User's Guide
SLUU826 – January 2012
Using the TPS53310EVM-755, A 3-A Eco-mode™
Integrated Switcher With Master-Slave
The TPS53310EVM-755 evaluation module (EVM) is a high-efficiency evaluation platform with two
TPS53310 3-A, integrated FET, step-down converters working in a Master-Slave synchronization scheme.
The two outputs are 1.5 V/3 A (master) and 1.2 V/3 A (slave) from a 3.3-V or 5-V input bus. The EVM
uses the TPS53310 synchronous buck controller with integrated switcher.
1
2
3
4
5
6
7
8
9
Contents
Description ................................................................................................................... 3
1.1
Typical Applications ................................................................................................ 3
1.2
Features ............................................................................................................. 3
Electrical Performance Specifications .................................................................................... 3
Schematic .................................................................................................................... 5
Test Setup ................................................................................................................... 6
4.1
Test Equipment ..................................................................................................... 6
4.2
Recommended Test Setup ....................................................................................... 7
Configuration ................................................................................................................ 8
5.1
5Vin Option (J1: 5Vin Option) .................................................................................... 8
5.2
Mode Selection (J2: MST Mode) ................................................................................. 8
5.3
Mode Selection (J7: SLV Mode) ................................................................................. 8
5.4
Synchronization (J5: SYNC) ...................................................................................... 8
5.5
Master Enable (J4: EN_MST) .................................................................................... 9
5.6
Slave Enable (J9: EN_SLV) ...................................................................................... 9
Test Procedure .............................................................................................................. 9
6.1
Line/Load Regulation and Efficiency Measurement Procedure .............................................. 9
6.2
Loop Gain/Phase Measurement ................................................................................. 9
6.3
List of Test Points ................................................................................................ 10
6.4
Equipment Shutdown ............................................................................................ 10
Performance Data and Typical Characteristic Curves ................................................................ 10
7.1
Efficiency .......................................................................................................... 11
7.2
Load Regulation .................................................................................................. 11
7.3
Line Regulation ................................................................................................... 12
7.4
1.5-V Output Ripple .............................................................................................. 12
7.5
1.5-V Switching Node at Full Load ............................................................................. 13
7.6
1.5-V Switching Node at No Load .............................................................................. 13
7.7
Master-Slave 180° Synchronization ............................................................................ 14
7.8
1.5-V Master Turnoff During Master-Slave Synchronization ................................................ 14
7.9
1.5-V Output Transient ........................................................................................... 15
7.10 1.5-V Turnon Waveform ......................................................................................... 15
7.11 1.5-V Turnoff Waveform ......................................................................................... 16
7.12 1.5-V Hiccup OCP Waveform ................................................................................... 16
7.13 1.5-V Bode Plot ................................................................................................... 17
7.14 EVM Top Board Thermal Image ................................................................................ 17
EVM Assembly Drawings and PCB Layout ............................................................................ 18
Bill of Materials ............................................................................................................. 22
Eco-mode is a trademark of Texas Instruments.
SLUU826 – January 2012
Submit Documentation Feedback
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
1
www.ti.com
List of Figures
1
2
3
4
5
6
7
8
9
10
..........................................................................................
Tip and Barrel Measurement for Vout Ripple ...........................................................................
TPS53310EVM-755 Recommended Test Setup .......................................................................
TPS53310EVM-755 Efficiency ...........................................................................................
TPS53310EVM-755 Load Regulation ..................................................................................
TPS53310EVM-755 Line Regulation ...................................................................................
TPS53310EVM-755 Output Ripple (3.3 Vin, 1.5 V/3 A) ..............................................................
TPS53310EVM-755 Switching Node at Full Load (5 Vin, 1.5 V/3 A) ...............................................
TPS53310EVM-755 Switching Node at No Load (5 Vin, 1.5 V/0 A DE Mode)....................................
TPS53310EVM-755 Synchronization (3.3 Vin, 1.5 V/3 A, 1.2 V/3 A 180° Synchronization) ....................
TPS53310EVM-755 Schematic
5
6
7
11
11
12
12
13
13
14
11
TPS53310EVM-755 Synchronization (3.3 Vin, 1.5 V/3 A, 1.2 V/3 A 180° Synchronization, Then Turn Off
Master) ...................................................................................................................... 14
12
TPS53310EVM-755 1.5-V Output Transient (5 Vin, 1.5 V/0 A-3 A )
13
14
15
16
17
18
19
20
21
22
23
...............................................
TPS53310EVM-755 Enable Turns On Waveform (3.3 Vin, 1.5 V/3 A) .............................................
TPS53310EVM-755 Enable Turns Off Waveform (3.3 Vin, 1.5 V/3 A) .............................................
TPS53310EVM-755 Hiccup OCP Waveform (5 Vin, 1.5 V/5.5 A OCP) ............................................
TPS53310EVM-755 Bode Plot (3.3 Vin, 1.5 V/3 A)...................................................................
TPS53310EVM-755 Top-Side Thermal Image (3.3 Vin, 1.5 V/3 A, 1.2 V/3 A)....................................
TPS53310EVM-755 Top Layer Assembly Drawing, Top View ......................................................
TPS53310EVM-755 Bottom Assembly Drawing, Bottom View ......................................................
TPS53310EVM-755 Top Copper, Top View ...........................................................................
TPS53310EVM-755 Internal Layer 2, Top View ......................................................................
TPS53310EVM-755 Internal Layer 3, Top View ......................................................................
TPS53310EVM-755 Bottom Copper, Top View .......................................................................
15
15
16
16
17
17
18
19
19
20
20
21
List of Tables
2
1
TPS53310EVM-755 Electrical Performance Specifications ........................................................... 3
2
5Vin Option .................................................................................................................. 8
3
Master Mode Selection ..................................................................................................... 8
4
Slave Mode Selection ...................................................................................................... 8
5
Synchronization Selection
6
Master Enable Selection ................................................................................................... 9
7
Slave Enable Selection ..................................................................................................... 9
8
Functions of Each Test Points ........................................................................................... 10
9
Bill of Materials............................................................................................................. 22
.................................................................................................
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
8
SLUU826 – January 2012
Submit Documentation Feedback
Description
www.ti.com
1
Description
The TPS53310EVM-755 uses a regulated 3.3-V or 5-V bus to produce outputs at up to 3 A of load
current. The output is 1.5-V master and 1.2-V slave. The TPS53310EVM-755 is designed to demonstrate
the TPS53310 in a typical low-voltage application while providing test points to evaluate the performance
of the TPS53310.
1.1
Typical Applications
•
•
•
•
•
•
1.2
Servers, notebook/netbook computers
Multifunction printers (MFP)
Embedded personal computers, POS terminals
Switches, routers
Low-voltage, point-of-load converters
Any Energy Star/80Plus low-voltage rail
Features
The TPS53310EVM-755 features:
• 1.5-V master and 1.2-V slave outputs
• 3-Adc steady-state current
• 1.1-MHz switching frequency
• Hiccup overcurrent protection
• J1: selectable 3.3-V or 5-V input voltage
• J2, J7: selectable FCCM, DE, HEF mode
• J5: selectable master and slave interleaved operation
• J4, J9 for master and slave enable function
• Loop gain measurement
• Convenient test points for probing critical waveforms
• Four-layer PCB with 2 oz of copper on the outside layers
2
Electrical Performance Specifications
Table 1. TPS53310EVM-755 Electrical Performance Specifications
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
VIN input voltage range*
Vin
2.9
3.3/5
6
V
Maximum input current
Vin = 3.3 V, 1.5 V/ 3 A, 1.2 V/3 A, FCCM
2.82
A
No-load input current
Vin = 3.3 V, 1.5 V/0 A, 1.2 V/0 A, FCCM
40
mA
V
INPUT CHARACTERISTICS
OUTPUT CHARACTERISTICS
Master output voltage Vo_MST
1.485
1.5
1.515
Slave output voltage Vo_SLV
1.188
1.2
1.212
Output voltage regulation
Output voltage ripple
Line regulation
0.1
Load regulation
1.0
Vin = 3.3 V, 1.5 V/0 A-3 A, 1.2 V/0 A-3 A
Output load current
0
Output over current
V
%
%
20
mVpp
3
A
4.5
A
SYSTEMS CHARACTERISTICS
Switching frequency
Fixed
1.1
MHz
1.5-V, full-load efficiency
Vin = 3.3 V, 1.5 V/3 A
88.82
%
1.5-V, full-load efficiency
Vin = 5 V, 1.5 V/3 A
89.50
%
SLUU826 – January 2012
Submit Documentation Feedback
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
3
Electrical Performance Specifications
www.ti.com
Table 1. TPS53310EVM-755 Electrical Performance Specifications (continued)
PARAMETER
TEST CONDITIONS
1.2-V, full-load efficiency
Vin = 3.3 V, 1.2 V/3 A
86.50
1.2-V, full-load efficiency
Vin = 5 V, 1.2 V/3 A
87.32
%
25
ºC
Operating temperature
MIN
TYP
MAX
UNITS
%
Note: Jumpers set to default locations; see Section 5 of this user’s guide.
4
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
SLUU826 – January 2012
Submit Documentation Feedback
SLUU826 – January 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Mod e C onfig uratio n: Se e datashe et for de tai l
SYNC optio n
1. Ju mper shorts on J5: Master and sla ve are synchro nize d (Defau lt se tting )
2. N o Jumper sho rts on J5 : Master and sl ave are no t synch ro nize d
3
5Vin o ption
1. Ju mper sho rt across pi n1 an d pin 2 of J1 : Sets inpu t for 3.3V ope ration (Defaul t setting ).
2. Ju mper sho rt across pi n2 an d pin 3 of J1 : Sets inpu t for 5Vin o pera ti on
En abl
e
1. Ju mper shorts on J4 an d J9: D isab le the conve rte r (D efaul t setti ng )
2. N o Jumper sho rts on J4 a nd J9: Enab le th e conve rter
No t used
www.ti.com
Schematic
Schematic
Figure 1. TPS53310EVM-755 Schematic
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
5
Test Setup
4
Test Setup
4.1
Test Equipment
www.ti.com
Voltage Source VIN:
The input voltage source VIN must be a 0-V to 6-V variable dc source capable of supplying 3 Adc.
Connect Vin to J6 as shown in Figure 3.
Multimeters: V1:
Vin at TP5 (Vin_MST) and TP8 (GND)
V2: 1.5 Vout at TP7 (Vout_MST) and TP10 (GND)
V3: 1.2 Vout at TP19 (Vout_SLV) and TP21 (GND)
A1: Vin input current
Output Load:
Load1: The output load1 must be an electronic constant-resistance-mode load capable of 0 Adc to 5 Adc
at 1.5 V.
Load2: The output load2 must be an electronic constant-resistance-mode load capable of 0 Adc to 5 Adc
at 1.2 V.
Oscilloscope:
A digital or analog oscilloscope can be used to measure the output ripple. The oscilloscope must be set
for 1-MΩ impedance, 20-MHz bandwidth, ac coupling, 1-µs/division horizontal resolution, 20-mV/division
vertical resolution. Test points TP7, TP10 can be used to measure 1.5-V master output ripple voltage.
TP19 and TP21 can be used to measure 1.2-V slave output ripple voltage. Place the oscilloscope probe
tip through TP7 (TP19), and hold the ground barrel TP10 (TP21) as shown in Figure 2.
Do not use a leaded ground connection as this may induce additional noise due to the large ground loop.
Metal Ground Barrel
Probe Tip
TP7(19)
TP10(21)
Figure 2. Tip and Barrel Measurement for Vout Ripple
Recommended Wire Gauge:
1. Vin to J6: The recommended wire size is AWG 16 per input connection, with the total length of wire
less than 4 feet (2-foot input, 2-foot return).
2. J3 to LOAD1 the minimum recommended wire size is AWG 16, with the total length of wire less than 4
feet (2-foot input, 2-foot return)
3. J8 to LOAD2 the minimum recommended wire size is AWG16, with the total length of wire less than 4
feet (2-foot input, 2-foot return)
6
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
SLUU826 – January 2012
Submit Documentation Feedback
Test Setup
www.ti.com
4.2
Recommended Test Setup
V1
V2
DC
Load1
TEXAS
I NSTRUMENT S
Source
VIN
A1
V3
Load2
Figure 3. TPS53310EVM-755 Recommended Test Setup
Figure 3 is the recommended test setup to evaluate the TPS53310EVM-755. When working at an ESD
workstation, make sure that any wrist straps, bootstraps, or mats are connected referencing the user to
earth ground before handling the EVM.
Input Connections:
1. Prior to connecting the dc input source VIN, it is advisable to limit the source current from VIN to 5 A
maximum. Ensure that VIN is set initially to 0 V and connected as shown in Figure 3.
2. Connect a voltmeter V1 at TP5 (Vin_MST) and TP8 (GND) to measure input voltage.
3. Connect a current meter A1 between VIN DC source and J6.
Output Connections:
1. Connect Load1 to J3, and set Load to constant resistance mode to sink 0 Adc before Vin is applied.
2. Connect a voltmeter V2 at TP7 (Vout_MST) and TP10 (GND) to measure the 1.5-V output voltage.
3. Connect Load2 to J8, and set Load to constant resistance mode to sink 0 Adc before Vin is applied.
4. Connect a voltmeter V3 at TP19 (Vout_SLV) and TP21 (GND) to measure the 1.2-V output voltage.
SLUU826 – January 2012
Submit Documentation Feedback
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
7
Configuration
5
www.ti.com
Configuration
All jumper selections must be made prior to applying power to the EVM. Users can configure this EVM per
following configurations.
5.1
5Vin Option (J1: 5Vin Option)
The 5-V input option can be set by
J1 Default setting: 3.3Vin.
Table 2. 5Vin Option
5.2
Jumper Set to
Input Voltage
1-2 pin shorted
3.3Vin
2-3 pin shorted
5Vin
Mode Selection (J2: MST Mode)
The Master mode selection can be set by J2.
Default setting: FCCM_Mst
Table 3. Master Mode Selection
5.3
Jumper set to
Mode
Left (1-2 pin shorted)
FCCM Slave
Second (3-4 pin shorted)
DE Slave
Third (5-6 pin shorted)
HEF
Fourth (7-8 pin shorted)
Reserved
Fifth (9-10 pin shorted)
DE Master
Right(11-12 pin shorted)
FCCM Master
Mode Selection (J7: SLV Mode)
The Slave mode selection can be set by J7.
Default setting: FCCM_Slave
Table 4. Slave Mode Selection
5.4
Jumper set to
Mode
Left (1-2 pin shorted)
FCCM Slave
Second (3-4 pin shorted)
DE Slave
Third (5-6 pin shorted)
HEF
Fourth (7-8 pin shorted)
Reserved
Fifth (9-10 pin shorted)
DE Master
Right(11-12 pin shorted)
FCCM Master
Synchronization (J5: SYNC)
The synchronization for input interleaving can be set by J5.
Default setting: Jumper on J5, Master and Slave 180° Interleaved
Table 5. Synchronization Selection
8
Jumper set to
Master and Slave Synchronization
Jumper shorts on J5
Yes
No Jumper on J5
No
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
SLUU826 – January 2012
Submit Documentation Feedback
Test Procedure
www.ti.com
5.5
Master Enable (J4: EN_MST)
The Master Enable can be set by J4.
Default setting: Jumper on J4
Table 6. Master Enable Selection
5.6
Jumper set to
Enable/Disable Controller
Jumper shorts on J4
Disable 1.5-V Master output
No Jumper on J4
Enable 1.5-V Master output
Slave Enable (J9: EN_SLV)
The Slave Enable can be set by J9.
Default setting: Jumper on J9
Table 7. Slave Enable Selection
Jumper set to
Enable/Disable Controller
Jumper shorts on J9
Disable 1.2-V Master output
No Jumper on J9
Enable 1.2-V Master output
6
Test Procedure
6.1
Line/Load Regulation and Efficiency Measurement Procedure
1. Ensure that Load1 and Load2 are set to constant resistance mode and sink 0 A.
2. Ensure that all jumper configuration settings are per Section 5.
3. Ensure that jumpers short on J4, J9 before Vin is applied.
4. Increase Vin from 0 V to 3.3 V. Use V1 to measure input voltage.
5. Remove jumper from J4 to enable the master controller.
6. Vary Load1 from 0 A to 3 A; 1.5-V master output must remain in load regulation.
7. Vary Vin from 2.9 V to 3.5 V; 1.5-V master output must remain in line regulation.
8. Remove jumper from J9 to enable the slave controller.
9. Vary Load2 from 0 A to 3 A; 1.2-V slave output must remain in load regulation.
10. Vary Vin from 2.9 V to 3.5 V; 1.2-V slave output must remain in line regulation.
11. Measure the waveforms of SW_MST (TP6) and SW_SLV (TP18) to see master-slave 180°
interleaved.
12. Put jumpers on J4, J9 to disable master and slave controller.
13. Decrease Load1 and Load2 to 0 A.
14. Decrease Vin to 0 V.
6.2
Loop Gain/Phase Measurement
1.
2.
3.
4.
5.
6.
Set up the EVM as described in Section 6.1 and Figure 3. Measure 1.5-V bode plot.
Connect the isolation transformer to CHA_MST and CHB_MST.
Connect input signal CHA to TP1(CHA_MST), and connect output signal CHB to TP2 (CHB_MST).
Connect the GND lead of CHA and CHB to TP25(GND).
Inject approximately a 50-mV or less signal through the isolate transformer.
Sweep the frequency from 500 Hz to 1 MHz with a 10-Hz or lower post filter. The control loop gain and
phase margin can be measured.
7. Disconnect isolate transformer from the bode plot setup before making other measurements. (Signal
injection into feedback may interfere with accuracy of other measurement.)
SLUU826 – January 2012
Submit Documentation Feedback
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
9
Performance Data and Typical Characteristic Curves
www.ti.com
8. The loop measurement for 1.2-V slave output is the same with 1.5-V master output.
6.3
List of Test Points
Table 8. Functions of Each Test Points
(1)
6.4
Test Points
Name
Description
TP1 (1)
CHA_MST
Input A for 1.5-V loop injection
TP2
CHB_MST
Input B for 1.5-V loop injection
TP3
3.3VDD
3.3VDD
TP4
GND
Ground
TP5
Vin_MST
Input voltage for 1.5-V master
TP6
SW_MST
Switching node for 1.5-V master
TP7
Vout_MST
1.5-V output
TP8
GND
Ground
TP9
EN_MST
Enable for 1.5-V master
TP10
GND
Ground
TP11
GND
Ground
TP12
SYNC_MST
SYNC signal for 1.5-V master
TP13
PG_MST
Power Good for 1.5-V master
TP14
CHA_SLV
Input A for 1.2-V loop injection
TP15
CHB_SLV
Input B for 1.2-V loop injection
TP16
Vin_SLV
Input voltage for 1.2-V slave
TP17
GND
Ground
TP18
SW_SLV
Switching node for 1.2-V slave
TP19
Vout_SLV
1.2-V output
TP20
SYNC_SLV
SYNC signal for 1.2-V slave
TP21
GND
Ground
TP22
EN_SLV
Enable for 1.2-V slave
TP23
PG_SLV
Power Good for 1.2-V slave
TP24
GND
Ground
TP25
GND
Ground
TP26
GND
Ground
For test point locations, see Figure 3.
Equipment Shutdown
1. Shut down load.
2. Shut down Vin.
3. Shut down oscilloscope.
7
Performance Data and Typical Characteristic Curves
Figure 4 through Figure 17 present typical performance curves for TPS53310EVM-755. Jumpers set to
default locations; see Section 6.
10
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
SLUU826 – January 2012
Submit Documentation Feedback
Performance Data and Typical Characteristic Curves
www.ti.com
7.1
Efficiency
100
3.3 VI,1.2 VO
90
3.3 VI,1.5 VO
80
5 VI,1.5 VO
Efficiency - %
70
5 VI,1.2 VO
60
50
40
30
20
10
0
0.001
0.01
0.1
IO - Output Current - A
1
10
NOTE: R-C snubber to reduce switching node ringing has effect on dc-dc converter efficiency.
Figure 4. TPS53310EVM-755 Efficiency
7.2
Load Regulation
1.6
1.5V/1.2V Output Voltage - V
1.5
3.3Vin, 1.5Vout,FCCM
5Vin,1.5Vout, FCCM
3.3Vin,1.5Vout, DE
5Vin, 1.5Vout, DE
3.3Vin, 1.5Vout, HEF
5Vin, 1.5Vout, HEF
3.3Vin, 1.2Vout, FCCM
1.4
5Vin, 1.2Vout, FCCM
3.3Vin, 1.2Vout, DE
5Vin, 1.2Vout, DE
3.3Vin, 1.2Vout, HEF
5Vin, 1.2Vout, HEF
1.3
1.2
1.1
1
0
0.5
1
1.5
2
2.5
3
IO - Output Current - A
Figure 5. TPS53310EVM-755 Load Regulation
SLUU826 – January 2012
Submit Documentation Feedback
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
11
Performance Data and Typical Characteristic Curves
7.3
www.ti.com
Line Regulation
1.6
1.5V/1.2V Output Voltage - V
1.5
1.5Vout/0A, FCCM
1.5Vout/3A, FCCM
1.5Vout/0A, DE
1.5Vout/3A, DE
1.5Vout/0A, HEF
1.5Vout/3A, HEF
1.4
1.2Vout/0A, FCCM
1.2Vout/3A, FCCM
1.2Vout/0A, DE
1.2Vout/3A, DE
1.2Vout/0A, HEF
1.2Vout/3A, HEF
1.3
1.2
1.1
1
2.9
3.4
3.9
4.4
4.9
VI - Input Voltage - V
5.4
5.9
6.4
Figure 6. TPS53310EVM-755 Line Regulation
7.4
1.5-V Output Ripple
TPS53310EVM-755
Output Ripple
Test condition: 3.3Vin, 1.5V/3A, FCCM
CH1: 1.5V_MST Output Ripple
Figure 7. TPS53310EVM-755 Output Ripple (3.3 Vin, 1.5 V/3 A)
12
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
SLUU826 – January 2012
Submit Documentation Feedback
Performance Data and Typical Characteristic Curves
www.ti.com
7.5
1.5-V Switching Node at Full Load
TPS53310EVM-755
1.5Vout Switching Node
Test condition: 5Vin, 1.5V/3A, FCCM
CH2: SW_MST
Figure 8. TPS53310EVM-755 Switching Node at Full Load (5 Vin, 1.5 V/3 A)
7.6
1.5-V Switching Node at No Load
TPS53310EVM-755
1.5Vout Switching Node
Test condition: 5Vin, 1.5V/0A, DE
CH2: SW_MST
Figure 9. TPS53310EVM-755 Switching Node at No Load (5 Vin, 1.5 V/0 A DE Mode)
SLUU826 – January 2012
Submit Documentation Feedback
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
13
Performance Data and Typical Characteristic Curves
7.7
www.ti.com
Master-Slave 180° Synchronization
TPS53310EVM-755
Master-Slave Synchronization
Test condition: 3.3Vin, 1.5V/3A, FCCM
CH1: SW_MST
CH2: SW_SLV
Figure 10. TPS53310EVM-755 Synchronization
(3.3 Vin, 1.5 V/3 A, 1.2 V/3 A 180° Synchronization)
7.8
1.5-V Master Turnoff During Master-Slave Synchronization
TPS53310EVM-755
Master-Slave Synchronization
Test condition: 3.3Vin, 1.5V/3A, FCCM
1.5V Master Enable Turn off
CH1: EN_MST
CH2: SW_MST
CH3: EN_SLY
CH4: SW_SLV
Figure 11. TPS53310EVM-755 Synchronization
(3.3 Vin, 1.5 V/3 A, 1.2 V/3 A 180° Synchronization, Then Turn Off Master)
14
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
SLUU826 – January 2012
Submit Documentation Feedback
Performance Data and Typical Characteristic Curves
www.ti.com
7.9
1.5-V Output Transient
TPS53310EVM-755
Transient Response
Test condition: 5Vin, 1.5V/0A-3A, FCCM
CH1: 1.5Voutput
CH2: SW_MST
CH3: 1.5Voutput current 0A-3A
Figure 12. TPS53310EVM-755 1.5-V Output Transient (5 Vin, 1.5 V/0 A-3 A )
7.10 1.5-V Turnon Waveform
TPS53310EVM-755
1.5V Enable Start up
Test condition: 3.3Vin, 1.5V/3A, FCCM
CH1: EN_MST
CH2: 1.5Voutput
CH3: SW_MST
CH3: PG_MST
Figure 13. TPS53310EVM-755 Enable Turns On Waveform
(3.3 Vin, 1.5 V/3 A)
SLUU826 – January 2012
Submit Documentation Feedback
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
15
Performance Data and Typical Characteristic Curves
www.ti.com
7.11 1.5-V Turnoff Waveform
TPS53310EVM-755
1.5V Enable Turn off
Test condition: 3.3Vin, 1.5V/3A, FCCM
CH1: EN_MST
CH2: 1.5Voutput
CH3: SW_MST
CH4: PG_MST
Figure 14. TPS53310EVM-755 Enable Turns Off Waveform
(3.3 Vin, 1.5 V/3 A)
7.12 1.5-V Hiccup OCP Waveform
TPS53310EVM-755
1.5Vout Hiccup OCP
Test condition: 5Vin, 1.5V/5.5A, OCP, FCCM
CH1: 1.5Vout
CH2: SW_MST
CH3: PG_MST
Figure 15. TPS53310EVM-755 Hiccup OCP Waveform
(5 Vin, 1.5 V/5.5 A OCP)
16
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
SLUU826 – January 2012
Submit Documentation Feedback
Performance Data and Typical Characteristic Curves
www.ti.com
7.13 1.5-V Bode Plot
Figure 16. TPS53310EVM-755 Bode Plot (3.3 Vin, 1.5 V/3 A)
7.14 EVM Top Board Thermal Image
Figure 17. TPS53310EVM-755 Top-Side Thermal Image
(3.3 Vin, 1.5 V/3 A, 1.2 V/3 A)
SLUU826 – January 2012
Submit Documentation Feedback
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
17
EVM Assembly Drawings and PCB Layout
8
www.ti.com
EVM Assembly Drawings and PCB Layout
The following figures (Figure 18 through Figure 23) show the design of the TPS53310EVM-755
printed-circuit board. The EVM has been designed using a four-layer circuit board with 2 oz of copper on
the outside layers.
TEXAS
INSTRUMENTS
Figure 18. TPS53310EVM-755 Top Layer Assembly Drawing, Top View
18
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
SLUU826 – January 2012
Submit Documentation Feedback
EVM Assembly Drawings and PCB Layout
www.ti.com
Figure 19. TPS53310EVM-755 Bottom Assembly Drawing, Bottom View
Figure 20. TPS53310EVM-755 Top Copper, Top View
SLUU826 – January 2012
Submit Documentation Feedback
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
19
EVM Assembly Drawings and PCB Layout
www.ti.com
Figure 21. TPS53310EVM-755 Internal Layer 2, Top View
Figure 22. TPS53310EVM-755 Internal Layer 3, Top View
20
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
SLUU826 – January 2012
Submit Documentation Feedback
EVM Assembly Drawings and PCB Layout
www.ti.com
Figure 23. TPS53310EVM-755 Bottom Copper, Top View
SLUU826 – January 2012
Submit Documentation Feedback
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
21
Bill of Materials
9
www.ti.com
Bill of Materials
Table 9 shows the EVM major components list according to the schematic shown in Figure 1..
Table 9. Bill of Materials
QTY
22
RefDes
Description
MFR
Part No.
4
C1, C2, C15, C16
Capacitor, Ceramic, 2.2nF, 50V, X7R, 10%, 0603
STD
STD
2
C13, C27
Capacitor, Ceramic, 820pF, 50V, X7R, 10%, 0603
STD
STD
6
C6, C10, C11,C20, Capacitor, Ceramic, 22µF, 16V, X5R, 10%, 1210
C23, C24
STD
STD
2
C3, C17
STD
STD
4
C4, C18, C29, C30 Capacitor, Ceramic, 10µF, 10V, X5R, 10%, 0805
STD
STD
6
C7, C8, C12, C21,
C22, C26
Capacitor, Ceramic, 0.1µF, 25V, X7R, 10%, 0603
STD
STD
2
L1, L2
Inductor, SMT, 1uH, 5.6A, 5.4mohm, 5.0x5.0mm
ICE
components
IN06142
5
R1, R5, R13, R18,
R19
Resistor, Chip, 4.02k, 1/16W, 1%, 0603
STD
STD
2
R10, R22
Resistor, Chip, 3.01, 1/10W, 5%, 0805
STD
STD
2
R11, R23
Resistor, Chip, 0, 1/16W, 5%, 0603
STD
STD
2
R12, R24
Resistor, Chip, 10.0k, 1/16W, 1%, 0603
STD
STD
2
R2, R14
Resistor, Chip, 10, 1/16W, 1%, 0603
STD
STD
2
R25, R26
Resistor, Chip, 0, 1W, 5%, 2512
STD
STD
2
R3, R16
Resistor, Chip, 20, 1/16W, 1%, 0603
STD
STD
2
R4, R15
Resistor, Chip, 24.3k, 1/16W, 1%,0603
STD
STD
2
R6, R17
Resistor, Chip, 57.6k, 1/16W, 1%,0603
STD
STD
1
R7
Resistor, Chip, 2.67k, 1/16W, 1%,0603
STD
STD
2
R8, R20
Resistor, Chip, 105k, 1/16W, 1%, 0603
STD
STD
2
R9, R21
Resistor, Chip, 174k, 1/16W, 1%, 0603
STD
STD
1
U1
IC, 150mA, Low Iq, Wide bandwidth, LDO Linear regulator, SC70
TI
TPS71733DCKR
1
U2, U3
IC, 3A Step-down regulator with integrated switcher, QFN-16
TI
TPS53310RGT
Capacitor, Ceramic, 100pF, 50V, C0G, 10%, 0603
Using the TPS53310EVM-755, A 3-A Eco-mode™ Integrated Switcher With
Master-Slave
Copyright © 2012, Texas Instruments Incorporated
SLUU826 – January 2012
Submit Documentation Feedback
Evaluation Board/Kit Important Notice
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION
PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the
product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are
not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations,
including product safety and environmental measures typically found in end products that incorporate such semiconductor
components or circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives regarding
electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the
technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30
days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY
SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all
claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to
take any and all appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER
FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of
patents or services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the
product. This notice contains important safety information about temperatures and voltages. For additional information on TI’s
environmental and/or safety programs, please contact the TI application engineer or visit www.ti.com/esh.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION
PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and
can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15
of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this
equipment in other environments may cause interference with radio communications, in which case the user at his own expense
will be required to take whatever measures may be required to correct this interference.
EVM Warnings and Restrictions
It is important to operate this EVM within the input voltage range of 2.9 V to 6 V and the output voltage range of 0 V to 5 V.
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are
questions concerning the input range, please contact a TI field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the
EVM. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load
specification, please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than 40°C. The EVM is designed to
operate properly with certain components above 40°C as long as the input and output ranges are maintained. These components
include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of
devices can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes near
these devices during operation, please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
【Important Notice for Users of this Product in Japan】
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even
if the EVM should fail to perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
