UC3717AQTR

UC3717A Stepper Motor Drive Circuit FEATURES • Full-Step, Half-Step and Micro-Step Capability • Bipolar Output Current up to 1A • Wide Range of Motor Supply Voltage 10-46V • Low Saturation Voltage with Integrated Bootstrap • Built-In Fast Recovery Commutating Diodes • Current Levels Selected in Steps or Varied Continuously • Thermal Protection with Soft Intervention DESCRIPTION The UC3717A is an improved version of the UC3717, used to switch drive the current in one winding of a bipolar stepper motor. The UC3717A has been modified to supply higher winding current, more reliable thermal protection, and improved efficiency by providing integrated bootstrap circuitry to lower recirculation saturation voltages. The diagram shown below presents the building blocks of the UC3717A. Included are an LS-TTL compatible logic input, a current sensor, a monostable, a thermal shutdown network, and an H-bridge output stage. The output stage features built-in fast recovery commutating diodes and integrated bootstrap pull up. Two UC3717As and a few external components form a complete control and drive unit for LS-TTL or micro-processor controlled stepper motor systems. The UC3717A is characterized for operation over the temperature range of 0°C to +70°C. ABSOLUTE MAXIMUM RATINGS (Note 1) Voltage Logic Supply, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V Output Supply, Vm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50V Input Voltage Logic Inputs (Pins 7, 8, 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V Analog Input (Pin 10). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC Reference Input (Pin 11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V Input Current Logic Inputs (Pins 7, 8, 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10mA Analog Inputs (Pins 10, 11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10mA Output Current (Pins 1, 15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1.2A Junction Temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C Storage Temperature Range, TS . . . . . . . . . . . . . . . . . . -55°C to +150°C BLOCK DIAGRAM 4/97 1 Note 1: All voltages are with respect to ground, Pins 4, 5, 12, 13. Currents are positive into, negative out of the specified terminal. Pin numbers refer to DIL-16 package. Consult Packaging Section of Databook for thermal limitations and considerations of package. UC3717A CONNECTION DIAGRAMS DIL-16 (TOP VIEW) J or N Package PLCC-20 (TOP VIEW) Q Package PACKAGE PIN FUNCTION FUNCTION PIN 1 N/C 2 BOUT 3 Timing 4 Vm 5 Gnd 6 N/C 7 Gnd 8 VCC 9 I1 10 Phase 11 N/C 12 I0 13 Current 14 VR 15 Gnd 16 N/C 17 Gnd 18 Vm 19 AOUT 20 Emitters ELECTRICAL CHARACTERISTICS (Refer to the test circuit, Figure 6. Vm = 36V, VCC = 5V, VR = 5V, TA = 0°C to 70°C, unless otherwise stated, TA = TJ.) PARAMETERS TEST CONDITIONS Supply Voltage, Vm (Pins 3, 14) Logic Supply Voltage, VCC (Pin 6) Logic Supply Current, ICC (Pin 6) MIN TYP UNITS 10 46 V 4.75 5.25 V IO = I 1 = 0 7 Thermal Shutdown Temperature MAX 15 mA +160 +180 °C 0.8 V 2 VCC V Logic Inputs Input Low Voltage, (Pins 7, 8, 9) Input High Voltage, (Pins 7, 8, 9) Low Voltage Input Current, (Pins 7, 8, 9) High Voltage Input Current, (Pins 7, 8, 9) VI = 0.4V, Pin 8 -100 µA VI = 0.4V, Pins 7 and 9 -400 mA 10 µA VI = 2.4V Comparators Comparator Low, Threshold Voltage (Pin 10) VR = 5V; IO = L; I1 = H 66 80 90 mV Comparator Medium, Threshold Voltage (Pin 10) VR = 5V; IO = H; I1 = L 236 250 266 mV 396 420 Comparator High, Threshold Voltage (Pin 10) VR = 5V; IO = L; I1 = L Comparator Input, Current (Pin 10) Cutoff Time, tOFF RT = 56kΩ, CT = 820pF Turn Off Delay, tD (See Figure 5) 25 436 mV ±20 µA 35 µs 2 µs Source Diode-Transistor Pair Saturation Voltage, VSAT (Pins 1, 15) Im = -0.5A, (See Figure 5) Saturation Voltage, VSAT (Pins 1, 15) Conduction Period 1.7 2.1 V Im = -0.5A, Recirculation Period 1.1 1.35 V Im = -1A, Conduction Period 2.1 2.8 V (See Figure 5) Im = -1A, Recirculation Period 1.7 Leakage Current Vm = 40V Diode Forward Voltage, VF Im = -0.5A Im = -1A 2 2.5 V 300 µA 1 1.25 V 1.3 1.7 V UC3717A (Refer to the test circuit, Figure 6. VM = 36V, VCC = 5V, VR = 5V, TA = 0°C to 70°C, unless ELECTRICAL CHARACTERISTICS (cont.) otherwise stated, TA = TJ.) PARAMETERS TEST CONDITIONS MIN TYP MAX UNITS 0.8 1.1 1.35 V 1.6 2.3 V Sink Diode-Transistor Pair Saturation Voltage, VSAT (Pins 1, 15) Im = 0.5A Im = 1A Leakage Current Vm = 40V 300 µA Diode Forward Voltage, VF Im = 0.5A 1.1 1.5 V Im = 1A 1.4 2 V Figure 1. Typical Source Saturation Voltage vs Output Current (Recirculation Period) Figure 2. Typical Source Saturation Voltage vs Output Current (Conduction Period) Figure 3. Typical Sink Saturation Voltage vs Output Current Figure 5. Typical Waveforms with MA Regulating (phase = 0) Figure 4. Typical Power Dissipation vs Output Current 3 UC3717A Figure 6. UC3717A Test Circuit FUNCTIONAL DESCRIPTION The UC3717A’s drive circuit shown in the block diagram includes the following components. saturation voltage of source transistor Q2 during recirculation, thus improving efficiency by reducing power dissipation. (1) H-bridge output stage (2) Phase polarity logic (3) Voltage divider coupled with current sensing comparators (4) Two-bit D/A current level select (5) Monostable generating fixed off-time (6) Thermal protection OUTPUT STAGE The UC3717A’s output stage consists of four Darlington power transistors and associated recirculating power diodes in a full H-bridge configuration as shown in Figure 7. Also presented, is the new added feature of integrated bootstrap pull up, which improves device performance during switched mode operation. While in switched mode, with a low level phase polarity input, Q2 is on and Q3 is being switched. At the moment Q3 turns off, winding current begins to decay through the commutating diode pulling the collector of Q3 above the supply voltage. Meanwhile, Q6 turns on pulling the base of Q2 higher than its previous value. The net effect lowers the Note: Dashed lines indicate current decay paths. Figure 7. Simplified Schematic of Output Stage 4 UC3717A FUNCTIONAL DESCRIPTION (cont.) PHASE POLARITY INPUT The UC3717A phase polarity input controls current direction in the motor winding. Built-in hysteresis insures immunity to noise, something frequently present in switched drive environments. A low level phase polarity input enables Q2 and Q3 as shown in Figure 7. During phase reversal, the active transistors are both turned off while winding current delays through the commutating diodes shown. As winding current decays to zero, the inactive transistors Q1 and Q4 turn on and charge the winding with current of the reverse direction. This delay insures noise immunity and freedom from power supply current spikes caused by overlapping drive signals. PHASE INPUT Q1, Q4 Q2, Q3 LOW OFF ON HIGH ON OFF ture to a maximum of 180C by reducing the winding current. PERFORMANCE CONSIDERATIONS In order to achieve optimum performance from the UC3717A careful attention should be given to the following items. External Components: The UC3717A requires a minimal number of external components to form a complete control and switch drive unit. However, proper selection of external components is necessary for optimum performance. The timing pin, (pin 2) is normally connected to an RC network which sets the off-time for the sink power transistor during switched mode. As shown in Figure 8, prior to switched mode, the winding current increases exponentially to a peak value. Once peak current is attained the monostable is triggered which turns off the lower sink drivers for a fixed off-time. During off-time winding current decays through the appropriate diode and source transistor. The moment off-time times out, the motor current again rises exponentially producing the ripple waveform shown. The magnitude of winding ripple is a direct function of off-time. For a given off-time TOFF, the values of RT and CT can be calculated from the expression: TOFF = 0.69RTCT with the restriction that RT should be in the range of 10100k. As shown in Figure 5, the switch frequency FS is a function of TOFF and TON. Since TON is a function of the reference voltage, sense resistor, motor supply, and winding electrical characteristics, it generally varies during different modes of operation. Thus, FS may be approximated nominally as: FS = 1⁄1.5 (TOFF). Normally, Switch Frequency Is Selected Greater than CURRENT CONTROL The voltage divider, comparators, monostable, and twobit D/A provide a means to sense winding peak current, select winding peak current, and disable the winding sink transistors. The UC3717A switched driver accomplishes current control using an algorithm referred to as "fixed off-time." When a voltage is applied across the motor winding, the current through the winding increases exponentially. The current can be sensed across an external resistor as an analog voltage proportional to instantaneous current. This voltage is normally filtered with a simple RC lowpass network to remove high frequency transients, and then compared to one of the three selectable thresholds. The two bit D/A input signal determines which one of the three thresholds is selected, corresponding to a desired winding peak current level. At the moment the sense voltage rises above the selected threshold, the UC3717A’s monostable is triggered and disables both output sink drivers for a fixed off-time. The winding current then circulates through the source transistor and appropriate diode. The reference terminal of the UC3717A provides a means of continuously adjusting the current threshold to allow microstepping. Table 1 presents the relationship between the two-bit D/A input signal and selectable current level. TABLE 1 IO 0 1 0 1 I1 0 0 1 1 CURRENT LEVEL 100% 60% 19% Current Inhibit Figure 8. A typical winding current waveform. Winding current rises exponentially to a selected peak value. The peak value is limited by switched mode operation producing a ripple in winding current. A phase polarity reversal command is given and winding current decays to zero, then increases exponentially. OVERLOAD PROTECTION The UC3717A is equipped with a new, more reliable thermal shutdown circuit which limits the junction tempera5 UC3717A FUNCTIONAL DESCRIPTION (cont.) Low-pass filter components RC CC should be selected so that all switching transients from the power transistors and commutating diodes are well smoothed, but the primary signal, which can be in the range of 1/T OFF or higher must be passed. Figure 5A shows the waveform which must be smoothed, Figure 5B presents the desired waveform that just smoothes out overshoot without radical distortion. The sense resistor should be chosen as small as practical to allow as much of the winding supply voltage to be used as overdrive to the motor winding. VRS, the voltage across the sense resistor, should not exceed 1.5V. current is excessive and must be prevented. This is accomplished with switch drive by repetitively switching the sink drivers on and off, so as to maintain an average value of current equal to the rated value. This results in a small amount of ripple in the controlled current, but the increase in step rate and performance may be considerable. Interference: Electrical noise generated by the chopping action can cause interference problems, particularly in the vicinity of magnetic storage media. With this in mind, printed circuit layouts, wire runs and decoupling must be considered. 0.01 to 0.1µF ceramic capacitors for high frequency bypass located near the drive package across V+ and ground might be very helpful. The connection and ground leads of the current sensing components should be kept as short as possible. Voltage Overdrive: In many applications, maximum speed or step rate is a desirable performance characteristic. Maximum step rate is a direct function of the time necessary to reverse winding current with each step. In response to a constant motor supply voltage, the winding current changes exponentially with time, whose shape is determined by the winding time constant and expressed as: Vm Im = R [1−EXP (−RT⁄L)] as presented in Figure 9. With rated voltage applied, the time required to reach rated current is excessive when compared with the time required with over-voltage applied, even though the time constant L/R remains constant. With over-voltage however, the final value of Half-Stepping: In half step sequence the power input to the motor alternates between one or two phases being energized. In a two phase motor the electrical phase shift between the windings is 90°. The torque developed is the vector sum of the two windings energized. Therefore when only one winding is energized the torque of the motor is reduced by approximately 30%. This causes a torque ripple and if it is necessary to compensate for this, the VR input can be used to boost the current of the single energized winding. Figure 9. With rated voltage applied, winding current does not exceed rated value, but takes L/R seconds to reach 63% of its final value - probably too long. Increased performance requires an increase in applied voltage, of overdrive, and therefore a means to limit current. The UC3717A motor driver performs this task efficiently. 6 UC3717A MOUNTING INSTRUCTIONS The θJA of the UC3717AN plastic package can be reduced by soldering the GND pins to a suitable copper area of the printed circuit board or to an external heat sink. Due to different lead frame design, θJA of the ceramic J package cannot be similarly reduced. The diagram of Figure 11 shows the maximum package power PTOT and the θJA as a function of the side " l " of two equal square copper areas having a thickness of 35µ (see Figure 10). 12. The input can be controlled by a microprocessor, TTL, LS, or CMOS logic. The timing diagram in Figure 13 shows the required signal input for a two phase, full step stepping sequence. Figure 14 shows the required input signal for a one phase-two phase stepping sequence called half-stepping. The circuit of Figure 15 provides the signal shown in Figure 13, and in conjunction with the circuit shown in Figure 12 will implement a pulse-to-step two phase, full step, bi-directional motor drive. Figure 10. Example of P.C. Board Copper Area which is used as Heatsink. During soldering the pins’ temperature must not exceed 260°C and the soldering time must not be longer than 12 seconds. The printed circuit copper area must be connected to electrical ground. Figure 12. Typical Chopper Drive for a Two Phase Permanent Magnet Motor. The schematic of Figure 16 shows a pulse to half step circuit generating the signal shown in Figure 14. Care has been taken to change the phase signal the same time the current inhibit is applied. This will allow the current to decay faster and therefore enhance the motor performance at high step rates. Figure 11. Maximum Package Power and Junction to Ambient Thermal Resistance vs Side "l". APPLICATIONS A typical chopper drive for a two phase bipolar permanent magnet or hybrid stepping motor is shown in Figure 7 UC3717A Figure 13. Phase Input Signal for Two Phase Full Step Drive (4 Step Sequence) Figure 14. Phase and Current-Inhibit Signal for Half-Stepping (8 Step Sequence) Figure 15. Full Step, Bi-directional Two Phase Drive Logic Figure 16. Half-Step, Bi-directional Drive Logic UNITRODE CORPORATION 7 CONTINENTAL BLVD. • MERRIMACK, NH 03054 TEL. (603) 424-2410 • FAX (603) 424-3460 8 PACKAGE OPTION ADDENDUM www.ti.com 13-Aug-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) UC3717AN ACTIVE PDIP N 16 25 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 UC3717AN UC3717ANG4 ACTIVE PDIP N 16 25 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 UC3717AN (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of