Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
Reference
Design
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
TPS6030x Single-Cell to 3-V or 3.3-V, 20-mA Dual Output, High-Efficiency Charge Pump
1 Features
3 Description
•
•
•
•
The TPS6030x devices are a family of switchedvoltage converters designed specifically for spacecritical battery powered applications.
1
•
•
•
•
•
•
Input Voltage Range From 0.9 V to 1.8 V
Regulated 3-V or 3.3-V Output Voltage
Up to 20-mA Output Current
High Power Conversion Efficiency (up to 90%)
Over a Wide Output Current Range, Optimized for
1.2-V Battery Voltage
Additional Output With 2 Times VIN (OUT1)
Device Quiescent Current Less Than 35 µA
Supervisor Included; Open Drain or Push-Pull
Power Good Output
Minimum Number of External Components
– No Inductors Required
– Only Five Small, 1-µF Ceramic Capacitors
Required
Load Isolated From Battery During Shutdown
Micro-Small 10-Pin MSOP (VSSOP) Package
2 Applications
•
•
•
•
•
•
•
Pagers
Battery-Powered Toys
Portable Measurement Instruments
Home-Automation Products
Medical Instruments (Like Hearing Instruments)
Metering Applications Using MSP430 MicroController
Portable Smart Card Readers
Typical Application Schematic
The TPS6030x step-up, regulated charge pumps
generate a 3-V (±4%) or 3.3-V (±4%) output voltage
from a 0.9-V to 1.8-V input voltage (one alkaline,
NiCd, or NiMH battery).
Only five small 1-µF ceramic capacitors are required
to build a complete high efficiency DC-DC charge
pump converter. To achieve the high efficiency over a
wide input voltage range, the charge pump
automatically selects between a 3× or 4× conversion
mode.
Output 1 (OUT1) can deliver a maximum of 40 mA
from a 1-V input, with output 2 (OUT2) not loaded.
OUT2 can deliver a maximum of 20 mA from a 1-V
input, with OUT1 not loaded. Both outputs can be
loaded at the same time, but the total output current
of the first voltage doubler must not exceed 40 mA.
For example, the load at output 1 is 20 mA and the
load at output 2 is 10 mA.
Device Information(1)
PART NUMBER
TPS60300,
TPS60301,
TPS60302,
TPS60303
PACKAGE
VSSOP (10)
BODY SIZE (MAX)
3.05 mm × 4.98 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Alkaline Battery Operating Time
Operating time (hours) with an alkaline battery
(2000 mAh) until power good goes low at IL = 20 mA
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
9
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Description (continued).........................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
4
5
8.1
8.2
8.3
8.4
8.5
8.6
5
5
5
6
6
8
Absolute Maximum Ratings ......................................
ESD Ratings ............................................................
Recommended Operating Conditions.......................
Thermal Information .................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 9
9.1 Overview ................................................................... 9
9.2 Functional Block Diagram ......................................... 9
9.3 Feature Description................................................. 10
9.4 Device Functional Modes........................................ 10
10 Application and Implementation........................ 11
10.1 Application Information.......................................... 11
10.2 Typical Application ............................................... 11
11 Power Supply Recommendations ..................... 18
12 Layout................................................................... 18
12.1 Layout Guidelines ................................................. 18
12.2 Layout Example .................................................... 18
12.3 Power Dissipation ................................................. 19
13 Device and Documentation Support ................. 20
13.1
13.2
13.3
13.4
13.5
13.6
Device Support......................................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
20
20
20
20
20
20
14 Mechanical, Packaging, and Orderable
Information ........................................................... 20
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (March 2001) to Revision B
•
2
Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
TPS60300, TPS60301, TPS60302, TPS60303
www.ti.com
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
5 Description (continued)
The devices operate in the newly developed LinSkip mode. In this operating mode, the device switches
seamlessly from the power saving, pulse-skip mode at light loads, to the low-noise, constant-frequency linearregulation mode, when the output current exceeds the device-specific output current threshold.
A power-good function supervises the output voltage of OUT2 and can be used for power-up and power-down
sequencing. Power good (PG) is offered as either open-drain or push-pull output.
Copyright © 2000–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
3
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
www.ti.com
6 Device Comparison Table
DGS
PACKAGE
MARKING
OUTPUT
CURRENT 1
[mA] (2)
OUTPUT
CURRENT 2
[mA] (3)
OUTPUT
VOLTAGE 1 [V]
OUTPUT
VOLTAGE 2 [V]
FEATURE
TPS60300DGS
ALF
40
20
2 × VIN
3.3
Open-drain powergood output
TPS60301DGS
ALG
40
20
2 × VIN
3
Open-drain powergood output
TPS60302DGS
ALI
40
20
2 × VIN
3.3
Push-pull powergood output
TPS60303DGS
ALK
40
20
2 × VIN
3
Push-pull powergood output
PART NUMBER
(1)
(2)
(3)
(1)
The DGS package is available taped and reeled. Add R suffix to device type (for example, TPS60300DGSR) to order quantities of 2500
devices per reel.
If OUT2 is not loaded.
If OUT1 is not loaded.
7 Pin Configuration and Functions
DGS Package
10-Pin VSSOP
Top View
Pin Functions
PIN
NAME
NO.
I/O
DESCRIPTION
C1+
4
—
Positive pin of the flying capacitor C1F
C1–
2
—
Negative pin of the flying capacitor C1F
C2+
7
—
Positive pin of the flying capacitor C2F
C2–
8
—
Negative pin of the flying capacitor C2F
EN
1
I
GND
9
—
Ground
OUT1
5
O
2 × VIN power output. Bypass OUT1 to GND with the output filter capacitor C(OUT1).
OUT2
6
O
Regulated
3.3-V power output (TPS60300, TPS60302) or 3-V power output (TPS60301, TPS60303), respectively
Bypass OUT2 to GND with the output filter capacitor C(OUT2).
Device-enable input
– EN = Low disables the device. Output and input are isolated in shutdown mode.
– EN = High enables the device.
PG
10
O
Power good detector output. As soon as the voltage on OUT2 reaches about 98% of its nominal value this pin
goes high.
Open-drain output on TPS60300 and TPS60301. A pull-up resistor should be connected between PG and
OUT1 or OUT2.
Push-pull output stage on TPS60302 and TPS60303
VIN
3
I
Supply input. Bypass VIN to GND with a ≥1-µF capacitor.
4
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
TPS60300, TPS60301, TPS60302, TPS60303
www.ti.com
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
8 Specifications
8.1 Absolute Maximum Ratings
Over operating free-air temperature range (unless otherwise noted)
Input voltage (IN to GND) (2)
VIN
VOUT
Output voltage (OUT1,OUT2, EN, PG to GND)
(2)
(1)
MIN
MAX
UNIT
–0.3
2
V
–0.3
V
Voltage (C1+ to GND)
–0.3
V
Voltage (C1– to GND, C2– to GND)
–0.3
V
Voltage (C2+ to GND)
–0.3
V
IOUT
Output current (OUT1)
80
mA
IOUT
Output current (OUT2)
40
mA
TJ
Maximum junction temperature
150
°C
Tstg
Storage temperature
150
°C
(1)
(2)
–55
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The voltage at EN and PG can exceed IN up to the maximum rated voltage without increasing the leakage current drawn by these pins.
8.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
8.3 Recommended Operating Conditions
Over operating free-air temperature range (unless otherwise noted)
MIN
VIN
Input voltage
IOUT(OUT2)
Output current (OUT2)
IOUT(OUT1)
Output current (OUT1)
CIN
Input capacitor
C1F, C2F
Flying capacitors
COUT(1)
Output capacitor
1
COUT(2)
Output capacitor
1
TJ
Operating junction temperature
NOM
0.9
MAX
V
20
mA
40
mA
1
µF
1
Copyright © 2000–2015, Texas Instruments Incorporated
–40
µF
µF
µF
125
Submit Documentation Feedback
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
UNIT
1.8
°C
5
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
www.ti.com
8.4 Thermal Information
TPS6030x
THERMAL METRIC (1)
DGS (VSSOP)
UNIT
10 PINS
RθJA
Junction-to-ambient thermal resistance
156.1
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
53.0
°C/W
RθJB
Junction-to-board thermal resistance
75.5
°C/W
ψJT
Junction-to-top characterization parameter
5.4
°C/W
ψJB
Junction-to-board characterization parameter
74.3
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report (SPRA953).
8.5 Electrical Characteristics
CIN = C1F = C2F = C(OUT1) = C(OUT2) = 1 µF, TC = –40°C to 85°C, VIN = 1 V, V(EN) = VIN (unless otherwise noted)
PARAMETER
VIN
TEST CONDITIONS
IOUT(OUT1)
IOUT(OUT2)
Maximum output current for
TPS60300, TPS60302
IOUT(OUT1)
IOUT(OUT2)
Maximum output current for
TPS60301, TPS60303
VOUT(OUT2)
Output voltage for TPS60300,
TPS60302
VOUT(OUT2)
Output voltage for TPS60301,
TPS60303
VP–P
IQ
Output
voltage ripple
MAX
1.8
VIN ≥ 1.1 V, IOUT(OUT2) = 0 mA, I(PG,1) =
0 mA
40
VIN = 0.9 V, IOUT(OUT2) = 0 mA, I(PG,1) =
0 mA
20
VIN ≥ 1.1 V, IOUT(OUT1) = 0 mA, I(PG,1) =
0 mA
20
VIN = 0.9 V, IOUT(OUT1) = 0 mA, I(PG,1) =
0 mA
10
VIN ≥ 1.1 V, IOUT(OUT2) = 0 mA, I(PG,1) =
0 mA
40
VIN = 0.9 V, IOUT(OUT2) = 0 mA, I(PG,1) =
0 mA
20
VIN ≥ 1 V, IOUT(OUT1) = 0 mA, I(PG,1) = 0
mA
20
VIN = 0.9 V, IOUT(OUT1) = 0 mA, I(PG,1) =
0 mA
12
1.1 V < VIN < 1.8 V, IOUT(OUT1) = 0 mA,
0 < IOUT(OUT2) < 20 mA
3.17
3.30
3.43
0.9 V < VIN < 1.1 V, IOUT(OUT1) = 0 mA,
IOUT(OUT2) < 10 mA
3.17
3.30
3.43
1.0 V < VIN < 1.8 V, IOUT(OUT1) = 0 mA,
0 < IOUT(OUT2) < 20 mA
2.88
3
3.12
VIN > 1.65 V, IOUT(OUT1) = 0 mA,
25 µA < IOUT(OUT2) < 20 mA
2.88
3
3.15
mA
mA
V
V
20
IOUT(OUT1) = 40 mA, IOUT(OUT2) = 0 mA
40
IOUT(OUT) = 0 mA, VIN = 1.8 V
35
70
0.05
2.5
VIN = 1.8 V, V(EN) = 0 V
(1)
VIN = 1.8 V, V(EN) = 0 V, TC = 25°C (1)
Internal switching frequency
VIL(EN)
EN input low voltage
VIN = 0.9 V to 1.8 V
VIH(EN)
EN input high voltage
VIN = 0.9 V to 1.8 V
Ilkg
EN input leakage current
V(EN) = 0 V or VIN or VOUT(OUT2) or
VOUT(OUT1)
LinSkip switching threshold
VIN = 1.25 V
V
mA
IOUT(OUT2) = 20 mA, IOUT(OUT1) = 0 mA
Shutdown supply current
UNIT
mA
OUT1
fOSC
6
TYP
0.9
OUT2
Quiescent current (no-load input
current)
I(SD)
(1)
MIN
Supply voltage range
mVP–P
0.5
470
700
900
0.3 × VIN
0.7 × VIN
0.01
µA
µA
kHz
V
V
0.1
µA
7.5
mA
OUT1 not loaded. If OUT1 is connected to GND through a resistor, leakage current will be increased.
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
TPS60300, TPS60301, TPS60302, TPS60303
www.ti.com
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
Electrical Characteristics (continued)
CIN = C1F = C2F = C(OUT1) = C(OUT2) = 1 µF, TC = –40°C to 85°C, VIN = 1 V, V(EN) = VIN (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
VOUT(OUT2) = 0 V
5
20
50
VOUT(OUT1) = 0 V
2
80
150
Short circuit current
VIN = 1.8 V
Output
leakage
current
VO(OUT1) = 3 V, VOUT(OUT2) = nominal,
EN = 0 V
OUT2
Output load regulation
VIN = 1.25 V, TC = 25°C, 2 mA <
IOUT(OUT2) < 20 mA
Output line regulation
1 V < VIN < 1.65 V; TC = 25°C,
IOUT(OUT) = 10 mA
1
No-load start-up time
Impedance of first charge pump
stage
Start-up performance at OUT2
(minimum start-up load resistance)
VIN ≥ 1.1 V
165
VIN ≥ 1 V
330
VIN = 0.9 V
Start-up performance at OUT1
(minimum start-up load resistance)
VIN = 1 V
MAX
UNIT
mA
µA
0.1
%/mA
0.75
%/V
400
µs
4
Ω
Ω
1000
Ω
500
FOR POWER GOOD COMPARATOR:
V(PG)
Power good trip voltage
VOUT ramping positive
Vhys
Power good trip voltage hysteresis
VOUT ramping negative
VOL
Power good output voltage low
VOUT = 0 V, I(PG) = 1.6 mA
Ilkg
Power good
leakage
current
TPS60300
VOUT = 3.3 V, V(PG) = 3.3 V
TPS60301
VOUT = 3 V, V(PG) = 3 V
VOH
Power good
output
voltage high
TPS60303
IOUT(PG,0)
R(PG,1)
R(PG,0)
Output
current at
power good
(sink)
Output
resistance at
power good
TPS60302
VOUT
V
10%
0.3
0.01
0.1
0.01
0.1
V
µA
3
I(PG) = –5 mA
All devices
V(PG) = 0 V
TPS60302,
TPS60303
V(PG) = VO(OUT2)
All devices
V(PG) = 0 V
Copyright © 2000–2015, Texas Instruments Incorporated
VOUT – 2%
V
2.7
1.6
mA
15
Ω
100
Ω
Submit Documentation Feedback
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
7
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
www.ti.com
8.6 Typical Characteristics
Figure 1. TPS6030x
Quiescent Current vs Input Voltage
8
Submit Documentation Feedback
Figure 2. Switching Frequency vs Input Voltage
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
TPS60300, TPS60301, TPS60302, TPS60303
www.ti.com
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
9 Detailed Description
9.1 Overview
The TPS6030x charge pumps are voltage quadruplers that provide a regulated 3.3-V or 3-V output from a
0.9-V to 1.8-V input. They deliver a maximum load current of 20 mA. Designed specifically for space critical
battery powered applications, the complete converter requires only five external capacitors and enables the
design to use low-cost, small-sized, 1-µF ceramic capacitors. The TPS6030x circuits consist of an oscillator, a
voltage reference, an internal resistive feedback circuit, an error amplifier, two charge pump stages with
MOSFET switches, a shutdown and start-up circuit, and a control circuit.
9.2 Functional Block Diagram
Copyright © 2000–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
9
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
www.ti.com
9.3 Feature Description
9.3.1 Power-Good Detector
The power-good output is an open-drain output on the TPS60300 and TPS60301 or a push-pull output on the
TPS60302 and TPS60303. The PG-output pulls low when the output of OUT2 is out of regulation. When the
output rises to within 98% of regulation, the power-good output goes active high. In shutdown, power-good is
pulled low. In normal operation, an external pullup resistor with the TPS60300 and TPS60301 is typically used to
connect the PG pin to VOUT. The resistor should be in the 100-kΩ to 1-MΩ range. If the PG output is not used, it
should remain unconnected. Output current at PG (TPS60302, TPS60303) will reduce maximum output current
at OUT2.
9.4 Device Functional Modes
9.4.1 Start-up Procedure
The device is enabled when EN is set from logic low to logic high. CP1 will first enter a DC start-up mode during
which the capacitor on OUT1 is charged up to about VIN. After that, it starts switching to boost the voltage further
up to about two times VIN. CP2 will then follow and charge up the capacitor on OUT2 to about the voltage on
OUT1, after that, it will also start switching and boost up the voltage to its nominal value. EN must not exceed the
highest voltage applied to the device.
NOTE
During start-up with VOUT = 0 V, the highest voltage is the input voltage.
9.4.2 Shutdown
Driving EN low disables the converter. This disables all internal circuits, reducing input current to only 0.05 µA.
Leakage current drawn from the output pins OUT1 and OUT2 is a maximum of 1 µA. The device exits shutdown
once EN is set high (see Start-up Procedure). The typical no-load, start-up time is 400 µs. When the device is
disabled, the load is isolated from the input. This is an important feature in battery operated products because it
extends the battery shelf life.
10
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
TPS60300, TPS60301, TPS60302, TPS60303
www.ti.com
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
10 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
The TPS6030x is a switched capacitor voltage converter providing low noise, constant-frequency linear
regulation mode. It supports regulated output voltages of 3 V and 3.3 V from a 0.9-V to 1.8-V input voltage
range.
10.2 Typical Application
Figure 3. Typical Operating Circuit
10.2.1 Design Requirements
The complete charge pump circuitry requires no inductors and only five small 1-µF ceramic capacitors. It is
possible to only use 1-µF capacitors of the same type.
Copyright © 2000–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
11
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
www.ti.com
Typical Application (continued)
10.2.2 Detailed Design Procedure
10.2.2.1 Capacitor Selection
The values of the five external capacitors of the TPS6030x charge pumps are closely linked to the required
output current and the output noise and ripple requirements.
For the maximum output current and best performance, five ceramic capacitors with a minimum value of 1 µF are
recommended. This value is necessary to assure a stable operation of the system due to the linear mode. For
lower currents or higher allowed output voltage ripple, other capacitors can be used. With flying capacitors lower
than 1 µF, the maximum output power will decrease. This means that the device will work in the linear mode with
lower output currents.
The input capacitor improves system efficiency by reducing the input impedance and stabilizing the input current.
The minimum required capacitance of the output capacitor (COUT) that can be selected is 1 µF. Depending on the
maximum allowed output ripple voltage, larger values can be chosen. Table 1 shows capacitor values
recommended for low output voltage ripple operation. A recommendation is given for the smallest size.
Table 1. Recommended Capacitor Values for Low Output Voltage Ripple
Operation
CIN
[µF]
CXF
[µF]
COUT
[µF]
CERAMIC
CERAMIC
CERAMIC
1
1
1
16
0...20
1
1
2.2
10
0…20
1
1
10 // 0.1
6
VIN
[V]
IOUT(OUT2)
[mA]
0.9...1.8
0...20
0.9...1.8
0.9...1.8
VP-P [mV]
At 20 mA / VIN = 1.1 V
Table 2. Recommended Capacitors
MANUFACTURER
PART NUMBER
SIZE
CAPACITANCE
TYPE
Taiyo Yuden
UMK212BJ104MG
LMK212BJ105KG
LMK212BJ225MG
JMK316BJ475KL
805
805
805
1206
0.1 µF
1 µF
2.2 µF
4.7 µF
Ceramic
Ceramic
Ceramic
Ceramic
AVX
0805ZC105KAT2A
1206ZC225KAT2A
805
1206
1 µF
2.2 µF
Ceramic
Ceramic
Table 3 lists the manufacturers of recommended capacitors. However, ceramic capacitors will provide the lowest
output voltage ripple due to their typically lower ESR.
Table 3. Recommended Capacitor Manufacturers
12
MANUFACTURER
CAPACITOR TYPE
Taiyo Yuden
X7R/X5R ceramic
www.t-yuden.com
AVX
X7R/X5R ceramic
www.avxcorp.com
Vishay
X7R/X5R ceramic
www.vishay.com
Kemet
X7R/X5R ceramic
www.kemet.com
TDK
X7R/X5R ceramic
www.component.tdk.com
Submit Documentation Feedback
INTERNET
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
TPS60300, TPS60301, TPS60302, TPS60303
www.ti.com
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
10.2.2.2 Output Filter Design
The power-good output is capable of driving light loads up to 5 mA (see Figure 4). Therefore, the output
resistance of the power-good pin, in addition with an output capacitor, can be used as an RC-filter.
Figure 4. TPS60302, TPS60303 Push-Pull Power-Good Output-Stage as Filtered Supply
Due to R(PG,1), an output filter can easily be formed with an output capacitor (CPG). Cut-off frequency is given by:
1
ƒc =
2pR(PG,1)C(PG)
(1)
and ratio VOUT / VIN is :
V(PG,1)
VO(OUT2)
1
=
(
1 + 2pƒR(PG,1)C(PG)
2
)
(2)
with R(PG,1) = 15 Ω, C(PG) = 0.1 µF and f = 600 kHz (at nominal switching frequency)
V(PG,1)
VO(OUT2)
= 0.175
(3)
Load current sourced by power-good output reduces maximum output current at OUT2. During start-up (power
good going high) current charging C(PG) will discharge C(OUT2). Therefore, C(PG) must not be larger than 0.1
C(OUT2) or the device will not start. By charging C(PG) through C(OUT2), the output voltage at OUT2 will decrease. If
the capacitance of C(PG) is to large, the circuit will detect power bad. The power-good output will go low and
discharge C(PG). Then the cycle starts again. Figure 5 shows a configuration with an LC-post filter to further
reduce output ripple and noise.
Copyright © 2000–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
13
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
www.ti.com
Figure 5. LC-Post Filter
Table 4. Recommended Values for Lowest Output Voltage Ripple
VIN
[V]
IO(OUT2)
[mA]
CIN[µF]
CXF[µF]
COUT[µF]
CERAMIC
CERAMIC
CERAMIC
0.9...1.8
20
1
1
1
0.9...1.8
20
1
1
0.9...1.8
20
1
1
0.9...1.8
20
1
1
CP[µF]
CERAMIC
VP(OUT)
VP-P[mV]
0.1
0.1 (X7R)
16
1
0.1
1 // 0.1 (X7R)
12
1
1
0.1 (X7R)
14
10
1
1 // 0.1 (X7R)
3
LP[µH]
Figure 6. Application With MSP430; PG as Supply for Analog Circuits
14
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
TPS60300, TPS60301, TPS60302, TPS60303
www.ti.com
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
10.2.3 Application Curves
Figure 7. TPS60300, TPS60302
Efficiency vs Output Current
Figure 8. TPS60301, TPS60303
Efficiency vs Output Current
Figure 9. TPS60300
Supply Current vs Output Current
Figure 10. TPS60300, TPS60302
Output Voltage (OUT2) vs Output Current (OUT2)
Figure 11. TPS60301, TPS60303
Output Voltage (OUT2) vs Output Current (OUT2)
Figure 12. TPS60300, TPS60302
Output Voltage (OUT1) vs Output Current (OUT1)
Copyright © 2000–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
15
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
16
www.ti.com
Figure 13. TPS60300, TPS60302
Output Voltage (OUT2) vs Input Voltage
Figure 14. TPS60300, TPS60302
Output Voltage (OUT2) vs Input Voltage
Figure 15. TPS6030x
Output Voltage (OUT1) vs Input Voltage
Figure 16. TPS60300, TPS60302
Output Voltage (OUT2) vs Free-Air Temperature
Figure 17. TPS60301, TPS60303
Output Voltage (OUT2) vs Free-Air Temperature
Figure 18. TPS6030x
Output Voltage Ripple (OUT2)
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
TPS60300, TPS60301, TPS60302, TPS60303
www.ti.com
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
Figure 19. TPS60300, TPS60302
Minimum Input Voltage vs Output Current
Figure 20. TPS60301, TPS60303
Minimum Input Voltage vs Output Current
Figure 21. Start-Up Timing Enable
Figure 22. Load Transient Response
Figure 23. Line Transient Response
Copyright © 2000–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
17
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
www.ti.com
11 Power Supply Recommendations
The TPS6030x devices have no special requirements for their input power supply. The output currents of the
input power supply must be rated according to the supply voltage, output voltage, and output current of the
TPS6030x.
12 Layout
12.1 Layout Guidelines
All capacitors must be soldered as close as possible to the IC. A PCB layout proposal for a two-layer board is
shown in Figure 24. Care has been taken to connect all capacitors as close as possible to the circuit to achieve
optimized output voltage ripple performance. The bottom layer is not shown in Figure 24. It only consists of a
ground-plane with a single track between the two vias that can be seen in the left part of the top layer.
12.2 Layout Example
Figure 24. Recommended PCB Layout for TPS6030x (Top Layer)
18
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
TPS60300, TPS60301, TPS60302, TPS60303
www.ti.com
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
12.3 Power Dissipation
The thermal resistance of the unsoldered package is RθJA = 294°C/W. Soldered on the EVM, a typical thermal
resistance of RθJA(EVM) = 200°C/W was measured.
The thermal resistance can be calculated as shown in Equation 4.
T - TA
RqJA = J
PD
where
•
•
•
TJ is the junction temperature.
TA is the ambient temperature.
PD is the power that needs to be dissipated by the device.
(4)
The maximum power dissipation can be calculated as shown in Equation 5.
PD = VIN × IIN – VOUT × IOUT = VIN(max) × [(3 × IOUT + I(SUPPLY)] – VOUT × IOUT
(5)
The maximum power dissipation happens with maximum input voltage and maximum output current:
At maximum load the supply current is approximately 2 mA.
PD = 1.8 V × (3 × 20 mA + 2 mA) – 3.3 V × 20 mA = 46 mW.
(6)
With this maximum rating and the thermal resistance of the device on the EVM, the maximum temperature rise
above ambient temperature can be calculated as shown in Equation 7.
ΔTJ = RθJA × PD = 200°C/W × 46 mW = 10°C
(7)
This means that internal dissipation increases TJ by 10°C.
The junction temperature of the device must not exceed 125°C.
This means the IC can easily be used at ambient temperatures as seen in Equation 8.
TA = TJ(max) – ΔTJ = 125°C – 10°C = 115°C
Copyright © 2000–2015, Texas Instruments Incorporated
(8)
Submit Documentation Feedback
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
19
TPS60300, TPS60301, TPS60302, TPS60303
SLVS302B – DECEMBER 2000 – REVISED OCTOBER 2015
www.ti.com
13 Device and Documentation Support
13.1 Device Support
13.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
13.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 5. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
TPS60300
Click here
Click here
Click here
Click here
Click here
TPS60301
Click here
Click here
Click here
Click here
Click here
TPS60302
Click here
Click here
Click here
Click here
Click here
TPS60303
Click here
Click here
Click here
Click here
Click here
13.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
13.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
13.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
13.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
20
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: TPS60300 TPS60301 TPS60302 TPS60303
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
TPS60300DGS
ACTIVE
VSSOP
DGS
10
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
ALF
Samples
TPS60300DGSR
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
ALF
Samples
TPS60301DGS
ACTIVE
VSSOP
DGS
10
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
ALG
Samples
TPS60301DGSR
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
ALG
Samples
TPS60302DGS
ACTIVE
VSSOP
DGS
10
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
ALI
Samples
TPS60302DGSR
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
ALI
Samples
TPS60303DGSR
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
ALK
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
