User's Guide
SBOU202 – October 2018
TMP6EVM User's Guide
The TMP6EVM is a prototype evaluation module (EVM) designed to evaluate the silicon-based TMP6131
thermistor. The TMP6xxx is a family of positive temperature coefficient (PTC) thermistors, which the
resistance increases with temperature. This user's guide describes the characteristics, operation, and use
of the TMP6EVM evaluation board. Throughout this document, the terms evaluation board, evaluation
module, and EVM are synonymous with the TMP6EVM.
Figure 1. TMP6EVM Top View
NOTE: The EVM's SPDT power switch (component S1) is located next to the green VCC_STAT
LED. Use the S1 switch to change between the USB and battery power modes. The switch
position closest to the micro USB receptacle is the USB power mode and the switch position
closest to the corner is the battery power mode. Refer to Figure 1.
NOTE: Important disclaimer: In the standalone demo mode (without GUI), the system is calibrated to
TMP116 on power reset to remove any initial temperature offset between the TMP6 and
TMP116. In the data logging mode with the GUI, no calibration is applied.
Figure 2. TMP6EVM Bottom View
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
1
www.ti.com
1
2
3
4
5
Contents
Overview ..................................................................................................................... 3
EVM Hardware ............................................................................................................... 6
EVM Software Setup ....................................................................................................... 12
EVM Software Overview .................................................................................................. 16
EVM Documentation ....................................................................................................... 19
1
TMP6EVM Top View
List of Figures
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
....................................................................................................... 1
TMP6EVM Bottom View .................................................................................................... 1
Disclaimer Page After Powering Up in Standalone Mode .............................................................. 3
Quick User's Guide Page ................................................................................................... 4
EVM LCD Display Indicating Data Logging Mode ....................................................................... 4
Hardware Included With the EVM Kit ..................................................................................... 5
EVM Block Diagram ......................................................................................................... 6
USB Device Driver Installation ............................................................................................ 6
Daughtercard Required Connections for Using All Three Channels .................................................. 7
Motherboard Required Connections for Using All Three Channels ................................................... 8
EVM 3D Top View ........................................................................................................... 9
EVM 3D Bottom View ....................................................................................................... 9
Primary EVM Display Mode............................................................................................... 11
Secondary EVM Display Mode ........................................................................................... 11
TMP6 EVM GUI Installation Wizard ..................................................................................... 12
TMP6 EVM GUI License Agreement ................................................................................... 13
TMP6 EVM GUI Installation Folder Selection ......................................................................... 13
TMP6 EVM GUI Installation............................................................................................... 14
TMP6 EVM Installation Finish ........................................................................................... 14
Launching the EVM GUI .................................................................................................. 15
Home Page ................................................................................................................. 16
Collateral Page ............................................................................................................. 17
Data Capture................................................................................................................ 18
EVM Schematic ............................................................................................................ 19
Top Layers .................................................................................................................. 20
Top Signal Layer ........................................................................................................... 21
Ground Layer ............................................................................................................... 22
Power Layer ................................................................................................................ 23
Bottom Signal Layer ....................................................................................................... 24
Bottom Layers .............................................................................................................. 25
List of Tables
1
EVM Kit Contents ............................................................................................................ 5
2
Recommended Operating Conditions ..................................................................................... 7
3
EVM Bill of Material ........................................................................................................ 26
Trademarks
Windows is a registered trademark of Microsoft Corporation.
All other trademarks are the property of their respective owners.
2
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Overview
www.ti.com
1
Overview
The TMP6EVM is an evaluation module designed to evaluate the TMP6131 thermistor. The EVM features
the TMP116 high-accuracy local digital temperature sensor (Channel 0), TMP6131 PTC thermistor (Ch1),
and an optional analog channel (Ch2). The EVM can be powered either through a micro USB cable or
with a CR2032 3-V coin cell battery. In standalone mode (when powered with a 5-V USB wall plug or coin
cell battery), the EVM requires no additional hardware or software to begin evaluation. The LCD provides
the readout. In data logging mode (when connected to a computer USB port), the user must open up the
graphical user interface (GUI) to visualize the readouts. When powering up in standalone mode, the user
is presented with a disclaimer the user must accept to proceed with evaluation (as shown in Figure 3).
Following the disclaimer, the user is presented with a quick user's guide Figure 4. When the user has read
the quick user's guide, the user can begin evaluation. The temperature data are updated to the LCD at
approximately 2 Hz. The EVM hosts a MSP430F5528 microcontroller, which is used to interface with both
the digital and analog devices. The sensor section of the PCB may be separated from the main PCB to
support prototyping in a system where the sensor is remotely placed away from the host controller.
NOTE:
Windows will install the necessary drivers the first time the EVM is connected to the
computer USB port. After the driver installation, the user must select the RESET button
(SW3) to switch to the data logging mode. The LCD will display a TI logo as shown in
Figure 5, which indicates that the EVM is in data logging mode and that the user must open
the GUI.
Figure 3. Disclaimer Page After Powering Up in Standalone Mode
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
3
Overview
www.ti.com
Figure 4. Quick User's Guide Page
Figure 5. EVM LCD Display Indicating Data Logging Mode
4
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
Overview
www.ti.com
1.1
EVM Kit Contents
Table 1 lists the contents of the EVM kit, and Figure 6 shows all of the included hardware. Refer to
Section 2.3 for the recommended operation conditions. Contact the nearest Texas Instruments Product
Information Center if any component is missing.
Table 1. EVM Kit Contents
ITEM
QUANTITY
TMP6EVM
1
USB A Male to USB B Micro Male Cable
1
Figure 6. Hardware Included With the EVM Kit
1.2
REACH
CAUTION
This EVM includes a crystal component (CSTCR4M00G15L99-R0) that
contains >0.1% of Lead Titanium Oxide CAS# 12626-81-2 listed in EU REACH
as a Substance of Very High Concern. For more information, contact the
component manufacturer.
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
5
EVM Hardware
2
www.ti.com
EVM Hardware
This section discusses the EVM hardware design.
2.1
EVM Theory of Operation
The EVM consists of two sections that can be separated by breaking the PCB at the perforations. The red
dashed lines in Figure 7 represent the breakable connections on the PCB. The left section contains a
standard USB Type B micro receptor, a coin cell receptor, an ESD protection block, a 3.0-V LDO, a SPDT
switch, a MSP430 microcontroller with an integrated 12-bit SAR Analog-to-Digital Converter (ADC), two
LED indicators, a battery monitor circuit, and a 128x128 LCD display. The right section features the
TMP116 digital temperature sensor, the TMP6131 thermistor divider network, and an optional thermistor
network.
Figure 7. EVM Block Diagram
2.2
Connecting the EVM to a Computer
Figure 8 shows the typical response when connecting the EVM board to a PC USB port for the first time.
Typically, the computer responds with a Found New Hardware, USB device pop-up dialog. The pop-up
window then typically changes to Found New Hardware, USB Human Interface Device. This pop-up
indicates that the device is ready to be used. The EVM uses the human interface device drivers that are
part of the Microsoft Windows® operating system.
Figure 8. USB Device Driver Installation
In some cases, the Windows Add Hardware Wizard is shown. If this prompt occurs, allow the system
device manager to install the human interface drivers by clicking Yes when requested to install drivers.
Windows confirms installation of the drivers with the message shown in Figure 8.
6
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Hardware
www.ti.com
2.3
Operating Conditions
Table 2. Recommended Operating Conditions
PARAMETER
TEST CONDITIONS
MIN
NOM
MAX
UNIT
Operating free-air temperature
Motherboard
–20
25
70
°C
Operating free-air temperature
USB Extension Cable
NA
25
80
°C
Operating free-air temperature
Daughtercard
–40
25
125
°C
The EVM motherboard can only operate up to 70°C due to the LCD display's limitation. To evaluate the
TMP6131 device at its maximum specified operating temperature of 125°C, the user must break off the
breakout section of the EVM. Use the unpopulated pin hole header J4 and a cable (not included in the kit)
to thermally isolate the two EVM sections. The J4 header has five pins (SDA, SCL, GND, OUT0, and
VCC), which is enough to support both the TMP116 and TMP6 devices. This sharing of VCC and GND
between TMP116 and the TMP6 network reduces the total wire count in the breakout mode. However, to
support all three channels (the TMP116, TMP6, and an optional thermistor channel) an additional
connection is needed (OUT1 from J6) as shown in Figure 9 and Figure 10. Note that the pins on J5 are
normally connected. In contrast, the J3 pins are normally open, which is why J3 requires the user to
manually short the pins during breakout mode.
Figure 9. Daughtercard Required Connections for Using All Three Channels
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
7
EVM Hardware
www.ti.com
Figure 10. Motherboard Required Connections for Using All Three Channels
CAUTION
Many components on the EVM are susceptible to damage by electrostatic
discharge (ESD). Customers are advised to observe proper ESD handling
precautions when unpacking and handling the EVM, including the use of a
grounded wrist strap at an approved ESD workstation.
8
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Hardware
www.ti.com
2.4
EVM Features
This section describes some of the hardware features present on the EVM. Refer to Figure 11 and
Figure 12 for the various designators described in this section.
Figure 11. EVM 3D Top View
Figure 12. EVM 3D Bottom View
2.4.1
One Digital Channel
The EVM features one digital temperature sensor channel. The TMP116 digital local temperature sensor
(U4) has an accuracy of ±0.3°C (maximum) from –40°C to 125°C. This high accuracy sensor is used as a
local temperature reference.
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
9
EVM Hardware
2.4.2
www.ti.com
Two Analog Channels
The EVM can support up to two analog channels. The first analog channel is dedicated for the TMP6
device (RT2), and the second channel is an optional channel (RT6). For this EVM, a NTC device is
populated for the second analog channel.
2.4.3
Programming
Push button SW0 and J8 are available for Bootloader (BSL) and Spy-Bi-Wire (SBW) programming,
respectively. To enter to BSL mode, hold down the BSL button while powering up the EVM. To flash the
EVM in BSL mode, the user can use a program like Python Firmware Upgrader GUI.
2.4.4
ESD Protection
The EVM features an ESD protection circuit based on the TPD4E004 device.
2.4.5
LDO
The EVM is powered from the USB rail. The USB 5-V rail is regulated to 3.0 V with the LP2985AIM5X-3.0
device. The 3.0 V powers both the MSP430 microcontroller and the sensors. The sensor supply current
can be monitored by replacing R4 with a current meter.
2.4.6
LED Indicators
There are two LED indicators on the EVM. The green LED (D1) indicates when the EVM is powered (USB
or battery). The orange LED (D3) indicates when the microcontroller is active. The microcontroller only
wakes up twice every second to update the LCD.
2.4.7
RC Filter
The TMP6EVM is designed to support a simple RC low-pass filter (R21 and C15 for Ch1; R22 and C16 for
Ch2). The RC filter can be used to suppress electrical interference and to optimize ADC performance. In
most analog designs, a filter capacitor is recommended. For a typical design, TI recommends a 0.1-μF
external capacitor (TMP6EVM default filter configuration).
2.4.8
VCC/Battery Monitor
The VCC/Battery rail voltage is monitored in this design through a voltage divider network (R19 and R20).
The C11 capacitor is required due to the high source impedance of the divider network.
2.4.9
Reverse-Polarity Protection
The P-channel FET (Q1) is used to prevent accidental reverse-polarity when inserting a coin cell battery.
2.4.10
ADC Ratiometric Measurement
A basic ADC ratiometric measurement technique was employed for the analog channels to suppress the
power supply and ADC reference voltage (Vref) error contributions. This is accomplished by using the
voltage divider bias voltage as the ADC Vref also. The ADC code, which represents the ratio of input
voltage to the Vref, changes with the thermistor resistance as a function of temperature (ideally
independent of the bias voltage). This approach provides great power supply rejection and tolerates Vref
error across different EVMs.
2.4.11
Primary EVM Display Mode
This is the default display mode following the quick user's guide page described earlier. Only the TMP116
(Ch0) and TMP6 (Ch1) temperature readings are displayed, as shown in Figure 13. Briefly (for
approximately half a second) hold down the user switch SW1 to toggle to the next display mode. To go
back to the primary display, just hold down the SW1 again.
10
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Hardware
www.ti.com
Figure 13. Primary EVM Display Mode
2.4.12
Secondary EVM Display Mode
The secondary display contains more detailed information, including channel 1 and channel 2 ADC code
readouts, ADC voltage equivalent (assuming Vref = 3.0 V), VCC/Battery voltage, and offset value relative
to TMP116 used on power reset. In Figure 14, the TMP6 readout corresponds to Ch1 and the NTC
readout corresponds to Ch2.
Figure 14. Secondary EVM Display Mode
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
11
EVM Software Setup
3
www.ti.com
EVM Software Setup
This section discusses how to install the EVM software.
3.1
Operating Systems for the EVM Software
The EVM software is tested on the Microsoft Windows 7 and 10 operating systems (OS) with United
States and European regional settings. The software also functions on other Windows operating systems.
3.2
EVM Software Installation
The EVM software is available through the TMP6EVM product folder on the TI website.
1. Go to the TMP6EVM web page on the TI website and scroll down to the Software section to download
the latest evaluation software.
2. Unzip the downloaded file into a known directory and run the TMP6_EVM_GUI-1.0.0.setupwin_6.1.1.exe file. The EVM software installer then begins the installation process, as shown in
Figure 15.
Figure 15. TMP6 EVM GUI Installation Wizard
12
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Software Setup
www.ti.com
3. Accept the license agreement and follow the on-screen instructions by clicking the Next button to
install the software.
Figure 16. TMP6 EVM GUI License Agreement
4. Click on the Next button to accept the default installation directory.
Figure 17. TMP6 EVM GUI Installation Folder Selection
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
13
EVM Software Setup
www.ti.com
5. The installer will begin as shown in Figure 18.
Figure 18. TMP6 EVM GUI Installation
6. When the installation is finished, click the Finish button. This will launch the GUI application.
Figure 19. TMP6 EVM Installation Finish
14
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Software Setup
www.ti.com
7. The first time the GUI launches, the README file will pop up. Make sure the EVM is now connected to
the computer USB port. Closing the README pop-up will start the data logging chart.
Figure 20. Launching the EVM GUI
8. If the EVM hardware is not plugged in, the status bar will indicate the hardware not connected.
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
15
EVM Software Overview
4
www.ti.com
EVM Software Overview
This section discusses how to use the EVM software.
4.1
Home Page
The home page is shown in Figure 21. The home page includes the EVM 3D model, features, and the
EVM block diagram.
Figure 21. Home Page
16
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Software Overview
www.ti.com
4.2
Collateral Page
The collateral page is shown in Figure 22. The page includes links to the device data sheet, EVM user's
guide, and other relevant technical documents.
Figure 22. Collateral Page
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
17
EVM Software Overview
4.3
www.ti.com
Data Capture
The data capture page is shown in Figure 23. The dual y-axis has units in degree Celsius. The left y-axis
is for the TMP6 and the right y-axis is for the TMP116. The x-axis is the sample number. The cursor
number is the current sample number the cursor is on.
Figure 23. Data Capture
4.4
4.4.1
Chart Settings
Acquisition Rate
The chart data sampling rate is fixed to 1 Hz.
4.4.2
Chart Refresh
The chart can be cleared by clicking on the Clear Chart button.
4.4.3
Save Data
Data acquired can be exported to a CSV file.
18
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Documentation
www.ti.com
5
EVM Documentation
This section contains the schematic diagram, layout, and complete bill of materials (BOM) for the EVM.
5.1
EVM Schematic
Figure 24 shows the schematic for the TMP6EVM board.
Figure 24. EVM Schematic
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
19
EVM Documentation
5.2
www.ti.com
EVM PCB Layout
Figure 25 through Figure 30 show the layout for the TMP6EVM board.
Figure 25. Top Layers
20
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Documentation
www.ti.com
Figure 26. Top Signal Layer
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
21
EVM Documentation
www.ti.com
Figure 27. Ground Layer
22
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Documentation
www.ti.com
Figure 28. Power Layer
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
23
EVM Documentation
www.ti.com
Figure 29. Bottom Signal Layer
24
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Documentation
www.ti.com
Figure 30. Bottom Layers
space
space
space
space
space
space
space
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
25
EVM Documentation
5.3
www.ti.com
EVM Bill of Materials
Table 3 lists the bill of materials for the EVM.
Table 3. EVM Bill of Material
Designator
Quantity
BT1
1
C1
1
C2
Description
PackageReference
PartNumber
Manufacturer
Battery Holder for
CR2032, SMT
Battery Holder for
CR2032, SMT
BK-912
Memory Protection
Devices
2.2uF
CAP, CERM, 2.2 uF, 10
V, +/- 10%, X5R, 0603
0603
C0603C225K8PACTU
Kemet
1
10uF
CAP, CERM, 10 uF, 10
V, +/- 20%, X5R, 0603
0603
C1608X5R1A106M080A
C
TDK
C3, C5, C8, C13, C14,
C15, C16
7
0.1uF
CAP, CERM, 0.1 uF, 16
V, +/- 5%, X7R, 0402
0402
GRM155R71C104JA88D MuRata
C4
1
0.01uF
CAP, CERM, 0.01 uF, 16 0402
V, +/- 10%, X7R, 0402
GRM155R71C103KA01D MuRata
C6, C7
2
0.1uF
CAP, CERM, 0.1 uF, 16
V, +/- 5%, X7R, 0603
0603
0603YC104JAT2A
C9, C12
2
220pF
CAP, CERM, 220 pF, 50
V, +/- 5%, C0G/NP0,
0402
0402
GRM1555C1H221JA01D MuRata
C10
1
0.47uF
CAP, CERM, 0.47 uF, 10 0603
V, +/- 10%, X7R, 0603
C0603C474K8RACTU
C11, C17
2
0.1uF
CAP, CERM, 0.1 uF, 10
V, +/- 10%, X5R, 0402
0402
GRM155R61A104KA01D MuRata
C18
1
2200pF
CAP, CERM, 2200 pF,
50 V, +/- 10%, X7R,
0603
0603
C0603X222K5RACTU
Kemet
D1
1
Green
LED, Green, SMD
LED_0603
LTST-C191TGKT
Lite-On
D2
1
5.6V
Diode, Zener, 5.6 V, 500
mW, SOD-123
SOD-123
MMSZ5232B-7-F
Diodes Inc.
D3
1
Orange
LED, Orange, SMD
LED_0603
LTST-C191KFKT
Lite-On
DS1
1
LCD Display Dot Pixels
128x128
LCD Display Dot Pixels
128x128
LS013B7DH03
Sharp Microelectronics
H1, H2, H3, H4
4
Bumpon, Cylindrical,
0.312 X 0.200, Black
Black Bumpon
SJ61A1
3M
J1
1
Receptacle, USB 2.0,
Micro B, 5 Position, R/A,
SMT
Receptacle, USB 2.0,
Micro B, 5 Pos, 0.65mm
Pitch, R/A, SMT
1051640001
Molex
J7
1
Connector, FPC 10 Pos.
9.1x2.0x5.6 mm
Connector PFC,
9.1x2.0x5.6mm
FH12-10S-0.5SH(55)
Hirose Electric Co. Ltd.
J8
1
Header, 2.54mm, 3x1,
Gold, SMT
Header, 2.54mm, 3x1,
SMT
M20-8770342
Harwin
26
Value
TMP6EVM User's Guide
AVX
Kemet
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Documentation
www.ti.com
Table 3. EVM Bill of Material (continued)
Designator
Quantity
Value
Description
PackageReference
PartNumber
Manufacturer
L1
1
10uH
Inductor, Shielded,
Ferrite, 10 uH, 0.4 A,
1.38 ohm, SMD
2.0x0.95x1.6mm
VLS201610ET-100M
TDK
Q1
1
-20V
MOSFET, P-CH, -20 V,
-3.7 A, SOT-23
SOT-23
SI2323DS
Vishay-Siliconix
R1, R2
2
33
RES, 33, 5%, 0.063 W,
0402
0402
CRCW040233R0JNED
Vishay-Dale
R3, R11, R17, R18
4
4.7k
RES, 4.7 k, 5%, 0.063 W, 0402
0402
CRCW04024K70JNED
Vishay-Dale
R4, R12, R13, R14, R15,
R16, R21, R22, R24,
R25
10
0
RES, 0, 5%, 0.063 W,
0402
0402
CRCW04020000Z0ED
Vishay-Dale
R5
1
110
RES, 110, 5%, 0.063 W,
0402
0402
CRCW0402110RJNED
Vishay-Dale
R6
1
1.5k
RES, 1.5 k, 5%, 0.063 W, 0402
0402
CRCW04021K50JNED
Vishay-Dale
R8
1
1.0Meg
RES, 1.0 M, 5%, 0.063
W, 0402
0402
CRCW04021M00JNED
Vishay-Dale
R9, R10
2
10.0k
RES, 10.0 k, 1%, 0.063
W, 0402
0402
CRCW040210K0FKED
Vishay-Dale
R19, R20
2
2.00Meg
RES, 2.00 M, 1%, 0.063
W, 0402
0402
CRCW04022M00FKED
Vishay-Dale
R23
1
33k
RES, 33 k, 5%, 0.063 W,
0402
0402
CRCW040233K0JNED
Vishay-Dale
RT2
1
Thermistor, DEC0002A
(X1SON-2)
DEC0002A
TMP6131DECR
Texas Instruments
RT6
1
Thermistor NTC, 10.0k
ohm, 1%, 0402
0402
NCP15XH103F03RC
MuRata
S1
1
Switch, Slide, SPDT,
0.2A, GULL, 12V, SMD
SMD, 3-Leads, Body
8.5x3.5mm, Pitch 2.5mm
CL-SB-12B-01T
Copal Electronics
SW0, SW1, SW2, SW3
4
Switch, SPST-NO, OffMom, 0.05A, 12VDC,
SMD
3.9x2.9mm
PTS820 J20M SMTR
LFS
C&K Components
TP1, TP2, TP3, TP4
4
Natural PC Test Point
Brass, SMT
Natural PC Test Point
Brass, SMT
S2761-46R
Harwin
U1
1
Micropower 150-mA Low- DBV0005A
Noise Ultra-Low-Dropout
Regulator in SOT-23 and
DSBGA Packages,
DBV0005A (SOT-23-5)
10k
SBOU202 – October 2018
Submit Documentation Feedback
LP2985AIM5X-3.0/NOPB Texas Instruments
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
27
EVM Documentation
www.ti.com
Table 3. EVM Bill of Material (continued)
Designator
Quantity
Description
PackageReference
PartNumber
Manufacturer
U2
1
ESD-Protection Array for
High-Speed Data
Interfaces, 4 Channels,
-40 to +85 degC, 6-pin
SON (DRY), Green
(RoHS & no Sb/Br)
DRY0006A
TPD4E004DRYR
Texas Instruments
U3
1
25 MHz Mixed Signal
Microcontroller with 128
KB Flash, 8192 B SRAM
and 47 GPIOs, -40 to 85
degC, 64-pin QFN
(RGC), Green (RoHS &
no Sb/Br)
RGC0064B
MSP430F5528IRGCR
Texas Instruments
U4
1
High-Accuracy, LowDRV0006A
Power, Digital
Temperature Sensor with
SMBus and Two-Wire
Serial Interface,
DRV0006A (WSON-6)
TMP116AIDRVR
Texas Instruments
Y1
1
Resonator, 4 MHz, 39pF
SMD
4.5x1.2x2 mm
CSTCR4M00G15L99-R0
MuRata
FID1, FID2, FID3
0
Fiducial mark. There is
nothing to buy or mount.
N/A
N/A
N/A
J2, J3, J5
0
Header, 2.54mm, 4x2,
Gold, TH
Header, 2.54mm, 4x2,
TH
TSW-104-08-L-D
Samtec
J4, J6
0
Header, 100mil, 5x2,
Gold, TH
5x2 Header
TSW-105-07-G-D
Samtec
R7
0
RES, 0, 5%, 0.063 W,
0402
0402
CRCW04020000Z0ED
Vishay-Dale
RT1, RT5
0
Thermistor, LPG0002A
(TO-92-2)
LPG0002A
PTC1131LPG
Texas Instruments
RT3, RT7
0
Thermistor, SOD-523
SOD-523
PTC1131SOD523
Texas Instruments
RT4, RT8
0
Thermistor, 0201
0201
PTC11310201
Texas Instruments
C1
1
2.2uF
CAP, CERM, 2.2 uF, 10
V, +/- 10%, X5R, 0603
0603
C0603C225K8PACTU
Kemet
C2
1
10uF
CAP, CERM, 10 uF, 10
V, +/- 20%, X5R, 0603
0603
C1608X5R1A106M080A
C
TDK
C3, C5, C8, C13, C14,
C15, C16
7
0.1uF
CAP, CERM, 0.1 uF, 16
V, +/- 5%, X7R, 0402
0402
GRM155R71C104JA88D MuRata
C4
1
0.01uF
CAP, CERM, 0.01 uF, 16 0402
V, +/- 10%, X7R, 0402
GRM155R71C103KA01D MuRata
28
Value
0
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Documentation
www.ti.com
Table 3. EVM Bill of Material (continued)
Designator
Quantity
Value
Description
PackageReference
PartNumber
Manufacturer
C6, C7
2
0.1uF
CAP, CERM, 0.1 uF, 16
V, +/- 5%, X7R, 0603
0603
0603YC104JAT2A
AVX
C9, C12
2
220pF
CAP, CERM, 220 pF, 50
V, +/- 5%, C0G/NP0,
0402
0402
GRM1555C1H221JA01D MuRata
C10
1
0.47uF
CAP, CERM, 0.47 uF, 10 0603
V, +/- 10%, X7R, 0603
C0603C474K8RACTU
C11, C17
2
0.1uF
CAP, CERM, 0.1 uF, 10
V, +/- 10%, X5R, 0402
0402
GRM155R61A104KA01D MuRata
C18
1
2200pF
CAP, CERM, 2200 pF,
50 V, +/- 10%, X7R,
0603
0603
C0603X222K5RACTU
Kemet
D1
1
Green
LED, Green, SMD
LED_0603
LTST-C191TGKT
Lite-On
D2
1
5.6V
Diode, Zener, 5.6 V, 500
mW, SOD-123
SOD-123
MMSZ5232B-7-F
Diodes Inc.
D3
1
Orange
LED, Orange, SMD
LED_0603
LTST-C191KFKT
Lite-On
DS1
1
LCD Display Dot Pixels
128x128
LCD Display Dot Pixels
128x128
LS013B7DH03
Sharp Microelectronics
H1, H2, H3, H4
4
Bumpon, Cylindrical,
0.312 X 0.200, Black
Black Bumpon
SJ61A1
3M
J1
1
Receptacle, USB 2.0,
Micro B, 5 Position, R/A,
SMT
Receptacle, USB 2.0,
Micro B, 5 Pos, 0.65mm
Pitch, R/A, SMT
1051640001
Molex
J7
1
Connector, FPC 10 Pos.
9.1x2.0x5.6 mm
Connector PFC,
9.1x2.0x5.6mm
FH12-10S-0.5SH(55)
Hirose Electric Co. Ltd.
J8
1
Header, 2.54mm, 3x1,
Gold, SMT
Header, 2.54mm, 3x1,
SMT
M20-8770342
Harwin
L1
1
10uH
Inductor, Shielded,
Ferrite, 10 uH, 0.4 A,
1.38 ohm, SMD
2.0x0.95x1.6mm
VLS201610ET-100M
TDK
Q1
1
-20V
MOSFET, P-CH, -20 V,
-3.7 A, SOT-23
SOT-23
SI2323DS
Vishay-Siliconix
R1, R2
2
33
RES, 33, 5%, 0.063 W,
0402
0402
CRCW040233R0JNED
Vishay-Dale
R3, R11, R17, R18
4
4.7k
RES, 4.7 k, 5%, 0.063 W, 0402
0402
CRCW04024K70JNED
Vishay-Dale
R4, R12, R13, R14, R15,
R16, R21, R22, R24,
R25
10
0
RES, 0, 5%, 0.063 W,
0402
0402
CRCW04020000Z0ED
Vishay-Dale
R5
1
110
RES, 110, 5%, 0.063 W,
0402
0402
CRCW0402110RJNED
Vishay-Dale
SBOU202 – October 2018
Submit Documentation Feedback
Kemet
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
29
EVM Documentation
www.ti.com
Table 3. EVM Bill of Material (continued)
Designator
Quantity
Value
Description
PartNumber
Manufacturer
R6
1
1.5k
RES, 1.5 k, 5%, 0.063 W, 0402
0402
CRCW04021K50JNED
Vishay-Dale
R8
1
1.0Meg
RES, 1.0 M, 5%, 0.063
W, 0402
0402
CRCW04021M00JNED
Vishay-Dale
R9, R10
2
10.0k
RES, 10.0 k, 1%, 0.063
W, 0402
0402
CRCW040210K0FKED
Vishay-Dale
R19, R20
2
2.00Meg
RES, 2.00 M, 1%, 0.063
W, 0402
0402
CRCW04022M00FKED
Vishay-Dale
R23
1
33k
RES, 33 k, 5%, 0.063 W,
0402
0402
CRCW040233K0JNED
Vishay-Dale
RT2
1
Thermistor, DPY0002A
(X1SON-2)
DPY0002A
PTC1131DPY
Texas Instruments
RT6
1
Thermistor NTC, 10.0k
ohm, 1%, 0402
0402
NCP15XH103F03RC
MuRata
S1
1
Switch, Slide, SPDT,
0.2A, GULL, 12V, SMD
SMD, 3-Leads, Body
8.5x3.5mm, Pitch 2.5mm
CL-SB-12B-01T
Copal Electronics
SW0, SW1, SW2, SW3
4
Switch, SPST-NO, OffMom, 0.05A, 12VDC,
SMD
3.9x2.9mm
PTS820 J20M SMTR
LFS
C&K Components
TP1, TP2, TP3, TP4
4
Natural PC Test Point
Brass, SMT
Natural PC Test Point
Brass, SMT
S2761-46R
Harwin
U1
1
Micropower 150-mA Low- DBV0005A
Noise Ultra-Low-Dropout
Regulator in SOT-23 and
DSBGA Packages,
DBV0005A (SOT-23-5)
LP2985AIM5X-3.0/NOPB Texas Instruments
U2
1
ESD-Protection Array for
High-Speed Data
Interfaces, 4 Channels,
-40 to +85 degC, 6-pin
SON (DRY), Green
(RoHS & no Sb/Br)
DRY0006A
TPD4E004DRYR
Texas Instruments
U3
1
25 MHz Mixed Signal
Microcontroller with 128
KB Flash, 8192 B SRAM
and 47 GPIOs, -40 to 85
degC, 64-pin QFN
(RGC), Green (RoHS &
no Sb/Br)
RGC0064B
MSP430F5528IRGCR
Texas Instruments
30
10k
PackageReference
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
EVM Documentation
www.ti.com
Table 3. EVM Bill of Material (continued)
Designator
Quantity
PartNumber
Manufacturer
U4
1
Value
High-Accuracy, LowDRV0006A
Power, Digital
Temperature Sensor with
SMBus and Two-Wire
Serial Interface,
DRV0006A (WSON-6)
TMP116AIDRVR
Texas Instruments
Y1
1
Resonator, 4 MHz, 39pF
SMD
4.5x1.2x2 mm
CSTCR4M00G15L99-R0
MuRata
FID1, FID2, FID3
0
Fiducial mark. There is
nothing to buy or mount.
N/A
N/A
N/A
J2, J3, J5
0
Header, 2.54mm, 4x2,
Gold, TH
Header, 2.54mm, 4x2,
TH
TSW-104-08-L-D
Samtec
J4, J6
0
Header, 100mil, 5x2,
Gold, TH
5x2 Header
TSW-105-07-G-D
Samtec
R7
0
RES, 0, 5%, 0.063 W,
0402
0402
CRCW04020000Z0ED
Vishay-Dale
RT1, RT5
0
Thermistor, LPG0002A
(TO-92-2)
LPG0002A
PTC1131LPG
Texas Instruments
RT4, RT8
0
Thermistor, 0201
0201
PTC11310201
Texas Instruments
0
Description
PackageReference
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
31
32
TMP6EVM User's Guide
SBOU202 – October 2018
Submit Documentation Feedback
EVM Documentation
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
SBOU202 – October 2018
Submit Documentation Feedback
TMP6EVM User's Guide
Copyright © 2018, Texas Instruments Incorporated
33
STANDARD TERMS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or
documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance
with the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License
Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused by
neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have
been altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specifications
or instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality control
techniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM.
User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10)
business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected.
2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or credit
User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty
period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or
replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be
warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software
associated with the kit to determine whether to incorporate such items in a finished product and software developers to write
software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or
otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition
that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.
Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must
operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 or RSS-247
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required to follow the
instructions set forth by Radio Law of Japan, which includes, but is not limited to, the instructions below with respect to EVMs
(which for the avoidance of doubt are stated strictly for convenience and should be verified by User):
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/
/www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
3.4 European Union
3.4.1
For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive):
This is a class A product intended for use in environments other than domestic environments that are connected to a
low-voltage power-supply network that supplies buildings used for domestic purposes. In a domestic environment this
product may cause radio interference in which case the user may be required to take adequate measures.
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY MATERIALS PROVIDED WITH THE EVM (INCLUDING, BUT NOT
LIMITED TO, REFERENCE DESIGNS AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL
FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT
NOT LIMITED TO ANY EPIDEMIC FAILURE WARRANTY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE
SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS SHALL BE
CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR
INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE
EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR
IMPROVEMENT, REGARDLESS OF WHEN MADE, CONCEIVED OR ACQUIRED.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS. THIS OBLIGATION SHALL APPLY
WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL
THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS OR THE USE OF THE EVMS , REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR
REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING,
OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF
USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI
MORE THAN TWELVE (12) MONTHS AFTER THE EVENT THAT GAVE RISE TO THE CAUSE OF ACTION HAS
OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY USE OF AN EVM PROVIDED
HEREUNDER, INCLUDING FROM ANY WARRANTY, INDEMITY OR OTHER OBLIGATION ARISING OUT OF OR IN
CONNECTION WITH THESE TERMS, , EXCEED THE TOTAL AMOUNT PAID TO TI BY USER FOR THE PARTICULAR
EVM(S) AT ISSUE DURING THE PRIOR TWELVE (12) MONTHS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE
CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
