TMS570LS04 Hercules Development Kit (HDK)
User's Guide
Literature Number: SPNU569
September 2012
Contents
....................................................................................................................................... 4
Introduction ........................................................................................................................ 5
1.1
Scope of Document ......................................................................................................... 5
1.2
TMS570LS04 HERCULES Development Kit (HDK) Features ........................................................ 5
1.3
HDK Board Block Diagram ................................................................................................ 6
1.4
TMS570LS04 HDK Contents .............................................................................................. 6
1.5
HDK Specifications ......................................................................................................... 7
1.6
Basic Operation ............................................................................................................. 7
1.7
Memory Map ................................................................................................................. 7
1.8
Power Supply ................................................................................................................ 7
Physical Description ............................................................................................................ 8
2.1
Board Layout ................................................................................................................ 8
2.2
Connectors ................................................................................................................... 9
2.2.1 20-Pin ARM JTAG Header ........................................................................................ 9
2.2.2 20-Pin Compact TI JTAG Header .............................................................................. 10
2.2.3 CAN Interface ..................................................................................................... 10
2.2.4 J4, XDS100V2 USB JTAG Interface ........................................................................... 11
2.2.5 P1, +5 V to +12 V Input .......................................................................................... 11
2.2.6 Virtual COM Port Interface ...................................................................................... 12
2.2.7 Daughter Card Interface ......................................................................................... 12
2.3
LEDs ........................................................................................................................ 16
2.4
Emulator and Pin Multiplexing Selection DIP Switch ................................................................. 16
2.5
Jumpers ..................................................................................................................... 17
2.6
S3, Power-On Reset Switch ............................................................................................. 17
2.7
S2, System Reset Switch ................................................................................................ 17
2.8
S4, Pushbutton for Clock Failure Test .................................................................................. 17
Operation Notices .............................................................................................................. 18
A.1
Support Resources ........................................................................................................ 18
Preface
1
2
A
2
Contents
SPNU569 – September 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
List of Figures
1-1.
TMS570LS04 HDK Board Block Diagram ............................................................................... 6
2-1.
TMS570LS04 HDK Board
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
.................................................................................................
Connectors on TMS570LS04 HDK Table ...............................................................................
CAN Bus Termination .....................................................................................................
J1, J2 Screw Terminal Block for CAN Bus .............................................................................
+12 V Input Jack ...........................................................................................................
J9, J10 and J11 Connectors .............................................................................................
DIP Switch Settings .......................................................................................................
8
9
11
11
12
13
16
List of Tables
............................................................................................
1-1.
TMS570LS0432 Memory Map
1-2.
Power Supply Selection .................................................................................................... 7
1-3.
Power Test Points
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.
2-9.
2-10.
7
.......................................................................................................... 7
Connectors on HDK Board ................................................................................................ 9
20-Pin ARM JTAG Header ............................................................................................... 10
20-Pin CTI JTAG Header ................................................................................................. 10
Expansion Connector P2 (J9, Right, TopView) ........................................................................ 13
Expansion Connector P1 (J9, Left, TopView) ......................................................................... 14
Expansion Connector P3 (J11, Bottom One, TopView) .............................................................. 15
Demo LEDs ................................................................................................................ 16
Other LEDs as Indicator .................................................................................................. 16
S5 DIP Switch Functions ................................................................................................. 16
Jumpers ..................................................................................................................... 17
SPNU569 – September 2012
Submit Documentation Feedback
List of Figures
Copyright © 2012, Texas Instruments Incorporated
3
Preface
SPNU569 – September 2012
Read This First
About This Manual
This document describes the board level operations of the TMS570LS04 Hercules™ Development Kit
(HDK). The HDK is based on the Texas Instruments TMS570LS0432 Microcontroller. The TMS570LS04
HDK is a table top card that allows engineers and software developers to evaluate certain characteristics
of the TMS570LS0432 microcontroller to determine if the microcontroller meets the designer application
requirements. Evaluators can create software to execute on board or expand the system in a variety of
ways.
Notational Conventions
This document uses the following conventions.
The TMS570LS04 HDK will sometimes be referred to as the HDK.
Program listings, program examples, and interactive displays are shown in a special italic typeface. Here
is a sample program listing:
• equations
• !rd = !strobe&rw;
Information About Cautions
This book may contain cautions.
This is an example of a caution statement.
A caution statement describes a situation that could potentially damage your software, or hardware, or
other equipment. The information in a caution is provided for your protection. Please read each caution
carefully.
Related Documentation From Texas Instruments
Information regarding this device can be found at the following Texas Instruments website:
http://www.ti.com/rm4
4
Read This First
SPNU569 – September 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Chapter 1
SPNU569 – September 2012
Introduction
The TMS570LS0432 HDK is a low cost and easy to use hardware and software platform for evaluating the
functionality of the Texas Instruments TMS570LS0432 microcontroller family. Project collateral,
schematics and PCB layouts discussed in this application report can be downloaded from the following
URL:
(http://processors.wiki.ti.com/index.php/TMS570LS04x_HDK_Kit).
1.1
Scope of Document
This user guide will list the contents of the development kit, point out the features of the major
components, and provide the instructions necessary to verify your development kit is in working order. Any
additional usage instructions or details fall outside the scope of this document. Additional resources are
listed at the end of this user guide.
1.2
TMS570LS04 HERCULES Development Kit (HDK) Features
The HDK comes with a full complement of on board devices that suit a wide variety of application
environments. Key features include:
• A Hercules TMS570LS0432 100-pin QFP microcontroller
• Integrated USB JTAG emulator (XDS100v2)
• External JTAG headers ( ARM® 20 pin and TI compact 20-pin CTI)
• One DIP switch to select pull-up or pull-down for JTAG nTRST
• Two CAN transceivers (SN65HVDA541Q1) and screw terminal blocks
• One ambient light sensor
• One ambient temperature sensor
• Microcontroller’s serial communications interface (SCI) universal asynchronous receiver/transmitter
(UART) accessible through a USB virtual COM port
• Four user programmable white LEDs
• One user programmable pushbutton
• Three expansion connectors for hardware prototyping
• Reset and power-on reset pushbuttons (nRST and nPORRST)
• One pushbutton simulating external oscillator failure
• One Jumper to select clock source for MCU: crystal or crystal oscillator
• One crystal socket (HC-18)
• One SD card slot (SPI mode)
• Current measurement capability for 3.3 V IO, 3.3 V analog-to digital converter (ADC) and, 1.2 V core
voltage
• May be powered by USB or an external power supply in case additional power is required (for
expansion boards)
• Accepts an external power supply between +5 V and +12 V
SPNU569 – September 2012
Submit Documentation Feedback
Introduction
Copyright © 2012, Texas Instruments Incorporated
5
HDK Board Block Diagram
HDK Board Block Diagram
ENET
RJ45
Ext JTAG
CTI
JTAG
Power
Select
FTDI
2332
CPLD
3.3V I/O
XDS100V2
PWR
nRST
nPOR
USB
EMU
1.2V Core
1.3
www.ti.com
CAN/LIN/GIO/
HET
EXP Conn1
TMS570LS0432
80MHz
Clock
Select
EXP Conn3
CAN
PHY
CAN1
Light
Sensor
SPI/ADC
EXP
Conn2
JTAG
Clock
Reset
GIO
Button
Temp
Sensor
CAN
PHY
CAN2
Figure 1-1. TMS570LS04 HDK Board Block Diagram
1.4
TMS570LS04 HDK Contents
The kit contains everything needed to develop and run applications for TMS570LS04 microcontrollers
including:
• Cables and Accessories:
– 12 V power supply with power adapters for US, or Europe
– Type A to mini B USB cable for using on board XDS100V2 JTAG emulator
– Flashlight for light sensor demo
• CCS DVD Containing:
– Texas Instruments’ Code Composer Studio™ Integrated Development Environments (IDE)
• Hercules DVD Containing:
– Hercules Safety Demos
– Hardware Abstraction Layer Code Generator (HALCoGen)
– Training Videos
– Device Documentation
6
Introduction
SPNU569 – September 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
HDK Specifications
www.ti.com
1.5
HDK Specifications
•
•
•
1.6
Board supply voltage: 5 V to 12 V DC
Board supply current: 130 mA typ (fully active, CPU at 100 MHz)
Dimensions: 4.90” x 4.30” x 0.85” (LxWxH)
Basic Operation
The HDK is designed to work with TI’s Code Composer Studio and other third party ARM IDEs. The IDEs
communicate with the board through the embedded emulator or an external JTAG emulator. To get
started, follow the instructions in the Quick Start Guide to install Hercules specific software. This process
will install all of the necessary development tools, documentation, and drivers.
1.7
Memory Map
The TMS570LS04 family of MCUs have a large byte addressable address space. Table 1-1 shows the
address space of a TMS570LS0432 microcontroller on the left with specific details of how each region is
used on the right. On-chip Flash memory starts at the beginning of the address space where the exception
vector table is located.
Table 1-1. TMS570LS0432 Memory Map
1.8
Start Address
End Address
HDK
0x0000 0000
0x0005 FFFF
384KB Flash
0x0800 0000
0x0800 7FFF
32KB RAM
0x0840 0000
0x0840 7FFF
RAM-ECC
Power Supply
The HDK board operates from either +5V supplied from the USB connector (J4) or +5 V to +12 V supplied
from the power supply connected to the main power input (P1), a 2.5 MM, barrel-type plug. Internally, the
power input is converted into +1.2 V, +3.3 V using Texas Instruments voltage regulators. The +1.2 V
supply is used for the MCU core while the +3.3 V supply is used for the MCU's I/O buffers and other
component on the board.
The power used for operation is determined by the options listed in Table 1-2.
Table 1-2. Power Supply Selection
Power Used for
the Board
USB VBUS (+5 V)
(USB Cable is Plugged or Not)
Power From P1(5 V to 12 V)
(Power Cable is Plugged or Not)
From P1
ON
ON
From P1
OFF
ON
From VBUS
ON
OFF
There are multiple power test points on the HDK board. The three main test point pairs provide a
convenient mechanism to check the HDK’s current for each supply. Table 1-3 shows the voltages for each
test point and what the supply is used for.
Table 1-3. Power Test Points
Test Point Pair
Voltage
Voltage Use
TP11 and TP12
1.2 V
MCU core
TP3 and TP4
3.3 V
MCU IO and logic
TP22 and TP23
3.3 V
MCU ADC power
SPNU569 – September 2012
Submit Documentation Feedback
Introduction
Copyright © 2012, Texas Instruments Incorporated
7
Chapter 2
SPNU569 – September 2012
Physical Description
This chapter describes the physical layout of the TMS570LS04 HDK board and its interfaces.
2.1
Board Layout
The TMS570LS04 HDK board a 4.9 x 4.3 inch (125 x 109 mm.) six layer printed circuit board that is
powered by either +5 V USB power from an external +5 V to +12 V only power supply or by USB VBUS.
Figure 2-1 shows the layout of the TMS570LS04 HDK board.
TMS570LS
0432
Figure 2-1. TMS570LS04 HDK Board
8
Physical Description
SPNU569 – September 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Connectors
www.ti.com
2.2
Connectors
The HDK board has ten interfaces to various peripherals. These interfaces are described in Table 2-1.
J4
P1
J15
J5
J3
J10
J9
TMS570LS
0432
J11
J1
J2
Figure 2-2. Connectors on TMS570LS04 HDK Table
Table 2-1. Connectors on HDK Board
Connector
Size
J1
3, 2,54mm
Function
DCAN1
J2
3, 2.54mm
DCAN2
J3
10x2, 2.54mm
J4
4pin, Mini-B USB
ARM 20-pin JTAG header
J5
10x2, 2mm
Compact TI 20-pin JTAG header
XDS100V2 USB
J9
33x2, 2mm
Exp P1, SPI1, ADC, nPORRST
J10
33x2, 2mm
EXP P2, SPI2, nRST, ECLK, nERROR
J11
40x2, 2mm
EXP P3, GIO, CAN, LIN, EQEP, NHET, SPI3
J15
Micro SD slot
SD card
P1
2.5mm
+12 V In
2.2.1 20-Pin ARM JTAG Header
In addition to on board XDS100V2 JTAG. One 20-pin ARM JTAG header is added for using an external
emulator. This is the standard interface used by JTAG emulators to interface to ARM microcontrollers. The
pinout of the connector is shown in Table 2-2.
SPNU569 – September 2012
Submit Documentation Feedback
Physical Description
Copyright © 2012, Texas Instruments Incorporated
9
Connectors
www.ti.com
Table 2-2. 20-Pin ARM JTAG Header
Signal Name
Pin Number
Pin Number
Vref
1
2
Signal Name
VCC
nTRST
3
4
GND
TDI
5
6
GND
TMS
7
8
GND
TCK
9
10
GND
RTCK
11
12
GND
TDO
13
14
GND
nRST
15
16
GND
NC
17
18
GND
NC
19
20
GND
2.2.2 20-Pin Compact TI JTAG Header
We also implemented a compact TI JTAG header (CTI) on the board. This is the standard interface used
by TI and Spectrum Digital JTAG emulators. The pinout for the connector is shown in Table 2-3.
Table 2-3. 20-Pin CTI JTAG Header
Signal Name
Pin Number
Pin Number
Signal Name
TMS
1
2
nTRST
TDI
3
4
TDIS
VTRef
5
6
KEY
TDO
7
8
GND
RTCLK
9
10
GND
TCLK
11
12
GND
NA
13
14
NA
SYSRSTn
15
16
GND
NA
17
18
NA
NA
19
20
GND
2.2.3 CAN Interface
The TMS570LS0432 has two DCAN interfaces which provide a high-speed serial interface. Two 3 pin
screw terminal blocks, J1 and J2, are used to interface with 12 the DCAN bus. The pinouts for this
connector are shown in Figure 2-3. H means CAN High (CAN H), and L means CAN Low (CAN L).
CAN Bus termination is used to minimize signal reflection on the bus. ISO-11898 requires that the CAN
bus have a nominal characteristic line impedance of 120 Ω. Therefore, the typical terminating resistor
value for each end of the bus is 120 Ω. A split termination method is used to help increase EMC
performance. Split termination is a concept that is growing in popularity because emission reduction can
be achieved very easily. Split termination is a modified standard termination in which the single 120 Ω
resistor on each end of the bus is split into two 60 Ω resistors, with a bypass capacitor tied between the
resistors and to ground. The two resistors should match as close as possible.
10
Physical Description
SPNU569 – September 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Connectors
www.ti.com
Figure 2-3. CAN Bus Termination
J1
H
J2
L
H
L
Figure 2-4. J1, J2 Screw Terminal Block for CAN Bus
2.2.4 J4, XDS100V2 USB JTAG Interface
The USB connector J4 is used to connect to the host development system which is running the software
development IDE (CCS for example).
Before the board is shipped, the XDS100V2 port1 is configured as JTAG, and port2 is configured as SCI.
The CPLD is also programmed to route the JTAG signals to the MCU.
There is a circuitry to detect an external JTAG emulator. If an external emulator is plugged onto the
header J3 and J5, the DS1 LED will turn on, and XDS100V2 JTAG will be disabled.
2.2.5 P1, +5 V to +12 V Input
Connector P1 is the input power connector. This connector brings +5V to +12 V to the HDK board. This is
a 2.5 mm. jack. Figure 2-5 shows this connector as viewed from the card edge.
SPNU569 – September 2012
Submit Documentation Feedback
Physical Description
Copyright © 2012, Texas Instruments Incorporated
11
Connectors
www.ti.com
+12 V
GND
P1
text
text
PC Board
Figure 2-5. +12 V Input Jack
2.2.6 Virtual COM Port Interface
The internal SCI on the TMS570LS0432 device is connected to the second port of the XDS100V2. The
XDS100V2 USB driver makes the second channel of FT2232H appear as a virtual COM port (VCP). This
allows the user to communicate with the USB interface via a standard PC serial emulation port.
2.2.7 Daughter Card Interface
The HDK provides expansion connectors that can be used to accept plug-in daughter cards. The daughter
card allows users to build on their EVM platform to extend its capabilities and provide customer and
application specific I/O. The expansion connectors are for all major interfaces including SPIs, ADCs, GIOs,
NHETs, and EQEP, and so forth.
12
Physical Description
SPNU569 – September 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Connectors
www.ti.com
There are three daughter card interfaces, J9, J10, and J11. These connectors are described in Table 2-4.
J9
J10
J11
Figure 2-6. J9, J10 and J11 Connectors
Table 2-4. Expansion Connector P2 (J9, Right, TopView)
Signal Name
Number
Number
EXP_12V
Pin Number
1
2
Pin Number
Signal Name
GND
EXP_12V
3
4
GND
SPI1ENA/NHET23/NHET30
68
5
6
67
SPI1CLK
SPI1CS[1]
93
7
8
73
SPI1CS[0]
SPI1CS[3]/NHET26
39
9
10
27
SPI1CS[2]/NHET19/NHET20
SPI1SIMO
65
66
SPI1SOMI
11
12
GND
13
14
GND
NC
15
16
NC
NC
17
18
NC
NC
19
20
NC
NC
21
22
NC
NC
23
24
NC
NC
25
26
NC
NC
27
28
NC
GND
29
30
GND
AD1IN[1]
49
31
32
42
AD1IN[0]
AD1IN[3]
52
33
34
51
AD1IN[2]
AD1IN[5]
55
35
36
54
AD1IN[4]
SPNU569 – September 2012
Submit Documentation Feedback
Physical Description
Copyright © 2012, Texas Instruments Incorporated
13
Connectors
www.ti.com
Table 2-4. Expansion Connector P2 (J9, Right, TopView) (continued)
Signal Name
Pin Number
Number
Number
Pin Number
43
37
38
56
39
40
41
42
43
44
45
46
NC
47
48
AGND
49
50
AD1IN[7]
GND
AD1IN[17]
41
NC
AD1IN[21]
45
Signal Name
AD1IN[6]
GND
40
AD1IN[16]
NC
44
AD1IN[20]
NC
GND
AD1IN[9]
48
51
52
57
AD1IN[8]
AD1IN[11]
53
50
AD1IN[10]
53
54
NC
55
56
NC
NC
57
58
NC
GND
59
60
NC
61
62
NC
63
64
NC
65
66
GND
AD1EVT/NHET28
58
EXP_12V
31
nPORRST
Table 2-5. Expansion Connector P1 (J9, Left, TopView)
Signal Name
Pin Number
EXP_12V
14
Number
Number
Pin Number
Signal Name
1
2
ECLK
84
3
4
GND
nRST
81
5
6
NC
82
nERROR
NC
7
8
NC
NC
9
10
NC
NC
11
12
NC
NC
13
14
NC
NC
15
16
NC
NC
17
18
NC
NC
19
20
NC
NC
21
22
NC
NC
23
24
NC
NC
25
26
NC
NC
27
28
NC
GND
29
30
GND
NC
31
32
NC
NC
33
34
NC
NC
35
36
NC
NC
37
38
NC
GND
39
40
GND
NC
41
42
NC
NC
43
44
NC
NC
45
46
NC
NC
47
48
NC
NC
49
50
NC
NC
51
52
NC
NC
53
54
NC
NC
55
56
NC
GND
57
58
GND
Physical Description
SPNU569 – September 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Connectors
www.ti.com
Table 2-5. Expansion Connector P1 (J9, Left, TopView) (continued)
Signal Name
Pin Number
Number
Number
SPI2_SOMI
69
59
60
SPI2_SIMO
70
61
62
SPI2_CS0
23
63
64
65
66
EXP_12V
Pin Number
Signal Name
NC
NC
71
SPI2_CLK
GND
Table 2-6. Expansion Connector P3 (J11, Bottom One, TopView)
Signal Name
Pin Number
EXP_12V
EXP_12V
Number
Number
1
2
Pin Number
Signal Name
GND
3
4
LINRX
94
5
6
95
GND
LINTX
CAN1RX
63
7
8
62
CAN1TX
CAN2RX
92
91
CAN2TX
9
10
NC
11
12
NC
NC
13
14
NC
NC
15
16
NC
NC
17
18
NC
GIOA[1]/SPI3CS2
2
19
20
1
GIOA[0]
GIOA[3]/SPI3CS3
8
21
22
5
GIOA[2]
GIOA[5]/EXTCLKIN
10
23
24
9
GIOA[4]
GIOA[7]/NHET29
18
25
26
12
GIOA[6]
NC
27
28
NC
NC
29
30
NC
NC
31
32
NC
NC
33
34
NC
GND
35
36
NC
37
38
19
NHET1[0]
NC
39
40
22
NHET1[2]
NC
41
42
25
NHET1[4]
NC
43
44
26
NHET1[6]
NC
45
46
74
NHET1[8]
NC
47
48
83
NHET1[10]
NC
49
50
89
NHET1[12]
NC
51
52
90
NHET1[14]
NC
53
54
97
NHET1[16]
98
NHET1[18]
GND
EQEPA
36
55
56
EQEPI
38
57
58
EQEPB
37
59
60
11
NHET1[22]
EQEPS
93
61
62
64
NHET1[24]
58
ADEVT/NHET28
NC
NC
63
64
GIOA7/NHET29
18
65
66
GIOA6/SPI2CS1/NHET31
12
67
68
69
70
71
72
2
GIOA1/SPI3CS2
73
74
34
SPI3SOMI
GND
GIOA0/SPI3CS3
1
SPI3SIMO
GIOA2/SPI3CS1
5
NC
nRST
75
76
38
SPI3CS0
SPI3ENA
77
78
36
SPI3CLK
EXP_12V
79
80
SPNU569 – September 2012
Submit Documentation Feedback
GND
Physical Description
Copyright © 2012, Texas Instruments Incorporated
15
LEDs
2.3
www.ti.com
LEDs
The TMS570LS04 HDK board has fourteen (14) LEDs. Four of them are under user control. Those LEDs
are controlled and programmed by GIO signals.
LED DS2, DS3, DS4, and DS5 indicate the presence of the power (+1.2 V, +5 V, 3.3 V, and 12 V) on the
board. The LED functions are summarized in Table 2-7 and Table 2-8.
Table 2-7. Demo LEDs
LED Number
Location
Signals
Color
D2
Left Top
GIOA6
White
D4
Left Bottom
GIOA4
White
D5
Right Top
GIOA3
White
D7
Right Bottom
GIOA2
White
Table 2-8. Other LEDs as Indicator
2.4
Number
LED
Color
DS6
nERROR
Red
D9
XDS100V2 SCI RX
Blue
D8
XDS100V2 SCI TX
Blue
D10
XDS100V2 PWRENn
Blue
D1
JTAG TDI
Blue
DS1
External JTAG Emulator Used
Blue
DS5
VCC_1V2
Blue
DS3
VCC_5V
Blue
DS2
VCC_3V3
Blue
DS4
VCC_12V
Blue
Emulator and Pin Multiplexing Selection DIP Switch
There is one 2-position DIP switch (S5) located at 20-pin CTI JTAG header. By default, all of the channels
are set to the “OFF” position.
1 2
1
2
Figure 2-7. DIP Switch Settings
Table 2-9. S5 DIP Switch Functions
Switch
S5:1
(1)
S5:2
(1)
16
OFF Position (left)
ON Position (right)
TI emulator
ARM Emulator
SPI
EQEP
S5:1 indicates slide 1 on the S5 switch, S5:2 indicates slide 2 on the S5.
Physical Description
SPNU569 – September 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Jumpers
www.ti.com
2.5
Jumpers
HDK board has one jumper to select crystal or oscillator for MCU.
Table 2-10. Jumpers
2.6
Switch
Position 1 - 2
Position 2 - 3
JP1
Oscillator Y3
Crystal Y2
S3, Power-On Reset Switch
TMS570LS04 MCU has two resets: Warm Reset (nRST) and Power-On Reset (nPORRST). Switch S3 is
a momentary switch that asserts power on reset to the TMS570LS0432 device. The nPORRST condition
is intended to reset all logic on the device including the test and emulation circuitry.
2.7
S2, System Reset Switch
Switch S2 is used to assert a warm reset to reset the TMS570LS0432 device. Warm reset does not reset
any test or emulation logic. The reset signal from window watchdog will also assert a warm reset to MCU.
The System Reset can be invoked by pushing nRST button, or by RESET signals from XDS100 CPLD,
ARM JTAG SREST, and CTI JTAG SREST.
2.8
S4, Pushbutton for Clock Failure Test
Switch S4 is a momentary switch that will short the OSCIN pin of the crystal to ground through a current
limiting resistor. Pushing this button simulates a crystal failure and causes a CLKDET hardware fault on
MCU. By default this detection will trigger the Error Signaling Module (ESM) to drive the nERROR pin. On
TMS570LS04 HDK, the red LED will then light. The error can be cleared by the nPORRST (S3), cycling
the power to the MCU or via safety software executed on the MCU.
SPNU569 – September 2012
Submit Documentation Feedback
Physical Description
Copyright © 2012, Texas Instruments Incorporated
17
Appendix A
SPNU569 – September 2012
Operation Notices
The user assumes all responsibility and liability for proper and safe handling of the boards. It is the user's
responsibility to take any and all appropriate precautions with regard to electrostatic discharge.
A.1
Support Resources
•
•
•
18
If you have problems or need additional information regarding the embedded emulation please refer to
the XDS100 USB wiki on the TI web site. The URL for this site is:
http://tiexpressdsp.com/index.php?title=XDS100
Code Composer Studio support is available via a forum at: http://community.ti.com/forums/138.aspx
Hercules MCU support is available via a forum at: http://www.ti.com/hercules-support
Operation Notices
SPNU569 – September 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
【Important Notice for Users of this Product in Japan】
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even
if the EVM should fail to perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
【Important Notice for Users of this Product in Japan】
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even
if the EVM should fail to perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
