TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
USB Charging Port Controller and Power Switch with Load Detection
Check for Samples: TPS2543
FEATURES
DESCRIPTION
•
The TPS2543 is a USB charging port controller and
power switch with an integrated USB 2.0 high-speed
data line (D+/D–) switch. The TPS2543 provides the
electrical signatures on D+/D– to support the
following charging schemes:
• USB Battery Charging Specification 1.2;
• Chinese Telecom Standard YD/T 1591-2009;
• Divider Mode, Compliant with Apple iPod, iPhone
(1A), and iPad (2A) Mobile Digital Devices. (1)
1
•
•
•
•
•
•
•
•
•
•
•
•
D+/D– CDP/DCP Modes per USB Battery
Charging Specification 1.2
D+/D– Shorted Mode per Chinese
Telecommunication Industry Standard YD/T
1591-2009
D+/D– Divider Modes 2.0V/2.7V and 2.7/2.0V
Compliant with 1A and 2A Apple Mobile Digital
Devices
Automatic Selection of D+/D– Mode for an
Attached Device
Supports Sleep-Mode Charging and
Mouse/Keyboard (Low-Speed Only) Wake Up
Load Detection for Both Power Supply Control
in S4/S5 Charging and Port Power
Management in all Charge Modes
Compatible with USB 2.0 and 3.0 Power Switch
Requirements
73-mΩ (typ) High-Side MOSFET
Adjustable Current-Limit up to 3.0 A (typ)
Operating Range: 4.5 V to 5.5 V
Drop-In Compatible with TPS2540/40A
Available in 16-Pin QFN (3x3) Package
UL Listed and CB File No. E169910
The TPS2543 can be configured to automatically
select the D+/D– mode needed to charge an attached
device. The TPS2543 provides load detection via the
STATUS pin that allows for both power supply control
in S4/S5 charging and the ability to manage port
power in a multi-port application. Additionally, system
wake up (from S3) with a mouse/keyboard (low
speed only) is fully supported in the TPS2343.
The TPS2543 73-mΩ power-distribution switch is
intended for applications where heavy capacitive
loads and short-circuits are likely to be encountered.
Two programmable current thresholds provide
flexibility for setting current limits and load detect
thresholds.
APPLICATIONS
•
•
•
USB Ports (Host and Hubs)
Notebook Desktop PCs
Universal Wall Charging Adapters
(1)
Apple, iPod, iPhone, and iPad are trademarks of Apple Inc.,
registered in the U.S. and other countries.
15
14
To Portable Device à
FAULT
GND
ILIM_HI
16
ILIM_LO
TPS2543 RTE PACKAGE AND TYPICAL APPLICATION DIAGRAM
Power Bus
RSTATUS
(10 kW)
13
IN
1
12
OUT
DM_OUT
2
11
DM_IN
DP_OUT
3
10
DP_IN
ILIM_SEL
4
9
STATUS Signal
Fault Signal
6
7
8
EN
CLT1
CLT2
CLT3
Thermal Pad
5
4.5V – 5.5V
STATUS
ILIM Select
Power Switch EN
Mode Select I/O
0.1 uF
IN
OUT
TPS2543
RFAULT
(10 kW)
CUSB
ILIM_LO
ILIM_HI
STATUS
RILIM_HI
FAULT
ILIM_SEL
EN
CTL1
CTL2
CTL3
VBUS
DD+
GND
RILIM_LO
GND
DM_IN
DP_IN
DM_OUT
DP_OUT
USB
Connector
To Host Controller à
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
TPS2543
SLVSBA6 – FEBRUARY 2012
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION (1)
(1)
TA
PACKAGE
DEVICE
TOP-SIDE MARKING
–40°C to 125°C
QFN16
TPS2543
2543
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range, voltages are referenced to GND (unless otherwise noted)
Voltage range
IN, EN, ILIM_LO, ILIM_HI, FAULT, STATUS, ILIM_SEL,
CTL1, CTL2, CTL3, OUT
IN to OUT
LIMIT
UNIT
–0.3 to 7
V
–7 to 7
DP_IN, DM_IN, DP_OUT, DM_OUT
–0.3 to (IN + 0.3) or 5.7
Input clamp current
DP_IN, DM_IN, DP_OUT, DM_OUT
±20
mA
Continuous current in SDP or CDP
mode
DP_IN to DP_OUT or DM_IN to DM_OUT
±100
mA
Continuous current in BC1.2 DCP
mode
DP_IN to DM_IN
±50
mA
Continuous output current
OUT
Continuous output sink current
FAULT, STATUS
25
mA
Continuous output source current
ILIM_LO, ILIM_HI
Internally limited
mA
ESD rating
HBM
2
kV
HBM wrt GND and each other, DP_IN, DM_IN
8
Internally limited
CDM
Operating junction temperature, TJ
(1)
500
V
–40 to Internally limited
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
THERMAL INFORMATION
THERMAL METRIC (1)
TPS2543
RTE (16 PIN)
θJA
Junction-to-ambient thermal resistance
53.4
θJCtop
Junction-to-case (top) thermal resistance
51.4
θJB
Junction-to-board thermal resistance
17.2
ψJT
Junction-to-top characterization parameter
3.7
ψJB
Junction-to-board characterization parameter
20.7
θJCbot
Junction-to-case (bottom) thermal resistance
3.9
(1)
2
UNITS
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
RECOMMENDED OPERATING CONDITIONS
voltages are referenced to GND (unless otherwise noted)
MIN
VIN
Input voltage, IN
NOM
MAX
UNIT
4.5
5.5
V
Input voltage, logic-level inputs, EN, CTL1, CTL2, CTL3, ILIM_SEL
0
5.5
V
Input voltage, data line inputs, DP_IN, DM_IN, DP_OUT, DM_OUT
0
VIN
V
VIH
High-level input voltage, EN, CTL1, CTL2, CTL3, ILIM_SEL
1.8
V
VIL
Low-level input voltage, EN, CTL1, CTL2, CTL3, ILIM_SEL
0.8
V
Continuous current, data line inputs, SDP or CDP mode, DP_IN to DP_OUT, DM_IN to
DM_OUT
±30
mA
±15
mA
Continuous current, data line inputs, BC1.2 DCP mode, DP_IN to DM_IN
IOUT
Continuous output current, OUT
0
2.5
A
Continuous output sink current, FAULT, STATUS
0
10
mA
RILIM_XX
Current-limit set resistors
16.9
750
kΩ
TJ
Operating virtual junction temperature
–40
125
°C
ELECTRICAL CHARACTERISTICS
Unless otherwise noted: –40 ≤ TJ ≤ 125°C, 4.5 V ≤ VIN ≤ 5.5 V, VEN = VIN, VILIM_SEL = VIN, VCTL1 = VCTL2 = VCTL3 = VIN. RFAULT =
RSTATUS = 10 kΩ, RILIM_HI = 20 kΩ, RILIM_LO = 80.6 kΩ. Positive currents are into pins. Typical values are at 25°C. All voltages
are with respect to GND.
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
POWER SWITCH
RDS(on)
On resistance
(1)
tr
OUT voltage rise time
tf
OUT voltage fall time
ton
OUT voltage turn-on time
toff
OUT voltage turn-off time
IREV
Reverse leakage current
TJ = 25°C, IOUT = 2 A
73
84
–40°C ≤ TJ ≤ 85°C, IOUT = 2 A
73
105
–40°C ≤ TJ ≤ 125°C, IOUT = 2 A
73
120
0.7
1.0
1.60
0.2
0.35
0.5
2.7
4
1.7
3
VIN = 5 V, CL = 1 µF, RL = 100 Ω (see Figure 23 and
Figure 24)
VIN = 5V, CL = 1 µF, RL = 100 Ω (see Figure 23 and
Figure 25)
VOUT = 5.5 V, VIN = VEN = 0 V, –40 ≤ TJ ≤ 85°C,
Measure IOUT
2
mΩ
ms
ms
µA
DISCHARGE
RDCHG
OUT discharge resistance
VOUT = 4 V, VEN = 0 V
400
500
630
Ω
tDCHG
OUT discharge hold time
Time VOUT < 0.7 V (see Figure 26)
205
310
450
ms
(1)
Pulse-testing techniques maintain junction temperature close to ambient temperature; Thermal effects must be taken into account
separately.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
3
TPS2543
SLVSBA6 – FEBRUARY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Unless otherwise noted: –40 ≤ TJ ≤ 125°C, 4.5 V ≤ VIN ≤ 5.5 V, VEN = VIN, VILIM_SEL = VIN, VCTL1 = VCTL2 = VCTL3 = VIN. RFAULT =
RSTATUS = 10 kΩ, RILIM_HI = 20 kΩ, RILIM_LO = 80.6 kΩ. Positive currents are into pins. Typical values are at 25°C. All voltages
are with respect to GND.
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
EN, ILIMSEL, CTL1, CTL2, CTL3 INPUTS
Input pin rising logic threshold
voltage
1
1.35
1.70
Input pin falling logic threshold
voltage
0.85
1.15
1.45
Hysteresis (2)
Input current
200
Pin voltage = 0 V or 5.5 V
–0.5
VILIM_SEL = 0 V, RILIM_LO = 210 kΩ
205
V
mV
0.5
µA
ILIMSEL CURRENT LIMIT
OUT short circuit current limit (3)
IOS
Response time to OUT shortcircuit (2)
tIOS
240
275
625
680
VILIM_SEL = 0 V, RILIM_LO = 80.6 kΩ
575
VILIM_SEL = 0 V, RILIM_LO = 22.1 kΩ
2120
2275 2430
VILIM_SEL = VIN, RILIM_HI = 20 kΩ
2340
2510 2685
VILIM_SEL = VIN, RILIM_HI = 16.9 kΩ
2770
2970 3170
VIN = 5.0 V, R = 0.1Ω, lead length = 2 inches (see
Figure 27)
1.5
mA
µs
SUPPLY CURRENT
IIN_OFF
Disabled IN supply current
IIN_ON
Enabled IN supply current
VEN = 0 V, VOUT = 0 V, –40 ≤ TJ ≤ 85°C
2
VCTL1 = VCTL2 = VIN, VCTL3 = 0 V or VIN, VILIM_SEL = 0 V
155
210
VCTL1 = VCTL2 = VIN, VCTL3 = 0V, VILIM_SEL = VIN
175
230
VCTL1 = VCTL2 = VIN, VCTL3 = VIN, VILIM_SEL = VIN
185
240
VCTL1 = 0V, VCTL2 = VCTL3 = VIN
205
260
4.1
4.3
µA
µA
UNDERVOLTAGE LOCKOUT
VUVLO
IN rising UVLO threshold voltage
Hysteresis
3.9
(2)
100
V
mV
FAULT
Output low voltage
IFAULT = 1 mA
Off-state leakage
VFAULT = 6.5 V
Over current FAULT rising and
falling deglitch
5
8.2
100
mV
1
µA
12
ms
100
mV
1
µA
STATUS
Output low voltage
ISTATUS = 1 mA
Off-state leakage
VSTATUS = 6.5 V
THERMAL SHUTDOWN
Thermal shutdown threshold
155
Thermal shutdown threshold in
current-limit
135
Hysteresis (2)
(2)
(3)
4
°C
20
These parameters are provided for reference only and do not constitute part of TI's published device specifications for purposes of TI's
product warranty.
Pulse-testing techniques maintain junction temperature close to ambient temperature; Thermal effects must be taken into account
separately.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
ELECTRICAL CHARACTERISTICS, HIGH-BANDWIDTH SWITCH
Unless otherwise noted: –40 ≤ TJ ≤ 125°C, 4.5 V ≤ VIN ≤ 5.5 V, VEN = VIN, VILIM_SEL = VIN, VCTL1 = VCTL2 = VCTL3 = VIN. RFAULT =
RSTATUS = 10 kΩ, RILIM_HI = 20 kΩ, RILIM_LO = 80.6 kΩ, Positive currents are into pins. Typical values are at 25°C. All voltages
are with respect to GND.
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
HIGH-BANDWIDTH ANALOG SWITCH
DP/DM switch on resistance
VDP/DM_OUT = 0 V, IDP/DM_IN = 30 mA
2
4
VDP/DM_OUT = 2.4 V, IDP/DM_IN = –15 mA
3
6
Switch resistance mismatch between
DP / DM channels
VDP/DM_OUT = 0 V, IDP/DM_IN = 30 mA
0.05
0.15
VDP/DM_OUT = 2.4 V, IDP/DM_IN = –15 mA
0.05
0.15
DP/DM switch off-state capacitance (1)
VEN = 0 V, VDP/DM_IN = 0.3 V, Vac = 0.6 Vpk-pk,
f = 1 MHz
3
3.6
6.2
DP/DM switch on-state capacitance
(2)
Ω
Ω
pF
VDP/DM_IN = 0.3 V, Vac = 0.6 Vpk-pk, f = 1 MHz
5.4
OIRR
Off-state isolation (3)
VEN = 0 V, f = 250 MHz
33
dB
XTALK
On-state cross channel isolation (3)
f = 250 MHz
52
dB
Off state leakage current
VEN = 0 V, VDP/DM_IN = 3.6 V, VDP/DM_OUT = 0 V,
measure IDP/DM_OUT
0.1
BW
Bandwidth (–3dB) (3)
RL = 50 Ω
tpd
Propagation delay (3)
tSK
Skew between opposite transitions of the
same port (tPHL – tPLH)
(1)
(2)
(3)
1.5
pF
µA
2.6
GHz
0.25
ns
0.1
0.2
ns
The resistance in series with the parasitic capacitance to GND is typically 250 Ω.
The resistance in series with the parasitic capacitance to GND is typically 150 Ω
These parameters are provided for reference only and do not constitute part of TI's published device specifications for purposes of TI's
product warranty.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
5
TPS2543
SLVSBA6 – FEBRUARY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS, CHARGING CONTROLLER
Unless otherwise noted: –40 ≤ TJ ≤ 125°C, 4.5 V ≤ VIN ≤ 5.5 V, VEN = VIN, VILIM_SEL = VIN, VCTL1 = 0 V, VCTL2 = VCTL3 = VIN.
RFAULT = RSTATUS = 10 kΩ, RILIM_HI = 20 kΩ, RILIM_LO = 80.6 kΩ, Positive currents are into pins. Typical values are at 25°C. All
voltages are with respect to GND.
PARAMETER
TEST CONDITIONS
SHORTED MODE
MIN
TYP
MAX
UNIT
125
200
Ω
VCTL1 = VIN, VCTL2 = VCTL3 = 0V
DP_IN / DM_IN shorting resistance
DIVIDER1 MODE
DP_IN Divider1 output voltage
1.9
2.0
2.1
V
DM_IN Divider1 output voltage
2.57
2.7
2.84
V
DP_IN output impedance
8
10.5
12.5
kΩ
DM_IN output impedance
8
10.5
12.5
kΩ
DP_IN Divider2 output voltage
2.57
2.7
2.84
V
DM_IN Divider2 output voltage
DIVIDER2 MODE
IOUT = 1A
1.9
2.0
2.1
V
DP_IN output impedance
8
10.5
12.5
kΩ
DM_IN output impedance
8
10.5
12.5
kΩ
0.5
0.6
0.7
V
0.4
V
CHARGING DOWNSTREAM PORT
VCTL1 = VCTL2 = VCTL3 = VIN
VDP_IN = 0.6 V,
–250 µA < IDM_IN < 0 µA
VDM_SRC
DM_IN CDP output voltage
VDAT_REF
DP_IN rising lower window thresholdfor
VDM_SRC activation
Hysteresis
VLGC_SRC
0.25
(1)
50
DP_IN rising upper window thresholdfor
VDM_SRC de-activation
0.8
hysteresis (1)
IDP_SINK
VDP_IN = 0.6 V
70
100
µA
635
700
765
mA
50
Load detect set time
200
275
ms
1.9
3
4.2
s
Power wake short circuit current limit
32
55
78
mA
IOUT falling power wake reset current
detection threshold
23
45
67
mA
10.7
15
Load detect reset time
Reset current hysteresis
VCTL1 = VCTL2 = 0V, VCTL3 = VIN
(1)
5
Power wake reset time
6
mA
140
LOAD DETECT – POWER WAKE
(1)
mV
40
hysteresis (1)
IOS_PW
V
VCTL1 = VCTL2 = VCTL3 = VIN
IOUT rising load detect current threshold
tLD_SET
1
100
DP_IN sink current
LOAD DETECT – NON POWER WAKE
ILD
mV
mA
20.6
s
These parameters are provided for reference only and do not constitute part of TI's published device specifications for purposes of TI's
product warranty.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
TYPICAL CHARACTERISTICS
POWER SWITCH ON RESISTANCE
vs
TEMPERATURE
REVERSE LEAKAGE CURRENT
vs
TEMPERATURE
0.3
100
0.25
Reverse Leakage Current (µA)
On Resistance (mΩ)
90
80
70
60
0.2
0.15
0.1
0.05
50
−40 −25 −10
5
20 35 50 65 80
Junction Temperature (°C)
95
0
−40 −25 −10
110 125
5
20 35 50 65 80
Junction Temperature (°C)
95
110 125
G001
G002
Figure 1.
Figure 2.
OUT DISCHARGE RESISTANCE
vs
TEMPERATURE
OUT SHORT CIRCUIT CURRENT LIMIT
vs
TEMPERATURE
580
3000
OUT Short Circuit Current Limit (mA)
OUT Discharge Resistance (Ω)
560
3500
VIN = 4.5 V
VIN = 5 V
VIN = 5.5 V
540
520
500
480
460
−40 −25 −10
2500
2000
1500
RILIM_LO = 210 kΩ
RILIM_LO = 80.6 kΩ
RILIM_HI = 20 kΩ
RILIM_HI = 16.9 kΩ
1000
500
5
20 35 50 65 80
Junction Temperature (°C)
95
110 125
0
−40 −25 −10
5
20 35 50 65 80
Junction Temperature (°C)
95
110 125
G003
Figure 3.
G004
Figure 4.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
7
TPS2543
SLVSBA6 – FEBRUARY 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
DISABLED IN SUPPLY CURRENT
vs
TEMPERATURE
ENABLED IN SUPPLY CURRENT - SDP
vs
TEMPERATURE
1.2
190
VIN = 5.5 V
180
Enabled IN Supply Current (µA)
Disabled IN Supply Current (µA)
1
0.8
0.6
0.4
0.2
0
−40
VIN = 4.5 V
VIN = 5 V
VIN = 5.5 V
170
160
150
Device configured for SDP
VILIMSEL = 0 V
140
−20
0
20
40
60
Junction Temperature (°C)
80
130
−40 −25 −10
100
5
20 35 50 65 80
Junction Temperature (°C)
95
110 125
G005
G006
Figure 5.
Figure 6.
ENABLED IN SUPPLY CURRENT - CDP
vs
TEMPERATURE
ENABLED IN SUPPLY CURRENT - DCP AUTO
vs
TEMPERATURE
220
230
Enabled IN Supply Current (µA)
Enabled IN Supply Current (µA)
210
240
VIN = 4.5 V
VIN = 5 V
VIN = 5.5 V
200
190
180
170
VIN = 4.5 V
VIN = 5 V
VIN = 5.5 V
220
210
200
190
Device configured for CDP
160
−40 −25 −10
5
20 35 50 65 80
Junction Temperature (°C)
95
Device configured for DCP AUTO
110 125
180
−40 −25 −10
5
20 35 50 65 80
Junction Temperature (°C)
G007
Figure 7.
8
95
110 125
G008
Figure 8.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
TYPICAL CHARACTERISTICS (continued)
STATUS AND FAULT OUTPUT LOW VOLTAGE
vs
SINKING CURRENT
DATA TRANSMISSION CHARACTERISTICS
vs
FREQUENCY
0
700
TJ = −40°C
TJ = 25°C
TJ = 125°C
600
500
Transmission Gain - dB
Output Low Voltage (mV)
-5
400
300
200
-10
-15
-20
100
VIN = 4.5 V
0
0
1
2
3
4
5
6
7
Sinking Current (mA)
8
9
10
-20
0.01
G009
0.1
1
10
Frequency - GHz
Figure 9.
Figure 10.
OFF STATE DATA SWITCH ISOLATION
vs
FREQUENCY
ON STATE CROSS-CHANNEL ISOLATION
vs
FREQUENCY
60
XTALK - ON State Cross-Channel Isolation - dB
80
OIRR - Off State Isolation - dB
50
40
30
20
10
70
60
50
40
30
20
10
0
0
0.01
0.1
1
10
0.01
0.1
1
10
Frequency - GHz
Frequency - GHz
Figure 11.
Figure 12.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
9
TPS2543
SLVSBA6 – FEBRUARY 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
EYE DIAGRAM USING USB COMPLIANCE TEST PATTERN
(with data switch)
0.5
0.5
0.4
0.4
0.3
0.3
0.2
0.2
Differential Signal (V)
Differential Signal (V)
EYE DIAGRAM USING USB COMPLIANCE TEST PATTERN
(with no switch)
0.1
0
–0.1
–0.2
0.1
0
–0.1
–0.2
–0.3
–0.3
–0.4
–0.4
–0.5
–0.5
0
0.2
0.4
0.6
0.8
1 1.2
Time (ns)
1.4
1.6
1.8
0
2
0.2
0.4
G013
0.6
0.8
1 1.2
Time (ns)
1.4
1.6
Figure 13.
Figure 14.
IOUT RISING LOAD DETECT THRESHOLD
AND OUT SHORT CIRCUIT CURRENT LIMIT
vs
TEMPERATURE
LOAD DETECT SET TIME
vs
TEMPERATURE
1.8
2
G014
230
740
RILIM_LO = 80.6 kΩ
720
225
Load Detect Set Time (ms)
Current (mA)
700
680
660
640
220
215
210
205
620
IOS - OUT Short Circuit Current Limit
ILD - IOUT Rising Load Detect Threshold
600
−40 −25 −10
5
20 35 50 65 80
Junction Temperature (°C)
95
110 125
200
−40 −25 −10
5
20 35 50 65 80
Junction Temperature (°C)
G015
Figure 15.
10
95
110 125
G016
Figure 16.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
TYPICAL CHARACTERISTICS (continued)
POWER WAKE CURRENT LIMIT
vs
TEMPERATURE
TURN-ON RESPONSE
59
Power Wake Current Limit (mA)
58
57
VOUT
2 V/div
56
VEN
5 V/div
55
54
53
52
−40 −25 −10
RLOAD = 5 Ω
CLOAD = 150 µF
IIN
500 mA/div
t - Time - 1 ms/div
5
20 35 50 65 80
Junction Temperature (°C)
95
G021
110 125
G017
Figure 17.
Figure 18.
TURN-OFF RESPONSE
DEVICE ENABLED INTO SHORT CIRCUIT
V/FAULT
5 V/div
VOUT
2 V/div
VEN
5 V/div
VEN
5 V/div
RLOAD = 5 Ω
CLOAD = 150 µF
RILM_LO = 80.6 kΩ
IIN
500 mA/div
IIN
500 mA/div
t - Time - 1 ms/div
Figure 19.
G022
t - Time - 2 ms/div
G023
Figure 20.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
11
TPS2543
SLVSBA6 – FEBRUARY 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
DEVICE ENABLED INTO SHORT CIRCUIT - THERMAL
CYCLING
RILM_HI = 20 kΩ
V/FAULT
5 V/div
SHORT CIRCUIT to FULL LOAD RECOVERY
V/FAULT
5 V/div
VEN
5 V/div
VOUT
2 V/div
IIN
1 A/div
IIN
2 A/div
t - Time - 5 ms/div
Figure 21.
12
RILIM_HI = 20 kΩ
RLOAD = 5 Ω
CLOAD = 150 µF
G024
Submit Documentation Feedback
t - Time - 2 ms/div
Figure 22.
G025
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
PARAMETER MEASUREMENT DESCRIPTION
OUT
RL
VOUT
CL
tr
tf
90%
10%
Figure 23. OUT Rise/Fall Test Load
Figure 24. Power-On and Off Timing
5V
VEN
50 %
50 %
VOUT
ton
tDCHG
toff
0V
90 %
VOUT
10 %
Figure 25. Enable Timing, Active High Enable
Figure 26. OUT Discharge During Mode Change
IOS
IOUT
tIOS
Figure 27. Output Short Circuit Parameters
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
13
TPS2543
SLVSBA6 – FEBRUARY 2012
www.ti.com
DEVICE INFORMATION
IN
1
DM_OUT
2
ILIM_HI
ILIM_LO
GND
FAULT
TPS2543 RTE PACKAGE
(Top View)
16
15
14
13
12
OUT
11
DM_IN
DP_IN
Thermal Pad
4
9
5
6
7
8
CLT3
ILIM_SEL
CLT2
10
CLT1
3
EN
DP_OUT
STATUS
PIN FUNCTIONS
NO.
(1)
14
NAME
TYPE (1)
P
DESCRIPTION
Input voltage and supply voltage; connect 0.1 μF or greater ceramic capacitor from IN to GND as close
to the device as possible
1
IN
2
DM_OUT
I/O
D– data line to USB host controller
3
DP_OUT
I/O
D+ data line to USB host controller
4
ILIM_SEL
I
Logic-level input signal used to control the charging mode, current limit threshold, and load detection;
see the control truth table
5
EN
I
Logic-level input for turning the power switch and the signal switches on/off; logic low turns off the signal
and power switches and holds OUT in discharge.
6
CTL1
I
7
CTL2
I
8
CTL3
I
Logic-level inputs used to control the charging mode and the signal switches; see the control truth table
9
STATUS
O
Active-low open-drain output, asserted in load detection conditions
10
DP_IN
I/O
D+ data line to downstream connector
11
DM_IN
I/O
D– data line to downstream connector
12
OUT
P
Power-switch output
13
FAULT
O
Active-low open-drain output, asserted during over-temperature or current limit conditions
14
GND
P
Ground connection
15
ILIM_LO
I
External resistor used to set the low current-limit threshold and the load detection current threshold. A
resistor to ILIM_LO is optional; see Current-Limit Settings in DETAILED DESCRIPTION.
16
ILIM_HI
I
External resistor used to set the high current-limit threshold
NA
PowerPAD
Internally connected to GND; used to heat-sink the part to the circuit board traces. Connect to GND
plane.
G = Ground, I = Input, O = Output, P = Power
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
FUNCTIONAL BLOCK DIAGRAM
Current
Sense
CS
IN
OUT
Disable + UVLO+Discharge
ILIM_HI
Current
Limit
Current Limit
select
Charge
Pump
ILIM_LO
GND
OC
8-ms Deglitch
OTSD
Thermal
Sense
UVLO
ILIM_SEL
Driver
LD cur set
EN
discharge
FAULT
8-ms Deglitch
(falling edge)
DM_OUT
DM_IN
DP_OUT
DP_IN
ILIM_SEL
OC
CTL1
CTL2
Logic
control
CDP
Detection
DCP
Detection
Divider
Mode
Auto-Detection
LD cur set
Discharge
STATUS
CTL3
Discharge
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
15
TPS2543
SLVSBA6 – FEBRUARY 2012
www.ti.com
DETAILED DESCRIPTION
Overview
The following overview references various industry standards. It is always recommended to consult the most upto-date standard to ensure the most recent and accurate information. Rechargeable portable equipment requires
an external power source to charge its batteries. USB ports are a convenient location for charging because of an
available 5 V power source. Universally accepted standards are required to make sure host and client-side
devices operate together in a system to ensure power management requirements are met. Traditionally, USB
host ports following the USB 2.0 specification must provide at least 500 mA to downstream client-side devices.
Because multiple USB devices can be attached to a single USB port through a bus-powered hub, it is the
responsibility of the client-side device to negotiate its power allotment from the host to ensure the total current
draw does not exceed 500 mA. In general, each USB device is granted 100 mA and may request more current in
100 mA unit steps up to 500 mA. The host may grant or deny based on the available current.
Additionally, the success of USB has made the mini-USB connector a popular choice for wall adapter cables.
This allows a portable device to charge from both a wall adapter and USB port with only one connector. One
common difficulty has resulted from this. As USB charging has gained popularity, the 500 mA minimum defined
by USB 2.0 or 900 mA for USB 3.0 has become insufficient for many handset and personal media players which
need a higher charging rate. Wall adapters can provide much more current than 500mA/900mA. Several new
standards have been introduced defining protocol handshaking methods that allow host and client devices to
acknowledge and draw additional current beyond the 500mA/900mA minimum defined by USB 2.0/3.0 while still
using a single micro-USB input connector.
The TPS2543 supports three of the most common protocols:
• USB Battery Charging Specification BC1.2
• Chinese Telecommunications Industry Standard YD/T 1591-2009
• Divider Mode
All three methods have similarities and differences, but the biggest commonality is that all three define three
types of charging ports that provide charging current to client-side devices. These charging ports are defined as:
• Standard Downstream Port (SDP)
• Charging Downstream Port (CDP)
• Dedicated Charging Port (DCP)
BC1.2 defines a Charging Port as a downstream facing USB port that provides power for charging portable
equipment.
Table 1 shows the differences between these ports according to BC1.2 .
Table 1. Operating Modes
PORT TYPE
SUPPORT USB
2.0 COMMUNICATION
MAX. ALLOWABLE CURRENT
DRAW BY PORTABLE DEVICE (A)
SDP (USB 2.0)
Yes
0.5
SDP (USB 3.0)
Yes
0.9
CDP
Yes
1.5
DCP
No
1.5
BC1.2 defines the protocol necessary to allow portable equipment to determine what type of port it is connected
to so that it can allot its maximum allowable current draw. The hand-shaking process has two steps. During step
one, the primary detection, the portable equipment outputs a nominal 0.6-V output on its D+ line and reads the
voltage input on its D- line. The portable device concludes it is connected to an SDP if the voltage is less than
the nominal data detect voltage of 0.3 V. The portable device concludes that it is connected to a Charging Port if
the D- voltage is greater than the nominal data detect voltage of 0.3 V and less than 0.8 V. The second step, the
secondary detection, is necessary for portable equipment to determine between a CDP and a DCP. The portable
device outputs a nominal 0.6 V output on its D- line and reads the voltage input on its D+ line. The portable
device concludes it is connected to a CDP if the data line being read remains less than the nominal data detect
voltage of 0.3 V. The portable device concludes it is connected to a DCP if the data line being read is greater
than the nominal data detect voltage of 0.3V and less than 0.8 V.
16
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
Standard Downstream Port (SDP) USB 2.0/USB 3.0
An SDP is a traditional USB port that follows USB 2.0/3.0 protocol and supplies a minimum of 500 mA/900 mA
per port. USB 2.0/3.0 communications is supported, and the host controller must be active to allow charging.
Charging Downstream Port (CDP)
A CDP is a USB port that follows USB BC1.2 and supplies a minimum of 1.5 A per port. It provides power and
meets USB 2.0 requirements for device enumeration. USB 2.0 communications is supported, and the host
controller must be active to allow charging. What separates a CDP from an SDP is the host-charge handshaking
logic that identifies this port as a CDP. A CDP is identifiable by a compliant BC1.2 client device and allows for
additional current draw by the client device.
The CDP hand-shaking process is two steps. During step one the portable equipment outputs a nominal 0.6 V
output on its D+ line and reads the voltage input on its D- line. The portable device concludes it is connected to
an SDP if the voltage is less than the nominal data detect voltage of 0.3 V. The portable device concludes that it
is connected to a Charging Port if the D- voltage is greater than the nominal data detect voltage of 0.3V and less
than 0.8 V.
The second step is necessary for portable equipment to determine between a CDP and a DCP. The portable
device outputs a nominal 0.6 V output on its D- line and reads the voltage input on its D+ line. The portable
device concludes it is connected to a CDP if the data line being read remains less than the nominal data detect
voltage of 0.3 V. The portable device concludes it is connected to a DCP if the data line being read is greater
than the nominal data detect voltage of 0.3V and less than 0.8 V.
Dedicated Charging Port (DCP)
A DCP only provides power and does not provide data connection to an upstream port. A DCP is identified by
the electrical characteristics of its data lines. The TPS2543 emulates two common charging standards namely,
BC1.2 and Chinese Telecommunications Industry Standard YD/T 1591-2009, and one brand unique DCP
charging scheme which will be referred to as Divider scheme.
DCP BC 1.2 and YD/T 1591-2009
Both standards defines that the D+ and D- data lines should be shorted together with a maximum series
impedance of 200 Ω. This is shown in Figure 28.
D- Out
VBUS
TPS2543
D-
2V
750mA is measured by the TPS2543 it switches to Divider 2 scheme and test to see if the peripheral
device will still charge at a high current. If it does then it stays in Divider 2 scheme otherwise it will revert to
Divider 1 scheme.
TPS2543
To USB 2.0 Host
DCP Auto
BC1.2 CDP/SDP
D-
BC1.2 DCP
D+
From Charging
Peripheral
Divider 1/2
High BW Data Line SW
Controlled by CTL/EN pins
18
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
DCP Forced Shorted / DCP Forced Divider 1
In this mode the device is permanently set to one of the DCP schemes (BC 1.2/ YD/T 1591-2009 or Divider 1) as
commanded by its control pin setting per device truth table.
High-Bandwidth Data Line Switch
The TPS2543 passes the D+ and D- data lines through the device to enable monitoring and handshaking while
supporting charging operation. A wide bandwidth signal switch is used, allowing data to pass through the device
without corrupting signal integrity. The data line switches are turned on in any of CDP or SDP operating modes.
The EN input also needs to be at logic High for the data line switches to be enabled.
NOTE
1. While in CDP mode, the data switches are ON even while CDP handshaking is occurring.
2. The data line switches are OFF if EN or all CTL pins are held low, or if in DCP mode. They are not
automatically turned off if the power switch (IN to OUT) is in current limit.
3. The data switches are for USB 2.0 differential pair only. In the case of a USB 3.0 host, the super speed
differential pairs must be routed directly to the USB connector without passing through the TPS2543.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
19
TPS2543
SLVSBA6 – FEBRUARY 2012
www.ti.com
Device Operation
Please refer to the simplified device state diagram in Figure 31. Power-on-reset (POR) holds device in initial
state while output is held in discharge mode. Any POR event will take the device back to initial state. After POR
clears, device goes to the next state depending on the CTL lines as shown in Figure 31.
DCP_Auto
Reset
DCP_SHORT/
DCP_DIVIDER
Initial
DCP Forced
DCH/SDP/
CDP
DCH
Done
DCH
DCP_Auto
Discharge
(310 ms)
1111
1110
DCH/SDP
CDP
110X/
010X
Not SDP1
DCP Auto
SDP1
Not CDP
Note:
1) All shaded boxes are device charging modes
2) See below table for CTL settings corresponding to
flow line conditions
3) Mouse / keyboard wake function not shown
CDP
1111
Device Control Pins
Flow Line Condition CTL1
DCH
CDP
SDP2
1110
SDP1
SDP2
Not SDP2
DCP_SHORT
DCP_DIVIDER
DCP_Auto
CTL2
0
1
1
1
0
1
1
0
0
CTL3
0
1
1
1
1
0
0
1
0
0
1
1
0
0
0
1
1
1
ILIM_SEL
X
1
0
X
X
X
X
X
X
Figure 31. TPS2543 Charging States
Output Discharge
To allow a charging port to renegotiate current with a portable device, TPS2543 uses the OUT discharge
function. It proceeds by turning off the power switch while discharging OUT, then turning back on the power
switch to reassert the OUT voltage. This discharge function is automatically applied as shown in device state
diagram.
20
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
Mouse/Key Board Wake Function
The TPS2543 supports low speed HID (human interface device like mouse/key board) wake function. It does not
support Full Speed HID. There are two scenarios under which wake on mouse is supported by the TPS2543.
They are:
1. CDP/SDP2 (111X) to DCP/Auto (011X)
2. SDP1 (010X) to DCP/Auto (011X)
Below description illustrates wake on mouse operation for scenario 1, same holds true for scenario 2.
When a low speed compliant device is attached to the TPS2543, charging port D- line will be pulled high in its
idle state (mouse/keyboard not activated). TPS2543 will monitor D- data line continuously. When device is in
CDP (1111) or SDP2 (1110) or SDP1 (010X) mode and system is commanded to go to sleep state, the device
CTL setting is also changed. Assuming it is changed to DCP/Auto, 011X, having previously detected a HID
attachment the device will simply ignore the command to go to DCP/Auto mode and stay in CDP/SDP2 state to
support wake on mouse function. When the USB low speed HID is activated (clicked) while system is in S3
(sleep) mode the high speed switch within the TPS2543 allows the transfer of signal from the HID device to the
USB host. The USB host subsequently wakes the system and changes CTL setting of the TPS2543 back to
CDP/SDP2 mode. Activating (clicking) the low speed device makes the D- data line go back low momentarily,
this triggers an internal timer within the TPS2543 to count down. If after ~64ms the CTL lines are still set at 011X
(DCP/Auto) the device will immediately switch to DCP/Auto mode and disconnect the mouse from the host. To
prevent this, the CTL setting must be made in less then 64 ms after HID device activation otherwise mouse/KB
function will be lost. See Figure 32 scope plot for an event sequence where mouse connection is maintained at
wake.
Mouse Wake from Sleep
VOUT
DM_IN High
System in Sleep
CTL1 = 1 within 64ms of
sys wake, TPS2543 stays
in SDP/CDP and mouse
connection is maintained
VOUT
2 V/div
CTL1 = 0 TPS2543
detects mouse and
ignores going to DCP
VDM_IN
1 V/div
Mouse Clicked here
system wakes
VCTL1
1 V/div
Figure 32. Mouse Wake from Sleep Scope Plot
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
21
TPS2543
SLVSBA6 – FEBRUARY 2012
www.ti.com
Device Truth Table (TT)
Device TT lists all valid bias combinations for the three control pins CTL1-3 and ILIM_SEL pin and their
corresponding charging mode. It is important to note that the TT purposely omits matching charging modes of the
TPS2543 with global power states (S0-S5) as device is agnostic to system power states. The TPS2543 monitors
its CTL inputs and will transition to whatever charging state it is commanded to go to (except when LS HID
device is detected). For example if sleep charging is desired when system is in standby or hibernate state then
user must set TPS2543 CTL pins to correspond to DCP_Auto charging mode per below table. When system is
put back to operation mode then set control pins to correspond to SDP or CDP mode and so on.
Table 2. Truth Table
CTL1
CTL2
CTL3
ILIM_SEL
MODE
CURRENT
LIMIT
SETTING
0
0
0
0
Discharge
NA
OFF
0
0
0
1
Discharge
NA
OFF
0
0
1
0
DCP_Auto
ILIM_HI
(1)
(2)
(3)
(4)
(5)
IOS_PW & ILIM_HI
STATUS OUTPUT
(Active low)
OUT held low
OFF
(1)
0
0
1
1
DCP_Auto
0
1
0
0
SDP
ILIM_LO
OFF
0
1
0
1
SDP
ILIM_HI
OFF
0
1
1
0
DCP_Auto
ILIM_HI
OFF
COMMENT
Data Lines Disconnected
DCP load present
(2)
Data Lines Disconnected and Load Detect
Function Active
Data Lines connected
Data Lines Disconnected
DCP load present
(3)
0
1
1
1
DCP_Auto
ILIM_HI
1
0
0
0
DCP _Shorted
ILIM_LO
OFF
1
0
0
1
DCP_Shorted
ILIM_HI
OFF
1
0
1
0
DCP / Divider1
ILIM_LO
OFF
1
0
1
1
DCP / Divider1
ILIM_HI
OFF
1
1
0
0
SDP
ILIM_LO
OFF
1
1
0
1
SDP
ILIM_HI
OFF
1
1
1
0
SDP (4)
ILIM_LO
OFF
1
1
1
1
CDP (4)
ILIM_HI
CDP load present (5)
Data Lines Disconnected and Load Detect
Function Active
Device Forced to stay in DCP BC 1.2 charging
mode
Device Forced to stay in DCP Divider 1
Charging Mode
Data Lines Connected
Data Lines Connected and Load Detect Active
TPS2543 : Current limit (IOS) is automatically switched between IOS_PW and the value set by ILIM_HI according to the Load Detect –
Power Wake functionality.
DCP Load present governed by the “Load Detection – Power Wake” limits.
DCP Load present governed by the “Load Detection – Non Power Wake” limits.
No OUT discharge when changing between 1111 and 1110.
CDP Load present governed by the “Load Detection – Non Power Wake” limits and BC 1.2 primary detection.
Table 3 can be used as an aid to program the TPS2543 per system states however not restricted to below
settings only.
Table 3. Control Pin Settings Matched to System Power States
SYSTEM
GLOBAL
POWER
STATE
CTL1
CTL2
CTL3
ILIM_SEL
CURRENT LIMIT
SETTING
S0
SDP
1
1
0
1 or 0
ILIM_HI / ILIM_LO
S0
SDP, no discharge to / from CDP
1
1
1
0
ILIM_LO
S0
CDP, load detection with ILIM_LO + 60mA thresholds or if a
BC1.2 primary detection occurs
1
1
1
1
ILIM_HI
Auto mode, load detection with power wake thresholds
0
0
1
1
ILIM_HI
Auto mode, no load detection
0
0
1
0
ILIM_HI
S3
Auto mode, keyboard/mouse wake up, load detection with
ILIM_LO + 60 mA thresholds
0
1
1
1
ILIM_HI
S3
Auto mode, keyboard/mouse wake-up, no load detection
0
1
1
0
ILIM_HI
S3
SDP, keyboard/mouse wake-up
0
1
0
1 or 0
ILIM_HI / ILIM_LO
S4/S5
S3/S4/S5
22
TPS2543 CHARGING MODE
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TPS2543
TPS2543
www.ti.com
SLVSBA6 – FEBRUARY 2012
Load Detect
TPS2543 offers system designers unique power management strategy not available in the industry from similar
devices. There are two power management schemes supported by the TPS5243 via the STATUS pin, they are:
1. Power Wake (PW)
2. Port Power Management (PPM)
Either feature may be implemented in a system depending on power savings goals for the system. In general
Power Wake feature is used mainly in mobile systems like a notebook where it is imperative to save battery
power when system is in deep sleep (S4/S5) state. On the other hand Port Power Management feature would be
implemented where multiple charging ports are supported in the same system and system power rating is not
capable of supporting full charging on multiple ports simultaneously.
Power Wake
Goal of power wake feature is to save system power when system is in S4/S5 state. In S4/S5 state system is in
deep sleep and typically running of the battery; so every “mW” in system power savings will translate to
extending battery life. In this state the TPS2543 will monitor charging current at the OUT pin and provide a
mechanism via the STATUS pin to switch-out the high power DC-DC controller and switch-in a low power LDO
when charging current requirement is