TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
FEATURES
•
•
•
•
•
•
•
•
•
•
Compatible With HDMI v1.2a (Type A) DVI 1.0
High-Speed Digital Interface
– Wide Bandwidth of Over 1.65 Gbps
(Bandwidth 1.8 Gbps Typ)
– 165-MHz Speed Operation
– Serial Data Stream at 10× Pixel Clock Rate
– Supports All Video Formats up to 1080p
and SXGA (1280 × 1024 at 75 Hz)
– Total Raw Capacity 4.95 Gbps (Single Link)
– HDCP Compatible
Low Crosstalk (XTALK = –41 dB Typ)
Low Bit-to-Bit Skew (tsk(o) = 0.2 ns Max)
Low and Flat ON-State Resistance
(ron = 4 Ω Typ, ron(flat) = 0.7 Ω Typ)
Low Input/Output Capacitance
(CON = 10 pF Typ)
Rail-to-Rail Switching on Data I/O Ports
(0 to 5 V)
VDD Operating Range From 3 V to 3.6 V
Ioff Supports Partial-Power-Down Mode
Operation
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Performance Tested Per JESD 22
– 2000-V Human-Body Model
(A114-B, Class II)
– 1000-V Charged-Device Model (C101)
DGG OR DGV PACKAGE
(TOP VIEW)
VDD
A0
GND
A1
GND
VDD
GND
A2
GND
A3
GND
VDD
GND
NC
A4
GND
A5
GND
VDD
GND
A6
GND
A7
SEL
1
48
2
47
3
46
4
45
5
44
6
43
7
42
8
41
9
40
10
39
11
38
12
37
13
36
14
35
15
34
16
33
17
32
18
31
19
30
20
29
21
28
22
27
23
26
24
25
0B1
1B1
GND
0B2
1B2
GND
2B1
3B1
GND
2B2
3B2
GND
VDD
4B1
5B1
GND
4B2
5B2
GND
6B1
7B1
GND
6B2
7B2
NC − No internal connection
APPLICATIONS
•
•
Digital Video Signal Switching
Differential DVI, HDMI Signal Multiplexing for
Audio/Video Receivers and High-Definition
Television (HDTV)
DESCRIPTION/ORDERING INFORMATION
The TS3DV416 is a 16-bit to 8-bit multiplexer/demultiplexer digital video switch with a single select (SEL) input.
SEL controls the data path of the multiplexer/demultiplexer.
The device provides a low and flat ON-state resistance (ron) and an excellent ON-state resistance match. Low
input/output capacitance, high bandwidth, low skew, and low crosstalk among channels make this device
suitable for various digital video applications, such as DVI and HDMI.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2006, Texas Instruments Incorporated
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
ORDERING INFORMATION
PACKAGE (1)
TA
–40°C to 85°C
(1)
ORDERABLE PART NUMBER
TSSOP – DGG
Tape and reel
TS3DV416DGGR
TS3DV416
TVSOP – DGV
Tape and reel
TS3DV416DGVR
SD416
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
TYPICAL APPLICATION
DVD Player
Digital TV
TS3DV416
STB
DVI
Receiver
FUNCTION TABLE
INPUT
SEL
INPUT/
OUTPUT
An
L
nB1
An = nB1
nB2 high-impedance mode
H
nB2
An = nB2
nB1 high-impedance mode
FUNCTION
PIN DESCRIPTION
2
TOP-SIDE MARKING
NAME
DESCRIPTION
An
Data I/O
nBm
Data I/O
SEL
Select input
Submit Documentation Feedback
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
LOGIC DIAGRAM (POSITIVE LOGIC)
2
48
4
47
0B1
A0
1B1
A1
45
0B2
44
1B2
8
42
10
41
2B1
A2
3B1
A3
39
2B2
38
3B2
15
35
17
34
4B1
A4
5B1
A5
32
4B2
31
5B2
21
29
6B1
A6
23
28
7B1
A7
26
6B2
25
7B2
SEL
24
Submit Documentation Feedback
3
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VDD
Supply voltage range
–0.5
4.6
V
VIN
Control input voltage range (2) (3)
–0.5
7
V
VI/O
Switch I/O voltage
range (2) (3) (4)
IIK
Control input clamp current
VIN < 0
–50
mA
II/OK
I/O port clamp current
VI/O < 0
–50
mA
±128
mA
±100
mA
II/O
ON-state switch
–0.5
current (5)
Continuous current through VDD or GND
θJA
Package thermal impedance (6)
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
(5)
(6)
7
DGG package
70
DGV package
58
–65
UNIT
V
°C/W
°C
150
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to ground, unless otherwise specified.
The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
VI and VO are used to denote specific conditions for VI/O.
II and IO are used to denote specific conditions for II/O.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions (1)
MAX
UNIT
VDD
Supply voltage
3
3.6
V
VIH
High-level control input voltage (SEL)
2
5.5
V
VIL
Low-level control input voltage (SEL)
0
0.8
V
VI/o
Input/output voltage
0
5.5
V
TA
Operating free-air temperature
–40
85
°C
(1)
4
MIN
All unused inputs of the device must be held at VDD or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
Submit Documentation Feedback
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
Electrical Characteristics
(1)
for high-frequency switching over recommended operating free-air temperature range, VDD = 3.3 V ± 0.3 V
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP (2)
MAX
–0.7
–1.2
V
UNIT
VIK
SEL
VDD = 3.6 V,
IIN = –18 mA
IIH
SEL
VDD = 3.6 V,
VIN = VDD
±1
µA
IIL
SEL
VDD = 3.6 V,
VIN = GND
±1
µA
Ioff
VDD = 0,
VO = 0 to 3.6 V,
VI = 0
IDD
VDD = 3.6 V,
II/O = 0,
Switch ON or OFF
CIN
SEL
f = 1 MHz,
VIN = 0
COFF
B port
1
µA
250
600
µA
2.5
3
pF
VI = 0,
f = 1 MHz,
Outputs open,
Switch OFF
3.5
4
pF
CON
VI = 0,
f = 1 MHz,
Outputs open,
Switch ON
10
10.9
pF
ron
VDD = 3 V,
1.5 V ≤ VI ≤ VDD,
IO = –40 mA
4
8
Ω
VDD = 3 V,
VI = 1.5 V and VDD,
IO = –40 mA
0.7
VDD = 3 V,
1.5 V ≤ VI ≤ VDD,
IO = –40 mA
0.2
1.2
TYP (1)
MAX
ron(flat)
(3)
∆ron (4)
(1)
(2)
(3)
(4)
Ω
Ω
VI, VO, II, and IO refer to I/O pins. VIN refers to the control inputs.
All typical values are at VDD = 3.3 V (unless otherwise noted), TA = 25°C.
ron(flat) is the difference of ron in a given channel at specified voltages.
∆ron is the difference of ron from center (A4, A5) ports to any other port.
Switching Characteristics
over recommended operating free-air temperature range, VDD = 3.3 V ± 0.3 V, RL = 200 Ω, CL = 10 pF
(unless otherwise noted) (see Figure 4 and Figure 5)
FROM
(INPUT)
TO
(OUTPUT)
A or B
B or A
SEL
A or B
1.5
tPHZ, tPLZ
SEL
A or B
1
tsk(o) (3)
A or B
B or A
PARAMETER
tpd
(2)
tPZH, tPZL
MIN
0.04
tsk(p) (4)
(1)
(2)
(3)
(4)
UNIT
ns
11.5
ns
8.5
ns
0.1
0.2
ns
0.1
0.2
ns
All typical values are at VDD = 3.3 V (unless otherwise noted), TA = 25°C.
The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load
capacitance when driven by an ideal voltage source (zero output impedance).
Output skew between center port (A4 to A5) to any other port
Skew between opposite transitions of the same output in a given device |tPHL– tPLH|
Dynamic Characteristics
over recommended operating free-air temperature range, VDD = 3.3 V ± 0.3 V (unless otherwise noted)
PARAMETER
(1)
TEST CONDITIONS
TYP (1)
UNIT
XTALK
RL = 100 Ω,
f = 250 MHz,
See Figure 7
–41
OIRR
RL = 100 Ω,
f = 250 MHz,
See Figure 8
–39
dB
BW
See Figure 6
900
MHz
dB
All typical values are at VDD = 3.3 V (unless otherwise noted), TA = 25°C.
Submit Documentation Feedback
5
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
OPERATING CHARACTERISTICS
0
−1
−2
Gain − dB
−3
−4
−5
−6
−7
−8
−9
1
10
100
1,000
10,000
Frequency − MHz
Gain at 900 MHz, −3 dB
Figure 1. Gain vs Frequency
0
−20
Off-Isolation − dB
−40
−60
−80
−100
−120
1
10
100
1,000
Frequency − MHz
OFF Isolation at 250 MHz, −39 dB
Figure 2. OFF Isolation vs Frequency
6
Submit Documentation Feedback
10,000
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
OPERATING CHARACTERISTICS (continued)
0
−20
Crosstalk − dB
−40
−60
−80
−100
−120
1
10
100
1,000
10,000
Frequency − MHz
Crosstalk at 250 MHz, −41 dB
Figure 3. Crosstalk vs Frequency
Submit Documentation Feedback
7
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
APPLICATION INFORMATION
1
−
TMDS Data 2
2
TMDS Data 2+
9
10
17
TMDS Data 1 −
18
TMDS Data 1+
23
24
TMDS Data 2 −
TMDS Data 2 −
Data 2+
TMDSTMDS
Data 2+
TMDS Data 1 −
TMDS Data 1 −
TMDS Data 1+
TMDS Data 1+
TMDS Data 0 −
TMDS Data 0 −
TMDS Data 0+
TMDS Data 0+
TMDS Clock+
TMDS Clock+
TMDS Clock −
TMDS Clock −
TMDS Data 0 −
DVI Connector 1
(Single Link)
TMDS Data 0+
TMDS Clock+
TMDS Clock −
1
To DVI Receiver
2
9
10
TMDS Data 2 −
1
TMDS Data 2+
2
TMDS Data 1 −
9
TMDS Data 1+
10
TS3DV416
Pin
Typical DVI Connector
1
9
4
5
6
7
8
10
2
11
3
12
13
14
15
16
17
18
19
20
21
22
23
24
C1 C2
C5
C3 C4
The TS3DV416 can be used to switch
between two digital video ports.
8
Name
DVI Connector Pin Assignments
Function
1
2
3
4
5
6
7
8
9
TMDS Data 2−
Digital red − (Link 1)
TMDS Data 2+
Digital red + (Link 1)
TMDS Data 1−
Digital green − (Link 1)
10
TMDS Data 1+
Digital green + (Link 1)
11
TMDS Data 1/3 shield
12
TMDS Data 3−
Digital blue − (Link 2)
13
TMDS Data 3+
Digital blue + (Link 2)
14
+5V
Power for monitor when in standby
15
Ground
Return for pin 14 and analog sync
16
Hot Plug Detect
17
TMDS data 0−
Digital blue − (Link 1) and digital sync
18
TMDS data 0+
Digital blue + (Link 1) and digital sync
19
TMDS data 0/5 shield
20
TMDS data 5−
Digital red − (Link 2)
21
TMDS data 5+
Digital red + (Link 2)
22
TMDS clock shield
23
TMDS clock+
Digital clock + (Links 1 and 2)
24
TMDS clock−
Digital clock − (Links 1 and 2)
C1
C2
C3
C4
C5
Analog Red
TMDS Data 2/4 shield
TMDS Data 4−
Digital green − (Link 2)
TMDS Data 4+
Digital green + (Link 2)
DDC clock
DDC data
Analog Vertical Sync
Analog Green
Analog Blue
Analog Horizontal Sync
Analog Ground
Return for R, G and B signals
Submit Documentation Feedback
17
TMDS Data 0
18
TMDS Data 0+
23
TMDS Clock+
23
24
TMDS Clock −
24
−
DVI Connector 2
(Single Link)
17
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
PARAMETER MEASUREMENT INFORMATION
(Enable and Disable Times)
VDD
Input Generator
VIN
50 Ω
50 Ω
VG1
TEST CIRCUIT
DUT
2 × VDD
Input Generator
VI
S1
RL
VO
Open
GND
50 Ω
50 Ω
VG2
CL
(see Note A)
RL
TEST
VDD
S1
RL
VI
CL
V∆
tPLZ/tPZL
3.3 V ± 0.3 V
2 × VDD
200 Ω
GND
10 pF
0.3 V
tPHZ/tPZH
3.3 V ± 0.3 V
GND
200 Ω
VDD
10 pF
0.3 V
Output Control
(VIN)
2.5 V
1.25 V
Output
Waveform 1
S1 at 2 y VDD tPZL
(see Note B)
0V
tPLZ
VOH
VDD/2
tPZH
Output
Waveform 2
S1 at GND
(see Note B)
1.25 V
VOL +0.3 V
VOL
tPHZ
VDD/2
VOH −0.3 V
VOH
VOL
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
Figure 4. Test Circuit and Voltage Waveforms
Submit Documentation Feedback
9
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
PARAMETER MEASUREMENT INFORMATION
(Skew)
VDD
Input Generator
VIN
50 Ω
50 Ω
VG1
TEST CIRCUIT
DUT
2 × VDD
Input Generator
RL
VO
VI
S1
Open
GND
50 Ω
50 Ω
VG2
CL
(see Note A)
RL
TEST
VDD
S1
RL
VI
CL
tsk(o)
3.3 V ± 0.3 V
Open
200 Ω
VDD or GND
10 pF
tsk(p)
3.3 V ± 0.3 V
Open
200 Ω
VDD or GND
10 pF
V∆
3.5 V
2.5 V
1.5 V
Data In at
Ax or Ay
tPLHx
tPHLx
VOH
(VOH + VOL)/2
VOL
Data Out at
XB1 or XB2
tsk(o)
3.5 V
tsk(o)
tPLH
VOH
(VOH + VOL)/2
VOL
Data Out at
YB1 or YB2
tPLHy
2.5 V
1.5 V
Input
tPHLy
tPHL
VOH
(VOH + VOL)/2
VOL
Output
tsk(p) = |tPHL − tPLH|
tsk(o) = |tPLHy − tPLHx| or |tPHLy − tPHLx|
VOLTAGE WAVEFORMS
OUTPUT SKEW (tsk(o))
VOLTAGE WAVEFORMS
PULSE SKEW (tsk(p))
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
D. The outputs are measured one at a time, with one transition per measurement.
Figure 5. Test Circuit and Voltage Waveforms
10
Submit Documentation Feedback
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
VBIAS
Network Analyzer
(HP8753ES)
P1
P2
VDD
A0
SEL
0B1
DUT
CL = 10 pF
(see Note A)
VSEL
NOTE A: CL includes probe and jig capacitance.
Figure 6. Test Circuit for Frequency Response (BW)
Frequency response is measured at the output of the ON channel. For example, when VSEL = 0 and A0 is the
input, the output is measured at 0B1. All unused analog I/O ports are left open.
HP8753ES Setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
Submit Documentation Feedback
11
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
VBIAS
Network Analyzer
(HP8753ES)
P1
P2
VDD
A0
0B1
RL = 100 Ω
A1
1B1
0B2
DUT
A2
1B2
2B1
RL = 100 Ω
A3
3B1
2B2
3B2
SEL
VSEL
NOTES: A. CL includes probe and jig capacitance.
B. A 50-Ω termination resistor is needed to match the loading of the network analyzer.
Figure 7. Test Circuit for Crosstalk (XTALK)
Crosstalk is measured at the output of the nonadjacent ON channel. For example, when VSEL = 0 and A1 is the
input, the output is measured at A3. All unused analog input (A) ports are connected to GND, and output (B)
ports are left open.
HP8753ES Setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
12
Submit Documentation Feedback
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
www.ti.com
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
VBIAS
Network Analyzer
(HP8753ES)
P1
P2
VDD
A0
0B1
RL = 100 Ω
A1
1B1
DUT
0B2
1B2
SEL
VSEL
NOTES: A. CL includes probe and jig capacitance.
B. A 50-Ω termination resistor is needed to match the loading of the network analyzer.
Figure 8. Test Circuit for OFF Isolation (OIRR)
OFF isolation is measured at the output of the OFF channel. For example, when VSEL = GND and A1 is the
input, the output is measured at 1B2. All unused analog input (A) ports are connected to ground, and output (B)
ports are left open.
HP8753ES Setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
Submit Documentation Feedback
13
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TS3DV416DGGR
ACTIVE
TSSOP
DGG
48
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
TS3DV416
TS3DV416DGVR
ACTIVE
TVSOP
DGV
48
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
SD416
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of