TPS659038EVM-090

User's Guide SWCU174A – July 2014 – Revised March 2017 TPS65903x-Q1 EVM User’s Guide This user’s guide describes the characteristics, operation, and use of the TPS65903x-Q1 EVM. An EVM description, GUI description, interface requirements, and complete schematic are included. 1 2 3 4 5 Contents Introduction ................................................................................................................... 1 1.1 EVM Overview ...................................................................................................... 2 1.2 EVM with Components Identified ................................................................................. 2 1.3 Power-Supply Requirements and Connections ................................................................. 3 1.4 Default Jumper Settings ........................................................................................... 4 EVM Schematics ............................................................................................................. 7 EVM BOM .................................................................................................................... 9 Powering up the Device ................................................................................................... 11 TPS65903x-Q1EVM Graphical User Interface (GUI) .................................................................. 12 5.1 GUI Tabs ........................................................................................................... 12 5.2 Running a Script with the GUI ................................................................................... 14 List of Figures ........................................................................................................................... 2 ................................................................................................................ 3 EVM Schematic .............................................................................................................. 7 EVM Schematic .............................................................................................................. 8 DUT_Control ................................................................................................................ 12 Registers .................................................................................................................... 13 Sample Script ............................................................................................................... 14 1 EVM 2 Power Supply 3 4 5 6 7 List of Tables 1 Default Jumper Settings for the TPS659038EVM ....................................................................... 4 2 EVM BOM .................................................................................................................... 9 Trademarks MSP430 is a trademark of Texas Instruments. Windows is a registered trademark of Microsoft Corporation. All other trademarks are the property of their respective owners. 1 Introduction The TPS659038-Q1 and TPS659039-Q1 devices are power-management integrated circuits (PMICs) for automotive applications. The device provides seven configurable step-down converters, with up to 9 A of output current for memory, processor core, input/output (I/O), or preregulation of LDOs. The TPS659038Q1 device contains 11 LDO regulators while the TPS659039-Q1 device contains 6 LDO regulators for external use. For more details, see the device data sheet, TPS65903x-Q1 Automotive Power Management Unit (PMU) for Processor. SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated TPS65903x-Q1 EVM User’s Guide 1 Introduction 1.1 www.ti.com EVM Overview The features of this EVM are as follows: • Allows monitoring of all LDO and SMPS output voltages. • Allows loading of all SMPS outputs. • Allows access to the GPIOs and other logic signals to test functionality. • Optimized layout for stable operation of all SMPS. • Onboard MSP430™ microcontroller to enable communication with the PMIC. • Graphical User Interface (GUI) on Windows® to allow access to the registers of the PMIC through USB-I2C. 1.2 EVM with Components Identified LDO Outputs (J46) USB GPIOs (J27) SMPS7 SMPS12/3 MSP430 SMPS45 SMPS3 LEDs: POWERGOOD VSYS (J20) RESET_OUT 3.135 V to 5.25 V LDORTC MSP430 GND SMPS6 SMPS9 SMPS8 VIO Selection (J31) Figure 1. EVM LEDs — Display status of POWERGOOD, RESET_OUT, LDORTC and power supply of MSP430 USB — Connection to PC to enable communication through the GUI MSP430 — Microcontroller used to convert USB data to I2C format SMPSxx — Monitor point for SMPS outputs J46 — Monitor point for LDO outputs J31 — Jumper used to select VIO voltage. J31 requires a jumper installed (only one), and by default is in position 10, 1V8. J27 — Jumper that provides access to the GPIOs J20 — VSYS power supply input. J20 is the same connector as SMPS123, and must not be confused to prevent applying VSYS to SMSP123-output. 2 TPS65903x-Q1 EVM User’s Guide SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated Introduction www.ti.com 1.3 Power-Supply Requirements and Connections Only one power supply is needed to power the VSYS domain of the PMIC. Apply 3.135 VDC to 5.25 VDC to the J20 connector of the TPS659038EVM to supply power to the PMIC device. Four-wire sensing of the input power supply is recommended and can be achieved through the middle two terminals of J20. Power for the MSP430 and the two fixed voltage LDOs (3.3-V and 1.8-V outputs) is supplied through the USB connection, as shown in Figure 2. Figure 2. Power Supply SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated TPS65903x-Q1 EVM User’s Guide 3 Introduction 1.4 www.ti.com Default Jumper Settings Table 1 lists the options for each header and the default jumper settings for the TPS659038EVM. Table 1. Default Jumper Settings for the TPS659038EVM Reference Jumper Setting Function Closed I2C1_SCL and I2C1_SDA are shorted Open I2C1_SCL and I2C1_SDA are separated Closed I2C2_SCL and I2C2_SDA are shorted Open I2C2_SCL and I2C2_SDA are separated Closed PWRDOWN pin is controlled by MSP430 Open PWRDOWN pin is floating Closed NRESWARM pin is controlled by MSP430 Open NRESWARM is floating Closed ENABLE1 pin is controlled by MSP430 Open ENABLE1 is floating Closed NSLEEP pin is controlled by MSP430 Open NSLEEP is floating Closed RESET_IN pin is controlled by MSP430 Open RESET_IN is floating Closed INT pin is connected to MSP430 Open INT pin is floating Closed SYNCDCDC pin is connected to GND Open SYNCDCDC pin is floating 1 GPADC_IN0 2 GPADC_IN1 3 GPADC_IN2 J3 J5 J7 J8 J9 J10 J11 J12 J13 J22 J23 J24 J25 J26 4 TPS65903x-Q1 EVM User’s Guide 4 GPADC_VREF Open POWERGOOD pin is floating Closed POWERGOOD pin is connected to GND Open CLK32KGO pin is floating Closed CLK32KGO pin is connected to GND Jumper b/w 1 and 2 BOOT0 is tied to LDORTC Jumper b/w 2 and 3 BOOT0 is tied to GND Jumper b/w 1 and 2 BOOT1 is tied to LDORTC Jumper b/w 2 and 3 BOOT1 is tied to GND Default Open Open Closed Closed Closed Closed Closed Open Open Open Open Open Jumper b/w 2 and 3 Jumper b/w 2 and 3 SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated Introduction www.ti.com Table 1. Default Jumper Settings for the TPS659038EVM (continued) Reference J27 J28 J29 J30 J31 Jumper Setting Function 1 GPIO_0 2 GPIO_1 3 GPIO_2 4 GPIO_3 5 GPIO_4 6 GPIO_5 7 GPIO_6 8 GPIO_7 9 REGEN1 10 RESET_OUT 11 LODRTC 12 GND 1 VSYS 2 PWRON 3 GND 1 VSYS 2 PWRON 3 GND - Reserved 1 VIO_IN 2 SMSP7 3 VIO_IN 4 SMSP9 5 VIO_IN 6 LDO5 7 VIO_IN 8 LDO3 9 VIO_IN 10 +1V8 11 VIO_IN Default Jumper b/w 8 and 11 to tie POWERHOLD pin to VRTC Open Open Closed Jumper b/w 9 and 10 12 +3V3 Open All LDO_INs are floating Closed All LDO_INs are connected to VSYS Open VPROG/TESTV is floating Closed VPROG/TESTV is connected to GND Open J36 — SMPS12/3 Open J37 — SMPS12/3 Open J38 — SMPS12/3 Open J39 — SMPS3 Open J40 — SMPS45 Open J41 — SMPS45 Open J42 — SMPS6 Open J43 — SMPS7 Open J44 — SMPS8 Open J45 — SMPS9 Open Open VCC1 isn't shorted to VSYS Closed VCC1 is shorted to VSYS J34 J35 J47 J48 Open POWERGOOD is floating Closed POWERGOOD is pulled up to 3.3V SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated Closed Closed Closed TPS65903x-Q1 EVM User’s Guide 5 Introduction www.ti.com Table 1. Default Jumper Settings for the TPS659038EVM (continued) Reference J46 6 TPS65903x-Q1 EVM User’s Guide Jumper Setting Function 1 LDO1 2 LDO1_SENSE 3 LDO1_GND_SENSE 4 LDO2 5 LDO2_SENSE 6 LDO2_GND_SENSE 7 LDO3 8 LDO3_SENSE 9 LDO3_GND_SENSE 10 LDO4 11 LDO4_SENSE 12 LDO4_GND_SENSE 13 LDO5 14 LDO5_SENSE 15 LDO5_GND_SENSE 16 LDO6 17 LDO6_SENSE 18 LDO6_GND_SENSE 19 LDO7 20 LDO7_SENSE 21 LDO7_GND_SENSE 22 LDO8 23 LDO8_SENSE 24 LDO8_GND_SENSE 25 LDO9 26 LDO9_SENSE 27 LDO9_GND_SENSE 28 LDOLN 29 LDOLN_SENSE 30 LDOLN_GND_SENSE 31 LDOUSB 32 LDOUSB_SENSE 33 LDOUSB_GND_SENSE 34 LDORTC 35 LDORTC 36 GND 37 LDOVANA 38 LDOVANA 39 GND 40 GND 41 GND 42 GND 43 GND 44 GND Default SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated EVM Schematics www.ti.com 2 EVM Schematics Figure 3. EVM Schematic SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback TPS65903x-Q1 EVM User’s Guide Copyright © 2014–2017, Texas Instruments Incorporated 7 EVM Schematics www.ti.com GND +3V3 VR3 J1 6 +5V 1 VCCA VCCB 16 2 1DIR ~1OE 15 3 2DIR ~2OE 14 SCLK 4 1A1 1B1 13 SIMO 5 1A2 1B2 12 CS 6 2A1 2B1 11 7 2A2 2B2 10 8 GND VIO_IN 9 1 J33 GND J32 33 GND 1 C49 4.7uF 2 3 IO9 4 IO8 GND 5 6 +3V3 7 D1 LED +3V3 10 IO10 11 C58 100nF 13 17 18 C56 100nF R73 1.5K 20 2 1 7 P4.1/PM_UCB1SIMO P8.1 P4.0/PM_UCB1STE/PM_U P8.2 P3.7/TB0OUTH/SVMOUT P3.6/TB0.6 DVSS1 P3.5/TB0.5 VCORE P3.4/UCA0RXD/UCA0SOM P1.5/TA0.4 P1.4/TA0.3 P1.3/TA0.2 P1.2/TA0.1 P1.1/TA0.0 P1.0/TA0CLK/ACLK GND R82 0 R83 0 R84 0 R85 0 R86 0 I2C1_SCL I2C1_SDA 9 I2C_SDA_MSP I2C2_SCL I2C2_SDA 61 62 P4.3/PM_UCB1CLK P4.2/PM_UCB1SOMI POWERGOOD 0 GND VSSU PU.0/DP 63 65 64 PUR PU.1/DM 67 66 VBUS VUSB 69 68 V18 AVSS2 70 72 73 74 71 P5.3/XT2OUT TEST/SBWTCK P5.2/XT2IN DVSS2 GND LDORTC GND PJ.0/TDO DVCC2 MSP430F552XIPN 1 Q3 PJ.1/TDI/TCLK 75 PJ.3/TCK P4.4/PM_UCA1TXD J48 Q1 GND 1 VCCA VCCB 16 2 1DIR ~1OE 15 3 2DIR ~2OE 14 SOMI 4 1A1 1B1 13 IO8 5 1A2 1B2 12 INT IO3 6 2A1 2B1 11 ENABLE1 IO7 7 2A2 2B2 10 8 GND 1 VIO_IN 60 59 58 57 56 55 GND1 9 VCCA VCCB 16 2 1DIR ~1OE 15 3 2DIR ~2OE 14 4 1A1 1B1 13 5 1A2 1B2 12 IO12 6 2A1 2B1 11 RESET_IN IO9 7 2A2 2B2 10 PWRDOWN 8 GND 54 53 GND SOMI 52 50 GND +3V3 SIMO VR5 51 R87 R88 VIO_IN C55 49 100nF 48 1.5K 47 1.5K GND 45 IO10 IO11 46 SCLK 44 GND1 NSLEEP NRESWARM 9 43 GND GND 42 41 C57 470nF R95 GND 10K 2 R72 1.5K P5.1/VREF-/VEREF- DVCC1 19 GND1 P3,3/UCA0TXD/UCA0SIM +3V3 D3 LED P4.6/PM_NONE P4.5/PM_UCA1RXD P3.2/UCB0CLK/UCA0STE +3V3 D2 LED P4.7/PM_NONE U2 P5.0/VREF+/VEREF+ P3.1/UCB0SOMI/UCB0SC +3V3 P5.6/TB0.0 P8.0 +3V3 GND P7.1/CB9/A13 P5.5/XOUT 16 GND P5.7/TB0.1 AVSS1 15 GND P7.0/CB8/A12 P5.4/XIN Q2 RESET_OUT P7.4/TB0.2 AVCC1 12 14 Q4 P7.5/TB0.3 P3.0/UCB0SIMO/UCB0SD R71 1.5K P7.6/TB0.4 P6.7/CB7/A7 P2.7/UCB0/STEUCA0CLK R74 1.5K 0 R81 VR4 P7.3/CB11/A15 9 IO11 0 R80 +3V3 P6.6/CB6/A6 P7.2/CB10/A14 8 D4 LED R79 GND GND P2.6/RTCCLK/DMAE0 +3V3 I2C_SCL_MSP R76 1.5K P6.5/CB5/A5 P2.5/TA2.2 4 P2.4/TA2.1 NC/FB P2.3/TA2.0 EN GND P7.7/TB0CLK/MCLK P2.2/TA2CLK/SMCLK 3 GND P6.4/CB4/A4 P2.1/TA1.2 GND 100 nF 76 5 P2.0/TA1.1 2 OUT P1.7/TA1.0 IN P1.6/TA1CLK/CBOUT 1 C48 100pF I2C_SDA_MSP GND GND +1V8 VR2 C52 22pF 8 100pF PJ.2/TMS GND GND +5V 5 C51 22pF Y2 I2C_SCL_MSP GND 24Mhz 77 C47 4.7uF 4 GND 78 NC/FB 80 EN 79 OUT GND 3 P6.1/CB1/A1 2 100 nF 4 C54 P6.2/CB2/A2 IN C46 C53 C50 1nF 5 P6.0/CB0/A0 +3V3 3 R77 11 R75 120K P6.3/CB3/A3 1 33 NMI/SBWTDIO/RST +5V VR1 1 2 3 4 5 6 7 8 9 10 10 GND +3V3 LDORTC BOOT0 BOOT1 GPIO_1 GPIO_2 GPIO_3 TESTV I2C2_SCL I2C2_SDA 2 R78 R89 R90 2.2K 2.2K VIO_IN I2C_SDA_MSP I2C_SCL_MSP Q6 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 Q5 IO12 IO7 CS J46 IO3 45 J6 J22 J17 J26 J28 1 2 3 4 SMPS123 SMPS1_2_FDBK SMPS12_GND_FB 1 2 3 4 1 2 3 4 GPADC_IN0 GPADC_IN1 GPADC_IN2 GPADC_VREF 1 2 3 SMPS7 SMPS7_FDBK GND R68 10k LDORTC BOOT1 1 2 3 R69 10k VSYS PWRON GND GND GND J14 J23 1 2 3 4 SMPS3 SMPS3_FDBK J27 1 2 POWERGOOD GND GND J24 J15 1 2 3 4 1 2 SMPS45 SMPS4_5_FDBK SMPS4_5_FDBK_GND CLK32KGAO GND J18 1 2 3 4 5 6 7 8 9 10 11 12 GPIO_0 GPIO_1 GPIO_2 GPIO_3 GPIO_4 GPIO_5 GPIO_6 GPIO_7 REGEN1 RESET_OUT LDORTC GND J29 1 2 3 4 1 2 3 SMPS8 SMPS8_FDBK R70 10k VSYS RPWRON GND GND J19 J30 1 2 3 4 SMPS9 SMPS9_FDBK 1 2 VIO_IN_TPS VIO_IN GND GND J16 J25 J20 1 2 3 4 SMPS6 SMPS6_FDBK 1 2 3 R67 10k LDORTC BOOT0 1 2 3 4 VSYS 46 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 LDO1 LDO1 LDO2 LDO2 LDO3 LDO3 LDO4 LDO4 LDO5 LDO5 LDO6 LDO6 LDO7 LDO7 LDO8 LDO8 LDO9 LDO9 LDOLN LDOLN +3V3 J31 1 2 3 4 5 6 7 8 9 10 11 12 VIO_IN SMPS7 VIO_IN SMPS9 VIO_IN LDO5 VIO_IN LDO3 VIO_IN +1V8 VIO_IN LDOUSB LDOUSB LDORTC LDORTC LDOVANA LDOVANA GND GND GND GND Figure 4. EVM Schematic 8 TPS65903x-Q1 EVM User’s Guide SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated EVM BOM www.ti.com 3 EVM BOM Table 2 is for TPS65903x-Q1 EVM. The latest BOM is included in the TPS65903x-Q1 data sheet. Table 2. EVM BOM Item Manufacturer Manufacturer Part No. Quantity Reference PCB Footprint Value 1 Murata GRM188R61A225KE34D 5 C1, C2, C3, C4, C5 cns_0603 2.2µF/0603/10V 2 Murata GRM155R61A104KA01D 1 C6 cns_0402 100nF/0402/10V 3 Murata GRM21BR61A106KE19L 1 C7 cns_0805 10µF/0805/10V 4 KEMET C0603C106M9PAC 1 C8 cns_0603 10µF/6.3V 5 Murata GRM155R60J104KA01D 4 C9, C17, C46, C48 cns_0402 100nF/0402/6.3V 6 Murata GRM21BR71A475KA73K 9 C10, C12, C14, C19, C23, C26, C27, C43, C45 cns_0805 4.7µF/0805/10V 7 Murata GRM32ER71A476ME15 9 C11, C13, C15, C20, C24, C25, C28, C42, C44 cns_1210_02 47µF/1210/10V 8 Murata GRM32ER71A476ME15 0 C16, C59 cns_1210_02 47µF/1210/10V - DNP cns_0402 2.2µF/0402/6.3V 9 Murata GRM155R60J225ME15D 14 C18, C29, C30, C31, C32, C33, C34, C35, C36, C37, C38, C39, C40, C41 10 Murata GRM155C1H120GA01D 2 C21, C22 cns_0402 12pF/0402/50V 11 Murata GRM155R60J475ME87 2 C47, C49 cns_0402 4.7µF/0402/6.3V 12 Murata GRM155R71H102KA01D 1 C50 0402 1nF/0402/50V 13 TDK C1005C0G1H220J 2 C51, C52 0402 22pF/0402/50V 14 Murata GRM1555C1H101JZ01D 2 C53, C54 0402 100pF/0402/50V 15 Murata GRM188R71C104KA01 3 C55, C56, C58 0603 100nF/0603/16V 16 AVX 04026D474KAT2A 1 C57 0402 470nF/0402/50V 0 C60, C61 0603 4.7nF/0603/16V - DNP 17 17 Osram LO T67K-L1M2 24 1 D1 PLCC-2 LO T67K-L1M2-24 18 Osram LY T67K-K2M1 26 3 D2, D3, D4 PLCC-2 LY T67K-K2M1 26 19 Hirose UX60-MB-5ST 1 J1 0.354 X 0.303 Inches UX60-MB-5ST 20 Digi-Key 277-6735-ND 2 J6, J20 5.08MM CONN HEADER 4POS 21 Digi-Key 277-1223-ND 6 J14, J15, J16, J17, J18, J19 3.81MM CONN HEADER VERT 4POS 22 Sullins PEC04SAAN 1 J22 2.54MM CONN HEADER .100 SINGL STR 4POS 23 Sullins PEC02SAAN 27 J3, J5, J7, J8, J9, J10, J11, J12, J13, J23, J24, J30, J33, J34, J35, J36, J37, J38, J39, J40, J41, J42, J43, J44, J45, J47, J48 2.54MM CONN HEADER .100 SINGL STR 2POS 24 Sullins PEC03SAAN 4 J25, J26, J28, J29 2.54MM CONN HEADER .100 SINGL STR 3POS 25 TE Connectivity 146130-5 2 J27, J31 2.54MM CONN HDR BRKWAY 12POS DUAL SMD 26 Sullins PEC36DBAN 1 J32 .500 x .378 inch Header, Right Angle 10 pins [72 pins strip] (DNP) 27 FCI 71918-144LF 1 J46 2.54MM CONN HEADER 44POS DUAL VERT PCB SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback TPS65903x-Q1 EVM User’s Guide Copyright © 2014–2017, Texas Instruments Incorporated 9 EVM BOM www.ti.com Table 2. EVM BOM (continued) Item 10 Manufacturer Manufacturer Part No. Quantity Reference PCB Footprint Value 28 Vishay IHLP1616ABER1R0M11 9 L2, L3, L4, L6, L7, L8, L9, L10, L11 29 Vishay IHLP1616ABER1R0M11 0 L5, L12 1µH/4.5A - DNP 30 TI TPS6591038_BGA 1 MX1 TPS659038 (customer supplied) 31 Fairchild BSS138 6 Q1, Q2, Q3, Q4, Q5, Q6 SOT23 BSS138 ERJ-2GE0R00X 28 R1, R3, R4, R5, R6, R7, R8, R21, R22, R23, R24, R25, R26, R28, R29, R30, R31, R32, R33, R34, R35, R44, R45, R46, R79, R81, R84, R86 r-s_0402 0_0402 (0 Ω) 1µH/4.5A 32 Panasonic 33 Panasonic ERJ-2GE0R00X 0 R80, R82, R83, R85 r-s_0402 0_0402 (0 Ω) - DNP 34 Panasonic ERJ-2RKF1002X 4 R67, R68, R69, R70 r-s_0402 10K_0402 (10 KΩ) ERA-2AEB152X 7 R71, R72, R73, R74, R76, R87, R88 r-s_0402 1.5k_0402 (1.5 KΩ) 120k_0402 (120 KΩ) 35 Panasonic 36 Panasonic ERJ-2RKF1203X 1 R75 r-s_0402 37 Yageo RC0402FR-0733RL 2 R77, R78 r-s_0402 33_0402 (33 Ω) 38 Yageo RC0402FR-072K2L 2 R89, R90 r-s_0402 2.2k_0402 (2.2 KΩ) 39 0 R91, R92, R93, R94 r-s_0402 0402 Resistor - DNP 41 0 R96, R97 r-s_0603 4.7_0603 (4.7 Ω) - DNP 42 0 RT1, RT2 0402 0402 RTC - DNP 1625854-3 (RCU-0C) 31 TP1, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP18, TP19, TP20, TP21, TP22, TP23, TP24, TP25, TP26, TP27, TP28, TP29, TP30, TP31, TP32, TP33 1.60mm x 0.8mm x 1.15mm 0603 Probe Pad 41 TE Connectivity 42 Keystone 5016 2 TP2, TP3 Test Point SMD 43 TI MSP430F5529IPN 1 U2 MSP430F55XIPN 44 TI TPS76333DBVT 1 VR1 DBV 45 TI TPS76318DBVT 1 VR2 DBV TPS76318DBVT 46 TI SN74AVC4T245PW 3 VR3, VR4, VR5 PW SN74AVC4T245PW 47 Epson FA-238 16.3840MB-C 1 Y1 48 Abracon ABLS-24.000MHZ-K4F-T 1 Y2 TPS65903x-Q1 EVM User’s Guide TPS76333DBVT 16.384MHz 3.7x12.7 mm 24MHz SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated Powering up the Device www.ti.com 4 Powering up the Device To 1. 2. 3. turn on the device, perform the following steps: Turn off the supply voltage, unplug the USB, and close the GUI. While the power supply is disabled, connect it to the EVM through the J20 connector. Plug the USB cable to the EVM and the computer. The MSP430 LED should blink a few times and then stay on. 4. Set the power supply to a voltage between 3.135 V and 5.25 V. Turn on the supply voltage. The LDORTC LED should light up. 5. Launch the GUI on the computer. All sequenced rails will power up to the predefined voltage. 6. Under the DUT_Control tab, send a logic high signal to the RESET_IN pin by checking the box next to RESET_IN and clicking Write Static. The RESET_OUT LED should light up, and the PMIC is now enabled. SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated TPS65903x-Q1 EVM User’s Guide 11 TPS65903x-Q1EVM Graphical User Interface (GUI) 5 www.ti.com TPS65903x-Q1EVM Graphical User Interface (GUI) The GUI for TPS659038EVM gives the user the ability to interact with the internal registers of the device while also allowing control of some input pins. The GUI can be downloaded here. The TPS659038EVM GUI installation requires the LabVIEW run-time engine, which can be downloaded from the National Instruments website. 5.1 GUI Tabs The TPS659038EVM GUI has two tabs. The first tab is labeled Registers, and the second tab is labeled DUT_Control. 5.1.1 DUT_Control The digital input signals to the PMIC are controlled through the DUT_Control tab of the GUI. There are six pins controlled by the GUI. To send a logic low to any of the pins, uncheck the corresponding box and click Write Static. To send a logic high to any of the pins, check the corresponding box and click Write Static. Figure 5. DUT_Control 12 TPS65903x-Q1 EVM User’s Guide SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated TPS65903x-Q1EVM Graphical User Interface (GUI) www.ti.com 5.1.2 Registers 2 I C communication with the device uses the Registers tab of the GUI. There are five groups of registers. Clicking the + symbol next to the group lists all the registers in that group. A second column next to the register name shows the address offset of that register. To read data from the register, select the appropriate register and click Read. The register data appears in the left column, and the hexadecimal value of the register appears in the Read Data field. To write data to the register, check the appropriate boxes in the right column and click Write, or enter the hex value in the Write Data field and click Write. The bits of the register are labeled on the left, with bit 0 in the top box and bit 7 in the bottom. Figure 6. Registers SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated TPS65903x-Q1 EVM User’s Guide 13 TPS65903x-Q1EVM Graphical User Interface (GUI) 5.2 www.ti.com Running a Script with the GUI The script editor is used to automate a series of register writes, static bit writes, and delays. To launch the script window from the main GUI menu, go to Tools → Show Script Window. The Script Editor opens with a blank window. To record a script, click Start/Rec, and run the commands from the main GUI. After each register write or static bit, the script editor records the command that was run. When finished, click Stop. To run the script again, click Run. To save the script that was created, click Save, and select the destination for the script file. Click Load to load a previously saved script. The two commands are: • tlv_write_reg_i2c1(REGISTER_NAME, VALUE), where the value is the decimal value to write. • wait(TIME_IN_MS) The script in Figure 7 turns on SMPS12 to 1.1 V, waits 2 ms, and then turns on SMPS3 to 1.35 V. These commands can be used to run a power up and power down sequence quickly, eliminating the need to manually turn on each rail. Figure 7. Sample Script 14 TPS65903x-Q1 EVM User’s Guide SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated Revision History www.ti.com Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Original (July 2014) to A Revision ........................................................................................................... Page • First public release of document ........................................................................................................ 1 SWCU174A – July 2014 – Revised March 2017 Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated Revision History 15 STANDARD TERMS FOR EVALUATION MODULES 1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms. 1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions set forth herein but rather shall be subject to the applicable terms that accompany such Software 1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned, or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production system. 2 Limited Warranty and Related Remedies/Disclaimers: 2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License Agreement. 2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused by neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specifications or instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality control techniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM. User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10) business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected. 2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day warranty period. 3 Regulatory Notices: 3.1 United States 3.1.1 Notice applicable to EVMs not FCC-Approved: FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and software developers to write software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter. 3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant: CAUTION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Interference Statement for Class A EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Interference Statement for Class B EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3.2 Canada 3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 or RSS-247 Concerning EVMs Including Radio Transmitters: This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Concernant les EVMs avec appareils radio: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Concerning EVMs Including Detachable Antennas: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Concernant les EVMs avec antennes détachables Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur 3.3 Japan 3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に 輸入される評価用キット、ボードについては、次のところをご覧ください。 http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified by TI as conforming to Technical Regulations of Radio Law of Japan. If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required to follow the instructions set forth by Radio Law of Japan, which includes, but is not limited to, the instructions below with respect to EVMs (which for the avoidance of doubt are stated strictly for convenience and should be verified by User): 1. 2. 3. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of Japan, Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to EVMs, or Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan. 【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの 措置を取っていただく必要がありますのでご注意ください。 1. 2. 3. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用 いただく。 実験局の免許を取得後ご使用いただく。 技術基準適合証明を取得後ご使用いただく。 なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。 上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ ンスツルメンツ株式会社 東京都新宿区西新宿６丁目２４番１号 西新宿三井ビル 3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/ /www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 3.4 European Union 3.4.1 For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive): This is a class A product intended for use in environments other than domestic environments that are connected to a low-voltage power-supply network that supplies buildings used for domestic purposes. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 4 EVM Use Restrictions and Warnings: 4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS. 4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information related to, for example, temperatures and voltages. 4.3 Safety-Related Warnings and Restrictions: 4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or property damage. If there are questions concerning performance ratings and specifications, User should contact a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit components may have elevated case temperatures. These components include but are not limited to linear regulators, switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the information in the associated documentation. When working with the EVM, please be aware that the EVM may become very warm. 4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the dangers and application risks associated with handling electrical mechanical components, systems, and subsystems. User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees, affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or designees. 4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal, state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local requirements. 5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as accurate, complete, reliable, current, or error-free. 6. Disclaimers: 6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY MATERIALS PROVIDED WITH THE EVM (INCLUDING, BUT NOT LIMITED TO, REFERENCE DESIGNS AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY EPIDEMIC FAILURE WARRANTY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS. 6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR IMPROVEMENT, REGARDLESS OF WHEN MADE, CONCEIVED OR ACQUIRED. 7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES, EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS. THIS OBLIGATION SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED. 8. Limitations on Damages and Liability: 8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE TERMS OR THE USE OF THE EVMS , REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI MORE THAN TWELVE (12) MONTHS AFTER THE EVENT THAT GAVE RISE TO THE CAUSE OF ACTION HAS OCCURRED. 8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY USE OF AN EVM PROVIDED HEREUNDER, INCLUDING FROM ANY WARRANTY, INDEMITY OR OTHER OBLIGATION ARISING OUT OF OR IN CONNECTION WITH THESE TERMS, , EXCEED THE TOTAL AMOUNT PAID TO TI BY USER FOR THE PARTICULAR EVM(S) AT ISSUE DURING THE PRIOR TWELVE (12) MONTHS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM SHALL NOT ENLARGE OR EXTEND THIS LIMIT. 9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s) will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s), excluding any postage or packaging costs. 10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas, without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas. Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2017, Texas Instruments Incorporated IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you (individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of this Notice. TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications (and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your noncompliance with the terms and provisions of this Notice. This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services. These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation modules, and samples (http://www.ti.com/sc/docs/sampterms.htm). Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2017, Texas Instruments Incorporated