasing the processor for operation. The stabilization time required for the supply voltage is adjustable by the selection of the RC component values. Use of a lower-valued resistor in this portion of the circuit will not increase current consumption because no current flows through the RC circuit after the supply has stabilized. The reset delay needed depends on the power-up characteristics of the system power supply. R1 and C1 are selected to allow enough time for the power supply to stabilize. D1 provides rapid reset if power is lost. In this example, the R1 • C1 time constant is 10mS. RELAXATION OSCILLATOR The TLV3012 can be configured as a relaxation oscillator as in Figure 5 to provide a simple and inexpensive clock output. The capacitor is charged at a rate of T = 0.69RC. It also discharges at a rate of 0.69RC. Therefore, the period is T = 1.38RC. R1 may be a different value than R2. VC 2/3 (V+) 1/3 (V+) V+ T1 T2 C 1000pF V+ R1 1MΩ VOUT t V+ DI R1 1MΩ C1 10nF 1.242V TLV301x REF RPULL-UP(1) 10kΩ MSP430 TLV3012 R2 1MΩ V+ R2 1MΩ R2 1MΩ t F = 724Hz RESET NOTE: (1) Use RPULL-UP with the TLV3011 only. FIGURE 4. The TLV3011 or TLV3012 Configured as a Power Up Reset Circuit for the MSP430. FIGURE 5. TLV3012 Configured as a Relaxation Oscillator. TLV3011, TLV3012 SBOS300B www.ti.com 9 PACKAGE OPTION ADDENDUM www.ti.com 16-Mar-2007 PACKAGING INFORMATION Orderable Device TLV3011AIDBVR TLV3011AIDBVRG4 TLV3011AIDBVT TLV3011AIDBVTG4 TLV3011AIDCKR TLV3011AIDCKRG4 TLV3011AIDCKT TLV3011AIDCKTG4 TLV3012AIDBVR TLV3012AIDBVRG4 TLV3012AIDBVT TLV3012AIDBVTG4 TLV3012AIDCKR TLV3012AIDCKRG4 TLV3012AIDCKT TLV3012AIDCKTG4 (1) Status (1) ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE Package Type SOT-23 SOT-23 SOT-23 SOT-23 SC70 SC70 SC70 SC70 SOT-23 SOT-23 SOT-23 SOT-23 SC70 SC70 SC70 SC70 Package Drawing DBV DBV DBV DBV DCK DCK DCK DCK DBV DBV DBV DBV DCK DCK DCK DCK Pins Package Eco Plan (2) Qty 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 3000 Green (RoHS & no Sb/Br) 3000 Green (RoHS & no Sb/Br) 250 250 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Lead/Ball Finish CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU MSL Peak Temp (3) Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM 3000 Green (RoHS & no Sb/Br) 3000 Green (RoHS & no Sb/Br) 250 250 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) 3000 Green (RoHS & no Sb/Br) 3000 Green (RoHS & no Sb/Br) 250 250 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) 3000 Green (RoHS & no Sb/Br) 3000 Green (RoHS & no Sb/Br) 250 250 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 16-Mar-2007 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 18-Oct-2007 TAPE AND REEL BOX INFORMATION Device Package Pins Site Reel Diameter (mm) 180 180 180 180 Reel Width (mm) 8 8 8 8 A0 (mm) B0 (mm) K0 (mm) P1 (mm) 4 4 4 4 W Pin1 (mm) Quadrant 8 8 8 8 Q3 Q3 Q3 Q3 TLV3011AIDBVR TLV3011AIDBVT TLV3012AIDBVR TLV3012AIDBVT DBV DBV DBV DBV 6 6 6 6 SITE 21 SITE 21 SITE 21 SITE 21 3.23 3.23 3.23 3.23 3.17 3.17 3.17 3.17 1.37 1.37 1.37 1.37 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 18-Oct-2007 Device TLV3011AIDBVR TLV3011AIDBVT TLV3012AIDBVR TLV3012AIDBVT Package DBV DBV DBV DBV Pins 6 6 6 6 Site SITE 21 SITE 21 SITE 21 SITE 21 Length (mm) 214.0 214.0 214.0 214.0 Width (mm) 199.0 199.0 199.0 199.0 Height (mm) 55.0 55.0 55.0 55.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers RFID Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated