User's Guide
SLVU951 – August 2013
TPS22967EVM-023 Single 4A Load Switch
The TPS22967EVM-023 evaluation module contains a single channel, ultra low ON resistance, 4-A load
switch with controlled turn-on and adjustable rise time
1
2
3
4
5
6
7
Contents
Description ................................................................................................................... 2
1.1
Typical Applications ................................................................................................ 2
1.2
Features ............................................................................................................. 2
Electrical Performance Specifications .................................................................................... 3
Schematic .................................................................................................................... 4
List of Test Points ........................................................................................................... 4
Layout ........................................................................................................................ 5
5.1
Typical Test Setups ................................................................................................ 8
5.2
Test Setup Equipment List ........................................................................................ 9
5.3
Test Procedure (Standalone Setup) ........................................................................... 10
5.4
RON Test Procedure .............................................................................................. 10
5.5
Trise/Ton Tfall/Toff Test Procedure ............................................................................ 10
Performance Data and Typical Characteristic Curves ................................................................ 10
6.1
Trise/Tfall Curves ................................................................................................. 11
Bill of Materials ............................................................................................................. 13
List of Figures
1
TPS22967EVM-023 Schematic ...........................................................................................
2
TPS22967EVM-023 Top Assembly.......................................................................................
5
3
TPS22967EVM-023 Topside ..............................................................................................
6
4
TPS22967EVM-023 Bottomside ..........................................................................................
7
5
TPS22967EVM-023 Recommended Ron Test Set Up
................................................................
TPS22967EVM-023 Recommended Rise Time Test Set Up .........................................................
TPS22967EVM-023 Trise/Ton VIN=5V VBIAS=5V ct=1nF Load =10Ω. ...........................................
TPS22967EVM-023 Tfall/Toff VIN=5V VBIAS=5V ct=1nF Load =10Ω. ............................................
8
6
7
8
4
9
11
12
List of Tables
1
The Functions of Each Test Points .......................................................................................
4
2
EVM Components List ....................................................................................................
13
SLVU951 – August 2013
Submit Documentation Feedback
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
1
Description
1
www.ti.com
Description
The TPS22967 is a small, ultra-low ON-resistance (RON) single channel load switch with controlled turn on.
The device contains a low Rds(ON) N-channel MOSFET that can operate over an input voltage range of 0.8
V to 5.5 V and can support a maximum continuous current of up to 4-A. The switch is controlled by an
active high on/off input (ON), which is capable of interfacing directly with low-voltage GPIO control signals.
In the TPS22967, a 225-Ω on-chip load resistor is added for quick output discharge (QOD). When the
switch is turned off, the output of the switch is discharged to ground through the 225-Ω load resistor. The
rise time of the device is internally controlled in order to avoid in-rush current and can be adjusted using
an external ceramic capacitor on the CT pin.
The TPS22967 is available in a small, space-saving 2mm x 2mm 8-pin SON package with integrated
thermal pad allowing for high power dissipation.
1.1
Typical Applications
•
•
•
•
•
•
•
•
1.2
Features
•
•
•
•
•
•
•
•
2
Ultrabooks™
Notebooks/Netbooks
Tablet PC
Consumer Electronics
Set-top Boxes/Residential Gateways
Industrial Systems
Telecom Systems
Solid State Drivers (SSD)
Integrated single channel load switch
Input voltage range: 0.8V to 5.5V
Ultra-low on-resistance (22 mΩ typical)
4A maximum continuous switch current
Low threshold control input
Adjustable slew-rate control
Quick Output Discharge transistor
SON 8-pin package with thermal pad
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
SLVU951 – August 2013
Submit Documentation Feedback
Electrical Performance Specifications
www.ti.com
2
Electrical Performance Specifications
ELECTRICAL CHARACTERISTICS
Unless otherwise noted, the specification in the following table applies over the operating ambient
temperature –40°C ≤ TA ≤ 85°C (Full) and VBIAS = 5.0 V. Typical values are for TA = 25°C.
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
UNIT
50
75
µA
2
µA
POWER SUPPLIES AND CURRENTS
IIN(VBIAS-ON)
VBIAS quiescent current
IOUT = 0, VIN = VON = VBIAS = 5.0 V
Full
IIN(VBIAS-OFF)
VBIAS shutdown current
VON = GND, VOUT = 0 V
Full
IIN(VIN-OFF)
VIN off-state supply current
VON = GND, VOUT = 0 V
ION
ON pin input leakage current
VON = 5.5 V
VIN = 5.0 V
0.2
VIN = 3.3 V
0.02
VIN =1.8 V
Full
VIN = 0.8 V
µA
0.01
0.005
Full
0.5
µA
RESISTANCE CHARACTERISTICS
VIN = 5.0 V
VIN = 3.3 V
VIN = 1.8 V
RON
IOUT = –200 mA,
VBIAS = 5.0 V
ON-state resistance
VIN = 1.5 V
VIN = 1.2 V
VIN = 0.8 V
RPD
Output pulldown resistance
SLVU951 – August 2013
Submit Documentation Feedback
VIN = 5.0 V, VON = 0 V, IOUT = 15 mA
25°C
22
Full
25°C
35
22
Full
25°C
22
22
22
33
35
22
Full
Full
33
35
Full
25°C
33
35
Full
25°C
33
35
Full
25°C
33
33
35
225
300
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
mΩ
mΩ
mΩ
mΩ
mΩ
mΩ
Ω
3
Schematic
www.ti.com
Users may refer to Datasheet Document SLVSC42 for additional Electrical Specifications.
3
Schematic
Figure 1. TPS22967EVM-023 Schematic
4
List of Test Points
Table 1. The Functions of Each Test Points
4
Test Points
Name
Description
J1
VIN
DC Input to VIN
J2
VOUT
VOUT Connection
JP1
VBIAS
Connects VBIAS to VIN
JP2
ON
Connects ON to VIN or GND
JP3
C1
Connects C1 to VIN
JP4
C5
Connects C5 to VOUT
JP5
R1
Connects R1 to VOUT
JP6
R2
Connects R2 to VOUT
TP1
VIN
VIN of TPS22967
TP2
ON
ON of TPS22967
TP3
VIN SEN
Sense connect to VIN of TPS22967
TP4
VBIAS
VBIAS of TPS22967
TP5
VOUT SEN
Sense connect to VOUT of TPS22967
TP6
VOUT
VOUT of TPS22967
TP7
GND
Ground Connection
TP8
GND
Ground Connection
TP9
GND
Ground Connection
TP10
GND
Ground Connection
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
SLVU951 – August 2013
Submit Documentation Feedback
Layout
www.ti.com
5
Layout
Figure 2. TPS22967EVM-023 Top Assembly
SLVU951 – August 2013
Submit Documentation Feedback
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
5
Layout
www.ti.com
Figure 3. TPS22967EVM-023 Topside
6
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
SLVU951 – August 2013
Submit Documentation Feedback
Layout
www.ti.com
Figure 4. TPS22967EVM-023 Bottomside
SLVU951 – August 2013
Submit Documentation Feedback
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
7
Layout
5.1
www.ti.com
Typical Test Setups
Figure 5. TPS22967EVM-023 Recommended Ron Test Set Up
8
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
SLVU951 – August 2013
Submit Documentation Feedback
Layout
www.ti.com
Figure 6. TPS22967EVM-023 Recommended Rise Time Test Set Up
5.2
Test Setup Equipment List
•
•
•
•
•
•
Voltage Source:
– 1 Power Source capable of 10V 10A.
Multimeters:
– 2 voltmeters
Output Loads:
– Electronic Load or Resistor(If testing 4A operation of the switch at 5.5V a 22W power rated resistor
is needed)
Oscilloscope:
– 2 channel 100MHz
Signal Generator:
– Dual Channel Preferred
Recommended Wire Gauge: 18 AWG
SLVU951 – August 2013
Submit Documentation Feedback
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
9
Performance Data and Typical Characteristic Curves
5.3
www.ti.com
Test Procedure (Standalone Setup)
Figure 5 shows a typical setup for RON testing of the EVM. VBIAS voltage must be present for the device
to function. Place a shunt across JP1 to connect VBIAS to VIN voltage source, if VIN supply is used below
2.5V remove the shunt and connect VBIAS voltage to a voltage source greater or equal to 2.5V.
5.4
RON Test Procedure
1. Setup the EVM per Figure 5.
2. Set SOURCE1 level to 5.0V.
3. Place a shunt on JP2 shorting pins 1 to 2. This connects ON to VIN voltage, ON voltage must be
between 1.2V and 5.5V for a valid ON state. (When testing RON it is desired to have the switch
operating in the always ON condition.)
4. Place a load on VOUT.
5. Turn on SOURCE1.
6. Record the voltage reading from Meter1, record the input current reading from Source1. Calculate RON
by dividing Meter1 voltage level by the current reading from Source1. The results will be the RON value
for the Switch.
7. Turn off Source1.
5.5
Trise/Ton Tfall/Toff Test Procedure
1. Set up the EVM per Figure 6.
2. Set SOURCE1 level to 5.0V VBIAS is operational between 2.5V and 5.25V, Datasheet limits are
specified with VBIAS set at 5.0V.
3. Remove shunt from JP2.
4. Place a load on VOUT1 (a 10Ω 3.25W resistor is recommended for this test).
5. Set signal generator outputs to 0-2Vpp levels, 10–100Hz, and 25% duty cycle. Connect signal
generator output to TP2.
6. Turn on SOURCE1.
7. Turn ON the signal generator output.
8. Trise and Ton can be observed from the oscilloscope channel2. A detailed description of tR, tON, tF, and
tOFF are listed in the TPS22967 Datasheet under the Switching Characteristics Section.
9. Turn off Source1, and the signal generator output.
6
Performance Data and Typical Characteristic Curves
Figure 7 through Figure 8 present typical performance curves for TPS22967EVM-023.
10
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
SLVU951 – August 2013
Submit Documentation Feedback
Performance Data and Typical Characteristic Curves
www.ti.com
6.1
Trise/Tfall Curves
Figure 7. TPS22967EVM-023 Trise/Ton VIN=5V VBIAS=5V ct=1nF Load =10Ω.
SLVU951 – August 2013
Submit Documentation Feedback
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
11
Performance Data and Typical Characteristic Curves
www.ti.com
Figure 8. TPS22967EVM-023 Tfall/Toff VIN=5V VBIAS=5V ct=1nF Load =10Ω.
12
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
SLVU951 – August 2013
Submit Documentation Feedback
Bill of Materials
www.ti.com
7
Bill of Materials
Table 2 shows the EVM components list according to the schematic shown in Figure 1.
Table 2. EVM Components List
-002
RefDes
Value
Description
Size
Part Number
MFR
0
C1, C5
DNP
Capacitor, Ceramic, 25V, X7R, 20%
0603
Std
Std
1
C2
1 µF
Capacitor, Ceramic, 25V, Y5R, 20%
0603
GRM188F51E105ZA12D
Murata
1
C3
1 nf
Capacitor, Ceramic, 50V, X7R, 10%
0603
ECJ-1VB1H102K
Panasonic
1
C4
0.1 µF
Capacitor, Ceramic, 50V, Y5R, 20%
0603
GRM188F51H104ZA01D
Murata
2
C6, C7
0.01 µF
Capacitor, Ceramic, 50V, X7R, 10%
0603
0603B103K500BT
Vishay
2
J1, J2
ED120/2DS
Terminal Block 2-pin, 15-A, 5.1mm
0.40 x 0.35 inch
ED120/2DS
OST
5
JP1, JP3, JP4, JP5,
JP6
PEC02SAAN
Header, Male 2-pin, 100mil spacing
0.100 inch x 2
PEC02SAAN
Sullins
1
JP2
PEC03SAAN
Header, Male3-pin, 100mil spacing
0.100 inch x 3
PEC03SAAN
Sullins
0
R1, R2
DNP
Resistor, Chip, 1.16W, x%
0805
Std
Std
6
TP1, TP2, TP3,
TP4, TP5, TP6
5010
Test Point, Red, Thru Hole Compact Style
0.125 x 0.125 inch
5005
Keystone
4
TP7, TP8, TP9,
TP10
5011
Test Point, Black, Thru Hole Compact Style
0.125 x 0.125 inch
5006
Keystone
0
U1
TPS22965DSG
IC, 6-A Load Switch with Controlled Turn-on
SON-8
TPS22965DSG
TI
1
U1
TPS22967DSG
IC, 4-A Load Switch with Controlled Turn-on
SON-8
TPS22967DSG
TI
Shunt, Black
100-mil
929950-00
3M
HVL023
Any
THT-13-457-10
Brady
Count
2
1
—
PCB, 2 In x 1.5 In x 0.062 In
1
NA
Label (see Note 5)
SLVU951 – August 2013
Submit Documentation Feedback
1.25 x 0.25 inch
TPS22967EVM-023 Single 4A Load Switch
Copyright © 2013, Texas Instruments Incorporated
13
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated