Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
TPS5461x 3-V to 6-V Input, 6-A Output Synchronous Buck PWM Switcher With Integrated
FETs (SWIFT™)
1 Features
3 Description
•
The SWIFT™ family of dc/dc regulators, the
TPS54611, TPS54612, TPS54613, TPS54614,
TPS54615 and TPS54616 low-input voltage highoutput current synchronous-buck PWM converters
integrate all required active components. Included on
the substrate are true, high-performance, voltage
error amplifiers that provide high performance under
transient conditions; an under-voltage-lockout circuit
to prevent start-up until the input voltage reaches 3 V;
an internally and externally set slow-start circuit to
limit in-rush currents; and a powergood output useful
for processor/logic reset, fault signaling, and supply
sequencing.
1
•
•
•
•
•
•
30-mΩ, 12-A Peak MOSFET Switches for High
Efficiency at 6-A Continuous Output Source and
Sink
0.9-V, 1.2-V, 1.5-V, 1.8-V, 2.5-V, and 3.3-V Fixed
Output Voltage Devices With 1.0% Initial Accuracy
Internally Compensated for Easy Use and Minimal
Component Count
Fast Transient Response
Wide PWM Frequency − Fixed 350 kHz, 550 kHz
or Adjustable 280 kHz to 700 kHz
Load Protected by Peak Current Limit and
Thermal Shutdown
Integrated Solution Reduces Board Area and
Total Cost
2 Applications
•
•
•
•
Low-Voltage, High-Density Systems With Power
Distributed at 5 V or 3.3 V
Point of Load Regulation for High Performance
DSPs, FPGAs, ASICs and Microprocessors
Broadband, Networking and Optical
Communications Infrastructure
Portable Computing/Notebook PCs
The TPS5461x devices are available in a thermally
enhanced 28-pin TSSOP (PWP) PowerPAD™
package, which eliminates bulky heatsinks. TI
provides evaluation modules and the SWIFT™
designer software tool to aid in quickly achieving
high-performance power supply designs to meet
aggressive equipment development cycles.
Device Information(1)
PART NUMBER
PACKAGE
OUTPUT VOLTAGE
TPS54611
0.9 V
TPS54612
1.2 V
TPS54613
1.5 V
HTSSOP (28)
TPS54614
1.8 V
TPS54615
2.5 V
TPS54616
3.3 V
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Simplified Schematic
Efficiency at 350 kHz
100
Output
Input
PH
95
TPS54614
BOOT
90
PGND
VBIAS VSENSE
AGND
85
Efficiency - %
VIN
80
75
70
65
60
55
50
0
1
2
3
4
5
6
Load Current - A
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
4
5
7
Absolute Maximum Ratings ......................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Dissipation Ratings ...................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 9
7.1 Overview ................................................................... 9
7.2 Functional Block Diagram ......................................... 9
7.3 Feature Description................................................... 9
7.4 Device Functional Modes........................................ 12
8
Application and Implementation ........................ 13
8.1 Application Information............................................ 13
8.2 Typical Application ................................................. 13
9 Power Supply Recommendations...................... 16
10 Layout................................................................... 16
10.1 Layout Guidelines ................................................. 16
10.2 Layout Example .................................................... 17
10.3 Thermal Considerations ........................................ 17
11 Device and Documentation Support ................. 19
11.1
11.2
11.3
11.4
Device Support......................................................
Related Links ........................................................
Trademarks ...........................................................
Glossary ................................................................
19
19
19
19
12 Mechanical, Packaging, and Orderable
Information ........................................................... 19
4 Revision History
Changes from Revision C (April 2005) to Revision D
•
2
Page
Added Feature Description section, Device Functional Modes, Application and Implementation section, Power
Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical,
Packaging, and Orderable Information section. .................................................................................................................... 1
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
www.ti.com
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
5 Pin Configuration and Functions
TPS5461x PWP Package
28-Pin HTSSOP
Top View
AGND
VSENSE
NC
PWRGD
BOOT
PH
PH
PH
PH
PH
PH
PH
PH
PH
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
THERMAL 22
PAD
21
20
19
18
17
16
15
RT
FSEL
SS/ENA
VBIAS
VIN
VIN
VIN
VIN
VIN
PGND
PGND
PGND
PGND
PGND
Pin Functions
PIN
TYPE (1)
DESCRIPTION
NAME
NO.
AGND
1
G
Analog ground. Return for slow-start capacitor, VBIAS capacitor, RT resistor FSEL. Make PowerPAD
connection to AGND.
BOOT
5
S
Bootstrap input. 0.022-µF to 0.1-µF low-ESR capacitor connected from BOOT to PH generates floating
drive for the high-set FET driver.
FSEL
27
I
Frequency select input. Provides logic input to select between two internally set switching frequencies.
NC
3
–
No connection
PGND
15−19
G
Power ground. High current return for the low-side driver and power MOSFET. Connect PGND with large
copper areas to the input and output supply returns, and negative terminals of the input and output
capacitors.
PH
6−14
O
Phase input/output. Junction of the internal high-side and low-side power MOSFETs, and output inductor.
PWRGD
4
O
Powergood open-drain output. High-Z when VSENSE ≥ 90% Vref, otherwise PWRGD is low. Note that
output is low when SS/ENA is low or internal shutdown signal active.
RT
28
I
Frequency setting resistor input. Connect a resistor from RT to AGND to set the switching frequency.
SS/ENA
26
I
Slow-start/enable input/output. Dual function pin which provides logic input to enable/disable device
operation and capacitor input to externally set the start-up time.
VBIAS
25
S
Internal bias regulator output. Supplies regulated voltage to internal circuitry. Bypass VBIAS pin to AGND
pin with a high quality, low-ESR 0.1-µF to 1-µF ceramic capacitor.
20−24
I
Input supply for the power MOSFET switches and internal bias regulator. Bypass VIN pins to PGND pins
close to device package with a high quality, low-ESR 1-µF to 10-µF ceramic capacitor.
2
I
Error amplifier inverting input. Connect directly to output voltage sense point.
VIN
VSENSE
(1)
I = Input, O = Output, S = Supply, G = Ground
Copyright © 2001–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
3
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
VI
Input voltage
VO
Output voltage
IO
Source current
IS
Sink current
Voltage differential
MIN
MAX
UNIT
VIN, SS/ENA, FSEL
−0.3
7
V
RT
−0.3
6
V
VSENSE
−0.3
4
V
BOOT
−0.3
17
V
VBIAS, PWRGD
−0.3
7
V
PH
−0.6
10
V
PH
Internally Limited
V
VBIAS
6
PH
12
A
SS/ENA, PWRGD
10
mA
0.3
V
AGND to PGND
–0.3
Continuous power dissipation
mA
See Thermal Information
TJ
Operating virtual junction temperature
–40
125
°C
Tstg
Storage temperature
−65
150
°C
(1)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
Controller Input Voltage, VIN
Junction Temperature, TJ
NOM
MAX
UNIT
3
6
V
–40
125
°C
6.3 Thermal Information (1)
TPS5461x
THERMAL METRIC (2)
RθJA
(1)
(2)
UNIT
PWP (28 PINS)
Junction-to-ambient thermal resistance, with solder
18.2
Junction-to-ambient thermal resistance, without solder
40.5
°C/W
Test Board Conditions:
(a) 3 inches × 3 inches, 4 layers, thickness: 0.062 inch
(b) 1.5 oz. copper traces located on the top of the PCB
(c) 1.5 oz. copper ground plane on the bottom of the PCB
(d) 0.5 oz. copper ground planes on the 2 internal layers
(e) 12 thermal vias. See Figure 19 for more information.
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
6.4 Dissipation Ratings (1) (2)
TA = 25°C
POWER RATING
28 Pin PWP with Solder
(1)
(2)
(3)
4
5.49
(3)
TA = 70 °C
POWER RATING
TA = 85 °C
POWER RATING
UNIT
3.02
2.20
W
For more information on the PWP package, refer to TI technical brief, SLMA002
Test Board Conditions:
(a) 3 inches × 3 inches, 4 layers, thickness: 0.062 inch
(b) 1.5 oz. copper traces located on the top of the PCB
(c) 1.5 oz. copper ground plane on the bottom of the PCB
(d) 0.5 oz. copper ground planes on the 2 internal layers
(e) 12 thermal vias. See Figure 19 for more information.
Maximum power dissipation may be limited by over-current protection
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
www.ti.com
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
Dissipation Ratings(1)(2) (continued)
TA = 25°C
POWER RATING
TA = 70 °C
POWER RATING
TA = 85 °C
POWER RATING
UNIT
2.48
1.36
0.99
W
28 Pin PWP without Solder
6.5 Electrical Characteristics
TJ = –40°C to 125°C, VI = 3 V to 6 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY VOLTAGE, VIN
VIN
Input voltage range
I(Q)
Quiescent current
3.0
6.0
fs = 350 kHz, FSEL ≤ 0.8 V, RT open, phase pin open
6.2
9.6
= 550 kHz, FSEL ≤ 2.5 V, RT open, phase pin open
8.4
12.8
1
1.4
2.95
3.0
fs
Shutdown, SS/ENA = 0 V
V
mA
UNDERVOLTAGE LOCK OUT
Start threshold voltage
UVLO
V
Stop threshold voltage
2.70
2.80
V
Hysteresis voltage
0.14
0.16
V
2.5
µs
Rising and falling edge deglitch
(1)
BIAS VOLTAGE
VBIAS
Output voltage
Output current
I(VBIAS) = 0
2.70
2.80
(2)
2.90
V
100
µA
OUTPUT VOLTAGE
TPS54611
TPS54612
TPS54613
VO
Output voltage
TPS54614
TPS54615
TPS54616
TJ = 25°C, VIN = 5 V
3 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40°C ≤ TJ ≤ 125°C
0.9
–2.0%
2.0%
TJ = 25°C, VIN = 5 V
3 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40°C ≤ TJ ≤ 125°C
1.2
–2.0%
2.0%
TJ = 25°C, VIN = 5 V
3 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40°C ≤ TJ ≤ 125°C
1.5
–2.0%
2.0%
TJ = 25°C, VIN = 5 V
3 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40°C ≤ TJ ≤ 125°C
1.8
–3.0%
3.0%
TJ = 25°C, VIN = 5 V
3 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40° ≤ TJ ≤ 125°C
2.5
–3.0%
3.0%
TJ = 25°C, VIN = 5 V
4 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40° ≤ TJ ≤ 125°C
3.3
−3.0%
3.0%
V
V
V
V
V
V
REGULATION
Line regulation (1) (3)
IL = 3 A, 350 ≤ fs ≤ 550 kHz, TJ = 85°C
Load regulation (1) (3)
IL = 0 A to 6 A, 350 ≤ fs ≤ 550 kHz, TJ = 85°C
0.088
%/V
0.0917
%/A
OSCILLATOR
Internally set – free running
frequency
Externally set – free running
frequency range
FSEL
FSEL ≤ 0.8 V, RT open
280
350
420
FSEL ≥ 2.5 V, RT open
440
550
660
RT = 180 kΩ (1% resistor to AGND) (1)
252
280
308
RT = 100 kΩ (1% resistor to AGND)
460
500
540
RT = 68 kΩ (1% resistor to AGND) (1)
663
700
762
High level threshold
2.5
0.8
Ramp amplitude (peak-to-peak) (1)
(1)
(2)
(3)
kHz
V
Low level threshold
Ramp valley (1)
kHz
V
0.75
V
1
V
Specified by design
Static resistive loads only
Tested using circuit in Figure 10.
Copyright © 2001–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
5
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
www.ti.com
Electrical Characteristics (continued)
TJ = –40°C to 125°C, VI = 3 V to 6 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Minimum controllable on time
MIN
TYP
(1)
Maximum duty cycle (1)
MAX
UNIT
200
ns
90%
ERROR AMPLIFIER
Error amplifier open loop voltage
gain (1)
Error amplifier unity gain
bandwidth (1)
Error amplifier common mode input
voltage range
3
Powered by internal LDO (1)
26
dB
5
MHz
0
VBIAS
V
70
85
ns
1.20
1.40
V
PWM COMPARATOR
PWM comparator propagation delay
time, PWM comparator input to PH 10-mV overdrive (1)
pin (excluding deadtime)
SLOW-START/ENABLE
Enable threshold voltage, SS/ENA
0.82
Enable hysteresis voltage,
SS/ENA (1)
Falling edge deglitch, SS/ENA (1)
Internal slow-start
time (1)
0.03
V
2.5
µs
TPS54611
2.6
3.3
4.1
TPS54612
3.5
4.5
5.4
TPS54613
4.4
5.6
6.7
TPS54614
2.6
3.3
4.1
TPS54615
3.6
4.7
5.6
TPS54616
4.7
6.1
7.6
Charge current, SS/ENA
SS/ENA = 0V
Discharge current, SS/ENA
SS/ENA = 0.2 V, VI = 2.7 V
ms
3
5
8
µA
1.5
2.3
4.0
mA
POWERGOOD
Powergood threshold voltage
VSENSE falling
Powergood hysteresis voltage
See
(1)
Powergood falling edge deglitch
See
(1)
Output saturation voltage, PWRGD
I(sink) = 2.5 mA
Leakage current, PWRGD
VI = 5.5 V
90
%VO
3
%VO
35
0.18
µs
0.3
V
1
µA
CURRENT LIMIT
Current limit
VI = 3 V (1)
7.2
10
(1)
10
12
VI = 6 V
A
Current limit leading edge blanking
time (1)
100
ns
Current limit total response time (1)
200
ns
THERMAL SHUTDOWN
Thermal shutdown trip point (1)
135
Thermal shutdown hysteresis (1)
150
165
10
°C
OUTPUT POWER MOSFETS
rDS(on)
(4)
6
Power MOSFET switches
IO = 3 A, VI = 6 V (4)
26
47
IO = 3 A, VI = 3 V (4)
36
65
mΩ
Matched MOSFETs, low-side rDS(on) production tested, high-side rDS(on) specified by design.
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
www.ti.com
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
6.6 Typical Characteristics
100
Drain-Source On-State Resistance − Ω
Drain-Source On-State Resistance − Ω
120
VI = 3.3 V
IO = 3 A
100
80
60
40
20
0
25
85
IO = 3 A
60
40
20
0
−40
0
−40
VI = 5 V
80
125
0
25
85
125
Figure 1. Drain-source On-state Resistance vs Junction
Temperature
Figure 2. Drain-source On-state Resistance vs Junction
Temperature 2
f - Externally Set Oscillator Frequency - kHz
TJ − Junction Temperature − °C
f - Internally Set Oscillator Frequency - kHz
TJ − Junction Temperature − °C
650
FSEL ≥ 2.5 V
550
450
FSEL ≤ 0.8 V
350
250
−40
0
25
85
125
800
RT = 68 k
700
600
RT = 100 k
500
400
RT = 180 k
300
200
−40
0
25
85
125
TJ − Junction Temperature − °C
TJ − Junction Temperature − °C
Figure 3. Internally Set Oscillator Frequency vs Junction
Temperature 3
Figure 4. Externally Set Oscillator Frequency vs Junction
Temperature 4
0.8950
0.895
VO − Output Voltage Regulation − V
Vref − Voltage Reference - V
TA = 85°C
0.893
0.891
0.889
0.887
0.885
−40
0.8930
0.8910
0.8890
f = 350 kHz
0.8870
0.8850
0
25
85
125
3
TJ − Junction Temperature − °C
4
5
VI − Input Voltage − V
6
Tested using TPS54611
Figure 5. Voltage Reference vs Junction Temperature
Copyright © 2001–2015, Texas Instruments Incorporated
Figure 6. Output Voltage Regulation vs Input Voltage
Submit Documentation Feedback
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
7
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
www.ti.com
Typical Characteristics (continued)
0
140
RL= 10 kΩ,
CL = 160 pF,
TA = 25°C
Gain − dB
100
−60
Phase
80
−80
−100
60
−120
40
Internal Slow-Start Time − ms
−40
Gain
−140
20
Phase − Degrees
120
3.80
−20
−160
0
−180
−20
−200
10 k 100 k 1 M 10 M
0
10
100
1k
3.65
3.50
3.35
3.20
3.05
2.90
2.75
−40
f − Frequency − Hz
0
25
85
TJ − Junction Temperature − °C
125
Tested using TPS54611
Figure 7. Error Amplifier Open Loop Response
Figure 8. Internal Slow-Start Time vs Junction Temperature
5
TJ = 125°C
FS = 700 kHz
Device Power Losses − W
4.5
4
VI = 3.3 V
3.5
3
2.5
2
1.5
VI = 5.0 V
1
0.5
0
0
1
2
3
4
5
6
7
8
IL − Load Current − A
Figure 9. Device Power Losses vs Load Current
8
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
www.ti.com
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
7 Detailed Description
7.1 Overview
The SWIFT family of DC - DC regulators, the TPS54611, TPS54612, TPS54613, TPS54614, TPS54615, and
TPS54616 are low-input voltage high-output current synchronous-buck PWM converters integrate all required
active components. Included on the substrate are true, high-performance, voltage error amplifiers that provide
high performance under transient conditions; an under-voltage-lockout circuit to prevent start-up until the input
voltage reaches 3 V; an internally and externally set slow-start circuit to limit in-rush currents; and a powergood
output useful for processor/logic reset, fault signaling, and supply sequencing.
7.2 Functional Block Diagram
AGND
VBIAS
VIN
Enable
5 µA Comparator
SS/ENA
Falling
Edge
Deglitch
1.8 V
Hysteresis: 0.03
V
VIN UVLO
Comparator
VIN
2.94 V
Hysteresis: 0.16
V
VIN
ILIM
Comparator
Thermal
Shutdown
145°C
2.5 µs
REG
VBIAS
SHUTDOWN
VIN
Leading
Edge
Blanking
Falling
and
Rising
Edge
Deglitch
100 ns
BOOT
Sensefet
30 mΩ
2.5 µs
SS_DIS
SHUTDOWN
Internal/External
Slow-Start
(Internal Slow-Start Time
=
3.3 ms to 6.6 ms)
VI
PH
+
−
S
40 kΩ
Error
Amplifier
VI
Feed-Forward
Compensation
PWM
Comparator
25 ns Adaptive
Deadtime
VO
CO
Adaptive Dead-Time
and
Control Logic
R Q
2 kΩ
LOUT
VIN
30 mΩ
OSC
PGND
Power good
Comparator
Reference/
DAC
Falling
Edge
Deglitch
VSENSE
0.90 Vref
TPS5461x
Hysteresis: 0.03 Vref
VSENSE
RT
SHUTDOWN
PWRGD
35 µs
FSEL
7.3 Feature Description
7.3.1 Undervoltage Lock Out (UVLO)
The TPS5461x incorporates an UVLO circuit to keep the device disabled when the input voltage (VIN) is
insufficient. During power up, internal circuits are held inactive until VIN exceeds the nominal UVLO threshold
voltage of 2.95 V. Once the UVLO start threshold is reached, device start-up begins. The device operates until
VIN falls below the nominal UVLO stop threshold of 2.8 V. Hysteresis in the UVLO comparator, and a 2.5-µs
rising and falling edge deglitch circuit, reduces the likelihood of shutting the device down due to noise on VIN.
Copyright © 2001–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
9
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
www.ti.com
Feature Description (continued)
7.3.2 Slow-Start and Enable (SS/ENA)
The slow-start/enable pin provides two functions. First, the pin acts as an enable (shutdown) control by keeping
the device turned off until the voltage exceeds the start threshold voltage of approximately 1.2 V. When SS/ENA
exceeds the enable threshold, device start up begins. The reference voltage fed to the error amplifier is linearly
ramped up from 0 V to 0.891 V in 3.35 ms. Similarly, the converter output voltage reaches regulation in
approximately 3.35 ms. Voltage hysteresis and a 2.5-µs falling edge deglitch circuit reduce the likelihood of
triggering the enable due to noise. Refer to Table 1 for startup times for each device.
Table 1. Device Startup Times
DEVICE
OUTPUT VOLTAGE
SLOW-START
TPS54611
0.9 V
3.3 ms
TPS54612
1.2 V
4.5 ms
TPS54613
1.5 V
5.6 ms
TPS54614
1.8 V
3.3 ms
TPS54615
2.5 V
4.7 ms
TPS54616
3.3 V
6.1 ms
The second function of the SS/ENA pin provides an external means for extending the slow-start time with a
ceramic capacitor connected between SS/ENA and AGND. Adding a capacitor to the SS/ENA pin has two effects
on start-up. First, a delay occurs between release of the SS/ENA pin and start-up of the output. The delay is
proportional to the slow-start capacitor value and lasts until the SS/ENA pin reaches the enable threshold. The
start-up delay is approximately:
1.2 V
t d = C(SS) ´
5 mA
(1)
Second, as the output becomes active, a brief ramp up at the internal slow-start rate may be observed before the
externally set slow-start rate takes control and the output rises at a rate proportional to the slow-start capacitor.
The slow-start time set by the capacitor is approximately:
0.7 V
t(SS) = C(SS) ´
5 mA
(2)
The actual slow-start time is likely to be less than the above approximation due to the brief ramp up at the
internal rate
7.3.3 VBIAS Regulator
The VBIAS regulator provides internal analog and digital blocks with a stable supply voltage over variations in
junction temperature and input voltage. A high quality, low-ESR, ceramic bypass capacitor is required on the
VBIAS pin. X7R or X5R grade dielectrics are recommended because their values are more stable over
temperature. The bypass capacitor should be placed close to the VBIAS pin and returned to AGND.
External loading on VBIAS is allowed, with the caution that internal circuits require a minimum VBIAS of 2.7 V,
and external loads on VBIAS with ac or digital switching noise may degrade performance. The VBIAS pin may be
useful as a reference voltage for external circuits.
7.3.4 Voltage Reference
The voltage reference system produces a precise, temperature-stable voltage from a bandgap circuit. A scaling
amplifier and DAC are then used to produce the reference voltages for each of the fixed output devices.
7.3.5 Oscillator and PWM Ramp
The oscillator frequency can be set to internally fixed values of 350 kHz or 550 kHz using the FSEL pin as a
static digital input. If a different frequency of operation is required for the application, the oscillator frequency can
be externally adjusted from 280 kHz to 700 kHz by connecting a resistor from the RT pin to AGND and floating
the FSEL pin. The switching frequency is approximated by the following equation, where R is the resistance from
RT to AGND
10
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
www.ti.com
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
Switching Frequency =
100 kW
´ 500 [kHz]
R
(3)
Table 2 summarizes the frequency selection configurations:
Table 2. Switching Frequencies
SWITCHING FREQUENCY
SYNC PIN
RT PIN
350 kHz, internally set
Float or AGND
Float
550 kHz, internally set
≥2.5 V
Float
Externally set 280 kHz to 700 kHz
Float
R = 180 k to 68 k
7.3.6 Error Amplifier
The high performance, wide bandwidth, voltage error amplifier is gain-limited to provide internal compensation of
the control loop. The user is given limited flexibility in choosing output L and C filter components. Inductance
values of 4.7 µH to 10 µH are typical and available from several vendors. The resulting designs exhibit good
noise and ripple characteristics, but with exceptional transient response. Transient recovery times are typically in
the range of 10 µs to 20 µs.
7.3.7 PWM Control
Signals from the error amplifier output, oscillator, and current limit circuit are processed by the PWM control logic.
Referring to the internal block diagram, the control logic includes the PWM comparator, OR gate, PWM latch,
and portions of the adaptive dead-time and control logic block. During steady-state operation below the current
limit threshold, the PWM comparator output and oscillator pulse train alternately set and reset the PWM latch.
Once the PWM latch is set, the low-side FET remains on for a minimum duration set by the oscillator pulse
width. During this period, the PWM ramp discharges rapidly to its valley voltage. When the ramp begins to
charge back up, the low-side FET turns off and high-side FET turns on. As the PWM ramp voltage exceeds the
error amplifier output voltage, the PWM comparator resets the latch, thus turning off the high-side FET and
turning on the low-side FET. The low-side FET remains on until the next oscillator pulse discharges the PWM
ramp.
During transient conditions, the error amplifier output could be below the PWM ramp valley voltage or above the
PWM peak voltage. If the error amplifier is high, the PWM latch is never reset, and the high-side FET remains on
until the oscillator pulse signals the control logic to turn the high-side FET off and the low-side FET on. The
device operates at its maximum duty cycle until the output voltage rises to the regulation set-point, setting
VSENSE to approximately the same voltage as Vref. If the error amplifier output is low, the PWM latch is
continually reset and the high-side FET does not turn on. The low-side FET remains on until the VSENSE
voltage decreases to a range that allows the PWM comparator to change states. The TPS5461x devices are
capable of sinking current continuously until the output reaches the regulation set-point.
If the current limit comparator trips for longer than 100 ns, the PWM latch resets before the PWM ramp exceeds
the error amplifier output. The high-side FET turns off and the low-side FET turns on to decrease the energy in
the output inductor and consequently decrease the output current. This process is repeated each cycle in which
the current limit comparator is tripped.
7.3.8 Dead-Time Control and MOSFET Drivers
Adaptive dead-time control prevents shoot-through current from flowing in both N-channel power MOSFETs
during the switching transitions by actively controlling the turnon times of the MOSFET drivers. The high-side
driver does not turn on until the voltage at the gate of the low-side FET is below 2 V. The high-side and low-side
drivers are designed with 300 mA source and sink capability to quickly drive the power MOSFETs gates. The
low-side driver is supplied from VIN, while the high-side drive is supplied from the BOOT pin. A bootstrap circuit
uses an external BOOT capacitor and internal 2.5-Ω bootstrap switch connected between the VIN and BOOT
pins. The integrated bootstrap switch improves drive efficiency and reduces external component count.
Copyright © 2001–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
11
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
www.ti.com
7.3.9 Overcurrent Protection
Cycle-by-cycle current limiting is achieved by sensing the current flow through the high-side MOSFET and a
differential amplifier with preset overcurrent threshold. The high-side MOSFET is turned off within 200 ns of
reaching the current limit threshold. A 100 ns leading edge blanking circuit prevents false tripping of current limit.
Current limit detection occurs only when current flows from VIN to PH when sourcing current to the output filter.
Load protection during current sink operation is provided by thermal shutdown.
7.3.10 Thermal Shutdown
The device uses the thermal shutdown to turn off the power MOSFETs and disable the controller if the junction
temperature exceeds 150°C. The device is released from shutdown when the junction temperature decreases to
10°C below the thermal shutdown trip point, and starts up under control of the slow-start circuit. Thermal
shutdown provides protection when an overload condition is sustained for several milliseconds. With a persistent
fault condition, the device cycles continuously: starting up by control of the slow-start circuit, heating up due to
the fault, and then shutting down upon reaching the thermal shutdown trip point.
7.3.11 Powergood (PWRGD)
The powergood circuit monitors for undervoltage conditions on VSENSE. If the voltage on VSENSE falls 10%
below the reference voltage, the open-drain PWRGD output is pulled low. PWRGD is also pulled low if VIN is
less than the UVLO threshold, or SS/ENA is low, or thermal shutdown is asserted. When VIN = UVLO threshold,
SS/ENA = enable threshold, and VSENSE > 90% of Vref, the open-drain output of the PWRGD pin is high. A
hysteresis voltage equal to 3% of Vref and a 35-µs falling edge deglitch circuit prevent tripping of the powergood
comparator due to high-frequency noise.
7.4 Device Functional Modes
7.4.1 Continuous Conduction Mode
These devices operate in continuous conduction mode (CCM) at a fixed frequency regardless of the output
current.
12
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
www.ti.com
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The TPS5461x devices are fixed output voltage synchronous step-down DC-DC converters. These devices are
used to convert a higher DC input voltage to a lower DC output voltage with a maximum output current of 6A.
8.2 Typical Application
Figure 10 shows the schematic diagram for a typical TPS54614 application. The TPS54614 (U1) can provide
greater than 6 A of output current at a nominal output voltage of 1.8 V. For proper operation, the exposed
thermal PowerPAD underneath the integrated circuit package needs to be soldered to the printed-circuit board.
VI
3V−6V
20
220 µF
10 µF
21
VIN
BOOT
VIN
PH
22
VIN
23
VIN
7
PH
8
PH
9
PH
10
PH
11
PH
12
PH
13
PH
14
PH
15
PGND
PGND 16
17
PGND
18
PGND
19
PGND
24
VIN
10 kΩ
27
28
PwrGood
26
25
4
Enable
3
0.1 µF
5
6
2
CSS
FSEL
RT
SS/ENA
VBIAS
PWRGD
NC
VSENSE
1
AGND
0.047 µF
7.2 µH
VO
1.8 V
680 µF
PwrPad
Figure 10. Application Circuit
8.2.1 Design Requirements
The design requirements for this example are listed in Table 3.
Table 3. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
DC Input Voltage Range
3V–6V
DC Output Voltage
1V
DC Output Current Range
0A – 6 A
Load Transient Step
3A – 6 A
Load Regulation Control
± 5 mV
Loop Crossover Frequency
50 kHz
Control Loop Phase Margin
55°
Copyright © 2001–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
13
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
www.ti.com
8.2.2 Detailed Design Procedure
8.2.2.1 Component Selection
The values for the components used in this design example were selected using the SWIFT designer software
tool. SWIFT designer provides a complete design environment for developing dc-dc converters using the
TPS54614, or other devices in the SWIFT product family. Additional design information is available at
www.ti.com.
8.2.2.2 Input Filter
The input to the circuit is a nominal 3.3 VDC or 5 VDC. The input filter is a 220-μF POSCAP capacitor, with a
maximum allowable ripple current of 3 A. A 10-µF ceramic capacitor for the TPS54614 is required, and must be
located as close as possible to the device.
8.2.2.3 Feedback Circuit
The output voltage of the converter is fed directly into the VSENSE pin of the TPS54614. The TPS54614 is
internally compensated to provide stability of the output under varying line and load conditions.
8.2.2.4 Operating Frequency
In the application circuit, 350 kHz operation is selected by leaving FSEL open. Different operating frequencies
can be selected by connecting a resistor between RT pin and AGND. Choose the value of R using Equation 4 for
the desired operating frequency:
500 kHz
R=
´ 100 kW
SwitchingFrequency
(4)
Alternately, a preset operating frequency of 550 kHz can be selected by leaving RT open and connecting the
FSEL pin to VI.
8.2.2.5 Output Filter
The output filter is composed of a 5.2-µH inductor and a 470-µF capacitor. The inductor is low dc resistance (16mΩ) type, Sumida CDRH104R−5R2. The capacitor used is a 4-V POSCAP with a maximum ESR of 40 mΩ. The
output filter components work with the internal compensation network to provide a stable closed loop response
for the converter.
8.2.3 Application Curves
100
1.03
1.02
VO − Output Voltage − V
90
Efficiency − %
VI = 5 V
VI = 3.3V
70
1.01
VI = 5 V
1
VI = 3.3V
0.99
60
0.98
50
0.97
0
1
2
3
4
5
6
7
8
9
10
IL − Load Current − A
Figure 11. Efficiency vs Load Current
14
Submit Documentation Feedback
0
1
2
3
4
5
6
7
8
9
10
IL − Load Current − A
Figure 12. Output Voltage vs Load Current
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
180
400
16
350
14
300
12
250
10
200
8
150
6
100
4
−10
50
2
−20
0
60
135
Phase
30
90
20
Gain
10
Phase − Degrees
Gain − dB
40
VO − Output Voltage − mV
50
45
0
10
100
1k
0
100 k
10 k
0
20
0
40 60 80 100 120 140 160 180 200
t − Time − µs
f − Frequency − Hz
Figure 14. Transient Response
Figure 13. Loop Response
80
7
70
VO − Output Voltage − mV
8
6
VI − Input Voltage − V
I O − Output Current − A
www.ti.com
5
4
3
2
1
60
50
40
30
20
10
0
0
0
2
4
6
8
10 12
14
16 18 20
0
20
40 60 80 100 120 140 160 180 200
t − Time − µs
t − Time − µs
Figure 15. Start-up Waveforms
Figure 16. Output Ripple Voltage
125
TJ = 125°C
FS = 700 kHz
T A − Ambient Temperature − ° C
115
105
VI = 5 V
95
85
75
65
VI = 3.3 V
55
45
Safe Operating Area
35
25
0
1
2
3
4
5
6
7
8
IL − Load Current − A
Figure 17. Ambient Temperature vs Load Current
Copyright © 2001–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
15
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
www.ti.com
9 Power Supply Recommendations
These devices operate from an input supply voltage between 3 V and 6 V. This supply must be well-regulated.
Proper bypassing of input supplies and internal regulators is critical for noise performance, as is good PCB layout
practice. See the recommendations in Layout.
10 Layout
10.1 Layout Guidelines
Figure 18 shows a generalized PCB layout guide for the TPS5461x.
• The VIN pins should be connected together on the printed circuit board (PCB) and bypassed with a low ESR
ceramic bypass capacitor. Care should be taken to minimize the loop area formed by the bypass capacitor
connections, the VIN pins, and the TPS54311−16 ground pins. The minimum recommended bypass
capacitance is 10-μF ceramic with a X5R or X7R dielectric and the optimum placement is closest to the VIN
pins and the PGND pins.
• The TPS54311−16 has two internal grounds (analog and power). Inside the TPS54311−16, the analog
ground ties to all of the noise sensitive signals, while the power ground ties to the noisier power signals.
Noise injected between the two grounds can degrade the performance of the TPS54311−16, particularly at
higher output currents. Ground noise on an analog ground plane can also cause problems with some of the
control and bias signals. For these reasons, separate analog and power ground traces are recommended.
There should be an area of ground one the top layer directly under the IC, with an exposed area for
connection to the PowerPAD. Use vias to connect this ground area to any internal ground planes. Use
additional vias at the ground side of the input and output filter capacitors as well. The AGND and PGND pins
should be tied to the PCB ground by connecting them to the ground area under the device as shown. The
only components that should tie directly to the power ground plane are the input capacitors, the output
capacitors, the input voltage decoupling capacitor, and the PGND pins of the TPS54311−16. Use a separate
wide trace for the analog ground signal path. This analog ground should be used for the timing resistor RT,
slow start capacitor and bias capacitor grounds. Connect this trace directly to AGND (pin 1).
• The PH pins should be tied together and routed to the output inductor. Since the PH connection is the
switching node, inductor should be located very close to the PH pins and the area of the PCB conductor
minimized to prevent excessive capacitive coupling.
• Connect the boot capacitor between the phase node and the BOOT pin as shown. Keep the boot capacitor
close to the IC and minimize the conductor trace lengths.
• Connect the output filter capacitor(s) as shown between the VOUT trace and PGND. It is important to keep
the loop formed by the PH pins, Lout, Cout and PGND as small as practical.
• Connect the output of the circuit directly to the VSENSE pin. Do not place this trace too close to the PH trace.
Do to the size of the IC package and the device pinout, they will have to be routed somewhat close, but
maintain as much separation as possible while still keeping the layout compact.
• Connect the bias capacitor from the VBIAS pin to analog ground using the isolated analog ground trace. If a
slow-start capacitor or RT resistor is used, or if the SYNC pin is used to select 350-kHz operating frequency,
connect them to this trace as well.
16
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
www.ti.com
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
10.2 Layout Example
ANALOG GROUND TRACE
FREQUENCY SET RESISTOR
AGND
RT
FSEL
VSENSE
NC
SLOW START
CAPACITOR
SS/ENA
BIAS CAPACITOR
PWRGD
BOOT
CAPACITOR
BOOT
PH
VOUT
PH
VBIAS
VIN
EXPOSED
POWERPAD
AREA
VIN
PH
VIN
PH
VIN
PH
VIN
PH
PGND
OUTPUT INDUCTOR
OUTPUT
FILTER
CAPACITOR
VIN
PGND
PGND
PGND
PGND
INPUT
BYPASS
CAPACITOR
INPUT
BULK
FILTER
TOPSIDE GROUND AREA
VIA to Ground Plane
Figure 18. TPS5461x PCB Layout
10.3 Thermal Considerations
For operation at full rated load current, the analog ground plane must provide adequate heat dissipating area. A
3 inch by 3 inch plane of 1 ounce copper is recommended, though not mandatory, depending on ambient
temperature and airflow. Most applications have larger areas of internal ground plane available, and the
PowerPAD should be connected to the largest area available. Additional areas on the top or bottom layers also
help dissipate heat, and any area available should be used when 3 A or greater operation is desired. Connection
from the exposes area of the PowerPAD to the analog ground plane layer should be made using 0.013 inch
diameter vias to avoid solder wicking through the vias. Eight vias should be in the PowerPAD area with four
additional vias located under the device package. The size of the vias under the package, but not in the exposed
thermal pad area, can be increased to 0.018. Additional vias beyond the ten recommended that enhance thermal
performance should be included in areas not under the device package.
Copyright © 2001–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
17
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
www.ti.com
Thermal Considerations (continued)
8 PL Ø 0.0130
4 PL
Ø 0.0180
Connect Pin 1 to Analog Ground Plane
in This Area for Optimum Performance
Minimum Recommended Thermal Vias: 8 x 0.013 Diameter Inside
Powerpad Area 4 x 0.018 Diameter Under Device as Shown.
Additional 0.018 Diameter Vias May Be Used if Top Side Analog Ground
Area Is Extended.
0.06
0.0150
0.0339
0.0650
0.0500
0.3820 0.3478 0.0500
0.0500
0.2090
0.0256
0.0650
0.0339
0.1700
0.1340
Minimum Recommended Top
Side Analog Ground Area
Minimum Recommended Exposed
Copper Area for Powerpad. 5mm
Stencils May Require 10 Percent
Larger Area
0.0630
0.0400
Figure 19. Recommended Land Pattern for 28-Pin PWP PowerPAD 12
18
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
TPS54611, TPS54612, TPS54613
TPS54614, TPS54615, TPS54616
www.ti.com
SLVS400D – AUGUST 2001 – REVISED JANUARY 2015
11 Device and Documentation Support
11.1 Device Support
11.1.1 Related DC - DC Products
• TPS40000—Low-input, voltage-mode synchronous buck controller
• TPS759xx—7.5-A low dropout regulator
• PT6440 series—6-A plugin modules
11.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 4. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
TPS54611
Click here
Click here
Click here
Click here
Click here
TPS54612
Click here
Click here
Click here
Click here
Click here
TPS54613
Click here
Click here
Click here
Click here
Click here
TPS54614
Click here
Click here
Click here
Click here
Click here
TPS54615
Click here
Click here
Click here
Click here
Click here
TPS54616
Click here
Click here
Click here
Click here
Click here
11.3 Trademarks
SWIFT, PowerPAD are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2001–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS54611 TPS54612 TPS54613 TPS54614 TPS54615 TPS54616
19
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
TPS54611PWP
ACTIVE
HTSSOP
PWP
28
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54611
Samples
TPS54612PWP
ACTIVE
HTSSOP
PWP
28
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54612
Samples
TPS54612PWPG4
ACTIVE
HTSSOP
PWP
28
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54612
Samples
TPS54612PWPR
ACTIVE
HTSSOP
PWP
28
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54612
Samples
TPS54612PWPRG4
ACTIVE
HTSSOP
PWP
28
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54612
Samples
TPS54613PWP
ACTIVE
HTSSOP
PWP
28
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54613
Samples
TPS54613PWPG4
ACTIVE
HTSSOP
PWP
28
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54613
Samples
TPS54613PWPR
ACTIVE
HTSSOP
PWP
28
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54613
Samples
TPS54614PWP
ACTIVE
HTSSOP
PWP
28
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54614
Samples
TPS54614PWPG4
ACTIVE
HTSSOP
PWP
28
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54614
Samples
TPS54614PWPR
ACTIVE
HTSSOP
PWP
28
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54614
Samples
TPS54615PWP
ACTIVE
HTSSOP
PWP
28
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54615
Samples
TPS54615PWPR
ACTIVE
HTSSOP
PWP
28
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54615
Samples
TPS54616PWP
ACTIVE
HTSSOP
PWP
28
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54616
Samples
TPS54616PWPG4
ACTIVE
HTSSOP
PWP
28
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54616
Samples
TPS54616PWPR
ACTIVE
HTSSOP
PWP
28
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TPS54616
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of