Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
TPS6205x 800-mA Synchronous Step-Down Converter
1 Features
3 Description
•
The TPS6205x devices are a family of high-efficiency
synchronous step-down DC-DC converters that are
ideally suited for systems powered from a 1- or 2-cell
Li-Ion battery or from a 3- to 5-cell NiCd, NiMH, or
alkaline battery.
1
•
•
•
•
•
•
•
•
•
•
•
High-Efficiency Synchronous Step-Down
Converter With up to 95% Efficiency
12-µA Quiescent Current (Typical)
2.7-V to 10-V Operating Input Voltage Range
Adjustable Output Voltage Range: 0.7 V to 6 V
Fixed Output Voltage Options Available With
1.5 V, 1.8 V, and 3.3 V
Synchronizable to External Clock: Up to 1.2 MHz
High-Efficiency Over a Wide Load Current Range
in Power-Save Mode
100% Maximum Duty Cycle for Lowest Dropout
Low-Noise Operation in Forced FixedFrequency PWM Operation Mode
Internal Softstart
Overtemperature and Overcurrent Protected
Available in 10-Pin Micro-Small Outline
Package MSOP
2 Applications
•
•
•
•
Cellular Phones
Organizers, PDAs, and Handheld PCs
Low-Power DSP Supplies
Digital Cameras and Hard Disks
The TPS6205x devices are synchronous pulse width
modulation (PWM) converters with integrated N- and
P-channel power MOSFET switches. Synchronous
rectification increases efficiency and reduces external
component count. To achieve highest efficiency over
a wide load current range, the converter enters a
power-saving pulse frequency modulation (PFM)
mode at light load currents. Operating frequency is
typically 850 kHz, allowing the use of small inductor
and capacitor values. The device can be
synchronized to an external clock signal in the range
of 600 kHz to 1.2 MHz. For low noise operation, the
converter can be programmed into forced-fixed
frequency in PWM mode. In shutdown mode, the
current consumption is reduced to less than 2 µA.
The TPS6205x devices are available in the 10-pin
(DGS) micro-small outline package (MSOP) and
operates over a free air temperature range of –40°C
to 85°C.
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
VSSOP (10)
3.00 mm × 3.00 mm
TPS62050
TPS62051
TPS62052
TPS62054
TPS62056
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
4 Typical Application Schematic
Efficiency vs Output Current
1
8
SW
VIN
9
L1 = 10 µH
VO = 1.5 V / 800 mA
90
80
5
FB
EN
70
TPS62052
Ci = 10 µF
100
6
PG
LBI
4
Co = 22 µF
7
2
SYNC
GND
3
LBO
PGND
10
Efficiency – %
VI = 3.3 V to 10 V
60
50
40
30
20
10
0
0.01
VI = 7.2 V,
VO = 5 V,
SYNC = L
0.1
1
10
100
1k
IO – Output Current – mA
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
9
Features ..................................................................
Applications ...........................................................
Description .............................................................
Typical Application Schematic.............................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
3
4
8.1
8.2
8.3
8.4
8.5
8.6
4
4
4
4
5
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 7
9.1 Overview ................................................................... 7
9.2 Functional Block Diagram ......................................... 7
9.3 Feature Description................................................... 8
9.4 Device Functional Modes........................................ 10
10 Application and Implementation........................ 12
10.1 Application Information.......................................... 12
10.2 Typical Applications .............................................. 12
10.3 System Examples ................................................. 19
11 Power Supply Recommendations ..................... 20
12 Layout................................................................... 20
12.1 Layout Guidelines ................................................. 20
12.2 Layout Example .................................................... 20
13 Device and Documentation Support ................. 22
13.1
13.2
13.3
13.4
13.5
13.6
Device Support......................................................
Related Links ........................................................
Community Resource............................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
22
22
22
22
22
22
14 Mechanical, Packaging, and Orderable
Information ........................................................... 22
5 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (June 2011) to Revision F
•
Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision D (October 2003) to Revision E
Page
•
Changed to Revision E, June 2011........................................................................................................................................ 1
•
Changed formatting. ............................................................................................................................................................... 1
•
Changed "goes active high" to "floats" in Terminal Functions table, row PG, description. .................................................... 3
•
Changed "becomes active" to "floats" in last paragraph of Power Good Comparator section. ........................................... 10
2
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
www.ti.com
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
6 Device Comparison Table
PACKAGED DEVICES
OUTPUT VOLTAGE
LBI/LBO FUNCTIONALITY
TPS62050DGS
Adjustable 0.7 V to 6 V
Standard
TPS62051DGS
Adjustable 0.7 V to 6 V
Enhanced
TPS62052DGS
1.5 V
Standard
TPS62054DGS
1.8 V
Standard
TPS62056DGS
3.3 V
Standard
PLASTIC MSOP (1) (DGS)
(1)
The DGS packages are available taped and reeled. Add an R suffix to the device type (that is, TPS62050DGSR) to order quantities of
2500 devices per reel.
7 Pin Configuration and Functions
DGS Package
10-Pin VSSOP
Top View
VIN
LBO
GND
PG
FB
1
10
2
9
3
8
4
7
5
6
PGND
SW
EN
SYNC
LBI
Pin Functions
PIN
NAME
NO.
I/O
DESCRIPTION
EN
8
I
Enable. A logic high enables the converter, logic low forces the device into shutdown mode, reducing the supply
current to less than 2 µA.
FB
5
I
Feedback pin for the fixed output voltage option. For the adjustable version, an external resistive divider is
connected to this pin. The internal voltage divider is disabled for the adjustable version.
GND
3
I
Ground
LBI
6
I
Low battery input.
LBO
2
O
Open-drain low battery output. Logic low signal indicates a low battery voltage.
PG
4
O
Power good comparator output. This is an open-drain output. A pullup resistor must be connected between PG
and VOUT. The output floats when the output voltage is greater than 95% of the nominal value.
PGND
10
I
Power ground. Connect all power grounds to this pin.
SW
9
O
Connect the inductor to this pin. This pin is the switch pin and connected to the drain of the internal power
MOSFETS.
SYNC
7
I
Input for synchronization to the external clock signal. This input can be connected to an external clock or pulled to
GND or VI. When an external clock signal is applied, the device synchronizes to this external clock and the device
operates in fixed PWM mode. When the pin is pulled to either GND or VI, the internal oscillator is used and the
logic level determines if the device operates in fixed PWM or PWM/PFM mode.
SYNC = HIGH: Low-noise mode enabled, fixed-frequency PWM operation is forced.
SYNC = LOW (GND): Power save mode enabled, PFM/PWM mode enabled.
VIN
1
I
Supply voltage input.
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
3
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
8 Specifications
8.1 Absolute Maximum Ratings
Over operating free-air temperature range unless otherwise noted (1)
VI
MIN
MAX
UNIT
Supply voltage
–0.3
11
V
Voltage at EN, SYNC
–0.3
VI
V
Voltage at LBI, FB, LBO, PG
–0.3
7
V
Voltage at SW
–0.3
11 (2)
V
IO
Output current
850
mA
TJ
Maximum junction temperature
150
°C
TA
Operating free-air temperature
85
°C
300
°C
150
°C
–40
Lead temperature 1.6 mm (1/16 inch) from case for 10 seconds
Tstg
(1)
(2)
Storage temperature
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The voltage at the SW pin is sampled in PFM mode 15 µs after the PMOS has switched off. During this time the voltage at SW is limited
to 7 V maximum. Therefore, the output voltage of the converter is limited to 7 V maximum.
8.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (1)
±2000
Charged device model (CDM), per JEDEC specification JESD22-C101,
all pins (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
8.3 Recommended Operating Conditions
MIN
Supply voltage at VI
NOM
2.7
UNIT
10
Voltage at PG, LBO
V
6
Maximum output current
Operating junction temperature
(1)
MAX
–40
V
800 (1)
mA
125
°C
Assuming no thermal limitation
8.4 Thermal Information
TPS6205x
THERMAL METRIC (1)
DGS (VSSOP)
UNIT
10 PINS
RθJA
Junction-to-ambient thermal resistance
154
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
50.6
°C/W
RθJB
Junction-to-board thermal resistance
73.6
°C/W
ψJT
Junction-to-top characterization parameter
5.1
°C/W
ψJB
Junction-to-board characterization parameter
72.4
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
www.ti.com
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
8.5 Electrical Characteristics
VI = 7.2 V, VO = 3.3 V, IO = 300 mA, EN = VI, TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
VI
Input voltage
I(Q)
Operating quiescent current
I(SD)
Shutdown current
IQ(LBI)
Quiescent current with enhanced LBI comparator
version.
10
V
IO = 0 mA, SYNC = GND, VI = 7.2 V
2.7
12
20
µA
EN = GND
1.5
5
EN = GND, TA = 25°C
1.5
3
EN = VI, LBI = GND, TPS62051 only
5
µA
µA
ENABLE
VIH
EN high level input voltage
VIL
EN low level input voltage
1.3
V
0.3
EN trip point hysteresis
100
Ilkg
EN input leakage current
EN = GND or VIN, VI = 7.2 V
I(EN)
EN input current
0.6 V ≤ V(EN) ≤ 4 V
V(UVLO)
Undervoltage lockout threshold
0.01
V
mV
0.2
µA
2
µA
1.6
V
POWER SWITCH
RDS(ON)
RDS(ON)
P-channel MOSFET ON-resistance
VI ≥ 5.4 V; IO = 300 mA
400
650
VI = 2.7 V; IO = 300 mA
600
850
1
µA
1200
1400
mA
VI ≥ 5.4 V; IO = 300 mA
300
450
VI = 2.7 V; IO = 300 mA
450
550
P-channel MOSFET leakage current
VDS = 10 V
P-channel MOSFET current limit
VI = 7.2V, VO = 3.3 V
N-channel MOSFET ON-resistance
N-channel MOSFET leakage current
1000
VDS = 6 V
1
mΩ
mΩ
µA
POWER GOOD OUTPUT, LBI, LBO
V(PG)
Power good trip voltage
Vml –2%
Power good delay time
VOL
VO ramping positive
50
VO ramping negative
200
PG, LBO output low voltage
V(FB) = 0.8 × VO nominal, I(sink) = 1 mA
PG, LBO output leakage current
V(FB) = VO nominal, V(LBI) = VI
0.01
Minimum supply voltage for valid power good, LBO
signal
V(LBI)
Low-battery input trip voltage
Low-battery input hysteresis
Ilkg(LBI)
LBI leakage current
µs
0.3
V
0.25
µA
2.3
Input voltage falling
V
1.21
Low-battery input trip point accuracy
V(LBI,HYS)
V
V
1.5%
15
mV
0.01
0.1
µA
850
1000
kHz
1200
kHz
OSCILLATOR
fS
Oscillator frequency
600
f(SYNC)
Synchronization range
600
VIH
SYNC high-level input voltage
1.5
VIL
SYNC low-level input voltage
Ilkg
SYNC input leakage current
SYNC = GND or VIN
V
0.01
SYNC trip point hysteresis
0.3
V
0.1
µA
100
Duty cycle of external clock signal
20%
mV
90%
OUTPUT
VO
Adjustable output voltage
TPS62050, TPS62051
V(FB)
Feedback voltage
TPS62050, TPS62051
0.5
FB leakage current
TPS62050, TPS62051
0.02
Feedback voltage tolerance
TPS62050, TPS62051 VI = 2.7 V to 10 V, 0 mA < IO < 600 mA
Copyright © 2002–2015, Texas Instruments Incorporated
0.7
–3%
6
V
0.1
µA
V
3%
Submit Documentation Feedback
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
5
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
Electrical Characteristics (continued)
VI = 7.2 V, VO = 3.3 V, IO = 300 mA, EN = VI, TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
Fixed output voltage
tolerance (1)
TEST CONDITIONS
MIN
–3%
3%
TPS62054
VI = 2.7 V to 10 V, 0 mA < IO < 600 mA
–3%
3%
TPS62056
VI = 3.75 V to 10 V, 0 mA < IO < 600 mA
–3%
3%
700
1000
1300
UNIT
kΩ
Line regulation
VO = 3.3 V, VI = 5 V to 10 V, IO = 600 mA
5.2
mV/V
Load regulation
VI = 7.2 V; IO = 10 mA to 600 mA
0.0045
%/mA
VI = 5 V; VO = 3.3 V; IO = 300 mA
93%
VI = 3.6 V; VO = 2.5 V; IO = 200 mA
93%
Efficiency
Duty cycle range for main switches
100%
Minimum ton time for main switch
100
ns
Shutdown temperature
145
°C
1
ms
IO = 200 mA, VI = 5 V, Vo = 3.3 V,
Co = 22 µF, L = 10 µH
Start-up time
(1)
MAX
VI = 2.7 V to 10 V, 0 mA < IO < 600 mA
Resistance of internal voltage divider for fixed-voltage
versions
η
TYP
TPS62052
The worst case RDS(ON) of the PMOS in 100% mode for an input voltage of 3.3 V is 0.75 Ω. This value can be used to determine the
minimum input voltage if the output current is less than 600 mA with the TPS62056.
8.6 Typical Characteristics
900
2.7 V
Switching Frequency − kHz
890
3.6 V
880
870
5V
860
850
7.2 V
840
830
820
810
800
−40
−20 0
20
40
60
80
TA − Free-Air Temperature − °C
100
Figure 1. Switching Frequency vs Free-Air Temperature
6
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
www.ti.com
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
9 Detailed Description
9.1 Overview
The TPS6205x family of devices are synchronous step-down converters that operate with a 850-kHz fixedfrequency pulse width modulation (PWM) at moderate to heavy load currents and enters the power save mode at
light load current.
During PWM operation, the converter uses a unique fast response voltage mode control scheme with input
voltage feed forward to achieve good line and load regulation with the use of small ceramic input and output
capacitors. At the beginning of each clock cycle initiated by the clock signal (S), the P-channel MOSFET switch
is turned on and the inductor current ramps up until the voltage comparator trips and the control logic turns the
switch off. Also the switch is turned off by the current limit comparator if the current limit of the P-channel switch
is exceeded. After the dead time preventing current shoot through, the N-channel MOSFET rectifier is turned on
and the inductor current ramps down. The next cycle is initiated by the clock signal again, turning off the Nchannel rectifier and turning on the P-channel switch.
The error amplifier as well as the input voltage determines the rise time of the saw tooth generator; therefore,
any change in input voltage or output voltage directly controls the duty cycle of the converter giving a very good
line and load transient regulation.
9.2 Functional Block Diagram
VI
Current Limit Comparator
+
Undervoltage
Lockout
Bias Supply
–
REF
SYNC
+
Soft Start
I(AVG) Comparator
REF
–
V
I
850 kHz
Oscillator
V(COMP)
P-Channel
Power MOSFET
Comparator
+
Saw Tooth
Generator
S
R
–
Driver
Shoot-Through
Logic
Control
Logic
Comparator High
Comparator Low
Comparator High2
SW
N-Channel
Power MOSFET
Load Comparator
+
SKIP Comparator
PG
–
Error Amp
Comparator High
+
LBO
Compensation
Comparator Low
Comparator Low2
VREF = 0.5 V
–
R1
–
+
_
R2
See Note
+
1.21 V
EN
FB
LBI
PGND
GND
NOTE: For the adjustable versions (TPS62050, TPS62051 devices), the internal feedback driver is disabled and the
FB pin is directly connected to the GM amplifier.
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
7
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
9.3 Feature Description
9.3.1 Enable and Overtemperature Protection
A logic low on EN forces the TPS6205x devices into shutdown. In shutdown, the power switch, drivers, voltage
reference, oscillator, and all other functions are turned off. The supply current is reduced to less than 2 µA in the
shutdown mode. When the device is in thermal shutdown, the bandgap is forced to stay on even if the device is
set into shutdown by pulling EN to GND. As soon as the temperature drops below the threshold, the device
automatically starts again.
If an output voltage is present when the device is disabled, which could be an external voltage source or super
cap, the reverse leakage current is specified under Electrical Characteristics. Pulling the enable pin high starts up
the TPS6205x devices with the soft-start as described in Soft-Start. If the EN pin is connected to any voltage
other than VI or GND, an increased leakage current of typically 10 µA and up to 20 µA can occur.
VIN
VIN
0 µA for VEN < 0.6 V
Typically 0.3 µA to 5 µAfor VEN < 4 V
5V
Vt = 0.7 V
EN
Enable to Internal Circuitry
Figure 2. Internal Circuit of the ENABLE Pin
The EN pin can be used in a pushbutton configuration as shown in Figure 3. The external resistor to GND must
be capable of sinking 0.3 µA with a minimum voltage drop of 1.3 V to keep the system enabled when both
switches are open. When the ON-button is pressed, the device is enabled and the current through the external
resistor keeps the voltage level high to ensure that the device stays on when the ON-button is released. When
the OFF-button is pressed, the device is switched off and the current through the external resistor is zero. The
device therefore stays off even when the OFF-button is released.
VIN
TPS6205x
ON
EN
OFF
0.3 µA, min
R >1.3 V/0.3 µA
Figure 3. Pushbutton Configuration for the EN-Pin
9.3.2 Low-Battery Detector (Standard Version)
The low-battery output (LBO) is an open-drain type which goes low when the voltage at the low battery input
(LBI) falls below the trip point of 1.21 V ±1.5%. The voltage at which the low-battery warning is issued is adjusted
with a resistive divider as shown in Figure 5. TI recommends the sum of the resistors R1 and R2 to be in the
100-kΩ to 1-MΩ range for high-efficiency at low output current. An external pullup resistor at LBO can either be
connected to OUT, or any other voltage rail in the voltage range of 0 V to 6 V. During start-up, the LBO output
signal is invalid for the first 500 µs. LBO is high impedance when the device is disabled. If the low-battery
comparator function is not used, connect LBI to ground. The low-battery detector is disabled when the device is
disabled. Leave the LBO pin unconnected, or connect to GND when not used.
8
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
www.ti.com
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
Feature Description (continued)
9.3.3 ENABLE / Low-Battery Detector (Enhanced Version) TPS62051 Only
The TPS62051 device offers an enhanced LBI functionality to provide a precise, user-programmable
undervoltage shutdown. No additional supply voltage supervisor (SVS) is needed to provide this function.
When the enable (EN) pin is pulled high, only the internal bandgap voltage reference is switched on to provide a
reference source for the LBI comparator. As long as the voltage at LBI is less than the LBI trip point, all other
internal circuits are shut down, reducing the supply current to 5 µA. As soon as input voltage at LBI rises above
the LBI trip point of 1.21 V, the device is completely enabled and starts switching.
VIN
Bandgap
ENABLE
Enable to Internal Circuitry
LBI
Comparator
LBI
LBO
Figure 4. Block Diagram of ENABLE / LBI Functionality for TPS62051
The logic level of the LBO pin is not defined for the first 500 µs after EN is pulled high.
When the enhanced LBI is used to supervise the battery voltage and shut down the TPS62051 at low input
voltages, the battery voltage rises again when the current drops to zero. The implemented hysteresis on the LBI
pin may not be sufficient for all types of batteries. Figure 5 shows how an additional external hysteresis can be
implemented.
1
8
VIN
SW
EN
FB
6
Ci = 10 µF
L1 = 10 µH
VO = 2.5 V / 600 mA
5
R3
R4
R1
C(ff) =
6.8 pF
TPS62051
R5
1 Cell Li-lon
9
7
R6
LBI
SYNC
GND
3
PG 4
LBO
R2
2
Co = 22 µF
PGND
10
R7
Figure 5. Enhanced LBI With Increased Hysteresis
A MATHCAD® file to calculate R7 can be downloaded from the product folder on the TI web.
9.3.4 Undervoltage Lockout
The undervoltage lockout (UVLO) circuit prevents the device from misoperation at low input voltages. The circuit
prevents the converter from turning on the switch or rectifier MOSFET under undefined conditions.
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
9
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
Feature Description (continued)
9.3.5 Power Good Comparator
The power good (PG) comparator has an open-drain output capable of sinking typically 1 mA. The PG function is
only active when the device is enabled (EN = high). When the device is disabled (EN = low), the PG pin is pulled
to GND.
The PG output is only valid after a 250-µs delay after the device is enabled and the supply voltage is greater
than 2.7 V. Power good is low during the first 250 µs after shutdown and in shutdown.
The PG pin floats high when the output voltage exceeds typically 98.5% of its nominal value. Leave the PG pin
unconnected, or connect it to GND when not used.
9.3.6 Synchronization
If no clock signal is applied, the converter operates with a typical switching frequency of 850 kHz. It is possible to
synchronize the converter to an external clock within a frequency range from 600 kHz to 1200 kHz. The device
automatically detects the rising edge of the first clock and synchronizes to the external clock. If the clock signal is
stopped, the converter automatically switches back to the internal clock and continues operation. The switchover
is initiated if no rising edge on the SYNC pin is detected for a duration of four clock cycles. Therefore, the
maximum delay time can be 8.3 µs if the internal clock has its minimum frequency of 600 kHz. During this time,
there is no clock signal available. The device stops switching until the internal circuitry is switched to the internal
clock source.
When the device is switched between internal synchronization and external synchronization during operation, the
output voltage may show transient overshoot or undershoot during switchover. The voltage transients are
minimized by using 850 kHz as an initial external frequency, and changing the frequency slowly (>1 ms) to the
value desired. The voltage drop at the output when the device is switched from external synchronization to
internal synchronization can be reduced by increasing the output capacitor value.
If the device is synchronized to an external clock, the power-save mode is disabled and the device stays in
forced PWM mode.
Connecting the SYNC pin to the GND pin enables the power-save mode. The converter operates in the PWM
mode at moderate to heavy loads and in the PFM mode during light loads maintaining high-efficiency over a wide
load current range.
9.4 Device Functional Modes
9.4.1 Soft-Start
The TPS6205x device have an internal soft-start circuit that limits the inrush current during start-up. This
prevents possible voltage drops of the input voltage if a battery or a high impedance power source is connected
to the input of the TPS6205x devices.
The soft-start is implemented as a digital circuit increasing the switch current in steps of 200 mA, 400 mA, 800
mA and then the typical switch current limit of 1.2 A. Therefore the start-up time mainly depends on the output
capacitor and load current. Typical start-up time with a 22-µF output capacitor and a 200-mA load current is 1
ms.
9.4.2 Constant Frequency Mode Operation (SYNC = HIGH)
In the constant frequency mode, the output voltage is regulated by varying the duty cycle of the PWM signal in
the range of 100% to 10%. Connecting the SYNC pin to a voltage greater than 1.5 V forces the converter to
operate permanently in the PWM mode even at light or no load currents. The advantage is the converter
operates with a fixed switching frequency that allows simple filtering of the switching frequency for noise sensitive
applications. In this mode, the efficiency is lower compared to the power-save mode during light loads (see
Figure 7). The N-MOSFET of the devices stays on even when the current into the output drops to zero. This
prevents the device from going into discontinuous mode. The device transfers unused energy back to the input.
Therefore, there is no ringing at the output that usually occurs in the discontinuous mode. The duty cycle range
in constant frequency mode is 100% to 10%.
10
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
www.ti.com
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
Device Functional Modes (continued)
It is possible to switch from forced PWM mode to the power-save mode during operation by pulling the SYNC pin
low. The flexible configuration of the SYNC pin during operation of the device allows efficient power management
by adjusting the operation of the TPS6205x devices to the specific system requirements.
9.4.3 Power-Save Mode Operation (SYNC = LOW)
As the load current decreases, the converter enters the power-save mode operation. During power-save mode
the converter operates with reduced switching frequency in PFM and with a minimum quiescent current to
maintain high-efficiency. Whenever the average output current goes below the skip threshold, the converter
enters the power-save mode. The average current depends on the input voltage. The current is 100 mA at low
input voltages and up to 200 mA with maximum input voltage. The average output current must be less than the
threshold for at least 32 clock cycles (tcy) to enter the power-save mode. During the power save mode, the output
voltage is monitored with a comparator. When the output voltage falls below the comparator low threshold set to
0.8% above VO nominal, the P-channel switch turns on. The P-channel switch turns off as the peak switch
current of typically 200 mA is reached. The N-channel rectifier turns on and the inductor current ramps down. As
the inductor current approaches zero, the N-channel rectifier is turned off and the switch is turned on starting the
next pulse. When the output voltage can not be reached with a single pulse, the device continues to switch with
its normal operating frequency, until the comparator detects the output voltage to be 1.6% above the nominal
output voltage. The converter wakes up again when the output voltage falls below the comparator low threshold.
This control method reduces the quiescent current to typically to 12 µA and the switching frequency to a
minimum achieving the highest converter efficiency. Having these skip current thresholds 0.8% and 1.6% above
the nominal output voltage gives a lower absolute voltage drop during a load transient as anticipated with a
standard converter operating in this mode.
9.4.4 100% Duty Cycle Low Dropout Operation
The TPS6205x devices offer the lowest possible input to output voltage difference while still maintaining
operation with the use of the 100% duty cycle mode. In this mode, the P-channel switch is constantly turned on.
This is particularly useful in battery-powered applications to achieve longest operation time by taking full
advantage of the whole battery voltage range. The minimum input voltage to maintain regulation depends on the
load current and output voltage and can be calculated using Equation 1.
VI(min) = VO(max) + IO(max) ´ (RDS(ON)(max) + RL )
IO (max) = Maximum output current plus inductor ripple current
RDS(ON)(max) = Maximum P-Channel switch resistance
RL = DC resistance of the inductor
VO(max) = Nominal output voltage plus maximum output voltage tolerance
(1)
9.4.5 No Load Operation
If the converter operates in the forced PWM mode and there is no load connected to the output, the converter
regulates the output voltage by allowing the inductor current to reverse for a short period of time.
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
11
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
10 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
The TPS6205x family of devices are high-efficiency synchronous step-down DC-DC converters ideally suited for
systems powered from a 1-cell or 2-cell Li-Ion battery or from a 3-cell to 5-cell NiCd, NiMH, or alkaline battery.
10.2 Typical Applications
10.2.1 Standard Circuit for Adjustable Version
WE PD 744 777 10
VI
1
R5
130 kW
Ci = 10 mF
TDK
C3216X5R1A106M
8
VIN
SW
EN
FB
5
R3
1M
R4
1M
TPS62050
6
R6
100 kW
VO = 5 V
9 L1 = 10 mH
R1 =
820 kW
4
LBI
PG
7
C(ff) = 6.8 pF
Co = 22 mF
2
SYNC
GND
3
LBO
Taiyo Yuden
JMK316BJ226ML
R2 = 91 kW
PGND
10
Quiescent Current Measurements and Efficiency Were Taken
With: R5 = Open, R4 = Open, LBI Connected to GND.
Figure 6. Standard Circuit for Adjustable Version
10.2.1.1 Design Requirements
The design guidelines provide a component selection to operate the adjustable device within the Recommended
Operating Conditions.
Table 1. Bill of Materials for Adjustable Version
12
REFERENCE
PART NUMBER
VALUE
Ci
C3216X5R1A106M
10 µF
MANUFACTURER
TDK
Co
JMK316BJ226ML
22 µF
Taiyo Yuden
L1
WE PD 74477710
10 µH
Wurth
IC1
TPS62050
-
Texas Instruments
R1
generic metal film resistor;
tolerance 1%
820 kΩ (depending on desired
output voltage)
—
R2
generic metal film resistor;
tolerance 1%
91 kΩ (depending on desired
output voltage)
—
R3, R4
generic metal film resistor;
tolerance 1%
1 MΩ
—
R5
generic metal film resistor;
tolerance 1%
130 kΩ
—
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
www.ti.com
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
Typical Applications (continued)
Table 1. Bill of Materials for Adjustable Version (continued)
REFERENCE
PART NUMBER
VALUE
MANUFACTURER
R6
generic metal film resistor;
tolerance 1%
100 kΩ
—
C(ff)
generic ceramic capacitor; COG
6.8 pF
—
10.2.1.2 Detailed Design Procedure
All graphs have been generated using the circuit as shown unless otherwise noted. For output voltages other
than 5 V, the fixed-voltage versions were used. The resistors R1, R2, and the feed forward capacitor (Cff) are
removed and the feedback pin is directly connected to the output.
V
O –R2
V + V FB R1 ) R2
V FB + 0.5V
R1
+
R2
O
R2
V FB
ǒ Ǔ
(2)
Table 2. Values for Resistor Combinations and Feedback Capacitors
NOMINAL OUTPUT VOLTAGE
EQUATION
POSSIBLE RESISTOR COMBINATION TYPICAL FEEDBACK CAPACITOR
0.7 V
R1 = 0.4 × R2
R1 = 270 k, R2 = 680 k
C(ff) = 22 pF
1.2 V
R1 = 1.4 × R2
R1 = 510 k, R2 = 360 k (1.21 V)
C(ff) = 6.8 pF
1.5 V
R1 = 2 × R2
R1 = 300 k, R2 = 150 k (1.5 V)
C(ff) = 6.8 pF
1.8 V
R1 = 2.6 × R2
R1 = 390 k, R2 = 150 k (1.80 V)
C(ff) = 6.8 pF
2.5 V
R1 = 4 × R2
R1 = 680 k, R2 = 169 k (2.51 V)
C(ff) = 6.8 pF
3.3 V
R1 = 5.6 × R2
R1 = 560 k, R2 = 100 k (3.3 V)
C(ff) = 6.8 pF
5V
R1 = 9 × R2
R1 = 820 k, R2 = 91 k (5 V)
C(ff) = 6.8 pF
10.2.1.2.1 Inductor Selection
A 10-µH minimum inductor must be used with the TPS6205x family of devices. Values larger than 22 µH or
smaller than 10 µH may cause stability problems due to the internal compensation of the regulator. After
choosing the inductor value of typically 10 µH, two additional inductor parameters must be considered: the
current rating of the inductor and the DC resistance. The DC resistance of the inductance directly influences the
efficiency of the converter. Therefore, an inductor with lowest DC resistance must be selected for highest
efficiency. To avoid saturation of the inductor, the inductor must be rated at least for the maximum output current
plus half the inductor ripple current which is calculated using Equation 3.
V
1* O
V
I
DI L + V
I L(max) + I (max) ) DIL
O
O
2
L f
f = Switching frequency (850 kHz typical)
L = Inductor value
∆IL = Peak-to-peak inductor ripple current
IL(max) = Maximum inductor current
(3)
The highest inductor current occurs at maximum VIN . A more conservative approach is to select the inductor
current rating just for the maximum switch current of the TPS6205x device, which is 1.4 A maximum. See
Table 3 for inductors that have been tested for operation with the TPS6205x devices.
Table 3. Inductors
MANUFACTURER
TYPE
INDUCTANCE
DC RESISTANCE
SATURATION CURRENT
TDK
SLF7032T100M1R4SLF7032T220M96SLF7045T100M1R3SLF7045T100MR90
10 µH ±20%
22 µH ±20%
10 µH ±20%
22 µH ±20%
53 mΩ ±20%
110 mΩ ±20%
36 mΩ ±20%
61 mΩ ±20%
1.4 A
0.96 A
1.3 A
0.9 A
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
13
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
Table 3. Inductors (continued)
MANUFACTURER
Sumida
Coilcraft
Wuerth
TYPE
INDUCTANCE
DC RESISTANCE
SATURATION CURRENT
CDR74B
10 µH
70 mΩ
1.65 A
CDR74B
22 µH
130 mΩ
1.12 A
CDH74
10 µH
49 mΩ
1.8 A
CDH74
22 µH
110 mΩ
1.23 A
1A
CDR63B
10 µH
140 mΩ
CDRH4D28
10 µH
128 mΩ
1A
CDRH5D28
10 µH
48 mΩ
1.3 A
CDRH5D18
10 µH
92 mΩ
1.2 A
DT3316P-153
15 µH
60 mΩ
1.8 A
DT3316P-223
22 µH
84 mΩ
1.5 A
WE-PD 744 778 10
10 µH
72 mΩ
1.68 A
1.84 A
WE-PD 744 777 10
10 µH
49 mΩ
WE-PD 744 778 122
22 µH
190 mΩ
1.07A
WE-PD 744 777 122
22 µH
110 mΩ
1.23 A
10.2.1.2.2 Output Capacitor Selection
The output capacitor must have a minimum value of 22 µF. For best performance, a low ESR ceramic output
capacitor is needed.
For completeness, use Equation 4 to calculate the RMS ripple current.
V
1– O
V
I
1
I
+V
RMS(Co)
O
L f
2 Ǹ3
(4)
The overall output ripple voltage is the sum of the voltage spike caused by the output capacitor ESR plus the
voltage ripple caused by charge and discharging the output capacitor, as shown in Equation 5.
V
1* O
V
I
1
DV + V
)R
O
O
ESR
L f
8 Co f
(5)
ǒ
Ǔ
The highest output voltage ripple occurs at the highest input voltage VI.
10.2.1.2.3 Input Capacitor Selection
Because the buck converter has a pulsating input current, a low ESR input capacitor is required for best input
voltage filtering and minimizing the interference with other circuits caused by high input voltage spikes. The input
capacitor must have a minimum value of 10 µF and can be increased without any limit for better input voltage
filtering. The input capacitor must be rated for the maximum input ripple current calculated as:
Ǹ ǒ Ǔ
V
I
+ I (max)
RMS
O
O
V
I
V
1* O
V
I
(6)
The worst-case RMS ripple current occurs at D = 0.5 and is calculated as: IRMS = IO/2. Ceramic capacitors have a
good performance because of their low ESR value and they are less sensitive to voltage transients compared to
tantalum capacitors. Place the input capacitor as close as possible to the input pin of the IC for best
performance.
14
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
www.ti.com
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
Table 4. Capacitors
MANUFACTURER
Taiyo Yuden
Kemet
TDK
(1)
PART NUMBER
SIZE
VOLTAGE
CAPACITANCE
TYPE
JMK212BJ106MG
0805
6.3 V
10 µF
Ceramic
JMK316BJ106ML
1206
6.3 V
10 µF
Ceramic
JMK316BJ226ML
1206
6.3 V
22 µF
Ceramic
LMK316BJ475ML
1206
10 V
4.7 µF (1)
Ceramic
EMK316BJ475ML
1206
16 V
4.7 µF (1)
Ceramic
EMK325BJ106KN-T
1210
16 V
10 µF
Ceramic
C1206C106M9PAC
1206
6.3 V
10 µF
Ceramic
C2012X5R0J106M
0805
6.3 V
10 µF
Ceramic
C3216X5R0J226M
1206
6.3 V
22 µF
Ceramic
C3216X5R1A106M
1206
10 V
10 µF
Ceramic
Connect two in parallel.
10.2.1.2.4 Feedforward Capacitor
The feedforward capacitor (C(ff) shown in Figure 5) improves the performance in SKIP mode. The comparator is
faster; therefore, there is less voltage ripple at the output in SKIP mode. Use the values listed in Table 2. Larger
values decrease stability in fixed frequency PWM mode. If the TPS6205x devices are only operated in fixed
frequency PWM mode, the feedforward capacitor is not needed.
1.6%
0.8%
VO, nominal
–1.6%
t
Figure 7. Power-Save Mode Output Voltage Thresholds
The converter enters the fixed frequency PWM mode again as soon as the output voltage falls below the
comparator low 2 threshold set to 1.6% below VO, nominal.
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
15
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
10.2.1.3 Application Curves
100
100
VI = 3.5 V
VI = 5.5 V
90
90
VI = 6.5 V
80
60
50
VI = 8.4 V
40
VI = 10 V
30
10
0.1
1
10
100
SYNC = L
VO = 3.3 V
TA = 25°C
0
0.01
1k
0.1
1
10
100
1k
IL − Load Current − mA
IL − Load Current − mA
Figure 8. TPS62050 Efficiency vs Load Current
Figure 9. TPS62056 Efficiency vs Load Current
100
VI = 5.5 V
90
90
80
80
70
60
VI = 5 V
50
40
VI = 7.2 V
30
VI = 7.2 V
60
VI = 8.4 V
50
VI = 10 V
40
30
20
SYNC = L
VO = 1.5 V
TA = 25°C
VI = 10 V
10
0
0.01
VI = 6.5 V
70
VI = 3.3 V
Efficiency − %
Efficiency − %
VI = 10 V
40
10
VI = 2.7 V
0.1
1
10
100
SYNC = H
VO = 5 V
TA = 25°C
20
10
0
0.01
1k
0.1
1
10
100
1k
IL − Load Current − mA
IL − Load Current − mA
Figure 10. TPS62052 Efficiency vs Load Current
Figure 11. TPS62050 Efficiency vs Load Current
100
100
VI = 2.7 V
VI = 3.5 V
90
80
90
70
Efficiency − %
VI = 7.2 V
60
50
40
VI = 10 V
30
10
0.1
1
10
100
VI = 5 V
60
VI = 7.2 V
50
40
VI = 10 V
30
SYNC = H
VO = 3.3 V
TA = 25°C
20
0
0.01
VI = 3.3 V
80
VI = 5 V
70
Efficiency − %
VI = 7.2 V
50
20
100
16
60
30
SYNC = L
VO = 5 V
TA = 25°C
20
0
0.01
VI = 5 V
70
Efficiency − %
Efficiency − %
80
VI = 7.2 V
70
SYNC = H
VO = 1.5 V
TA = 25°C
20
10
1k
0
0.01
0.1
1
10
100
1k
IL − Load Current − mA
IL − Load Current − mA
Figure 12. TPS62056 Efficiency vs Load Current
Figure 13. TPS62052 Efficiency vs Load Current
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
www.ti.com
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
VI = 7.2 V, VO = 3.3 V
VI = 7.2 V
VO = 3.3 V
IO = 800 mA
Output Voltage
2 V/div
2 V/div
10 mV/div
10 mV/div
Output Voltage
IO = 20 mA
Voltage at SW Pin
Voltage at SW Pin
1ms/div
10ms/div
Figure 15. Output Voltage Ripple in PWM Mode
Figure 14. Output Voltage Ripple in Skip Mode
VI = 5 V
VO = 3.3 V
VI = 4.5 V to 5.5 V to 4.5 V
50 mV/div
Load Step = 60 mA to 540 mA
VO
1 ms/div
500 mA/div
10 mV/div
500 mv/div
Output Voltage
50 ms/div
Figure 16. Line Transient Response in PWM Mode
Figure 17. Load Transient Response
Voltage at SW Pin
5 V/div
5 V/div
EN
VI = 5 V
IO = 100 mA
VO
5 ms/div
Figure 18. V(SWITCH) and IL
(Inductor Current) in Skip Mode
Copyright © 2002–2015, Texas Instruments Incorporated
II
VI = 5 V
RL = 2.7 W
100 mA/div
100 mA/div
1 V/div
Inductor Current
200 ms/div
Figure 19. Start-up Timing
Submit Documentation Feedback
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
17
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
10.2.2 Standard Circuit for Fixed Voltage Version
VI = 2.7 V to 10 V
1
R5
VIN
SW
EN
FB
L1 = 10 µH
9
5
8
R3
VO = 1.8 V / 600 mA
R4
TPS62054
Ci = 10 µF
4
6
R6
PG
LBI
7
LBO
SYNC
GND
3
Co = 22 µF
2
PGND
10
Figure 20. Standard Circuit for Fixed Voltage Version
10.2.2.1 Design Requirements
The design guidelines provide a component selection to operate the device within the Recommended Operating
Conditions.
Table 5. Bill of Materials for Fixed Voltage Versions
18
REFERENCE
PART NUMBER
VALUE
Ci
C3216X5R1A106M
10 µF
MANUFACTURER
TDK
Co
JMK316BJ226ML
22 µF
Taiyo Yuden
L1
WE PD 74477710
10 µH
Wurth
IC1
TPS62054
—
Texas Instruments
R3, R4
generic metal film resistor; tolerance
1%
1 MΩ
—
R5
generic metal film resistor; tolerance
1%
130 kΩ
—
R6
generic metal film resistor; tolerance
1%
100 kΩ
—
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
www.ti.com
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
10.2.2.2 Detailed Design Procedure
Connect the feedback pin (FB) to the pad of the output capacitor. The pullup resistors for pins PG and LBO are
typically chosen as 100 kΩ each. The input capacitor must be placed as close to the VIN pin as possible.
10.2.2.3 Application Curves
100
100
VI = 2.7 V
VI = 2.7 V
90
90
80
80
70
VI = 3.3 V
60
Efficiency − %
Efficiency − %
70
VI = 5 V
50
VI = 7.2 V
40
VI = 10 V
30
60
40
VI = 10 V
SYNC = L
VO = 1.8 V
TA = 25°C
10
0.1
VI = 7.2 V
50
30
20
0
0.01
VI = 3.3 V
VI = 5 V
1
10
100
SYNC = H
VO = 1.8 V
TA = 25°C
20
10
0
0.01
1k
0.1
1
10
100
1k
IL − Load Current − mA
IL − Load Current − mA
Figure 21. TPS62054 Efficiency vs Load Current in PFM
Mode
Figure 22. TPS62054 Efficiency vs Load Current in PWM
Mode
10.3 System Examples
The TPS62050 device is used to generate an output voltage of 0.7 V. With such low output voltages, the inductor
discharges very slowly. This leads to a high-output voltage ripple in power-save mode (SYNC = GND).
Therefore, TI recommends using a larger output capacitor to keep the output ripple low. With an output capacitor
of 47 µF, the output voltage ripple is less than 40 mVPP.
VI = 2.7 V to 7 V
1
SW
VIN
VO = 0.7 V / 600 mA
R1 = 270 kΩ
8
EN
Ci = 10 µF
9 L1 = 10 µH
FB
C(ff) = 22 pF
5
TPS62050
6
4
LBI
PG
7
R2 = 680 kΩ
Co = 47 µF
2
SYNC
GND
3
LBO
PGND
10
Figure 23. Converter for 0.7-V Output Voltage
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
19
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
11 Power Supply Recommendations
The TPS6205x family of devices has no special requirements for its power supply. The output current of the
power supply must be rated according to the supply voltage, output voltage, and output current of the TPS6205x
devices.
12 Layout
12.1 Layout Guidelines
All capacitors must be soldered as close as possible to the IC.
For information on the PCB layout, see the user's guide, SLVU081.
Keep the feedback track as short as possible. Any coupling to the FB pin may cause additional output voltage
ripple. The feedback connection from the output capacitor C4 to R1 of the feedback network is made directly
from the pad of C4 as shown by the via. The connection of GND with PGND is done similarly directly at the
PGND pad of C4. Uncritical signals like the connections for LBI, LBO, and PG are not shown for better
readability.
12.2 Layout Example
PGND
VI
to GND
VO
to R1
C4
Figure 24. Layout
20
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
www.ti.com
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
Layout Example (continued)
VI = 2.7V to 10V
C1
1
8
VIN
SW
9
L1 = 10 uH
R1
FB
5
C4
R2
TPS62050
7
3
C3
EN
10µF
6
VO = 0.7V to 6V
LBI
SYNC
GND
22µF
PG 4
2
LBO
PGND
10
Figure 25. Associated Layout Schematic
Copyright © 2002–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
21
TPS62050, TPS62051, TPS62052, TPS62054, TPS62056
SLVS432F – SEPTEMBER 2002 – REVISED JUNE 2015
www.ti.com
13 Device and Documentation Support
13.1 Device Support
TPS6205xEVM User's Guide, SLVU081
13.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
13.2 Related Links
Table 6 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to sample or buy.
Table 6. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
TPS62050
Click here
Click here
Click here
Click here
Click here
TPS62051
Click here
Click here
Click here
Click here
Click here
TPS62052
Click here
Click here
Click here
Click here
Click here
TPS62054
Click here
Click here
Click here
Click here
Click here
TPS62056
Click here
Click here
Click here
Click here
Click here
13.3 Community Resource
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
13.4 Trademarks
E2E is a trademark of Texas Instruments.
MATHCAD is a registered trademark of Mathsoft Incorporated.
All other trademarks are the property of their respective owners.
13.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
13.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
22
Submit Documentation Feedback
Copyright © 2002–2015, Texas Instruments Incorporated
Product Folder Links: TPS62050 TPS62051 TPS62052 TPS62054 TPS62056
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
TPS62050DGS
ACTIVE
VSSOP
DGS
10
80
RoHS & Green
Call TI | NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
BFM
Samples
TPS62050DGSG4
ACTIVE
VSSOP
DGS
10
80
RoHS & Green
Call TI
Level-1-260C-UNLIM
-40 to 85
BFM
Samples
TPS62050DGSR
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green
Call TI | NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
BFM
Samples
TPS62050DGSRG4
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green
Call TI
Level-1-260C-UNLIM
-40 to 85
BFM
Samples
TPS62051DGS
ACTIVE
VSSOP
DGS
10
80
RoHS & Green NIPDAU | NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
BGB
Samples
TPS62051DGSR
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green NIPDAU | NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
BGB
Samples
TPS62052DGS
ACTIVE
VSSOP
DGS
10
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
BGC
Samples
TPS62052DGSR
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
BGC
Samples
TPS62054DGS
ACTIVE
VSSOP
DGS
10
80
RoHS & Green NIPDAU | NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
BGE
Samples
TPS62054DGSR
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green NIPDAU | NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
BGE
Samples
TPS62056DGS
ACTIVE
VSSOP
DGS
10
80
RoHS & Green NIPDAU | NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
BGG
Samples
TPS62056DGSG4
ACTIVE
VSSOP
DGS
10
80
RoHS & Green
Level-1-260C-UNLIM
-40 to 85
BGG
Samples
TPS62056DGSR
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green NIPDAU | NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
BGG
Samples
TPS62056DGSRG4
ACTIVE
VSSOP
DGS
10
2500
RoHS & Green
Level-1-260C-UNLIM
-40 to 85
BGG
Samples
NIPDAU
NIPDAU
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of