TSC2013EVM

User's Guide SLVUA92 – July 2014 TSC2013EVM User's Guide 1 Introduction This user's guide describes the characteristics, operation, and use of the TSC2013 evaluation module (EVM). This EVM, featuring the TSC2013 resistive dual-touch controller, is a fully-functional USB-powered platform that allows 4-wire resistive touch-screen panels to be connected to the USB port of a PC or laptop for evaluation. A complete circuit description, schematic diagram, and bill of materials are included in this document. The following related documents are available through the Texas Instruments web site at www.ti.com. The following lists devices and corresponding device data sheets of devices that are compatible with this EVM: • TSC2013, SLVSC89 • DRV2605, SLOS825 • REG1117-33, SBVS001 • MSP430F247, SLAS547I 2 EVM Overview 2.1 Features The TSC2013EVM is a complete evaluation and demonstration kit that includes a USB-based board and evaluation software for use with a personal computer running Microsoft Windows® operating systems (OS). 3 Analog Interface The TSC2013EVM is designed for easy interfacing to 4-wire resistive touch screen panels. Table 1. Analog Interface Pinout PIN NUMBER SIGNAL DESCRIPTION J300.1 Y– Touch screen Y- electrode J300.2 X– Touch screen X- electrode J300.3 Y+ Touch screen Y+ electrode J300.4 X+ Touch screen X+ electrode SLVUA92 – July 2014 Submit Documentation Feedback TSC2013EVM User's Guide Copyright © 2014, Texas Instruments Incorporated 1 Digital Interface 4 www.ti.com Digital Interface The TSC2013EVM is designed to easily interface with multiple control platforms. Table 2. Digital Interface Pinout 5 PIN NUMBER SIGNAL J202.1 GND DESCRIPTION J202.2 RST Hardware reset input J202.3 SDA_A Serial data I/O J202.4 SCL_A Serial clock J202.5 INT_TSC Interrupt output (for host systems) J202.6 GND J201.1 RXD_Debug J201.2 GND J201.3 TXD_Debug Receiving asynchronous data input. For debug purpose. Transmit Asynchronous Data Output. For debug purpose. Power Supplies The USB connection supplies the TSC2013EVM with power. Onboard regulators generate the required supply voltages and no further power supplies are necessary. The power-supply voltage has an LED (LED502) that lights up when the power supplies are active. 6 EVM Operation The following section provides information on the analog input, digital control, and general operating conditions of the TSC2013EVM. 6.1 Analog Input The analog input sources (touch screen) can be applied directly to pin J300. 6.2 Digital Control The digital control signals are applied through the USB connection and no other connections are required. The TSC2013EVM can also be connected to a DSP or microcontroller interface board through the J202 pin. If external I2C control is desired, remove the following resisters: R231, R232, and R233. 2 TSC2013EVM User's Guide SLVUA92 – July 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated Kit Operation www.ti.com 7 Kit Operation The following section provides information on using the TSC2013EVM, including setup, program installation, and program usage. 7.1 TSC2013EVM-PDK Block Diagram Figure 1 shows a block diagram of the TSC2013EVM. The TSC2013 and DRV2605 device are both controlled by an MSP430™ microcontroller (MCU) through an I2C interface. One resistive touch panel is connected to the TSC2013 device by a 4-pin FPC connector and an LRA motor is attached as an actuator. The FT232 device is a USB-to-serial UART interface and is used to transfer data from the MSP430 MCU to the host PC or is used to receive commands from the host PC. USB FT232 MSP430 2 2 I C I C TSC2013 DRV2605 Resistive Touch Panel LRA Motor Figure 1. TSC2013EVM Block Diagram SLVUA92 – July 2014 Submit Documentation Feedback TSC2013EVM User's Guide Copyright © 2014, Texas Instruments Incorporated 3 Kit Operation 7.2 www.ti.com Quick Start Place the CD-ROM into CD-ROM drive of the PC. Locate the Setup.exe program on the disk and execute the program. The setup program installs the TSC2013 evaluation software on the PC. Follow the instructions and prompts given to correctly install the software. After the software is installed, a dialog box appears with instructions for installing the FTDI CDM drivers which are a self-extracting archive. Click the Extract button to proceed. The archive extracts the files and automatically runs the installer for the FTDI CDM Drivers which is shown in Figure 2. When the driver installation is complete, attach a USB cable from the PC to the TSC2013EVM board. The board receives power from the USB interface and therefore the power-indicator LED (LED502) on the TSC2013EVM should light up when the USB cable is attached. When the USB cable is connected to the PC and the EVM board, launch the TSC2013 evaluation software on the PC. A screen similar to the one in Figure 4 should appear when the software is launched. Figure 2. FTDI CMD Drivers Installer Screen Figure 3. Serial Settings Screen 4 TSC2013EVM User's Guide SLVUA92 – July 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated Kit Operation www.ti.com Figure 4. Default Software Screen In order to use the touch-screen features, a 4-wire resistive-touch screen must be connected to the J300 pin of the TSC2013EVM, as previously described. Click the Serial Settings button and the window shown in Figure 3 opens. Select the correct port and click the OK button. Click the Connect button and the word Connected appears with a green background in the bottom left of the screen. Figure 4 shows the word Disconnected with a red background. If the port number is unknown, navigate to the PC Device Manager from the Control Panel that is located on the Start Menu of a PC running a Windows OS. Expand the Ports (COM & LPT) list to view the ports. Select the port that has an annotation beginning with USB Serial Port as shown in Figure 5. Figure 5. Device Manager Screen SLVUA92 – July 2014 Submit Documentation Feedback TSC2013EVM User's Guide Copyright © 2014, Texas Instruments Incorporated 5 Kit Operation 7.3 www.ti.com Program Description After the TSC2013EVM software is installed, the EVM board can be used to evaluate and develop the TSC2013 device. 7.3.1 1-Finger Trace Panel The touch-screen box in the 1-Finger Trace Panel is updated when a touch is detected on the touch screen (see Figure 6). When the touch screen is drawn on, the drawing motion on the touch screen is translated into pixels on this box. The display can be cleared by pressing the Clear button on the screen. Figure 6. 1-Finger Trace Screen 7.3.2 2-Finger Gesture Panel The TSC2013EVM supports three types of gestures which are zoom in or out, rotation, and 1-finger flick. Pictures are updated when a gesture is detected by the firmware in the MSP430 device (see Figure 7). For example, if a user performs a zoom in or zoom out gesture on the touch panel, the picture on the screen zooms in or out at the same time that the gesture is performed. Figure 7. 2-Finger Gesture Screen 6 TSC2013EVM User's Guide SLVUA92 – July 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated EVM Bill of Materials (BOM) and Schematic www.ti.com 8 EVM Bill of Materials (BOM) and Schematic Table 3 lists the complete BOM for the modular TSC2013EVM. Table 3. TSC2013EVM Bill of Materials DESIGNATORS DESCRIPTION MANUFACTURER PART NUMBER C100, C101, C102, C103, C104, C300, C303, C501 10-µF, capacitor,10%,SMT0805 AVX 0805YD106KAT2A C200, C202 1-µF, capacitor,10%,SMT0603 KEMET C0603C102K3GACTU C201 1-nF, capacitor,10%,SMT0603 TDK C0603X5R1E102K030BA C203, C503 10-nF, capacitor,SMT0603 KEMET C0603C103K4RACTU C204, C205 12-pF, capacitor,5%,SMT0603 TDK C0603C0G1E120J030BA C301, C302, C305, C404, C405, C500, C502, C504 100-nF, capacitor,10%,SMT0603 AVX 06033C104KAT2A FB200, FB500 Ferrite bead, 100-Ω at 100 MHz,SMT0805 Fair-Rite 2508051017Y0 F500 Fuse, 0.5-A, SMT0805 Multicomp MCF0805B0R50FSTR J200 Connector, header, 2 rows, 14-pin TE Connectivity / AMP 1-1634688-4 J201 Connector, header, right angle, single row, 3-pin TE Connectivity / AMP 826947-3 J202 Connector, header, right angle, single row, 6-pin TE Connectivity / AMP 826949-6 J300 Receptacle FPC, 1-MM Molex 52271-0479 J400 LRA Motor AAC AAC1030 J500 Mini-USB type-B receptacle Würth Elektronik 65100516121 LED500, LED501, LED502 LED, Green, SMT0805 Würth Elektronik 150080GS75000 R231, R232, R233, R300, R405, R407 Resistor, 0, 5%, 0.1-W, SMT0603 Panasonic ERJ-3GEY0R00V R200 Resistor, 47-kΩ,5%, 0.1-W, SMT0603 Panasonic ERJ3GEYJ473V R201, R202, R207, R208, R222, R223 Resistor, 4.7-kΩ, 5%, 0.1-W, SMT0603 Panasonic ERJ3GEYJ472V R203, R204, R205, R206, R209, R212, R213, R214, R224, R302, R303, R308, R408, R505 Resistor, 100-Ω, 5%, 0.1-W, SMT0603 Panasonic ERJ3GEYJ101V R228, R229, R230, R404, R406 Resistor, 10-kΩ, 5%, 0.1-W, SMT0603 Panasonic ERJ3GEYJ103V R309 Resistor, 47-Ω, 5%, 0.1-W, SMT0603 Panasonic ERJ3GEYJ470V R500, R501, R502 Resistor, 22-Ω, 5%, 0.1-W, SMT0603 Panasonic ERJ3GEYJ220V R503, R504, R506 Resistor, 1-kΩ, 5%, 0.1-W, SMT0603 Panasonic ERJ3GEYJ102V SW200 DIP switch OMRON A6S-3104-H U100, U101 Single output LDO, 800-mA, fixed (3.3-V) Texas Instruments REG1117-3.3 U200 16-bit MCU, 32-KB Flash, 4-KB RAM Texas Instruments MSP430F247TPMR U300 Resistive dual-touch controller Texas Instruments TSC2013QPWRQ1 U401 Haptic driver for ERM-LRA Texas Instruments DRV2605YZFR U500 USB to serial UART FTDI Chip FT232RL Y200 Crystal, 11.0592-MHz, SMD TXC CORPORATION 9C-11.0592MAAJ-T — LCD touch panel Fujitsu T010-1301-T320 SLVUA92 – July 2014 Submit Documentation Feedback TSC2013EVM User's Guide Copyright © 2014, Texas Instruments Incorporated 7 TSC2013EVM Schematics 9 www.ti.com TSC2013EVM Schematics The schematic diagrams are provided for reference. Power 3V3_A 3V3_D 5V -> 3V3 Vbus Power DRV2605_2603 3V3_A TSC2013 SCL_B SDA_B PWM_DRV260x TSC2013 DRV_EN SCL_A SDA_B DRV260x PWM DRV_EN SDA_A SCL_A Vbus /RST /INT_TSC SDA_A SCL_B TSC2013 DRV2605 UART2USB Vcc Vbus /RST /INT_TSC MSP430xx SCL_A SDA_A SCL_A FT232 UART -> USB SDA_A MSP430F247 SCL_B SDA_B DRV_PWM DRV_EN SCL_B SDA_B PWM_DRV260x DRV_EN RXD TXD TXD RXD /RST_UART /RST_UART MSP430xx UART2USB Figure 8. 8 TSC2013EVM User's Guide SLVUA92 – July 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated TSC2013EVM Schematics www.ti.com FB400 Vbus Vcc_DRV 100Ohm @ 100MHz C400 10uF From USB 5V C401 100nF C402 10nF Vcc_DRV C403 100nF U400 DRV2603 DRV_PWM R400 7 DRV_EN 3 OUT+ OUT- J400 Vdd DNP 9 OUT+ 1 2 PWM 6 OUTLRA/ERM 8 5 GND R402 10k GND Vcc_DRV From MSP430x GND 2 PWM EN LRA R401 4 NC DNP 10 1 DRV_EN R403 DNP Vcc_DRV 7 SCL_B 5 SDA_B R408 100 From MSP430x VDD EN OUT+ 3 IN/TRIG OUTSCL GND SDA_B 4 SDA DRV2605 VERG 9 2 R405 0 R407 0 C405 100nF 6 SCL_B U401 1 R406 10k 8 C404 100nF R404 10k Figure 9. From MiniUSB port U100 To MSP430x 4 REG1117 -3V3 3V3_D Sink 3 Vbus VIN VOUT 2 3V3_D GND 1 C101 10uF C100 10uF C102 10uF R101 DNP U101 To TSC2013 4 REG1117 -3V3 3V3_A Sink 3 VIN VOUT 2 3V3_A 1 GND C103 10uF C104 10uF Figure 10. SLVUA92 – July 2014 Submit Documentation Feedback TSC2013EVM User's Guide Copyright © 2014, Texas Instruments Incorporated 9 TSC2013EVM Schematics www.ti.com MSP430XX 4-wire JTAG port 4 5 6 Vcc_MCU H SW200 3 2 1 10k x 3 J200 L R228 R229 R230 TDO_TDI 1 2 TDI 3 4 TMS 5 6 TCK 7 8 /RST_NMI 11 12 C201 1nF 14 49 50 51 52 C200 1uF R200 47k 10 JTAG 13 53 TDI TMS TDO_TDI 54 55 TCK 56 /RST_NMI 59 60 61 62 C203 10nF 64 C202 1uF 57 100Ohm @ 100MHz 63 Vcc 58 9 FB200 Vcc_MCU P5.5_SMCLK P5.6_ACLK P5.7/TBOUTH_SVSOUT XT2IN XT2OUT TDO_TDI TDI_TCLK TMS TCK RST_NMI P6.0_A0 P6.1_A1 P6.2_A2 AVss AVcc P3.4_UCA0TXD_UCA0SIMO R203 100 SCL_B 45 R204 100 SDA_B 42 R205 100 DRV_EN 41 R206 100 DRV_PWM 40 P4.2_TB2 39 C206 38 DNP R207 4.7k R208 4.7k 37 P4.1_TB1 36 P4.0_TB0 J201 RXD_Debug 35 P3.7_UCA1RXD_UCA1SOMI R209 34 P3.6_UCA1TXD_UCA1SIMO 33 P3.5_UCA0RXD_UCA0SOMI TXD_Debug 1 2 3 100 UART 32 P3.3_UCB0CLK_UCA0STE 31 P3.2_UCB0SOMI_UCB0SCL 30 P3.0_UCB0STE_UCA0CLK P3.1_UCB0SIMO_UCB0SDA 29 28 P2.7_TA0_CA7 27 P1.4_MCLK P2.6_ADC12CLK_CA6 P1.3_TA2 26 P1.2_TA1 17 16 P1.1_TA0 P2.5_Rosc_CA5 15 P1.0_TACLK_CAOUT 25 14 P2.4_CA1_TA2 13 P4.3_TB3 Vref-_Veref- 24 12 Veref+ P2.3_CA0_TA1 11 23 10 P4.4_TB4 P2.2_CAOUT_TA0_CA4 C205 12pF XOUT 46 43 P4.7_TBCLK P4.5_TB5 To DRV260x R202 4.7k 44 P5.0_UCB1STE_UCA1CLK XIN 22 Y200 11.0592MHz P5.2_UCB1SOMI_UCB1SCL P5.1_UCB1SIMO_UCB1SDA P4.6_TB6 R201 4.7k 47 P5.3_UCB1CLK_UCA1STE MSP430F247 P2.1_TAINCLK_CA3 C204 12pF 48 P5.4_MCLK Vref+ 21 9 P6.7_A7_SVSIN P2.0_ACLK_CA2 8 U200 20 7 P6.6_A6 P1.7_TA2 6 P6.5_A5 19 5 P6.4_A4 P1.6_TA1 4 P6.3_A3 P1.5_TA0 3 Vcc_MCU DVcc 18 2 DVss Vcc_MCU 1 R214 100 V204 V205 DNP DNP RXD R215 1.5k R216 1.5k R217 1.5k R218 1.5k R219 1.5k R220 1.5k R221 1.5k TXD R224 100 R212 100 /RST_UART Vcc_MCU LED200 BLUE TouchDetected LED201 BLUE ZoomIn LED202 LED203 BLUE ZoomoOut BLUE Left LED204 LED205 BLUE Right BLUE Up LED206 To FT232RL R213 100 R222 4.7k BLUE R223 4.7k To TSC2013 Down R231 0 R232 0 R233 0 SCL_A SDA_A /RST J202 1 2 3 4 5 6 From TSC2013 /INT_TSC CON6 V200 V201 V202 V203 DNP DNP DNP DNP Figure 11. 10 TSC2013EVM User's Guide SLVUA92 – July 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated TSC2013EVM Schematics www.ti.com R300 VDD_TSC 0 3V3_A To MSP430Fx From Power /INT_TSC C303 10uF 100nF 100nF 10uF 2 SCL_A 3 16 R308 100 5 /RST 7 IOVdd 100nF INT 100 X+ XSCL Y- TSC2013 X- Y- 11 4 4 12 3 3 13 2 2 14 AUX AD1 AD0 RST Y+ 6 Y+ 6 C305 X+ SDA ThermalPad 1 AGND 100 SDA_A 4 AUX SNSGND 1 1 J300 J301 5 R303 9 SCL_A R302 INT 8 15 R309 V300 V301 V302 V303 DNP DNP DNP DNP 47 17 SDA_A DGND From MSP430Fx SNSVdd/Vref U300 6 C302 5 C301 10 C300 DNP R=Ry/4.5 Figure 12. SLVUA92 – July 2014 Submit Documentation Feedback TSC2013EVM User's Guide Copyright © 2014, Texas Instruments Incorporated 11 TSC2013EVM Schematics www.ti.com Vbus To DRV260x&Power F500 1 Vcc_FT232R C504 100nF R500 22 1 TXD 5 RXD /RST_UART 3 11 2 9 10 6 USBDM CBUS1 CBUS2 OSCO CBUS4 10uF USB_mini_B 16 R501 R502 22 2 3 22 4 TEST GND NC 23 R503 1k GREEN /TXD 13 12 GREEN /RXD D- NC NC D+ ID GND Case Case Case Case 11 10 9 8 7 6 LED500 Vcc_FT232R 22 14 Vbus J500 LED501 R504 1k 8 24 26 21 GND GND NC /RST 25 C503 10nF OSCI 7 19 C501 5 CBUS0 18 R505 100 15 FT232R AGND 28 0805 LED502 GREEN 17 USBDP CBUS3 27 100Ohm @ 100MHz 1 U500 RTS CTS DTR DSR DCD RI 2 FB500 VBUS TXD RXD 1k C502 100nF 3V3_OUT VCCIO VCC From MSP430x 4 20 C500 100nF R506 500mA Figure 13. 12 TSC2013EVM User's Guide SLVUA92 – July 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated ADDITIONAL TERMS AND CONDITIONS, WARNINGS, RESTRICTIONS, AND DISCLAIMERS FOR EVALUATION MODULES Texas Instruments Incorporated (TI) markets, sells, and loans all evaluation boards, kits, and/or modules (EVMs) pursuant to, and user expressly acknowledges, represents, and agrees, and takes sole responsibility and risk with respect to, the following: 1. User agrees and acknowledges that EVMs are intended to be handled and used for feasibility evaluation only in laboratory and/or development environments. Notwithstanding the foregoing, in certain instances, TI makes certain EVMs available to users that do not handle and use EVMs solely for feasibility evaluation only in laboratory and/or development environments, but may use EVMs in a hobbyist environment. All EVMs made available to hobbyist users are FCC certified, as applicable. Hobbyist users acknowledge, agree, and shall comply with all applicable terms, conditions, warnings, and restrictions in this document and are subject to the disclaimer and indemnity provisions included in this document. 2. Unless otherwise indicated, EVMs are not finished products and not intended for consumer use. EVMs are intended solely for use by technically qualified electronics experts who are familiar with the dangers and application risks associated with handling electrical mechanical components, systems, and subsystems. 3. User agrees that EVMs shall not be used as, or incorporated into, all or any part of a finished product. 4. User agrees and acknowledges that certain EVMs may not be designed or manufactured by TI. 5. User must read the user's guide and all other documentation accompanying EVMs, including without limitation any warning or restriction notices, prior to handling and/or using EVMs. Such notices contain important safety information related to, for example, temperatures and voltages. For additional information on TI's environmental and/or safety programs, please visit www.ti.com/esh or contact TI. 6. User assumes all responsibility, obligation, and any corresponding liability for proper and safe handling and use of EVMs. 7. Should any EVM not meet the specifications indicated in the user’s guide or other documentation accompanying such EVM, the EVM may be returned to TI within 30 days from the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY TI TO USER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. TI SHALL NOT BE LIABLE TO USER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RELATED TO THE HANDLING OR USE OF ANY EVM. 8. No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or combination in which EVMs might be or are used. TI currently deals with a variety of customers, and therefore TI’s arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services with respect to the handling or use of EVMs. 9. User assumes sole responsibility to determine whether EVMs may be subject to any applicable federal, state, or local laws and regulatory requirements (including but not limited to U.S. Food and Drug Administration regulations, if applicable) related to its handling and use of EVMs and, if applicable, compliance in all respects with such laws and regulations. 10. User has sole responsibility to ensure the safety of any activities to be conducted by it and its employees, affiliates, contractors or designees, with respect to handling and using EVMs. Further, user is responsible to ensure that any interfaces (electronic and/or mechanical) between EVMs and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard. 11. User shall employ reasonable safeguards to ensure that user’s use of EVMs will not result in any property damage, injury or death, even if EVMs should fail to perform as described or expected. 12. User shall be solely responsible for proper disposal and recycling of EVMs consistent with all applicable federal, state, and local requirements. Certain Instructions. User shall operate EVMs within TI’s recommended specifications and environmental considerations per the user’s guide, accompanying documentation, and any other applicable requirements. Exceeding the specified ratings (including but not limited to input and output voltage, current, power, and environmental ranges) for EVMs may cause property damage, personal injury or death. If there are questions concerning these ratings, user should contact a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the applicable EVM user's guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using EVMs’ schematics located in the applicable EVM user's guide. When placing measurement probes near EVMs during normal operation, please be aware that EVMs may become very warm. As with all electronic evaluation tools, only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in development environments should use EVMs. Agreement to Defend, Indemnify and Hold Harmless. User agrees to defend, indemnify, and hold TI, its directors, officers, employees, agents, representatives, affiliates, licensors and their representatives harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of, or in connection with, any handling and/or use of EVMs. User’s indemnity shall apply whether Claims arise under law of tort or contract or any other legal theory, and even if EVMs fail to perform as described or expected. Safety-Critical or Life-Critical Applications. If user intends to use EVMs in evaluations of safety critical applications (such as life support), and a failure of a TI product considered for purchase by user for use in user’s product would reasonably be expected to cause severe personal injury or death such as devices which are classified as FDA Class III or similar classification, then user must specifically notify TI of such intent and enter into a separate Assurance and Indemnity Agreement. RADIO FREQUENCY REGULATORY COMPLIANCE INFORMATION FOR EVALUATION MODULES Texas Instruments Incorporated (TI) evaluation boards, kits, and/or modules (EVMs) and/or accompanying hardware that is marketed, sold, or loaned to users may or may not be subject to radio frequency regulations in specific countries. General Statement for EVMs Not Including a Radio For EVMs not including a radio and not subject to the U.S. Federal Communications Commission (FCC) or Industry Canada (IC) regulations, TI intends EVMs to be used only for engineering development, demonstration, or evaluation purposes. EVMs are not finished products typically fit for general consumer use. EVMs may nonetheless generate, use, or radiate radio frequency energy, but have not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC or the ICES-003 rules. Operation of such EVMs may cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may be required to correct this interference. General Statement for EVMs including a radio User Power/Frequency Use Obligations: For EVMs including a radio, the radio included in such EVMs is intended for development and/or professional use only in legally allocated frequency and power limits. Any use of radio frequencies and/or power availability in such EVMs and their development application(s) must comply with local laws governing radio spectrum allocation and power limits for such EVMs. It is the user’s sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and unauthorized by TI unless user has obtained appropriate experimental and/or development licenses from local regulatory authorities, which is the sole responsibility of the user, including its acceptable authorization. U.S. Federal Communications Commission Compliance For EVMs Annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications could void the user's authority to operate the equipment. FCC Interference Statement for Class A EVM devices This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at its own expense. FCC Interference Statement for Class B EVM devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Industry Canada Compliance (English) For EVMs Annotated as IC – INDUSTRY CANADA Compliant: This Class A or B digital apparatus complies with Canadian ICES-003. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Concerning EVMs Including Radio Transmitters This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Concerning EVMs Including Detachable Antennas Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Canada Industry Canada Compliance (French) Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de l'utilisateur pour actionner l'équipement. Concernant les EVMs avec appareils radio Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Concernant les EVMs avec antennes détachables Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated spacer Important Notice for Users of EVMs Considered “Radio Frequency Products” in Japan EVMs entering Japan are NOT certified by TI as conforming to Technical Regulations of Radio Law of Japan. If user uses EVMs in Japan, user is required by Radio Law of Japan to follow the instructions below with respect to EVMs: 1. 2. 3. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of Japan, Use EVMs only after user obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to EVMs, or Use of EVMs only after user obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect to EVMs. Also, do not transfer EVMs, unless user gives the same notice above to the transferee. Please note that if user does not follow the instructions above, user will be subject to penalties of Radio Law of Japan. http://www.tij.co.jp 【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 本開発キットは技術基準適合証明を受けておりません。 本製品の ご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。 1. 2. 3. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。 実験局の免許を取得後ご使用いただく。 技術基準適合証明を取得後ご使用いただく。。 なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします 上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・インスツルメンツ株式会社 東京都新宿区西新宿６丁目２４番１号 西新宿三井ビル http://www.tij.co.jp Texas Instruments Japan Limited (address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated