www.ti.com
Table of Contents
User’s Guide
Using the TPS8802EVM
ABSTRACT
This quick-start guide describes the operation and use of the TPS8802 evaluation module (EVM) and the
accompaning EVM graphical user interface control software.
Table of Contents
1 Introduction.............................................................................................................................................................................3
1.1 Applications........................................................................................................................................................................3
1.2 Features............................................................................................................................................................................. 3
1.3 Recommended Equipment.................................................................................................................................................3
2 Setup........................................................................................................................................................................................4
2.1 Sensor Connections...........................................................................................................................................................4
2.2 Jumper and Switch Configurations.................................................................................................................................... 4
2.3 Power Connection..............................................................................................................................................................5
2.4 USB2ANY Connection....................................................................................................................................................... 6
3 Analog Evaluation...................................................................................................................................................................8
3.1 CO AFE Evaluation............................................................................................................................................................ 9
3.2 Photo AFE Evaluation...................................................................................................................................................... 13
3.3 Power Management and Sleep Mode..............................................................................................................................19
3.4 Horn Driver Evaluation..................................................................................................................................................... 21
3.5 Register Map....................................................................................................................................................................28
4 Board Layout.........................................................................................................................................................................29
5 Schematic and Bill of Materials...........................................................................................................................................33
5.1 Schematic........................................................................................................................................................................ 33
5.2 Bill of Materials.................................................................................................................................................................34
6 Revision History................................................................................................................................................................... 36
List of Figures
Figure 2-1. Switch, Jumper, and Power Connections..................................................................................................................5
Figure 2-2. TPS880x GUI Connected to USB2ANY Adapter...................................................................................................... 6
Figure 2-3. Test Command Successful........................................................................................................................................7
Figure 3-1. Evaluation Selection Menu........................................................................................................................................8
Figure 3-2. CO Amplifier Settings................................................................................................................................................ 9
Figure 3-3. Clean Air CO Amplifier Output................................................................................................................................ 10
Figure 3-4. CO Amplifier Output with Sensor and Calibration Gas............................................................................................10
Figure 3-5. COTEST_EN Register Bit........................................................................................................................................11
Figure 3-6. CO Connectivity Test without Sensor...................................................................................................................... 12
Figure 3-7. CO Connectivity Test with Sensor........................................................................................................................... 12
Figure 3-8. Photo Amplifier Settings.......................................................................................................................................... 13
Figure 3-9. LED Power Supply Settings.................................................................................................................................... 14
Figure 3-10. LED Driver Settings...............................................................................................................................................15
Figure 3-11. EVM Photo Measurement Probe Configuration.....................................................................................................16
Figure 3-12. LED A Signals....................................................................................................................................................... 17
Figure 3-13. LED B Signals....................................................................................................................................................... 17
Figure 3-14. Photo Signal with Photo Chamber........................................................................................................................ 18
Figure 3-15. Power Management Evaluation............................................................................................................................ 19
Figure 3-16. Power Management Measurement....................................................................................................................... 19
Figure 3-17. Sleep Mode with SLP_BST = 1............................................................................................................................. 20
Figure 3-18. TPS8802EVM and Three-terminal Piezo Setup....................................................................................................21
Figure 3-19. Register Map: CONFIG2 Register.........................................................................................................................22
Figure 3-20. Register Map: ENABLE2 Register........................................................................................................................ 22
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
1
Trademarks
www.ti.com
Figure 3-21. Register Map: BOOST Register............................................................................................................................ 23
Figure 3-22. EVM Three-terminal Horn Driver Measurement Probe Configuration...................................................................23
Figure 3-23. Untuned HORNSL, HORNBR, and HORNFB Waveforms.................................................................................... 24
Figure 3-24. Feedback Potentiometer....................................................................................................................................... 24
Figure 3-25. Tuned HORNSL, HORNBR, and HORNFB Waveforms........................................................................................25
Figure 3-26. TPS8802EVM and Two-terminal Piezo Setup.......................................................................................................26
Figure 3-27. Two-terminal Piezo Waveforms (HORNFB to ground).......................................................................................... 27
Figure 3-28. Two-terminal Piezo Waveforms (HORNFB to MCU)............................................................................................. 27
Figure 3-29. Register Map Search Function..............................................................................................................................28
Figure 4-1. TPS8802EVM Top Layer PCB Layout.....................................................................................................................29
Figure 4-2. TPS8802EVM Ground Layer PCB Layout.............................................................................................................. 30
Figure 4-3. TPS8802EVM Power Layer PCB Layout................................................................................................................ 31
Figure 4-4. TPS8802EVM Bottom Layer PCB Layout............................................................................................................... 32
Figure 5-1. TPS8802EVM Schematic........................................................................................................................................33
List of Tables
Table 2-1. VMCU and VBST Power-up Voltage...........................................................................................................................4
Table 5-1. Bill of Materials..........................................................................................................................................................34
Trademarks
USB2ANY™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
2
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Introduction
1 Introduction
The TPS8802EVM is used to evaluate the TPS8802 smoke and CO alarm analog front end (AFE) and power
management IC. The EVM allows for easy connection from the TPS8802 to a user-supplied photoelectric
chamber and carbon monoxide sensor. The TPS8802 GUI interfaces with the EVM to quickly evaluate the
photo amplifier, LED driver, and CO amplifier performance, system power consumption, and other blocks
with the register map. For a more thorough evaluation, an external microcontroller can be connected to the
TPS8802EVM to create a smoke detection system.
1.1 Applications
•
•
10-year battery smoke and CO alarms
AC powered smoke and CO alarms
1.2 Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Dual LED drivers for blue and IR LEDs
Wide bandwidth, low offset photodiode amplifier
Ultra-low power CO transimpedance amplifier
LDOs for internal analog blocks and external microcontroller
Single buffered analog output AMUX for CO and photo signals
Serial interface for configuring amplifiers, drivers, regulators
Default-enabled boost converter for 2-V battery operation
Horn driver with self-resonant and PWM modes
Interconnect driver for multi-alarm connection
Power-saving sleep mode with wake-up interrupt
Battery test load
Under-voltage, over-temperature fault monitors
Wide input voltage range for flexible power supply configuration
1.3 Recommended Equipment
•
•
•
•
•
2-V to 15.5-V power supply capable of 100 mA
USB2ANY™ interface adaptor
TPS880x GUI software
– Installation files are available in the TPS8802EVM product folder
Multimeter for measuring supply current, regulator voltages and CO amplifier output
Oscilloscope for measuring photodiode signal pulse shape
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
3
Setup
www.ti.com
2 Setup
Specific connections on the TPS8802EVM board require configuration before starting the evaluation.
2.1 Sensor Connections
TI recommends connecting a photoelectric smoke chamber and CO sensor to the TPS8802EVM for the
evaluation. The TPS8802EVM has a built-in photodiode (D7), blue LED (D8), and IR LED (D6) for functional
testing. These components can be de-soldered in order to connect a photoelectric chamber photodiode, IR LED,
and/or blue LED its place. Ensure the photodiode wires are kept short to preserve signal integrity.
The CO sensor is connected to J17 screw terminals with the sensor counter terminal tied to AGND.
2.2 Jumper and Switch Configurations
The S1 switch position determines the VMCU and VBST voltage at power-up. Ensure that only one S1 subswitch is in the ON position. Table 2-1 displays the VMCU and VBST voltage corresponding with each S1 switch
position. For proper operation with the USB2ANY adapter, set VMCU to 3.3 V with sub-switch 4.
Table 2-1. VMCU and VBST Power-up Voltage
S1 Switch Position
VMCU (V)
VBST (V)
1
1.5
3
2
1.8
3
3
2.5
4
4
3.3
5
The J2 jumper connects VBST to VCC. With the J2 jumper connected and the power supply connected to VBAT,
the boost converter supplies power via VCC. This configuration allows the EVM to operate at a voltage level
from 2 V to 11.5 V1.
The J6 jumper selects the I2C device address. Connect J6 to the AGND position to set the address to 0x3F.
Connect J6 to the VMCU position to set the address to 0x2A. The GUI is compatible with both options and
defaults to 0x2A.
1
4
The J14 shunt connecting VBAT to DINB limits the VBAT voltage to 11.5 V. If the shunt is moved to J1 connecting LEDLDO to DINB,
up to 15.5 V can be supplied on VBAT.
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Setup
Figure 2-1. Switch, Jumper, and Power Connections
2.3 Power Connection
Connect the power supply to VBAT and PGND. Set the power supply to 2 V, 100 mA2. Enable the power supply
and measure the voltage on VMCU (TP27) to ensure it is operating at the voltage option selected by S1:
•
•
•
•
1.5 V
1.8 V
2.5 V
3.3 V
Measure the voltage on VBST to ensure it is either 3 V, 4 V, or 5 V. See Table 2-1 for more information on the
initial VMCU and VBST voltage.
2
Peak current drawn from the supply is 600 mA for boost converter operation. If device does not power up with 100 mA current limit,
increase the power supply current limit to 600 mA.
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
5
Setup
www.ti.com
2.4 USB2ANY Connection
Use a USB cable to connect the USB2ANY adapter to a computer with the TPS880x GUI installed. Open
the TPS880x GUI and verify the USB2ANY adapter is recognized (see Figure 2-2). With the EVM powered,
connect the USB2ANY adapter to the EVM using the USB2ANY adapter 10-pin ribbon cable. Click EXPLORE
TPS8802EVM then QUICK START and select the device address corresponding to the J6 jumper (see Section
2.2). Send the test command to verify the EVM, USB2ANY adapter, and GUI software are all connected.
Figure 2-2. TPS880x GUI Connected to USB2ANY Adapter
6
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Setup
Figure 2-3. Test Command Successful
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
7
Analog Evaluation
www.ti.com
3 Analog Evaluation
Click START EVALUATION and select the feature to evaluate. The Analog Front End section guides the CO
AFE and photo AFE evaluation, and the Power Saving Mode section guides the standby power consumption
and sleep mode evaluation. Enter the register map to evaluate the other blocks in the TPS8802 device.
Figure 3-1. Evaluation Selection Menu
8
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Analog Evaluation
3.1 CO AFE Evaluation
If a CO sensor is available, connect it to the J17 terminal block. Select the feedback resistance and reference
voltage in the GUI software. The TPS8802EVM default configuration uses the internal resistors and references.
To use an external feedback resistor, solder a resistor to R5. To use an external input resistor, replace the
R1 0-Ω resistor with the required input resistance. The output resistor filters the CO amplifier output when a
capacitor is installed on C3.
Set the AMUX SELECTION to CO AMPLIFIER. Enable the CO amplifier and measure the voltage on
AMUX_BUF.
Figure 3-2. CO Amplifier Settings
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
9
Analog Evaluation
www.ti.com
Figure 3-3. Clean Air CO Amplifier Output
Figure 3-4. CO Amplifier Output with Sensor and Calibration Gas
10
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Analog Evaluation
3.1.1 CO Connectivity Test
A simple test confirms that the CO sensor is connected to the EVM. Remove the shunt connected to J7 and
connect a shunt to J15 and J16. Write COTEST_EN = 1 and measure the pulse shape on AMUX_BUF using
an oscilloscope. When COTEST_EN = 1, the PREF pin is pulled low and injects charge into the CO sensor and
amplifier. The AMUX pulse shape is different if the CO sensor is disconnected. Write COTEST_EN = 0, remove
the J15 and J16 shunts, and connect the J7 shunt when finished.
Figure 3-5. COTEST_EN Register Bit
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
11
Analog Evaluation
www.ti.com
Figure 3-6. CO Connectivity Test without Sensor
Figure 3-7. CO Connectivity Test with Sensor
12
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Analog Evaluation
3.2 Photo AFE Evaluation
Connect the photoelectric chamber to the EVM. If a photoelectric chamber is not available, place a box over the
EVM to block ambient light and reflect the EVM LED light into the photodiode when testing the photo AFE.
Enable the photo amplifier, photo gain amplifier, and set the AMUX SELECTION to PHOTO GAIN AMPLIFIER.
Select the photo reference on the EVM with jumper J7 and enable the photo reference voltage if the reference is
set to PREF. Set the gain factor to the required value. If no extra gain is required, set the AMUX SELECTION to
PHOTO AMPLIFIER.
It is recommended to install a 470 kΩ resistor connecting PREF to VINT if the photo gain is set to 11x, 20x, or
35x. The 470 kΩ resistor changes the PREF voltage to 70mV and prevents the gain stage output from dropping
below 50 mV in worst-case conditions.
Figure 3-8. Photo Amplifier Settings
Configure the power to the LEDs. By default, LED A is connected to LEDLDO and LED B is connected to VBAT.
Use the J1, J5, J8, and J14 jumpers to select which supply powers each LED. Enable the LEDLDO if it powers
either LED.
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
13
Analog Evaluation
www.ti.com
Figure 3-9. LED Power Supply Settings
Configure the PWM pulse settings for the LED driver. The default setting 201 ms pulse rate and 1 ms pulse width
sufficiently tests the LED driver. This setting controls the PWM signal from the USB2ANY adapter to the EVM.
Configure the LED current for each driver. The default EVM CSA resistance is 10 Ω and the default EVM CSB
resistance is 1.3 Ω. These resistors can be switched on the EVM to change the LED current and temperature
compensation. Set the DAC voltage to fine tune the LED current. Set the temperature coefficient to the required
setting. Click SETUP TEST after configuring the photo amplifier, LED power supply, and LED driver.
14
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Analog Evaluation
Figure 3-10. LED Driver Settings
Select the LED to be tested. Enable the LED PWM to send the PWM signal to the LEDEN pin. Enable
LEDPIN_EN to control the LED driver using the LEDEN pin. Place a box over the EVM if the EVM LEDs and
photodiode are used to block ambient light and reflect the LED light into the photodiode.
Use an oscilloscope to measure the LED current, photo input amplifier, and photo gain amplifier signals. Probe
LEDEN to measure the LED control signal. Probe CSA or CSB to measure the LED driver current. Probe PDO to
measure the photo input stage amplifier. Probe AMUX_BUF to measure the photo gain stage amplifier.
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
15
Analog Evaluation
www.ti.com
Figure 3-11. EVM Photo Measurement Probe Configuration
16
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Analog Evaluation
Figure 3-12. LED A Signals
Figure 3-13. LED B Signals
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
17
Analog Evaluation
www.ti.com
Figure 3-14. Photo Signal with Photo Chamber
18
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Analog Evaluation
3.3 Power Management and Sleep Mode
3.3.1 Power Management
The power management evaluation page allows the user to conveniently control many blocks that are critical for
system power consumption. Use the interface to enable and disable each block. Connect a multimeter in series
with the power supply to measure current. Remove the J4 USB2ANY adapter cable when performing critical
measurements. Raise the VBAT voltage above VINT and VMCU if the boost converter is disabled. In Figure
3-16, the VBAT voltage is raised to 3.6 V to maintain regulation of the MCULDO.
Figure 3-15. Power Management Evaluation
Figure 3-16. Power Management Measurement
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
19
Analog Evaluation
www.ti.com
3.3.2 Sleep Mode
Sleep mode disables blocks for a programmable amount of time and flags the MCU when sleep mode is exited.
Enter the required amount of sleep time via the GUI and click ENTER to start the sleep timer. Click EXIT to exit
sleep mode if the device is in sleep mode. Probe the GPIO pin to measure the interrupt signal that occurs when
the sleep timer finishes.
CLEAR INTERRUPT resets the interrupt signal. The interrupt signal is reset whenever the STATUS1 register
is read. By default, the GUI reads all registers every 5 seconds. Disable the automatic register reading by
navigating to the Register Map page and changing the Auto Read setting to Off.
Figure 3-17. Sleep Mode with SLP_BST = 1
20
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Analog Evaluation
3.4 Horn Driver Evaluation
The TPS8802EVM supports direct connection with a piezo horn. The HBEN pin and HORN_EN register bit
enables the integrated horn driver and operates independent of any smoke or CO condition. Connect the piezo
horn terminal to the respective EVM terminal as shown in Figure 3-18. The silver (HORNSL, M) and brass
(HORNBR, G) connect to the J13 terminal block. For a three-terminal piezo horn, connect the piezo feedback
terminal to PIEZOF in the J10 terminal block. Additionally, populate jumpers at J11 and J12 for a three-terminal
piezo configuration.
3.4.1 Three-Terminal Piezo Evaluation
Figure 3-18. TPS8802EVM and Three-terminal Piezo Setup
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
21
Analog Evaluation
www.ti.com
In the TPS880x GUI navigate to the register map. The horn driver evaluation modifies the following registers:
configuration register, enable register, and the boost converter register. The configuration register determines
how the horn driver is configured.
Figure 3-19. Register Map: CONFIG2 Register
•
•
•
For two-terminal mode: HORNSEL = 0.
For three-terminal mode: HORNSEL = 1.
HORN_THR (relevant to three-terminal mode), see Section 3.4.2.
The enable register controls the horn driver circuit.
Figure 3-20. Register Map: ENABLE2 Register
•
22
Set HORN_EN = 1.
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Analog Evaluation
Since the boost converter supplies the horn driver supply voltage, adjusting the booster converter registers
affects the horn loudness.
Figure 3-21. Register Map: BOOST Register
•
•
Set BST_CLIM = 30 mA to 500 mA.
Set VBST = 2.7 V to 15 V.
Use an oscilloscope to probe the EVM test points: HORNSL (TP16), HORNBR (TP16), and HORNFB (TP35).
Figure 3-22. EVM Three-terminal Horn Driver Measurement Probe Configuration
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
23
Analog Evaluation
www.ti.com
3.4.2 Three-Terminal Piezo Tuning
Set the HBEN pin (TP31) high by connecting it to the VMCU voltage. An untuned piezo feedback network
exhibits the following waveform.
Figure 3-23. Untuned HORNSL, HORNBR, and HORNFB Waveforms
From the figure above, HORNSL, HORNBR, and HORNFB operate below the expected piezo rated frequency
of 3.5 kHz. To tune the piezo, enable the horn driver circuit and adjust the potentiometer, see Figure 3-24. A
current ammeter in series with the VBAT power supply will also assist with piezo tuning, tune the potentiometer
to achieve the peak current draw for the system and the resonant oscillation observed in Figure 3-25.
Figure 3-24. Feedback Potentiometer
24
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Analog Evaluation
Achieving resonance on the horn pins, the duty cycle can be further fine-tuned in the register map under the
configuration registers: CONFIG2 register with the HORN_THR registers. To achieve maximum loudness, adjust
the “HORN_THR” value that operates the horn driver circuit at approximately 50% duty cycle. A tuned piezo will
generate the following waveforms.
Figure 3-25. Tuned HORNSL, HORNBR, and HORNFB Waveforms
HORNSL and HORNBR are square waves out of phase by 180° with each other. Both waveforms operate near
a 50% duty cycle. Additionally, HORNSL, HORNBR, and HORNFB oscillate at the piezo resonance frequency of
3.5 kHz.
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
25
Analog Evaluation
www.ti.com
3.4.3 Two-Terminal Piezo Evaluation
Connect a function generator or a microcontroller digital output pin to the HBEN test point: TP31 and connect
HORNFB to ground. For an alternative configuration, feed the HORNFB pin with an inverse polarity waveform
of HBEN square wave. To improve rise time and fall time of the output and reduces power dissipation, place a
1-mH inductor between the external piezo M wire and EVM HORNSL terminal. Additionally, remove jumper J11
and jumper J12 with PIEZOF terminal floating.
Figure 3-26. TPS8802EVM and Two-terminal Piezo Setup
In Figure 3-27, set a square wave with the piezo oscillation frequency on the HBEN test point and ground the
HORNFB test point. Probe both the HORNBR test point and HORNSL test point to measure the piezo voltage
waveforms.
26
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Analog Evaluation
Figure 3-27. Two-terminal Piezo Waveforms (HORNFB to ground)
For Figure 3-28, set square waveforms is on both the HBEN test point and the HORNFB test point (equal but
opposite polarity). Likewise, probe the piezo test points to observe the piezo voltage waveforms.
Figure 3-28. Two-terminal Piezo Waveforms (HORNFB to MCU)
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
27
Analog Evaluation
www.ti.com
3.5 Register Map
Use the register map to evaluate other blocks in the TPS8802. Use the search to find register bits that
correspond to a certain block or function. Load and save register map configurations in the File menu. Click
the question mark icon (?) to display more information about the selected register or bits.
Figure 3-29. Register Map Search Function
28
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Board Layout
4 Board Layout
Figure 4-1. TPS8802EVM Top Layer PCB Layout
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
29
Board Layout
www.ti.com
Figure 4-2. TPS8802EVM Ground Layer PCB Layout
30
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Board Layout
Figure 4-3. TPS8802EVM Power Layer PCB Layout
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
31
Board Layout
www.ti.com
Figure 4-4. TPS8802EVM Bottom Layer PCB Layout
32
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Schematic and Bill of Materials
5 Schematic and Bill of Materials
5.1 Schematic
A.
It is recommended to install a 470 kΩ resistor connecting PREF to VINT if the photo gain is set to 11x, 20x, or 35x. The 470 kΩ resistor
changes the PREF voltage to 70 mV and prevents the gain stage output from dropping below 50 mV in worst-case conditions.
Figure 5-1. TPS8802EVM Schematic
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
33
Schematic and Bill of Materials
www.ti.com
5.2 Bill of Materials
Table 5-1. Bill of Materials
REF DES
QTY
VALUE
DESCRIPTION
SIZE
Printed Circuit Board
PART NUMBER
PCB1
1
TPS880x
C2, C7, C12
3
0.1 µF
Capacitor, ceramic, 0.1 µF, 25 V, ±5%, X7R, 0603
0603
06033C104JAT2A
C4, C13, C16,
C18
4
1 µF
Capacitor, ceramic, 1 µF, 16 V, ±10%, X5R, 0603
0603
C0603C105K4PACT
U
C5
1
1 µF
Capacitor, ceramic, 1 µF, 16 V, ±10%, X7R, 0603
0603
EMK107B7105KA-T
C6, C11
2
4.7 µF
Capacitor, ceramic, 4.7 µF, 25 V, ±10%, X7R, 0805
0805
C2012X7R1E475K12
5AB
C8, C9, C14,
C15
4
47 µF
Capacitor, ceramic, 47 µF, 16 V, ±20%, X6S, 1210
1210
GRM32EC81C476ME
15L
C17, C21, C22
3
1000 pF
Capacitor, ceramic, 1000 pF, 50 V, ±10%, X7R, 0603
0603
C0603X102K5RACT
U
C20
1
330 pF
Capacitor, ceramic, 330 pF, 50 V, ±10%, X7R, 0603
0603
C0603C331K5RACT
U
C23
1
100 pF
Capacitor, ceramic, 100 pF, 50 V, ±5%, C0G/NP0, 0603
0603
885012006057
C24, C25
2
10 pF
Capacitor, ceramic, 10 pF, 50 V, ±5%, C0G/NP0, 0603
0603
06035A100JAT2A
D1, D2, D3
3
100 V
Diode, Switching, 100 V, 0.15 A, SOD-123
SOD-123
1N4148W-TP
D5
1
20 V
Diode, Schottky, 20 V, 0.5 A, SOD-123
SOD-123
MBR0520LT1G
D6
1
Infrared
LED, Infrared, TH
D5.5 mm
SFH 4556
D7
1
D5.7×H9 mm
SFH 213
D8
1
H1, H2, H3, H4
4
Machine Screw, Round, #4-40 × 1/4, Nylon, Philips
panhead
H5, H6, H7, H8
4
Standoff, Hex, 0.5"L #4-40 Nylon
J1, J5, J6, J7,
J8, J14
6
Header, 2.54 mm, 3×1, Tin, TH
Header, 2.54
mm, 3×1, TH
22284033
J2, J9, J11, J12,
J15, J16
6
Header, 2.54 mm, 2×1, Tin, TH
Header, 2.54
mm, 2×1, TH
22284023
J3, J10, J13,
J17
4
Terminal Block, 5.08 mm, 2×1, TH
Terminal Block, 039544-3002
5.08 mm, 2×1,
TH
J4
1
Header (shrouded), 100mil, 5×2, Gold, TH
5×2 Shrouded
header
L1
1
LBL1
1
R1
1
0
R2
1
R3
1
R4
R6
Silicon PIN Photodiode, TH
Blue
33 µH
LED, Blue, TH
D3.1 mm
Screw
Standoff
Inductor, Drum Core, Ferrite, 33 uH, 0.7 A, 0.38 ohm,
SMD
5×3×4.8 mm
Thermal Transfer Printable Labels, 0.650" W × 0.200" H 10,000 per roll
PCB Label
0.650 × 0.200
inch
LTL1CHTBK4
NY PMS 440 0025
PH
1902C
5103308-1
SDR0503-330KL
THT-14-423-10
Resistor, 0, 5%, 0.063 W, 0402
0402
RC0402JR-070RL
10.0 kΩ
Resistor, 10.0 k, .1%, .0625 W, 0402
0402
RT0402BRD0710KL
100 kΩ
Resistor, 100 k, 0.1%, 0.1 W, 0603
0603
RG1608P-104-B-T5
1
10.0 Ω
Resistor, 10.0, 0.5%, 0.1 W, 0603
0603
RT0603DRE0710RL
1
1.30 Ω
Resistor, 1.30, 0.5%, 0.1 W, 0603
0603
RT0603DRE071R3L
R7, R8
2
33 kΩ
Resistor, 33 k, 5%, 0.1 W, AEC-Q200 Grade 0, 0603
0603
CRCW060333K0JNE
A
R9, R10
2
1.0 kΩ
Resistor, 1.0 k, 5%, 0.063 W, AEC-Q200 Grade 0, 0402
0402
CRCW04021K00JNE
D
R11
1
2.4 MΩ
Resistor, 2.4 M, 5%, 0.1 W, AEC-Q200 Grade 0, 0603
0603
CRCW06032M40JNE
A
R13
1
10.0 kΩ
Resistor, 10.0 k, 1%, 0.1 W, AEC-Q200 Grade 0, 0603
0603
CRCW06034K70JNE
A
34
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
Schematic and Bill of Materials
Table 5-1. Bill of Materials (continued)
REF DES
QTY
VALUE
R14, R17
2
1.5 MΩ
R16
1
R18
SIZE
PART NUMBER
Resistor, 1.5 M, 5%, 0.1 W, AEC-Q200 Grade 0, 0603
0603
CRCW06031M50JNE
A
620 Ω
Resistor, 620, 1%, 0.1 W, 0603
0603
RC0603FR-07620RL
1
5.6 MΩ
Resistor, 5.6 M, 5%, 0.1 W, AEC-Q200 Grade 0, 0603
0603
CRCW06035M60JNE
A
R19
1
500 kΩ
Trimmer, 500 kΩ, 0.5W, TH
R20
1
R22, R23
2
S1
1
SH-J1, SH-J2,
SH-J3, SH-J4,
SH-J5, SH-J6,
SH-J7, SH-J8
TP1, TP3, TP4,
TP7, TP8,
TP11, TP12,
TP13, TP14,
TP16, TP17,
TP20, TP21,
TP22, TP23,
TP24, TP25,
TP26, TP27,
TP30, TP31,
TP33, TP34,
TP35, TP36
DESCRIPTION
1.00 MΩ Resistor, 1.00 M, 1%, 0.1 W, AEC-Q200 Grade 0, 0603
10 MΩ
Resistor, 10 M, 5%, 0.1 W, AEC-Q200 Grade 0, 0603
375×190×375mi 3386P-1-504LF
l
0603
CRCW06031M00FKE
A
0603
CRCW060310M0JNE
A
Switch, Slide, SPST 4 poles, SMT
SW, SMT Half
Pitch 4SPST,
5.8×2.7×6.25
mm
Shunt, 100 mil, Flash Gold, Black
Closed Top
100mil Shunt
218-4LPST
SPC02SYAN
8
1×2
5010
25
Test Point, Multipurpose, Red, TH
Red
Multipurpose
Testpoint
Black
Multipurpose
Testpoint
TP9, TP18,
TP19, TP28,
TP32, TP37,
TP38
5
Test Point, Multipurpose, Black, TH
U1
1
TPS8802DCP, DCP0038A (HTSSOP-38)
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
DCP0038A
5011
TPS8802DCP
Using the TPS8802EVM
Copyright © 2022 Texas Instruments Incorporated
35
Revision History
www.ti.com
6 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (May 2020) to Revision B (July 2022)
Page
• Added Section Abstract ..................................................................................................................................... 1
• Added Section Trademarks ............................................................................................................................... 2
• Updated the numbering format for tables, figures, and cross-references throughout the document..................3
• Added Section 3.4 ........................................................................................................................................... 21
• Added Section 3.4.1 ........................................................................................................................................ 21
• Added Section 3.4.2 ........................................................................................................................................ 24
• Added Section 3.4.3 ........................................................................................................................................ 26
Changes from Revision * (October 2019) to Revision A (May 2020)
Page
• Added Figure 3-4 ............................................................................................................................................... 9
• Added recommendation to install a 470 kΩ resistor connecting PREF to VINT in Section 3.2 ....................... 13
• Updated silkscreen labels in Figure 4-1 ...........................................................................................................29
• Added Figure 4-2 ............................................................................................................................................. 29
• Added Figure 4-3 ............................................................................................................................................. 29
• Updated PCB revision to CSTM002A in Figure 4-4 .........................................................................................29
• Added recommendation to install a 470 kΩ resistor connecting PREF to VINT in Figure 5-1 .........................33
• Changed R13 to 10.0 kΩ, changed C17 to 1nF, de-populated R15, C19, TP5, TP6 in Figure 5-1 ................. 33
• Changed C17 value to 1000 pF in Table 5-1 ................................................................................................... 34
• Changed R13 value to 10.0 kΩ in Table 5-1 .................................................................................................... 34
• Deleted R15, C19, TP5, TP6 in Table 5-1 ....................................................................................................... 34
36
Using the TPS8802EVM
SLVUBR8B – OCTOBER 2019 – REVISED JULY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
