TSW14J56EVM

User's Guide SLWU086C – November 2013 – Revised January 2016 TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide The TI TSW14J56 evaluation module (EVM) is a next generation pattern generator and data capture card used to evaluate performances of the new TI JESD204B device family of high-speed analog-to-digital converters (ADC) and digital-to-analog converters (DAC). For an ADC, by capturing the sampled data over a JESD204B interface when using a high-quality, low-jitter clock, and a high-quality input frequency, the TSW14J56 can be used to demonstrate datasheet performance specifications. Using Altera JESD204B IP cores, the TSW14J56 can be dynamically configurable to support lane speeds from 600 Mbps to 12.5 Gbps, from 1 to 8 lanes, 1 to 16 converters, and 1 to 4 octets per frame with one firmware build. Together with the accompanying High-Speed Data Converter Pro Graphic User Interface (GUI), it is a complete system that captures and evaluates data samples from ADC EVMs and generates and sends desired test patterns to DAC EVMs. Trademarks Windows is a trademark of Microsoft Corporation. 1 Functionality The TSW14J56EVM has a single industry standard FMC connector that interfaces directly with TI JESD204B ADC and DAC EVM's. When used with an ADC EVM, high-speed serial data is captured, deserialized and formatted by an Altera Arria V GZ FPGA. The data is then stored into an external DDR3 memory bank, enabling the TSW14J56 to store up to 2G 16-bit data samples. To acquire data on a host PC, the FPGA reads the data from memory and transmits it on a high speed 32 bit parallel interface. An onboard high-speed USB 3.0 to parallel converter bridges the FPGA interface to the host PC and GUI. In pattern generator mode, the TSW14J56 generates desired test patterns for DAC EVMs under test. These patterns are sent from the host PC over the USB interface to the TSW14J56. The FPGA stores the data received into the board DDR3 memory module. The data from memory is then read by the FPGA and transmitted to a DAC EVM across the JESD204B interface connector. The board contains a 100-MHz oscillator used to generate the DDR3 reference clock and a option for a 10-MHz oscillator for general purpose use. Figure 1 shows the TI ADS58J63EVM plugged into the TSW14J56EVM. SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide Copyright © 2013–2016, Texas Instruments Incorporated 1 Functionality www.ti.com Figure 1. TSW14J56EVM Interfacing with an ADS58J63EVM The major features of the TSW14J56 are: • Subclasses: 0 (backward compatible), 1, 2 • Support for deterministic latency • Serial lanes speeds up to 12.5 Gbps • 10 routed transceiver channels • 32 Gb DDR3 SDRAM (split into four independent 512×164 Gb SDRAMs, total of 512M samples each). Quarter rate DDR3 controllers supporting up to 800-MHz operation • 256K 16-bit samples of internal FPGA memory • Supports 1.8, 2.5 and 3-V adjustable CMOS IO standard • Option for general purposed 10 MH oscillator • Onboard UCD90120A for power sequencing and monitoring • Onboard Cypress CYUSB301X USB 3.0 device for JTAG and parallel interface to the FPGA • Reference clocking for transceivers available through FMC port or SMAs • Supported by TI HSDC PRO software • FPGA firmware developed with Quartus II 14.0 and QSYS 2 TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback Copyright © 2013–2016, Texas Instruments Incorporated Functionality www.ti.com – JESD RX IP core with support for: • USB and JTAG reconfigurable JESD core parameters: L, M, K, F, HD, S, and more • ILA configuration data accessible through USB and JTAG • Lane alignment and character replacement enabled or disabled through USB and JTAG – JESD TX IP core with support for: • USB and JTAG reconfigurable JESD core parameters: L, M, K, F, HD, S, and more • ILA data configured through USB and JTAG • Character replacement enabled or disabled through USB and JTAG – Dynamically reconfigurable transceiver data rate. Operating range from 0.600 to 12.5 Gbps Figure 2 shows a block diagram of the TSW14J56 EVM. TSW14J56 EVM +5 VDC Input Power Sequencer/ Monitor 32Gb DDR III RAM LDO and Switch Regulators ALTERA Arria V GZ (Firmware) 32 Bit 100 MHz Parallel Interface JESD204B Interface Data, Device CLK, SYSREF, SYNC, GPIO USB to Parallel USB 3.0 Port FMC Connector ADC or DAC EVM Figure 2. TSW14J56 EVM Block Diagram 1.1 ADC EVM Data Capture New TI high-speed ADCs and DACs now have high-speed serial data that meets the JESD204B standard. These devices are generally available on an EVM that connects directly to the TSW14J56EVM. The common connector between the EVMs and the TSW14J56EVM is a Samtec high-speed, high-density FMC connector (SEAF-40-05.0-S-10-2-A-K) suitable for high-speed differential pairs up to 21 Gbps. A common pinout for the connector across a family of EVMs has been established. At present, the interface between the EVMs and the TSW14J56EVM has defined connections for 10 lanes of serial differential data, two device clock pairs, two JESD204B SYSREF and SYNC pairs. There are four over-range singleended indicators, 12 spare general purpose CMOS I/O pins, and 29 spare differential LVDS or 58 singleended CMOS signals. The board has a spare SMA interface to the FPGA, 4 spare dip switches, a pushbutton switch, several spare test points routed to the FPGA and 8 status LED's. SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide Copyright © 2013–2016, Texas Instruments Incorporated 3 Functionality www.ti.com The data format for JESD204B ADCs and DACs is a serialized format, where individual bits of the data are presented on the serial pairs commonly referred to as lanes. Devices designed around the JESD204B spec can have up to 8 lanes for transmitting or receiving data. The firmware in the FPGA on the TSW14J56 is designed to accommodate any of TI's ADC or DAC operating with any number of lanes from 1 to 8. The GUI loads the FPGA with the appropriate firmware and a specific JESD204B configuration, based on the ADC device selected in the device drop down window. Each ADC device that appears in this window has an initialization file (.ini) associated to it. This .ini file contains JESD information, such as number of lanes, number of converters, octets per frame, and other parameters. This information is loaded into the FPGA registers after the user clicks on the capture button. After the parameters are loaded, synchronization is established between the data converter and FPGA and valid data is then captured into the on-board memory. See the High-Speed Data Capture Pro GUI Software User's Guide SLWU087 and section 2.3 in the guide for more information. Several .ini files are available to allow the user to load predetermined ADC JESD204B interfaces. For example, if the user selects the ADC called "ADS42JB69_LMF_421", the FPGA will be configured to capture data from the ADS42JB69EVM with the ADC JESD interface configured for 4 lanes, 2 converters, and 1 octet per frame. The TSW14J56 device can capture up to 2G 16-bit samples at a maximum line rate of 12.5 Gbps that are stored inside the on-board DDR3 memory. To acquire data on a host PC, the FPGA reads the data from memory and transmits parallel data to the on-board high-speed parallel-to-USB converter. 1.2 DAC EVM Pattern Generator In pattern generator mode, the TSW14J56EVM generates desired test patterns for DAC EVMs under test. These patterns are sent from the host PC over the USB interface to the TSW14J56. The FPGA stores the data received into the on-board DDR3 memory. The data from the memory is then read by the FPGA, converted to JESD204B serial format, then transmitted to a DAC EVM. The TSW14J56 can generate patterns up to 2G 16-bit samples at a line rate up to 12.5 Gbps. The GUI comes with several existing test patterns that can be download immediately. The GUI also has a pattern generation tool that allows the user to generate a custom pattern, then download it to the on-board memory. See the High-Speed Data Capture Pro Software User's Guide SLWU087 for more information. Like the ADC capture mode, the DAC pattern generator mode uses .ini files to load predetermined JESD204B interface information to the FPGA. 2 Hardware Configuration This section describes the various portions of the TSW14J56EVM hardware. 2.1 Power Connections The TSW14J56EVM hardware is designed to operate from a single supply voltage of +5 V DC. The power input is controlled by the on and off switch, SW6. Make sure this switch is in the off position before inserting the provided power cable. Insert the connector end of the power cable into J11 of the EVM. Connect the positive red wire end of the power cable to +5V +/- 0.3VDC output of a +5VDC power supply rated for at least 3 Amps. Connect the negative black wire to the RETURN or GND of the power supply. The board can also be powered up by providing +5 V DC to the red test point, TP34, and the return to any black GND test point. The TSW14J56 draws approximately 0.6 A at power-up and 1.6 A when capturing 4 lanes of data from an ADS42JB69EVM at a line rate of 2.5 Gpbs. 4 TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback Copyright © 2013–2016, Texas Instruments Incorporated Hardware Configuration www.ti.com 2.2 2.2.1 Switches, Jumpers, and LEDs Switches and Pushbuttons The TSW14J56 contains several switches and pushbuttons that enable certain functions on the board. The description of the switches can be found in Table 1. Table 1. Switch Description of the TSW14J56 Device Component 2.2.2 Description SW6 Board main power switch SW1 Spare dip switches that are connected to spare FPGA inputs SW2 Spare pushbutton that are connected to spare FPGA inputs SW7 (CPU RESET) FPGA hardware reset SW10 Dip switch to set VAR adjustable regulator output voltage. Default is 1.8V (switches 1,3,4 off, 2 on) SW11 USB hardware reset SW9 (UCD Reset) Power monitor U13 reset Jumpers The TSW14J56 contains several jumpers (JP) and solder jumpers (SJP) that enable certain functions on the board. The description of the jumpers can be found in Table 2. Table 2. Jumper Description of the TSW14J56 Device Component Description Default SJP1 Power enable to general purpose 10-MHz oscillator Y1 1 to 2 SJP19 - SJP21 Address for spare I2C controller U42 2 to 3 SJ14, SJ15, SJ18 Sets programming mode for FPGA 2 to 3 SJ16, SJ17 Sets programming mode for FPGA 1 to 2 JP4, JP5, JP6, and JP7 USB or JTAG control of FPGA programming. Default is USB control 2 to 3 JP16 USB cable or internal 5-V power for USB interface. Default is USB cable power 2 to 3 JP14 5-V supply for U39. Default is no power Not installed JP15 U39 output used for power. Default is disabled Not installed JP17 U39 enable. 2 to 3 SJP2, SJP3 Direction control for buffer U29. Default is B to A 2 to 3 SJP9 Direction control for buffer U30. Default is B to A 2 to 3 SJP10, SJP11 Direction control for buffer U41. Default is B to A 2 to 3 SJP12, SJ13 Direction control for buffer U28. Default is B to A 2 to 3 JP11 Programming mode for USB controller U33 1 to 2 JP12 Programming mode for USB controller U33 Not installed JP13 Programming mode for USB controller U33 2 to 3 JP10 USB TCK routing option 2 to 3 J17 USB Controller U33 to Flash U36 interface. 3 to 4, 5 to 6, 7 to 8, 9 to 10 SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide Copyright © 2013–2016, Texas Instruments Incorporated 5 Hardware Configuration 2.3 www.ti.com LEDs 2.3.1 Power and Configuration LEDs Several LEDs are on the TSW14J56 EVM to indicate the presence of power and the state of the FPGA. The description of these LEDs can be found in Table 3. Table 3. Power and Configuration LED Description of the TSW14J56 Device Component 2.3.2 Description D17 On if DDR3 VREF power is good D10 On if 5V board power is present D32 On if power monitor device indicates that a power net is out of tolerance D11 On if +1.0 V is within specification D13 On if VCCD_1.5 V is within specification D16 On if VCC_1.5 V is within specification D21 On if VCC_2.5 V is within specification D23 On if VCCA_GXB_3.0 V is within specification D25 On if VCC_PLL_2.5 V is within specification D26 On if VCC_0.85V is within specification D27 On if VCCDDR_1.5 V is within specification D30 On if VTTDDR_0.75 V is within specification D34 On if VAR power is present D33 On if USB_1.2 V is within specification D28 On after FPGA completes configuration Status LEDs Eight status LEDs on the TSW14J56EVM indicate the status of the FPGA, DDR3, and JESD204B interface: D1 – Indicates DAC EVM established SYNC with the TSW14J56 device when off D2 – Indicates presence of device clock from DAC EVM when blinking D3 – Indicates ADC EVM established SYNC with the TSW14J56 device when off D4 – Indicates presence of device clock from ADC EVM when blinking D5 – Not used D6 – DDR3 initialization and calibration complete when off D7 – DDR3 ready when off D8 – DDR3 pass calibration and initialization if on 2.3.3 Connectors 2.3.3.1 SMA Connectors The TSW14J56 has 9 SMA connectors. The connectors are defined below: J6 J5 J13 J7 J8 6 GBTCLK0N GBTCLK0P TRIG_IN TRIG_OUT_A TRIG_OUT_B Spare Transceiver reference clock negative input Spare Transceiver reference clock positive input Adjustable level CMOS trigger input. Default level is 1.8 V Adjustable level CMOS trigger output. Default level is 1.8 V Adjustable level CMOS trigger output. Default level is 1.8 V TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback Copyright © 2013–2016, Texas Instruments Incorporated Hardware Configuration www.ti.com J12 J3 J14 J15 2.3.3.2 TRIG_OUT_C REF_OSC_IN EXT_SYSREFP EXT_SYSREFN Adjustable level CMOS trigger output. Default level is 1.8 V AC coupled spare input connected to FPGA CLK input Spare SYSREF positive input to FPGA Spare SYSREF negative input to FPGA FPGA Mezzanine Card (FMC) Connector The TSW14J56 EVM has one connector to allow for the direct plug in of TI JESD204B serial interface ADC and DAC EVMs. The specifications for this connector are mostly derived from the ANSI/VITA 57.1 FPGA Mezzanine Card (FMC) Standard. This standard describes the compliance requirements for a lowoverhead protocol bridge between the IO of a mezzanine card and an FPGA processing device on a carrier card. This specification is being used by FPGA vendors on their development platforms. The FMC connector, J4, provides the interface between the TSW14J56EVM and the ADC or DAC EVM under test. This 400-pin Samtec high-speed, high-density connector (part number SEAF-40-05.0-S-10-2A-K) is suitable for high-speed differential pairs up to 21 Gbps. In addition to the JESD204B standard signals, several CMOS single-ended signals and LVDS differential signals are connected between the FMC and FPGA. In the future, these signals may allow the HSDC Pro GUI to control the SPI serial programming of ADC and DAC EVMs that support this feature. The connector pinout description is shown in Table 4. Table 4. FMC Connector Description of the TSW14J56 FMC Signal Name FMC Pin Standard JESD204 Application Mapping Description RX0_P/N C6 and C7 Lane 0± (M → C) JESD Serial data transmitted from mezzanine and received by carrier RX1_P/N A2 and A3 Lane 1± (M → C) JESD Serial data transmitted from mezzanine and received by carrier RX2_P/N A6 and A7 Lane 2± (M → C) JESD Serial data transmitted from mezzanine and received by carrier RX3_P/N A10 and A11 Lane 3± (M → C) JESD Serial data transmitted from mezzanine and received by carrier RX4_P/N A14 and A15 Lane 4± (M → C) JESD Serial data transmitted from mezzanine and received by carrier RX5_P/N A18 and A19 Lane 5± (M → C) JESD Serial data transmitted from mezzanine and received by carrier RX6_P/N B16 and B17 Lane 6± (M → C) JESD Serial data transmitted from mezzanine and received by carrier RX7_P/N B12 and B13 Lane 7± (M → C) JESD Serial data transmitted from mezzanine and received by carrier RX8_P/N B8 and B9 Lane 8± (M → C) JESD Serial data transmitted from mezzanine and received by carrier RX9_P/N B4 and B5 Lane 9± (M → C) JESD Serial data transmitted from mezzanine and received by carrier TX0_P/N C2 and C3 Lane 0± (C → M) JESD Serial data transmitted from carrier and received by mezzanine TX1_P/N A22 and A23 Lane 1± (C → M) JESD Serial data transmitted from carrier and received by mezzanine TX2_P/N A26 and A27 Lane 2± (C → M) JESD Serial data transmitted from carrier and received by mezzanine TX3_P/N A30 and A31 Lane 3± (C → M) JESD Serial data transmitted from carrier and received by mezzanine TX4_P/N A34 and A35 Lane 4± (C → M) JESD Serial data transmitted from carrier and received by mezzanine TX5_P/N A38 and A39 Lane 5± (C → M) JESD Serial data transmitted from carrier and received by mezzanine SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide Copyright © 2013–2016, Texas Instruments Incorporated 7 Hardware Configuration www.ti.com Table 4. FMC Connector Description of the TSW14J56 (continued) FMC Signal Name FMC Pin Standard JESD204 Application Mapping Description TX6_P/N B36 and B37 Lane 6± (C → M) JESD Serial data transmitted from carrier and received by mezzanine TX7_P/N B32 and B33 Lane 7± (C → M) JESD Serial data transmitted from carrier and received by mezzanine TX8_P/N B28 and B29 Lane 8± (C → M) JESD Serial data transmitted from carrier and received by mezzanine TX9_P/N B24 and B25 Lane 9± (C → M) JESD Serial data transmitted from carrier and received by mezzanine GBTCLK0_M2C_P/N D4 and D5 DEVCLKA± (M → C) Primary carrier-bound reference clock required for FPGA giga-bit transceivers. Equivalent to device clock. GBTCLK1_M2C_P/N B20 and B21 Alt. DEVCLKA± (M → C) Alternate Primary Carrier-bound reference clock required for FPGA giga-bit transceivers. For use when DEVCLKA (M → C) is not available CLK_LA0_P/N G6 and G7 DEVCLKB± (M → C) Secondary carrier-bound device clock. Used for special FPGA functions such as sampling SYSREF LA01_P/N_CC D8 and D9 DEVCLK± (C → M) Mezzanine-bound device clock. Used for low noise conversion clock SYSREF_P/N G9 and G10 SYSREF± (M → C) Carrier-bound SYSREF signal LA05_P/N D11 and D12 SYSREF± (C → M) Mezzanine-bound SYSREF signal RX_SYNC_P/N G12 and G13 SYNC± (C → M) ADC mezzanine-bound SYNC signal for use in class 0/1/2 JESD204 systems TX_SYNC_P/N F10 and F11 DAC SYNC± (M → C) Carrier-bound SYNC signal for use in class 0/1/2 JESD204 systems TX_ALT_SYNC_P/N F19 and F20 Alt. DAC SYNC± (M → C) Alternate carrier-bound SYNC signal for use in class 0/1/2 JESD204B systems RX_ALT_SYNC_P/N H31 and H32 Alt. SYNC± (C → M) Alternate ADC mezzanine-bound SYNC signal. For use when SYNC (C → M) is not available SYNC K22 DAC SYNC (M → C) Carrier-bound CMOS-level SYNC signal for use in class 0/1/2 JESD204 systems PG_M2C_A F1 Power good from mezzanine to carrier CLK0_M2C_P/N H4 and H5 GPIO clock CLK1_M2C_P/N G2 and G3 GPIO clock Device Clock, SYSREF, and SYNC Special Purpose I/O All other signals not mentioned in Table 4 can be used as general purpose I/O, either as single-ended signals or differential pairs. The ANSI/VITA 57.1 standard assigns voltages to certain pins. These are labeled as 12V, 3P3V, and VADJ nets on the connector page of the schematic. On the TSW14J56, these pins are connected to test points to allow the user to provide voltages at these pin locations. 8 TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback Copyright © 2013–2016, Texas Instruments Incorporated Hardware Configuration www.ti.com 2.3.3.3 JTAG Connectors The TSW14J56EVM includes three industry-standard JTAG connectors; one that connects to the JTAG ports of the FPGA, one that connects to the JTAG pins of the Cypress FX3 USB Contoller and the other that connects to the programming pins of the power monitor/sequencer device. Jumpers on the TSW14J56EVM allow for the FPGA to be programmed from the JTAG connector or the USB interface. JTAG connectors J2, J10 and J16 are to be used for troubleshooting only. The board default setup is with the FPGA JTAG pins connected to JTAG connector J16. The FPGA can be programmed using this connector if the MSEL inputs are set to the proper logic levels. These are set by solder jumpers SJP1418. Consult the Altera data sheet for more information regarding JTAG programming. The FPGA also has the parallel programming inputs connected to the USB 3.0 controller. With SJP14-18 in teh default postions, this allows the FPGA to be programmed by the HSDC Pro software GUI. Every time the TSW14J56EVM is powered-down, the FPGA configuration is removed. The user must program the FPGA through the GUI after every time the board is powered-up. J2 can be used to program the USB controller U33. This device is programmed at power-up using the factory pre-programmed flash device U36. JTAG connector J10 is used to program the TI UCD90120A power monitor/sequencer device. This device is preprogrammed at the factory and this interface should only be used for troubleshooting. 2.3.3.4 USB I/O Connection Control of the TSW14J56EVM is through USB 3.0 connector J9. This provides the interface between HSDC Pro GUI running on a PC Windows™ operating system and the FPGA. For the computer, the drivers needed to access the USB port are included on the HSDC Pro GUI installation software that can be downloaded from the web. The drivers are automatically installed during the installation process. On the TSW14J56EVM, the USB port is used to identify the type and serial number of the EVM under test, load the desired FPGA configuration file, capture data from ADC EVMs, and send test pattern data to the DAC EVMs. SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide Copyright © 2013–2016, Texas Instruments Incorporated 9 Software Start-Up www.ti.com 3 Software Start-Up 3.1 Installation Instructions Download the latest version of the HSDC Pro GUI (slwc107x.zip) to a local location on a host PC. Visit www.ti.com and find the install link on the TSW14J56EVM page. Unzipping the software package generates a folder called “High Speed Data Converter Pro - Installer vx.xx.exe", where x.xx is the version number. Run this program to start the installation. Follow the on-screen instructions during installation. NOTE: If an older version of the GUI has already been installed, make sure to uninstall it before loading a newer version. Figure 3. GUI Installation Make sure to disconnect all USB cables from any TSW14xxx boards before installing the software. Follow all on-screen instructions. Accept the license agreements. After the installer has finished, click “Next”. The GUI executable and associated files reside in the following directory: C:\Program Files (x86)\Texas Instruments\High Speed Data Converter Pro. 3.2 USB Interface and Drivers • • • Connect a USB 3.0 cable between J9 of the TSW14J56EVM and a host PC. Connect the provided power cable between the EVM and a +5 VDC source. Set SW6 to on. Click on the High-Speed Data Converter Pro icon that was created on the desktop panel, or go to C:\Program Files (x86)\Texas Instruments\High Speed Data Converter Pro and double click on the executable called “High Speed Data Converter Pro.exe” to start the GUI. The GUI first attempts to connect to the EVM USB interface. If the GUI identifies a valid board serial number, a pop-up opens displaying this value, as shown in Figure 4. The user can connect several TSW14J56 EVMs to one host PC, but the GUI can only connect to one at a time. When multiple boards are connected to the PC, the pop-up displays all of the serial numbers found. The user then selects which board to associate the GUI with. 10 TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback Copyright © 2013–2016, Texas Instruments Incorporated Software Start-Up www.ti.com Figure 4. TSW14J56EVM Serial Number Click “OK” to connect the GUI to the board. The top level GUI opens and appears as shown in Figure 5. Figure 5. High-Speed Data Converter Pro GUI Top Level If the message “No Board Connected” opens, double check the USB cable connections and that power switch SW6 is in the on position. Remove the USB cable from the board then re-install. Click on the “Instrument Option” tab at the top left of the GUI and selecting “Connect to the Board”. If this still does not correct this issue, check the status of the host USB port. When the software is installed and the USB cable is connected to the TSW14J56EVM and the PC, the TSW14J56 USB 3.0 converter should be located in the Hardware Device Manager under the universal serial bus controllers as shown in Figure 6 labeled as Cypress FX3 USB StreamerExample Device. When the USB 3.0 cable is removed, this driver will no longer be visible in the device manager. If the drivers are present in the device manager window and the software still does not connect, remove the USB 3.0 cable from the board then reconnect. Attempt to connect to the board. If the problem still exists, cycle power to the board and repeat the prior steps. SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide Copyright © 2013–2016, Texas Instruments Incorporated 11 Downloading Firmware www.ti.com Figure 6. Hardware Device Manager 4 Downloading Firmware The TSW14J56EVM has an Altera Arria V GZ device that requires firmware to be downloaded every time power is cycled to operate. The firmware files needed are special .rbf formatted files that are provided with the software package. The files used by the GUI currently reside in the directory called C:\Program Files (x86)\Texas Instruments\High Speed Data Converter Pro\14J56revD Details\Firmware. To load a firmware, after the GUI has established connection, click the “Select ADC” window in the top left of the GUI and select the device to evaluate, for example, ADS42JB69_LMF_421, as shown in Figure 7. The GUI prompts the user to update the firmware for the ADC. Click "Yes”. The GUI will display the message "Downloading Firmware, Please Wait". The software now loads the firmware from the PC to the FPGA, a process that takes about 3 seconds. Once completed, the GUI reports an Interface Type in the lower right corner and the FPGA_CONF_DONE LED (D28) illuminates along with several of the status LEDs. Figure 7. Select ADC Firmware to be Loaded 12 TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback Copyright © 2013–2016, Texas Instruments Incorporated Downloading Firmware www.ti.com For information regarding the use of the TSW14J56EVM with a TI ADC or DAC JESD204B serial interface EVM, consult the High-Speed Data Converter Pro GUI User's Guide SLWU087 and the individual EVM User’s Guide, available on www.ti.com. If the message appears as shown in Figure 8, verify that all jumpers are in the default position and all power status LEDs are illuminated. If certain jumpers are not installed in the proper location, the USB 3.0 Controller will not boot from flash memory. If any power status LED is off, there may be a problem with a power supply on the board, which can prevent the firmware from downloading. Unplug and re-install the USB connector and try to connect to the board. If this fails, cycle the power switch to re-initialize the power-up sequencer to try to correct this problem. Figure 8. Download Firmware Error Message SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback TSW14J56 JESD204B High-Speed Data Capture and Pattern Generator Card User's Guide Copyright © 2013–2016, Texas Instruments Incorporated 13 Revision History www.ti.com Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from B Revision (July 2015) to C Revision ..................................................................................................... Page • • Changed Power Connections section to remove included power supply. ......................................................... 4 Removed reference to provided +5VDC source in the USB Interface and Drivers section. ................................... 10 Revision History Changes from A Revision (November 2013) to B Revision ........................................................................................... Page • • • • • • • Changed TSW14J56EVM Interfacing with an ADS42JB49EVM image. ........................................................... 2 Changed TSW14J56 EVM Block Diagram image. .................................................................................... 3 Changed TSW14J56EVM Serial Number image. ................................................................................... 11 Changed High-Speed Data Converter Pro GUI Top Level image. ................................................................ 11 Changed Hardware Device Manager image. ........................................................................................ 12 Changed Select ADC Firmware to be Loaded image. .............................................................................. 12 Changed Download Firmware Error Message image. .............................................................................. 13 Revision History Changes from Original (November 2013) to A Revision ................................................................................................ Page • • 14 Added the number of converters and octets ........................................................................................... 1 Added a link to the High-Speed Data Converter Pro GUI ........................................................................... 1 Revision History SLWU086C – November 2013 – Revised January 2016 Submit Documentation Feedback Copyright © 2013–2016, Texas Instruments Incorporated IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you (individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of this Notice. TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications (and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your noncompliance with the terms and provisions of this Notice. This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services. These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation modules, and samples (http://www.ti.com/sc/docs/sampterms.htm). Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2018, Texas Instruments Incorporated