TMS320VC5416GGU120

TMS320VC5416 Fixed-Point Digital Signal Processor Data Manual PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Literature Number: SPRS095P March 1999 – Revised October 2008 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. This data sheet revision history highlights the technical changes made to the SPRS095O device-specific data sheet to make it an SPRS095P revision. Scope: This document has been reviewed for technical accuracy; the technical content is up-to-date as of the specified release date with the following corrections. ADDITIONS/CHANGES/DELETIONS Table 2-2, Signal Descriptions: • Updated DESCRIPTION of TRST • Added footnote about TRST 2 Revision History Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Contents Revision History ........................................................................................................................... 2 1 TMS320VC5416 Features....................................................................................................... 9 2 Introduction ....................................................................................................................... 10 2.1 2.2 3 10 10 10 12 13 Functional Overview ........................................................................................................... 17 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 4 Description .................................................................................................................. Pin Assignments............................................................................................................ 2.2.1 Terminal Assignments for the GGU Package ............................................................... 2.2.2 Pin Assignments for the PGE Package ...................................................................... 2.2.3 Signal Descriptions .............................................................................................. Memory ...................................................................................................................... 3.1.1 Data Memory ..................................................................................................... 3.1.2 Program Memory ................................................................................................ 3.1.3 Extended Program Memory ................................................................................... On-Chip ROM With Bootloader........................................................................................... On-Chip RAM ............................................................................................................... On-Chip Memory Security ................................................................................................. Memory Map ................................................................................................................ 3.5.1 Relocatable Interrupt Vector Table ............................................................................ On-Chip Peripherals ....................................................................................................... 3.6.1 Software-Programmable Wait-State Generator ............................................................. 3.6.2 Programmable Bank-Switching ................................................................................ 3.6.3 Bus Holders ...................................................................................................... Parallel I/O Ports ........................................................................................................... 3.7.1 Enhanced 8-/16-Bit Host-Port Interface (HPI8/16) .......................................................... 3.7.2 HPI Nonmultiplexed Mode...................................................................................... Multichannel Buffered Serial Ports (McBSPs) .......................................................................... Hardware Timer ............................................................................................................ Clock Generator ............................................................................................................ Enhanced External Parallel Interface (XIO2) ........................................................................... DMA Controller ............................................................................................................. 3.12.1 Features .......................................................................................................... 3.12.2 DMA External Access ........................................................................................... 3.12.3 DMA Memory Maps ............................................................................................. 3.12.4 DMA Priority Level............................................................................................... 3.12.5 DMA Source/Destination Address Modification ............................................................. 3.12.6 DMA in Autoinitialization Mode ................................................................................ 3.12.7 DMA Transfer Counting......................................................................................... 3.12.8 DMA Transfer in Doubleword Mode .......................................................................... 3.12.9 DMA Channel Index Registers................................................................................. 3.12.10 DMA Interrupts .................................................................................................. 3.12.11 DMA Controller Synchronization Events ..................................................................... General-Purpose I/O Pins ................................................................................................. 3.13.1 McBSP Pins as General-Purpose I/O......................................................................... 3.13.2 HPI Data Pins as General-Purpose I/O ...................................................................... Device ID Register ......................................................................................................... Memory-Mapped Registers ............................................................................................... McBSP Control Registers and Subaddresses .......................................................................... DMA Subbank Addressed Registers .................................................................................... Interrupts .................................................................................................................... 17 17 18 18 18 19 19 20 21 23 23 25 26 26 27 28 30 32 32 34 37 37 37 39 40 40 41 41 41 42 42 42 43 43 44 44 45 47 48 50 Support ............................................................................................................................. 51 Contents 3 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 4.1 4.2 5 www.ti.com Documentation Support ................................................................................................... 51 Device and Development-Support Tool Nomenclature................................................................ 52 Electrical Specifications ...................................................................................................... 53 Absolute Maximum Ratings ............................................................................................... Recommended Operating Conditions ................................................................................... Electrical Characteristics ................................................................................................. 5.3.1 Test Loading ..................................................................................................... 5.3.2 Timing Parameter Symbology ............................................................................................ 5.3.3 Internal Oscillator With External Crystal................................................................................. 5.4 Clock Options ............................................................................................................... 5.4.1 Divide-By-Two and Divide-By-Four Clock Options .......................................................... 5.4.2 Multiply-By-N Clock Option (PLL Enabled)................................................................... 5.5 Memory and Parallel I/O Interface Timing .............................................................................. 5.5.1 Memory Read .................................................................................................... 5.5.2 Memory Write .................................................................................................... 5.5.3 I/O Read .......................................................................................................... 5.5.4 I/O Write .......................................................................................................... 5.5.5 Ready Timing for Externally Generated Wait States .................................................................. 5.5.6 HOLD and HOLDA Timings ............................................................................................... 5.5.7 Reset, BIO, Interrupt, and MP/MC Timings ............................................................................. 5.5.8 Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Timings .......................................... 5.5.9 External Flag (XF) and TOUT Timings .................................................................................. 5.5.10 Multichannel Buffered Serial Port (McBSP) Timing................................................................... 5.5.10.1 McBSP Transmit and Receive Timings .................................................................... 5.5.10.2 McBSP General-Purpose I/O Timing ....................................................................... 5.5.10.3 McBSP as SPI Master or Slave Timing .................................................................... 5.5.11 Host-Port Interface Timing ............................................................................................... 5.5.11.1 HPI8 Mode ..................................................................................................... 5.5.11.2 HPI16 Mode.................................................................................................... 5.1 5.2 5.3 6 Mechanical Data ................................................................................................................. 92 6.1 4 53 53 54 54 55 56 57 57 59 60 60 63 64 65 66 71 73 75 76 77 77 80 81 85 85 89 Package Thermal Resistance Characteristics .......................................................................... 92 Contents Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 List of Figures 2-1 144-Ball GGU MicroStar BGA™ (Bottom View) ............................................................................. 10 2-2 144-Pin PGE Low-Profile Quad Flatpack (Top View) ....................................................................... 12 3-1 TMS320VC5416 Functional Block Diagram .................................................................................. 17 3-2 Program and Data Memory Map ................................................................................................ 20 3-3 Extended Program Memory Map 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-14 3-15 3-16 3-17 3-18 3-19 3-20 3-21 3-22 3-23 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-14 ............................................................................................... Process Mode Status Register .................................................................................................. Software Wait-State Register (SWWSR) [Memory-Mapped Register (MMR) Address 0028h] ......................... Software Wait-State Register (SWWSR) [Memory-Mapped Register (MMR) Address 0028h] ......................... Bank-Switching Control Register BSCR)[MMR Address 0029h] ........................................................... Host-Port Interface — Nonmulltiplexed Mode ................................................................................. HPI Memory Map ................................................................................................................. Multichannel Control Register (MCR1) ......................................................................................... Multichannel Control Register (MCR2) ......................................................................................... Pin Control Register (PCR) ...................................................................................................... Nonconsecutive Memory Read and I/O Read Bus Sequence ............................................................. Consecutive Memory Read Bus Sequence (n = 3 reads) .................................................................. Memory Write and I/O Write Bus Sequence ................................................................................. DMA Transfer Mode Control Register (DMMCRn) ........................................................................... On-Chip DMA Memory Map for Program Space (DLAXS = 0 and SLAXS = 0)......................................... On-Chip DMA Memory Map for Data and IO Space (DLAXS = 0 and SLAXS = 0) .................................... DMPREC Register ................................................................................................................ General-Purpose I/O Control Register (GPIOCR) [MMR Address 003Ch] ................................................ General-Purpose I/O Status Register (GPIOSR) [MMR Address 003Dh] ................................................. Device ID Register (CSIDR) [MMR Address 003Eh] ......................................................................... IFR and IMR Registers ........................................................................................................... Tester Pin Electronics ............................................................................................................ Internal Divide-By-Two Clock Option With External Crystal ............................................................... External Divide-By-Two Clock Timing......................................................................................... Multiply-By-One Clock Timing .................................................................................................. Nonconsecutive Mode Memory Reads ....................................................................................... Consecutive Mode Memory Reads ............................................................................................ Memory Write (MSTRB = 0) .................................................................................................... Parallel I/O Port Read (IOSTRB = 0) ......................................................................................... Parallel I/O Port Write (IOSTRB = 0) .......................................................................................... Memory Read With Externally Generated Wait States ..................................................................... Memory Write With Externally Generated Wait States ..................................................................... I/O Read With Externally Generated Wait States ........................................................................... I/O Write With Externally Generated Wait States ........................................................................... HOLD and HOLDA Timings (HM = 1)......................................................................................... List of Figures 21 22 23 24 25 28 29 31 31 31 34 35 36 37 39 40 41 44 44 44 50 54 56 58 59 61 62 63 64 65 67 68 69 70 72 5 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 5-15 Reset and BIO Timings ......................................................................................................... 73 5-16 Interrupt Timing .................................................................................................................. 74 5-17 ................................................................................................................... Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Timings................................................ External Flag (XF) Timing ...................................................................................................... TOUT Timing ..................................................................................................................... McBSP Receive Timings ....................................................................................................... McBSP Transmit Timings ....................................................................................................... McBSP General-Purpose I/O Timings ........................................................................................ McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0 .................................................... McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0 .................................................... McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1 .................................................... McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1 .................................................... Using HDS to Control Accesses (HCS Always Low)........................................................................ Using HCS to Control Accesses ............................................................................................... HINT Timing ...................................................................................................................... GPIOx Timings ................................................................................................................... Nonmultiplexed Read Timings ................................................................................................. Nonmultiplexed Write Timings ................................................................................................. HRDY Relative to CLKOUT .................................................................................................... 5-18 5-19 5-20 5-21 5-22 5-23 5-24 5-25 5-26 5-27 5-28 5-29 5-30 5-31 5-32 5-33 5-34 6 MP/MC Timing List of Figures 74 75 76 76 78 79 80 81 82 83 84 87 88 88 88 90 91 91 Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 List of Tables 2-1 2-2 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-14 3-15 3-16 3-17 3-18 3-19 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-14 5-15 5-16 5-17 5-18 ......................................... Signal Descriptions ............................................................................................................... Standard On-Chip ROM Layout ............................................................................................... Processor Mode Status (PMST) Register Bit Fields ........................................................................ Software Wait-State Register (SWWSR) Bit Fields ......................................................................... Software Wait-State Control Register (SWCR) Bit Fields .................................................................. Bank-Switching Control Register (BSCR) Fields.............................................................................. Bus Holder Control Bits .......................................................................................................... Sample Rate Input Clock Selection ........................................................................................... Clock Mode Settings at Reset ................................................................................................. DMD Section of the DMMCRn Register ...................................................................................... DMA Reload Register Selection ............................................................................................... DMA Interrupts ................................................................................................................... DMA Synchronization Events .................................................................................................. DMA Channel Interrupt Selection .............................................................................................. Device ID Register (CSIDR) Bits ................................................................................................ CPU Memory-Mapped Registers................................................................................................ Peripheral Memory-Mapped Registers for Each DSP Subsystem ........................................................ McBSP Control Registers and Subaddresses................................................................................. DMA Subbank Addressed Registers ........................................................................................... Interrupt Locations and Priorities................................................................................................ Input Clock Frequency Characteristics ......................................................................................... Clock Mode Pin Settings for the Divide-By-2 and By Divide-By-4 Clock Options ....................................... Divide-By-2 and Divide-By-4 Clock Options Timing Requirements ....................................................... Divide-By-2 and Divide-By-4 Clock Options Switching Characteristics................................................... Multiply-By-N Clock Option Timing Requirements .......................................................................... Multiply-By-N Clock Option Switching Characteristics ...................................................................... Memory Read Timing Requirements .......................................................................................... Memory Read Switching Characteristics ..................................................................................... Memory Write Switching Characteristics ..................................................................................... I/O Read Timing Requirements ................................................................................................ I/O Read Switching Characteristics ........................................................................................... I/O Write Switching Characteristics............................................................................................ Ready Timing Requirements for Externally Generated Wait States ...................................................... Ready Switching Characteristics for Externally Generated Wait States .................................................. HOLD and HOLDA Timing Requirements .................................................................................... HOLD and HOLDA Switching Characteristics ............................................................................... Reset, BIO, Interrupt, and MP/MC Timing Requirements .................................................................. Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Switching Characteristics ........................... Terminal Assignments for the TMS320VC5416GGU (144-Pin BGA Package) List of Tables 11 13 19 22 24 24 25 26 32 33 38 41 42 42 43 44 45 45 47 48 50 56 57 57 57 59 59 60 60 63 64 64 65 66 66 71 71 73 75 7 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 5-19 External Flag (XF) and TOUT Switching Characteristics ................................................................... 76 5-20 McBSP Transmit and Receive Timing Requirements....................................................................... 77 5-21 McBSP Transmit and Receive Switching Characteristics .................................................................. 78 5-22 McBSP General-Purpose I/O Timing Requirements ........................................................................ 80 5-23 5-24 5-25 5-26 5-27 5-28 5-29 5-30 5-31 5-32 5-33 5-34 5-35 6-1 8 ................................................................... McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 0) ................................. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 0) ............................. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 0) ................................. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 0) ............................. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 1) ................................. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 1) ............................. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 1) ................................. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 1) ............................. HPI8 Mode Timing Requirements ............................................................................................. HPI8 Mode Switching Characteristics .......................................................................................... HPI16 Mode Timing Requirements ............................................................................................ HPI16 Mode Switching Characteristics ....................................................................................... Thermal Resistance Characteristics ............................................................................................ McBSP General-Purpose I/O Switching Characteristics List of Tables 80 81 81 82 82 83 83 84 84 85 86 89 90 92 Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 1 • • • • • • • • • • • • • • • SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 TMS320VC5416 Features Advanced Multibus Architecture With Three Separate 16-Bit Data Memory Buses and One Program Memory Bus 40-Bit Arithmetic Logic Unit (ALU) Including a 40-Bit Barrel Shifter and Two Independent 40-Bit Accumulators 17- × 17-Bit Parallel Multiplier Coupled to a 40-Bit Dedicated Adder for Non-Pipelined Single-Cycle Multiply/Accumulate (MAC) Operation Compare, Select, and Store Unit (CSSU) for the Add/Compare Selection of the Viterbi Operator Exponent Encoder to Compute an Exponent Value of a 40-Bit Accumulator Value in a Single Cycle Two Address Generators With Eight Auxiliary Registers and Two Auxiliary Register Arithmetic Units (ARAUs) Data Bus With a Bus Holder Feature Extended Addressing Mode for 8M × 16-Bit Maximum Addressable External Program Space 128K × 16-Bit On-Chip RAM Composed of: – Eight Blocks of 8K × 16-Bit On-Chip Dual-Access Program/Data RAM – Eight Blocks of 8K × 16-Bit On-Chip Single-Access Program RAM 16K × 16-Bit On-Chip ROM Configured for Program Memory Enhanced External Parallel Interface (XIO2) Single-Instruction-Repeat and Block-Repeat Operations for Program Code Block-Memory-Move Instructions for Better Program and Data Management Instructions With a 32-Bit Long Word Operand Instructions With Two- or Three-Operand • • • • • • • • • • • • • • (1) Reads Arithmetic Instructions With Parallel Store and Parallel Load Conditional Store Instructions Fast Return From Interrupt On-Chip Peripherals – Software-Programmable Wait-State Generator and Programmable Bank-Switching – On-Chip Programmable Phase-Locked Loop (PLL) Clock Generator With External Clock Source – One 16-Bit Timer – Six-Channel Direct Memory Access (DMA) Controller – Three Multichannel Buffered Serial Ports (McBSPs) – 8/16-Bit Enhanced Parallel Host-Port Interface (HPI8/16) Power Consumption Control With IDLE1, IDLE2, and IDLE3 Instructions With Power-Down Modes CLKOUT Off Control to Disable CLKOUT On-Chip Scan-Based Emulation Logic, IEEE Std 1149.1 (JTAG) Boundary Scan Logic (1) 144-Pin Ball Grid Array (BGA)(GGU Suffix) 144-Pin Low-Profile Quad Flatpack (LQFP)(PGE Suffix) 6.25-ns Single-Cycle Fixed-Point Instruction Execution Time (160 MIPS) 8.33-ns Single-Cycle Fixed-Point Instruction Execution Time (120 MIPS) 3.3-V I/O Supply Voltage (160 and 120 MIPS) 1.6-V Core Supply Voltage (160 MIPS) 1.5-V Core Supply Voltage (120 MIPS) IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture TMS320C54x, TMS320 are trademarks of Texas Instruments. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1999–2008, Texas Instruments Incorporated TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 2 www.ti.com Introduction This section describes the main features of the TMS320VC5416, lists the pin assignments, and describes the function of each pin. This data manual also provides a detailed description section, electrical specifications, parameter measurement information, and mechanical data about the available packaging. NOTE This data manual is designed to be used in conjunction with the TMS320C54x™ DSP Functional Overview (literature number SPRU307). 2.1 Description The TMS320VC5416 fixed-point, digital signal processor (DSP) (hereafter referred to as the device unless otherwise specified) is based on an advanced modified Harvard architecture that has one program memory bus and three data memory buses. This processor provides an arithmetic logic unit (ALU) with a high degree of parallelism, application-specific hardware logic, on-chip memory, and additional on-chip peripherals. The basis of the operational flexibility and speed of this DSP is a highly specialized instruction set. Separate program and data spaces allow simultaneous access to program instructions and data, providing a high degree of parallelism. Two read operations and one write operation can be performed in a single cycle. Instructions with parallel store and application-specific instructions can fully utilize this architecture. In addition, data can be transferred between data and program spaces. Such parallelism supports a powerful set of arithmetic, logic, and bit-manipulation operations that can all be performed in a single machine cycle. The device also includes the control mechanisms to manage interrupts, repeated operations, and function calls. 2.2 Pin Assignments Figure 2-1 illustrates the ball locations for the 144-pin ball grid array (BGA) package and is used in conjunction with Table 2-1 to locate signal names and ball grid numbers. Figure 2-2 provides the pin assignments for the 144-pin low-profile quad flatpack (LQFP) package. 2.2.1 Terminal Assignments for the GGU Package 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H J K L M N Figure 2-1. 144-Ball GGU MicroStar BGA™ (Bottom View) 10 Introduction Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Table 2-1 lists each signal name and BGA ball number for the 144-pin TMS320VC5416GGU package. Table 2-2 lists each terminal name, terminal function, and operating modes for the TMS320VC5416. In Table 2-1, DVDD is the power supply for the I/O pins while CVDD is the power supply for the core CPU. Table 2-1. Terminal Assignments for the TMS320VC5416GGU (144-Pin BGA Package) SIGNAL QUADRANT 1 BGA BALL # SIGNAL QUADRANT 2 SIGNAL QUADRANT 3 BGA BALL # SIGNAL QUADRANT 4 BGA BALL # CVSS A1 BFSX1 A22 B1 BDX1 N13 CVSS N1 A19 A13 M13 BCLKR1 N2 A20 CVSS C2 DVDD A12 L12 HCNTL0 M3 CVSS DVDD C1 B11 DVSS L13 DVSS N3 DVDD A11 BGA BALL # A10 D4 CLKMD1 K10 BCLKR0 K4 D6 D10 HD7 D3 CLKMD2 K11 BCLKR2 L4 D7 C10 A11 D2 CLKMD3 K12 BFSR0 M4 D8 B10 A12 D1 HPI16 K13 BFSR2 N4 D9 A10 A13 E4 HD2 J10 BDR0 K5 D10 D9 A14 E3 TOUT J11 HCNTL1 L5 D11 C9 B9 A15 E2 EMU0 J12 BDR2 M5 D12 CVDD E1 EMU1/OFF J13 BCLKX0 N5 HD4 A9 HAS F4 TDO H10 BCLKX2 K6 D13 D8 DVSS F3 TDI H11 CVSS L6 D14 C8 CVSS F2 TRST H12 HINT M6 D15 B8 CVDD F1 TCK H13 CVDD N6 HD5 A8 HCS G2 TMS G12 BFSX0 M7 CVDD B7 HR/W G1 CVSS G13 BFSX2 N7 CVSS A7 READY G3 CVDD G11 HRDY L7 HDS1 C7 PS G4 HPIENA G10 DVDD K7 DVSS D7 DS H1 DVSS F13 DVSS N8 HDS2 A6 IS H2 CLKOUT F12 HD0 M8 DVDD B6 R/W H3 HD3 F11 BDX0 L8 A0 C6 MSTRB H4 X1 F10 BDX2 K8 A1 D6 IOSTRB J1 X2/CLKIN E13 IACK N9 A2 A5 MSC J2 RS E12 HBIL M9 A3 B5 XF J3 D0 E11 NMI L9 HD6 C5 HOLDA J4 D1 E10 INT0 K9 A4 D5 IAQ K1 D2 D13 INT1 N10 A5 A4 HOLD K2 D3 D12 INT2 M10 A6 B4 BIO K3 D4 D11 INT3 L10 A7 C4 MP/MC L1 D5 C13 CVDD N11 A8 A3 DVDD L2 A16 C12 HD1 M11 A9 B3 CVSS L3 DVSS C11 CVSS L11 CVDD C3 BDR1 M1 A17 B13 BCLKX1 N12 A21 A2 BFSR1 M2 A18 B12 DVSS M12 DVSS B2 Submit Documentation Feedback Introduction 11 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 2.2.2 www.ti.com Pin Assignments for the PGE Package 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 DVSS A21 CV DD A9 A8 A7 A6 A5 A4 HD6 A3 A2 A1 A0 DV DD HDS2 DV SS HDS1 CVSS CVDD HD5 D15 D14 D13 HD4 D12 D11 D10 D9 D8 D7 D6 DV DD CV SS A20 A19 The TMS320VC5416PGE 144-pin low-profile quad flatpack (LQFP) pin assignments are shown in Figure 2-2. DVDD is the power supply for the I/O pins while CVDD is the power supply for the core CPU. VSS is the ground for both the I/O pins and the core CPU. 108 107 106 4 5 6 7 105 104 103 102 8 9 10 11 101 100 99 98 12 13 14 15 97 96 95 94 16 17 18 19 20 93 92 91 90 89 21 22 23 24 88 87 86 85 25 26 27 28 84 83 82 81 29 30 31 32 80 79 78 77 33 34 35 36 76 75 74 73 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 1 2 3 A18 A17 DVSS A16 D5 D4 D3 D2 D1 D0 RS X2/CLKIN X1 HD3 CLKOUT DVSS HPIENA CVDD CVSS TMS TCK TRST TDI TDO EMU1/OFF EMU0 TOUT HD2 HPI16 CLKMD3 CLKMD2 CLKMD1 DVSS DVDD BDX1 BFSX1 CV SS BCLKR1 HCNTL0 DVSS BCLKR0 BCLKR2 BFSR0 BFSR2 BDR0 HCNTL1 BDR2 BCLKX0 BCLKX2 CVSS HINT CVDD BFSX0 BFSX2 HRDY DVDD DVSS HD0 BDX0 BDX2 IACK HBIL NMI INT0 INT1 INT2 INT3 CV DD HD1 CVSS BCLKX1 DVSS CVSS A22 CVSS DVDD A10 HD7 A11 A12 A13 A14 A15 CVDD HAS DVSS CVSS CVDD HCS HR/W READY PS DS IS R/W MSTRB IOSTRB MSC XF HOLDA IAQ HOLD BIO MP/MC DVDD CVSS BDR1 BFSR1 Figure 2-2. 144-Pin PGE Low-Profile Quad Flatpack (Top View) 12 Introduction Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 2.2.3 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Signal Descriptions Table 2-2 lists each signal, function, and operating mode(s) grouped by function. Table 2-2. Signal Descriptions TERMINAL NAME I/O (1) DESCRIPTION DATA SIGNALS A22 (MSB), I/O/Z (2) (3) A21, A20, A19, A18, A17, A16, A15, A14, A13, A12, A11, A10, A9, A8, A7, A6, A5, A4, A3, A2, A1, A0 (LSB) D15 (MSB), D14, D13, D12, D11, D10, D9, D8, D7, D6, D5, D4, D3, D2, D1, D0 (LSB) Parallel address bus A22 [most significant bit (MSB)] through A0 [least significant bit (LSB)]. The sixteen LSB lines, A0 to A15, are multiplexed to address external memory (program, data) or I/O. The seven MSB lines, A16 to A22, address external program space memory. A22-A0 is placed in the high-impedance state in the hold mode. A22-A0 also goes into the high-impedance state when OFF is low.A17-A0 are inputs in HPI16 mode. These pins can be used to address internal memory via the host-port interface (HPI) when the HPI16 pin is high. These pins also have Schmitt trigger inputs.The address bus has a bus holder feature that eliminates passive components and the power dissipation associated with them. The bus holder keeps the address bus at the previous logic level when the bus goes into a high-impedance state. I/O/Z (2) (3) Parallel data bus D15 (MSB) through D0 (LSB). D15-D0 is multiplexed to transfer data between the core CPU and external data/program memory or I/O devices or HPI in HPI16 mode (when HPI16 pin is high). D15-D0 is placed in the high-impedance state when not outputting data or when RS or HOLD is asserted. D15-D0 also goes into the high-impedance state when OFF is low. These pins also have Schmitt trigger inputs.The data bus has a bus holder feature that eliminates passive components and the power dissipation associated with them. The bus holder keeps the data bus at the previous logic level when the bus goes into the high-impedance state. The bus holders on the data bus can be enabled/disabled under software control. INITIALIZATION, INTERRUPT AND RESET OPERATIONS IACK O/Z Interrupt acknowledge signal. IACK indicates receipt of an interrupt and that the program counter is fetching the interrupt vector location designated by A15-A0. IACK also goes into the high-impedance state when OFF is low. INT0 (2) INT1 (2) INT2 (2) INT3 (2) I External user interrupt inputs. INT0-INT3 are maskable and are prioritized by the interrupt mask register (IMR) and the interrupt mode bit. INT0 -INT3 can be polled and reset by way of the interrupt flag register (IFR). (2) I Nonmaskable interrupt. NMI is an external interrupt that cannot be masked by way of the INTM or the IMR. When NMI is activated, the processor traps to the appropriate vector location. I Reset. RS causes the digital signal processor (DSP) to terminate execution and forces the program counter to 0FF80h. When RS is brought to a high level, execution begins at location 0FF80h of program memory. RS affects various registers and status bits. I Microprocessor/microcomputer mode select. If active low at reset, microcomputer mode is selected, and the internal program ROM is mapped into the upper 16K words of program memory space. If the pin is driven high during reset, microprocessor mode is selected, and the on-chip ROM is removed from program space. This pin is only sampled at reset, and the MP/MC bit of the processor mode status (PMST) register can override the mode that is selected at reset. NMI RS (2) MP/MC MULTIPROCESSING SIGNALS BIO (2) XF I O/Z Branch control. A branch can be conditionally executed when BIO is active. If low, the processor executes the conditional instruction. The BIO condition is sampled during the decode phase of the pipeline for the XC instruction, and all other instructions sample BIO during the read phase of the pipeline. External flag output (latched software-programmable signal). XF is set high by the SSBX XF instruction, set low by RSBX XF instruction or by loading ST1. XF is used for signaling other processors in multiprocessor configurations or used as a general-purpose output pin. XF goes into the high-impedance state when OFF is low, and is set high at reset. MEMORY CONTROL SIGNALS DS PS IS O/Z Data, program, and I/O space select signals. DS, PS, and IS are always high unless driven low for communicating to a particular external space. Active period corresponds to valid address information. DS, PS, and IS are placed into the high-impedance state in the hold mode; these signals also go into the high-impedance state when OFF is low. MSTRB O/Z Memory strobe signal. MSTRB is always high unless low-level asserted to indicate an external bus access to data or program memory. MSTRB is placed in the high-impedance state in the hold mode; it also goes into the high-impedance state when OFF is low. (1) (2) (3) I = Input, O = Output, Z = High-impedance, S = Supply These pins have Schmitt trigger inputs. This pin has an internal bus holder controlled by way of the BSCR register. Submit Documentation Feedback Introduction 13 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Table 2-2. Signal Descriptions (continued) TERMINAL NAME I/O (1) READY I DESCRIPTION Data ready. READY indicates that an external device is prepared for a bus transaction to be completed. If the device is not ready (READY is low), the processor waits one cycle and checks READY again. Note that the processor performs ready detection if at least two software wait states are programmed. The READY signal is not sampled until the completion of the software wait states. R/W O/Z Read/write signal. R/W indicates transfer direction during communication to an external device. R/W is normally in the read mode (high), unless it is asserted low when the DSP performs a write operation. R/W is placed in the high-impedance state in the hold mode; and it also goes into the high-impedance state when OFF is low. IOSTRB O/Z I/O strobe signal. IOSTRB is always high unless low-level asserted to indicate an external bus access to an I/O device. IOSTRB is placed in the high-impedance state in the hold mode; it also goes into the high-impedance state when OFF is low. I Hold input. HOLD is asserted to request control of the address, data, and control lines. When acknowledged by the device, these lines go into the high-impedance state. HOLD O/Z Hold acknowledge. HOLDA indicates to the external circuitry that the processor is in a hold state and that the address, data, and control lines are in the high-impedance state, allowing them to be available to the external circuitry. HOLDA also goes into the high-impedance state when OFF is low.Figure 2-2 This pin is driven high during reset. MSC O/Z Microstate complete. MSC indicates completion of all software wait states. When two or more software wait states are enabled, the MSC pin goes active at the beginning of the first software wait state and goes inactive high at the beginning of the last software wait state. If connected to the READY input, MSC forces one external wait state after the last internal wait state is completed. MSC also goes into the high-impedance state when OFF is low. IAQ O/Z Instruction acquisition signal. IAQ is asserted (active low) when there is an instruction address on the address bus and goes into the high-impedance state when OFF is low. HOLDA TIMER SIGNALS CLKOUT O/Z Clock output signal. CLKOUT can represent the machine-cycle rate of the CPU divided by 1, 2, 3, or 4 as configured in the bank-switching control register (BSCR). Following reset, CLKOUT represents the machine-cycle rate divided by 4. CLKMD1 (2) CLKMD2 (2) CLKMD3 (2) I Clock mode select signals. CLKMD1-CLKMD3 allow the selection and configuration of different clock modes such as crystal, external clock, and PLL mode. The external CLKMD1-CLKMD3 pins are sampled to determine the desired clock generation mode while RS is low. Following reset, the clock generation mode can be reconfigured by writing to the internal clock mode register in software. X2/CLKIN (2) I Clock/oscillator input. If the internal oscillator is not being used, X2/CLKIN functions as the clock input. (This is revision-dependent, see Section 3.10 for additional information.) X1 O Output pin from the internal oscillator for the crystal. If the internal oscillator is not used, X1 should be left unconnected. X1 does not go into the high-impedance state when OFF is low. (This is revision-dependent, see Section 3.10 for additional information.) O/Z Timer output. TOUT signals a pulse when the on-chip timer counts down past zero. The pulse is one CLKOUT cycle wide. TOUT also goes into the high-impedance state when OFF is low. TOUT MULTICHANNEL BUFFERED SERIAL PORT 0 (McBSP #0), MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP #1), AND MULTICHANNEL BUFFERED SERIAL PORT 2 (McBSP #2) SIGNALS BCLKR0 (2) BCLKR1 (2) BCLKR2 (2) I/O/Z BDR0, BDR1, BDR2 I Receive clock input. BCLKR can be configured as an input or an output; it is configured as an input following reset. BCLKR serves as the serial shift clock for the buffered serial port receiver. Serial data receive input BFSR0, BFSR1, BFSR2 I/O/Z Frame synchronization pulse for receive input. BFSR can be configured as an input or an output; it is configured as an input following reset. The BFSR pulse initiates the receive data process over BDR. BCLKX0 (2) BCLKX1 (2) BCLKX2 (2) I/O/Z Transmit clock. BCLKX serves as the serial shift clock for the McBSP transmitter. BCLKX can be configured as an input or an output, and is configured as an input following reset. BCLKX enters the high-impedance state when OFF goes low. BDX0, BDX1, BDX2 O/Z Serial data transmit output. BDX is placed in the high-impedance state when not transmitting, when RS is asserted, or when OFF is low. BFSX0, BFSX1, BFSX2 I/O/Z Frame synchronization pulse for transmit input/output. The BFSX pulse initiates the data transmit process over BDX. BFSX can be configured as an input or an output, and is configured as an input following reset. BFSX goes into the high-impedance state when OFF is low. 14 Introduction Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Table 2-2. Signal Descriptions (continued) TERMINAL NAME I/O (1) DESCRIPTION HOST-PORT INTERFACE SIGNALS I/O/Z Parallel bidirectional data bus. The HPI data bus is used by a host device bus to exchange information with the HPI registers. These pins can also be used as general-purpose I/O pins. HD0-HD7 is placed in the high-impedance state when not outputting data or when OFF is low. The HPI data bus includes bus holders to reduce the static power dissipation caused by floating, unused pins. When the HPI data bus is not being driven by the device, the bus holders keep the pins at the previous logic level. The HPI data bus holders are disabled at reset and can be enabled/disabled via the HBH bit of the BSCR. These pins also have Schmitt trigger inputs. HCNTL0 (4) HCNTL1 (4) I Control inputs. HCNTL0 and HCNTL1 select a host access to one of the three HPI registers. The control inputs have internal pullups that are only enabled when HPIENA = 0. These pins are not used when HPI16 = 1. HBIL (4) I Byte identification. HBIL identifies the first or second byte of transfer. The HPIL input has an internal pullup resistor that is only enabled when HPIENA = 0. This pin is not used when HPI16 = 1. (2) (4) I Chip select. HCS is the select input for the HPI and must be driven low during accesses. The chip select input has an internal pullup resistor that is only enabled when HPIENA = 0. HDS1 (2) (4) HDS2 (2) (4) I Data strobe. HDS1 and HDS2 are driven by the host read and write strobes to control the transfer. The strobe inputs have internal pullup resistors that are only enabled when HPIENA = 0. (2) (4) I Address strobe. Host with multiplexed address and data pins requires HAS to latch the address in the HPIA register. HAS input has an internal pullup resistor that is only enabled when HPIENA = 0. I Read/write. HR/W controls the direction of the HPI transfer. HR/W has an internal pullup resistor that is only enabled when HPIENA = 0. HD0HD7 (2) (3) HCS HAS HR/W (4) HRDY O/Z Ready output. HRDY goes into the high-impedance state when OFF is low. The ready output informs the host when the HPI is ready for the next transfer. This pin is driven high during reset. HINT O/Z Interrupt output. This output is used to interrupt the host. When the DSP is in reset, HINT is driven high. HINT goes into the high-impedance state when OFF is low. This pin is not used when HPI16 = 1. HPIENA (5) HPI16 (5) I HPI module select. HPIENA must be tied to DVDD to have HPI selected. If HPIENA is left open or connected to ground, the HPI module is not selected, internal pullup for the HPI input pins are enabled, and the HPI data bus has holders set. HPIENA is provided with an internal pulldown resistor that is always active. HPIENA is sampled when RS goes high and is ignored until RS goes low again. This pin should never be changed while reset is high. I HPI16 mode selection. This pin must be tied to DVDD to enable HPI16 mode. The pin has an internal pulldown resistor which is always active. If HPI16 is left open or driven low, the HPI16 mode is disabled. SUPPLY PINS CVSS S Ground. Dedicated ground for the core CPU CVDD S +VDD. Dedicated power supply for the core CPU DVSS S Ground. Dedicated ground for I/O pins DVDD S +VDD. Dedicated power supply for I/O pins TCK (2) (4) I IEEE standard 1149.1 test clock. TCK is normally a free-running clock signal with a 50% duty cycle. The changes on test access port (TAP) of input signals TMS and TDI are clocked into the TAP controller, instruction register, or selected test data register on the rising edge of TCK. Changes at the TAP output signal (TDO) occur on the falling edge of TCK. TDI (4) I IEEE standard 1149.1 test data input. Pin with internal pullup device. TDI is clocked into the selected register (instruction or data) on a rising edge of TCK. TDO O/Z TEST PINS TMS (4) TRST (4) (5) (6) (5) (6) IEEE standard 1149.1 test data output. The contents of the selected register (instruction or data) are shifted out of TDO on the falling edge of TCK. TDO is in the high-impedance state except when the scanning of data is in progress. TDO also goes into the high-impedance state when OFF is low. I IEEE standard 1149.1 test mode select. Pin with internal pullup device. This serial control input is clocked into the TAP controller on the rising edge of TCK. I IEEE standard 1149.1 test reset. TRST, when high, gives the IEEE standard 1149.1 scan system control of the operations of the device. If TRST is driven low, the device operates in its functional mode, and the IEEE standard 1149.1 signals are ignored. Pin with internal pulldown device. This pin has an internal pullup resistor. This pin has an internal pulldown resistor. Although this pin includes an internal pulldown resistor, a 470-Ω external pulldown is required. If the TRST pin is connected to multiple DSPs, a buffer is recommended to ensure the VIL and VIH specifications are met. Submit Documentation Feedback Introduction 15 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Table 2-2. Signal Descriptions (continued) TERMINAL NAME EMU0 (7) EMU1/OFF (7) (7) 16 I/O (1) DESCRIPTION I/O/Z Emulator 0 pin. When TRST is driven low, EMU0 must be high for activation of the OFF condition. When TRST is driven high, EMU0 is used as an interrupt to or from the emulator system and is defined as input/output by way of the IEEE standard 1149.1 scan system. I/O/Z Emulator 1 pin/disable all outputs. When TRST is driven high, EMU1/OFF is used as an interrupt to or from the emulator system and is defined as input/output by way of IEEE standard 1149.1 scan system. When TRST is driven low, EMU1/OFF is configured as OFF. The EMU1/OFF signal, when active low, puts all output drivers into the high-impedance state. Note that OFF is used exclusively for testing and emulation purposes (not for multiprocessing applications). Therefore, for the OFF condition, the following apply: TRST = low, EMU0 = high EMU1/OFF = low This pin must be pulled up with a 4.7-kΩ resistor to ensure the device is operable in functional mode or emulation mode. Introduction Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 3 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Functional Overview The following functional overview is based on the block diagram in Figure 3-1. 54X cLEAD 64K RAM Single Access Program Pbus Dbus Ebus Cbus Pbus Ebus Pbus Ebus Cbus Pbus Dbus P, C, D, E Buses and Control Signals 64K RAM Dual Access Program/Data 16K Program ROM MBus GPIO TI BUS XIO RHEA Bridge RHEA Bus McBSP1 16HPI 16 HPI xDMA logic McBSP2 MBus RHEA bus Enhanced XIO McBSP3 RHEAbus TIMER APLL Clocks JTAG Figure 3-1. TMS320VC5416 Functional Block Diagram 3.1 Memory The device provides both on-chip ROM and RAM memories to aid in system performance and integration. 3.1.1 Data Memory The data memory space addresses up to 64K of 16-bit words. The device automatically accesses the on-chip RAM when addressing within its bounds. When an address is generated outside the RAM bounds, the device automatically generates an external access. The advantages of operating from on-chip memory are as follows: • Higher performance because no wait states are required • Higher performance because of better flow within the pipeline of the central arithmetic logic unit (CALU) • Lower cost than external memory • Lower power than external memory The advantage of operating from off-chip memory is the ability to access a larger address space. Submit Documentation Feedback Functional Overview 17 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 3.1.2 www.ti.com Program Memory Software can configure their memory cells to reside inside or outside of the program address map. When the cells are mapped into program space, the device automatically accesses them when their addresses are within bounds. When the program-address generation (PAGEN) logic generates an address outside its bounds, the device automatically generates an external access. The advantages of operating from on-chip memory are as follows: • Higher performance because no wait states are required • Lower cost than external memory • Lower power than external memory The advantage of operating from off-chip memory is the ability to access a larger address space. 3.1.3 Extended Program Memory The device uses a paged extended memory scheme in program space to allow access of up to 8192K of program memory. In order to implement this scheme, the device includes several features which are also present on C548/549/5410: • Twenty-three address lines, instead of sixteen • An extra memory-mapped register, the XPC • Six extra instructions for addressing extended program space Program memory in the device is organized into 128 pages that are each 64K in length. The value of the XPC register defines the page selection. This register is memory-mapped into data space to address 001Eh. At a hardware reset, the XPC is initialized to 0. 3.2 On-Chip ROM With Bootloader The device features a 16K-word × 16-bit on-chip maskable ROM that can only be mapped into program memory space. Customers can arrange to have the ROM of the device programmed with contents unique to any particular application. A bootloader is available in the standard on-chip ROM. This bootloader can be used to automatically transfer user code from an external source to anywhere in the program memory at power up. If MP/MC of the device is sampled low during a hardware reset, execution begins at location FF80h of the on-chip ROM. This location contains a branch instruction to the start of the bootloader program. The standard devices provide different ways to download the code to accommodate various system requirements: • Parallel from 8-bit or 16-bit-wide EPROM • Parallel from I/O space, 8-bit or 16-bit mode • Serial boot from serial ports, 8-bit or 16-bit mode • Host-port interface boot • Warm boot 18 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 The standard on-chip ROM layout is shown in Table 3-1. Table 3-1. Standard On-Chip ROM Layout ADDRESS RANGE DESCRIPTION C000h-D4FFh ROM tables for the GSM EFR speech codec D500h-F7FFh Reserved F800h-FBFFh Bootloader FC00h-FCFFh µ-Law expansion table FD00h-FDFFh A-Law expansion table FE00h-FEFFh Sine look-up table FF00h-FF7Fh Reserved (1) FF80h-FFFFh Interrupt vector table (1) 3.3 In the ROM, 128 words are reserved for factory device-testing purposes. Application code to be implemented in on-chip ROM must reserve these 128 words at addresses FF00h-FF7Fh in program space. On-Chip RAM The device contains 64K-word × 16-bit of on-chip dual-access RAM (DARAM) and 64K-word × 16-bit of on-chip single-access RAM (SARAM). The DARAM is composed of eight blocks of 8K words each. Each block in the DARAM can support two reads in one cycle, or a read and a write in one cycle. Four blocks of DARAM are located in the address range 0080h-7FFFh in data space, and can be mapped into program/data space by setting the OVLY bit to one. The other four blocks of DARAM are located in the address range 18000h-1FFFFh in program space. The DARAM located in the address range 18000h-1FFFFh in program space can be mapped into data space by setting the DROM bit to one. The SARAM is composed of eight blocks of 8K words each. Each of these eight blocks is a single-access memory. For example, an instruction word can be fetched from one SARAM block in the same cycle as a data word is written to another SARAM block. The SARAM is located in the address range 28000h-2FFFFh, and 38000h-3FFFFh in program space. 3.4 On-Chip Memory Security The device has a maskable option to protect the contents of on-chip memories. When the RAM/ROM security option is selected, the following restrictions apply: • Only the on-chip ROM originating instructions can read the contents of the on-chip ROM; on-chip RAM and external RAM originating instruction can not read data from ROM: instead 0FFFFh is read. Code can still branch to ROM from on-chip RAM or external program memory. • The contents of on-chip RAM can be read by all instructions, even by instructions fetched from external memory. To protect the internal RAM, the user must never branch to external memory. • The security feature completely disables the scan-based emulation capability of the 54x to prevent the use of a debugger utility. This only affects emulation and does not prevent the use of the JTAG boundary scan test capability. • The device is internally forced into microcomputer mode at reset (MP/MC bit forced to zero), preventing the ROM from being disabled by the external MP/MC pin. The status of the MP/MC bit in the PMST register can be changed after reset by the user application. • HPI writes have no restriction, but HPI reads are restricted to the 4000h - 5FFFh address range. Submit Documentation Feedback Functional Overview 19 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com If the ROM-only security option is selected the following restrictions apply: • Only the on-chip ROM originating instructions can read the contents of the on-chip ROM; on-chip RAM and external RAM originating instruction cannot read data from ROM: instead 0FFFFh is read. Code can still branch to ROM from on-chip RAM or external program memory. • The contents of on-chip RAM can be read by all instructions, even by instructions fetched from external memory. To protect the internal RAM the user must never branch to external memory. • The security feature completely disables the scan-based emulation capability of the 54x to prevent the use of a debugger utility. This only affects emulation and does not prevent the use of the JTAG boundary scan test capability. • The device can be started in either microcomputer mode or microprocessor mode at reset (depends on the MP/MC pin). • HPI read and writes have no restriction. 3.5 Memory Map The program and data memory map is shown in Figure 3-2. Address ranges for on-chip DARAM in data memory are: • DARAM0: 0080h-1FFFh • DARAM1: 2000h-3FFFh • DARAM2: 4000h-5FFFh • DARAM3: 6000h-7FFFh • DARAM4: 8000h-9FFFh • DARAM5: A000h-BFFFh • DARAM6: C000h-DFFFh • DARAM7: E000h-FFFFh Hex Page 0 Program 0000 Reserved (OVLY = 1) External (OVLY = 0) 007F On-Chip 0080 DARAM0−3 (OVLY = 1) External 7FFF (OVLY = 0) 8000 External FF7F FF80 Interrupts (External) FFFF MP/MC= 1 (Microprocessor Mode) Hex Page 0 Program 0000 Reserved (OVLY = 1) External (OVLY = 0) 007F 0080 7FFF 8000 BFFF C000 FEFF FF00 FF7F FF80 FFFF On-Chip DARAM0−3 (OVLY = 1) External (OVLY = 0) External Hex 0000 005F 0060 007F 0080 7FFF 8000 On-Chip ROM (4K x 16-bit) Reserved Interrupts (On-Chip) MP/MC= 0 (Microcomputer Mode) Data Memory-Mapped Registers Scratch-Pad RAM On-Chip DARAM0−3 (32K x 16-bit) On-Chip DARAM4−7 (DROM=1) or External (DROM=0) FFFF Figure 3-2. Program and Data Memory Map 20 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 The extended program memory map is shown in Figure 3-3. Address ranges for on-chip DARAM in data memory are: • DARAM4: 018000h-019FFFh • DARAM5: 01A000h-01BFFFh • DARAM6: 01C000h-01DFFFh • DARAM7: 01E000h-01FFFFh Address ranges for on-chip SARAM in program memory are: • SARAM0: 028000h-029FFFh • SARAM1: 02A000h-02BFFFh • SARAM2: 02C000h-02DFFFh • SARAM3: 02E000h-02FFFFh • SARAM4: 038000h-039FFFh • SARAM5: 03A000h-03BFFFh • SARAM6: 03C000h-03DFFFh • SARAM7: 03E000h-03FFFFh Hex 010000 Program Program On-Chip DARAM0−3 (OVLY=1) External (OVLY=0) 017FFF Hex 020000 018000 On-Chip SARAM0−3 (MP/MC=0) External (MP/MC=1) On-Chip DARAM4−7 (MP/MC=0) External (MP/MC=1) 01FFFF Program On-Chip DARAM0−3 (OVLY=1) External (OVLY=0) 027FFF Hex 030000 On-Chip DARAM0−3 (OVLY=1) External (OVLY=0) 037FFF On-Chip DARAM0−3 (OVLY=1) External (OVLY=0) 047FFF 028000 038000 On-Chip SARAM4−7 (MP/MC=0) External (MP/MC=1) 048000 02FFFF Page 1 XPC=1 03FFFF Page 2 XPC=2 Hex 040000 Program On-Chip DARAM0−3 (OVLY=1) External 7F7FFF (OVLY=0) ...... 7F8000 External External 7FFFFF 04FFFF Page 3 XPC=3 Hex 7F0000 Program Page 127 XPC=7Fh Page 4 XPC=4 Figure 3-3. Extended Program Memory Map 3.5.1 Relocatable Interrupt Vector Table The reset, interrupt, and trap vectors are addressed in program space. These vectors are soft — meaning that the processor, when taking the trap, loads the program counter (PC) with the trap address and executes the code at the vector location. Four words, either two 1-word instructions or one 2-word instruction, are reserved at each vector location to accommodate a delayed branch instruction which allows branching to the appropriate interrupt service routine without the overhead. At device reset, the reset, interrupt, and trap vectors are mapped to address FF80h in program space. However, these vectors can be remapped to the beginning of any 128-word page in program space after device reset. This is done by loading the interrupt vector pointer (IPTR) bits in the PMST register with the appropriate 128-word page boundary address. After loading IPTR, any user interrupt or trap vector is mapped to the new 128-word page. NOTE The hardware reset (RS) vector cannot be remapped because the hardware reset loads the IPTR with 1s. Therefore, the reset vector is always fetched at location FF80h in program space. Submit Documentation Feedback Functional Overview 21 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 15 8 IPTR R/W-1FF 7 6 5 4 3 2 1 0 IPTR MP/MC OVLY AVIS DROM CLKOFF SMUL SST MP/MC pin R/W-0 R/W-0 LEGEND: R = Read, W = Write, n = value present after reset R/W-0 R/W-0 R/W-0 R/W-0 Figure 3-4. Process Mode Status Register Table 3-2. Processor Mode Status (PMST) Register Bit Fields BIT NO. 15-7 6 5 22 NAME RESET VALUE FUNCTION 1FFh Interrupt vector pointer. The 9-bit IPTR field points to the 128-word program page where the interrupt vectors reside. The interrupt vectors can be remapped to RAM for boot-loaded operations. At reset, these bits are all set to 1; the reset vector always resides at address FF80h in program memory space. The RESET instruction does not affect this field. IPTR MP/MC Microprocessor/microcomputer mode. MP/MC enables/disables the on-chip ROM to be addressable in program memory space. • MP/MC = 0: The on-chip ROM is enabled and addressable. MP/MC • MP/MC = 1: The on-chip ROM is not available. pin MP/MC is set to the value corresponding to the logic level on the MP/MC pin when sampled at reset. This pin is not sampled again until the next reset. The RESET instruction does not affect this bit. This bit can also be set or cleared by software. OVLY 0 RAM overlay. OVLY enables on-chip dual-access data RAM blocks to be mapped into program space. The values for the OVLY bit are: • OVLY = 0: The on-chip RAM is addressable in data space but not in program space. • OVLY = 1: The on-chip RAM is mapped into program space and data space. Data page 0 (addresses 0h to 7Fh), however, is not mapped into program space. 4 AVIS 0 Address visibility mode. AVIS enables/disables the internal program address to be visible at the address pins. • AVIS = 0: The external address lines do not change with the internal program address. Control and data lines are not affected and the address bus is driven with the last address on the bus. • AVIS = 1: This mode allows the internal program address to appear at the pins of the device so that the internal program address can be traced. Also, it allows the interrupt vector to be decoded in conjunction with IACK when the interrupt vectors reside on on-chip memory. 3 DROM 0 DROM enables on-chip DARAM4-7 to be mapped into data space. The DROM bit values are: • DROM = 0: The on-chip DARAM4-7 is not mapped into data space. • DROM = 1: The on-chip DARAM4-7 is mapped into data space. 2 CLKOFF 0 CLOCKOUT off. When the CLKOFF bit is 1, the output of CLKOUT is disabled and remains at a high level. 1 SMUL N/A Saturation on multiplication. When SMUL = 1, saturation of a multiplication result occurs before performing the accumulation in a MAC of MAS instruction. The SMUL bit applies only when OVM = 1 and FRCT = 1. 0 SST N/A Saturation on store. When SST = 1, saturation of the data from the accumulator is enabled before storing in memory. The saturation is performed after the shift operation. Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 3.6 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 On-Chip Peripherals The device has the following peripherals: • Software-programmable wait-state generator • Programmable bank-switching • A host-port interface (HPI8/16) • Three multichannel buffered serial ports (McBSPs) • A hardware timer • A clock generator with a multiple phase-locked loop (PLL) • Enhanced external parallel interface (XIO2) • A DMA controller (DMA) 3.6.1 Software-Programmable Wait-State Generator The software wait-state generator of the device can extend external bus cycles by up to fourteen machine cycles. Devices that require more than fourteen wait states can be interfaced using the hardware READY line. When all external accesses are configured for zero wait states, the internal clocks to the wait-state generator are automatically disabled. Disabling the wait-state generator clocks reduces the power consumption. The software wait-state register (SWWSR) controls the operation of the wait-state generator. The 14 LSBs of the SWWSR specify the number of wait states (0 to 7) to be inserted for external memory accesses to five separate address ranges. This allows a different number of wait states for each of the five address ranges. Additionally, the software wait-state multiplier (SWSM) bit of the software wait-state control register (SWCR) defines a multiplication factor of 1 or 2 for the number of wait states. At reset, the wait-state generator is initialized to provide seven wait states on all external memory accesses. The SWWSR bit fields are shown in Figure 3-5 and described in Table 3-3. 15 14 12 11 9 XPA I/O DATA R/W-0 R/W-111 R/W-111 7 6 DATA 5 3 PROGRAM R/W-111 R/W-111 LEGEND: R = Read, W = Write, n = value present after reset 8 DATA 2 0 PROGRAM R/W-111 Figure 3-5. Software Wait-State Register (SWWSR) [Memory-Mapped Register (MMR) Address 0028h] Submit Documentation Feedback Functional Overview 23 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Table 3-3. Software Wait-State Register (SWWSR) Bit Fields BIT NO. NAME RESET VALUE 15 XPA 0 14-12 I/O 111 I/O space. The field value (0-7) corresponds to the base number of wait states for I/O space accesses within addresses 0000-FFFFh. The SWSM bit of the SWCR defines a multiplication factor of 1 or 2 for the base number of wait states. 11-9 Data 111 Upper data space. The field value (0-7) corresponds to the base number of wait states for external data space accesses within addresses 8000-FFFFh. The SWSM bit of the SWCR defines a multiplication factor of 1 or 2 for the base number of wait states. 8-6 Data 111 Lower data space. The field value (0-7) corresponds to the base number of wait states for external data space accesses within addresses 0000-7FFFh. The SWSM bit of the SWCR defines a multiplication factor of 1 or 2 for the base number of wait states. 5-3 Program 111 FUNCTION Extended program address control bit. XPA is used in conjunction with the program space fields (bits 0 through 5) to select the address range for program space wait states. Upper program space. The field value (0-7) corresponds to the base number of wait states for external program space accesses within the following addresses: • XPA = 0: xx8000 - xxFFFFh • XPA = 1: 400000h - 7FFFFFh The SWSM bit of the SWCR defines a multiplication factor of 1 or 2 for the base number of wait states. 2-0 Program 111 Program space. The field value (0-7) corresponds to the base number of wait states for external program space accesses within the following addresses: • XPA = 0: xx0000 - xx7FFFh • XPA = 1: 000000 - 3FFFFFh. The SWSM bit of the SWCR defines a multiplication factor of 1 or 2 for the base number of wait states. The software wait-state multiplier bit of the software wait-state control register (SWCR) is used to extend the base number of wait states selected by the SWWSR. The SWCR bit fields are shown in Figure 3-6 and described in Table 3-4. 15 8 Reserved R/W-0 7 1 Reserved 0 SWSM R/W-0 LEGEND: R = Read, W = Write, n = value present after reset R/W-0 Figure 3-6. Software Wait-State Register (SWWSR) [Memory-Mapped Register (MMR) Address 0028h] Table 3-4. Software Wait-State Control Register (SWCR) Bit Fields PIN NO. NAME RESET VALUE 15-1 Reserved 0 These bits are reserved and are unaffected by writes. 0 Software wait-state multiplier. Used to multiply the number of wait states defined in the SWWSR by a factor of 1 or 2. • SWSM = 0: wait-state base values are unchanged (multiplied by 1) • SWSM = 1: wait-state base values are multiplied by 2 for a maximum of 14 wait states 0 24 SWSM Functional Overview FUNCTION Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 3.6.2 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Programmable Bank-Switching Programmable bank-switching logic allows the device to switch between external memory banks without requiring external wait states for memories that need additional time to turn off. The bank-switching logic automatically inserts one cycle when accesses cross a 32K-word memory-bank boundary inside program or data space. Bank-switching is defined by the bank-switching control register (BSCR), which is memory-mapped ataddress 0029h. The bit fields of the BSCR are shown in Figure 3-7 and are described in Table 3-5. 15 14 13 12 11 8 CONSEC DIVFCT IACKOFF Reserved R/W-1 R/W-11 R/W-1 R 7 3 2 1 0 HBH BH Reserved R/W-0 R/W-0 R Reserved R LEGEND: R = Read, W = Write, n = value present after reset Figure 3-7. Bank-Switching Control Register BSCR)[MMR Address 0029h] Table 3-5. Bank-Switching Control Register (BSCR) Fields BIT 15 14-13 12 11-3 2 (1) NAME RESET VALUE FUNCTION 1 Consecutive bank-switching. Specifies the bank-switching mode. • CONSEC = 0: Bank-switching on 32K bank boundaries only. This bit is cleared if fast access is desired for continuous memory reads (i.e., no starting and trailing cycles between read cycles). • CONSEC = 1: Consecutive bank switches on external memory reads. Each read cycle consists of 3 cycles: starting cycle, read cycle, and trailing cycle. DIVFCT 11 CLKOUT output divide factor. The CLKOUT output is driven by an on-chip source having a frequency equal to 1/(DIVFCT+1) of the DSP clock. • DIVFCT = 00: CLKOUT is not divided. • DIVFCT = 01: CLKOUT is divided by 2 from the DSP clock. • DIVFCT = 10: CLKOUT is divided by 3 from the DSP clock. • DIVFCT = 11: CLKOUT is divided by 4 from the DSP clock (default value following reset). IACKOFF 11 IACK signal output off. Controls the output of the IACK signal. IACKOFF is set to 1 at reset. • IACKOFF = 0: The IACK signal output off function is disabled. • IACKOFF = 1: The IACK signal output off function is enabled. CONSEC (1) Rsvd Reserved HBH 0 HPI bus holder. Controls the HPI bus holder. HBH is cleared to 0 at reset. • HBH = 0: The bus holder is disabled except when HPI16 = 1. • HBH = 1: The bus holder is enabled. When not driven, the HPI data bus, HD[7:0] is held in the previous logic level. 0 Bus holder. Controls the bus holder. BH is cleared to 0 at reset. • BH = 0: The bus holder is disabled. • BH = 1: The bus holder is enabled. When not driven, the data bus, D[15:0] is held in the previous logic level. 1 BH 0 Rsvd Reserved For additional information, see Section 3.11 of this document. Submit Documentation Feedback Functional Overview 25 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com The device has an internal register that holds the MSB of the last address used for a read or write operation in program or data space. In the non-consecutive bank switches (CONSEC = 0), if the MSB of the address used for the current read does not match that contained in this internal register, the MSTRB (memory strobe) signal is not asserted for one CLKOUT cycle. During this extra cycle, the address bus switches to the new address. The contents of the internal register are replaced with the MSB for the read of the current address. If the MSB of the address used for the current read matches the bits in the register, a normal read cycle occurs. In non-consecutive bank switches (CONSEC = 0), if repeated reads are performed from the same memory bank, no extra cycles are inserted. When a read is performed from a different memory bank, memory conflicts are avoided by inserting an extra cycle. For more information, see Section 3.11 of this document. The bank-switching mechanism automatically inserts one extra cycle in the following cases: • A memory read followed by another memory read from a different memory bank. • A program-memory read followed by a data-memory read. • A data-memory read followed by a program-memory read. • A program-memory read followed by another program-memory read from a different page. 3.6.3 Bus Holders The device has two bus holder control bits, BH (BSCR[1]) and HBH (BSCR[2]), to control the bus keepers of the address bus (A[17-0]), data bus (D[15-0]), and the HPI data bus (HD[7-0]). Bus keeper enabling/disabling is described in Table 3-6. Table 3-6. Bus Holder Control Bits 3.7 HPI16 PIN BH HBH D[15-0] A[17-0] HD[7-0] 0 0 0 OFF OFF OFF 0 0 1 OFF OFF ON 0 1 0 ON OFF OFF 0 1 1 ON OFF ON 1 0 0 OFF OFF ON 1 0 1 OFF ON ON 1 1 0 ON OFF ON 1 1 1 ON ON ON Parallel I/O Ports The device has a total of 64K I/O ports. These ports can be addressed by the PORTR instruction or the PORTW instruction. The IS signal indicates a read/write operation through an I/O port. The device can interface easily with external devices through the I/O ports while requiring minimal off-chip address-decoding circuits. 26 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 3.7.1 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Enhanced 8-/16-Bit Host-Port Interface (HPI8/16) The host-port interface, also referred to as the HPI8/16, is an enhanced version of the standard 8-bit HPI found on earlier TMS320C54x™ DSPs (542, 545, 548, and 549). The HPI can be used to interface to an 8-bit or 16-bit host. When the address and data buses for external I/O is not used (to interface to external devices in program/data/IO spaces), the HPI can be configured as an HPI16 to interface to a 16-bit host. This configuration can be accomplished by connecting the HPI16 pin to logic "1”. When the HPI16 pin is connected to a logic "0", the HPI is configured as an HPI8. The HPI8 is an 8-bit parallel port for interprocessor communication. The features of the HPI8 include: Standard features: • Sequential transfers (with autoincrement) or random-access transfers • Host interrupt and C54x™ interrupt capability • Multiple data strobes and control pins for interface flexibility The HPI8 interface consists of an 8-bit bidirectional data bus and various control signals. Sixteen-bit transfers are accomplished in two parts with the HBIL input designating high or low byte. The host communicates with the HPI8 through three dedicated registers — the HPI address register (HPIA), the HPI data register (HPID), and the HPI control register (HPIC). The HPIA and HPID registers are only accessible by the host, and the HPIC register is accessible by both the host and the device. Enhanced features: • Access to entire on-chip RAM through DMA bus • Capability to continue transferring during emulation stop The HPI16 is an enhanced 16-bit version of the TMS320C54x™ DSP 8-bit host-port interface (HPI8). The HPI16 is designed to allow a 16-bit host to access the DSP on-chip memory, with the host acting as the master of the interface. Some of the features of the HPI16 include: • 16-bit bidirectional data bus • Multiple data strobes and control signals to allow glueless interfacing to a variety of hosts • Only nonmultiplexed address/data modes are supported • 18-bit address bus used in nonmultiplexed mode to allow access to all internal memory (including internal extended address pages) • HRDY signal to hold off host accesses due to DMA latency • The HPI16 acts as a slave to a 16-bit host processor and allows access to the on-chip memory of the DSP. NOTE Only the nonmultiplexed mode is supported when the HPI is configured as a HPI16. The HPI functions as a slave and enables the host processor to access the on-chip memory. A major enhancement to the HPI over previous versions is that it allows host access to the entire on-chip memory range of the DSP. The host and the DSP both have access to the on-chip RAM at all times and host accesses are always synchronized to the DSP clock. If the host and the DSP contend for access to the same location, the host has priority, and the DSP waits for one cycle. Note that since host accesses are always synchronized to the device clock, an active input clock (CLKIN) is required for HPI accesses during IDLE states, and host accesses are not allowed while the device reset pin is asserted. Submit Documentation Feedback Functional Overview 27 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 3.7.2 www.ti.com HPI Nonmultiplexed Mode In nonmultiplexed mode, a host with separate address/data buses can access the HPI16 data register (HPID) via the HD 16-bit bidirectional data bus, and the address register (HPIA) via the 18-bit HA address bus. The host initiates the access with the strobe signals (HDS1, HDS2, HCS) and controls the direction of the access with the HR/W signal. The HPI16 can stall host accesses via the HRDY signal. Note that the HPIC register is not available in nonmultiplexed mode since there are no HCNTL signals available. All host accesses initiate a DMA read or write access. Figure 3-8 shows a block diagram of the HPI16 in nonmultiplexed mode. Figure 3-9 shows the HPI memory map. DATA[15:0] HPI16 PPD[15:0] HINT HPID[15:0] DMA Address[17:0] Internal Memory HOST HCNTL0 VCC HCNTL1 HBIL HAS R/W HR/W Data Strobes READY HRDY 54xx CPU HDS1, HDS2, HCS Figure 3-8. Host-Port Interface — Nonmulltiplexed Mode 28 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Address (Hex) 000 0000 Reserved 000 005F 000 0060 000 007F 000 0080 Scratch-Pad RAM DARAM0 − DARAM3 000 7FFF 000 8000 Reserved 001 7FFF 001 8000 DARAM4 − DARAM7 001 FFFF 002 0000 Reserved 002 7FFF 002 8000 002 FFFF 003 0000 SARAM0 − SARAM3 Reserved 003 7FFF 003 8000 SARAM4 − SARAM7 003 FFFF 004 0000 Reserved 07F FFFF Figure 3-9. HPI Memory Map Submit Documentation Feedback Functional Overview 29 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 3.8 www.ti.com Multichannel Buffered Serial Ports (McBSPs) The device provides three high-speed, full-duplex, multichannel buffered serial ports that allow direct interface to other C54x/LC54x devices, codecs, and other devices in a system. The McBSPs are based on the standard serial-port interface found on other 54x devices. Like their predecessors, the McBSPs provide: • Full-duplex communication • Double-buffer data registers, which allow a continuous data stream • Independent framing and clocking for receive and transmit In addition, the McBSPs have the following capabilities: • Direct interface to: – T1/E1 framers – MVIP switching compatible and ST-BUS compliant devices – IOM-2 compliant devices – AC97-compliant devices – IIS-compliant devices – Serial peripheral interface • Multichannel transmit and receive of up to 128 channels • A wide selection of data sizes, including 8, 12, 16, 20, 24, or 32 bits • µ-law and A-law companding • Programmable polarity for both frame synchronization and data clocks • Programmable internal clock and frame generation The McBSP consists of a data path and control path. The six pins, BDX, BDR, BFSX, BFSR, BCLKX, and BCLKR, connect the control and data paths to external devices. The implemented pins can be programmed as general-purpose I/O pins if they are not used for serial communication. The data is communicated to devices interfacing to the McBSP by way of the data transmit (BDX) pin for transmit and the data receive (BDR) pin for receive. The CPU or DMA reads the received data from the data receive register (DRR) and writes the data to be transmitted to the data transmit register (DXR). Data written to the DXR is shifted out to BDX by way of the transmit shift register (XSR). Similarly, receive data on the BDR pin is shifted into the receive shift register (RSR) and copied into the receive buffer register (RBR). RBR is then copied to DRR, which can be read by the CPU or DMA. This allows internal data movement and external data communications simultaneously. Control information in the form of clocking and frame synchronization is communicated by way of BCLKX, BCLKR, BFSX, and BFSR. The device communicates to the McBSP by way of 16-bit-wide control registers accessible via the internal peripheral bus. The control block consists of internal clock generation, frame synchronization signal generation, and their control, and multichannel selection. This control block sends notification of important events to the CPU and DMA by way of two interrupt signals, XINT and RINT, and two event signals, XEVT and REVT. The on-chip companding hardware allows compression and expansion of data in either µ-law or A-law format. When companding is used, transmitted data is encoded according to the specified companding law and received data is decoded to 2s complement format. The sample rate generator provides the McBSP with several means of selecting clocking and framing for both the receiver and transmitter. Both the receiver and transmitter can select clocking and framing independently. 30 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 The McBSP allows the multiple channels to be independently selected for the transmitter and receiver. When multiple channels are selected, each frame represents a time-division multiplexed (TDM) data stream. In using time-division multiplexed data streams, the CPU may only need to process a few of them. Thus, to save memory and bus bandwidth, multichannel selection allows independent enabling of particular channels for transmission and reception. All 128 channels in a bit stream consisting of a maximum of 128 channels can be enabled. 15 10 7 6 XPBBLK 9 8 Reserved XMCME XPBBLK R R/W R/W 5 4 XPABLK R/W R/W LEGEND: R = Read, W = Write, n = value present after reset 1 0 XCBLK 2 Reserved XMCM R R R/W Figure 3-10. Multichannel Control Register (MCR1) 15 10 7 6 RPBBLK 9 8 Reserved RMCME RPBBLK R R/W R/W 5 4 RPABLK R/W R/W LEGEND: R = Read, W = Write, n = value present after reset 1 0 RCBLK 2 Reserved RMCM R R R/W Figure 3-11. Multichannel Control Register (MCR2) The McBSP has two working modes: • In the first mode, when (R/X)MCME = 0, it is comparable with the McBSPs used in the 5410 where the normal 32-channel selection is enabled (default). • In the second mode, when (R/X)MCME = 1, it has 128-channel selection capability. Multichannel control register Bit 9, (R/X)MCME, is used as the 128-channel selection enable bit. Once (R/X)MCME = 1, twelve new registers ((R/X)CERC - (R/X)CERH) are used to enable the 128-channel selection. The clock stop mode (CLKSTP) in the McBSP provides compatibility with the serial port interface protocol. Clock stop mode works with only single-phase frames and one word per frame. The word sizes supported by the McBSP are programmable for 8-, 12-, 16-, 20-, 24-, or 32-bit operation. When the McBSP is configured to operate in SPI mode, both the transmitter and the receiver operate together as a master or as a slave. Although the BCLKS pin is not available on the device PGE and GGU packages, the device is capable of synchronization to external clock sources. BCLKX or BCLKR can be used by the sample rate generator for external synchronization. The sample rate clock mode extended (SCLKME) bit field is located in the PCR to accommodate this option. 15 13 12 11 10 9 8 Reserved 14 XIOEN RIOEN FSXM FSRM CLKXM CLKRM R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 SCLKME CLKS STAT DX STAT DR STAT FSXP FSRP CLKXP CLKRP R/W R/W R/W R/W R/W R/W R/W R/W LEGEND: R = Read, W = Write, n = value present after reset Figure 3-12. Pin Control Register (PCR) Submit Documentation Feedback Functional Overview 31 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com The selection of sample rate input clock is made by the combination of the CLKSM (bit 13 in SRGR2) bit value and the SCLKME bit value as shown in Table 3-7. Table 3-7. Sample Rate Input Clock Selection SCLKME CLKSM SAMPLE RATE CLOCK MODE 0 0 Reserved (CLKS pin unavailable) 0 1 CPU clock 1 0 BCLKR 1 1 BCLKX When the SCLKME bit is cleared to 0, the CLKSM bit is used, as before, to select either the CPU clock or the CLKS pin (not bonded out on the device package) as the sample rate input clock. Setting the SCLKME bit to 1 enables the CLKSM bit to select between the BCLKR pin or BCLKX pin for the sample rate input clock. When either the BCLKR or CLKX is configured this way, the output buffer for the selected pin is automatically disabled. For example, with SCLKME = 1 and CLKSM = 0, the BCLKR pin is configured as the input of the sample rate generator. Both the transmitter and receiver circuits can be synchronized to the sample rate generator output by setting the CLKXM and CLKRM bits of the pin configuration register (PCR) to 1. Note that the sample rate generator output will only be driven on the BCLKX pin since the BCLKR output buffer is automatically disabled. The McBSP is fully static and operates at arbitrary low clock frequencies. For maximum operating frequency, see Section 5.5.10. 3.9 Hardware Timer The device features a 16-bit timing circuit with a 4-bit prescaler. The timer counter is decremented by one every CLKOUT cycle. Each time the counter decrements to 0, a timer interrupt is generated. The timer can be stopped, restarted, reset, or disabled by specific status bits. 3.10 Clock Generator The clock generator provides clocks to the device, and consists of a phase-locked loop (PLL) circuit. The clock generator requires a reference clock input, which can be provided from an external clock source. The reference clock input is then divided by two (DIV mode) to generate clocks for the device, or the PLL circuit can be used (PLL mode) to generate the device clock by multiplying the reference clock frequency by a scale factor, allowing use of a clock source with a lower frequency than that of the CPU. The PLL is an adaptive circuit that, once synchronized, locks onto and tracks an input clock signal. When the PLL is initially started, it enters a transitional mode during which the PLL acquires lock with the input signal. Once the PLL is locked, it continues to track and maintain synchronization with the input signal. Then, other internal clock circuitry allows the synthesis of new clock frequencies for use as master clock for the device. 32 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 This clock generator allows system designers to select the clock source. The sources that drive the clock generator are: • A crystal resonator circuit. The crystal resonator circuit is connected across the X1 and X2/CLKIN pins of the device to enable the internal oscillator. • An external clock. The external clock source is directly connected to the X2/CLKIN pin, and X1 is left unconnected. NOTE The crystal oscillator function is not supported by all die revisions of the device. See the TMS320VC5416 Digital Signal Processor Silicon Errata (literature number SPRZ172) to verify which die revisions support this functionality. The software-programmable PLL features a high level of flexibility, and includes a clock scaler that provides various clock multiplier ratios, capability to directly enable and disable the PLL, and a PLL lock timer that can be used to delay switching to PLL clocking mode of the device until lock is achieved. Devices that have a built-in software-programmable PLL can be configured in one of two clock modes: • PLL mode. The input clock (X2/CLKIN) is multiplied by 1 of 31 possible ratios. • DIV (divider) mode. The input clock is divided by 2 or 4. Note that when DIV mode is used, the PLL can be completely disabled in order to minimize power dissipation. The software-programmable PLL is controlled using the 16-bit memory-mapped (address 0058h) clock mode register (CLKMD). The CLKMD register is used to define the clock configuration of the PLL clock module. Note that upon reset, the CLKMD register is initialized with a predetermined value dependent only upon the state of the CLKMD1 - CLKMD3 pins. For more programming information, see the TMS320C54x DSP Reference Set, Volume 1: CPU and Peripherals (literature number SPRU131). The CLKMD pin configured clock options are shown in Table 3-8. Table 3-8. Clock Mode Settings at Reset (1) CLKMD RESET VALUE CLOCK MODE (1) CLKMD1 CLKMD2 CLKMD3 0 0 0 0000h 1/2 (PLL disabled) 0 0 1 9007h PLL x 10 0 1 0 4007h PLL x 5 1 0 0 1007h PLL x 2 1 1 0 F007h PLL x 1 1 1 1 0000h 1/2 (PLL disabled) 1 0 1 F000h 1/4 (PLL disabled) 0 1 1 — Reserved (Bypass mode) The external CLKMD1-CLKMD3 pins are sampled to determine the desired clock generation mode while RS is low. Following reset, the clock generation mode can be reconfigured by writing to the internal clock mode register in software. Submit Documentation Feedback Functional Overview 33 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 3.11 Enhanced External Parallel Interface (XIO2) The device external interface has been redesigned to include several improvements, including: simplification of the bus sequence, more immunity to bus contention when transitioning between read and write operations, the ability for external memory access to the DMA controller, and optimization of the power-down modes. The bus sequence on the device still maintains all of the same interface signals as on previous 54x devices, but the signal sequence has been simplified. Most external accesses now require 3 cycles composed of a leading cycle, an active (read or write) cycle, and a trailing cycle. The leading and trailing cycles provide additional immunity against bus contention when switching between read operations and write operations. To maintain high-speed read access, a consecutive read mode that performs single-cycle reads as on previous 54x devices is available. Figure 3-13 shows the bus sequence for three cases: all I/O reads, memory reads in nonconsecutive mode, or single memory reads in consecutive mode. The accesses shown in Figure 3-13 always require 3 CLKOUT cycles to complete. CLKOUT A[22:0] D[15:0] READ R/W MSTRB or IOSTRB PS/DS/IS Leading Cycle Read Cycle Trailing Cycle Figure 3-13. Nonconsecutive Memory Read and I/O Read Bus Sequence 34 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Figure 3-14 shows the bus sequence for repeated memory reads in consecutive mode. The accesses shown in Figure 3-14 require (2 + n) CLKOUT cycles to complete, where n is the number of consecutive reads performed. CLKOUT A[22:0] D[15:0] READ READ READ R/W MSTRB PS/DS Leading Cycle Read Cycle Read Cycle Read Cycle Trailing Cycle Figure 3-14. Consecutive Memory Read Bus Sequence (n = 3 reads) Submit Documentation Feedback Functional Overview 35 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Figure 3-15 shows the bus sequence for all memory writes and I/O writes. The accesses shown in Figure 3-15 always require 3 CLKOUT cycles to complete. CLKOUT A[22:0] D[15:0] WRITE R/W MSTRB or IOSTRB PS/DS/IS Leading Cycle Write Cycle Trailing Cycle Figure 3-15. Memory Write and I/O Write Bus Sequence The enhanced interface also provides the ability for DMA transfers to extend to external memory. For more information on DMA capability, see the DMA sections that follow. The enhanced interface improves the low-power performance already present on the TMS320C5000™ DSP platform by switching off the internal clocks to the interface when it is not being used. This power-saving feature is automatic, requires no software setup, and causes no latency in the operation of the interface. Additional features integrated in the enhanced interface are the ability to automatically insert bank-switching cycles when crossing 32K memory boundaries (see Section 3.6.2), the ability to program up to 14 wait states through software (see Section 3.6.1), and the ability to divide down CLKOUT by a factor of 1, 2, 3, or 4. Dividing down CLKOUT provides an alternative to wait states when interfacing to slower external memory or peripheral devices. While inserting wait states extends the bus sequence during read or write accesses, it does not slow down the bus signal sequences at the beginning and the end of the access. Dividing down CLKOUT provides a method of slowing the entire bus sequence when necessary. The CLKOUT divide-down factor is controlled through the DIVFCT field in the bank-switching control register (BSCR) (see Table 3-5). 36 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 3.12 DMA Controller The device direct memory access (DMA) controller transfers data between points in the memory map without intervention by the CPU. The DMA allows movements of data to and from internal program/data memory, internal peripherals (such as the McBSPs), or external memory devices to occur in the background of CPU operation. The DMA has six independent programmable channels, allowing six different contexts for DMA operation. 3.12.1 Features The DMA has the following features: • The DMA operates independently of the CPU. • The DMA has six channels. The DMA can keep track of the contexts of six independent block transfers. • The DMA has higher priority than the CPU for both internal and external accesses. • Each channel has independently programmable priorities. • Each channel's source and destination address registers can have configurable indexes through memory on each read and write transfer, respectively. The address may remain constant, be post-incremented, be post-decremented, or be adjusted by a programmable value. • Each read or write internal transfer may be initialized by selected events. • On completion of a half- or entire-block transfer, each DMA channel may send an interrupt to the CPU. • The DMA can perform double-word internal transfers (a 32-bit transfer of two 16-bit words). 3.12.2 DMA External Access The DMA supports external accesses to data, I/O, and extended program memory. These overlay pages are only visible to the DMA controller. A maximum of two DMA channels can be used for external memory accesses. The DMA external accesses require a minimum of 8 cycles for external writes and a minimum of 11 cycles for external reads assuming the XIO02 is in consecutive mode (CONSEC = 1), wait state is set to two, and CLKOUT is not divided (DIVFCT = 00). The control of the bus is arbitrated between the CPU and the DMA. While the DMA or CPU is in control of the external bus, the other will be held-off via wait states until the current transfer is complete. The DMA takes precedence over XIO requests. • Only two channels are available for external accesses. (One for external reads and one for external writes.) • Single-word (16-bit) transfers are supported for external accesses. • The DMA does not support transfers from the peripherals to external memory. • The DMA does not support transfers from external memory to the peripherals. • The DMA does not support external-to-external accesses. • The DMA does not support synchronized external accesses. 15 14 13 12 11 AUTOINIT DINM IMOD CTMOD SLAXS 5 4 7 6 DMS DLAXS 10 8 SIND 2 1 DIND 0 DMD LEGEND: R = Read, W = Write, n = value present after reset Figure 3-16. DMA Transfer Mode Control Register (DMMCRn) Submit Documentation Feedback Functional Overview 37 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com These new bit fields were created to allow the user to define the space-select for the DMA (internal/external). The functions of the DLAXS and SLAXS bits are as follows: • DLAXS(DMMCRn[5]) Destination – 0 = No external access (default internal) – 1 = External access • SLAXS(DMMCRn[11]) Source – 0 = No external access (default internal) – 1 = External access Table 3-9 lists the DMD bit values and their corresponding destination space. Table 3-9. DMD Section of the DMMCRn Register DMD Destination Space 00 PS 01 DS 10 I/O 11 Reserved For the CPU external access, software can configure the memory cells to reside inside or outside the program address map. When the cells are mapped into program space, the device automatically accesses them when their addresses are within bounds. When the address generation logic generates an address outside its bounds, the device automatically generates an external access. 38 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 3.12.3 DMA Memory Maps The DMA memory maps, shown in Figure 3-17 and Figure 3-18, allows the DMA transfer to be unaffected by the status of the MP/MC, DROM, and OVLY bits. Hex 0000 005F 0060 DLAXS = 0 SLAXS = 0 1FFF 2000 3FFF 4000 5FFF 6000 Program Hex 010000 Program Hex 0x0000 Program Reserved Hex xx0000 Program On-Chip DARAM0 8K Words On-Chip DARAM1 8K Words Reserved Reserved On-Chip DARAM2 8K Words On-Chip DARAM3 8K Words 7FFF 8000 017FFF 018000 019FFF 01A000 0x7FFF On-Chip DARAM 4 8K Words 0x8000 0x9FFF 0xA000 On-Chip DARAM 5 8K Words 01BFFF 01C000 On-Chip DARAM 6 8K Words Reserved 01DFFF 01E000 On-Chip DARAM 7 8K Words 01FFFF FFFF Page 0 Page 1 Reserved On-Chip SARAM 0/4 8K Words On-Chip SARAM 1/5 8K Words 0xBFFF 0xC000 On-Chip SARAM 2/6 8K Words 0xDFFF 0xE000 On-Chip SARAM 3/7 8K Words 0xFFFF xxFFFF Page 2 − 3 Page 4 − 127 Figure 3-17. On-Chip DMA Memory Map for Program Space (DLAXS = 0 and SLAXS = 0) Submit Documentation Feedback Functional Overview 39 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Data Space (0000 - 005F) Hex 0000 Reserved 001F 0020 DRR20 0021 DRR10 DXR20 0022 0023 DXR10 0024 Reserved 002F DRR22 0030 DRR12 0031 DXR22 0032 0033 DXR12 0034 Reserved 0035 RCERA2 0036 0037 XCERA2 0038 Reserved 0039 003A RECRA0 003B XECRA0 003C Reserved 003F DRR21 0040 0041 DRR11 0042 DXR21 0043 DXR11 0044 Reserved 0049 004A RCERA1 004B XCERA1 004C Reserved 005F www.ti.com Data Space I/O Space Hex 0000 0000 Data Space (See Breakout) 005F 0060 007F 0080 Scratch-Pad RAM 1FFF 2000 3FFF 4000 5FFF 6000 7FFF 8000 9FFF A000 BFFF C000 DFFF E000 FFFF On-Chip DARAM0 8K Words On-Chip DARAM1 8K Words On-Chip DARAM2 8K Words Reserved On-Chip DARAM3 8K Words On-Chip DARAM4 8K Words On-Chip DARAM5 8K Words On-Chip DARAM6 8K Words On-Chip DARAM7 8K Words FFFF Figure 3-18. On-Chip DMA Memory Map for Data and IO Space (DLAXS = 0 and SLAXS = 0) 3.12.4 DMA Priority Level Each DMA channel can be independently assigned high- or low-priority relative to each other. Multiple DMA channels that are assigned to the same priority level are handled in a round-robin manner. 3.12.5 DMA Source/Destination Address Modification The DMA provides flexible address-indexing modes for easy implementation of data management schemes such as autobuffering and circular buffers. Source and destination addresses can be indexed separately and can be post-incremented, post-decremented, or post-incremented with a specified index offset. 40 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 3.12.6 DMA in Autoinitialization Mode The DMA can automatically reinitialize itself after completion of a block transfer. Some of the DMA registers can be preloaded for the next block transfer through the DMA reload registers (DMGSA, DMGDA, DMGCR, and DMGFR). Autoinitialization allows: • Continuous operation: Normally, the CPU would have to reinitialize the DMA immediately after the completion of the current block transfers, but with the reload registers, it can reinitialize these values for the next block transfer any time after the current block transfer begins. • Repetitive operation:The CPU does not preload the reload register with new values for each block transfer but only loads them on the first block transfer. The DMA has been enhanced to expand the DMA reload register sets. Each DMA channel now has its own DMA reload register set. For example, the DMA reload register set for channel 0 has DMGSA0, DMGDA0, DMGCR0, and DMGFR0 while DMA channel 1 has DMGSA1, DMGDA1, DMGCR1, and DMGFR1, etc. To utilize the additional DMA reload registers, the AUTOIX bit is added to the DMPREC register as shown in Figure 3-19. 15 14 FREE AUTOIX 7 6 13 8 DPRC[5:0] 5 0 IOSEL DE[5:0] LEGEND: R = Read, W = Write, n = value present after reset Figure 3-19. DMPREC Register Table 3-10. DMA Reload Register Selection AUTOIX 0 (default) 1 DMA RELOAD REGISTER USAGE IN AUTO INIT MODE All DMA channels use DMGSA0, DMGDA0, DMGCR0 and DMGFR0 Each DMA channel uses its own set of reload registers 3.12.7 DMA Transfer Counting The DMA channel element count register (DMCTRx) and the frame count register (DMFRCx) contain bit fields that represent the number of frames and the number of elements per frame to be transferred. • Frame count. This 8-bit value defines the total number of frames in the block transfer. The maximum number of frames per block transfer is 128 (FRAME COUNT= 0FFh). The counter is decremented upon the last read transfer in a frame transfer. Once the last frame is transferred, the selected 8-bit counter is reloaded with the DMA global frame reload register (DMGFR) if the AUTOINIT bit is set to 1. A frame count of 0 (default value) means the block transfer contains a single frame. • Element count. This 16-bit value defines the number of elements per frame. This counter is decremented after the read transfer of each element. The maximum number of elements per frame is 65536 (DMCTRn = 0FFFFh). In autoinitialization mode, once the last frame is transferred, the counter is reloaded with the DMA global count reload register (DMGCR). 3.12.8 DMA Transfer in Doubleword Mode Doubleword mode allows the DMA to transfer 32-bit words in any index mode. In doubleword mode, two consecutive 16-bit transfers are initiated and the source and destination addresses are automatically updated following each transfer. In this mode, each 32-bit word is considered to be one element. Submit Documentation Feedback Functional Overview 41 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 3.12.9 DMA Channel Index Registers The particular DMA channel index register is selected by way of the SIND and DIND fields in the DMA transfer mode control register (DMMCRn). Unlike basic address adjustment, in conjunction with the frame index DMFRI0 and DMFRI1, the DMA allows different adjustment amounts depending on whether or not the element transfer is the last in the current frame. The normal adjustment value (element index) is contained in the element index registers DMIDX0 and DMIDX1. The adjustment value (frame index) for the end of the frame, is determined by the selected DMA frame index register, either DMFRI0 or DMFRI1. The element index and the frame index affect address adjustment as follows: • Element index: For all except the last transfer in the frame, the element index determines the amount to be added to the DMA channel for the source/destination address register (DMSRCx/DMDSTx) as selected by the SIND/DIND bits. • Frame index: If the transfer is the last in a frame, frame index is used for address adjustment as selected by the SIND/DIND bits. This occurs in both single-frame and multiframe transfers. 3.12.10 DMA Interrupts The ability of the DMA to interrupt the CPU based on the status of the data transfer is configurable and is determined by the IMOD and DINM bits in the DMA transfer mode control register (DMMCRn). The available modes are shown in Table 3-11. Table 3-11. DMA Interrupts MODE DINM IMOD INTERRUPT ABU (non-decrement) 1 0 At full buffer only ABU (non-decrement) 1 1 At half buffer and full buffer Multiframe 1 0 At block transfer complete (DMCTRn = DMSEFCn[7:0] = 0) Multiframe 1 1 At end of frame and end of block (DMCTRn = 0) Either 0 X No interrupt generated Either 0 X No interrupt generated 3.12.11 DMA Controller Synchronization Events The transfers associated with each DMA channel can be synchronized to one of several events. The DSYN bit field of the DMSEFCn register selects the synchronization event for a channel. The list of possible events and the DSYN values are shown in Table 3-12. Table 3-12. DMA Synchronization Events DSYN VALUE 42 DMA SYNCHRONIZATION EVENT 0000b No synchronization used 0001b McBSP0 receive event 0010b McBSP0 transmit event 0011b McBSP2 receive event 0100b McBSP2 transmit event 0101b McBSP1 receive event 0110b McBSP1 transmit event 0111b McBSP0 receive event - ABIS mode 1000b McBSP0 transmit event - ABIS mode 1001b McBSP2 receive event - ABIS mode 1010b McBSP2 transmit event - ABIS mode 1011b McBSP1 receive event - ABIS mode 1100b McBSP1 transmit event - ABIS mode 1101b Timer interrupt event Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Table 3-12. DMA Synchronization Events (continued) DSYN VALUE DMA SYNCHRONIZATION EVENT 1110b INT3 goes active 1111b Reserved The DMA controller can generate a CPU interrupt for each of the six channels. However, due to a limit on the number of internal CPU interrupt inputs, channels 0, 1, 2, and 3 are multiplexed with other interrupt sources. DMA channels 0, 1, 2, and 3 share an interrupt line with the receive and transmit portions of the McBSP. When the device is reset, the interrupts from these three DMA channels are deselected. The INTSEL bit field in the DMPREC register can be used to select these interrupts, as shown in Table 3-13. Table 3-13. DMA Channel Interrupt Selection INTSEL Value IMR/IFR[6] IMR/IFR[7] IMR/IFR[10] IMR/IFR[11] 00b (reset) BRINT2 BXINT2 BRINT1 BXINT1 01b BRINT2 BXINT2 DMAC2 DMAC3 DMAC0 DMAC1 DMAC2 DMAC3 10b 11b Reserved 3.13 General-Purpose I/O Pins In addition to the standard BIO and XF pins, the device has pins that can be configured for general-purpose I/O. These pins are: • 18 McBSP pins – BCLKX0/1/2, – BCLKR0/1/2 – BDR0/1/2 – BFSX0/1/2 – BFSR0/1/2 – BDX0/1/2 • 8 HPI data pins – HD0-HD7 The general-purpose I/O function of these pins is only available when the primary pin function is not required. 3.13.1 McBSP Pins as General-Purpose I/O When the receive or transmit portion of a McBSP is in reset, its pins can be configured as general-purpose inputs or outputs. For more details on this feature, see Section 3.8. Submit Documentation Feedback Functional Overview 43 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 3.13.2 HPI Data Pins as General-Purpose I/O The 8-bit bidirectional data bus of the HPI can be used as general-purpose input/output (GPIO) pins when the HPI is disabled (HPIENA = 0) or when the HPI is used in HPI16 mode (HPI16 = 1). Two memory-mapped registers are used to control the GPIO function of the HPI data pins—the general-purpose I/O control register (GPIOCR) and the general-purpose I/O status register (GPIOSR). The GPIOCR is shown in Figure 3-20. 15 8 Reserved 0 7 6 5 4 3 2 1 0 DIR7 DIR6 DIR5 DIR4 DIR3 DIR2 DIR1 DIR0 R/W-0 R/W-0 R/W-0 R/W-0 LEGEND: R = Read, W = Write, n = value present after reset R/W-0 R/W-0 R/W-0 R/W-0 Figure 3-20. General-Purpose I/O Control Register (GPIOCR) [MMR Address 003Ch] The direction bits (DIRx) are used to configure HD0-HD7 as inputs or outputs. The status of the GPIO pins can be monitored using the bits of the GPIOSR. The GPIOSR is shown in Figure 3-21. 15 8 Reserved 0 7 6 5 4 IO7 IO6 IO5 IO4 3 R/W-0 R/W-0 R/W-0 R/W-0 LEGEND: R = Read, W = Write, n = value present after reset 2 1 0 IO3 IO2 IO1 IO0 R/W-0 R/W-0 R/W-0 R/W-0 Figure 3-21. General-Purpose I/O Status Register (GPIOSR) [MMR Address 003Dh] 3.14 Device ID Register A read-only memory-mapped register has been added to the device to allow user application software to identify on which device the program is being executed. 15 8 CHIP ID R 7 4 3 0 CHIP REVISION SUBSYSID R LEGEND: R = Read, W = Write, n = value present after reset R Figure 3-22. Device ID Register (CSIDR) [MMR Address 003Eh] Table 3-14. Device ID Register (CSIDR) Bits BIT 44 FUNCTION 15-8 Chip ID (hex code of 16) 7-4 Chip revision ID 3-0 Subsystem ID (0000b for single core devices) Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 3.15 Memory-Mapped Registers The device has 27 memory-mapped CPU registers, which are mapped in data memory space address 0h to 1Fh. Each device also has a set of memory-mapped registers associated with peripherals. Table 3-15 gives a list of CPU memory-mapped registers (MMRs) available. Table 3-16 shows additional peripheral MMRs associated with the device. Table 3-15. CPU Memory-Mapped Registers NAME ADDRESS DESCRIPTION DEC HEX IMR 0 0 Interrupt mask register IFR 1 1 Interrupt flag register 2-5 2-5 Reserved for testing ST0 6 6 Status register 0 ST1 7 7 Status register 1 AL 8 8 Accumulator A low word (15-0) — AH 9 9 Accumulator A high word (31-16) AG 10 A Accumulator A guard bits (39-32) BL 11 B Accumulator B low word (15-0) BH 12 C Accumulator B high word (31-16) BG 13 D Accumulator B guard bits (39-32) TREG 14 E Temporary register TRN 15 F Transition register AR0 16 10 Auxiliary register 0 AR1 17 11 Auxiliary register 1 AR2 18 12 Auxiliary register 2 AR3 19 13 Auxiliary register 3 AR4 20 14 Auxiliary register 4 AR5 21 15 Auxiliary register 5 AR6 22 16 Auxiliary register 6 AR7 23 17 Auxiliary register 7 SP 24 18 Stack pointer register BK 25 19 Circular buffer size register BRC 26 1A Block repeat counter RSA 27 1B Block repeat start address REA 28 1C Block repeat end address PMST 29 1D Processor mode status (PMST) register XPC 30 1E Extended program page register — 31 1F Reserved Table 3-16. Peripheral Memory-Mapped Registers for Each DSP Subsystem NAME ADDRESS DESCRIPTION DEC HEX DRR20 32 20 McBSP 0 Data Receive Register 2 DRR10 33 21 McBSP 0 Data Receive Register 1 DXR20 34 22 McBSP 0 Data Transmit Register 2 DXR10 35 23 McBSP 0 Data Transmit Register 1 TIM 36 24 Timer Register PRD 37 25 Timer Period Register TCR 38 26 Timer Control Register Submit Documentation Feedback Functional Overview 45 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Table 3-16. Peripheral Memory-Mapped Registers for Each DSP Subsystem (continued) NAME ADDRESS DESCRIPTION DEC HEX — 39 27 Reserved SWWSR 40 28 Software Wait-State Register BSCR 41 29 Bank-Switching Control Register — 42 2A Reserved SWCR 43 2B Software Wait-State Control Register HPIC 44 2C HPI Control Register (HMODE = 0 only) 45-47 2D-2F DRR22 48 30 McBSP 2 Data Receive Register 2 DRR12 49 31 McBSP 2 Data Receive Register 1 DXR22 50 32 McBSP 2 Data Transmit Register 2 DXR12 51 33 McBSP 2 Data Transmit Register 1 SPSA2 52 34 McBSP 2 Subbank Address Register (1) SPSD2 53 35 McBSP 2 Subbank Data Register (1) 54-55 36-37 SPSA0 56 38 McBSP 0 Subbank Address Register (1) SPSD0 57 39 McBSP 0 Subbank Data Register (1) — — — Reserved Reserved 58-59 3A-3B GPIOCR 60 3C General-Purpose I/O Control Register GPIOSR 61 3D General-Purpose I/O Status Register CSIDR 62 3E Device ID Register — 63 3F Reserved DRR21 64 40 McBSP 1 Data Receive Register 2 DRR11 65 41 McBSP 1 Data Receive Register 1 DXR21 66 42 McBSP 1 Data Transmit Register 2 McBSP 1 Data Transmit Register 1 DXR11 Reserved 67 43 68-71 44-47 SPSA1 72 48 McBSP 1 Subbank Address Register (1) SPSD1 73 49 McBSP 1 Subbank Data Register (1) — — Reserved 74-83 4A-53 DMPREC 84 54 DMA Priority and Enable Control Register DMSA 85 55 DMA Subbank Address Register (2) DMSDI 86 56 DMA Subbank Data Register with Autoincrement (2) DMSDN 87 57 DMA Subbank Data Register (2) CLKMD 88 58 Clock Mode Register (CLKMD) 89-95 59-5F — (1) (2) 46 Reserved Reserved See Table 3-17 for a detailed description of the McBSP control registers and their subaddresses. See Table 3-18 for a detailed description of the DMA subbank addressed registers. Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 3.16 McBSP Control Registers and Subaddresses The control registers for the multichannel buffered serial port (McBSP) are accessed using the subbank addressing scheme. This allows a set or subbank of registers to be accessed through a single memory location. The McBSP subbank address register (SPSA) is used as a pointer to select a particular register within the subbank. The McBSP data register (SPSDx) is used to access (read or write) the selected register. Table 3-17 shows the McBSP control registers and their corresponding subaddresses. Table 3-17. McBSP Control Registers and Subaddresses McBSP0 McBSP1 McBSP2 NAME ADDRESS NAME ADDRESS NAME ADDRESS SUBADDRESS SPCR10 39h SPCR11 49h SPCR12 35h 00h Serial port control register 1 SPCR20 39h SPCR21 49h SPCR22 35h 01h Serial port control register 2 RCR10 39h RCR11 49h RCR12 35h 02h Receive control register 1 RCR20 39h RCR21 49h RCR22 35h 03h Receive control register 2 XCR10 39h XCR11 49h XCR12 35h 04h Transmit control register 1 XCR20 39h XCR21 49h XCR22 35h 05h Transmit control register 2 SRGR10 39h SRGR11 49h SRGR12 35h 06h Sample rate generator register 1 SRGR20 39h SRGR21 49h SRGR22 35h 07h Sample rate generator register 2 MCR10 39h MCR11 49h MCR12 35h 08h Multichannel control register 1 DESCRIPTION MCR20 39h MCR21 49h MCR22 35h 09h Multichannel control register 2 RCERA0 39h RCERA1 49h RCERA2 35h 0Ah Receive channel enable register partition A RCERB0 39h RCERB1 49h RCERA2 35h 0Bh Receive channel enable register partition B XCERA0 39h XCERA1 49h XCERA2 35h 0Ch Transmit channel enable register partition A XCERB0 39h XCERB1 49h XCERA2 35h 0Dh Transmit channel enable register partition B PCR0 39h PCR1 49h PCR2 35h 0Eh Pin control register RCERC0 39h RCERC1 49h RCERC2 35h 010h Additional channel enable register for 128-channel selection RCERD0 39h RCERD1 49h RCERD2 35h 011h Additional channel enable register for 128-channel selection XCERC0 39h XCERC1 49h XCERC2 35h 012h Additional channel enable register for 128-channel selection XCERD0 39h XCERD1 49h XCERD2 35h 013h Additional channel enable register for 128-channel selection RCERE0 39h RCERE1 49h RCERE2 35h 014h Additional channel enable register for 128-channel selection RCERF0 39h RCERF1 49h RCERF2 35h 015h Additional channel enable register for 128-channel selection XCERE0 39h XCERE1 49h XCERE2 35h 016h Additional channel enable register for 128-channel selection XCERF0 39h XCERF1 49h XCERF2 35h 017h Additional channel enable register for 128-channel selection RCERG0 39h RCERG1 49h RCERG2 35h 018h Additional channel enable register for 128-channel selection RCERH0 39h RCERH1 49h RCERH2 35h 019h Additional channel enable register for 128-channel selection XCERG0 39h XCERG1 49h XCERG2 35h 01Ah Additional channel enable register for 128-channel selection XCERH0 39h XCERH1 49h XCERH2 35h 01Bh Additional channel enable register for 128-channel selection Submit Documentation Feedback Functional Overview 47 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 3.17 DMA Subbank Addressed Registers The direct memory access (DMA) controller has several control registers associated with it. The main control register (DMPREC) is a standard memory-mapped register. However, the other registers are accessed using the subbank addressing scheme. This allows a set or subbank of registers to be accessed through a single memory location. The DMA subbank address (DMSA) register is used as a pointer to select a particular register within the subbank, while the DMA subbank data (DMSD) register or the DMA subbank data register with autoincrement (DMSDI) is used to access (read or write) the selected register. When the DMSDI register is used to access the subbank, the subbank address is automatically postincremented so that a subsequent access affects the next register within the subbank. This autoincrement feature is intended for efficient, successive accesses to several control registers. If the autoincrement feature is not required, the DMSDN register should be used to access the subbank. Table 3-18 shows the DMA controller subbank addressed registers and their corresponding subaddresses. Table 3-18. DMA Subbank Addressed Registers ADDRESS SUBADDRESS DMSRC0 56h/57h 00h DMA channel 0 source address register DMDST0 56h/57h 01h DMA channel 0 destination address register DMCTR0 56h/57h 02h DMA channel 0 element count register DMSFC0 56h/57h 03h DMA channel 0 sync select and frame count register DMMCR0 56h/57h 04h DMA channel 0 transfer mode control register DMSRC1 56h/57h 05h DMA channel 1 source address register DMDST1 56h/57h 06h DMA channel 1 destination address register DMCTR1 56h/57h 07h DMA channel 1 element count register DMSFC1 56h/57h 08h DMA channel 1 sync select and frame count register DMMCR1 56h/57h 09h DMA channel 1 transfer mode control register DMSRC2 56h/57h 0Ah DMA channel 2 source address register DMDST2 56h/57h 0Bh DMA channel 2 destination address register DMCTR2 56h/57h 0Ch DMA channel 2 element count register DMSFC2 56h/57h 0Dh DMA channel 2 sync select and frame count register DMMCR2 56h/57h 0Eh DMA channel 2 transfer mode control register DMSRC3 56h/57h 0Fh DMA channel 3 source address register DMDST3 56h/57h 10h DMA channel 3 destination address register DMCTR3 56h/57h 11h DMA channel 3 element count register DMSFC3 56h/57h 12h DMA channel 3 sync select and frame count register DMMCR3 56h/57h 13h DMA channel 3 transfer mode control register DMSRC4 56h/57h 14h DMA channel 4 source address register DMDST4 56h/57h 15h DMA channel 4 destination address register DMCTR4 56h/57h 16h DMA channel 4 element count register DMSFC4 56h/57h 17h DMA channel 4 sync select and frame count register DMMCR4 56h/57h 18h DMA channel 4 transfer mode control register DMSRC5 56h/57h 19h DMA channel 5 source address register DMDST5 56h/57h 1Ah DMA channel 5 destination address register DMCTR5 56h/57h 1Bh DMA channel 5 element count register DMSFC5 56h/57h 1Ch DMA channel 5 sync select and frame count register DMMCR5 56h/57h 1Dh DMA channel 5 transfer mode control register DMSRCP 56h/57h 1Eh DMA source program page address (common channel) DMDSTP 56h/57h 1Fh DMA destination program page address (common channel) DMIDX0 56h/57h 20h DMA element index address register 0 DMIDX1 56h/57h 21h DMA element index address register 1 NAME 48 Functional Overview DESCRIPTION Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Table 3-18. DMA Subbank Addressed Registers (continued) ADDRESS SUBADDRESS DMFRI0 56h/57h 22h DMA frame index register 0 DMFRI1 56h/57h 23h DMA frame index register 1 DMGSA0 56h/57h 24h DMA global source address reload register, channel 0 DMGDA0 56h/57h 25h DMA global destination address reload register, channel 0 DMGCR0 56h/57h 26h DMA global count reload register, channel 0 DMGFR0 56h/57h 27h DMA global frame count reload register, channel 0 XSRCDP 56h/57h 28h DMA extended source data page (currently not supported) XDSTDP 56h/57h 29h DMA extended destination data page (currently not supported) DMGSA1 56h/57h 2Ah DMA global source address reload register, channel 1 DMGDA1 56h/57h 2Bh DMA global destination address reload register, channel 1 DMGCR1 56h/57h 2Ch DMA global count reload register, channel 1 DMGFR1 56h/57h 2Dh DMA global frame count reload register, channel 1 DMGSA2 56h/57h 2Eh DMA global source address reload register, channel 2 DMGDA2 56h/57h 2Fh DMA global destination address reload register, channel 2 DMGCR2 56h/57h 30h DMA global count reload register, channel 2 DMGFR2 56h/57h 31h DMA global frame count reload register, channel 2 DMGSA3 56h/57h 32h DMA global source address reload register, channel 3 DMGDA3 56h/57h 33h DMA global destination address reload register, channel 3 DMGCR3 56h/57h 34h DMA global count reload register, channel 3 DMGFR3 56h/57h 35h DMA global frame count reload register, channel 3 DMGSA4 56h/57h 36h DMA global source address reload register, channel 4 DMGDA4 56h/57h 37h DMA global destination address reload register, channel 4 DMGCR4 56h/57h 38h DMA global count reload register, channel 4 DMGFR4 56h/57h 39h DMA global frame count reload register, channel 4 DMGSA5 56h/57h 3Ah DMA global source address reload register, channel 5 DMGDA5 56h/57h 3Bh DMA global destination address reload register, channel 5 DMGCR5 56h/57h 3Ch DMA global count reload register, channel 5 DMGFR5 56h/57h 3Dh DMA global frame count reload register, channel 5 NAME Submit Documentation Feedback DESCRIPTION Functional Overview 49 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 3.18 Interrupts Vector-relative locations and priorities for all internal and external interrupts are shown in Table 3-19. Table 3-19. Interrupt Locations and Priorities TRAP/INTR NUMBER (K) NAME LOCATION DECIMAL HEX PRIORITY FUNCTION RS, SINTR 0 0 00 1 Reset (hardware and software reset) NMI, SINT16 1 4 04 2 Nonmaskable interrupt SINT17 2 8 08 — Software interrupt #17 SINT18 3 12 0C — Software interrupt #18 SINT19 4 16 10 — Software interrupt #19 SINT20 5 20 14 — Software interrupt #20 SINT21 6 24 18 — Software interrupt #21 SINT22 7 28 1C — Software interrupt #22 SINT23 8 32 20 — Software interrupt #23 SINT24 9 36 24 — Software interrupt #24 SINT25 10 40 28 — Software interrupt #25 SINT26 11 44 2C — Software interrupt #26 SINT27 12 48 30 — Software interrupt #27 SINT28 13 52 34 — Software interrupt #28 SINT29 14 56 38 — Software interrupt #29 SINT30 15 60 3C — Software interrupt #30 INT0, SINT0 16 64 40 3 External user interrupt #0 INT1, SINT1 17 68 44 4 External user interrupt #1 INT2, SINT2 18 72 48 5 External user interrupt #2 TINT, SINT3 19 76 4C 6 Timer interrupt RINT0, SINT4 20 80 50 7 McBSP #0 receive interrupt (default) XINT0, SINT5 21 84 54 8 McBSP #0 transmit interrupt (default) RINT2, SINT6 22 88 58 9 McBSP #2 receive interrupt (default) XINT2, SINT7 23 92 5C 10 McBSP #2 transmit interrupt (default) INT3, SINT8 24 96 60 11 External user interrupt #3 HINT, SINT9 25 100 64 12 HPI interrupt RINT1, SINT10 26 104 68 13 McBSP #1 receive interrupt (default) XINT1, SINT11 27 108 6C 14 McBSP #1 transmit interrupt (default) DMAC4,SINT12 28 112 70 15 DMA channel 4 (default) DMAC5,SINT13 Reserved 29 116 74 16 DMA channel 5 (default) 30-31 120-127 78-7F — Reserved The bit layout of the interrupt flag register (IFR) and the interrupt mask register (IMR) is shown in Figure 3-23. 15 14 Reserved 13 12 11 10 DMAC5 DMAC4 XINT1 RINT1 9 HINT 8 INT3 7 6 5 4 3 2 1 0 XINT2 RINT2 XINT0 RINT0 TINT INT2 INT1 INT0 LEGEND: R = Read, W = Write, n = value present after reset Figure 3-23. IFR and IMR Registers 50 Functional Overview Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 4 Support 4.1 Documentation Support Extensive documentation supports all TMS320™ DSP family of devices from product announcement through applications development. The following types of documentation are available to support the design and use of the C5000™ platform of DSPs: SPRU307: TMS320C54x DSP Family Functional Overview Provides a functional overview of the devices included in the TMS320C54x™ DSP generation of digital signal processors. Included are descriptions of the CPU architecture, bus structure, memory structure, on-chip peripherals, and instruction set. SPRA164: Calculation of TMS320LC54x Power Dissipation Describes the power-saving features of the TMS320LC54x and presents techniques for analyzing systems and device conditions to determine operating current levels and power dissipaton. From this information, informed decisions can be made regarding power supply requirements and thermal management considerations. The five-volume TMS320C54x DSP Reference Set consists of: SPRU131: TMS320C54x DSP Reference Set, Volume 1: CPU Describes the TMS320C54x 16-bit fixed-point general-purpose digital signal processors. Covered are its architecture, internal register structure, data and program addressing, and the instruction pipeline. Also includes development support information, parts lists, and design considerations for using the XDS510 emulator. SPRU172: TMS320C54x DSP Reference Set, Volume 2: Mnemonic Instruction Set Describes the TMS320C54x digital signal processor mnemonic instructions individually. Also includes a summary of instruction set classes and cycles. SPRU179: TMS320C54x DSP Reference Set, Volume 3: Algebraic Instruction Set Describes the TMS320C54x digital signal processor algebraic instructions individually. Also includes a summary of instruction set classes and cycles. SPRU173: TMS320C54x DSP Reference Set, Volume 4: Applications Guide Describes software and hardware applications for the TMS320C54x digital signal processor. Also includes development support information, parts lists, and design considerations for using the XDS510 emulator. SPRU302: TMS320C54x DSP Reference Set, Volume 5: Enhanced Peripherals Describes the enhanced peripherals available on the TMS320C54x digital signal processors. Includes the multichannel buffered serial ports (McBSPs), direct memory access (DMA) controller, interprocessor communications, and the HPI-8 and HPI-16 host port interfaces. The reference set describes in detail the TMS320C54x™ DSP products currently available and the hardware and software applications, including algorithms, for fixed-point TMS320™ DSP family of devices. A series of DSP textbooks is published by Prentice-Hall and John Wiley & Sons to support digital signal processing research and education. The TMS320 DSP newsletter, Details on Signal Processing, is published quarterly and distributed to update TMS320 DSP customers on product information. Information regarding TI DSP porducts is also available on the web at www.ti.com. Submit Documentation Feedback Support 51 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 4.2 www.ti.com Device and Development-Support Tool Nomenclature To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all TMS320 DSP devices and support tools. Each TMS320 DSP commercial family member has one of three prefixes: TMX, TMP, or TMS (e.g., TMS320C6412GDK600). Texas Instruments recommends two of three possible prefix designators for its support tools: TMDX and TMDS. These prefixes represent evolutionary stages of product development from engineering prototypes (TMX/TMDX) through fully qualified production devices/tools (TMS/TMDS). Device development evolutionary flow: TMX Experimental device that is not necessarily representative of the final device's electrical specifications TMP Final silicon die that conforms to the device's electrical specifications but has not completed quality and reliability verification TMS Fully qualified production device Support tool development evolutionary flow: TMDX Development-support product that has not yet completed Texas Instruments internal qualification testing. TMDS Fully qualified development-support product TMX and TMP devices and TMDX development-support tools are shipped with appropriate disclaimers describing their limitations and intended uses. "Developmental product is intended for internal evaluation purposes." TMS devices and TMDS development-support tools have been characterized fully, and the quality and reliability of the device have been demonstrated fully. TI's standard warranty applies. Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard production devices. Texas Instruments recommends that these devices not be used in any production system because their expected end-use failure rate still is undefined. Only qualified production devices are to be used. 52 Support Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 5 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Electrical Specifications This section provides the absolute maximum ratings and the recommended operating conditions for the TMS320VC5416 DSP. 5.1 Absolute Maximum Ratings The absolute maximum ratings are measure over operating case temperature range. Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Section 5.3.1 is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to DVSS. DVDD Supply voltage I/O range – 0.3 V to 4.0 V CVDD Supply voltage core range – 0.3 V to 2.0 V VI Input voltage range – 0.3 V to 4.5 V VO Output voltage range – 0.3 V to 4.5 V TC Operating case temperature range – 40°C to 100°C Tstg Storage temperature range – 55°C to 150°C 5.2 Recommended Operating Conditions MIN NOM MAX 2.7 3.3 3.6 V Device supply voltage, core (VC5416-160) 1.55 1.6 1.65 V Device supply voltage, core (VC5416-120) 1.42 1.5 1.65 V DVDD Device supply voltage, I/O CVDD CVDD DVSS CVSS Supply voltage, GND 0 VIH High-level input voltage, I/O VIL Low-level input voltage RS, INTn, NMI, X2/CLKIN, CLKMDn, BCLKRn, BCLKXn, HCS, HDS1, HDS2, HAS, TRST, BIO, Dn, An, HDn, TCK DVDD = 2.7 V to 3.6 V All other inputs UNIT V 2.4 DVDD + 0.3 2 DVDD + 0.3 – 0.3 V 0.8 V IOH High-level output current (1) (2) –8 mA IOL Low-level output current (1) (2) 8 mA TC Operating case temperature 100 °C (1) (2) – 40 The maximum output currents are DC values only. Transient currents may exceed these values. These output current limits are used for the test conditions on VOL and VOH, except where noted otherwise. Submit Documentation Feedback Electrical Specifications 53 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.3 www.ti.com Electrical Characteristics The electrical charactheristics are measured over recommended operating case temperature range (unless otherwise noted). All values are typical unless otherwise specified. PARAMETER VOH High-level output voltage (1) VOL Low-level output voltage (1) TEST CONDITIONS MIN DVDD = 2.7 V to 3 V, IOH = – 2 mA 2.2 DVDD = 3 V to 3.6 V, IOH = MAX 2.4 Input current (VI = DVSS to DVDD) MAX 0.4 V – 40 40 µA TRST, HPI16 With internal pulldown – 10 800 HPIENA With internal pulldown, RS = 0 – 10 400 – 400 10 – 275 275 TMS, TCK, TDI, HPI (2) A[17:0], D[15:0], HD[7:0] With internal pullups Bus holders enabled, DVDD = MAX (3) All other input-only pins UNIT V IOL = MAX X2/CLKIN II TYP –5 µA 5 IDDC Supply current, core CPU CVDD = 1.6 V, fx = 160 , (4)TC = 25°C 60 (5) mA IDDP Supply current, pins DVDD = 3.0 V, fx = 160 MHz, (4)TC = 25°C 40 (6) mA IDD Supply current, standby Ci Co (1) (2) (3) (4) (5) (6) IDLE2 PLL × 1 mode, 20 MHz input IDLE3 Divide-by-two mode, CLKIN stopped TC = 25°C 1 TC = 100°C 30 2 mA Input capacitance 5 pF Output capacitance 5 pF All input and output voltage levels except RS, INT0-INT3, NMI, X2/CLKIN, CLKMD1-CLKMD3, BCLKRn, BCLKXn, HCS, HAS, HDS1, HDS2, BIO, TCK, TRST, Dn, An, HDn are LVTTL-compatible. HPI input signals except for HPIENA and HPI16, when HPIENA = 0. VIL(MIN) ≤ VI ≤ VIL(MAX) or VIH(MIN) ≤ VI ≤ VIH(MAX) Clock mode: PLL × 1 with external source This value was obtained with 50% usage of MAC and 50% usage of NOP instructions. Actual operating current varies with program being executed. This value was obtained with single-cycle external writes, CLKOFF = 0 and load = 15 pF. For more details on how this calculation is performed, refer to the Calculation of TMS320LC54x Power Dissipation application report (literature number SPRA164). 5.3.1 Test Loading Tester Pin Electronics 42 W 3.5 nH Transmission Line Z0 = 50 W (see note) 4.0 pF 1.85 pF Data Sheet Timing Reference Point Output Under Test Device Pin (see note) NOTE: The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its transmission line effects must taken into account. A transmission line with a delay of 2 ns or longer can be used to produce the desired transmission line effect. The transmission line is intended as a load only. It is not necessary to add or subtract the transmission line delay (2 ns or longer) from the data sheet timings. Input requirements in this data sheet are tested with an input slew rate of < 4 Volts per nanosecond (4 V/ns) at the device pin. Figure 5-1. Tester Pin Electronics 54 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.3.2 Timing Parameter Symbology Timing parameter symbols used in the timing requirements and switching characteristics tables are created in accordance with JEDEC Standard 100. To shorten the symbols, some of the pin names and other related terminology have been abbreviated as follows: Lowercase subscripts and their meanings: Letters and symbols and their meanings: a access time H High c cycle time (period) L Low d delay time V Valid dis disable time Z High impedance en enable time f fall time h hold time r rise time su setup time t transition time v valid time w pulse duration (width) X Unknown, changing, or don't care level Submit Documentation Feedback Electrical Specifications 55 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 5.3.3 Internal Oscillator With External Crystal The internal oscillator is enabled by selecting the appropriate clock mode at reset (this is device-dependent; see Section 3.10) and connecting a crystal or ceramic resonator across X1 and X2/CLKIN. The CPU clock frequency is one-half, one-fourth, or a multiple of the oscillator frequency. The multiply ratio is determined by the bit settings in the CLKMD register. The crystal should be in fundamental-mode operation, and parallel resonant, with an effective series resistance of 30Ω maximum and power dissipation of 1 mW. The connection of the required circuit, consisting of the crystal and two load capacitors, is shown in Figure 5-2. The load capacitors, C1 and C2, should be chosen such that the equation below is satisfied. CL (recommended value of 10 pF) in the equation is the load specified for the crystal. CL + C 1C 2 (C1 ) C2) Table 5-1. Input Clock Frequency Characteristics fx (1) (2) Input clock frequency MIN MAX Unit 10 (1) 20 (2) MHz This device utilizes a fully static design and therefore can operate with tc(CI) approaching ∞. The device is characterized at frequencies approaching 0 Hz It is recommended that the PLL multiply by N clocking option be used for maximum frequency operation. X1 X2/CLKIN Crystal C1 C2 Figure 5-2. Internal Divide-By-Two Clock Option With External Crystal 56 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 5.4 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Clock Options The frequency of the reference clock provided at the CLKIN pin can be divided by a factor of two or four or multiplied by one of several values to generate the internal machine cycle. 5.4.1 Divide-By-Two and Divide-By-Four Clock Options The frequency of the reference clock provided at the X2/CLKIN pin can be divided by a factor of two or four to generate the internal machine cycle. The selection of the clock mode is described in Section 3.10. When an external clock source is used, the frequency injected must conform to specifications listed in Table 5-3. An external frequency source can be used by applying an input clock to X2/CLKIN with X1 left unconnected. Table 5-2 shows the configuration options for the CLKMD pins that generate the external divide-by-2 or divide-by-4 clock option. Table 5-3 and Table 5-4 assume testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5-3). Table 5-2. Clock Mode Pin Settings for the Divide-By-2 and By Divide-By-4 Clock Options CLKMD1 CLKMD2 CLKMD3 Clock Mode 0 0 0 1/2, PLL disabled 1 0 1 1/4, PLL disabled 1 1 1 1/2, PLL disabled Table 5-3. Divide-By-2 and Divide-By-4 Clock Options Timing Requirements 5416-120 5416-160 MIN Unit MAX tc(CI) Cycle time, X2/CLKIN tf(CI) Fall time, X2/CLKIN 20 4 ns ns tr(CI) Rise time, X2/CLKIN 4 ns tw(CIL) Pulse duration, X2/CLKIN low 4 ns tw(CIH) Pulse duration, X2/CLKIN high 4 ns Table 5-4. Divide-By-2 and Divide-By-4 Clock Options Switching Characteristics PARAMETER 5416-120 MIN TYP 8.33 (1) 5416-160 MAX (2) MIN TYP 6.25 (1) MAX Unit (2) ns 11 ns tc(CO) Cycle time, CLKOUT td(CIH-CO) Delay time, X2/CLKIN high to CLKOUT high/low tf(CO) Fall time, CLKOUT 1 1 ns tr(CO) Rise time, CLKOUT 1 1 ns tw(COL) Pulse duration, CLKOUT low H–2 H H+1 H–2 H H+1 ns tw(COH) Pulse duration, CLKOUT high H–2 H H+1 H–2 H H+1 ns (1) (2) 4 7 11 4 7 It is recommended that the PLL clocking operation be used for maximum frequency operation. This device utilizes a fully static design and therefore can operate with tc(Cl) approaching ∞. The device is characterized at frequencies approaching 0 Hz. Submit Documentation Feedback Electrical Specifications 57 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com tr(CI) tw(CIH) tf(CI) tw(CIL) tc(CI) X2/CLKIN tc(CO) td(CIH-CO) tw(COH) tf(CO) tr(CO) tw(COL) CLKOUT (see Note A) A. The CLKOUT timing in this diagram assumes the CLKOUT divide factor (DIVFCT field in the BSCR) is configured as 00 (CLKOUT not divided). DIVFCT is configured as CLKOUT divided-by-4 mode following reset. Figure 5-3. External Divide-By-Two Clock Timing 58 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 5.4.2 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Multiply-By-N Clock Option (PLL Enabled) The frequency of the reference clock provided at the X2/CLKIN pin can be multiplied by a factor of N to generate the internal machine cycle. The selection of the clock mode and the value of N is described in Section 3.10. Following reset, the software PLL can be programmed for the desired multiplication factor. Refer to the TMS320C54x DSP Reference Set, Volume 1: CPU and Peripherals (literature number SPRU131) for detailed information on programming the PLL. When an external clock source is used, the external frequency injected must conform to specifications listed in Table 5-5. Table 5-5 and Table 5-6 assume testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5-4). Table 5-5. Multiply-By-N Clock Option Timing Requirements 5416-120 5416-160 tc(CI) Cycle time, X2/CLKIN Unit MIN MAX Integer PLL multiplier N (N = 1-15) (1) 20 200 PLL multiplier N = x.5 (1) 20 100 20 50 PLL multiplier N = x.25, x.75 (1) ns tf(CI) Fall time, X2/CLKIN 4 ns tr(CI) Rise time, X2/CLKIN 4 ns tw(CIL) Pulse duration, X2/CLKIN low 4 ns tw(CIH) Pulse duration, X2/CLKIN high 4 ns (1) N is the multiplication factor. Table 5-6. Multiply-By-N Clock Option Switching Characteristics 5416-120 PARAMETER MIN 5416-160 TYP MAX 7 11 8.33 MIN TYP MAX 7 11 tc(CO) Cycle time, CLKOUT td(CI-CO) Delay time, X2/CLKIN high/low to CLKOUT high/low tf(CO) Fall time, CLKOUT 2 2 tr(CO) Rise time, CLKOUT 2 2 tw(COL) Pulse duration, CLKOUT low H–2 H H+1 H–2 H H+1 tw(COH) Pulse duration, CLKOUT high H–2 H H+1 H–2 H H+1 ns tp Transitory phase, PLL lock-up time 30 ms 4 6.25 Unit ns 4 30 tw(CIH) tc(CI) tw(CIL) ns ns ns ns tf(CI) tr(CI) X2/CLKIN td(CI-CO) tw(COH) tc(CO) tp CLKOUT (see Note A) A. tf(CO) tw(COL) tr(CO) Unstable The CLKOUT timing in this diagram assumes the CLKOUT divide factor (DIVFCT field in the BSCR) is configured as 00 (CLKOUT not divided). DIVFCT is configured as CLKOUT divided-by-4 mode following reset. Figure 5-4. Multiply-By-One Clock Timing Submit Documentation Feedback Electrical Specifications 59 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.5 www.ti.com Memory and Parallel I/O Interface Timing 5.5.1 Memory Read External memory reads can be performed in consecutive or nonconsecutive mode under control of the CONSEC bit in the BSCR. Table 5-7 and Table 5-8 assume testing over recommended operating conditions with MSTRB = 0 and H = 0.5tc(CO) (see Figure 5-5 and Figure 5-6). Table 5-7. Memory Read Timing Requirements 5416-120 5416-160 MIN UNIT MAX ta(A)M1 Access time, read data access from address valid, first read access (1) 4H–9 ns ta(A)M2 Access time, read data access from address valid, consecutive read accesses (1) 2H–9 ns tsu(D)R Setup time, read data valid before CLKOUT low 7 ns th(D)R Hold time, read data valid after CLKOUT low 0 ns (1) Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. Table 5-8. Memory Read Switching Characteristics PARAMETER 5416-120 5416-160 UNIT MIN MAX td(CLKL-A) Delay time, CLKOUT low to address valid (1) –1 4 ns td(CLKL-MSL) Delay time, CLKOUT low to MSTRB low –1 4 ns td(CLKL-MSH) Delay time, CLKOUT low to MSTRB high 0 4 ns (1) 60 Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 CLKOUT td(CLKL-A) A[22:0] (see Note A) td(CLKL-MSL) td(CLKL-MSH) ta(A)M1 D[15:0] tsu(D)R th(D)R MSTRB R/W (see Note A) PS/DS (see Note A) A. Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. Figure 5-5. Nonconsecutive Mode Memory Reads Submit Documentation Feedback Electrical Specifications 61 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com CLKOUT td(CLKL-A) td(CLKL-MSL) td(CLKL-A) td(CLKL-A) A[22:0] (see Note A) td(CLKL-MSH) ta(A)M1 ta(A)M2 D[15:0] tsu(D)R tsu(D)R th(D)R th(D)R MSTRB R/W (see Note A) PS/DS (see Note A) A. Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. Figure 5-6. Consecutive Mode Memory Reads 62 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 5.5.2 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Memory Write Table 5-9 assumes testing over recommended operating conditions with MSTRB = 0 and H = 0.5tc(CO) (see Figure 5-7). Table 5-9. Memory Write Switching Characteristics 5416-120 5416-160 PARAMETER UNIT MIN MAX –1 4 td(CLKL-A) Delay time, CLKOUT low to address valid (1) tsu(A)MSL Setup time, address valid before MSTRB low (1) td(CLKL-D)W Delay time, CLKOUT low to data valid –1 4 ns tsu(D)MSH Setup time, data valid before MSTRB high 2H – 4 2H + 6 ns th(D)MSH Hold time, data valid after MSTRB high 2H – 5 2H + 6 ns td(CLKL-MSL) Delay time, CLKOUT low to MSTRB low –1 4 ns tw(SL)MS Pulse duration, MSTRB low td(CLKL-MSH) Delay time, CLKOUT low to MSTRB high (1) 2H – 3 ns 2H – 2 0 ns ns 4 ns Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. CLKOUT td(CLKL-A) td(CLKL-A) td(CLKL-D)W tsu(A)MSL A[22:0] (see Note A) tsu(D)MSH th(D)MSH D[15:0] td(CLKL-MSL) td(CLKL-MSH) tw(SL)MS MSTRB R/W (see Note A) PS/DS (see Note A) A. Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. Figure 5-7. Memory Write (MSTRB = 0) Submit Documentation Feedback Electrical Specifications 63 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.5.3 www.ti.com I/O Read Table 5-10 and Table 5-11 assume testing over recommended operating conditions, IOSTRB = 0, and H = 0.5tc(CO) (see Figure 5-8). Table 5-10. I/O Read Timing Requirements 5416-120 5416-160 MIN UNIT MAX ta(A)M1 Access time, read data access from address valid, first read access (1) tsu(D)R Setup time, read data valid before CLKOUT low 7 ns th(D)R Hold time, read data valid after CLKOUT low 0 ns (1) 4H – 9 ns Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. Table 5-11. I/O Read Switching Characteristics 5416-120 5416-160 PARAMETER UNIT MIN MAX td(CLKL-A) Delay time, CLKOUT low to address valid (1) –1 4 ns td(CLKL-IOSL) Delay time, CLKOUT low to IOSTRB low –1 4 ns td(CLKL-IOSH) Delay time, CLKOUT low to IOSTRB high 0 4 ns (1) Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. CLKOUT td(CLKL-A) td(CLKL-A) td(CLKL-IOSL) td(CLKL-IOSH) A[22:0] (see Note A) ta(A)M1 tsu(D)R th(D)R D[15:0] IOSTRB R/W (see Note A) IS (see Note A) A. Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. Figure 5-8. Parallel I/O Port Read (IOSTRB = 0) 64 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 5.5.4 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 I/O Write Table 5-12 assumes testing over recommended operating conditions, IOSTRB = 0, and H = 0.5tc(CO) (see Figure 5-9). Table 5-12. I/O Write Switching Characteristics 5416-120 5416-160 PARAMETER UNIT MIN MAX –1 4 td(CLKL-A) Delay time, CLKOUT low to address valid (1) tsu(A)IOSL Setup time, address valid before IOSTRB low (1) td(CLKL-D)W Delay time, CLKOUT low to write data valid –1 4 ns tsu(D)IOSH Setup time, data valid before IOSTRB high 2H – 4 2H + 6 ns th(D)IOSH Hold time, data valid after IOSTRB high 2H – 5 2H + 6 ns td(CLKL-IOSL) Delay time, CLKOUT low to IOSTRB low –1 4 ns tw(SL)IOS Pulse duration, IOSTRB low td(CLKL-IOSH) Delay time, CLKOUT low to IOSTRB high (1) 2H – 3 ns ns 2H – 2 0 ns 4 ns Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. CLKOUT td(CLKL-A) td(CLKL-A) A[22:0] (see Note A) td(CLKL-D)W td(CLKL-D)W tsu(A)IOSL D[15:0] tsu(D)IOSH td(CLKL-IOSH) td(CLKL-IOSL) th(D)IOSH IOSTRB R/W (see Note A) tw(SL)IOS IS (see Note A) A. Address, R/W, PS, DS, and IS timings are all included in timings referenced as address. Figure 5-9. Parallel I/O Port Write (IOSTRB = 0) Submit Documentation Feedback Electrical Specifications 65 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 5.5.5 Ready Timing for Externally Generated Wait States Table 5-13 and Table 5-14 assume testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5-10, Figure 5-11, Figure 5-12, and Figure 5-13). Table 5-13. Ready Timing Requirements for Externally Generated Wait States (1) 5416-120 5416-160 MIN UNIT MAX tsu(RDY) Setup time, READY before CLKOUT low 7 ns th(RDY) Hold time, READY after CLKOUT low 0 ns (2) tv(RDY)MSTRB Valid time, READY after MSTRB low th(RDY)MSTRB Hold time, READY after MSTRB low (2) tv(RDY)IOSTRB Valid time, READY after IOSTRB low (2) th(RDY)IOSTRB (2) (1) (2) Hold time, READY after IOSTRB low 4H – 4 4H ns ns 4H – 4 4H ns ns The hardware wait states can be used only in conjunction with the software wait states to extend the bus cycles. To generate wait states by READY, as least two software wait states must be programmed. READY is not sampled until the completion of the internal software wait states. These timings are included for reference only. The critical timings for READY are those referenced to CLKOUT. Table 5-14. Ready Switching Characteristics for Externally Generated Wait States (1) PARAMETER 5416-120 5416-160 UNIT MIN MAX td(MSCL) Delay time, CLKOUT low to MSC low 0 4 ns td(MSCH) Delay time, CLKOUT low to MSC high 0 4 ns (1) 66 The hardware wait states can be used only in conjunction with the software wait states to extend the bus cycles. To generate wait states by READY, as least two software wait states must be programmed. READY is not sampled until the completion of the internal software wait states. Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 CLKOUT A[22:0] D[15:0] tsu(RDY) th(RDY) READY tv(RDY)MSTRB th(RDY)MSTRB MSTRB td(MSCL) td(MSCH) MSC Leading Cycle Wait States Generated Internally Wait States Generated by READY Trailing Cycle Figure 5-10. Memory Read With Externally Generated Wait States Submit Documentation Feedback Electrical Specifications 67 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com CLKOUT A[22:0] D[15:0] tsu(RDY) th(RDY) READY tv(RDY)MSTRB th(RDY)MSTRB MSTRB td(MSCL) td(MSCH) MSC Leading Cycle Wait States Generated Internally Wait States Generated by READY Trailing Cycle Figure 5-11. Memory Write With Externally Generated Wait States 68 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 CLKOUT A[22:0] D[15:0] tsu(RDY) th(RDY) READY tv(RDY)IOSTRB th(RDY)IOSTRB IOSTRB td(MSCL) td(MSCH) MSC Leading Cycle Wait States Generated Internally Wait States Generated by READY Trailing Cycle Figure 5-12. I/O Read With Externally Generated Wait States Submit Documentation Feedback Electrical Specifications 69 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com CLKOUT A[22:0] D[15:0] tsu(RDY) th(RDY) READY tv(RDY)IOSTRB th(RDY)IOSTRB IOSTRB td(MSCL) td(MSCH) MSC Leading Cycle Wait States Generated Internally Trailing Cycle Wait States Generated by READY Figure 5-13. I/O Write With Externally Generated Wait States 70 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.5.6 HOLD and HOLDA Timings Table 5-15 and Table 5-16 assume testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5-14). Table 5-15. HOLD and HOLDA Timing Requirements 5416-120 5416-160 MIN tw(HOLD) Pulse duration, HOLD low duration tsu(HOLD) Setup time, HOLD before CLKOUT low (1) (1) UNIT MAX 4H+8 ns 7 ns This input can be driven from an asynchronous source, therefore, there are no specific timing requirments with respect to CLKOUT. However, if this timing is met, the input will be recognized on the CLKOUT edge referenced. Table 5-16. HOLD and HOLDA Switching Characteristics PARAMETER 5416-120 5416-160 MIN UNIT MAX tdis(CLKL-A) Disable time, Address, PS, DS, IS high impedance from CLKOUT low 3 ns tdis(CLKL-RW) Disable time, R/W high impedance from CLKOUT low 3 ns tdis(CLKL-S) Disable time, MSTRB, IOSTRB high impedance from CLKOUT low 3 ns ten(CLKL-A) Enable time, Address, PS, DS, IS valid from CLKOUT low 2H+3 ns ten(CLKL-RW) Enable time, R/W enabled from CLKOUT low 2H+3 ns ten(CLKL-S) Enable time, MSTRB, IOSTRB enabled from CLKOUT low tv(HOLDA) tw(HOLDA) 2 2H+3 ns Valid time, HOLDA low after CLKOUT low –1 4 ns Valid time, HOLDA high after CLKOUT low –1 4 ns Pulse duration, HOLDA low duration Submit Documentation Feedback 2H–3 Electrical Specifications ns 71 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com CLKOUT tsu(HOLD) tw(HOLD) tsu(HOLD) HOLD tv(HOLDA) HOLDA tv(HOLDA) tw(HOLDA) tdis(CLKL−A) ten(CLKL−A) tdis(CLKL−RW) ten(CLKL−RW) tdis(CLKL−S) ten(CLKL−S) tdis(CLKL−S) ten(CLKL−S) A[22:0] PS, DS, IS D[15:0] R/W MSTRB IOSTRB Figure 5-14. HOLD and HOLDA Timings (HM = 1) 72 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.5.7 Reset, BIO, Interrupt, and MP/MC Timings Table 5-17 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5-15, Figure 5-16, and Figure 5-17). Table 5-17. Reset, BIO, Interrupt, and MP/MC Timing Requirements 5416-120 5416-160 MIN UNIT MAX th(RS) Hold time, RS after CLKOUT low (1) 2 ns th(BIO) Hold time, BIO after CLKOUT low (1) 4 ns 0 ns 4 ns (1) (2) th(INT) Hold time, INTn, NMI, after CLKOUT low th(MPMC) Hold time, MP/MC after CLKOUT low (1) tw(RSL) Pulse duration, RS low (3) (4) 4H + 3 ns tw(BIO)S Pulse duration, BIO low, synchronous 2H + 3 ns tw(BIO)A Pulse duration, BIO low, asynchronous 4H ns tw(INTH)S Pulse duration, INTn, NMI high (synchronous) 2H + 2 ns tw(INTH)A Pulse duration, INTn, NMI high (asynchronous) tw(INTL)S Pulse duration, INTn, NMI low (synchronous) tw(INTL)A Pulse duration, INTn, NMI low (asynchronous) tw(INTL)WKP Pulse duration, INTn, NMI low for IDLE2/IDLE3 wakeup 4H ns 2H + 2 ns 4H ns 7 ns (2) (1) tsu(RS) Setup time, RS before X2/CLKIN low 3 ns tsu(BIO) Setup time, BIO before CLKOUT low (1) 7 ns tsu(INT) Setup time, INTn, NMI, RS before CLKOUT low (1) 7 ns 5 ns tsu(MPMC) (1) (2) (3) (4) Setup time, MP/MC before CLKOUT low (1) These inputs can be driven from an asynchronous source, therefore, there are no specific timing requirements with respect to CLKOUT, however, if setup and hod timings are met, the input will be recognized on the CLKOUT edge referenced. The external interrupts (INT0-INT3, NMI) are synchronized to the core CPU by way of a two-flip-flop synchronizer that samples these inputs with consecutive falling edges of CLKOUT. The input to the interrupt pins is required to represent a1-0-0 sequence at the timing that is corresponding to three CLKOUTs sampling sequence. If the PLL mode is selected, then at power-on sequence, or at wakeup from IDLE3, RS must be held low for at least 50 µs to ensure synchronization and lock-in of the PLL. Note that RS may cause a change in clock frequency, therefore changing the value of H. X2/CLKIN tsu(RS) tw(RSL) RS, INTn, NMI tsu(INT) th(RS) CLKOUT tsu(BIO) th(BIO) BIO tw(BIO)S Figure 5-15. Reset and BIO Timings Submit Documentation Feedback Electrical Specifications 73 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com CLKOUT tsu(INT) tsu(INT) th(INT) INT, NMI tw(INTH)A tw(INTL)A Figure 5-16. Interrupt Timing CLKOUT RS th(MPMC) tsu(MPMC) MP/MC Figure 5-17. MP/MC Timing 74 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.5.8 Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Timings Table 5-18 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5-18). Table 5-18. Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Switching Characteristics 5416-120 5416-160 PARAMETER UNIT MIN MAX td(CLKL-IAQL) Delay time, CLKOUT low to IAQ low –1 4 ns td(CLKL-IAQH) Delay time, CLKOUT low to IAQ high –1 4 ns td(CLKL-IACKL) Delay time, CLKOUT low to IACK low –1 4 ns td(CLKL-IACKH) Delay time, CLKOUT low to IACK high –1 4 ns td(CLKL-A) Delay time, CLKOUT low to address valid –1 4 ns tw(IAQL) Pulse duration, IAQ low 2H – 2 ns tw(IACKL) Pulse duration, IACK low 2H – 2 ns CLKOUT td(CLKL−A) td(CLKL−A) A[22:0] td(CLKL − IAQH) td(CLKL − IAQL) IAQ tw(IAQL) td(CLKL − IACKL) td(CLKL − IACKH) tw(IACKL) IACK Figure 5-18. Instruction Acquisition (IAQ) and Interrupt Acknowledge (IACK) Timings Submit Documentation Feedback Electrical Specifications 75 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com 5.5.9 External Flag (XF) and TOUT Timings Table 5-19 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5-19 and Figure 5-20). Table 5-19. External Flag (XF) and TOUT Switching Characteristics 5416-120 5416-160 PARAMETER UNIT MIN MAX Delay time, CLKOUT low to XF high –1 4 Delay time, CLKOUT low to XF low –1 4 td(TOUTH) Delay time, CLKOUT low to TOUT high –1 4 ns td(TOUTL) Delay time, CLKOUT low to TOUT low –1 4 ns tw(TOUT) Pulse duration, TOUT td(XF) 2H – 4 ns ns CLKOUT td(XF) XF Figure 5-19. External Flag (XF) Timing CLKOUT td(TOUTH) td(TOUTL) TOUT tw(TOUT) Figure 5-20. TOUT Timing 76 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.5.10 Multichannel Buffered Serial Port (McBSP) Timing 5.5.10.1 McBSP Transmit and Receive Timings Table 5-20 and Table 5-21 assume testing over recommended operating conditions (see Figure 5-21 and Figure 5-22). Table 5-20. McBSP Transmit and Receive Timing Requirements (1) 5416-120 5416-160 UNIT MIN MAX tc(BCKRX) Cycle time, BCLKR/X (2) BCLKR/X ext 4P (3) ns tw(BCKRX) Pulse duration, BCLKR/X high or BCLKR/X low (2) BCLKR/X ext 2P–1 (3) ns tsu(BFRH-BCKRL) Setup time, external BFSR high before BCLKR low th(BCKRL-BFRH) Hold time, external BFSR high after BCLKR low tsu(BDRV-BCKRL) Setup time, BDR valid before BCLKR low th(BCKRL-BDRV) Hold time, BDR valid after BCLKR low tsu(BFXH-BCKXL) Setup time, external BFSX high before BCLKX low th(BCKXL-BFXH) Hold time, external BFSX high after BCLKX low tr(BCKRX) Rise time, BCKR/X BCLKR/X ext 6 ns tf(BCKRX) Fall time, BCKR/X BCLKR/X ext 6 ns (1) (2) (3) BCLKR int 8 BCLKR ext 1 BCLKR int 1 BCLKR ext 2 BCLKR int 7 BCLKR ext 1 BCLKR int 2 BCLKR ext 3 BCLKX int 8 BCLKX ext 1 BCLKX int 0 BCLKX ext 2 ns ns ns ns ns ns CLKRP = CLKXP = FSRP = FSXP = 0. If the polaritiy of any of the signals is inverted, then the timing references of that signal are also inverted. Note that in some cases, for example when driving another 54x device McBSP, maximum serial port clocking rates may not be achievable at maximum CPU clock frequency due to transmitted data timings and corresponding receive timing requirements. A separate detailed timing analysis should be performend for each specific McBSP interface. P = 0.5 * processor clock. Submit Documentation Feedback Electrical Specifications 77 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Table 5-21. McBSP Transmit and Receive Switching Characteristics (1) 5416-120 5416-160 PARAMETER MIN Cycle time, BCLKR/X (2) tc(BCKRX) BCLKR/X int (2) tw(BCKRXH) Pulse duration, BCLKR/X high BCLKR/X int tw(BCKRXL) Pulse duration, BCLKR/X low (2) td(BCKRH-BFRV) Delay time, BCLKR high to internal BFSR valid BCLKR/X int td(BCKXH-BFXV) Delay time, BCLKX high to internal BFSX valid tdis(BCKXH-BDXHZ) Disable time, BCLKX high to BDX high impedance following last data bit of transfer DXENA = 0 td(BCKXH-BDXV) Delay time, BCLKX high to BDX valid DXENA = 1 td(BFXH-BDXV) (1) (2) (3) (4) (5) Delay time, BFSX high to BDX valid ONLY applies when in data delay 0 (XDATDLY = 00b) mode UNIT MAX 4P (3) ns D – 1 (4) D + 1 (4) ns C – 1 (4) C + 1 (4) ns BCLKR int –3 3 ns BCLKR ext 0 6 ns BCLKX int –1 5 BCLKX ext 3 11 BCLKX int 6 BCLKX ext 10 BCLKX int – 1 (5) 10 BCLKX ext 3 20 BCLKX int – 1 (5) 20 3 30 BCLKX ext BFSX int –1 BFSX ext (5) 7 3 11 ns ns ns ns CLKRP = CLKXP = FSRP = FSXP = 0. If the polaritiy of any of the signals is inverted, then the timing references of that signal are also inverted. Note that in some cases, for example when driving another 54x device McBSP, maximum serial port clocking rates may not be achievable at maximum CPU clock frequency due to transmitted data timings and corresponding receive timing requirements. A separate detailed timing analysis should be performend for each specific McBSP interface. P = 0.5 * processor clock. T = BCLKRX period = (1 + CLKGDV) * 2P C = BCLKRX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) * 2P when CLKGDV is even D = BCLKRX high pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2 +1) * 2P when CLKGDV is even Minimum delay times also represent minimum output hold times. tc(BCKRX) tw(BCKRXH) tw(BCKRXL) tr(BCKRX) tf(BCKRX) BCLKR td(BCKRH-BFRV) td(BCKRH-BFRV) BFSR (int) tsu(BFRH-BCKRL) th(BCKRL-BFRH) BFSR (ext) tsu(BDRV-BCKRL) BDR th(BCKRL-BDRV) Bit(n-1) (n-2) (n-3) Figure 5-21. McBSP Receive Timings 78 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 tc(BCKRX) tw(BCKRXH) tr(BCKRX) tf(BCKRX) tw(BCKRXL) BCLKX td(BCKXH-BFXV) BFSX (int) th(BCKXL-BFXH) tsu(BFXH-BCKXL) BFSX (ext) BFSX (XDATDLY=00b) td(BCKXH-BDXV) td(BFXH-BDXV) tdis(BCKXH-BDXHZ) BDX Bit 0 td(BCKXH-BDXV) Bit(n-1) (n-2) (n-3) Figure 5-22. McBSP Transmit Timings Submit Documentation Feedback Electrical Specifications 79 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.5.10.2 www.ti.com McBSP General-Purpose I/O Timing Table 5-22 and Table 5-23 assume testing over recommended operating conditions (see Figure 5-23). Table 5-22. McBSP General-Purpose I/O Timing Requirements 5416-120 5416-160 MIN UNIT MAX tsu(BGPIO-COH) Setup time, BGPIOx input mode before CLKOUT high (1) 7 ns th(COH-BGPIO) Hold time, BGPIOx input mode after CLKOUT high (1) 0 ns (1) BGPIOx refers to BCLKRx, BFSRx, BDRx, BCLKXx, or BFSXx when configured as a general-purpose input. Table 5-23. McBSP General-Purpose I/O Switching Characteristics 5416-120 5416-160 PARAMETER td(COH-BGPIO) (1) Delay time, CLKOUT high to BGPIOx output mode (1) UNIT MIN MAX –2 4 ns BGPIOx refers to BCLKRx, BFSRx, BDRx, BCLKXx, or BFSXx when configured as a general-purpose output. tsu(BGPIO-COH) td(COH-BGPIO) CLKOUT th(COH-BGPIO) BGPIOx Input Mode (see Note A) BGPIOx Output Mode (see Note B) A. BGPIOx refers to BCLKRx, BFSRx, BDRx, BCLKXx, or BFSXx when configured as a general-purpose input. B. BGPIOx refers to BCLKRx, BFSRx, BCLKXx, BFSXx, or BDXx when configured as a general-purpose output. Figure 5-23. McBSP General-Purpose I/O Timings 80 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.5.10.3 McBSP as SPI Master or Slave Timing Table 5-24 to Table 5-31 assume testing over recommended operating conditions (see Figure 5-24, Figure 5-25, Figure 5-26, and Figure 5-27). Table 5-24. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 0) (1) 5416-120 5416-160 MASTER MIN tsu(BDRV-BCKXL) Setup time, BDR valid before BCLKX low th(BCKXL-BDRV) (1) (2) UNIT SLAVE MAX MIN MAX 12 2 – 6P (2) ns 4 (2) ns Hold time, BDR valid after BCLKX low 5 + 12P For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1. P = 0.5 * processor clock. Table 5-25. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 0) (1) 5416-120 5416-160 PARAMETER MASTER (2) MIN (3) UNIT SLAVE MAX Hold time, BFSX low after BCLKX low td(BFXL-BCKXH) Delay time, BFSX low to BCLKX high (4) td(BCKXH-BDXV) Delay time, BCLKX high to BDX valid tdis(BCKXL-BDXHZ) Disable time, BDX high impedance following last data bit from BCLKX low tdis(BFXH-BDXHZ) Disable time, BDX high impedance following last data bit from BFSX high 2P– 4 (5) 6P + 17 (5) ns td(BFXL-BDXV) Delay time, BFSX low to BDX valid 4P+ 2 (5) 8P + 17 (5) ns (3) (4) (5) T+4 C+3 –4 5 C–2 C+3 MAX th(BCKXL-BFXL) (1) (2) T–3 C–4 MIN ns ns 6P + 2 (5) 10P + 17 (5) ns ns For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1. T = BCLKX period = (1 + CLKGDV) * 2P C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) *2P when CLKGDV is even FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on BFSX and BFSR is inverted before being used internally. CLKXM = FSXM = 1, CLKRM = FRSRM = 2 for master McBSP CLKXM = CLKRm = FSXM = FSRM = 0 for slave McBSP BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock (BCLKX). P = 0.5 * processor clock. MSB LSB BCLKX th(BCKXL-BFXL) td(BFXL-BCKXH) BFSX tdis(BFXH-BDXHZ) td(BFXL-BDXV) td(BCKXH-BDXV) tdis(BCKXL-BDXHZ) BDX Bit 0 Bit(n-1) tsu(BDRV-BCLXL) BDR Bit 0 (n-2) (n-3) (n-4) th(BCKXL-BDRV) Bit(n-1) (n-2) (n-3) (n-4) Figure 5-24. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0 Submit Documentation Feedback Electrical Specifications 81 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Table 5-26. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 0) (1) 5416-120 5416-160 MASTER MIN MAX tsu(BDRV-BCKXL) Setup time, BDR valid before BCLKX low th(BCKXH-BDRV) Hold time, BDR valid after BCLKX high (1) (2) UNIT SLAVE MIN MAX 12 2 – 6P (2) ns 4 5 + 12P (2) ns For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1. P = 0.5 * processor clock. Table 5-27. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 0) (1) 5416-120 5416-160 PARAMETER MASTER (2) Hold time, BFSX low after BCLKX low (3) th(BCKXL-BFXL) (4) UNIT SLAVE MIN MAX C –3 C+4 MIN MAX ns td(BFXL-BCKXH) Delay time, BFSX low to BCLKX high T–4 T+3 td(BCKXL-BDXV) Delay time, BCLKX low to BDX valid –4 5 6P + 2 (5) 10P + 17 (5) ns tdis(BCKXL-BDXHZ) Disable time, BDX high impedance following last data bit from BCLKX low –2 4 6P – 4 (5) 10P + 17 (5) ns td(BFXL-BDXV) Delay time, BFSX low to BDX valid D–2 D+4 4P + 2 (5) 8P + 17 (5) ns (1) (2) (3) (4) (5) ns For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1. T = BCLKX period = (1 + CLKGDV) * 2P C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) *2P when CLKGDV is even D = BCLKX high pulse width = T/2 when CLKGDV is odd or zero and (CLKGDV/2 + 1) * 2P when CLKGDV is even FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on BFSX and BFSR is inverted before being used internally. CLKXM = FSXM = 1, CLKRM = FRSRM = 2 for master McBSP CLKXM = CLKRm = FSXM = FSRM = 0 for slave McBSP BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock (BCLKX). P = 0.5 * processor clock. MSB LSB BCLKX th(BCKXL-BFXL) td(BFXL-BCKXH) BFSX tdis(BCKXL-BDXHZ) BDX td(BCKXL-BDXV) td(BFXL-BDXV) Bit 0 Bit(n-1) tsu(BDRV-BCKXL) BDR Bit 0 (n-2) (n-3) (n-4) th(BCKXH-BDRV) Bit(n-1) (n-2) (n-3) (n-4) Figure 5-25. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0 82 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Table 5-28. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 1) (1) 5416-120 5416-160 MASTER MIN MAX tsu(BDRV-BCKXH) Setup time, BDR valid before BCLKX high th(BCKXH-BDRV) Hold time, BDR valid after BCLKX high (1) (2) UNIT SLAVE MIN MAX 12 2 – 6P (2) ns 4 5 + 12P (2) ns For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1. P = 0.5 * processor clock. Table 5-29. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 1) (1) 5416-120 5416-160 PARAMETER MASTER (2) Hold time, BFSX low after BCLKX high (3) th(BCKXH-BFXL) (4) UNIT SLAVE MIN MAX T–3 T+4 D–4 D+3 –4 5 D–2 D+3 MIN MAX ns td(BFXL-BCKXL) Delay time, BFSX low to BCLKX lowTNote9543 td(BCKXL-BDXV) Delay time, BCLKX low to BDX valid tdis(BCKXH-BDXHZ) Disable time, BDX high impedance following last data bit from BCLKX high tdis(BFXH-BDXHZ) Disable time, BDX high impedance following last data bit from BFSX high 2P – 4 (5) 6P + 17 (5) ns td(BFXL-BDXV) Delay time, BFSX low to BDX valid 4P + 2 (5) 8P + 17 (5) ns (1) (2) (3) (4) (5) ns 6P + 2 (5) 10P + 17 (5) ns ns For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1. T = BCLKX period = (1 + CLKGDV) * 2P D = BCLKX high pulse width = T/2 when CLKGDV is odd or zero and (CLKGDV/2 + 1) * 2P when CLKGDV is even FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on BFSX and BFSR is inverted before being used internally. CLKXM = FSXM = 1, CLKRM = FRSRM = 2 for master McBSP CLKXM = CLKRm = FSXM = FSRM = 0 for slave McBSP BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock (BCLKX). P = 0.5 * processor clock. LSB MSB BCLKX th(BCKXH-BFXL) td(BFXL-BCKXL) BFSX td(BFXL-BDXV) tdis(BFXH-BDXHZ) td(BCKXL-BDXV) tdis(BCKXH-BDXHZ) BDX Bit 0 Bit(n-1) tsu(BDRV-BCKXH) BDR Bit 0 (n-2) (n-3) (n-4) th(BCKXH-BDRV) Bit(n-1) (n-2) (n-3) (n-4) Figure 5-26. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1 Submit Documentation Feedback Electrical Specifications 83 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Table 5-30. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 1) (1) 5416-120 5416-160 MASTER MIN MAX tsu(BDRV-BCKXL) Setup time, BDR valid before BCLKX low th(BCKXL–BDRV) Hold time, BDR valid after BCLKX low (1) (2) UNIT SLAVE MIN MAX 12 2 – 6P (2) ns 4 5 + 12P (2) ns For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1. P = 0.5 * processor clock. Table 5-31. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 1) (1) 5416-120 5416-160 PARAMETER MASTER (2) Hold time, BFSX low after BCLKX high (3) th(BCKXH-BFXL) (4) UNIT SLAVE MIN MAX D–3 D+4 MIN MAX ns td(BFXL-BCKXL) Delay time, BFSX low to BCLKX low T–4 T+3 td(BCKXH-BDXV) Delay time, BCLKX high to BDX valid –4 5 6P + 2 (5) 10P + 17 (5) ns tdis(BCKXH-BDXHZ) Disable time, BDX high impedance following last data bit from BCLKX high –2 4 6P – 4 (5) 10P + 17 (5) ns td(BFXL-BDXV) Delay time, BFSX low to BDX valid C–2 C+4 4P + 2 (5) 8P + 17 (5) ns (1) (2) (3) (4) (5) ns For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1. T = BCLKX period = (1 + CLKGDV) * 2P C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) * 2P when CLKGDV is even D = BCLKX high pulse width = T/2 when CLKGDV is odd or zero and (CLKGDV/2 + 1) * 2P when CLKGDV is even FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on BFSX and BFSR is inverted before being used internally. CLKXM = FSXM = 1, CLKRM = FRSRM = 2 for master McBSP CLKXM = CLKRm = FSXM = FSRM = 0 for slave McBSP BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock (BCLKX). P = 0.5 * processor clock. MSB LSB BCLKX th(BCKXH-BFXL) td(BFXL-BCKXL) BFSX tdis(BCKXH-BDXHZ) BDX td(BCKXH-BDXV) td(BFXL-BDXV) Bit 0 Bit(n-1) tsu(BDRV-BCKXL) BDR Bit 0 (n-2) (n-3) (n-4) th(BCKXL-BDRV) Bit(n-1) (n-2) (n-3) (n-4) Figure 5-27. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1 84 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 5.5.11 Host-Port Interface Timing 5.5.11.1 HPI8 Mode Table 5-32 and Table 5-33 assume testing over recommended operating conditions and P = 0.5 * processor clock (see Figure 5-28 through Figure 5-31). In the following tables, DS refers to the logical OR of HCS, HDS1, and HDS2. HD refers to any of the HPI data bus pins (HD0, HD1, HD2, etc.). HAD stands for HCNTL0, HCNTL1, and HR/W. Table 5-32. HPI8 Mode Timing Requirements 5416-120 5416-160 MIN UNIT MAX tsu(DSL-HBV) Setup time, HBIL and HAD valid before DS low (when HAS is not used), or HBIL and HAD valid before HAS low 6 ns th(DSL-HBV) Hold time, HBIL and HAD valid after DS low (when HAS is not used), or HBIL and HAD valid after HAS low 3 ns tsu(HSL-DSL) Setup time, HAS low before DS low 8 ns tw(DSL) Pulse duration, DS low 13 ns tw(DSH) Pulse duration, DS high 7 ns tsu(HDV-DSH) Setup time, HD valid before DS high, HPI write 3 ns th(DSH-HDV)W Hold time, HD valid after DS high, HPI write 2 ns tsu(GPIO-COH) Setup time, HDx input valid before CLKOUT high, HDx configured as general-purpose input 3 ns th(GPIO-COH) Hold time, HDx input valid before CLKOUT high, HDx configured as general-purpose input 0 ns Submit Documentation Feedback Electrical Specifications 85 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Table 5-33. HPI8 Mode Switching Characteristics 5416-120 5416-160 PARAMETER MIN ten(DSL-HD) td(DSL-HDV1) Enable time, HD driven from DS low Delay time, DS low to HD valid for first byte of an HPI read 36P + 10 – tw(DSH) Case 1b: Memory accesses when DMAC is active in 32-bit mode and tw(DSH) ≥ 36P (1) 10 Case 1c: Memory accesses when DMAC is active in 16-bit mode and tw(DSH) < I8P (1) 18P + 10 – tw(DSH) Case 1d: Memory accesses when DMAC is active in 16-bit mode and tw(DSH) ≥ I8P (1) 10 Case 2a: Memory accesses when DMAC is inactive and tw(DSH) < 10P (1) 10P + 10 – tw(DSH) Case 2b: Memory accesses when DMAC is inactive and tw(DSH) ≥ 10P (1) 10 Case 3: Register accesses 10 Delay time, DS low to HD valid for second byte of an HPI read th(DSH-HDV)R Hold time, HD valid after DS high, for a HPI read tv(HYH-HDV) Valid time, HD valid after HRDY high td(DSH-HYH) Delay time, DS high to HRDY low Delay time, DS high to HRDY high (2) 10 Case 1a: Memory accesses when DMAC is active in 32-bit mode and tw(DSH) < 36P (1) td(DSL-HDV2) td(DSH-HYL) 0 UNIT MAX (2) 10 0 ns ns ns ns 2 ns 8 ns Case 1a: Memory accesses when DMAC is active in 16-bit mode (1) 18P + 6 Case 1b: Memory accesses when DMAC is active in 32-bit mode (1) 36P + 6 Case 2: Memory accesses when DMAC is inactive (1) 10P + 6 Case 3: Write accesses to HPIC register (3) 6P + 6 ns td(HCS-HRDY) Delay time, HCS low/high to HRDY low/high 6 ns td(COH-HYH) Delay time, CLKOUT high to HRDY high 9 ns td(COH-HTX) Delay time, CLKOUT high to HINT change 6 ns td(COH-GPIO) Delay time, CLKOUT high to HDx output change. HDx is configured as a general-purpose output 5 ns (1) (2) (3) 86 DMAS stands for direct memory access controller. The HPI8 shares the internal DMA bus with the DMAC, thus HPI8 access times are affected by DMAC activity. The HRDY output is always high when the HCS input is high, regardless of DS timings. This timing applies when writing a one to the DSPINT bit or HINT bit of the HPIC register. All other writes to the HPIC occur asynchronously, and do not cause HRDY to be deasserted. Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 Second Byte First Byte Second Byte HAS tsu(HBV-DSL) tsu(HSL-DSL) th(DSL-HBV) HAD (see Note A) Valid tsu(HBV-DSL)‡ Valid th(DSL-HBV) (see Note B) HBIL HCS tw(DSH) tw(DSL) HDS td(DSH-HYH) td(DSH-HYL) HRDY ten(DSL-HD) td(DSL-HDV2) td(DSL-HDV1) th(DSH-HDV)R HD READ Valid Valid tsu(HDV-DSH) Valid tv(HYH-HDV) th(DSH-HDV)W HD WRITE Valid Valid Valid td(COH-HYH) Processor CLK A. HAD refers to HCNTL0, HCNTL1, and HR/W. B. When HAS is not used (HAS always high) Figure 5-28. Using HDS to Control Accesses (HCS Always Low) Submit Documentation Feedback Electrical Specifications 87 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com HCS HDS td(HCS-HRDY) HRDY Figure 5-29. Using HCS to Control Accesses CLKOUT td(COH-HTX) HINT Figure 5-30. HINT Timing In Figure 5-31, GPIOx refers to HD0, HD1, HD2, ...HD7, when the HD bus is configured for general-purpose input/output (I/O). CLKOUT tsu(GPIO-COH) th(GPIO-COH) GPIOx Input Mode (see Note A) td(COH-GPIO) GPIOx Output Mode (see Note A) Figure 5-31. GPIOx Timings 88 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com 5.5.11.2 SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 HPI16 Mode Table 5-34 and Table 5-35 assume testing over recommended operating conditions and P = 0.5 * processor clock (see Figure 5-32 through Figure 5-34). In the following tables, DS refers to the logical OR of HCS, HDS1, and HDS2, and HD refers to any of the HPI data bus pins (HD0, HD1, HD2, etc.). These timings are shown assuming that HDS is the signal controlling the transfer. See the TMS320C54x DSP Reference Set,Volume 5: Enhanced Peripherals (literature number SPRU302) for additional information. Table 5-34. HPI16 Mode Timing Requirements 5416-120 5416-160 MIN UNIT MAX tsu(HBV-DSL) Setup time, HR/W valid before DS falling edge 6 ns th(DSL-HBV) Hold time, HR/W valid after DS falling edge 5 ns tsu(HAV-DSH) Setup time, address valid before DS rising edge (write) 5 tsu(HAV-DSL) Setup time, address valid before DS falling edge (read) th(DSH-HAV) Hold time, address valid after DS rising edge 1 ns tw(DSL) Pulse duration, DS low 30 ns tw(DSH) Pulse duration, DS high 10 ns Reads 10P + 30 (1) Writes 10P + 10 (1) Memory accesses with 16-bit DMA activity. Reads 16P + 30 (1) Writes 16P + 10 (1) Memory accesses with 32-bit DMA activity. Reads 24P + 30 (1) Writes 24P + 10 (1) Memory accesses with no DMA activity. tc(DSH-DSH) Cycle time, DS rising edge to next DS rising edge ns –(4P– 6) (1) ns ns tsu(HDV-DSH)W Setup time, HD valid before DS rising edge 8 ns th(DSH-HDV)W Hold time, HD valid after DS rising edge, write 2 ns (1) P = 0.5 * processor clock. Submit Documentation Feedback Electrical Specifications 89 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 www.ti.com Table 5-35. HPI16 Mode Switching Characteristics 5416-120 5416-160 PARAMETER MIN td(DSL-HDD) td(DSL-HDV1) Delay time, DS low to HD driven Delay time, DS low to HD valid for first word of an HPI read 0 10 Case 1a: Memory accesses initiated immediately following a write when DMAC is active in 32-bit mode and tw(DSH) was < 26P 48P + 20 – tw(DSH) Case 1b: Memory access not immediately following a write when DMAC is active in 32-bit mode 24P + 20 Case 1c: Memory accesses initiated immediately following a write when DMAC is active in 16-bit mode and tw(DSH) was < 18P 32P + 20 – tw(DSH) Case 1d: Memory accesses not immediately following a write when DMAC is active in 16-bit mode 20P + 20 – tw(DSH) Case 2b: Memory accesses not immediately following a write when DMAC is inactive 10P + 20 Memory writes when no DMA is active Delay time, DS high to HRDY Memory writes with one or more 16-bit DMA channels active high Memory writes with one or more 32-bit DMA channels active tv(HYH-HDV) Valid time, HD valid after HRDY high th(DSH-HDV)R Hold time, HD valid after DS rising edge, read td(COH-HYH) Delay time, CLKOUT rising edge to HRDY high td(DSL-HYL) td(DSH-HYL) ns 16P + 20 Case 2a: Memory accesses initiated immediately following a write when DMAC is inactive and tw(DSH) was < 10P td(DSH-HYH) UNIT MAX 10P + 5 16P + 5 ns 24P + 5 7 ns 6 ns 5 ns Delay time, DS low to HRDY low 12 ns Delay time, DS high to HRDY low 12 ns 1 HCS tw(DSH) tc(DSH−DSH) HDS tsu(HBV−DSL) tw(DSL) tsu(HBV−DSL) th(DSL−HBV) th(DSL−HBV) HR/W tsu(HAV−DSL) th(DSH−HAV) HA[17:0] Valid Address Valid Address th(DSH−HDV)R td(DSL−HDV1) td(DSL−HDV1) Data HD[15:0] td(DSL−HDD) th(DSH−HDV)R Data td(DSL−HDD) tv(HYH−HDV) tv(HYH−HDV) HRDY td(DSL−HYL) td(DSL−HYL) Figure 5-32. Nonmultiplexed Read Timings 90 Electrical Specifications Submit Documentation Feedback TMS320VC5416 Fixed-Point Digital Signal Processor www.ti.com SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 HCS tw(DSH) tc(DSH−DSH) HDS tsu(HBV−DSL) tsu(HBV−DSL) th(DSL−HBV) th(DSL−HBV) HR/W tsu(HAV−DSH) tw(DSL) th(DSH−HAV) HA[17:0] Valid Address Valid Address tsu(HDV−DSH)W tsu(HDV−DSH)W th(DSH−HDV)W th(DSH−HDV)W HD[15:0] Data Valid Data Valid td(DSH−HYH) HRDY td(DSH−HYL) Figure 5-33. Nonmultiplexed Write Timings HRDY td(COH−HYH) CLKOUT Figure 5-34. HRDY Relative to CLKOUT Submit Documentation Feedback Electrical Specifications 91 TMS320VC5416 Fixed-Point Digital Signal Processor SPRS095P – MARCH 1999 – REVISED OCTOBER 2008 6 www.ti.com Mechanical Data The following mechanical package diagram(s) reflect the most current released mechanical data available for the designated device(s). 6.1 Package Thermal Resistance Characteristics Table 6-1provides the estimated thermal resistance characteristics for the recommended package types used on the device. Table 6-1. Thermal Resistance Characteristics 92 PARAMETER GGU PACKAGE PGE PACKAGE UNIT RθJA 38 56 °C/W RθJC 5 5 °C/W Mechanical Data Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 13-May-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) DVC5416PGE160IDWLD ACTIVE LQFP PGE 144 60 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 0 320VC5416 PGE 160 TMS TMS320VC5416GWS120 ACTIVE NFBGA GWS 144 160 Non-RoHS & Green SNPB Level-3-220C-168 HR -40 to 85 DVC5416GWS 120 TMS320VC5416GWS160 ACTIVE NFBGA GWS 144 160 Non-RoHS & Green SNPB Level-3-220C-168 HR -40 to 85 DVC5416GWS 160 TMS320VC5416PGE120 ACTIVE LQFP PGE 144 60 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 0 320VC5416PGE 120 TMS TMS320VC5416PGE160 ACTIVE LQFP PGE 144 60 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 0 320VC5416 PGE 160 TMS TMS320VC5416ZWS120 ACTIVE NFBGA ZWS 144 160 RoHS & Green SNAGCU Level-3-260C-168 HR -40 to 85 DVC5416ZWS 120 TMS320VC5416ZWS160 ACTIVE NFBGA ZWS 144 160 RoHS & Green SNAGCU Level-3-260C-168 HR -40 to 85 DVC5416ZWS 160 TX5416PGE ACTIVE LQFP PGE 144 60 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 0 320VC5416 PGE 160 TMS (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 13-May-2021 Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of