Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
TPS54233 2A, 28V Input, Step Down DC/DC Converter With Eco-mode™
1 Features
3 Description
•
•
•
The TPS54233 is a 28 V, 2 A non-synchronous buck
converter that integrates a low RDS(on) high side
MOSFET. To increase efficiency at light loads, a
pulse skipping Eco-mode™ feature is automatically
activated. Furthermore, the 1 μA shutdown supply
current allows the device to be used in battery
powered applications. Current mode control with
internal slope compensation simplifies the external
compensation calculations and reduces component
count while allowing the use of ceramic output
capacitors. A resistor divider programs the Hysteresis
of the input under-voltage lockout. An overvoltage
transient protection circuit limits voltage overshoots
during startup and transient conditions. A cycle by
cycle current limit scheme, frequency fold back and
thermal shutdown protect the device and the load in
the event of an overload condition. The TPS54233 is
available in an 8-pin SOIC package that has been
internally optimized to improve thermal performance.
1
•
•
•
•
•
•
•
•
•
3.5 V to 28 V Input Voltage Range
Adjustable Output Voltage Down to 0.8 V
Integrated 80 mΩ High Side MOSFET Supports
up to 2A Continuous Output Current
High Efficiency at Light Loads with a Pulse
Skipping Eco-mode™
Fixed 300 kHz Switching Frequency
Typical 1 μA Shutdown Quiescent Current
Adjustable Slow Start Limits Inrush Currents
Programmable UVLO Threshold
Overvoltage Transient Protection
Cycle by Cycle Current Limit, Frequency Fold
Back and Thermal Shutdown Protection
Available in Easy-to-Use SOIC8 Package
Supported by WEBENCH® Software Tool
(www.TI.com/WEBENCH)
Device Information(1)
2 Applications
•
•
•
PART NUMBER
Consumer Applications such as Set-Top Boxes,
CPE Equipment, LCD Displays, Peripherals, and
Battery Chargers
Industrial and Car Audio Power Supplies
5V, 12V and 24V Distributed Power Systems
TPS54233
PACKAGE
SOIC (8)
BODY SIZE (NOM)
4.90 mm x 3.90 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
4 Simplified Schematic
Ren1
EN
VIN
Ren2
Efficiency
VIN
CI
100
TPS54233
VO = 3.3 V
V = 12 V
VIN = 8 V IN
VIN = 15 V
95
CBOOT
BOOT
90
VOUT
PH
SS
COMP
D1
CO
R5
C6
CSS C7
R3
VSENSE
GND
Efficiency - %
LO
85
VIN = 18 V
80
75
70
R6
65
60
0
0.25 0.5 0.75 1 1.25 1.5 1.75
IO - Output Current - A
2
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Schematic.............................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
4
7.1
7.2
7.3
7.4
7.5
7.6
7.7
4
4
4
4
5
5
6
Absolute Maximum Ratings .....................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Switching Characteristics ..........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 8
8.1 Overview ................................................................... 8
8.2 Functional Block Diagram ......................................... 8
8.3 Feature Description................................................... 9
8.4 Device Functional Modes........................................ 11
9
Application and Implementation ........................ 12
9.1 Application Information............................................ 12
9.2 Typical Application ................................................. 12
10 Power Supply Recommendations ..................... 22
11 Layout................................................................... 22
11.1
11.2
11.3
11.4
Layout Guidelines .................................................
Layout Example ....................................................
Estimated Circuit Area ..........................................
Electromagnetic Interference (EMI)
Considerations .........................................................
22
22
23
23
12 Device and Documentation Support ................. 24
12.1
12.2
12.3
12.4
Device Support......................................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
24
24
24
24
13 Mechanical, Packaging, and Orderable
Information ........................................................... 24
5 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (February 2011) to Revision C
Page
•
Removed Swift™ from the data sheet title ............................................................................................................................. 1
•
Added ESD Rating table, Thermal Information table, Feature Description section, Device Functional Modes,
Application and Implementation section, Power Supply Recommendations section, Device and Documentation
Support section, and Mechanical, Packaging sections. ........................................................................................................ 1
•
Deleted Features Item: For SWIFT™ Documentation, See the TI Website at www.ti.com/swift........................................... 1
•
Changed Features item: Supported by SwitcherPro™ To: Supported by WEBENCH®........................................................ 1
•
Changed RO1 To: R5, RO2 To R6, C1 To C6, and C2 To C7 in the Simplified Schematic ..................................................... 1
•
Changed SwitcherPro™ Software tool To: WEBENCH Software tool in the Current Mode Compensation Design
section .................................................................................................................................................................................. 10
•
Changed RO1 To: R5, RO2 To R6, C1 To C6, and C2 To C7 in the Table 1 ........................................................................ 10
•
Changed the Output Voltage Set Point section. Updated the paragraph following Equation 5. .......................................... 13
Changes from Revision A (March 2010) to Revision B
•
Page
Figure 14, Changed VIN = 18 V on the top (blue) curve To: VIN = 8 V ................................................................................. 20
Changes from Original (October 2008) to Revision A
Page
•
Changed the Absolute Maximum Ratings (1) table, Input Voltage - EN pin max value From: 5V to 6V ................................. 4
•
Added A table to the Description - with text "For additional design needs, see.." ............................................................... 12
2
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
6 Pin Configuration and Functions
D Package
Top View
BOOT
1
8
PH
VIN
2
7
GND
EN
3
6
COMP
SS
4
5
VSENSE
Pin Functions
PIN
DESCRIPTION
NAME
NO.
BOOT
1
A 0.1 μF bootstrap capacitor is required between BOOT and PH. If the voltage on this capacitor falls below the
minimum requirement, the high-side MOSFET is forced to switch off until the capacitor is refreshed.
VIN
2
Input supply voltage, 3.5 V to 28 V.
EN
3
Enable pin. Pull below 1.25V to disable. Float to enable. Programming the input undervoltage lockout with two
resistors is recommended.
SS
4
Slow start pin. An external capacitor connected to this pin sets the output rise time.
VSENSE
5
Inverting node of the gm error amplifier.
COMP
6
Error amplifier output, and input to the PWM comparator. Connect frequency compensation components to this pin.
GND
7
Ground.
PH
8
The source of the internal high-side power MOSFET.
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
3
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VIN
–0.3
30
EN
–0.3
6
BOOT
Input Voltage
38
VSENSE
–0.3
3
COMP
–0.3
3
SS
–0.3
3
BOOT-PH
Output Voltage
Sink Current
V
8
PH
Source Current
UNIT
–0.6
30
V
PH (10 ns transient from ground to negative peak)
–5
EN
100
μA
BOOT
100
mA
VSENSE
10
μA
PH
6
A
VIN
6
A
COMP
100
SS
200
μA
Operating Junction Temperature
–40
150
°C
Storage Temperature
–65
150
°C
(1)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 ESD Ratings
VALUE
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
V(ESD)
(1)
(2)
Electrostatic discharge
(1)
UNIT
±2000
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
V
±500
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
TYP
MAX
UNIT
Operating Input Voltage on (VIN pin)
3.5
28
V
Operating junction temperature, TJ
–40
150
°C
7.4 Thermal Information
THERMAL METRIC (1)
D
8 PINS
RθJA
Junction-to-ambient thermal resistance
116.7
RθJC(top)
Junction-to-case (top) thermal resistance
62.4
RθJB
Junction-to-board thermal resistance
57.0
ψJT
Junction-to-top characterization parameter
14.5
ψJB
Junction-to-board characterization parameter
56.5
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
(1)
4
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
7.5 Electrical Characteristics
TJ = –40°C to 150°C, VIN = 3.5V to 28V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY VOLTAGE (VIN PIN)
Internal undervoltage lockout threshold
Rising and Falling
Shutdown supply current
EN = 0V, VIN = 12V, –40°C to 85°C
3.5
V
1
4
μA
Operating – non switching supply current
VSENSE = 0.85 V
75
110
μA
Enable threshold
Rising and Falling
1.25
1.35
Input current
Enable threshold – 50 mV
-1
μA
Input current
Enable threshold + 50 mV
-4
μA
ENABLE AND UVLO (EN PIN)
V
VOLTAGE REFERENCE
Voltage reference
0.772
0.8
0.828
BOOT-PH = 3 V, VIN = 3.5 V
115
200
BOOT-PH = 6 V, VIN = 12 V
80
150
V
HIGH-SIDE MOSFET
On resistance
mΩ
ERROR AMPLIFIER
Error amplifier transconductance (gm)
–2 μA < I(COMP) < 2 μA, V(COMP) = 1 V
Error amplifier DC gain (1)
VSENSE = 0.8 V
800
μmhos
V/V
Error amplifier unity gain bandwidth (1)
5 pF capacitance from COMP to GND pins
2.7
MHz
Error amplifier source/sink current
V(COMP) = 1 V, 100 mV overdrive
±7
μA
Switch current to COMP transconductance
VIN = 12 V
9
A/V
100
mA
3.5
A
165
°C
92
PULSE SKIPPING Eco-mode™
Pulse skipping Eco-mode™ switch current threshold
CURRENT LIMIT
Current limit threshold
VIN = 12 V
2.3
THERMAL SHUTDOWN
Thermal Shutdown
SLOW START (SS PIN)
Charge current
V(SS) = 0.4 V
2
μA
SS to VSENSE matching
V(SS) = 0.4 V
10
mV
(1)
Specified by design
7.6 Switching Characteristics
TJ = –40°C to 150°C, VIN = 3.5 to 28 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
210
300
390
kHz
105
130
ns
SWITCHING FREQUENCY
Device switching frequency
VIN = 12 V
Minimum controllable on time
VIN = 12 V, 25°C
Maximum controllable duty ratio
(1)
(1)
BOOT-PH = 6 V
90%
93%
Specified by design.
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
5
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
7.7 Typical Characteristics
4
110
VIN = 12 V
105
TJ = 150°C
Isd - Shutdown Current - mA
Rdson - On Resistance - mW
100
95
90
85
80
75
3
TJ = -40°C
2
TJ = 25°C
1
70
65
60
-50
0
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
3
150
13
18
VI - Input Voltage - V
23
28
Figure 2. Shutdown Quiescent Current vs Input Voltage
Figure 1. On Resistance vs Junction Temperature
310
0.8240
VIN = 12 V
0.8180
Vref - Voltage Reference - V
fsw - Oscillator Frequency - kHz
8
305
300
295
0.8120
0.8060
0.8000
0.7940
0.7880
0.7820
290
-50
-25
0
25
50
75
100
125
0.7760
-50
150
-25
0
125
150
Figure 3. Switching Frequency vs Junction Temperature
Figure 4. Voltage Reference vs Junction Temperature
4
VIN = 12 V
VIN = 12 V
130
120
110
100
-50
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
Figure 5. Minimum Controllable On Time vs
Junction Temperature
6
25
50
75
100
TJ - Junction Temperature - °C
140
Minimum Controllable Duty Ratio - %
Tonmin - Minimum Controllable On Time - ns
TJ - Junction Temperature - °C
150
3.75
3.50
3.25
3
-50
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
150
Figure 6. Minimum Controllable Duty Ratio vs
Junction Temperature
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
Typical Characteristics (continued)
4
Current Limit Threshold - A
ISS - Slow Start Charge Current - mA
2.10
2
TJ = -40°C
3.5
TJ = 150°C
1.90
-50
3
TJ - Junction Temperature - °C
13
18
VI - Input Voltage - V
Figure 7. SS Charge Current vs Junction Temperature
Figure 8. Current Limit Threshold vs Input Voltage
-25
0
25
50
75
100
125
3
150
30
8
23
28
150
20
TJ - Junction Temperature - °C
25
VO - Output Voltage - V
TJ = 25°C
IO = 1 A
15
IO = 2 A
10
125
100
75
50
5
0
3
8
13
18
VI - Input Voltage - V
23
28
25
0
0.2
0.4
0.6
0.8
1
1.2
PD - Power Dissipation - W
Figure 9. Typical Maximum Output Voltage vs
Input Voltage
Figure 10. Maximum Power Dissipation vs
Junction Temperature
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
7
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
8 Detailed Description
8.1 Overview
The TPS54233 is a 28 V, 2 A, step-down (buck) converter with an integrated high-side n-channel MOSFET. To
improve performance during line and load transients, the device implements a constant frequency, current mode
control which reduces output capacitance and simplifies external frequency compensation design. The
TPS54233 has a pre-set switching frequency of 300 kHz.
The TPS54233 needs a minimum input voltage of 3.5 V to operate normally. The EN pin has an internal pull-up
current source that can be used to adjust the input voltage under-voltage lockout (UVLO) with two external
resistors. In addition, the pull-up current provides a default condition when the EN pin is floating for the device to
operate. The operating current is 75 μA typically when not switching and under no load. When the device is
disabled, the supply current is 1 μA typically.
The integrated 80 mΩ high-side MOSFET allows for high efficiency power supply designs with continuous output
currents up to 2 A.
The TPS54233 reduces the external component count by integrating the boot recharge diode. The bias voltage
for the integrated high-side MOSFET is supplied by an external capacitor on the BOOT to PH pin. The boot
capacitor voltage is monitored by an UVLO circuit and will turn the high-side MOSFET off when the voltage falls
below a preset threshold of 2.1 V typically. The output voltage can be stepped down to as low as the reference
voltage.
By adding an external capacitor, the slow start time of the TPS54233 can be adjustable which enables flexible
output filter selection.
To improve the efficiency at light load conditions, the TPS54233 enters a special pulse skipping Eco-modeTM
when the peak inductor current drops below 100 mA typically.
The frequency foldback reduces the switching frequency during startup and over current conditions to help
control the inductor current. The thermal shut down gives the additional protection under fault conditions.
8.2 Functional Block Diagram
EN
VIN
165 C
Thermal
Shutdown
1 mA
3 mA
Shutdown
Shutdown
Logic
1.25 V
Enable
Threshold
Enable
Comparator
Boot
Charge
™
ECO-MODE
Minimum Clamp
Boot
UVLO
BOOT
2.1V
Error
Amplifier
VSENSE
2 mA
PWM
Comparator
Gate
Drive
Logic
gm = 92 mA/V
DC gain = 800 V/V
BW = 2.7 MHz
Voltage
Reference
SS
2 kW
0.8 V
S
Shutdown
PWM
Latch
9 A/V
Current
Sense
R
80 mW
Q
S
Slope
Compensation
PH
Discharge
Logic
VSENSE
Frequency
Shift
Oscillator
GND
COMP
Maximum
Clamp
8
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
8.3 Feature Description
8.3.1 Fixed Frequency PWM Control
The TPS54233 uses a fixed frequency, peak current mode control. The internal switching frequency of the
TPS54233 is fixed at 300kHz.
8.3.2 Voltage Reference (Vref)
The voltage reference system produces a ±2% initial accuracy voltage reference (±3.5% over temperature) by
scaling the output of a temperature stable bandgap circuit. The typical voltage reference is designed at 0.8V.
8.3.3 Bootstrap Voltage (BOOT)
The TPS54233 has an integrated boot regulator and requires a 0.1 μF ceramic capacitor between the BOOT and
PH pin to provide the gate drive voltage for the high-side MOSFET. A ceramic capacitor with an X7R or X5R
grade dielectric is recommended because of the stable characteristics over temperature and voltage. To improve
drop out, the TPS54233 is designed to operate at 100% duty cycle as long as the BOOT to PH pin voltage is
greater than 2.1V typically.
8.3.4 Enable and Adjustable Input Under-Voltage Lockout (VIN UVLO)
The EN pin has an internal pull-up current source that provides the default condition of the TPS54233 operating
when the EN pin floats.
The TPS54233 is disabled when the VIN pin voltage falls below internal VIN UVLO threshold. It is recommended
to use an external VIN UVLO to add Hysteresis unless VIN is greater than (VOUT + 2V). To adjust the VIN UVLO
with Hysteresis, use the external circuitry connected to the EN pin as shown in Figure 11. Once the EN pin
voltage exceeds 1.25V , an additional 3 μA of hysteresis is added. Use Equation 1 and Equation 2 to calculate
the resistor values needed for the desired VIN UVLO threshold voltages. The VSTART is the input start threshold
voltage, the VSTOP is the input stop threshold voltage and the VEN is the enable threshold voltage of 1.25 V. The
VSTOP should always be greater than 3.5 V.
VIN
Ren1
1 mA
3 mA
+
EN
Ren2
1.25 V
-
Figure 11. Adjustable Input Undervoltage Lockout
Ren1 =
Ren2 =
VSTART - VSTOP
3 mA
(1)
VEN
VSTART - VEN
+ 1 mA
Ren1
(2)
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
9
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
Feature Description (continued)
8.3.5 Programmable Slow Start Using SS PIN
It is recommended to program the slow start time externally because no slow start time is implemented internally.
The TPS54233 effectively uses the lower voltage of the internal voltage reference or the SS pin voltage as the
power supply’s reference voltage fed into the error amplifier and will regulate the output accordingly. A capacitor
(CSS) on the SS pin to ground implements a slow start time. The TPS54233 has an internal pull-up current
source of 2 μA that charges the external slow start capacitor. The equation for the slow start time (10% to 90%)
is shown in Equation 3 . The Vref is 0.8 V and the ISS current is 2 μA.
CSS (nF ) ´ Vref (V )
TSS (ms ) =
ISS (mA )
(3)
The slow start time should be set between 1ms to 10ms to ensure good start-up behavior. The slow start
capacitor should be no more than 27 nF.
If during normal operation, the input voltage drops below the VIN UVLO threshold, or the EN pin is pulled below
1.25 V, or a thermal shutdown event occurs, the TPS54233 stops switching.
8.3.6 Error Amplifier
The TPS54233 has a transconductance amplifier for the error amplifier. The error amplifier compares the
VSENSE voltage to the internal effective voltage reference presented at the input of the error amplifier. The
transconductance of the error amplifier is 92 μA/V during normal operation. Frequency compensation
components are connected between the COMP pin and ground.
8.3.7 Slope Compensation
To prevent the sub-harmonic oscillations when operating the device at duty cycles greater than 50%, the
TPS54233 adds a built-in slope compensation which is a compensating ramp to the switch current signal.
8.3.8 Current Mode Compensation Design
To simplify design efforts using the TPS54233, the typical designs for common applications are listed in Table 1.
For designs using ceramic output capacitors, proper derating of ceramic output capacitance is recommended
when doing the stability analysis. This is because the actual ceramic capacitance drops considerably from the
nominal value when the applied voltage increases. See the Detailed Design Procedure section for the detailed
guidelines or use the WEBENCH Software tool (www.TI.com/WEBENCH).
Table 1. Typical Designs (Refer to Section 4: Simplified Schematic
10
VIN
(V)
VOUT
(V)
Fsw
(kHz)
LO
(μH)
CO
R5
(kΩ)
R6
(kΩ)
C7
(pF)
C6
(pF)
R3
(kΩ)
12
5
300
22
Ceramic 47 μF
10
1.91
68
1800
21
12
3.3
300
15
Ceramic 47μF
10.2
3.24
47
4700
21
12
1.8
300
10
Ceramic 100 μF x 2
10
8.06
100
4700
21
12
0.9
300
6.8
Ceramic 100 μFx2
10
80.6
100
4700
21
12
5
300
22
Aluminum 330 μF/160 mΩ
10
1.91
56
220
40.2
12
3.3
300
15
Aluminum 470 μF/160 mΩ
10.2
3.24
220
220
30.9
12
1.8
300
10
SP 220 μF/12 mΩ
10
8.06
100
4700
40.2
12
0.9
300
6.8
SP 220 μF/12 mΩ
10
80.6
100
1800
21
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
8.3.9 Overcurrent Protection and Frequency Shift
The TPS54233 implements current mode control that uses the COMP pin voltage to turn off the high-side
MOSFET on a cycle by cycle basis. Every cycle the switch current and the COMP pin voltage are compared;
when the peak inductor current intersects the COMP pin voltage, the high-side switch is turned off. During
overcurrent conditions that pull the output voltage low, the error amplifier responds by driving the COMP pin high,
causing the switch current to increase. The COMP pin has a maximum clamp internally, which limit the output
current.
The TPS54233 provides robust protection during short circuits. There is potential for overcurrent runaway in the
output inductor during a short circuit at the output. The TPS54233 solves this issue by increasing the off time
during short circuit conditions by lowering the switching frequency. The switching frequency is divided by 8, 4, 2,
and 1 as the voltage ramps from 0 V to 0.8 V on VSENSE pin. The relationship between the switching frequency
and the VSENSE pin voltage is shown in Table 2.
Table 2. Switching Frequency Conditions
SWITCHING FREQUENCY
VSENSE PIN VOLTAGE
300 kHz
VSENSE ≥ 0.6 V
300 kHz / 2
0.6 V > VSENSE ≥ 0.4 V
300 kHz / 4
0.4 V > VSENSE ≥ 0.2 V
300 kHz / 8
0.2 V > VSENSE
8.3.10 Overvoltage Transient Protection
The TPS54233 incorporates an overvoltage transient protection (OVTP) circuit to minimize output voltage
overshoot when recovering from output fault conditions or strong unload transients. The OVTP circuit includes an
overvoltage comparator to compare the VSENSE pin voltage and internal thresholds. When the VSENSE pin
voltage goes above 109% × Vref, the high-side MOSFET will be forced off. When the VSENSE pin voltage falls
below 107% × Vref, the high-side MOSFET will be enabled again.
8.3.11 Thermal Shutdown
The device implements an internal thermal shutdown to protect itself if the junction temperature exceeds 165°C.
The thermal shutdown forces the device to stop switching when the junction temperature exceeds the thermal
trip threshold. Once the die temperature decreases below 165°C, the device reinitiates the power up sequence.
8.4 Device Functional Modes
8.4.1 Eco-modeTM
The TPS54233 is designed to operate in pulse skipping Eco-modeTM at light load currents to boost light load
efficiency. When the peak inductor current is lower than 100 mA typically, the COMP pin voltage falls to 0.5V
typically and the device enters Eco-mode™. When the device is in Eco-mode™, the COMP pin voltage is
clamped at 0.5V internally which prevents the high side integrated MOSFET from switching. The peak inductor
current must rise above 100mA for the COMP pin voltage to rise above 0.5V and exit Eco-mode™. Since the
integrated current comparator catches the peak inductor current only, the average load current entering Ecomode™ varies with the applications and external output filters.
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
11
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The TPS54233 device is typically used as a step-down converter, which converts a voltage from 3.5 V to 28 V to
a lower voltage. WEBENCH software is available to aid in the design and analysis of circuits.
For additional design needs, see the following devices.
TPS54231
TPS54232
TPS54233
TPS54331
IO(Max)
2A
2A
2A
3A
TPS54332
3.5A
Input Voltage Range
3.5V - 28V
3.5V - 28V
3.5V - 28V
3.5V - 28V
3.5V - 28V
Switching Freq. (Typ)
570kHz
1000kHz
285kHz
570kHz
1000kHz
Switch Current Limit (Min)
2.3A
2.3A
2.3A
3.5A
4.2A
Pin/Package
8SOIC
8SOIC
8SOIC
8SOIC
8SO PowerPAD™
9.2 Typical Application
Vout 3.3 V,
Iout Max 2 A
L1
15 mH
D1
C4
0.1 mF
+
B230A
C9
470 mF
Vin 8 - 18 V
C1
10 mF
R1
332 kW
C6
220 pF
C5
0.015 mF
R2
68.1 kW
R3
30.9 kW
R5
10.2 kW
R6
3.24 kW
C7
220 pF
Figure 12. Typical Application Schematic
9.2.1 Design Requirements
For this design example, use the input parameters in Table 3.
Table 3. Design Parameters
12
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage range
8 V to 18 V
Output voltage
3.3 V
Input ripple voltage
300 mV
Output ripple voltage
100 mV
Output current rating
2A
Operating Frequency
300 kHz
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
9.2.2 Detailed Design Procedure
The following design procedure can be used to select component values for the TPS54233. Alternately, the
WEBENCH Software can be used to generate a complete design. The WEBENCH Software uses an iterative
design procedure and accesses a comprehensive database of components when generating a design. This
section presents a simplified discussion of the design process.
9.2.2.1 Switching Frequency
The switching frequency for the TPS54233 is fixed at 300 kHz.
9.2.2.2 Output Voltage Set Point
The output voltage of the TPS54233 is externally adjustable using a resistor divider network. In the application
circuit of Figure 12, this divider network is comprised of R5 and R6. The relationship of the output voltage to the
resistor divider is given by Equation 4 and Equation 5:
R5 ´ VREF
R6 =
VOUT - VREF
(4)
é R5 ù
VOUT = VREF ´ ê
+1ú
ë R6 û
(5)
Choose R5 to be approximately 10 kΩ. Slightly increasing or decreasing R5 can result in closer output voltage
matching when using standard value resistors. In this design, R5 = 10.2 kΩ and R6 = 3.24 kΩ, resulting in a
3.31 V output voltage.
9.2.2.3 Input Capacitors
The TPS54233 requires an input decoupling capacitor and depending on the application, a bulk input capacitor.
The typical recommended value for the decoupling capacitor is 10 μF. A high-quality ceramic type X5R or X7R is
recommended. The voltage rating should be greater than the maximum input voltage. A smaller value may be
used as long as all other requirements are met; however 10 μF has been shown to work well in a wide variety of
circuits. Additionally, some bulk capacitance may be needed, especially if the TPS54233 circuit is not located
within about 2 inches from the input voltage source. The value for this capacitor is not critical but should be rated
to handle the maximum input voltage including ripple voltage, and should filter the output so that input ripple
voltage is acceptable. For this design two 4.7 μF capacitors are used for the input decoupling capacitor. They are
X7R dielectric rated for 50 V. The equivalent series resistance (ESR) is approximately 2 mΩ, and the current
rating is 3 A. Additionally, a small 0.01 μF capacitor is included for high frequency filtering.
This input ripple voltage can be approximated by Equation 6
IOUT(MAX) ´ 0.25
DVIN =
+ IOUT(MAX) ´ ESRMAX
CBULK ´ fSW
(
)
(6)
Where IOUT(MAX) is the maximum load current, fSW is the switching frequency, CBULK is the bulk capacitor value
and ESRMAX is the maximum series resistance of the bulk capacitor.
The maximum RMS ripple current also needs to be checked. For worst case conditions, this can be
approximated by Equation 7
IOUT(MAX)
ICIN =
2
(7)
In this case, the input ripple voltage would be 143 mV and the RMS ripple current would be 1.5 A. It is also
important to note that the actual input voltage ripple will be greatly affected by parasitics associated with the
layout and the output impedance of the voltage source. The actual input voltage ripple for this circuit is shown in
Design Parameters and is larger than the calculated value. This measured value is still below the specified input
limit of 300 mV. The maximum voltage across the input capacitors would be VIN max plus ΔVIN/2. The chosen
bulk and bypass capacitors are each rated for 50 V and the ripple current capacity is greater than 3 A, both
providing ample margin. It is important that the maximum ratings for voltage and current are not exceeded under
any circumstance.
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
13
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
9.2.2.4 Output Filter Components
Two components need to be selected for the output filter, L1 and C9. Since the TPS54233 is an externally
compensated device, a wide range of filter component types and values can be supported.
9.2.2.4.1 Inductor Selection
To calculate the minimum value of the output inductor, use Equation 8
LMIN =
VOUT(MAX) ´
(VIN(MAX) - VOUT )
VIN(MAX) ´ KIND ´ IOUT ´ FSW
(8)
KIND is a coefficient that represents the amount of inductor ripple current relative to the maximum output current.
This value is at the discretion of the designer; however, the following guidelines may be used. For designs using
low ESR output capacitors such as ceramics, a value as high as KIND = 0.3 may be used. When using higher
ESR output capacitors, KIND = 0.2 yields better results.
For this design example, use KIND = 0.3 and the minimum inductor value is calculated to be 14.97μH. For this
design, the closest value 15μH was chosen.
For the output filter inductor, it is important that the RMS current and saturation current ratings not be exceeded.
The RMS inductor current can be found from Equation 9
IL(RMS) =
2
IOUT(MAX)
(
)
æ V
ö
OUT ´ VIN(MAX) - VOUT
1
÷
+
´ ç
ç VIN(MAX) ´ LOUT ´ FSW ´ 0.7 ÷
12
è
ø
2
(9)
and the peak inductor current can be determined with Equation 10
IL(PK) = IOUT(MAX) +
VOUT ´
(VIN(MAX)
- VOUT
)
1.4 ´ VIN(MAX) ´ LOUT ´ FSW
(10)
For this design, the RMS inductor current is 2.02 A and the peak inductor current is 2.43 A. The chosen inductor
is a Coilcraft MSS1038-153ML 15 μH. It has a saturation current rating of 3.86 A and an RMS current rating of
3.8 A, meeting these requirements. Smaller or larger inductor values can be used depending on the amount of
ripple current the designer wishes to allow so long as the other design requirements are met. Larger value
inductors will have lower ac current and result in lower output voltage ripple, while smaller inductor values will
increase ac current and output voltage ripple. Inductor values for use with the TPS54233 are in the range of
6.8 μH to 47 μH.
9.2.2.4.2 Capacitor Selection
The important design factors for the output capacitor are dc voltage rating, ripple current rating, and equivalent
series resistance (ESR). The dc voltage and ripple current ratings cannot be exceeded. The ESR is important
because along with the inductor current it determines the amount of output ripple voltage. The actual value of the
output capacitor is not critical, but some practical limits do exist. Consider the relationship between the desired
closed loop crossover frequency of the design and LC corner frequency of the output filter. In general, it is
desirable to keep the closed loop crossover frequency at less than 1/5 of the switching frequency. With high
switching frequencies such as the 300 kHz frequency of this design, internal circuit limitations of the TPS54233
limit the practical maximum crossover frequency to about 25 kHz. In general, the closed loop crossover
frequency should be higher than the corner frequency determined by the load impedance and the output
capacitor. This limits the minimum capacitor value for the output filter to:
CO _ min = 1 /(2 ´ p ´ RO ´ FCO _ max )
(11)
Where RO is the output load impedance (VO/IO) and fCO is the desired crossover frequency. For a desired
maximum crossover of 25 kHz the minimum value for the output capacitor is around 3.8μF. This may not satisfy
the output ripple voltage requirement. The output ripple voltage consists of two components; the voltage change
due to the charge and discharge of the output filter capacitance and the voltage change due to the ripple current
times the ESR of the output filter capacitor. The output ripple voltage can be estimated by:
14
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
é ( D - 0 .5 )
ù
+ R ESR ú
V O PP = I LPP ê
ë 4 ´ F SW ´ C O
û
(12)
Where NC is the number of output capacitors in parallel.
The maximum ESR of the output capacitor is determined by the amount of allowable output ripple as specified in
the initial design parameters; so the maximum specified ESR as listed in the capacitor data sheet is given by
Equation 13:
ESRmax =
VOPPMAX
ILPP
-
(D
- 0.5)
4 ´ FSW ´ CO
(13)
Where ΔVp-p is the desired peak-to-peak output ripple.
To meet the 100 mV p-p ripple requirement, a single 470 μF aluminum electrolytic output capacitor is chosen for
C9. This is a Panasonic, EEVFK1A471P rated at 10 V with a maximum ESR of 160 mΩ and a ripple current
rating of 600 mA.
The maximum RMS output ripple current can be calculated using Equation 14
æ VOUT × VIN(MAX) - VOUT ö
1
÷
ICOUT(RMS) =
× ç
ç VIN(MAX) × LOUT × FSW × NC ÷
12
è
ø
(
)
(14)
The calculated total RMS ripple current is 216 mA and the maximum total ESR required is 43 mΩ. These output
capacitors exceed the requirements by a wide margin and will result in a reliable, high-performance design. The
selected output capacitor must be rated for a voltage greater than the desired output voltage plus = the ripple
voltage. Any derating amount must also be included.
Other capacitor types work well with the TPS54233, depending on the needs of the application.
9.2.2.5 Compensation Components
The external compensation used with the TPS54233 allows for a wide range of output filter configurations. A
large range of capacitor values and types of dielectric are supported. The design example uses ceramic X5R
dielectric output capacitors, but other types are supported.
A Type II compensation scheme is recommended for the TPS54233. The compensation components are chosen
to set the desired closed loop cross over frequency and phase margin for output filter components. The type II
compensation has the following characteristics; a dc gain component, a low frequency pole, and a mid frequency
zero / pole pair.
The dc gain is determined by Equation 15:
Vggm ´ VREF
GDC =
VO
(15)
Where:
Vggm = 800
VREF = 0.8 V
The low-frequency pole is determined by Equation 16:
VPO = 1/ (2 ´ p ´ ROO ´ CZ )
(16)
The mid-frequency zero is determined by Equation 17:
FZ1 = 1/ (2 ´ p ´ R Z ´ CZ )
(17)
And, the mid-frequency pole is given by Equation 18:
FP1 = 1/ (2 ´ p ´ R Z ´ CP )
(18)
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
15
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
The first step is to choose the closed loop crossover frequency. In general, the closed-loop crossover frequency
should be less than 1/8 of the minimum operating frequency, but for the TPS54233it is recommended that the
maximum closed loop crossover frequency be not greater than 25 kHz. Next, the required gain and phase boost
of the crossover network needs to be calculated. By definition, the gain of the compensation network must be the
inverse of the gain of the modulator and output filter. For this design example, where the ESR zero is less than
the closed loop crossover frequency, the gain of the modulator and output filter can be approximated by
Equation 19:
æ RO ö
æ RO ö
Gain = 20 log ç
÷ - 20 log ç
÷
è RSENSE ø
è RESR ø
(19)
Where:
RSENSE = 1Ω/9
RO = VO/IO
RESR = Equivalent series resistance of the output capacitor
The phase loss is given by Equation 20:
PL = a tan (2 ´ p ´ FCO ´ RESR ´ CO ) - a tan (2 ´ p ´ FCO ´ RO ´ CO )
(20)
Where:
RESR = Equivalent series resistance of the output capacitor
RO = VO/IO
Now that the phase loss is known the required amount of phase boost to meet the phase margin requirement
can be determined. The required phase boost is given by Equation 21:
PB = (PM - 90 deg ) - PL
(21)
Where PM = the desired phase margin.
A zero / pole pair of the compensation network will be placed symmetrically around the intended closed loop
frequency to provide maximum phase boost at the crossover point. The amount of separation can be determined
by Equation 22 and the resultant zero and pole frequencies are given by Equation 23 and Equation 24
ö
æ PB
k = tanç
+ 45 deg ÷
ø
è 2
FZ 1 =
(22)
FCO
k
(23)
FP1 = FCO ´ k
(24)
The low-frequency pole is set so that the gain at the crossover frequency is equal to the inverse of the gain of the
modulator and output filter. Due to the relationships established by the pole and zero relationships, the value of
RZ can be derived directly by Equation 25 :
RZ =
VO ´ ROA ´ 0.98
GMCOMP ´ Vggm ´ VREF ´ RESR
(25)
Where:
VO = Output voltage
ROA = 8.696 MΩ
GMCOMP = 9 A/V
Vggm = 800
VREF = 0.8 V
RESR = Equivalent series resistance of the output capacitor
With RZ known, CZ and CP can be calculated using Equation 26 and Equation 27:
16
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
CZ =
CP =
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
1
2 ´ p ´ FZ 1 ´ Rz
(26)
1
2 ´ p ´ FP1 ´ Rz
(27)
For this design, a singe 470 μF output capacitor is used. The ESR is approximately .160 Ω. The desired closed
loop crossover frequency is 22000 Hz.
Using Equation 19 and Equation 20, the output stage gain and phase loss are equivalent as:
Gain = –3.114 dB
and
PL = –4.96 degrees
For 60 degrees of phase margin, Equation 21 requires no additional phase boost, so K can be set equal to 1.
Equation 22, Equation 23, and Equation 24 are used to find the zero and pole frequencies of:
FZ1 = 22000 Hz
And
FP1 = 22000 Hz
RZ, CZ, and CP are calculated using Equation 25, Equation 26, and Equation 27:
6
Rz =
Cz =
Cp =
2.5 ´ 8.696 ´ 10 ´ 0.98
= 30.5 kW
9 ´ 800 ´ 0.8 ´ 0.160
(28)
1
= 237 pF
2 ´ p ´ 22000 ´ 30500
(29)
1
= 237 pF
2 ´ p ´ 22000 ´ 30500
(30)
Using standard values for R3, C6, and C7 in the application schematic of Figure 12:
R3 = 30.9 kΩ
C6 = 220 pF
C7 = 220 pF
The measured overall loop response for the circuit is given in Figure 12. Note that the actual closed loop
crossover frequency is higher than intended at about 25 kHz. This is primarily due to variation in the actual
values of the output filter components and tolerance variation of the internal feed-forward gain circuitry. Overall
the design has greater than 60 degrees of phase margin and will be completely stable over all combinations of
line and load variability.
9.2.2.6 Bootstrap Capacitor
Every TPS54233 design requires a bootstrap capacitor, C4. The bootstrap capacitor must be 0.1 μF. The
bootstrap capacitor is located between the PH pins and BOOT pin. The bootstrap capacitor should be a highquality ceramic type with X7R or X5R grade dielectric for temperature stability.
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
17
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
9.2.2.7 Catch Diode
The TPS54233 is designed to operate using an external catch diode between PH and GND. The selected diode
must meet the absolute maximum ratings for the application: Reverse voltage must be higher than the maximum
voltage at the PH pin, which is VINMAX + 0.5 V. Peak current must be greater than IOUTMAX plus on half the peak
to peak inductor current. Forward voltage drop should be small for higher efficiencies. It is important to note that
the catch diode conduction time is typically longer than the high-side FET on time, so attention paid to diode
parameters can make a marked improvement in overall efficiency. Additionally, check that the device chosen is
capable of dissipating the power losses. For this design, a Diodes, Inc. B340A is chosen, with a reverse voltage
of 40 V, forward current of 3 A, and a forward voltage drop of 0.5 V.
9.2.2.8 Output Voltage Limitations
Due to the internal design of the TPS54233, there are both upper and lower output voltage limits for any given
input voltage. The upper limit of the output voltage set point is constrained by the maximum duty cycle of 91%
and is given by Equation 31:
VOmax = 0.91 ×
((V
IN min
)
- IO max × RDS(on) max + VD
)-
(IO max
× RL ) - VD
(31)
Where:
VIN min = Minimum input voltage
IO max = Maximum load current
VD = Catch diode forward voltage
RL = Output inductor series resistance
The equation assumes maximum on resistance for the internal high-side FET.
The lower limit is constrained by the minimum controllable on time which may be as high as 160 ns. The
approximate minimum output voltage for a given input voltage and minimum load current is given by Equation 32:
VOmin = 0.051 ´
((VIN max
- IOmin ´ Rin ) + VD ) - (IO min ´ RL
)
- VD
(32)
Where:
VIN max = Maximum input voltage
IO min = Minimum load current
VD = Catch diode forward voltage
RL = Output inductor series resistance
This equation assumes nominal on-resistance for the high-side FET and accounts for worst case variation of
operating frequency set point. Any design operating near the operational limits of the device should be carefully
checked to assure proper functionality.
18
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
9.2.2.9 Power Dissipation Estimate
The following formulas show how to estimate the device power dissipation under continuous conduction mode
operations. They should not be used if the device is working in the discontinuous conduction mode (DCM) or
pulse skipping Eco-modeTM.
The device power dissipation includes:
1) Conduction loss: Pcon = Iout2 x RDS(on) x VOUT/VIN
2) Switching loss: Psw = 0.5 x 10-9 x VIN2 x IOUT x Fsw
3) Gate charge loss: Pgc = 22.8 x 10-9 x Fsw
4) Quiescent current loss: Pq = 0.075 x 10-3 x VIN
Where:
IOUT is the output current (A).
RDS(on) is the on-resistance of the high-side MOSFET (Ω).
VOUT is the output voltage (V).
VIN is the input voltage (V).
Fsw is the switching frequency (Hz).
So
Ptot = Pcon + Psw + Pgc + Pq
For given TA , TJ = TA + Rth x Ptot.
For given TJMAX = 150°C, TAMAX = TJMAX– Rth x Ptot.
Where:
Ptot is the total device power dissipation (W).
TA is the ambient temperature (°C).
TJ is the junction temperature (°C) .
Rth is the thermal resistance of the package (°C/W).
TJMAX is maximum junction temperature (°C).
TAMAX is maximum ambient temperature (°C).
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
19
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
9.2.3 Application Curves
100
100
VO = 3.3 V
95
VIN = 8 V
VIN = 12 V
95
VIN = 15 V
VIN = 8 V
90
VIN = 12 V
VIN = 15 V
90
Efficiency - %
Efficiency - %
85
85
VIN = 18 V
80
75
80
75
VIN = 18 V
70
65
70
60
65
55
50
60
0
0.25
1
1.25 1.5
0.5 0.75
IO - Output Current - A
1.75
0
2
40
60 80 100 120 140 160 180 200
IO - Output Current - mA
Figure 14. TPS54233 Low Current Efficiency
Figure 13. TPS54233 Efficiency
0.05
0.025
0.04
0.020
IO = 1 A
0.015
0.02
VIN = 18 V
Output Regulation - %
0.03
Output Regulation - %
20
VIN = 8 V
VIN = 12 V
0.01
0
-0.01
VIN = 15 V
-0.02
0.010
0.005
0
-0.005
-0.010
-0.015
-0.03
-0.020
-0.025
-0.04
0
0.2 0.4
0.6 0.8 1 1.2 1.4
IO - Output Current - A
1.6 1.8
8
2
Figure 15. TPS54233 Load Regulation
9
10
11 12 13 14 15
VI - Input Voltage -V
16
17
18
Figure 16. TPS54233 Line Regulation
180
60
Gain
Phase
VOUT
IOUT
-180
-60
10
1M
f - Frequency - Hz
Figure 18. TPS54233 Loop Response
Figure 17. TPS54233 Transient Response
20
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
VOUT
VIN
PH
PH
Figure 20. TPS54233 Output Ripple
Figure 19. TPS54233 Input Ripple
VIN
ENA
VOUT
VOUT
Figure 22. TPS54233 Start-up Relative to Enable
Figure 21. TPS54233 Start Up
VOUT
PH
Figure 23. TPS54233 Eco-mode™ Operation
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
21
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
10 Power Supply Recommendations
The device is designed to operate from an input-voltage supply range between 3.5 V and 28 V. This input supply
should be well regulated. If the input supply is located more than a few inches from the converter additional bulk
capacitance may be required in addition to the ceramic bypass capacitors. An electrolytic capacitor with a value
of 100 μF is a typical choice.
11 Layout
11.1 Layout Guidelines
The VIN pin should be bypassed to ground with a low ESR ceramic bypass capacitor. Care should be taken to
minimize the loop area formed by the bypass capacitor connections, the VIN pin, and the anode of the catch
diode. The typical recommended bypass capacitance is 10 μF ceramic with a X5R or X7R dielectric and the
optimum placement is closest to the VIN pins and the source of the anode of the catch diode. See Figure 24 for
a PCB layout example. The GND D pin should be tied to the PCB ground plane at the pin of the IC. The source
of the low-side MOSFET should be connected directly to the top side PCB ground area used to tie together the
ground sides of the input and output capacitors as well as the anode of the catch diode. The PH pin should be
routed to the cathode of the catch diode and to the output inductor. Since the PH connection is the switching
node, the catch diode and output inductor should be located very close to the PH pins, and the area of the PCB
conductor minimized to prevent excessive capacitive coupling. For operation at full rated load, the top side
ground area must provide adequate heat dissipating area. The TPS54233 uses a fused lead frame so that the
GND pin acts as a conductive path for heat dissipation from the die. Many applications have larger areas of
internal or back side ground plane available, and the top side ground area can be connected to these areas
using multiple vias under or adjacent to the device to help dissipate heat. The additional external components
can be placed approximately as shown. It may be possible to obtain acceptable performance with alternate
layout schemes, however this layout has been shown to produce good results and is intended as a guideline.
11.2 Layout Example
OUTPUT
FILTER
CAPACITOR
TOPSIDE
GROUND
AREA
Route BOOT CAPACITOR
trace on other layer to provide
wide path for topside ground
Vout
Feedback Trace
OUTPUT
INDUCTOR
CATCH
DIODE
PH
INPUT
BYPASS
CAPACITOR
BOOT
Vin
UVLO
RESISTOR
DIVIDER
VIN
GND
EN
COMP
SS
VSENSE
SLOW START
CAPACITOR
Thermal VIA
BOOT
CAPACITOR
PH
COMPENSATION
NETWORK
RESISTOR
DIVIDER
Signal VIA
Figure 24. TPS54233 Board Layout
22
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
TPS54233
www.ti.com
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
11.3 Estimated Circuit Area
The estimated printed circuit board area for the components used in the design of Figure 12 is 0.72 in2. This area
does not include test points or connectors.
11.4 Electromagnetic Interference (EMI) Considerations
As EMI becomes a rising concern in more and more applications, the internal design of the TPS54233 takes
measures to reduce the EMI. The high-side MOSFET gate drive is designed to reduce the PH pin voltage
ringing. The internal IC rails are isolated to decrease the noise sensitivity. A package bond wire scheme is used
to lower the parasitics effects.
To achieve the best EMI performance, external component selection and board layout are equally important.
Follow the Detailed Design Procedure above to prevent potential EMI issues.
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
23
TPS54233
SLUS859C – OCTOBER 2008 – REVISED JANUARY 2015
www.ti.com
12 Device and Documentation Support
12.1 Device Support
12.1.1 Development Support
For the WEBENCH Software Tool, go to www.TI.com/WEBENCH.
12.2 Trademarks
Eco-mode, PowerPAD are trademarks of Texas Instruments.
WEBENCH is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
24
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TPS54233
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TPS54233D
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 150
54233
TPS54233DR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 150
54233
TPS54233DRG4
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 150
54233
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of