Product
Folder
Sample &
Buy
Tools &
Software
Technical
Documents
Support &
Community
TPS92411, TPS92411P
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
TPS92411x Floating Switch for Offline AC Linear Direct Drive of LEDs with Low Ripple
Current
1 Features
•
1
•
•
•
•
•
•
•
•
•
High-Performance Solution for Driving LEDs from
AC Mains
Simplifies Design of Phase Dimmable LED Driver
with High Power Factor, Low Total Harmonic
Distortion, and Low Current Ripple
Suitable for LED Luminaires up to 70+ W
Input Voltage Range: 7.5 V to 100 V
Stackable 100 V, 2-Ω MOSFET Building Block
Controlled Switch Open and Close Transitions
Minimize EMI
Designed for use with the TPS92410 or with a
Discrete Linear Regulator
Input Undervoltage Protection
Output Overvoltage Protection (TPS92411P)
Low IQ: 200 µA (typ)
Device Information(1)
PART NUMBER
TPS92411,
TPS92411P
PACKAGE
BODY SIZE (NOM)
SOT-23 (5)
2.90 mm x 1.60 mm
SO PowerPAD (8)
4.89 mm x 3.90 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
VIN
DRAIN
TPS92411
120 VRMS
RSET
±
+
RSNS
VIN
VS
DRAIN
TPS92411
2 Applications
•
•
•
LED Lamps and Light Bulbs
LED Luminaires
Downlights
3 Description
The TPS92411 is a 100-V floating MOSFET switch
for use in offline LED lighting applications. The device
is used in conjunction with a current regulator that
can achieve a power factor greater than 0.9 to create
a LED drive solution with low-ripple current. When
properly
designed,
solution
performance
is
comparable to traditional flyback, buck or boostbased AC/DC LED drivers. The approach requires no
inductive components, thus saving size and cost.
Slew-controlled low-frequency operation of the
TPS92411 switches creates very little EMI. Detailed
operation is described in the Application Information
section.
RSET
RSNS
VIN
VS
DRAIN
TPS92411
RSET
RSNS
VS
Package options include SOT23-5 and PSOP-8
allowing the user to optimize for small size or scale
for high power. Using the PSOP-8 package, design of
LED luminaires up to 70 W or more is possible. Other
features include a UVLO circuit to monitor when the
device has sufficient voltage to operate properly and
over-voltage protection (TPS92411P).
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS92411, TPS92411P
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
6.1
6.2
6.3
6.4
6.5
6.6
3
3
4
4
4
6
Absolute Maximum Ratings ......................................
Handling Ratings.......................................................
Recommended Operating Conditions.......................
Thermal Information .................................................
Electrical Characteristics..........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 8
7.1 Overview ................................................................... 8
7.2 Functional Block Diagram ......................................... 8
7.3 Feature Description................................................... 9
7.4 Device Functional Modes........................................ 10
8
Application and Implementation ........................ 11
8.1 Application Information............................................ 11
8.2 Typical Application .................................................. 12
9 Power Supply Recommendations...................... 18
10 Layout................................................................... 18
10.1 Layout Guidelines ................................................. 18
10.2 Layout Example .................................................... 18
11 Device and Documentation Support ................. 19
11.1
11.2
11.3
11.4
Related Links ........................................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
19
19
19
19
12 Mechanical, Packaging, and Orderable
Information ........................................................... 19
4 Revision History
Changes from Revision A (May 2014) to Revision B
•
Page
Added Pin Configuration and Functions section, Handling Rating table, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information
section ................................................................................................................................................................................... 1
Changes from Original (October 2013) to Revision A
Page
•
Deleted preview designation for DDA package...................................................................................................................... 3
•
Added availablity information for DDA package ..................................................................................................................... 3
2
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
TPS92411, TPS92411P
www.ti.com
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
5 Pin Configuration and Functions
DBV (SOT23-5) PACKAGE
5 PIN
(TOP VIEW)
RSET
1
VS
2
3
VIN
5
DDA (SO-8 Power-Pad) PACKAGE
8 PIN
(TOP VIEW)
RSNS
DRAIN
4
VIN
1
8
DRAIN
N/C
2
7
N/C
RSET
3
6
N/C
VS
4
5
RSNS
Pin Functions
PIN
NO.
NAME
I/O
DESCRIPTION
4
O
Drain of the internal switch.
—
—
DDA
DBV
DRAIN
8
N/C
2
N/C
6
N/C
7
VIN
1
3
I
VS
4
2
I/O
Source of the internal switch. This pin is also the device floating ground.
RSET
3
1
I/O
A resistor connected between the RSET pin and the VIN pin sets the rising
threshold to open the switch.
RSNS
5
5
I/O
A resistor connected between the RSNS pin to system ground senses the VS
voltage relative to system ground.
Not internally connected.
Exposed Themal Pad
Positive power supply for the device.
Connect to VS pin directly beneath the device.
6 Specifications
6.1 Absolute Maximum Ratings
All voltages are with respect to VS, –40 °C < TJ = TA ≤ 150 °C. All currents are positive into and negative out of the specified
terminal (unless otherwise noted).
MIN
MAX
Supply voltage
VIN
–0.3
105
Switch voltage
DRAIN
–0.3
105
Junction temperature
TJ
–40
165
UNIT
V
ºC
6.2 Handling Ratings
Tstg
Storage temperature range
V(ESD)
(1)
(2)
Electrostatic discharge
MIN
MAX
UNIT
–65
150
°C
1
kV
250
V
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins (1)
Charged device model (CDM), per JEDEC specification
JESD22-C101, all pins (2)
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
Submit Documentation Feedback
3
TPS92411, TPS92411P
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
www.ti.com
6.3 Recommended Operating Conditions
Over operating free-air temperature range (unless otherwise noted)
MIN
VIN
Input voltage
TJ
Operating junction temperature
TYP
MAX
TPS92411P
7.5
94
TPS92411
7.5
100
–40
25
UNIT
V
150
°C
6.4 Thermal Information
TPS92411
THERMAL METRIC (1)
DBV
DDA
5 PINS
8 PINS
θJA
Junction-to-ambient thermal resistance (2)
209.8
58.6
θJCtop
Junction-to-case (top) thermal resistance (3)
125.2
72
(4)
θJB
Junction-to-board thermal resistance
38
39.1
ψJT
Junction-to-top characterization parameter (5)
15.6
21.6
ψJB
Junction-to-board characterization parameter (6)
37.1
39.1
θJCbot
Junction-to-case (bottom) thermal resistance (7)
N/A
15
(1)
(2)
(3)
(4)
(5)
(6)
(7)
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as
specified in JESD51-7, in an environment described in JESD51-2a.
The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specified JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB
temperature, as described in JESD51-8.
The junction-to-top characterization parameter, θJT, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-board characterization parameter, θJB, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific
JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
6.5
Electrical Characteristics
Unless otherwise specified –40 °C ≤ TJ = TA ≤ 150 °C, (VVIN – VVS) = 30 V, RRSET = RRSNS = Open, all voltages are with
respect to VS.
PARAMETER
TEST CONDITIONS
MIN
TYP
95
100
MAX
UNIT
INPUT SUPPLY (VIN)
Rising threshold
Input overvoltage
protection
VIN(ovp)
TPS92411P Falling threshold
96
Hysteresis
IQ
Bias current
VIN(uvlo)
Input undervoltage lockout
VIN(hys)
Input UVLO hysteresis
V
4
Rising threshold
200
400
6.5
7
370
μA
V
mV
SWITCH CONTROL (RSNS, RSET)
IRSNS
RSNS threshold current
–3.3
–4
–4.9
μA
VRSNS_OS
RSNS offset voltage
165
210
255
mV
VRSET
RSET threshold voltage
1.2
1.25
1.3
V
IRSNS = –20 μA, (VRSET – VVS) = 1.5 V
–9.3
–10
–10.7
IRSET
RSET current
IRSNS = –40 μA, (VRSET – VVS) = 1.5 V
–19
–20
–21
–47.9
–50
–52.1
1
2
2.5
IRSNS = –100 μA, (VRSET – VVS) = 1.5 V
μA
SWITCH (DRAIN, VS)
RDS(on)
4
On-resistance
Submit Documentation Feedback
IDRAIN = 100 mA, TJ = 25°C
Ω
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
TPS92411, TPS92411P
www.ti.com
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
Electrical Characteristics (continued)
Unless otherwise specified –40 °C ≤ TJ = TA ≤ 150 °C, (VVIN – VVS) = 30 V, RRSET = RRSNS = Open, all voltages are with
respect to VS.
PARAMETER
TEST CONDITIONS
dv/dt(ON)
Switch ON slew rate
(VDRAIN – VVS) falling 36 V to 4 V,
ISW = 100 mA
dv/dt(OFF)
Switch OFF slew rate
(VDRAIN – VVS) = rising 4 V to 36 V,
ISW = 100 mA
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
MIN
TYP
MAX
UNIT
1
0.5
Submit Documentation Feedback
V/μs
5
TPS92411, TPS92411P
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
www.ti.com
6.6 Typical Characteristics
Unless otherwise stated, –40 °C ≤ TA = TJ ≤ 150 °C, (VVIN – VVS) = 30 V, all voltages are with respect to VS.
10
VIN − VS UVLO Falling (V)
VIN − VS UVLO Rising (V)
10
8
6
4
2
0
−40 −25 −10 5
8
6
4
2
0
−40 −25 −10 5
20 35 50 65 80 95 110 125 140 155
Junction Temperature (°C)
G000
Figure 1. UVLO vs. Temperature
Figure 2. UVLO vs. Temperature
2
0
RSNS Threshold Current (µA)
RSET Threshold (V)
1.8
1.5
1.2
1
0.8
0.5
0.2
0
−40 −25 −10 5
−2
−4
−6
−8
−10
−40 −25 −10 5
20 35 50 65 80 95 110 125 140 155
Junction Temperature (°C)
G002
200
4
180
3
2
1
0
−40 −25 −10 5
20 35 50 65 80 95 110 125 140 155
Junction Temperature (°C)
G003
Figure 4. RSNS Threshold Current vs. Temperature
5
Supply Current (µA)
Switch ON Resistance (Ω)
Figure 3. RSET Threshold vs. Temperature
160
140
120
20 35 50 65 80 95 110 125 140 155
Junction Temperature (°C)
G004
Figure 5. Switch On-Resistance (RDS(on)) vs. Temperature
6
20 35 50 65 80 95 110 125 140 155
Junction Temperature (°C)
G001
Submit Documentation Feedback
100
−40 −25 −10 5
20 35 50 65 80 95 110 125 140 155
Junction Temperature (°C)
G005
Figure 6. Input Voltage Quiescent Current vs. Temperature
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
TPS92411, TPS92411P
www.ti.com
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
Typical Characteristics (continued)
Unless otherwise stated, –40 °C ≤ TA = TJ ≤ 150 °C, (VVIN – VVS) = 30 V, all voltages are with respect to VS.
110
VIN − VS Voltage (V)
106
102
98
94
TPS92411P
90
−40 −25 −10 5
20 35 50 65 80 95 110 125 140 155
Junction Temperature (°C)
G006
Figure 7. (VVIN – VVS) Overvoltage Threshold vs. Temperature
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
Submit Documentation Feedback
7
TPS92411, TPS92411P
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
www.ti.com
7 Detailed Description
7.1 Overview
The TPS92411 is an advanced, floating driver specifically designed for use with a linear regulator in low-power
offline LED lighting applications. It integrates an on-board 100-V MOSFET switch to shunt LED current as the
line transitions. As the line transitions through the cycle, the device monitors critical nodes for zero cross at which
time the internal switch is either opened or shorted to steer the current through or away from the LED stack. The
TPS92411 does not directly control output power or LED current, it just directs current to the LED stack or
bypasses the LED stack.
7.2 Functional Block Diagram
VIN
DRAIN
TPS92411
5 0
VCC
RSET
+
±
+
+
±
1.25 V
1x
2x
1x
VDD
VDD
Buffer
12 V
VIN UVLO
6.5 V/6.13 V
Reference
UVLO
VS
VCC
UVLO
VS
1x
1x
2
R
210 mV
S
+
OV
Q
Set dominant
+
±
2 µA
VS
VS
RSNS
VS
Figure 8. TPS92411 Block Diagram
8
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
TPS92411, TPS92411P
www.ti.com
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
Functional Block Diagram (continued)
VIN
DRAIN
TPS92411P
3.95 0
5 0
VCC
RSET
+
±
+
+
±
1.25 V
1x
2x
1x
VDD
VDD
Buffer
+
50 N
12 V
VIN UVLO
6.5 V/6.13 V
VS
VS
VS
1x
S
+
1.25 V
VS
VCC
2
R
210 mV
+
±
UVLO
UVLO
1x
OV
Reference
OV
Q
Set dominant
+
±
2 µA
VS
VS
RSNS
VS
Figure 9. TPS92411P Block Diagram
7.3 Feature Description
7.3.1 Overvoltage Protection (OVP)
Overvoltage protection (OVP) in the TPS92411P version protects the device as well as the LEDs and storage
capacitor. The OVP is set at approximately 100 V (VVIN – VVS) and closes the internal switch when the threshold
voltage is reached. For this reason LED stack voltages of 94 V or less are recommended. Higher voltages can
be used with the TPS92411 version but tolerances must be considered to ensure that the 105 V absolute
maximum rating is not exceeded.
7.3.2 Input Undervoltage Lockout (UVLO)
The TPS92411 includes input UVLO. The UVLO prevents the device from operation until the VIN pin voltage with
respect to VS exceeds 6.5 V and ensures the device behaves properly when enabled.
7.3.3 LED Capacitor
A capacitor is required across each LED stack to provide current to the LEDs during the switch ON time. Refer to
the available calculator software (SLVC516 for 120-V applications or SLVC517 for 230-V applications) for
calculating the minimum value required for any particular application. The software calculates the minimum value
required for a particular application, but best performance is acheived by using as much capacitance as possible
given size and cost constraints. These design tools also calculate a minimum value for any given current ripple
percent or flicker index desired for the particular application.
7.3.4 Blocking Diode
A blocking diode is required between the drain of the switch (DRAIN) and the anode of the LED stack. This
prevents the LED capacitor from discharging through the switch during the switch ON time instead allowing it to
discharge through the LED stack. This diode should be rated for 200 V reverse voltage and capable of forward
currents as high as the average linear regulator current setting.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
Submit Documentation Feedback
9
TPS92411, TPS92411P
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
www.ti.com
7.4 Device Functional Modes
The TPS92411P has 4 functional modes while the TPS92411 has 3:
7.4.1 Input UVLO
As described in the previous section the device and internal switch will remain off until VIN is 6.5V or greater with
respect to VS.
7.4.2 Operating with Internal Switch ON
After the device crosses the UVLO threshold the internal switch will turn on and remain on until the voltage at the
VIN pin exceeds the threshold voltage set by the RSET resistor.
7.4.3 Operating with Internal Switch OFF
When the RSET threshold voltage is exceeded on the VIN pin the internal switch will turn off forcing all the
current to flow through the LEDs and charge the LED capacitor. The switch will remain off until the VS pin drops
below the threshold voltage set by RSNS or an overvoltage event occurs (TPS92411P only).
7.4.4 Overvoltage Operation (TPS92411P)
If an LED fails open or a string voltage exceeding the OVP level is used the device will enter OVP operation. The
internal switch will close and remain closed until the VIN voltage with respect to the VS pin drops low enough to
engage normal operation again.
10
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
TPS92411, TPS92411P
www.ti.com
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
8 Application and Implementation
8.1 Application Information
The TPS92411 is an advanced, floating driver specifically designed for use with a linear regulator in low-power
offline LED lighting applications. It integrates an on-board 100-V MOSFET switch to shunt LED current as the
line transitions. As the line transitions through the cycle, the device monitors critical nodes for zero cross at which
time the internal switch is either opened or shorted to steer the current through or away from the LED stack. Use
the following design procedure to select components for the TPS92411. The following calculators may also be
used to select components for the TPS92411:
• SLVC579 for 120-V applications using the TPS92410
• SLVC580 for 230-V applications using the TPS92410
• SLVC516 for 120-V applications using a discrete linear regulator
• SLVC517 for 230-V applications using a discrete linear regulator
PSpice and TINA-TI models are also available. The following are typical applications using the TPS92411 for
both 120-V and 230-V applications using a discrete linear regulator.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
Submit Documentation Feedback
11
TPS92411, TPS92411P
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
www.ti.com
8.2 Typical Application
8.2.1 120-VAC, Phase Dimmable 11.5-W Input with Discrete Linear Regulator
22
200 V
VIN
120 VRMS
1.82 0
±
+
DRAIN
TPS92411
RSET
1 0
RSNS
33 µF
100 V
VS
200 V
VIN
1.65 0
0.22 µF
250 V
DRAIN
TPS92411
68 µF
50 V
RSET
0.1 µF
250 V
1 0
RSNS
VS
442
200 V
VIN
1.43 0
DRAIN
TPS92411
120 µF
25 V
RSET
1 0
RSNS
VS
200 N
91 V
732 N
44.2 N
90.9 N
499 N
Q1
600 V
2A
2 0
12 V 0.01 µF
0.22 µF
Q2
200 mW
5 N
RCS
24
1 N
0.1 µF
Figure 10. 120-VAC, Phase Dimmable 11.5-W Input with Discrete Linear Regulator
8.2.1.1 Design Requirements
For the 120-V application shown in Figure 10 the highest efficiency is obtained by using a high-voltage total LED
stack to reduce losses in the linear regulator FET. The best current sharing efficiency between stacks can be
achieved by using the lowest voltage stack at the bottom and making each stack voltage above 2 times the
voltage of the stack below it. In this example 20-V LEDs are used. This effectively gives the lowest stack a total
of 20 V, the middle stack a total of 40 V, and the upper stack a total of 80 V. The RSNS resistor is used to set a
12
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
TPS92411, TPS92411P
www.ti.com
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
Typical Application (continued)
low voltage point so that when the VS pin voltage falls below this threshold (either from the AC line falling or a
higher voltage stack switch above it turning OFF) the TPS92411 switch turns ON and bypasses the LEDs. During
the ON-time, the LEDs are supplied current from the capacitor. The RSET voltage is used to set a threshold to
detect when the input voltage crosses this threshold it turns OFF the switch and allows the LEDs to conduct
current from the line and charge the bypass capacitor.
8.2.1.2 Detailed Design Procedure
• Set VRSNS for all three TPS92411 devices at 4 V
• Set VRSET for the bottom stack at 26 V (20 V stack plus 6 V headroom)
• Set VRSET for the middle stack at 46 V (40 V stack plus 6 V headroom)
• Set VRSET for the top stack at 86 V (80 V stack plus 6 V headroom)
Switching order as the rectified AC line voltage increases is shown in Table 1. Figure 11 illustrates when each
switch turns ON or OFF.
8.2.1.2.1 Setting the Switching Thresholds (RSNS, RSET)
The TPS92411 features two threshold settings to allow for proper LED control. The first setting determines when
the internal switch turns off and allows current to charge the capacitor and flow through the LEDs. The second
setting determines when the switch turns on to shunt the LEDs and allow the capacitor to supply current. The
lower switch turn-on threshold (VSNS) should be set first using a resistor (RRSNS) from the RSNS pin to system
ground. For best efficiency set this threshold between 4 V and 6 V. Then the upper switch turn-off threshold (VVS)
can be set using a resistor (RRSET) from the RSET pin to the VIN pin. Set this threshold approximately 6 V to 10
V above the LED stack voltage (VLED). The RSET threshold should be greater than the LED stack voltage plus
the value of the RSNS threshold to prevent errant switching. These thresholds can be set with resistance
calculated using Equation 1 and Equation 2.
+ 0.21V
V
RSNS = SNS
IRSNS
(1)
RRSET =
(VLED - 1.24 V )´ 2 ´ RSNS
VVS + 0.21V
(2)
Table 1. Switching Order on Rising Edge of Rectified 120-VAC
(1) (2)
STACK
(1)
(2)
TOP 80-V
MIDDLE 40-V
BOTTOM 20-V
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
0 denotes switch ON and LEDs bypassed and supplied by the capacitor.
1 denotes switch OFF and LEDs conducting from the line, capacitor charging up.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
Submit Documentation Feedback
13
TPS92411, TPS92411P
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
www.ti.com
Rectified AC (V)
Voltage trip points do not
include diode drops
146
111
126
110
110
106
144
101
101
86
100
100
66
84
010
010
26
104
011
011
46
124
64
001
001
000
44
000
24
Time
Figure 11. Switching Order on Rectified 120-VAC Waveform
The linear regulator in Figure 11 generates a current sense RMS voltage of approximately 2.3 V. The linear
regulator RMS current is equal to the input current drawn from the AC line. For example, for a 11.5-W input
power system the input current should be approximately 0.095 A and a 24-Ω resistor should be chosen for RCS.
Other input power levels (PIN) can be obtained using Equation 3.
120 VRMS ´ 2.3VRMS
RCS =
PIN
(3)
8.2.1.3 Application Curve
1.00
0.99
0.98
Power Factor
0.97
0.96
0.95
0.94
0.93
0.92
0.91
0.90
190
200
210
220
230
240
250
Input Voltage (VAC)
260
C001
Figure 12. Power Factor vs. Input Voltage
14
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
TPS92411, TPS92411P
www.ti.com
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
8.2.2 230-VAC, Phase Dimmable 16-W Input with Discrete Linear Regulator
200 V
1 N
1 0
Q3
200 V
VGS = 4 V
680 pF
10 N
22 µF
200 V
68
VIN
230 VRMS
2.8 0
±
DRAIN
TPS92411
+
12 V 12 V
RSET
0.1 µF
100 V
1.5 0
RSNS
VS
200 V
VIN
2.67 0
0.15 µF
400 V
47 µF
100 V
DRAIN
TPS92411
RSET
0.033 µF
400 V
1.5 0
RSNS
VS
550
200 V
VIN
2.37 0
DRAIN
TPS92411
100 µF
50 V
RSET
1.5 0
RSNS
VS
442 N
100 N
0.22 µF
68 V
100 N
Q1
600 V
2A
12 V 0.022 µF
0.1 µF
Q2
200 mW
4.99 N
249 N
1 0
10 N
RCS
34.8
Figure 13. 230-VAC, Phase Dimmable 16-W Input with Discrete Linear Regulator
8.2.2.1 Design Requirements
In the 230-V application shown in Figure 13, the highest efficiency can be obtained by using a high-voltage total
LED stack to reduce losses in the linear regulator FET. The best current sharing between stacks can be
achieved by using the lowest voltage stack at the bottom and making each stack voltage above that two times
that of the stack below it (as in described in the 120-V application). In this example, very good results can be
obtained by setting the lowest stack at 40 V, the middle stack at 80 V, and adding a high-voltage cascode FET
with the top stack and using 160 V. Use the RSNS pin to set a low voltage point so that when the VS pin of the
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
Submit Documentation Feedback
15
TPS92411, TPS92411P
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
www.ti.com
device falls below this threshold (either from the AC line falling or a higher voltage stack switch above it turning
OFF) the TPS92411 switch turns ON and bypasses the LEDs. During the ON-time, the capacitor supplies current
to the LEDs. The RSET voltage threshold for a 230-V application is generally set to approximately 8 V to 12 V
above the LED stack voltage connected across the TPS92411 (for an RSNS voltage of 6 V). This threshold is
higher than in the typical 120-V application to allow more headroom.
8.2.2.2 Detailed Design Procedure
• Set VRSNS for all three TPS92411 devices at 6 V
• Set VRSET for the bottom stack at 49 V (40 V stack plus 9 V headroom)
• Set VRSET for the middle stack at 89 V (80 V stack plus 9 V headroom)
• Set VRSET for the top stack at 169 V (160 V stack plus 9 V headroom)
Switching order as the rectified AC line voltage increases is shown in Table 2. Figure 14 illustrates when each
switch turns ON or OFF.
Table 2. Switching Order on Rising Edge of the Rectified 230-VAC
Waveform (1) (2)
STACK
(1)
(2)
TOP 160-V
MIDDLE 80-V
BOTTOM 40-V
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
0 denotes switch ON and LEDs bypassed and supplied by the capacitor.
1 denotes switch OFF and LEDs conducting from the line, capacitor charging up.
Rectified AC (V)
Voltage trip points do not
include diode drops
289
111
249
209
49
246
100
100
129
286
101
101
169
89
110
110
206
011
011
166
010
010
126
001
001
000
000
86
46
Time
Figure 14. Switching Order on Rising Edge of the Rectified 230-VAC Waveform
The linear regulator in Figure 14 generates a current sense RMS voltage of 2.44 V. The linear regulator RMS
current is equal to the input current drawn from the AC line. For example, for a 16-W input power system the
input current should be approximately 0.07 A and a 34.8-Ω resistor should be chosen for RCS. Other input power
levels (PIN) can be calculated using Equation 4.
230 VRMS ´ 2.44VRMS
RCS =
PIN
(4)
16
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
TPS92411, TPS92411P
www.ti.com
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
8.2.2.3 Application Curve
1.00
0.99
0.98
Power Factor
0.97
0.96
0.95
0.94
0.93
0.92
0.91
0.90
190
200
210
220
230
240
250
Input Voltage (VAC)
260
C001
Figure 15. Power Factor Input Voltage
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
Submit Documentation Feedback
17
TPS92411, TPS92411P
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
www.ti.com
9 Power Supply Recommendations
For testing purposes any benchtop adjustable AC power supply with a power rating higher than what is required
by the circuit is suitable. An example would be an Hewlett Packard 6811B or equivalent. An isolated supply is
recommended for safety purposes.
10 Layout
10.1 Layout Guidelines
The TPS92411 allows for a simple layout, however some considerations should be taken. The RSET resistor
should be connected directly between the RSET pin and VIN pin as close to the device as possible. The trace
between the resistor and the RSET pin should be as short as possible. The trace from the RSNS pin to the
RSNS resistor should also be as short as possible to minimize parasitic capacitances. The blocking diode should
be placed between the DRAIN pin and the VIN pin and also located close to the device. Placement of the LED
capacitor may depend on the physical design of the application, however it should be placed as close to the
TPS92411 as the design allows to minimize parasitic inductances.
10.2 Layout Example
1-RSET 5-RSNS
LED-/VS
System
GND
2-VS
3-VIN 4-DRAIN
To rectified AC or VS of
TPS92411 above
LED+
Figure 16. Recommended Component Placement (DBV)
To rectified AC or VS of
TPS92411 above
LED+
LED-/VS
1-VIN
8-DRAIN
2-NC
7-NC
3-RSET
6-NC
4-VS
System
GND
5-RSNS
Figure 17. Recommended Component Placement (DDA)
18
Submit Documentation Feedback
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
TPS92411, TPS92411P
www.ti.com
SLUSBQ6B – OCTOBER 2013 – REVISED JULY 2014
11 Device and Documentation Support
11.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 3. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
TPS92411
Click here
Click here
Click here
Click here
Click here
TPS92411P
Click here
Click here
Click here
Click here
Click here
11.2 Trademarks
All trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: TPS92411 TPS92411P
Submit Documentation Feedback
19
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TPS92411DBVR
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 150
PB9Q
TPS92411DBVT
ACTIVE
SOT-23
DBV
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 150
PB9Q
TPS92411DDA
ACTIVE SO PowerPAD
DDA
8
75
RoHS & Green
NIPDAUAG
Level-2-260C-1 YEAR
-40 to 150
92411
TPS92411DDAR
ACTIVE SO PowerPAD
DDA
8
2500
RoHS & Green
NIPDAUAG
Level-2-260C-1 YEAR
-40 to 150
92411
TPS92411PDBVR
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 150
PB8Q
TPS92411PDBVT
ACTIVE
SOT-23
DBV
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 150
PB8Q
TPS92411PDDA
ACTIVE SO PowerPAD
DDA
8
75
RoHS & Green
NIPDAUAG
Level-2-260C-1 YEAR
-40 to 150
92411P
TPS92411PDDAR
ACTIVE SO PowerPAD
DDA
8
2500
RoHS & Green
NIPDAUAG
Level-2-260C-1 YEAR
-40 to 150
92411P
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of