Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
TPS657051, TPS657052
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
TPS65705x PMU for Embedded Camera Module
1 Features
3 Description
•
•
•
The TPS65705x devices are small power
management units targeted for embedded camera
module or other portable low-power consumer-end
equipments. The device contains two highly efficient
step-down converters, a low dropout linear regulator,
and additional supporting functions. The 2.25-MHz
step-down converter enters a low-power mode at light
load for maximum efficiency across the widest
possible range of load currents. For low-noise
applications, the device can be forced into fixedfrequency PWM mode using the MODE pin. The
device allows the use of small inductors and
capacitors to achieve a small sized solution. The
TPS65705x provides an output current of up to
400 mA on both DC-DC converters and integrates
one 200-mA LDO with different output settings. The
LDO operates with an input voltage range from 1.7 V
to 6 V, thus allowing it to be supplied from the output
of the step-down converter or directly from the
system voltage.
1
•
•
•
•
•
•
•
•
Two 400-mA Step-Down Converters
Up to 92% Efficiency
VIN Range for DC-DC Converter
From 3.3 V to 6 V
2.25-MHz Fixed-Frequency Operation
Power Save Mode at Light Load Current
Output Voltage Accuracy in PWM Mode ±1.5%
100% Duty Cycle for Lowest Dropout
180° Out-of-Phase Operation
1 General Purpose 200-mA LDO
VIN Range for LDO From 1.7 V to 6.0 V
Available in a 16-Ball DSBGA (WCSP) With 0.5mm Pitch
2 Applications
•
•
•
Digital Cameras
Portable Media Players
Handheld Equipment
The TPS65705x comes in a small 16-pin wafer chip
scale package (WCSP) with 0.5-mm ball pitch.
Device Information(1)
PART NUMBER
PACKAGE
TPS657051
DSBGA (16)
TPS657052
BODY SIZE (NOM)
2.08 mm × 2.08 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Application Circuit
VCC
TPS 657051/52
2.2 μH
L1
VIN1
10 mF
MODE
DCDC1
EN1
400 mA
FB1
Vout1
10uF
PGND
CLK0°
2.25 MHz
Oscillator
VIN2
EN2
CLK180°
L2
2.2 μH
Vout2
DCDC2
400 mA
FB2
10 mF
PGND
VLDO
VINLDO
ENLDO
LDO
200 mA
Vout3
2.2 mF
AGND
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS657051, TPS657052
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Options.......................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
4
7.1
7.2
7.3
7.4
7.5
7.6
7.7
4
4
5
5
5
7
7
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Dissipation Ratings ...................................................
Typical Characteristics ..............................................
Detailed Description ............................................ 12
8.1 Overview ................................................................. 12
8.2 Functional Block Diagram ....................................... 12
8.3 Feature Description................................................. 12
8.4 Device Functional Modes........................................ 15
9
Application and Implementation ........................ 16
9.1 Application Information............................................ 16
9.2 Typical Application ................................................. 16
10 Power Supply Recommendations ..................... 18
11 Layout................................................................... 19
11.1 Layout Guidelines ................................................. 19
11.2 Layout Example .................................................... 19
12 Device and Documentation Support ................. 20
12.1
12.2
12.3
12.4
12.5
12.6
Device Support......................................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
20
20
20
20
20
20
13 Mechanical, Packaging, and Orderable
Information ........................................................... 20
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (February 2010) to Revision A
Page
•
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section .................................................................................................. 1
•
Changed footnote error for Device Options table................................................................................................................... 3
2
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
TPS657051, TPS657052
www.ti.com
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
5 Device Options
(1)
PART NO. (1)
SIZE FOR DSBGA VERSION
OPTIONS
I2C
TPS657051
D = 2076 µm ± 25 µm
E = 2076 µm ± 25 µm
DC-DC1 3.3 V FIX, DC-DC2 1.8 V FIX
DC-DC CONVERTERS 400 mA,
LDO VOUT 3 V FIX, 200 mA
N/A
TPS657052
D = 2076 µm ± 25 µm
E = 2076 µm ± 25 µm
DC-DC1 3.3 V FIX, DC-DC2 1.8 V FIX
DC-DC CONVERTERS 400 mA,
LDO VOUT 2.8 V FIX, 200 mA
N/A
For the most current package and ordering information, see the Mechanical, Packaging, and Orderable Information section at the end of
this document, or see the TI website at www.ti.com.
6 Pin Configuration and Functions
TPS657051 YZH Package
16-Pin DSBGA
Top View
2075um
VLDO
AGND
VIN
VIN
LDO
LDO
VCC
EN1
EN2
VIN2
EN
LDO
LDO
MODE
L2
VIN1
2075um
A1
B1
L1
C1
PGND
PGND
1 D1
FB1
FB2
D2
D3
PGND
PGND
2
2 D4
TPS657052 YZH Package
16-Pin DSBGA
Top View
2075um
VIN2
VIN
VIN
LDO
LDO
AGND
EN2
EN1
VLDO
A1
VIN1
B1
L2
EN
EN
LDO
LDO
MODE
2075um
VCC
L1
C1
PGND
PGND
2
2 D4
FB2
FB1
D3
D2
PGND
PGND
11 D1
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
Submit Documentation Feedback
3
TPS657051, TPS657052
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
www.ti.com
Pin Functions
PIN
NO.
I/O
NAME
DESCRIPTION
A1
VLDO
O
Output voltage from LDO
A2
AGND
—
Analog ground
A3
VINLDO
I
Input voltage pin for LDO
A4 (1)
VCC
I
Supply Input for internal reference, has to be connected to VIN1/ VIN2
B1 (2)
VIN1
I
Input voltage pin for buck converter 1
B2
EN1
I
Actively high enable input voltage for buck converter 1
B3
EN2
I
Actively high enable input voltage for buck converter 2
B4 (2)
VIN2
I
Input voltage pin for buck converter 2
C1
L1
O
Switch output from buck converter 1
C2
ENLDO
I
Actively high enable input voltage for LDO
C3
MODE
I
Set low to enable Power Save Mode. Pulling this PIN to high forces the device to operate in
PWM mode over the whole load range.
C4
L2
O
Switch output from buck converter 2
D1
PGND1
—
Power ground
D2
FB1
I
Feedback input from buck converter 1
D3
FB2
I
Feedback input from buck converter 2
D4
PGND2
—
(1)
(2)
Power ground
VCC must be the highest input for the device to function correctly.
VIN1/VIN2 must be connected to VCC.
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
Input voltage on all pins except A/PGND pins with respect to AGND
–0.3
7
V
Voltage on pin VLDO1 with respect to AGND
–0.3
3.6
V
L1, VLDO1, VINLDO1, PGND
600
mA
AGND
20
mA
All other pins
3
mA
Current
Continuous total power dissipation
See Dissipation Ratings
Operating free-air temperature, TA
–40
Maximum junction temperature, TJ
Storage temperature, Tstg
–65
85
°C
125
°C
150
°C
7.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
4
Electrostatic
discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001
(1)
Charged device model (CDM), per JEDEC specification JESD22-C101 (2)
±2000
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
TPS657051, TPS657052
www.ti.com
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
3.3
MAX
UNIT
VIN1/2
Input voltage for step-down converter DCDC1 and DCDC2
IOUTDCDC1/2
Output current at L
6
L
Inductor at L
1.5
VINLDO
Input voltage for LDO
1.7
ILDO
Output current at LDO
CINDCDC1/2
Input Capacitor at VIN1 and VIN2
4.7
COUTDCDC1/2
Output Capacitor at VOUT1, VOUT2
4.7
CINLDO
Input Capacitor at VINLDO
2.2
COUTLDO
Output Capacitor at VLDO
2.2
TA
Operating ambient temperature
–40
85
°C
TJ
Operating junction temperature
–40
125
°C
2.2
V
400
mA
4.7
µH
6.0
V
200
mA
µF
10
22
µF
µF
µF
7.4 Thermal Information
TPS65705x
THERMAL METRIC
(1)
YZH (DSBGA)
UNIT
16 PINS
RθJA
Junction-to-ambient thermal resistance
75
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
22
°C/W
RθJB
Junction-to-board thermal resistance
26
°C/W
ψJT
Junction-to-top characterization parameter
0.2
°C/W
ψJB
Junction-to-board characterization parameter
24
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
7.5 Electrical Characteristics
Unless otherwise noted: VIN1 = VIN2 = VINLDO = 3.6 V, L = LQMP21P 2.2 µH, COUTDCDCx = 10 µF, COUTLDO = 2.2 µF, TA = –40°C
to +85°C
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
DCDC1 and DCDC2 enabled, IOUT = 0 mA,
MODE =0
(PFM mode), LDO disabled
40
µA
DCDC1 or DCDC2 enabled, IOUT = 0 mA,
MODE =0
(PFM mode), LDO disabled
25
µA
DCDC1 or DCDC2 enabled, IOUT = 0 mA.
MODE =1 (forced PWM mode), LDO disabled
4
mA
Operating quiescent current LDO
DCDC1 and DCDC2 disabled, LDO enabled.
IOUT = 0 mA
25
37
µA
Shutdown current
DCDC1, DCDC2, and LDO disable
5
12
µA
VCC
V
0.4
V
0.1
μA
6
V
Operating quiescent current DCDCx
IQ
ISD
DIGITAL PINS (EN1, EN2, ENLDO, MODE)
VIH
High-level input voltage for EN1,
EN2, ENLDO, MODE
VIL
Low-level input voltage for EN1,
EN2, ENLDO, MODE
ILKG
Input leakage current
1.2
EN1, EN2, ENLDO, MODE tied to GND
or VIN = VIN2
0.01
STEP-DOWN CONVERTERS
VIN1
Input voltage for DCDC1
3.3
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
Submit Documentation Feedback
5
TPS657051, TPS657052
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
www.ti.com
Electrical Characteristics (continued)
Unless otherwise noted: VIN1 = VIN2 = VINLDO = 3.6 V, L = LQMP21P 2.2 µH, COUTDCDCx = 10 µF, COUTLDO = 2.2 µF, TA = –40°C
to +85°C
PARAMETER
VIN2
TEST CONDITIONS
MIN
Input voltage for DCDC2
TYP
3.3
MAX
UNIT
6
V
2.25
V
Internal undervoltage lockout
threshold
VIN1 = VIN2 falling
Internal undervoltage lockout
threshold hysteresis
VIN1 = VIN2 rising
120
High-side MOSFET ON-resistance
VIN1 = VIN2 = 3.6 V
350
750
mΩ
Low-side MOSFET ON-resistance
VIN1 = VIN2 = 3.6 V
350
600
mΩ
ILIMF
Forward current limit
3.3 V ≤ VIN1 = VIN2 ≤ 6 V
650
770
mA
IOUTDCDC1/2
DCDC1/DCDC2 output current
VIN1 = VIN2 > 3.3 V , L = 2.2 µH
400
mA
2.48
MHz
UVLO
2.15
2.2
mV
POWER SWITCH
RDS(ON)
550
OSCILLATOR
fSW
Oscillator frequency
2.03
2.25
OUTPUT
VOUT1
DCDC1 default output voltage
VIN1 = VIN2 ≥ 3.3 V
3.3
V
VOUT2
DCDC2 default output voltage
VIN1 = VIN2 ≥ 3.3 V
1.8
V
IFB
FB pin input current
DC-DC converter disabled
DC output voltage accuracy (1)
VIN1 = VIN2 = 3.3 V to 6 V, +1% voltage
positioning active; PFM operation, 0 mA < IOUT
< IOUTMAX
DC output voltage accuracy
VIN1 = VIN2 = 3.3 V to 6 V, PWM operation,
0 mA < IOUT < IOUTMAX
DC output voltage load regulation
PWM operation
0.5
%/A
tStart
Start-up time
Time from active EN to Start switching
200
µs
tRamp
VOUT ramp time
Time to ramp from 5% to 95% of VOUT
250
µs
RDIS
Internal discharge resistor at L1 or
L2
(TPS657051 Only)
DCDC1 or DCDC2 disabled
VOUT
0.1
+1%
–1.5%
250
µA
+3%
+1.5%
400
600
Ω
THERMAL PROTECTION SEPARATELY FOR DCDC1, DCDC2 AND LDO1
TSD
Thermal shutdown
Increasing junction temperature
150
°C
Thermal shudown hysteresis
Decreasing junction temperature
30
°C
VLDO, LOW DROPOUT REGULATOR
VINLDO
Input voltage range for LDO
VLDO
TPS657051 LDO default output
voltage (2)
3
V
VLDO
TPS657052 LDO default output
voltage (3)
2.8
V
IO
Output current for LDO
ISC
LDO short circuit current limit
VLDO = GND
Dropout voltage at LDO
IO = 200 mA
Output voltage accuracy for LDO
IO = 100 mA, VOUT = 2.8V
–2%
+2%
Line regulation for LDO
VINLDO = VLDO + 0.5 V (min. 1.7 V) to 6 V,
IO = 50 mA
–1%
1%
Load regulation for LDO
IO = 1 mA to 200 mA for LDO
–1%
1%
PSRR
Power supply rejection ratio
fNOISE ≤ 10 kHz, COUT ≥ 2.2 µf Vin = 5 V,
Vout = 2.8 V, IOUT = 100 mA
Vn
Ouput noise voltage
Vout = 2.8 V, BW = 10Hz to 100kHz
(1)
(2)
(3)
6
1.7
340
6
400
V
200
mA
550
mA
200
mV
50
dB
160
µV RMS
In Power Save Mode (PFM), the internal reference voltage is 1.01 × Vref.
VINLDO > 3 V
VINLDO > 2.8 V
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
TPS657051, TPS657052
www.ti.com
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
Electrical Characteristics (continued)
Unless otherwise noted: VIN1 = VIN2 = VINLDO = 3.6 V, L = LQMP21P 2.2 µH, COUTDCDCx = 10 µF, COUTLDO = 2.2 µF, TA = –40°C
to +85°C
PARAMETER
TEST CONDITIONS
MIN
tRamp
VOUT ramp time
Internal soft-start when LDO is enabled; Time to
ramp from 5% to 95% of VOUT
RDIS
Internal discharge resistor at VLDO
LDO disabled
TYP
MAX
UNIT
200
250
400
µs
550
Ω
7.6 Dissipation Ratings
PACKAGE
RθJA
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
TPS657051/52 (1)
YZH
185
540 mW
5.4 mW
297 mW
216 mW
(2)
YZH
75
1.3 W
13.3 mW
0.7 W
0.5 W
DEVICE
TPS657051/52
(1)
(2)
The JEDEC low-K (1s) board used to derive this data was a 3in × 3in, two-layer board with 2-ounce copper traces on top of the board.
The JEDEC high-K (2s2p) board used to derive this data was a 3in × 3in, multilayer board with 1-ounce internal power and ground.
7.7 Typical Characteristics
Table 1. Table Of Graphs
FIGURE
Efficiency DC-DC (VDCDC= 3.3 V), L = BRC1608 1.5 µH
vs Load current / PFM mode
Figure 1
Efficiency DC-DC (VDCDC= 3.3 V), L = BRC1608 1.5 µH
vs Load current / PWM mode
Figure 2
Efficiency DC-DC (VDCDC= 1.8 V), L = BRC1608 1.5 µH
vs Load current / PFM mode
Figure 3
Efficiency DC-DC (VDCDC= 1.8 V), L = BRC1608 1.5 µH
vs Load current / PWM mode
Figure 4
Line transient response DC-DC 1.8 V (PWM)
Scope plot
Figure 5
Line transient response DC-DC 1.8 V (PFM)
Scope plot
Figure 6
Line transient response LDO 2.8 V
Scope plot
Figure 7
Load transient response DC-DC 1.8 V (PWM/PFM)
20 mA to 180 mA
Scope plot
Figure 8
Load transient response DC-DC 1.8 V (PWM) 20 mA to 180 mA
Scope plot
Figure 9
Load transient response DC-DC 1.8 V (PFM/PWM)
20 mA to 360 mA
Scope plot
Figure 10
Load transient response DC-DC 1.8 V (PWM) 20 mA to 360 mA
Scope plot
Figure 11
Load transient response LDO 2.8 V
Scope plot
Figure 12
DC-DC PFM to PWM mode transition
Scope plot
Figure 13
DC-DC PWM to PFM mode transition
Scope plot
Figure 14
DC-DC Output voltage ripple in PFM mode
Scope plot
Figure 15
DC-DC Output voltage ripple in PWM mode
Scope plot
Figure 16
Startup timing DC-DC 1.8 V
Scope plot
Figure 22
Startup timing LDO 2.8 V
Scope plot
Figure 23
LDO PSRR
Scope plot
Figure 17
DC-DC Quiescent current
vs VINDCDC
Figure 18
LDO Quiescent current
vs VINDCDC
Figure 19
Shutdown current
vs VINDCDC
Figure 20
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
Submit Documentation Feedback
7
TPS657051, TPS657052
www.ti.com
100
100
90
90
80
80
70
70
Efficiency - %
Efficiency - %
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
60
3.5
3.6
3.8
4.0
4.2
4.5
4.8
5.0
5.5
6.0
50
40
30
20
10
VOUT = 3.3 V,
TA = 25°C
L = BRC1608 1.5μA
0
0.001
0.01
0.1
IO - Output Current - A
50
40
10
0
0.001
1
90
80
80
70
70
Efficiency - %
90
60
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
30
20
10
VOUT = 1.8 V,
TA = 25°C
L = BRC1608 1.5μA
0
0.001
0.01
0.1
IO - Output Current - A
0.01
0.1
IO - Output Current - A
VOUT = 1.8 V,
TA = 25°C
L = BRC1608 1.5 μA
60
50
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
40
30
20
10
0
0.001
1
Figure 3. Efficiency DC-DC (VDCDC=1.8 V) vs Load Current
PFM mode
1
Figure 2. Efficiency DC-DC (VDCDC=3.3 V) vs Load Current
PWM Mode
100
40
VOUT = 3.3 V,
TA = 25°C
L = BRC1608 1.5μA
20
100
50
3.5
3.6
3.8
4.0
4.2
4.5
4.8
5.0
5.2
5.5
6.0
30
Figure 1. Efficiency DC-DC (VDCDC=3.3 V) vs Load Current
PFM Mode
Efficiency - %
60
0.01
0.1
IO - Output Current - A
1
Figure 4. Efficiency DC-DC (VDCDC=1.8 V) vs Load Current
PWM mode
VINDCDC = 3.6V to 4.2V to 3.6V
Temperature = 25°C
VINDCDC
DCDC Load Current = 200mA
VDCDC = 1.8V
Mode = VINDCDC
VINDCDC = 3.6V to 4.2V to 3.6V
Temperature = 25°C
VINDCDC
VDCDC
VDCDC
DCDC Load Current = 75mA
VDCDC = 1.8V
Mode = GND
DCDC Load
DCDC Load
Time - 100 ms/div
Time - 100 ms/div
Figure 5. Line Transient Response DC-DC 1.8 V (PWM)
8
Submit Documentation Feedback
Figure 6. Line Transient Response DC-DC 1.8 V (PFM)
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
TPS657051, TPS657052
www.ti.com
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
VINDCDC = 5.0V
Temperature = 25°C
VINDCDC = 5.0V
VINLDO = 3.6V to 4.2V to 3.6V
Temperature = 25°C
DCDC Load Current = 20mA to 180mA
VDCDC = 1.8V
Mode = GND
VINLDO
LDO Load Current = 200mA
VLDO = 2.8V
VLDO
VDCDC
LDO Load
DCDC Load Current
Time - 100 ms/div
Time - 100 ms/div
Figure 7. Line Transient Response LDO 2.8 V
Figure 8. Load Transient Response DC-DC 1.8 V (PWM/PFM)
20 mA to 180 mA
VINDCDC = 5.0V
Temperature = 25°C
VINDCDC = 5.0V
Temperature = 25°C
DCDC Load Current = 20mA to 360mA
VDCDC = 1.8V
Mode = GND
VDCDC
DCDC Load Current = 20mA to 180mA
VDCDC = 1.8V
Mode = VINDCDC
VDCDC
DCDC Load Current
DCDC Load Current
Time - 100 ms/div
Time - 100 ms/div
Figure 9. Load Transient Response DC-DC 1.8 V (PWM)
20 mA to 180 mA
VINDCDC = 5.0V
Temperature = 25°C
Figure 10. Load Transient Response DC-DC 1.8 V
(PFM/PWM) 20 mA to 360 mA
VINDCDC = 5 V, VINLDO = 5 V
Temperature = 25°C
LDO Load Current = 20 mA to 180 mA
VLDO
VINDCDC = 5.0 V
VINLDO = 5.0 V
Temperature = 25°C
VDCDC
DCDC Load Current = 20mA to 360mA
VDCDC = 1.8V
Mode = VINDCDC
LDO Load Current = 20mA to 180mA
VLDO = 2.8V
VLDO = 2.8 V
LDO Load Current
DCDC Load Current
Time - 100 ms/div
Time - 100 ms/div
Figure 11. Load Transient Response DC-DC 1.8 V (PWM)
20 mA to 360 mA
Figure 12. Load Transient Response LDO
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
Submit Documentation Feedback
9
TPS657051, TPS657052
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
Mode
www.ti.com
VINDCDC = 5.0V
Temperature = 25°C
VDCDC
DCDC Load Current = 10mA
VDCDC = 1.8V
Mode = GND to VINDCDC
VINDCDC = 5.0V
Temperature = 25°C
Mode
VDCDC
SW
SW
DCDC Load Current = 10mA
VDCDC = 1.8V
Mode = VINDCDC to GND
DCDC Inductor Current
DCDC Inductor Current
Time - 10 ms/div
Time - 10 ms/div
Figure 13. DC-DC PFM to PWM Mode Transition
Figure 14. DC-DC PWM to PFM Mode Transition
VINDCDC = 5.0V
Temperature = 25°C
VINDCDC = 5.0V
Temperature = 25°C
DCDC Output
DCDC Load Current = 200mA
VDCDC = 1.8V
Mode = GND
DCDC Load Current = 60mA
VDCDC = 1.8V
Mode = GND
DCDC Output
SW
SW
DCDC Inductor Current
DCDC Inductor Current
Time - 2 ms/div
Time - 1 ms/div
Figure 15. DC-DC Output Voltage Ripple in PFM Mode
Figure 16. DC-DC Output Voltage Ripple in PWM Mode
60
100
Rejection Ratio - dB
80
50
Quiescent Current - μA
90
LDO VO = 2.8 V,
Load = 100 mA,
VI = 5 V PSRR
70
60
IO = 100 mA
50
40
30
20
Vout = 1.2V,
Mode = GND
ENDCDC1 = VINDCDC, no load
ENDCDC2 = GND
ENLDO = GND
25°C
85°C
-40°C
40
30
20
10
10
0
10
100
1k
10k
100k
f - Frequency - Hz
Figure 17. LDO PSRR
10
Submit Documentation Feedback
1M
10M
0
2.5
3
3.5
4
4.5
5
VCC - Supply Voltage - V
5.5
6
Figure 18. DC-DC Quiescent Current
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
TPS657051, TPS657052
www.ti.com
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
30
100
Quiescent Current - μA
80
70
Vout = 1.2V
Mode = GND
ENDCDC1 = GND
ENDCDC2 = GND
ENLDO =VINDCDC, no load
25
Shutdown Current - μA
90
60
50
85°C
25°C
40
30
20
Vout = 1.2V
Mode = GND
ENDCDC1 = GND
ENDCDC2 = GND
ENLDO = GND
20
85°C
25°C
-40°C
15
10
5
-40°C
10
0
2.92
3.42
3.92
4.42
4.92
5.42
VCC - Supply Voltage - V
Figure 19. LDO Quiescent Current
5.92
0
2.5
3
3.5
4
4.5
5
VCC - Supply Voltage - V
5.5
6
Figure 20. Shutdown Current
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
Submit Documentation Feedback
11
TPS657051, TPS657052
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
www.ti.com
8 Detailed Description
8.1 Overview
The TPS65705x integrates fixed-output voltage, two highly efficient step-down converters, along with an LDO.
Each regulator has dedicated input pins for easy control.
8.2 Functional Block Diagram
VCC
TPS657051/52
VIN1
2. 2 mH
L1
Vout1
MODE
DCDC1
EN1
400 mA
10 mF
FB 1
10 mF
PGND
CLK 0°
2 .25 MHz
Oscillator
CLK 180 °
L2
2. 2 mH
VIN2
EN2
Vout2
DCDC2
400 mA
FB 2
10 mF
PGND
VLDO
VINLDO
ENLDO
Vout3
2 .2 mF
LDO
200 mA
AGND
8.3 Feature Description
8.3.1 DC-DC Converter
The TPS65705x step-down converter operates with typically 2.25-MHz fixed-frequency pulse width modulation
(PWM) at moderate to heavy load currents. With MODE pin set to low, at light load currents the converter can
automatically enter Power Save Mode and operates then in PFM mode.
During PWM operation the converter use a unique fast response voltage mode control scheme with input voltage
feed-forward to achieve good line and load regulation allowing the use of small ceramic input and output
capacitors. At the beginning of each clock cycle initiated by the clock signal, the high-side MOSFET switch is
turned on. The current flows now from the input capacitor through the high-side MOSFET switch through the
inductor to the output capacitor and load. During this phase, the current ramps up until the PWM comparator trips
12
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
TPS657051, TPS657052
www.ti.com
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
Feature Description (continued)
and the control logic will turn off the switch. The current limit comparator will also turn off the switch in case the
current limit of the high-side MOSFET switch is exceeded. After an off time preventing shoot through current, the
low-side MOSFET rectifier is turned on and the inductor current will ramp down. The current flows now from the
inductor to the output capacitor and to the load. It returns back to the inductor through the low-side MOSFET
rectifier.
The next cycle will be initiated by the clock signal again turning off the low-side MOSFET rectifier and turning on
the on the high-side MOSFET switch. The DCDC1 converter output voltage is set to 3.3 V and the DCDC2
converter output voltage is set to 1.8 V per default. A 180° phase shift between DCDC1 and DCDC2 decreases
the input RMS current and synchronizes the operation of the two DC-DC converts. The FB pin must be directly
connected to the output voltage of DC-DC and no external resistor network must be connected.
8.3.2 Power Save Mode
The Power Save Mode is enabled with Mode Pin set to low. If the load current decreases, the converter will enter
Power Save Mode operation automatically. During Power Save Mode the converter skips switching and operates
with reduced frequency in PFM mode with a minimum quiescent current to maintain high efficiency. The
converter will position the output voltage typically +1% above the nominal output voltage. This voltage positioning
feature minimizes voltage drops caused by a sudden load step. The transition from PWM mode to PFM mode
occurs once the inductor current in the low-side MOSFET switch becomes zero, which indicates discontinuous
conduction mode. During the Power Save Mode the output voltage is monitored with a PFM comparator. As the
output voltage falls below the PFM comparator threshold of VOUT nominal +1%, the device starts a PFM current
pulse. The high-side MOSFET switch will turn on, and the inductor current ramps up. After the ON-time expires,
the switch is turned off and the low-side MOSFET switch is turned on until the inductor current becomes zero.
The converter effectively delivers a current to the output capacitor and the load. If the load is below the delivered
current, the output voltage will rise. If the output voltage is equal or higher than the PFM comparator threshold,
the device stops switching and enters a sleep mode with typical 25-µA current consumption.
If the output voltage is still below the PFM comparator threshold, a sequence of further PFM current pulses are
generated until the PFM comparator threshold is reached. The converter starts switching again once the output
voltage drops below the PFM comparator threshold. With a fast single threshold comparator, the output voltage
ripple during PFM mode operation can be kept small. The PFM Pulse is time controlled, which allows to modify
the charge transferred to the output capacitor by the value of the inductor. The resulting PFM output voltage
ripple and PFM frequency depend in first order on the size of the output capacitor and the inductor value.
Increasing output capacitor values and inductor values will minimize the output ripple. The PFM frequency
decreases with smaller inductor values and increases with larger values. The PFM mode is left and PWM mode
is entered in case the output current can not longer be supported in PFM mode. The Power Save Mode can be
disabled by setting Mode pin to high. The converter will then operate in fixed-frequency PWM mode.
8.3.2.1 Dynamic Voltage Positioning
This feature reduces the voltage under/overshoots at load steps from light to heavy load and vice versa. It is
active in Power Save Mode and regulates the output voltage 1% higher than the nominal value. This provides
more headroom for both the voltage drop at a load step, and the voltage increase at a load throw-off.
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
Submit Documentation Feedback
13
TPS657051, TPS657052
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
www.ti.com
Feature Description (continued)
8.3.2.2 Soft Start
The step-down converter in TPS657051/52 has an internal soft start circuit that controls the ramp up of the
output voltage. The output voltage ramps up from 5% to 95% of its nominal value within typical 250s. This limits
the inrush current in the converter during ramp up and prevents possible input voltage drops when a battery or
high impedance power source is used.
EN
95%
5%
VOUT
tStart
tRAMP
Figure 21. Soft Start
8.3.2.3 100% Duty Cycle Low Dropout Operation
The device starts to enter 100% duty cycle mode once the input voltage comes close to the nominal output
voltage. In order to maintain the output voltage, the high-side MOSFET switch is turned on 100% for one or more
cycles. With further decreasing VIN the high-side MOSFET switch is turned on completely. In this case the
converter offers a low input-to-output voltage difference. This is particularly useful in battery-powered applications
to achieve longest operation time by taking full advantage of the whole battery voltage range. The minimum input
voltage to maintain regulation depends on the load current and output voltage, and can be calculated as:
VINmin = VOmax + IOmax (RDS(on)max + RL)
where
•
•
•
•
IOmax = maximum output current plus inductor ripple current
RDS(on)max = maximum high-side switch RDSon
RL = DC resistance of the inductor
VOmax = nominal output voltage plus maximum output voltage tolerance
(1)
8.3.3 180° Out-of-Phase Operation
In PWM Mode the converters operate with a 180° turn-on phase shift of the PMOS (high-side) transistors. This
prevents the high-side switches of both converters from being turned on simultaneously, and therefore smooths
the input current. This feature reduces the surge current drawn from the supply.
8.3.3.1 Under-Voltage Lockout
The under voltage lockout circuit prevents the device from malfunctioning at low input voltages and from
excessive discharge of the battery and disables the converters and LDOs. The under-voltage lockout threshold is
typically 2.2 V.
8.3.4 Short-Circuit Protection
All outputs are short-circuit protected with a maximum output current as defined in the electrical specifications.
8.3.5 Thermal Shutdown
As soon as the junction temperature, TJ, exceeds typically 150°C for the DC-DC converter or LDO, the device
goes into thermal shutdown. In this mode, the low-side and high-side MOSFETs are turned-off. The device
continues its operation when the junction temperature falls below the thermal shutdown hysteresis again. A
thermal shutdown for the LDO or the DC-DC converter will disable both power supplies simultaneously.
14
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
TPS657051, TPS657052
www.ti.com
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
Feature Description (continued)
8.3.6 LDO
The low dropout voltage regulator is designed to operate well with low value ceramic input and output capacitors.
It operates with input voltages down to 1.7 V. The LDO offers a maximum dropout voltage of 200 mV at rated
output current. The LDO supports a current limit feature.
8.3.7 Enable for DCDC1, DCDC2 and LDO
Disabling the DC-DC converter or LDO, forces the device into shutdown, with a shutdown quiescent current as
defined in Electrical Characteristics. In this mode, the power FETs are turned-off and the entire internal control
circuitry is switched-off.
8.4 Device Functional Modes
DCDC1, DCDC2, and LDO have dedicated enable pins. If all enable pins are pulled low the device will remain
shutdown. If any of enable pins are pulled high corresponding regulators are enabled.
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
Submit Documentation Feedback
15
TPS657051, TPS657052
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The TPS65705x device is designed for use as a power supply for embedded camera modules or other portable
low-power equipment.
9.2 Typical Application
VCC
TPS 657051/52
2.2 μH
L1
VIN1
10 mF
MODE
DCDC1
EN1
400 mA
FB1
Vout1
10uF
PGND
CLK0°
2.25 MHz
Oscillator
VIN2
EN2
CLK180°
L2
2.2 μH
Vout2
DCDC2
400 mA
FB2
10 mF
PGND
VLDO
VINLDO
ENLDO
Vout3
2.2 mF
LDO
200 mA
AGND
9.2.1 Design Requirements
For this design example, use the parameters listed in Table 2 as the input parameters.
Table 2. Design Parameters
DESIGN PARAMETER
VALUE
Input Supply Voltage
3.3 V to 6 V
Switching Frequency
2.25 Mhz
9.2.2 Detailed Design Procedure
9.2.2.1 Output Filter Design (Inductor and Output Capacitor)
9.2.2.1.1 Inductor Selection
The converter operates typically with 2.2-µH output inductor. Larger or smaller inductor values can be used to
optimize the performance of the device for specific operation conditions. The selected inductor has to be rated for
its DC resistance and saturation current. The DC resistance of the inductor will influence directly the efficiency of
the converter. Therefore an inductor with lowest DC resistance should be selected for highest efficiency.
Equation 2 calculates the maximum inductor current under static load conditions. The saturation current of the
inductor should be rated higher than the maximum inductor current as calculated with Equation 2. This is
recommended because during heavy load transient the inductor current will rise above the calculated value.
16
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
TPS657051, TPS657052
www.ti.com
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
Vout
Vin
L ´ ¦
1ΔIL = Vout ´
ILmax =Ioutmax +
(2)
DIL
2
where
•
•
•
•
f = Switching Frequency (2.25 MHz typical)
L = Inductor Value
ΔIL = Peak-to-Peak inductor ripple current
ILmax = Maximum Inductor current
(3)
The highest inductor current will occur at maximum Vin.
Open core inductors have a soft saturation characteristic and they can usually handle higher inductor currents
versus a comparable shielded inductor.
A more conservative approach is to select the inductor current rating just for the maximum switch current of the
corresponding converter. It must be considered, that the core material from inductor to inductor differs and will
have an impact on the efficiency especially at high switching frequencies.
Notice that the step-down converter has internal loop compensation. As the internal loop compensation is
designed to work with a certain output filter corner frequency calculated as follows:
1
¦c =
with L = 2.2 m H, Cout = 10 m F
2 p L ´ Cout
(4)
This leads to the fact the selection of external L-C filter has to be coped with the above formula. As a general
rule of thumb the product of LxCout should be constant while selecting smaller inductor or increasing output
capacitor value.
Refer to Table 3 and the typical applications for possible inductors.
Table 3. Tested Inductors
INDUCTOR TYPE
INDUCTOR VALUE
SUPPLIER
BRC1608
1.5 µH
Taiyo Yuden
MLP2012
2.2 µH
TDK
MIPSA2520
2.2 µH
FDK
LPS3015
2.2 µH
Coilcraft
LQM21P
2.2 µH
Murata
9.2.2.1.2 Output Capacitor Selection
The advanced Fast Response voltage mode control scheme of the step-down converter allows the use of small
ceramic capacitors with a typical value of 10 µF, without having large output voltage under and overshoots during
heavy load transients. Ceramic capacitors having low ESR values result in lowest output voltage ripple and are
therefore recommended. For an inductor value of 2.2 µH, an output capacitor with 10 µF can be used. Refer to
Table 4.
If ceramic output capacitors are used, the capacitor RMS ripple current rating will always meet the application
requirements. Just for completeness the RMS ripple current is calculated as:
Vout
11
Vin ´
IRMSCout = Vout ´
L ´ ¦
2 ´ 3
(5)
At nominal load current the inductive converters operate in PWM mode and the overall output voltage ripple is
the sum of the voltage spike caused by the output capacitor ESR plus the voltage ripple caused by charging and
discharging the output capacitor:
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
Submit Documentation Feedback
17
TPS657051, TPS657052
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
www.ti.com
Vout
ö
1
Vin ´ æ
+ ESR ÷
ç
L ´ ¦
è 8 ´ Cout ´ ¦
ø
1DVout = Vout ´
(6)
Where the highest output voltage ripple occurs at the highest input voltage Vin.
At light load currents the converter operates in Power Save Mode and the output voltage ripple is dependent on
the output capacitor value. The output voltage ripple is set by the internal comparator delay and the external
capacitor. The typical output voltage ripple is less than 1% of the nominal output voltage
9.2.2.1.3 Input Capacitor Selection
Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is
required for best input voltage filtering and minimizing the interference with other circuits caused by high input
voltage spikes. The converters need a ceramic input capacitor of 10 µF. The input capacitor can be increased
without any limit for better input voltage filtering.
Table 4. Tested Capacitors
TYPE
COMPONENT SUPPLIER
VALUE
VOLTAGE
RATING
SIZE
MATERIAL
DC-DC Output Capacitor
Murata
GRM155R60G475ME47D
4.7 µF
4V
0402
Ceramic X5R
LDO I/O Capacitor
Murata
GRM155R60J225ME15D
2.2 µF
6.3 V
0402
Ceramic X5R
DC-DC Output Capacitor
Murata
GRM188R60J475K
4.7 µF
6.3 V
0603
Ceramic X5R
DC-DC I/O Capacitor
Murata
GRM188R60J106M69D
10 µF
6.3 V
0603
Ceramic X5R
9.2.3 Application Curves
VINDCDC = 5.0V
Temperature = 25°C
VDCDC = 1.8V
EN
EN
VDCDC
VINDCDC = 5.0V
VINLDO = 5.0V
Temperature = 25°C
VLDO
VLDO = 2.8V
SW
LDO Input Current
DCDC Input Current
Time - 80 ms/div
Time - 80 ms/div
Figure 22. Start-Up Timing DC-DC
Figure 23. Start-Up Timing LDO
10 Power Supply Recommendations
The device is optimized to be powered from single-cell Lithium battery. The input supply is required to stay above
UVLO threshold without shutting down DC-DC converters. Power input pins of each regulator should be properly
bypassed through ceramic capacitors that work best when placed close to the input pins as close as possible.
18
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
TPS657051, TPS657052
www.ti.com
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
11 Layout
11.1 Layout Guidelines
•
•
•
All input capacitors should be soldered as close as possible to the device.
All inductors should be placed as close as possible to switching pins through thick trace.
All feedback traces should be routed differentially and away from noisy traces such as switching signals.
11.2 Layout Example
VLDO
VINLDO
GND
GND
VIN1
VIN2
L1
L2
GND
Place input capacitors
close to VINx pins
Place inductors close
to Lx pins
GND
Run feedback traces
differentially
GND
FB1
FB2
VOUT1
VOUT2
Figure 24. Layout Recommendation
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
Submit Documentation Feedback
19
TPS657051, TPS657052
SLVSA08A – FEBRUARY 2010 – REVISED SEPTEMBER 2015
www.ti.com
12 Device and Documentation Support
12.1 Device Support
12.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
12.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 5. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
TPS657051
Click here
Click here
Click here
Click here
Click here
TPS657052
Click here
Click here
Click here
Click here
Click here
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
20
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: TPS657051 TPS657052
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TPS657051YZHT
ACTIVE
DSBGA
YZH
16
250
RoHS & Green
SNAGCU
Level-1-260C-UNLIM
-40 to 85
TPS657051
TPS657052YZHR
ACTIVE
DSBGA
YZH
16
3000
RoHS & Green
SNAGCU
Level-1-260C-UNLIM
-40 to 85
TPS657052
TPS657052YZHT
ACTIVE
DSBGA
YZH
16
250
RoHS & Green
SNAGCU
Level-1-260C-UNLIM
-40 to 85
TPS657052
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of