Sample &
Buy
Product
Folder
Technical
Documents
Support &
Community
Tools &
Software
TS3USB221A
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
TS3USB221A ESD Protected, High-Speed USB 2.0 (480-Mbps) 1:2 Multiplexer and
Demultiplexer Switch With Single Enable
1 Features
3 Description
•
•
•
•
•
•
•
•
•
•
The TS3USB221A device is a high-bandwidth switch
specially designed for the switching of high-speed
USB 2.0 signals in handset and consumer
applications, such as cell phones, digital cameras,
and notebooks with hubs or controllers with limited
USB I/Os. The wide bandwidth (900 MHz) of this
switch allows signals to pass with minimum edge and
phase distortion. The device multiplexes differential
outputs from a USB host device to one of two
corresponding outputs. The switch is bidirectional and
offers little or no attenuation of the high-speed signals
at the outputs. The device also has a low power
mode that will reduce the power consumtion to 1 μA
for portible applications with a battery or limited
power budget. The device is designed for low bit-tobit skew and high channel-to-channel noise isolation,
and is compatible with various standards, such as
high-speed USB 2.0 (480 Mbps).
1
•
•
VCC Operation at 2.5 V to 3.3 V
VI/O Accepts Signals Up to 5.5 V
1.8-V Compatible Control-Pin Inputs
Low-Power Mode When OE Is Disabled (1 μA)
RON = 6 Ω Maximum
ΔRON = 0.2 Ω Typical
Cio(on) = 6 pF Typical
Low Power Consumption (30 μA Maximum)
High Bandwidth (900 MHz Typical)
Latch-Up Performance Exceeds 100 mA
Per JESD 78, Class II
ESD Performance Tested Per JESD 22
– 7000-V Human-Body Model
(A114-B, Class II)
– 1000-V Charged-Device Model (C101)
ESD Performance I/O to GND
– 12-kV Human-Body Model
The TS3USB221A device integrates ESD protection
cells on all pins, is available in a tiny μQFN package
(2 mm × 1.5 mm) and is characterized over the free
air temperature range from –40°C to 85°C.
2 Applications
•
•
•
•
•
Routes Signals for USB 1.0, 1.1, and 2.0
Mobile Phones
Cameras
Notebooks
USB I/O expansion
Device Information(1)
PART NUMBER
TS3USB221A
PACKAGE
UQFN
BODY SIZE (NOM)
1.50 mm × 2.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
4 Simplified Schematic
D+
1D+
D−
1D−
2D+
2D−
S
OE
EN is the internal enable signal applied to the switch.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TS3USB221A
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Schematic.............................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
4
7.1
7.2
7.3
7.4
7.5
7.6
4
4
4
4
5
11 Power Supply Recommendations ..................... 16
12 Layout................................................................... 16
5
13 Device and Documentation Support ................. 18
Absolute Maximum Ratings .....................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics ..........................................
Dynamic Electrical Characteristics, VCC = 3.3 V
±10% ..........................................................................
7.7 Dynamic Electrical Characteristics, VCC = 2.5 V
±10% ..........................................................................
7.8 Switching Characteristics, VCC = 3.3 V ±10%...........
7.9 Switching Characteristics, VCC = 2.5 V ±10%...........
7.10 Typical Characteristics ............................................
6
6
6
7
8
9
Parameter Measurement Information .................. 8
Detailed Description ............................................ 12
9.1
9.2
9.1
9.2
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
12
12
13
13
10 Application and Implementation........................ 14
10.1 Application Information.......................................... 14
10.2 Typical Application ................................................ 14
12.1 Layout Guidelines ................................................. 16
12.2 Layout Example .................................................... 17
13.1 Trademarks ........................................................... 18
13.2 Electrostatic Discharge Caution ............................ 18
13.3 Glossary ................................................................ 18
14 Mechanical, Packaging, and Orderable
Information ........................................................... 18
5 Revision History
Changes from Original (November 2008) to Revision A
Page
•
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section. ................................................................................................ 1
•
Deleted the Ordering Information table from the data sheet. See the Mechanical, Packaging, and Orderable
Information section for the ordering information..................................................................................................................... 1
•
Update the document to the new TI data sheet standard ..................................................................................................... 1
2
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
TS3USB221A
www.ti.com
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
6 Pin Configuration and Functions
10-Pin µQFN
RSE Package
(Top View)
VCC
1D+
1
1D–
10
9
S
2
8
D+
2D+
3
7
D–
2D–
4
6
OE
1
1D+
5
GND
10-Pin µQFN
RSE Package
(Bottom View)
VCC
10
S
9
D+
8
2
1D–
D–
7
3
2D+
OE
6
4
2D–
5
GND
Pin Functions
PIN
NAME
DESCRIPTION
NO.
I/O
1D+
1
I/O
1D–
2
I/O
2D+
3
I/O
2D–
4
I/O
GND
5
-
Ground
OE
6
I
Bus-switch enable
D+
8
I/O
Common USB port
D—
7
I/O
S
9
I
Select input
VCC
10
-
Supply voltage
USB port 1
USB port 2
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
3
TS3USB221A
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
Supply voltage, VCC
Control input voltage, VS, V OE
Switch I/O voltage, VI/O
(2) (3)
(2) (3) (4)
Control input clamp current, IIK
VIN < 0
I/O port clamp current, II/OK
VI/O < 0
ON-state switch current, II/O
MIN
MAX
UNIT
–0.5
4.6
V
–0.5
7
V
–0.5
7
V
–50
mA
(5)
Continuous current through VCC or GND
Tstg
(1)
(2)
(3)
(4)
(5)
Storage temperature range
–65
–50
mA
±120
mA
±100
mA
150
°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to ground, unless otherwise specified.
The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
VI and VO are used to denote specific conditions for VI/O.
II and IO are used to denote specific conditions for II/O.
7.2 ESD Ratings
VALUE
Human-body model (HBM), per
ANSI/ESDA/JEDEC JS-001 (1)
V(ESD)
Electrostatic discharge
All pins except I/O to
GND
±7000
I/O to GND
±12000
Charged-device model (CDM), per JEDEC
All pins
specification JESD22-C101 (2)
(1)
(2)
UNIT
V
±1000
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 500-V HBM is possible with the necessary precautions.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 250-V CDM is possible with the necessary precautions.
7.3 Recommended Operating Conditions
VCC
MIN
MAX
2.3
3.6
VCC = 2.3 V to 2.7 V
0.46 × VCC
VCC
VCC = 2.7 V to 3.6 V
0.46 × VCC
VCC
VCC = 2.3 V to 2.7 V
0
0.25 × VCC
VCC = 2.7 V to 3.6 V
0
0.25 × VCC
0
5.5
V
–40
85
°C
Supply voltage
High-level control input voltage
VS, V OE
Low-level control input voltage
VI/O
Data input/output voltage
TA
Operating free-air temperature
UNIT
V
V
V
7.4 Thermal Information
THERMAL METRIC (1)
RSE
10 PINS
RθJA
Junction-to-ambient thermal resistance
179.7
RθJC(top)
Junction-to-case (top) thermal resistance
107.9
RθJB
Junction-to-board thermal resistance
100.7
ψJT
Junction-to-top characterization parameter
ψJB
Junction-to-board characterization parameter
(1)
4
UNIT
°C/W
7.1
100.0
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
TS3USB221A
www.ti.com
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
7.5 Electrical Characteristics (1)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP (2)
MAX
UNIT
–1.8
V
VIK
Input-Source Clamp Voltage
VCC = 3.6 V, 2.7 V, II = –18 mA
IIN
Input leakage current, control
inputs
VCC = 3.6 V, 2.7 V, 0 V, VIN = 0 V to 3.6 V
±1
μA
Off-state leakage current
VCC = 3.6 V, 2.7 V, VO = 0 V to 5.25 V, VI = 0 V,
VIN = VCC or GND, Switch OFF
±1
μA
Power-off leakage current
VCC = 0 V
ICC
Supply Current
VCC = 3.6 V, 2.7 V, VIN = VCC or GND,
II/O = 0 V, Switch ON or OFF
30
μA
ICC
Supply Current (low power
mode)
VCC = 3.6 V, 2.7 V, VIN = VCC or GND,
Switch disabled, OE in high state
1
μA
Supply-current change, control
inputs
One input at 1.8 V,
Other inputs at VCC
or GND
Cin
Input capacitance, control
inputs
VCC = 3.3 V, 2.5 V, VIN = VCC or 0 V
1.5
2.5
pF
Cio(OFF)
OFF capacitance
VCC = 3.3 V, 2.5 V, VI/O = VCC or 0 V, Switch OFF
3.5
5
pF
Cio(ON)
ON capacitance
VCC = 3.3 V, 2.5 V, VI/O = VCC or 0 V, Switch ON
6
7.5
pF
3
6
VI = 2.4 V, IO = –15 mA
3.4
6
VI = 0 V, IO = 30 mA
0.2
VI = 1.7, IO = –15 mA
0.2
IOZ
(3)
I(OFF)
ΔICC
(4)
(5)
RON
ON-state resistance
VCC = 3 V, 2.3 V
ΔRON
ON-state resistance match
between channels
VCC = 3 V, 2.3 V
RON(flat)
ON-state resistance flatness
VCC = 3 V, 2.3 V
(1)
(2)
(3)
(4)
(5)
VI/O = 0 V to 5.25 V
±2
VI/O = 0 V to 3.6 V
±2
VI/O = 0 V to 2.7 V
±1
VCC = 3.6 V
20
VCC = 2.7 V
0.5
VI = 0 V, IO = 30 mA
VI = 0 V, IO = 30 mA
1
VI = 1.7, IO = –15 mA
1
μA
μA
Ω
Ω
Ω
VIN and IIN refer to control inputs. VI, VO, II, and IO refer to data pins.
All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.
For I/O ports, the parameter IOZ includes the input leakage current.
This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND.
Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is
determined by the lower of the voltages of the two (A or B) terminals.
7.6 Dynamic Electrical Characteristics, VCC = 3.3 V ±10%
over operating range, TA = –40°C to 85°C, VCC = 3.3 V ±10%, GND = 0 V
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
XTALK
Crosstalk
RL = 50 , f = 250 MHz
–40
OIRR
OFF isolation
RL = 50 , f = 250 MHz
–41
dB
BW
Bandwidth (–3 dB)
RL = 50
0.9
GHz
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
dB
5
TS3USB221A
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
www.ti.com
7.7 Dynamic Electrical Characteristics, VCC = 2.5 V ±10%
over operating range, TA = –40°C to 85°C, VCC = 2.5 V ±10%, GND = 0 V
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
XTALK
Crosstalk
RL = 50 , f = 250 MHz
–39
OIRR
OFF isolation
RL = 50 , f = 250 MHz
-40
dB
dB
BW
Bandwidth (3 dB)
RL = 50
0.9
GHz
7.8 Switching Characteristics, VCC = 3.3 V ±10%
over operating range, TA = –40°C to 85°C, VCC = 3.3 V ±10%, GND = 0 V
PARAMETER
tpd
Propagation delay
MIN
(2) (3)
Line enable time
tOFF
Line disable time
tSK(O)
Output skew between center port to any other port (2)
(1)
(2)
(3)
MAX
0.25
tON
tSK(P)
TYP (1)
ns
S to D, nD
30
OE to D, nD
17
S to D, nD
12
OE to D, nD
10
Skew between opposite transitions of the same output (tPHL– tPLH)
(2)
UNIT
ns
ns
0.1
0.2
ns
0.1
0.2
ns
For Max or Min conditions, use the appropriate value specified under Electrical Characteristics for the applicable device type.
Specified by design
The bus switch contributes no propagational delay other than the RC delay of the on resistance of the switch and the load capacitance.
The time constant for the switch alone is of the order of 0.25 ns for 10-pF load. Since this time constant is much smaller than the rise/fall
times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch, when used in
a system, is determined by the driving circuit on the driving side of the switch and its interactions with the load on the driven side.
7.9 Switching Characteristics, VCC = 2.5 V ±10%
over operating range, TA = –40°C to 85°C, VCC = 2.5 V ±10%, GND = 0 V
PARAMETER
tpd
Propagation delay
MIN
(2) (3)
TYP (1)
MAX
0.25
UNIT
ns
S to D, nD
50
OE to D, nD
32
S to D, nD
23
OE to D, nD
12
tON
Line enable time
tOFF
Line disable time
tSK(O)
Output skew between center port to any other port (2)
0.1
0.2
ns
tSK(P)
Skew between opposite transitions of the same output (tPHL– tPLH) (2)
0.1
0.2
ns
(1)
(2)
(3)
6
ns
ns
For Max or Min conditions, use the appropriate value specified under Electrical Characteristics for the applicable device type.
Specified by design
The bus switch contributes no propagational delay other than the RC delay of the on resistance of the switch and the load capacitance.
The time constant for the switch alone is of the order of 0.25 ns for 10-pF load. Since this time constant is much smaller than the rise/fall
times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch, when used in
a system, is determined by the driving circuit on the driving side of the switch and its interactions with the load on the driven side.
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
TS3USB221A
www.ti.com
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
7.10 Typical Characteristics
0
0
–1
–20
Attenuation (dB)
Gain (dB)
–2
–3
–4
–40
–60
–80
–5
–100
–6
–120
–7
100.0E+3
100.0E+3
1.0E+6
10.0E+6
100.0E+6
1.0E+9
1.0E+6
100.0E+6
1.0E+9
10.0E+9
Frequency (Hz)
Frequency (Hz)
Figure 2. OFF Isolation vs Frequency
Figure 1. Gain vs Frequency
0
3.5
–20
3.4
3.3
–40
VCC = 3 V
ron (Ω)
Attenuation (dB)
10.0E+6
10.0E+9
–60
3.2
VCC = 2.3 V
3.1
–80
3.0
–100
2.9
–120
100.0E+3
2.8
1.0E+6
10.0E+6
100.0E+6
1.0E+9
10.0E+9
0.0
0.5
1.0
1.5
3.0
3.5
Submit Documentation Feedback
7
Frequency (Hz)
2.0
2.5
VIN (V)
Figure 3. Crosstalk vs Frequency
Figure 4. ron vs VIN (IOUT = –15 mA)
3.5
3.4
3.3
ron (Ω)
VCC = 3 V
3.2
VCC = 2.3 V
3.1
3.0
2.9
2.8
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VIN (V)
Figure 5. rON vs VIN (IOUT = 30 mA)
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
TS3USB221A
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
www.ti.com
8 Parameter Measurement Information
VCC
1D or 2D VOUT1 or VOUT2
VIN
RL
CL
VCOM
tON
500 Ω
50 pF
V+
tOFF
500 Ω
50 pF
V+
D
CL(2)
1D or 2D
VCTRL
TEST
RL
S
CL(2)
Logic
Input(1)
RL
GND
1.8 V
Logic
Input
(VI)
50%
50%
0
tON
tOFF
Switch
Output
(VOUT1 or VOUT2)
(1)
(2)
90%
90%
VOH
VOL
All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns.
CL includes probe and jig capacitance.
Figure 6. Turn-On (tON) and Turn-Off Time (tOFF)
VCC
Network Analyzer
Channel OFF: 1D to D
50 W
VOUT1 1D
VCTRL = VCC or GND
D
Source
Signal
50 W
VIN
2D
Network Analyzer Setup
Source Power = 0 dBm
(632-mV P-P at 50-W load)
VCTRL S
50 W
+
GND
DC Bias = 350 mV
Figure 7. OFF Isolation (OISO)
8
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
TS3USB221A
www.ti.com
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
Parameter Measurement Information (continued)
VCC
Network Analyzer
Channel ON: 1D to D
50 W
VOUT1 1D
Channel OFF: 2D to D
VIN
Source
Signal
VCTRL = VCC or GND
VOUT2 2D
50 W
Network Analyzer Setup
50 W
VCTRL S
+
Source Power = 0 dBm
(632-mV P-P at 50-W load)
GND
DC Bias = 350 mV
Figure 8. Crosstalk (XTALK)
VCC
Network Analyzer
50 W
VOUT1
1D
Channel ON: 1D to D
D
Source
Signal
VIN
VCTRL = VCC or GND
2D
Network Analyzer Setup
50 W
VCTRL
+
Source Power = 0 dBm
(632-mV P-P at 50-W load)
S
GND
DC Bias = 350 mV
Figure 9. Bandwidth (BW)
400 mV
Figure 10. Propagation Delay
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
9
TS3USB221A
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
www.ti.com
Parameter Measurement Information (continued)
800 mV
50%
50%
Input
400 mV
tPLH
tPHL
VOH
50%
Output
VOL
tSK(P) = | tPHL – tPLH |
PULSE SKEW tSK(P)
800 mV
50%
50%
Input
400 mV
tPLH1
tPHL1
VOH
50%
50%
Output 1
VOL
tSK(O)
tSK(O)
VOH
50%
50%
Output 2
tPLH2
VOL
tPHL2
tSK(O) = | tPLH1 – tPLH2 | or | tPHL1 – tPHL2 |
OUTPUT SKEW tSK(P)
Figure 11. Skew Test
VCC
VOUT1 1D
+
D
VIN
Channel ON
VOUT2 2D
r on +
VCTRL
IIN
S
VIN * VOUT2 or VOUT1
W
IIN
VCTRL = VIH or VIL
+
GND
Figure 12. ON-State Resistance (ron)
10
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
TS3USB221A
www.ti.com
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
Parameter Measurement Information (continued)
VCC
VOUT1 1D
VIN
D
+
VOUT2 2D
VCTRL
+
S
OFF-State Leakage Current
Channel OFF
VCTRL = VIH or VIL
+
GND
Figure 13. OFF-State Leakage Current
VCC
VOUT1 1D
Capacitance
Meter
VBIAS
VBIAS = VCC or GND
VOUT2 2D
VCTRL = VCC or GND
VIN D
Capacitance is measured at 1D,
2D, D, and S inputs during ON
and OFF conditions.
VCTRL S
GND
Figure 14. Capacitance
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
11
TS3USB221A
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
www.ti.com
9 Detailed Description
9.1 Overview
The TS3USB221A device is a 2-channel SPDT switch specially designed for the switching of high-speed USB
2.0 signals in handset and consumer applications, such as cell phones, digital cameras, and notebooks with
hubs or controllers with limited USB I/Os. The wide bandwidth (900 MHz) of this switch allows signals to pass
with minimum edge and phase distortion. The device multiplexes differential outputs from a USB host device to
one of two corresponding outputs. The switch is bidirectional and offers little or no attenuation of the high-speed
signals at the outputs. The device also has a low power mode that will reduce the power consumption to 1 μA for
portible applications with a battery or limited power budget.
The device is designed for low bit-to-bit skew and high channel-to-channel noise isolation, and is compatible with
various standards, such as high-speed USB 2.0 (480 Mbps).
The TS3USB221A device integrates ESD protection cells on all pins, is available in a tiny μQFN package (2 mm
× 1.5 mm) and is characterized over the free air temperature range from –40°C to 85°C.
9.2 Functional Block Diagram
D+
1D+
D−
1D−
2D+
2D−
S
OE
A
B
VCC
Charge
Pump
EN (see Note A)
A.
EN is the internal enable signal applied to the switch.
Figure 15. Simplified Schematic of Each FET Switch (SW)
12
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
TS3USB221A
www.ti.com
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
9.1 Feature Description
9.1.1 Low Power Mode
The TS3USB221A has a low power mode that reduces the power consumption to 1 μA while the devices is not
in use. To put the device in low power mode and disable the switch, the bus-switch enable pin OE must be
supplied with a logic "High" signal.
9.2 Device Functional Modes
Table 1. Truth Table
S
OE
FUNCTION
X
H
Disconnect
L
L
D = 1D
H
L
D = 2D
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
13
TS3USB221A
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
www.ti.com
10 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
There are many USB applications in which the USB hubs or controllers have a limited number of USB I/Os. The
TS3USB221A solution can effectively expand the limited USB I/Os by switching between multiple USB buses in
order to interface them to a single USB hub or controller.
10.2 Typical Application
3.3 V
0.1 μF
0.1 μF
VCC
System
Controller
Switch
Control Logic
USB
Controller
TS3USB221A
2-channel
SPDT
S
OE
1D+
1DD+
USB Port 1
D2D+
2D-
USB Port 2
GND
Figure 16. Application Schematic
14
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
TS3USB221A
www.ti.com
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
Typical Application (continued)
10.2.1 Design Requirements
Design requirements of the USB 1.0,1.1, and 2.0 standards should be followed.
It is recommended that the digital control pins S and OE be pulled up to VCC or down to GND to avoid undesired
switch positions that could result from the floating pin.
10.2.2 Detailed Design Procedure
The TS3USB221A can be properly operated without any external components. However, it is recommended that
unused pins should be connected to ground through a 50-Ω resistor to prevent signal reflections back into the
device.
0.5
0.5
0.4
0.4
0.3
0.3
Differential Signal (V)
Differential Signal (V)
10.2.3 Application Curves
0.2
0.1
0.0
–0.1
–0.2
0.2
0.1
0.0
–0.1
–0.2
–0.3
–0.3
–0.4
–0.4
–0.5
–0.5
0.0
0.2
0.4
0.5
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0.0
0.2
0.4
0.5
–9
0.8
1.0
1.2
1.4
1.6
1.8
2.0
–9
Time (X 10 ) (s)
Time (X 10 ) (s)
Figure 17. Eye Pattern: 480-Mbps USB Signal With No
Switch (Through Path)
Figure 18. Eye Pattern: 480-Mbps USB Signal With Switch
NC Path
0.5
0.4
Differential Signal (V)
0.3
0.2
0.1
0.0
–0.1
–0.2
–0.3
–0.4
–0.5
0.0
0.2
0.4
0.5
0.8
1.0
1.2
1.4
1.6
1.8
2.0
–9
Time (X 10 ) (s)
Figure 19. Eye Pattern: 480-Mbps USB Signal With Switch NO Path
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
15
TS3USB221A
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
www.ti.com
11 Power Supply Recommendations
Power to the device is supplied through the VCC pin and should follow the USB 1.0, 1.1, and 2.0 standards. A
bypass capacitor is recommended to be placed as close to the supply pin VCC to help smooth out lower
frequency noise to provide better load regulation across the frequency spectrum.
12 Layout
12.1 Layout Guidelines
Place supply bypass capacitors as close to VCC pin as possible and avoid placing the bypass caps near the
D+/D- traces.
The high speed D+/D- traces should always be matched lengths and must be no more than 4 inches; otherwise,
the eye diagram performance may be degraded. A high-speed USB connection is made through a shielded,
twisted pair cable with a differential characteristic impedance. In layout, the impedance of D+ and D- traces
should match the cable characteristic differential impedance for optimal performance.
Route the high-speed USB signals using a minimum of vias and corners which will reduce signal reflections and
impedance changes. When a via must be used, increase the clearance size around it to minimize its
capacitance. Each via introduces discontinuities in the signal’s transmission line and increases the chance of
picking up interference from the other layers of the board. Be careful when designing test points on twisted pair
lines; through-hole pins are not recommended.
When it becomes necessary to turn 90°, use two 45° turns or an arc instead of making a single 90° turn. This
reduces reflections on the signal traces by minimizing impedance discontinuities.
Do not route USB traces under or near crystals, oscillators, clock signal generators, switching regulators,
mounting holes, magnetic devices or IC’s that use or duplicate clock signals.
Avoid stubs on the high-speed USB signals because they cause signal reflections. If a stub is unavoidable, then
the stub should be less than 200 mm.
Route all high-speed USB signal traces over continuous planes (VCC or GND), with no interruptions.
Avoid crossing over anti-etch, commonly found with plane splits.
Due to high frequencies associated with the USB, a printed circuit board with at least four layers is
recommended; two signal layers separated by a ground and power layer as shown in Figure 20.
Signal 1
GND Plane
Power Plane
Signal 2
Figure 20. Four-Layer Board Stack-Up
The majority of signal traces should run on a single layer, preferably Signal 1. Immediately next to this layer
should be the GND plane, which is solid with no cuts. Avoid running signal traces across a split in the ground or
power plane. When running across split planes is unavoidable, sufficient decoupling must be used. Minimizing
the number of signal vias reduces EMI by reducing inductance at high frequencies.
16
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
TS3USB221A
www.ti.com
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
12.2 Layout Example
LEGEND
VIA to Power Plane
Polygonal Copper Pour
VIA to GND Plane
Bypass Capacitor
V+
To Microcontroller
10
1 1D+
VCC
S
9
2 1D-
D+
8
3 2D+
D-
7
USB Port 1
To USB Host
USB Port 2
4 2D-
OE 6
GND
5
To Microcontroller
Figure 21. Package Layout Diagram
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
17
TS3USB221A
SCDS277A – NOVEMBER 2008 – REVISED FEBRUARY 2015
www.ti.com
13 Device and Documentation Support
13.1 Trademarks
All trademarks are the property of their respective owners.
13.2 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
13.3 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
18
Submit Documentation Feedback
Copyright © 2008–2015, Texas Instruments Incorporated
Product Folder Links: TS3USB221A
PACKAGE OPTION ADDENDUM
www.ti.com
25-Oct-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
TS3USB221ARSER
ACTIVE
UQFN
RSE
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU |
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
(LH7 ~ LHR ~ LHV)
TS3USB221ARSERG4
ACTIVE
UQFN
RSE
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
(LH7 ~ LHR ~ LHV)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Oct-2016
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TS3USB221A :
• Automotive: TS3USB221A-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Aug-2017
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
2.3
0.75
4.0
8.0
Q1
TS3USB221ARSER
UQFN
RSE
10
3000
180.0
9.5
TS3USB221ARSER
UQFN
RSE
10
3000
180.0
9.5
1.7
2.2
0.75
4.0
8.0
Q1
TS3USB221ARSER
UQFN
RSE
10
3000
180.0
8.4
1.68
2.13
0.76
4.0
8.0
Q1
Pack Materials-Page 1
1.7
B0
(mm)
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Aug-2017
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TS3USB221ARSER
UQFN
RSE
10
3000
184.0
184.0
19.0
TS3USB221ARSER
UQFN
RSE
10
3000
189.0
185.0
36.0
TS3USB221ARSER
UQFN
RSE
10
3000
202.0
201.0
28.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
