UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
HIGH-SPEED PWM CONTROLLER
FEATURES
D Improved Versions of the UC3823/UC3825
D
D
D
D
DESCRIPTION
The UC3823A and UC3823B and the UC3825A and
UC3825B family of PWM controllers are improved
versions of the standard UC3823 and UC3825 family.
Performance enhancements have been made to several
of the circuit blocks. Error amplifier gain bandwidth product
is 12 MHz, while input offset voltage is 2 mV. Current limit
threshold is assured to a tolerance of 5%. Oscillator
discharge current is specified at 10 mA for accurate dead
time control. Frequency accuracy is improved to 6%.
Startup supply current, typically 100 μA, is ideal for off-line
applications. The output drivers are redesigned to actively
sink current during UVLO at no expense to the startup
current specification. In addition each output is capable of
2-A peak currents during transitions.
PWMs
Compatible with Voltage-Mode or
Current-Mode Control Methods
Practical Operation at Switching Frequencies
to 1 MHz
50-ns Propagation Delay to Output
High-Current Dual Totem Pole Outputs
(2-A Peak)
Trimmed Oscillator Discharge Current
D
D Low 100-μA Startup Current
D Pulse-by-Pulse Current Limiting Comparator
D Latched Overcurrent Comparator With Full
Cycle Restart
BLOCK DIAGRAM
CLK/LEB 4
13 VC
(60%)
RT 5
CT 6
R
RAMP 7
EAOUT 3
NI
11 OUTA
*
OSC
T
SD
PWM
LATCH
1.25 V
PWM COMPARATOR
14 OUTB
12 PGND
2
E/A
9 mA
INV 1
SOFT−START COMPLETE
SS 8
CURRENT
LIMIT
1.0 V
OVER CURRENT
ILIM 9
1.2 V
RESTART
DELAY
0.2 V
VCC 15
GND 10
RESTART
DELAY
LATCH
5V
”B” 16V/10V
”A” 9.2V/8.4V
SD
S
R
R
250 mA
FAULT LATCH
UVLO
VREF
5.1 V
ON/OFF
* On the UC1823A version, toggles Q and Q are always low.
4V
VREF GOOD
INTERNAL
BIAS
16 5.1 VREF
UDG−02091
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Products
conform to specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all parameters.
Copyright © 2004 −2008, Texas Instruments Incorporated
UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during
storage or handling to prevent electrostatic damage to the MOS gates.
DESCRIPTION (CONTINUED)
Functional improvements have also been implemented in this family. The UC3825 shutdown comparator is now a
high-speed overcurrent comparator with a threshold of 1.2 V. The overcurrent comparator sets a latch that ensures full
discharge of the soft-start capacitor before allowing a restart. While the fault latch is set, the outputs are in the low state.
In the event of continuous faults, the soft-start capacitor is fully charged before discharge to insure that the fault frequency
does not exceed the designed soft start period. The UC3825 CLOCK pin has become CLK/LEB. This pin combines the
functions of clock output and leading edge blanking adjustment and has been buffered for easier interfacing.
The UC3825A and UC3825B have dual alternating outputs and the same pin configuration of the UC3825. The UC3823A
and UC3823B outputs operate in phase with duty cycles from zero to less than 100%. The pin configuration of the UC3823A
and UC3823B is the same as the UC3823 except pin 11 is now an output pin instead of the reference pin to the current
limit comparator. “A” version parts have UVLO thresholds identical to the original UC3823 and UC3825. The “B” versions
have UVLO thresholds of 16 V and 10 V, intended for ease of use in off-line applications.
Consult the application note, The UC3823A,B and UC3825A,B Enhanced Generation of PWM Controllers, (SLUA125) for
detailed technical and applications information.
ORDERING INFORMATION
UVLO
MAXIMUM
DUTY CYCLE
TA
−40°C
40°C to 85°C
−0°C
0°C to 70°C
(1)
9.2 V / 8.4 V
16 V / 10 V
SOIC−16(1)
(DW)
PDIP−16
(N)
PLCC−20(1)
(Q)
SOIC−16
(DW)
PDIP−16
(N)
PLCC−20(1)
(Q)
< 100%
UC2823ADW
UC2823AN
UC2823AQ
UC2823BDW
UC2823BN
−
< 50%
UC2825ADW
UC2825AN
UC2825AQ
UC2825BDW
UC2825BN
−
< 100%
UC3823ADW
UC3823AN
UC3823AQ
UC3823BDW
UC3823BN
−
< 50%
UC3825ADW
UC3825AN
UC3825AQ
UC3825BDW
UC3825BN
UC3825BQ
The DW and Q packages are also available taped and reeled. Add TR suffix to the device type (i.e., UC2823ADWR). To order quantities of 1000
devices per reel for the Q package and 2000 devices per reel for the DW package.
UVLO
9.2 V / 8.4 V
MAXIMUM
DUTY CYCLE
TA
−55°C
55°C to 125°C
CDIP−16
(J)
LCCC−20
(L)
< 100%
UC1823AJ, UC1823AJ883B, UC1823AJQMLV
UC1823AL, UC1823AL883B
< 50%
UC1825AJ, UC1825AJ883B, UC1825AJQMLV
UC1825AL, UC1825AL883B, UC1825ALQMLV
PIN ASSIGNMENTS
Q OR L PACKAGES
(TOP VIEW)
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VREF
VCC
OUTB
VC
PGND
OUTA
GND
ILIM
EAOUT
CLK/LEB
NC
RT
CT
4
3 2 1 20 19
18
5
6
17
16
7
8
15
14
9 10 11 12 13
RAMP
SS
NC
ILIM
GND
INV
NI
EAOUT
CLK/LEB
RT
CT
RAMP
SS
NI
INV
NC
VREF
VCC
DW, J, OR N PACKAGES
(TOP VIEW)
NC = no connection
2
OUTB
VC
NC
PGND
OUTA
UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
TERMINAL FUNCTIONS
NAME
CLK/LEB
TERMINAL
NO.
J or DW
Q or L
4
5
I/O
DESCRIPTION
O
Output of the internal oscillator
Timing capacitor connection pin for oscillator frequency programming. The timing capacitor should
be connected to the device ground using minimal trace length.
Output of the error amplifier for compensation
Analog ground return pin
Input to the current limit comparator
Inverting input to the error amplifier
Non-inverting input to the error amplifier
High current totem pole output A of the on-chip drive stage.
High current totem pole output B of the on-chip drive stage.
Ground return pin for the output driver stage
Non-inverting input to the PWM comparator with 1.25-V internal input offset. In voltage mode
operation, this serves as the input voltage feed-forward function by using the CT ramp. In peak
current mode operation, this serves as the slope compensation input.
Timing resistor connection pin for oscillator frequency programming
Soft-start input pin which also doubles as the maximum duty cycle clamp.
Power supply pin for the output stage. This pin should be bypassed with a 0.1-μF monolithic ceramic
low ESL capacitor with minimal trace lengths.
CT
6
8
I
EAOUT
GND
ILIM
INV
NI
OUTA
OUTB
PGND
3
10
9
1
2
11
14
12
4
13
12
2
3
14
18
15
O
−
I
I
I
O
O
−
RAMP
7
9
I
RT
SS
5
8
7
10
I
I
VC
13
17
−
VCC
15
19
−
Power supply pin for the device. This pin should be bypassed with a 0.1-μF monolithic ceramic low
ESL capacitor with minimal trace lengths
VREF
16
20
O
5.1-V reference. For stability, the reference should be bypassed with a 0.1-μF monolithic ceramic
low ESL capacitor and minimal trace length to the ground plane.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted(1)
UNIT
VIN
Supply voltage,
VC, VCC
22 V
IO
Source or sink current, DC
OUTA, OUTB
0.5 A
IO
Source or sink current, pulse (0.5 μs)
OUTA, OUTB
2.2 A
INV, NI, RAMP
−0.3 V to 7 V
ILIM, SS
−0.3 V to 6 V
Analog inputs
Power ground
PGND
±0.2 V
Outputs
OUTA, OUTB limits
ICLK
Clock output current
CLK/LEB
IO(EA)
Error amplifier output current
EAOUT
5 mA
ISS
Soft-start sink current
SS
20 mA
IOSC
Oscillator charging current
RT
−5 mA
TJ
Operating virtual junction temperature range
−55°C to 150°C
Tstg
Storage temperature
−65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
tSTG
Storage temperature
Lead temperature 1,6 mm (1/16 inch) from cases for 10 seconds
(1)
PGND −0.3 V to VC +0.3 V
−5 mA
−55C°C to 150°C
−65°C to 150°C
300°C
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
3
UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
ELECTRICAL CHARACTERISTICS
TA = −55°C to 125°C for the UC1823A/UC1825A, TA = −40°C to 85°C for the UC2823x/UC2825x, TA = 0°C to 70°C for the UC3823x/UC3825x,
RT = 3.65 kΩ, CT = 1 nF, VCC = 12 V, TA = TJ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
5.05
5.1
5.15
V
REFERENCE, VREF
VO
Ouput voltage range
TJ = 25°C,
Line regulation
12 V ≤ VCC ≤ 20 V
2
15
Load regulation
1 mA ≤ IO ≤ 10 mA
5
20
Total output variation
Line, load, temperature
Temperature stability(1)
T(min) < TA < T(max)
0.2
Output noise voltage(1)
10 Hz < f < 10 kHz
50
Long term
stability(1)
Short circuit current
IO = 1 mA
TJ = 125°C,
5.03
1000 hours
mV
5.17
V
0.4
mV/°C
μVRMS
5
25
mV
30
60
90
mA
TJ = 25°C
375
400
425
kHz
RT = 6.6 kΩ, CT = 220 pF, TA = 25°C
0.9
1
1.1
MHz
VREF = 0 V
OSCILLATOR
fOSC
Initial accuracy(1)
Total variation(1)
Voltage stability
Temperature
stability(1)
Line, temperature
350
450
kHz
RT = 6.6 kΩ, CT = 220 pF,
0.85
1.15
MHz
12 V < VCC < 20 V
T(min) < TA < T(max)
High-level output voltage, clock
1%
+/−
5%
3.7
4
Low-level output voltage, clock
IOSC
0
0.2
Ramp peak
2.6
2.8
3
Ramp valley
0.7
1
1.25
Ramp valley-to-peak
1.6
1.8
2
9
10
11
mA
mV
Oscillator discharge current
RT = OPEN,
VCT = 2 V
V
ERROR AMPLIFIER
Input offset voltage
2
10
Input bias current
0.6
3
Input offset current
0.1
1
Open loop gain
1 V < VO < 4 V
60
CMRR
Common mode rejection ratio
1.5 V < VCM < 5.5 V
75
95
PSRR
Power supply rejection ratio
12 V < VCC < 20 V
85
110
IO(sink)
Output sink current
VEAOUT = 1 V
IO(src)
Output source current
VEAOUT = 4 V
High-level output voltage
IEAOUT = −0.5 mA
Low-level output voltage
IEAOUT = −1 mA
Gain bandwidth product
f = 200 kHz
Slew
(1)
4
rate(1)
Ensured by design. Not production tested.
1
μA
A
95
dB
2.5
mA
−1.3
−0.5
4.5
4.7
5
0
0.5
1
6
12
Mhz
6
9
V/μs
V
UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
ELECTRICAL CHARACTERISTICS
TA = −55°C to 125°C for the UC1823A/UC1825A, TA = −40°C to 85°C for the UC2823x/UC2825x, TA = 0°C to 70°C for the UC3823x/UC3825x,
RT = 3.65 kΩ, CT = 1 nF, VCC = 12 V, TA = TJ (unless otherwise noted)
PWM COMPARATOR
IBIAS
Bias current, RAMP
VRAMP = 0 V
−1
Minimum duty cycle
−8
μA
0%
Maximum duty cycle
85%
tLEB
Leading edge blanking time
RLEB = 2 kΩ, CLEB = 470 pF
RLEB
Leading edge blanking resistance
VCLK/LEB = 3 V
VZDC
Zero dc threshold voltage, EAOUT
VRAMP = 0 V
tDELAY
Delay-to-output time(1)
VEAOUT = 2.1 V, VILIM = 0 V to 2 V step
300
375
450
ns
8.5
10.0
11.5
kΩ
1.10
1.25
1.4
V
50
80
ns
20
μA
CURRENT LIMIT / START SEQUENCE / FAULT
ISS
Soft-start charge current
VSS
Full soft-start threshold voltage
IDSCH
Restart discharge current
ISS
Restart threshold voltage
IBIAS
ILIM bias current
ICL
Current limit threshold voltage
Overcurrent threshold voltage
Delay-to-output time, ILIM(1)
td
VSS= 2.5 V
8
14
4.3
5
100
250
350
μA
0.3
0.5
V
15
μA
0.95
1
1.05
1.14
1.2
1.26
50
80
IOUT = 20 mA
0.25
0.4
IOUT = 200 mA
1.2
2.2
IOUT = 20 mA
1.9
2.9
2
3
CL = 1 nF
20
45
UC2823B, UC2825B, UC3825B, UC3825B
16
17
9.6
VSS= 2.5 V
VILIM = 0 V to 2 V step
VILIM = 0 V to 2 V step
V
V
ns
OUTPUT
Low level output saturation voltage
Low-level
High level output saturation voltage
High-level
tr,
tf
Rise/fall time(1)
IOUT = 200 mA
V
ns
UNDERVOLTAGE LOCKOUT (UVLO)
Start threshold voltage
UC1823A, UC1825A, UC2823A, UC2825A
UC3825A, UC3825A
8.4
9.2
Stop threshold voltage
UC2823B, UC2825B, UC3825B, UC3825B
9
10
OVLO hysteresis
UC1823A, UC1825A, UC2823A, UC2825A
UC3825A, UC3825A
0.4
0.8
1.2
UC2823B, UC2825B, UC3825B, UC3825B
5
6
7
100
300
μA
28
36
mA
V
SUPPLY CURRENT
Isu
Startup current
ICC
Input current
(1)
VC = VCC = VTH(start) − 0.5 V
Ensured by design. Not production tested.
5
UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
APPLICATION INFORMATION
The oscillator of the UC3823A, UC3823B, UC3825A, and UC3825B is a saw tooth. The rising edge is governed by a current
controlled by the RT pin and value of capacitance at the CT pin (CCT). The falling edge of the sawtooth sets dead time for
the outputs. Selection of RT should be done first, based on desired maximum duty cycle. CT can then be chosen based
on the desired frequency (RT) and DMAX. The design equations are:
RT +
3V
(10 mA) ǒ1 * DMAXǓ
CT +
ǒ1.6
ǒR T
D MAXǓ
fǓ
(1)
Recommended values for RT range from 1 kΩ to 100 kΩ. Control of DMAX less than 70% is not recommended.
UDG−95102
Figure 1. Oscillator
OSCILLATOR FREQUENCY
vs
TIMING RESISTANCE
10 M
MAXIMUM DUTY CYCLE
vs
TIMING RESISTANCE
100
DMAX − Maximum Duty Cycle − %
f − Frequency − Hz
95
1M
100 k
10 k
1k
10 k
RT − Timing Resistance − W
Figure 2
6
90
85
80
75
70
100 k
1k
10 k
RT − Timing Resistance − W
Figure 3
100 k
UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
LEADING EDGE BLANKING
The UC3823A, UC2823B, UC3825A, and UC3825B perform fixed frequency pulse width modulation control. The
UC3823A, and UC3823B outputs operate together at the switching frequency and can vary from zero to some value less
than 100%. The UC3825A and UC3825B outputs are alternately controlled. During every other cycle, one output is off.
Each output then switches at one-half the oscillator frequency, varying in duty cycle from 0 to less than 50%.
To limit maximum duty cycle, the internal clock pulse blanks both outputs low during the discharge time of the oscillator.
On the falling edge of the clock, the appropriate output(s) is driven high. The end of the pulse is controlled by the PWM
comparator, current limit comparator, or the overcurrent comparator.
Normally the PWM comparator senses a ramp crossing a control voltage (error amplifier output) and terminates the pulse.
Leading edge blanking (LEB) causes the PWM comparator to be ignored for a fixed amount of time after the start of the
pulse. This allows noise inherent with switched mode power conversion to be rejected. The PWM ramp input may not
require any filtering as result of leading edge blanking.
To program a leading edge blanking (LEB) period, connect a capacitor, C, to CLK/LEB. The discharge time set by C and
the internal 10-kΩ resistor determines the blanked interval. The 10-kΩ resistor has a 10% tolerance. For more accuracy,
an external 2-kΩ 1% resistor (R) can be added, resulting in an equivalent resistance of 1.66 kΩ with a tolerance of 2.4%.
The design equation is:
t LEB + 0.5
ǒR ø 10 kWǓ
C
(2)
Values of R less than 2 kΩ should not be used.
Leading edge blanking is also applied to the current limit comparator. After LEB, if the ILIM pin exceeds the 1-V threshold,
the pulse is terminated. The overcurrent comparator, however, is not blanked. It catches catastrophic overcurrent faults
without a blanking delay. Any time the ILIM pin exceeds 1.2 V, the fault latch is set and the outputs driven low. For this
reason, some noise filtering may be required on the ILIM pin.
UDG−95105
Figure 4. Leading Edge Blanking Operational Waveforms
7
UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
UVLO, SOFT-START AND FAULT MANAGEMENT
Soft-start is programmed by a capacitor on the SS pin. At power up, SS is discharged. When SS is low, the error amplifier
output is also forced low. While the internal 9-μA source charges the SS pin, the error amplifier output follows until closed
loop regulation takes over.
Anytime ILIM exceeds 1.2 V, the fault latch is set and the output pins are driven low. The soft-start cap is then discharged
by a 250-μA current sink. No more output pulses are allowed until soft-start is fully discharged and ILIM is below 1.2 V. At
this point the fault latch resets and the chip executes a soft-start.
Should the fault latch get set during soft-start, the outputs are immediately terminated, but the soft-start capacitor does not
discharge until it has been fully charged first. This results in a controlled hiccup interval for continuous fault conditions.
UDG−95106
Figure 5. Soft-Start and Fault Waveforms
ACTIVE LOW OUTPUTS DURING UVLO
The UVLO function forces the outputs to be low and considers both VCC and VREF before allowing the chip to operate.
UDG−95108
Figure 6. Output Voltage vs Output Current
8
UDG−95106
Figure 7. Output V and I During UVLO
UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
CONTROL METHODS
Current Mode
Voltage Mode
UDG−95110
UDG−95109
.
Figure 8. Control Methods
SYNCHRONIZATION
The oscillator can be synchronized by an external pulse inserted in series with the timing capacitor. Program the free
running frequency of the oscillator to be 10% to 15% slower than the desired synchronous frequency. The pulse width
should be greater than 10 ns and less than half the discharge time of the oscillator. The rising edge of the CLK/LEB pin
can be used to generate a synchronizing pulse for other chips. Note that the CLK/LEB pin no longer accepts an incoming
synchronizing signal.
UDG−95111
Figure 9. General Oscillator Synchronization
UDG−95113
Figure 10. Two Unit Interface
UDG−95112
Figure 11. Operational Waveforms
9
UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
HIGH CURRENT OUTPUTS
Each totem pole output of the UC3823A and UC3823AB, UC3825A, and UC3825B can deliver a 2-A peak current into a
capacitive load. The output can slew a 1000-pF capacitor by 15 V in approximately 20 ns. Separate collector supply (VC)
and power ground (PGND) pins help decouple the device’s analog circuitry from the high-power gate drive noise. The use
of 3-A Schottky diodes (1N5120, USD245, or equivalent) as shown in the Figure 13 from each output to both VC and PGND
are recommended. The diodes clamp the output swing to the supply rails, necessary with any type of inductive/capacitive
load, typical of a MOSFET gate. Schottky diodes must be used because a low forward voltage drop is required. DO NOT
USE standard silicon diodes.
Although they are single-ended devices, two output drivers are available on the UC3823A and UC3823B devices. These
can be paralleled by the use of a 0.5 Ω (noninductive) resistor connected in series with each output for a combined peak
current of 4 A.
UDG−95114
Figure 12. Power MOSFET Drive Circuit
GROUND PLANES
Each output driver of these devices is capable of 2-A peak currents. Careful layout is essential for correct operation of the
chip. A ground plane must be employed. A unique section of the ground plane must be designated for high di/dt currents
associated with the output stages. This point is the power ground to which the PGND pin is connected. Power ground can
be separated from the rest of the ground plane and connected at a single point, although this is not necessary if the high
di/dt paths are well understood and accounted for. VCC should be bypassed directly to power ground with a good high
frequency capacitor. The sources of the power MOSFET should connect to power ground as should the return connection
for input power to the system and the bulk input capacitor. The output should be clamped with a high current Schottky diode
to both VCC and PGND. Nothing else should be connected to power ground.
VREF should be bypassed directly to the signal portion of the ground plane with a good high frequency capacitor. Low
ESR/ESL ceramic 1-mF capacitors are recommended for both VCC and VREF. All analog circuitry should likewise be
bypassed to the signal ground plane.
10
UC1823A, UC2823A, UC2823B,
UC3823A, UC3823B, UC1825A,
UC2825A, UC2825B, UC3825A, UC3825B
www.ti.com
SLUS334E − AUGUST 1995 − REVISED SEPTEMBER 2010
UDG−95115
Figure 13. Ground Planes Diagram
OPEN LOOP TEST CIRCUIT
This test fixture is useful for exercising many functions of this device family and measuring their specifications. As with any
wideband circuit, careful grounding and bypass procedures should be followed. The use of a ground plane is highly
recommended.
UDG−95116
Figure 14. Open Loop Test Circuit Schematic
11
PACKAGE OPTION ADDENDUM
www.ti.com
25-Oct-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
5962-87681022A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
596287681022A
UC1825AL/
883B
5962-8768102EA
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
5962-8768102EA
UC1825AJ/883B
5962-89905022A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
596289905022A
UC1823AL/
883B
5962-8990502EA
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
5962-8990502EA
UC1823AJ/883B
5962-8990502VEA
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
UC1823AJ
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
UC1823AJ
UC1823AJ883B
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
5962-8990502EA
UC1823AJ/883B
UC1823AL
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
UC1823AL
UC1823AL883B
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
596289905022A
UC1823AL/
883B
5962-8990502VE
A
UC1823AJQMLV
UC1823BJ
OBSOLETE
CDIP
J
16
TBD
Call TI
Call TI
-55 to 125
UC1823BJ883B
OBSOLETE
CDIP
J
16
TBD
Call TI
Call TI
-55 to 125
UC1823BL
OBSOLETE
LCCC
FK
20
TBD
Call TI
Call TI
-55 to 125
UC1823BL883B
OBSOLETE
LCCC
FK
20
TBD
Call TI
Call TI
0 to 70
UC1825AJ
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
UC1825AJ
UC1825AJ883B
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
5962-8768102EA
UC1825AJ/883B
UC1825AL
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
UC1825AL
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Oct-2016
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
1
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
596287681022A
UC1825AL/
883B
TBD
Call TI
Call TI
-55 to 125
59628768102XA
UC1825ALP/
883B
(4/5)
UC1825AL883B
ACTIVE
LCCC
FK
20
UC1825ALP883B
OBSOLETE
TO-92
LP
28
UC2823ADW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2823ADW
UC2823ADWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2823ADW
UC2823ADWTR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2823ADW
UC2823AN
ACTIVE
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UC2823AN
UC2823BDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2823BDW
UC2823BJ
OBSOLETE
CDIP
J
16
TBD
Call TI
Call TI
-40 to 85
UC2823BN
OBSOLETE
PDIP
N
16
TBD
Call TI
Call TI
-40 to 85
UC2823BNG4
OBSOLETE
PDIP
N
16
TBD
Call TI
Call TI
-40 to 85
UC2825ADW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2825ADW
UC2825ADWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2825ADW
UC2825ADWTR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2825ADW
UC2825ADWTRG4
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2825ADW
UC2825AN
ACTIVE
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UC2825AN
UC2825ANG4
ACTIVE
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UC2825AN
UC2825AQ
ACTIVE
PLCC
FN
20
46
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 85
UC2825AQ
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Oct-2016
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
UC2825AQG3
ACTIVE
PLCC
FN
20
46
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 85
UC2825AQ
UC2825BDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2825BDW
UC2825BDWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2825BDW
UC2825BJ
OBSOLETE
CDIP
J
16
TBD
Call TI
Call TI
-40 to 85
UC2825BN
ACTIVE
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UC2825BN
UC2825BNG4
ACTIVE
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UC2825BN
UC3823A-W
ACTIVE
WAFERSALE
YS
0
TBD
Call TI
Call TI
UC3823ADW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3823ADW
UC3823ADWTR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3823ADW
UC3823AN
ACTIVE
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UC3823AN
UC3823ANG4
ACTIVE
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UC3823AN
UC3823BDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3823BDW
UC3823BDWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3823BDW
UC3823BDWTR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3823BDW
UC3825ADW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3825ADW
UC3825ADWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3825ADW
UC3825ADWTR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3825ADW
UC3825ADWTRG4
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3825ADW
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Oct-2016
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
UC3825AN
ACTIVE
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UC3825AN
UC3825ANG4
ACTIVE
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UC3825AN
UC3825AQ
ACTIVE
PLCC
FN
20
46
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
0 to 70
UC3825AQ
UC3825BDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3825BDW
UC3825BDWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3825BDW
UC3825BDWTR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UC3825BDW
UC3825BN
ACTIVE
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UC3825BN
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 4
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Oct-2016
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF UC1823A, UC1823A-SP, UC1823B, UC1825A, UC2825A, UC3823A, UC3823B, UC3825A :
• Catalog: UC3823A, UC1823A, UC3823B, UC3825A
• Automotive: UC2825A-Q1
• Enhanced Product: UC2825A-EP
• Military: UC1823A, UC1823B, UC1825A
• Space: UC1823A-SP, UC1825A-SP
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
• Enhanced Product - Supports Defense, Aerospace and Medical Applications
• Military - QML certified for Military and Defense Applications
• Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application
Addendum-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jul-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
UC2823ADWTR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
UC2825ADWTR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
UC3823ADWTR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
UC3823BDWTR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
UC3825ADWTR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
UC3825BDWTR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jul-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
UC2823ADWTR
SOIC
DW
16
2000
367.0
367.0
38.0
UC2825ADWTR
SOIC
DW
16
2000
367.0
367.0
38.0
UC3823ADWTR
SOIC
DW
16
2000
367.0
367.0
38.0
UC3823BDWTR
SOIC
DW
16
2000
367.0
367.0
38.0
UC3825ADWTR
SOIC
DW
16
2000
367.0
367.0
38.0
UC3825BDWTR
SOIC
DW
16
2000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated