www.ti.com
Description
EVM User's Guide: TPS564252 TPS564255 TPS564257
Step-Down Converter Evaluation Module
Description
Features
TPS56425X evaluation module (EVM) is a simple,
easy-to-use, 4 A synchronous step-down converter
in SOT563 package. TPS56425XEVM is a fully
assembled and tested circuit for evaluating the
TPS56425X step-down converter. This EVM operates
from 3 V to 17 V input, 12 V nominal, and provides
a 1.05 V output at 4 A. The EVM also includes
AC signal injection terminals for feedback loop
measurements.
•
•
•
•
•
3 V to 17 V input voltage range
0.6 V to 10 V output voltage range
Up to 4 A output current
ECO mode / FCCM mode/ OOA mode
Fast transient response
Applications
•
•
•
•
•
WLAN/Wi-Fi access point, switch, router
Pro-audio, surveillance, drone
TV, STB and DVR, smart speaker
SSD
Electricity meter
Figure 1-1. TPS56425xEVM Board (Top Side)
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
1
Evaluation Module Overview
www.ti.com
1 Evaluation Module Overview
This user's guide introduces the TPS564252EVM, TPS564255EVM, and TPS564257EVM. These three devices
differ in their light load behavior. The TPS564252 operates in Eco-mode, the TPS564255 operates in OOA
mode, and the TPS564257 operates in FCCM mode. This user's guide contains information for the TPS564252,
TPS564255, and TPS564257 as well as support documentation for the TPS564252EVM, TPS564255EVM, and
TPS564257EVM evaluation modules. This document also includes the performance specifications, board layout,
schematic, and the list of materials of the TPS564252EVM, TPS564255EVM, and TPS564257EVM.
•
•
•
•
Performance specifications
Board layout
Schematic
List of materials
1.1 Introduction
In light-load conditions, the TPS564252 operates in Eco-mode to enable higher efficiency by varying the
switching frequency, the TPS564257 operates in FCCM to maintain constant switching frequency and the
TPS564255 operates in OOA mode to avoid audio noise. The main difference is at light loading, but the other
behaviors are similar. This user's guide mainly introduces the TPS564252 and includes some TPS564257 and
TPS564255 features that are different from the TPS564252.
The TPS56425x is a single, adaptive on-time, D-CAP3™ control mode, synchronous buck converter that requires
a very low external component count. The D-CAP3 control mode circuit is optimized for low-ESR output
capacitors such as POSCAP, SP-CAP, or ceramic types and features fast transient response with no external
compensation. The switching frequency is internally set at a nominal 600 KHz. The high-side and low-side
switching MOSFETs are incorporated inside the TPS56425x package along with the gate-drive circuitry. The low
drain-to-source on resistance of the MOSFETs and fast switching slew rate allow the TPS56425x to achieve
high efficiency and help keep the junction temperature low at high output currents. Power sequencing is possible
by correctly configuring the enable and power-good indicator. The TPS56425x DC/DC synchronous converter
is designed to support up to a 4-A continuous current from an input voltage source of 3 V to 17 V. The output
voltage range is from 0.6 V to 10 V. Rated input voltage and output current ranges for the evaluation module are
given in Table 1-1.
The TPS564252EVM evaluation module (EVM) is a single, synchronous buck converter providing 1.05 V at 4 A
from 3-V to 17-V input. This user’s guide describes the TPS564252EVM performance.
Table 1-1. Input Voltage and Output Current Summary
EVM
INPUT VOLTAGE (VIN) RANGE
OUTPUT CURRENT (IOUT)
RANGE
TPS564252EVM
VIN = 3 V to 17 V
0 A to 4 A
TPS564257EVM
VIN = 3 V to 17 V
0 A to 4 A
TPS564255EVM
VIN = 3 V to 17 V
0 A to 4 A
1.2 Kit Contents
•
•
One TPS56425XEVM board
EVM disclaimer Read Me
1.3 Specification
This EVM operates from 3 V to 17 V input, 12 V nominal, and provides a 1.05 V output at 4 A. The EVM also
includes AC signal injection terminals for feedback loop measurements. Specification, application information,
and schematic are shown in Section 4 and Section 5.1.
1.4 Device Information
Synchronous buck converter TPS56425X is used in the EVM to achieve the high-efficiency power delivery and
voltage conversion. The TPS564252 operates in Eco-mode, which maintains high efficiency during light loading.
The TPS564257 operates in FCCM mode, which keeps the same frequency and lower output ripple during all
load conditions. The TPS564255 operates in OOA mode, which prevents audio noise generation.
2
Step-Down Converter Evaluation Module
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com
Evaluation Module Overview
Device Information
PART NUMBER
Mode
TPS564252
ECO
TPS564255
OOA
TPS564257
FCCM
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Package
DRL (SOT-563, 6)
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
3
Performance Specification Summary
www.ti.com
2 Performance Specification Summary
A summary of the TPS564252EVM performance specifications is provided in Table 2-1. Specifications are given
for an input voltage of VIN = 12 V and an output voltage of 1.05 V, unless otherwise noted. The ambient
temperature is 25°C for all measurement, unless otherwise noted.
Table 2-1. Performance Specifications Summary
SPECIFICATIONS
TEST CONDITIONS
Input voltage range
MIN
TYP
MAX
3
12
17
Output voltage set point
Operating frequency
VIN = 12 V, IO = 2 A
Output current range
VIN = 12 V, LO = 1.5 µH
Output ripple voltage
VIN = 12 V, IO = 4 A
V
1.05
V
600
KHz
0
Over current limit
UNIT
4
A
5.6
A
11
mVPP
3 Output Voltage Setpoint
The output voltage of the EVM can be selected by changing the value of resistor R4 (RUPPER) and R5 (RLOWER).
The value of R4 for a specific output voltage can be calculated using Equation 1. The output voltage is set with a
resistor divider from the output node to the FB pin. TI recommends using 1% tolerance or better divider resistors.
Start with a 10 kΩ or 30 kΩ for R4 (RFBB) and use Equation 1 to calculate R5 (RFBT) . To improve efficiency at
light loads, consider using larger value resistors. If the values are too high, the regulator is more susceptible to
noise and voltage errors from the FB input current are noticeable.
R
VOUT = 0 . 6 × 1 + R4
(1)
5
4
Step-Down Converter Evaluation Module
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com
Test Setup and Results
4 Test Setup and Results
This section describes how to properly connect, set up, and use the TPS564252EVM. The section also includes
test results typical for the evaluation modules and the following:
•
•
•
•
•
•
•
Efficiency
Output load regulation
Output line regulation
Load transient response
Output voltage ripple
Start-up
Shutdown
4.1 Input, Output Connections
The TPS564252EVM is provided with input, output connectors and test points as shown in Table 4-1. Figure 4-1
shows connectors and jumpers placement on TPS564252EVM board.
A power supply capable of supplying 4 A must be connected to J1 through a pair of 20-AWG wires. The load
must be connected to J2 through a pair of 20-AWG wires. The maximum load current capability is 4 A. Wire
lengths must be minimized to reduce losses in the wires. Test point TP2 provides a place to monitor the VIN input
voltages with TP6 providing a convenient ground reference. TP3 is used to monitor the output voltage with TP10
as the ground reference.
Figure 4-1. TPS564252EVM Connectors and Jumpers Placement
Table 4-1. Connection and Test Points
REFERENCE DESIGNATOR
FUNCTION
J1
VIN (see Table 1-1 for VIN range)
J2
VOUT, 1.05 V at 4-A maximum
JP1
EN control. Shunt EN to GND to disable
TP1
VIN positive power point
TP2
VIN positive monitor point
TP3
VOUT positive monitor point
TP4
VOUT positive power point
TP5, TP7
GND power point
TP6, TP10, TP12, TP13, TP16
GND monitor point
TP8
Switch node test point
TP9
EN test point
TP11
Test point for loop response measurements
TP14
PGOOD monitor point
TP15
External VCC point for PGOOD pullup
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
5
Test Setup and Results
www.ti.com
4.2 Start-Up Procedure
1. Verify that the jumper at JP1 (Enable control) pins 1 and 2 are covered to shunt EN to GND, disabling the
output.
2. Apply appropriate input voltage to VIN (J1-2) and GND (J1-1).
3. Move the jumper at J1 (Enable control) pin 2 and 1 (EN and GND) to enable the output.
4.3 Efficiency
Figure 4-2 shows the efficiency for the TPS564252EVM at an ambient temperature of 25°C. Figure 4-3 shows
the efficiency for the TPS564257EVM at an ambient temperature of 25°C. Figure 4-4 shows the efficiency for the
TPS564255EVM at an ambient temperature of 25°C.
100%
90%
80%
70%
Efficiency
60%
50%
40%
30%
20%
0.001
Vin=3V
Vin=6V
Vin=12V
0.005
0.02
0.05 0.1 0.2
Iout(A)
0.5
1
2 34
Figure 4-2. TPS564252EVM Efficiency
100%
90%
80%
Efficiency
70%
60%
50%
40%
30%
Vin=3V
Vin=6V
Vin=12V
20%
10%
0
0.001
0.005
0.02
0.05 0.1 0.2
Iout(A)
0.5
1
2 34
Figure 4-3. TPS564257EVM Efficiency
6
Step-Down Converter Evaluation Module
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com
Test Setup and Results
100%
90%
80%
Efficiency
70%
60%
50%
40%
30%
Vin=3V
Vin=6V
Vin=12V
20%
10%
0
0.001
0.005
0.02
0.05 0.1 0.2
Iout(A)
0.5
1
2 34
Figure 4-4. TPS564255EVM Efficiency
4.4 Load Regulation
Figure 4-5 shows load regulation for the TPS564252EVM. Figure 4-6 shows load regulation for the
TPS564257EVM. Figure 4-7 shows load regulation for the TPS564255EVM.
1%
0.8%
Load Regulation
0.6%
0.4%
0.2%
0
-0.2%
Vin=3V
Vin=6V
Vin=12V
Vin=17V
-0.4%
-0.6%
-0.8%
-1%
0.001
0.005
0.02
0.05 0.1 0.2
Iout(A)
0.5
1
2 34
Figure 4-5. TPS564252EVM Load Regulation
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
7
Test Setup and Results
www.ti.com
1%
0.8%
Load Regulation
0.6%
0.4%
0.2%
0
-0.2%
-0.4%
Vin=3V
Vin=6V
Vin=12V
Vin=17V
-0.6%
-0.8%
-1%
0.001
0.005
0.02
0.05 0.1 0.2
Iout(A)
0.5
1
2 34
Figure 4-6. TPS564257EVM Load Regulation
1%
0.8%
Load Regulation
0.6%
0.4%
0.2%
0
-0.2%
-0.4%
Vin=3V
Vin=6V
Vin=12V
Vin=17V
-0.6%
-0.8%
-1%
0.001
0.005
0.02
0.05 0.1 0.2
Iout(A)
0.5
1
2 34
Figure 4-7. TPS564255EVM Load Regulation
8
Step-Down Converter Evaluation Module
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com
Test Setup and Results
4.5 Line Regulation
Figure 4-8 shows line regulation for the TPS564252EVM. Figure 4-9 shows line regulation for the
TPS564257EVM. Figure 4-10 shows line regulation for the TPS564255EVM.
1%
0.8%
Line Regulation
0.6%
0.4%
0.2%
Iout=0A
Iout=4A
0
-0.2%
-0.4%
-0.6%
-0.8%
-1%
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17
Vin(V)
Figure 4-8. TPS564252EVM Line Regulation
1%
0.8%
Line Regulation
0.6%
0.4%
0.2%
0
-0.2%
-0.4%
-0.6%
Iout=0A
Iout=4A
-0.8%
-1%
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17
Vin(V)
Figure 4-9. TPS564257EVM Line Regulation
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
9
Test Setup and Results
www.ti.com
1%
Iout=0A
Iout=4A
0.8%
Line Regulation
0.6%
0.4%
0.2%
0
-0.2%
-0.4%
-0.6%
-0.8%
-1%
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17
Vin(V)
Figure 4-10. TPS564255EVM Line Regulation
4.6 Load Transient Response
Figure 4-11 shows the response to load transient for TPS564252EVM. Figure 4-12 shows the response to load
transient for the TPS564257EVM. Figure 4-13 shows the response to load transient for the TPS564255EVM.
The current steps slew rate is set as 2.5A/μs.
Vout=50mV/div (AC coupled)
Iout=2A/div
200us/div
Figure 4-11. TPS564252EVM Load Transient Response, 10% to 90% (0.4 A to 3.6 A) Load Step
10
Step-Down Converter Evaluation Module
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com
Test Setup and Results
Vout=50mV/div (AC coupled)
Iout=2A/div
200us/div
Figure 4-12. TPS564257EVM Load Transient Response, 10% to 90% (0.3 A to 3.6 A) Load Step
Vout=50mV/div (AC coupled)
Iout=2A/div
200us/div
Figure 4-13. TPS564255EVM Load Transient Response, 10% to 90% (0.3 A to 3.6 A) Load Step
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
11
Test Setup and Results
www.ti.com
4.7 Start-Up
Figure 4-14 shows the TPS564252EVM start-up waveform relative to VIN. The load is 4 A.
Vin=5V/div
EN=5V/div
Vout=500mV/div
4ms/div
Figure 4-14. TPS564252EVM Start-Up Relative to VIN
Figure 4-15 shows the TPS564252EVM start-up waveform relative to enable (EN). The load is 4 A.
Vin=5V/div
EN=2V/div
006
Vout=500mV/div
2ms/div
Figure 4-15. TPS564252EVM Start-Up Relative to EN
12
Step-Down Converter Evaluation Module
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com
Test Setup and Results
4.8 Shutdown
Figure 4-16 shows the TPS564252EVM shut-up waveform relative to VIN. The load is 4 A.
Vin=5V/div
EN=5V/div
Vout=500mV/div
2ms/div
Figure 4-16. TPS564252EVM Shutdown Relative to VIN
Figure 4-17 shows the TPS564252EVM shut-up waveform relative to enable (EN). The load is 4 A.
Vin=5V/div
EN=2V/div
Vout=500mV/div
2ms/div
Figure 4-17. TPS564252EVM Shutdown Relative to EN
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
13
Test Setup and Results
www.ti.com
4.9 Output Voltage Ripple
Figure 4-18 and Figure 4-19 show the TPS564252EVM output voltage ripple. Figure 4-20 shows the
TPS564257EVM output voltage ripple. Figure 4-21 shows the TPS564255EVM output voltage ripple. The output
currents are as indicated.
Vout=20mV/div (AC coupled)
001
SW=5V/div
2us/div
Figure 4-18. TPS564252EVM Output Voltage Ripple, IOUT = 4 A
Vout=20mV/div (AC coupled)
SW=5V/div
40us/div
Figure 4-19. TPS564252EVM Output Voltage Ripple, IOUT = 0.01 A
14
Step-Down Converter Evaluation Module
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com
Test Setup and Results
Vout=20mV/div (AC coupled)
SW=5V/div
2us/div
Figure 4-20. TPS564257EVM Output Voltage Ripple, IOUT = 0.01 A
Vout=20mV/div (AC coupled)
SW=5V/div
40us/div
Figure 4-21. TPS564255EVM Output Voltage Ripple, IOUT = 0.01 A
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
15
Hardware Design Files
www.ti.com
5 Hardware Design Files
5.1 Schematic
Figure 5-1 is the schematic for the TPS564252EVM.
Figure 5-1. TPS564252EVM Schematic Diagram
5.2 PCB Layout
This section provides a description of the TPS56425XEVM, board layout, and layer illustrations.
Figure 5-2, Figure 5-3, and Figure 5-4 show the board layout for the TPS564252EVM. The top layer contains
the main power traces for VIN, VOUT, and ground. Connections for the pins of the TPS564252 and a large
area filled with ground are also on the top layer. Most of the signal traces are also located on the top side. The
input decoupling capacitors C1, C2, and C3 are located as close to the IC as possible. The input and output
connectors, test points, and all of the components are located on the top side. The bottom layer is a ground
plane along with the signal ground copper fill and the feedback trace from the point of regulation to the top of the
resistor divider network. Both the top layer and bottom layer use 2-oz copper thickness.
Figure 5-5 and Figure 5-6 are the TPS564252EVM board top view and bottom view, respectively.
Figure 5-2. TPS564252EVM Top Assembly
16
Step-Down Converter Evaluation Module
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com
Hardware Design Files
Figure 5-3. TPS564252EVM Top Layer
Figure 5-4. TPS564252EVM Bottom Layer
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
17
Hardware Design Files
www.ti.com
Figure 5-5. TPS564252EVM Board (Top View)
Figure 5-6. TPS564252EVM Board (Bottom View)
18
Step-Down Converter Evaluation Module
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com
Hardware Design Files
5.3 Bill of Materials
Table 5-1 presents the bill of materials.
Table 5-1. Bill of Materials
Des
Qty
Description
Part Number
Manufacturer
!PCB1
1
Printed Circuit Board
BSR212A
Any
C1, C2
2
Capacitor, ceramic, 10 µF, 25 V, ±20%, X5R, 0805
GRM21BR61E106MA73L
MuRata
C3, C6
1
Capacitor, ceramic, 0.1 uF, 25 V, ± 10%, X7R, 0603
C0603T104K3RAL7867
KEMET
C4, C5
1
Capacitor, ceramic, 22 µF, 10 V, ±20%, X5R, 0805
GRM21BR61A226ME44L
MuRata
C8
1
Capacitor, ceramic, 0.01 μF, 50 V, ±10%, X7R, 0603 C1608X7R1H103K080AA
TDK
J1, J2
2
Terminal block, 5.08 mm, 2 × 1, Brass, TH
ED120/2DS
On-Shore Technology
JP1, JP2
2
Header, 100 mil, 2 × 1, Tin, TH
PEC02SAAN
Sullins Connector
Solutions
L1
1
Shielded Inductor 1.5 uH, 8 A, 0.0086 Ω, SMD
74437349015
Wurth Elektronik
LBL1
1
Thermal transfer printable labels, 0.650" W × 0.200"
THT-14-423-10
H – 10,000 per roll
Brady
R1
1
Resistor, 20 kΩ, 5%, 0.1 W, AEC-Q200 Grade 0,
0603
CRCW060320K0JNEA
Vishay-Dale
R2
1
Resistor, 30 kΩ, 5%, 0.1 W, AEC-Q200 Grade 0,
0603
CRCW060330K0JNEA
Vishay-Dale
R3
1
Resistor, 51 Ω, 5%, 0.1 W, AEC-Q200 Grade 0,
0603
CRCW060351R0JNEA
Vishay-Dale
R4
1
Resistor, 7.5 kΩ, 1%, 0.1 W, 0603
RC0603FR-077K5L
Yageo
R5, R6
2
Resistor, 10.0 kΩ, 1%, 0.1 W, AEC-Q200 Grade 0,
0603
CRCW060310K0FKEA
Vishay-Dale
SH-JP1,
SH-JP2
2
Shunt, 100 mil, gold plated, black
SNT-100-BK-G
Samtec
TP1, TP4,
TP5, TP7
4
Terminal, turret, TH, double
1502-2
Keystone
TP2, TP3,
TP8, TP9,
TP11,
TP14,
TP15
7
Test point, miniature, red, TH
5000
Keystone
TP6, TP10,
TP12,
TP13,
TP16
5
Test point, miniature, black, TH
5001
Keystone
D1
1
Diode, Zener, 5.6 V, 200 mW, SOD-323
MMSZ5232BS-7-F
Diodes Inc.
U1
1
3-V to 17-V Input, 4-A Synchronous Buck Converter,
TPS564252DRLR
SOT-563
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Texas Instruments
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
19
Additional Information
www.ti.com
6 Additional Information
Trademarks
D-CAP3™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
7 Reference
1. Texas Instruments, TPS56425x 3-V to 17-V Input, 4-A Synchronous Buck Converter in SOT-563 Package
data sheet.
20
Step-Down Converter Evaluation Module
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
www.ti.com
Revision History
8 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision * (December 2022) to Revision A (April 2023)
Page
• Changed the template for Evaluation Module User's Guide ..............................................................................2
• Changed user's guide title.................................................................................................................................. 2
• Changed all figures in Efficiency section............................................................................................................ 6
• Changed all figures in Load Regulation section................................................................................................. 7
• Changed all figures in Line Regulation section.................................................................................................. 9
SLUUCL5A – DECEMBER 2022 – REVISED MAY 2023
Submit Document Feedback
Step-Down Converter Evaluation Module
Copyright © 2023 Texas Instruments Incorporated
21
STANDARD TERMS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or
documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance
with the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License
Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused by
neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have
been altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specifications
or instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality control
techniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM.
User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10)
business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected.
2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or credit
User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty
period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or
replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be
warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
WARNING
Evaluation Kits are intended solely for use by technically qualified,
professional electronics experts who are familiar with the dangers
and application risks associated with handling electrical mechanical
components, systems, and subsystems.
User shall operate the Evaluation Kit within TI’s recommended
guidelines and any applicable legal or environmental requirements
as well as reasonable and customary safeguards. Failure to set up
and/or operate the Evaluation Kit within TI’s recommended
guidelines may result in personal injury or death or property
damage. Proper set up entails following TI’s instructions for
electrical ratings of interface circuits such as input, output and
electrical loads.
NOTE:
EXPOSURE TO ELECTROSTATIC DISCHARGE (ESD) MAY CAUSE DEGREDATION OR FAILURE OF THE EVALUATION
KIT; TI RECOMMENDS STORAGE OF THE EVALUATION KIT IN A PROTECTIVE ESD BAG.
www.ti.com
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software
associated with the kit to determine whether to incorporate such items in a finished product and software developers to write
software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or
otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition
that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.
Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must
operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 or RSS-247
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
2
www.ti.com
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
3.3.2
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
https://www.ti.com/ja-jp/legal/notice-for-evaluation-kits-delivered-in-japan.html
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required to follow the
instructions set forth by Radio Law of Japan, which includes, but is not limited to, the instructions below with respect to EVMs
(which for the avoidance of doubt are stated strictly for convenience and should be verified by User):
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。https://www.ti.com/ja-jp/legal/notice-for-evaluation-kits-for-power-line-communication.html
3.4 European Union
3.4.1
For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive):
This is a class A product intended for use in environments other than domestic environments that are connected to a
low-voltage power-supply network that supplies buildings used for domestic purposes. In a domestic environment this
product may cause radio interference in which case the user may be required to take adequate measures.
3
www.ti.com
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY MATERIALS PROVIDED WITH THE EVM (INCLUDING, BUT NOT
LIMITED TO, REFERENCE DESIGNS AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL
FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT
NOT LIMITED TO ANY EPIDEMIC FAILURE WARRANTY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE
SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS SHALL BE
CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR
INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE
EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR
IMPROVEMENT, REGARDLESS OF WHEN MADE, CONCEIVED OR ACQUIRED.
7.
4
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS. THIS OBLIGATION SHALL APPLY
WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL
THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
www.ti.com
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS OR THE USE OF THE EVMS , REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR
REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING,
OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF
USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI
MORE THAN TWELVE (12) MONTHS AFTER THE EVENT THAT GAVE RISE TO THE CAUSE OF ACTION HAS
OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY USE OF AN EVM PROVIDED
HEREUNDER, INCLUDING FROM ANY WARRANTY, INDEMITY OR OTHER OBLIGATION ARISING OUT OF OR IN
CONNECTION WITH THESE TERMS, , EXCEED THE TOTAL AMOUNT PAID TO TI BY USER FOR THE PARTICULAR
EVM(S) AT ISSUE DURING THE PRIOR TWELVE (12) MONTHS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE
CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
5
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated