UC2710NG4

UC1710 UC2710 UC3710 High Current FET Driver FEATURES DESCRIPTION • Totem Pole Output with 6A Source/Sink Drive The UC1710 family of FET drivers is made with a high-speed Schottky process to interface between low-level control functions and very high-power switching devices-particularly power MOSFET’s. These devices accept low-current digital inputs to activate a high-current, totem pole output which can source or sink a minimum of 6A. • 3ns Delay • 20ns Rise and Fall Time into 2.2nF • 8ns Rise and Fall Time into 30nF • 4.7V to 18V Operation • Inverting and Non-Inverting Outputs • Under-Voltage Lockout with Hysteresis • Thermal Shutdown Protection Supply voltages for both VIN and VC can independently range from 4.7V to 18V. These devices also feature under-voltage lockout with hysteresis. The UC1710 is packaged in an 8-pin hermetically sealed dual in-line package for –55°C to +125°C operation. The UC2710 and UC3710 are specified for a temperature range of –40°C to +85°C and 0°C to +70°C respectively and are available in either an 8-pin plastic dual in-line or a 5-pin, TO-220 package. Surface mount devices are also available. • MINIDIP and Power Packages ORDERING INFORMATION TRUTH TABLE INV N.I. Out H H L OUT= INV and N.I. L H H OUT= INV or N.I. H L L L L L UC1710J UC2710DW UC2710J UC2710N UC2710T UC3710DW UC3710N UC3710T TEMPERATURE RANGE –55°C to +125°C –40°C to +85°C 0°C to +70°C PACKAGE 8 pin CDIP Not Available Not Available 8 pin PDIP 5 pin TO220 16 pin SOIC-wide 8 pin PDIP 5 pin TO220 BLOCK DIAGRAM INTERNALLY CONNECTED IN T PACKAGE VIN 5 OUTPUT BIAS 4 VC 3 Out 2 Pwr Gnd LOGIC BIAS N.I. IN 8 INV IN 1 Logic Gnd 7 TSD UVLO INTERNALLY CONNECTED IN T PACKAGE UDG-99079 05/99 UC1710 UC2710 UC3710 ABSOLUTE MAXIMUM RATINGS N-Package J-Package T-Package Supply Voltage, Vin . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V Collector Supply Voltage, VC . . . . . . . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V . . . . . . . . . . . . . . 18V . . . . . . . . . . . . . . 18V Output Current (Source or Sink) Steady-State. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 500mA. . . . . . . . . . . . ± 500mA . . . . . . . . . . . . . ± 1A Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3V-VIN . . . . . . . . –0.3V – VIN . . . . . . . . –0.3V – VIN Power Dissipation at Ta=25°C . . . . . . . . . . . . . . . . . . . 1W . . . . . . . . . . . . . . . 1W . . . . . . . . . . . . . . . 3W Power Dissipation at T (Case) = 25°C. . . . . . . . . . . . . . 2W . . . . . . . . . . . . . . . 2W . . . . . . . . . . . . . . 25W Operating Junction Temperature . . . . . . . –55°C to +150°C . . . . –55°C to +150°C . . . . –55°C to +150°C Storage Temperature . . . . . . . . . . . . . . . –65°C to +150°C . . . . –65°C to +150°C . . . . –65°C to +150°C Lead Temperature (Soldering, 10 seconds) . . . . . . . 300°C . . . . . . . . . . . . 300°C . . . . . . . . . . . . 300°C Note 1: All currents are positive into, negative out of the specified terminal. Note 2: Consult Unitrode Integrated Circuits databook for information regarding thermal specifications and limitations of packages. CONNECTION DIAGRAMS DIL-8 MINIDIP (Top View) J or N Package SOIC-16 (Top View) DW Package 5-Pin TO-220 (Top View) T Package ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for VIN = VC = 15V, No load, TA = TJ. PARAMETERS VIN Supply Current VC Supply Current UVLO Threshold TEST CONDITIONS MIN TYP MAX UNITS VIN =18V, VC =18V, Output Low 26 35 mA VIN =18V, VC =18V, Output High 21 30 mA VIN =18V, VC =18V, Output Low 1.5 5.0 mA VIN =18V, VC =18V,Output High 5.0 8 mA VIN High to Low 3.8 4.1 4.4 V VIN Low to High 4.1 4.4 4.8 V 2 UC1710 UC2710 UC3710 ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for VIN = VC = 15V, No load, TA = TJ. PARAMETERS TEST CONDITIONS UVLO Threshold Hysteresis MIN TYP 0.1 0.3 Digital Input Low Level Digital Input High Level MAX UNITS 0.5 V 0.8 V 2.0 Digital Input = 0.0V Output High Sat., VC – VO IO= –100mA 1.35 2.2 V IO= –6A 3.2 4.5 V IO= 100mA 0.25 0.6 V IO= 6A 3.4 4.5 V Output Low Sat., VO Thermal Shutdown –70 V Digital Input Current –4.0 µA 165 °C From Inv., Input to Output (Note 3, 4): Rise Time Delay 10% to 90% Rise Fall Time Delay 90% to 10% Fall CL = 0 35 70 ns CL = 2.2nF 35 70 ns CL = 30nF 35 70 ns CL = 0 20 40 ns CL = 2.2nF 25 40 ns CL = 30nF 85 150 ns CL = 0 35 70 ns CL = 2.2nF 35 70 ns CL = 30nF 35 80 ns CL = 0 15 40 ns CL = 2.2nF 20 40 ns CL = 30nF 85 150 ns CL = 0 35 70 ns From N.I. Input to Output (Note 3,4): Rise Time Delay 10% to 90% Rise Fall Time Delay 90% to 10% Fall Total Supply Current at 200kHz Input Switching Frequency CL = 2.2nF 35 70 ns CL = 30nF 35 70 ns CL = 0 20 40 ns CL = 2.2nF 25 40 ns CL = 30nF 85 150 ns CL = 0 35 70 ns CL = 2.2nF 35 70 ns CL = 30nF 35 80 ns CL = 0 15 40 ns CL = 2.2nF 20 50 ns CL = 30nF 85 150 ns TA = 25°C (Note 5) CL = 0 30 40 mA Note: 3. Delay measured from 50% input change to 10% output change. Note: 4. Those parameters with CL = 30nF are not tested in production. Note: 5. Inv. Input pulsed at 50% duty cycle with N.I. Input = 3V. or N.I. Input pulsed at 50% duty cycle with Inv. Input = 0V. UNITRODE CORPORATION 7 CONTINENTAL BLVD. • MERRIMACK, NH 03054 TEL. (603) 424-2410 FAX (603) 424-3460 3 PACKAGE OPTION ADDENDUM 8-Apr-2018 www.ti.com PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) 5962-0152001QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 0152001QPA UC1710 5962-0152001VPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 0152001VPA UC1710 UC1710J ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 UC1710J UC1710J883B ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 0152001QPA UC1710 UC2710N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type -40 to 85 UC2710N UC2710NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type -40 to 85 UC2710N UC2710T ACTIVE TO-220 KC 5 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type -40 to 85 UC2710T UC2710TG3 ACTIVE TO-220 KC 5 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type -40 to 85 UC2710T UC3710DW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 0 to 70 UC3710DW UC3710DWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 0 to 70 UC3710DW UC3710N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU | Call TI N / A for Pkg Type 0 to 70 UC3710N UC3710NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) Call TI N / A for Pkg Type 0 to 70 UC3710N UC3710T ACTIVE TO-220 KC 5 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type 0 to 70 UC3710T UC3710TG3 ACTIVE TO-220 KC 5 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type 0 to 70 UC3710T (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM 8-Apr-2018 www.ti.com (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of