Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
UCC2751x Single-Channel, High-Speed, Low-Side Gate Driver (Based On CMOS Input
Threshold With 4-A Peak Source and 4-A Peak Sink)
1 Features
3 Description
•
The UCC27518 and UCC27519 single-channel, highspeed, low-side gate driver device can effectively
drive MOSFET and IGBT power switches. Using a
design that inherently minimizes shoot-through
current, UCC27518 and UCC27519 can source and
sink high, peak-current pulses into capacitive loads
offering rail-to-rail drive capability and extremely small
propagation delay typically 17 ns.
1
•
•
•
•
•
•
•
•
•
•
•
•
•
Low-Cost, Gate-Driver Device Offering Superior
Replacement of NPN and PNP Discrete Solutions
Pin-to-Pin Compatible With TI's TPS2828 and
TPS2829 devices
4-A Peak Source and 4-A Peak Sink Symmetrical
Drive
Fast Propagation Delays (17-ns Typical)
Fast Rise and Fall Times (8-ns and 7-ns Typical)
4.5-V to 18-V Single Supply Range
Outputs Held Low During VDD UVLO (Ensures
Glitch-Free Operation at Power Up and Power
Down)
CMOS Input Logic Threshold (Function of Supply
Voltage With Hysteresis)
Hysteretic Logic Thresholds for High Noise
Immunity
EN Pin for Enable Function (Allowed to Be No
Connect)
Output Held Low when Input Pins are Floating
Input Pin Absolute Maximum Voltage Levels Not
Restricted by VDD Pin Bias Supply Voltage
Operating Temperature Range of –40°C to 140°C
5-Pin DBV Package (SOT-23)
The UCC27518 and UCC27519 provide 4-A source,
4-A sink (symmetrical drive) peak-drive current
capability at VDD = 12 V.
The UCC27518 and UCC27519 are designed to
operate over a wide VDD range of 4.5 V to 18 V and
a wide temperature range of –40°C to 140°C. Internal
under voltage lockout (UVLO) circuitry on the VDD
pin holds output low outside VDD operating range.
The capability to operate at low voltage levels such
as below 5 V, along with best-in-class switching
characteristics, is especially suited for driving
emerging wide band-gap power switching devices
such as GaN power semiconductor devices.
Device Information(1)
PART NUMBER
UCC27518
UCC27519
•
•
BODY SIZE (NOM)
SOT-23 (5)
2.90 mm × 1.60 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
2 Applications
•
•
•
PACKAGE
Switched-Mode Power Supplies
DC-DC Converters
Companion Gate Driver Devices for Digital Power
Controllers
Solar Power, Motor Control, UPS
Gate Driver for Emerging Wide Band-Gap Power
Devices (Such as GaN)
Typical Application Diagram
UCC27518/19
EN
1
EN
2
GND
3
IN+/IN-
VDD
4.5 V to 18 V
V+
5
C1
Q1
R1
IN
OUT
4
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Description (continued).........................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
8.1
8.2
8.3
8.4
8.5
8.6
8.7
9
1
1
1
2
3
3
4
5
Absolute Maximum Ratings ...................................... 5
ESD Ratings.............................................................. 5
Recommended Operating Conditions....................... 5
Thermal Information .................................................. 5
Electrical Characteristics........................................... 6
Switching Characteristics .......................................... 7
Typical Characteristics ............................................ 10
Detailed Description ............................................ 13
9.1 Overview ................................................................. 13
9.2 Functional Block Diagrams ..................................... 14
9.3 Feature Description................................................. 14
9.4 Device Functional Modes........................................ 17
10 Application and Implementation........................ 18
10.1 Application Information.......................................... 18
10.2 Typical Application ................................................ 18
11 Power Supply Recommendations ..................... 22
12 Layout................................................................... 22
12.1
12.2
12.3
12.4
Layout Guidelines .................................................
Layout Example ....................................................
Thermal Considerations ........................................
Power Dissipation .................................................
22
23
23
24
13 Device and Documentation Support ................. 25
13.1
13.2
13.3
13.4
Related Links ........................................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
25
25
25
25
14 Mechanical, Packaging, and Orderable
Information ........................................................... 25
4 Revision History
Changes from Original (May 2012) to Revision A
•
2
Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
5 Description (continued)
The input pin threshold of the UCC27518 and UCC27519 are based on CMOS logic where the threshold voltage
is a function of the VDD supply voltage. Typically Input High Threshold (VIN-H) is 55% VDD and Input Low
Threshold (VIN-L) is 39% VDD. Wide hysteresis (16% VDD typically) between the high and low thresholds offers
excellent noise immunity and lets users introduce delays using RC circuits between the input PWM signal and
the INx pin of the device.
The UCC27518 and UCC27519 also feature a floatable enable function on the EN pin. The EN pin can be left in
a no connect condition, which allows pin-to-pin compatibility between the UCC27518, UCC27519 and the
TPS2828, TPS2829, respectively. The thresholds of the EN pin is a fixed voltage threshold and does not vary
based on VDD pin bias voltage. Typically, the Enable High Threshold (VEN-H) is 2.1 V and Enable Low Threshold
(VEN-L) is 1.25 V.
6 Device Comparison Table
The UCC2751x family of gate driver products (Table 1) represent TI's latest generation of single-channel, lowside high-speed gate driver devices featuring high-source/sink current capability, industry best-in-class switching
characteristics and a host of other features (Table 2) all of which combine to ensure efficient, robust and reliable
operation in high-frequency switching power circuits.
Table 1. UCC2751x Product Family Summary
PART NUMBER
UCC27511DBV (1)
SOT-23, 6 pin
UCC27512DRS (1)
3 mm x 3 mm WSON, 6 pin
(1)
3 mm x 3 mm WSON, 6 pin
UCC27516DRS
(1)
PACKAGE
UCC27517DBV (1)
SOT-23, 5 pin
UCC27518DBV
SOT-23, 5 pin
UCC27519DBV
SOT-23, 5 pin
PEAK CURRENT
(SOURCE/SINK)
4-A/8-A
(Asymmetrical Drive)
4-A/4-A
(Symmetrical Drive)
INPUT THRESHOLD LOGIC
CMOS/TTL-Compatible
(low voltage, independent of VDD
bias voltage)
CMOS
(follows VDD bias voltage)
Visit www.ti.com for the latest product datasheet.
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
3
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
7 Pin Configuration and Functions
UCC27518
SOT-23 DBV
(Top View)
EN
GND
IN-
1
UCC27519
SOT-23 DBV
(Top View)
5
VDD
EN
1
GND
2
IN+
3
5
VDD
4
OUT
2
3
4
OUT
Pin Functions
PIN
NO.
NAME
I/O
DESCRIPTION
Enable input: (EN biased LOW disables output regardless of Input state, EN biased
high or floating enables output, EN is allowed to float hence it is pin-to-pin compatible
with TPS282X N/C pin)
1
EN
I
2
GND
—
IN–
I
Input: Inverting input in the UCC27518, output held LOW if IN– is unbiased or floating
IN+
I
Input: Noninverting input in the UCC27519, output held LOW if IN+ is unbiased or
floating
4
OUT
O
Sourcing and sinking current output of driver
5
VDD
I
Supply input
3
4
Submit Documentation Feedback
Ground: All signals referenced to this pin
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
8 Specifications
8.1 Absolute Maximum Ratings (1) (2) (3)
over operating free-air temperature range (unless otherwise noted)
Supply voltage
VDD
OUT voltage
Output continuous current
IOUT_DC (source/sink)
Output pulsed current (0.5 µs)
IOUT_pulsed(source/sink)
MIN
MAX
–0.3
20
–0.3
VDD + 0.3
–0.3
20
–40
150
Soldering, 10 sec.
300
Reflow
260
Storage temperature, Tstg
(2)
(3)
(4)
A
4
Operating virtual junction temperature, TJ
(1)
V
0.3
IN+, IN- (4), EN
Lead temperature
UNIT
–65
V
°C
150
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to GND unless otherwise noted. Currents are positive into, negative out of the specified terminal. See
Packaging Section of the data sheet for thermal limitations and considerations of packages.
These devices are sensitive to electrostatic discharge; follow proper device handling procedures.
Maximum voltage on input pins is not restricted by the voltage on the VDD pin.
8.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±4000
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
±1000
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
8.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
Supply voltage range, VDD
4.5
12
18
V
Operating junction temperature range
–40
140
°C
0
18
V
Input voltage, (IN+ and IN–) and Enable (EN)
MAX
UNIT
8.4 Thermal Information
THERMAL METRIC
RθJA
UCC27518
UCC27519
SOT-23 DBV
SOT-23 DBV (1)
5 PINS
5 PINS
217.6
217.6
Junction-to-ambient thermal resistance (1)
(1)
RθJC(top)
Junction-to-case (top) thermal resistance
85.8
85.8
RθJB
Junction-to-board thermal resistance (1)
44.0
44.0
ψJT
Junction-to-top characterization parameter (1)
4.0
4.0
ψJB
Junction-to-board characterization parameter (1)
43.2
43.2
(1)
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
5
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
8.5 Electrical Characteristics
VDD = 12 V, TA = TJ = -40 °C to 140 °C, 1-µF capacitor from VDD to GND. Currents are positive into, negative out of the
specified terminal.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
IN+ = VDD (UCC27519),
IN- = GND (UCC27518)
51
85
123
IN+ = GND (UCC27519),
IN- = VDD (UCC27518)
51
70
103
TA = 25 °C
3.85
4.20
4.57
TA = -40 °C to 140°C
3.80
4.20
4.67
UNIT
BIAS CURRENTS
IDD(off)
Startup current
VDD = 3.4 V
µA
UNDERVOLTAGE LOCKOUT (UVLO)
VON
Supply start threshold
VOFF
Minimum operating
voltage after supply start
3.45
3.9
4.35
VDD_H
Supply voltage hysteresis
0.19
0.3
0.45
55
62
V
INPUTS (IN+, IN–)
VIN_H
Input signal high threshold
VIN_L
Input signal low threshold
VIN_HYS
Input signal hysteresis
VIN_H
Input signal high threshold
VIN_L
Input signal low threshold
VIN_HYS
Input signal hysteresis
16
VIN_H
Input signal high threshold
55
VIN_L
Input signal low threshold
VIN_HYS
Input signal hysteresis
VDD = 4.5 V
31
39
16
55
VDD = 12 V
31
VDD = 18 V
35
59
39
%VDD
58
38
17
ENABLE (EN)
VEN_H
Enable signal high
threshold
VEN_L
Enable signal low
threshold
VEN_HYS
Enable hysteresis
2.1
VDD = 12 V
1.00
2.3
V
1.25
0.86
SOURCE/SINK CURRENT
ISRC/SNK
Source/sink peak
current (1)
CLOAD = 0.22 µF, FSW = 1 kHz
-4/+4
A
OUTPUTS (OUT)
VDD-VOH
VOL
ROH
ROL
(1)
(2)
6
High output voltage
Low output voltage
Output pullup resistance (2)
Output pulldown
resistance
VDD = 12 V
IOUT = -10 mA
50
90
VDD = 4.5 V
IOUT = -10 mA
60
130
VDD = 12
IOUT = 10 mA
5
11
VDD = 4.5 V
IOUT = 10 mA
6
12
VDD = 12 V
IOUT = -10 mA
5.0
7.5
VDD = 4.5 V
IOUT = -10 mA
5.0
11.0
VDD = 12 V
IOUT = 10 mA
0.5
1.0
VDD = 4.5 V
IOUT = 10 mA
0.6
1.2
mV
Ω
Ensured by Design.
ROH represents on-resistance of P-Channel MOSFET in pullup structure of the UCC27518 and UCC27519's output stage.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
8.6 Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
(1)
MIN
TYP
MAX
tR
Rise time
CLOAD = 1.8 nF
8
12
tF
Fall time (1)
CLOAD = 1.8 nF
7
11
tD1
IN+ to output propagation delay (1)
VDD = 10 V
7-V input pulse, CLOAD = 1.8 nF
6
17
25
tD2
IN- to output propagation delay (1)
VDD = 10 V
7-V input pulse, CLOAD = 1.8 nF
6
17
24
tD3
EN to output high propagation
delay (1)
CLOAD = 1.8 nF, 5-V enable pulse
4
12
16
tD4
EN to output low propagation
delay (1)
CLOAD = 1.8 nF, 5-V enable pulse
4
12
19
(1)
UNIT
ns
See timing diagrams in Figure 1, Figure 2, Figure 3, and Figure 4.
High
Input
Low
High
Enable
Low
90%
Output
10%
tD1
tD1
UDG-11219
(In+ Pin, UCC27519)
Figure 1. Noninverting Configuration
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
7
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
High
Input
Low
High
Enable
Low
90%
Output
10%
tD2
tD2
UDG-11220
(In– Pin, UCC27518)
Figure 2. Inverting Configuration
High
Input
Low
High
Enable
Low
90%
Output
10%
tD3
tD4
UDG-11217
(Noninverting Configuration, UCC27519)
Figure 3. Enable and Disable Function
8
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
High
Input
Low
High
Enable
Low
90%
Output
10%
tD3
tD4
UDG-11218
(Inverting Configuration, UCC27518)
Figure 4. Enable and Disable Function
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
9
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
8.7 Typical Characteristics
0.12
3.5
0.1
IDD (mA)
Startup Current (mA)
0.11
4
IN+=Low,IN−=Low
IN+=High, IN−=Low
0.09
0.08
0.07
VDD = 3.4 V
0
50
Temperature (°C)
100
2
−50
150
100
150
G013
4.6
IN+=Low,IN−=Low
IN+=High, IN−=Low
UVLO Rising
UVLO Falling
4.4
0.4
UVLO Threshold (V)
Operating Supply Current (mA)
50
Temperature (°C)
Figure 6. Operating Supply Current vs Temperature (Output
Switching)
0.5
0.3
0.2
4.2
4
3.8
VDD = 12 V
0.1
−50
0
50
Temperature (°C)
100
3.6
−50
150
50
Temperature (°C)
100
150
G003
Figure 8. UVLO Threshold Voltage vs Temperature
70
8
VDD = 12V
RoH
Output Pull−Up Resistance (Ω)
Turn−On
Turn−Off
50
30
−50
0
G002
Figure 7. Supply Current vs Temperature (Output In DC
On/Off Condition)
Input Threshold Voltage / VDD (%)
0
G001
Figure 5. Start-Up Current vs Temperature
0
50
Temperature (°C)
100
Submit Documentation Feedback
150
7
6
5
VDD = 12 V
Iout = 10 mA
4
−50
0
G001
Figure 9. Input Threshold vs Temperature
10
VDD = 12 V
CLoad = 500 pF
fsw = 500 kHz
2.5
0.06
0.05
−50
3
50
Temperature (°C)
100
150
G004
Figure 10. Output Pullup Resistance vs Temperature
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
Typical Characteristics (continued)
1
8
VDD = 12 V
CLoad = 1.8 nF
0.8
7
Rise Time (ns)
Pull−Down Resistance (Ω)
ROL
0.6
0.4
6
5
0.2
−50
0
50
Temperature (°C)
100
4
−50
150
Figure 11. Output Pulldown Resistance vs Temperature
100
150
G000
20
VDD = 12 V
CLoad = 1.8 nF
Propagation Delay (ns)
8
7
6
−50
0
50
Temperature (°C)
100
VDD = 10V
Turn−On
Turn−Off
9
Fall Time (ns)
50
Temperature (°C)
Figure 12. Rise Time vs Temperature
10
18
16
14
−50
150
0
G000
Figure 13. Fall Time vs Temperature
50
Temperature (°C)
100
150
G002
Figure 14. Input To Output Propagation Delay vs
Temperature
20
20
VDD=4.5V
VDD=12V
VDD=15V
18
16
14
Rise Time (ns)
Supply Current (mA)
0
G000
12
10
8
6
15
10
4
CLoad = 1.8 nF
2
0
0
100
200
300
400
Frequency (kHz)
500
600
700
5
0
4
G010
Figure 15. Operating Supply Current vs Frequency
8
12
Supply Voltage (V)
16
20
G008
Figure 16. Rise Time vs Supply Voltage
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
11
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
Typical Characteristics (continued)
10
Fall Time (ns)
8
6
4
2
0
4
8
12
Supply Voltage (V)
16
20
G009
Figure 17. Fall Time vs Supply Voltage
12
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
9 Detailed Description
9.1 Overview
The UCC2751x single-channel, high-speed, low-side gate-driver device is capable of effectively driving MOSFET
and IGBT power switches. Using a design that inherently minimizes shoot-through current, the UCC2751x device
is capable of sourcing and sinking high peak-current pulses into capacitive loads offering rail-to- rail drive
capability and extremely small propagation delay of 13 ns (typical).
The UCC2751x device provides 4-A source, 4-A sink (symmetrical drive) peak-drive current capability. The
device is designed to operate over a wide VDD range of 4.5 to 18 V, and a wide temperature range of -40°C to
140°C. Internal undervoltage lockout (UVLO) circuitry on the VDD pin holds the output low outside VDD operating
range. The capability to operate at low voltage levels, such as below 5 V, along with best-in-class switching
characteristics, is especially suited for driving emerging wide band-gap power-switching devices such as GaN
power-semiconductor devices.
The UCC27518 device follows an inverting logic between the input and output, while the UCC27519 device
follows noninverting logic. The input pins of the devices are based on what is known as CMOS input threshold
logic. In CMOS input logic, the threshold voltage level is a function of the bias voltage on the VDD pin of the
device. This offers the benefits of higher noise immunity due to the higher threshold voltage (compared to logic
level input thresholds), as well as the ability to accept slow dV/dt input signals for manipulating the propagation
delay between the PWM controller signal and the gate driver output. For system robustness, internal pull-up and
pull-down resistors on the input pins ensure that outputs are held low when the input pins are in floating
condition.
Table 2. UCC2751x Family of Features and Benefits
FEATURE
BENEFIT
High Source/Sink Current Capability
4 A/8 A (Asymmetrical) – UCC27511/2
4 A/4 A (Symmetrical) – UCC27516/7
High current capability offers flexibility in employing UCC2751x
family of devices to drive a variety of power switching devices at
varying speeds
Best-in-class 13-ns (typ) Propagation delay
Extremely low pulse transmission distortion
Expanded VDD Operating range of 4.5 V to 18 V
Flexibility in system design
Low VDD operation ensures compatibility with emerging wide bandgap power devices such as GaN
Expanded Operating Temperature range of -40 °C to 140 °C
(See Electrical Characteristics table)
VDD UVLO Protection
Outputs are held low in UVLO condition, which ensures predictable,
glitch-free operation at power-up and power-down
Outputs held low when input pins (INx) in floating condition
Safety feature, especially useful in passing abnormal condition tests
during safety certification
Ability of input pins (and enable pin in UCC2751x) to handle voltage
levels not restricted by VDD pin bias voltage
System simplification, especially related to auxiliary bias supply
architecture
Split output structure in UCC27511 (OUTH, OUTL)
Allows independent optimization of turnon and turnoff speeds
Strong sink current (8 A) and low pull-down impedance (0.375 Ω) in
UCC27511/2
High immunity to C x dV/dt Miller turnon events
CMOS/TTL compatible input threshold logic with wide hysteresis in
UCC27511/2/6/7
Enhanced noise immunity, while retaining compatibility with
microcontroller logic level input signals (3.3 V, 5 V) optimized for
digital power
CMOS input threshold logic in UCC2751x (VIN_H – 70% VDD,
VIN_L – 30% VDD)
Well suited for slow input voltage signals, with flexibility to program
delay circuits (RCD)
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
13
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
9.2 Functional Block Diagrams
VDD
UCC27518
200 kW
EN
VDD
1
VDD
5
VDD
4
OUT
VDD
200 kW
IN-
3
VDD
GND
2
UVLO
Figure 18. UCC27518 Functional Block Diagram
VDD
UCC27519
200 kW
EN
VDD
1
5
VDD
4
OUT
VDD
IN+
3
230 kW
GND
2
VDD
UVLO
Figure 19. UCC27519 Functional Block Diagram
9.3 Feature Description
9.3.1 VDD and Undervoltage Lockout
The UCC2751x devices have internal Under Voltage LockOut (UVLO) protection feature on the VDD pin supply
circuit blocks. Whenever the driver is in UVLO condition (i.e. when VDD voltage less than VON during power up
and when VDD voltage is less than VOFF during power down), this circuit holds all outputs LOW, regardless of the
status of the inputs. The UVLO is typically 4.2 V with 300-mV typical hysteresis. This hysteresis helps prevent
chatter when low VDD supply voltages have noise from the power supply and also when there are droops in the
VDD bias voltage when the system commences switching and there is a sudden increase in IDD. The capability to
operate at low voltage levels such as below 5 V, along with best-in-class switching characteristics, is especially
suited for driving emerging GaN wide bandgap power semiconductor devices.
For example, at power up, the UCC2751x driver output remains LOW until the VDD voltage reaches the UVLO
threshold. The magnitude of the OUT signal rises with VDD until steady-state VDD is reached. In the noninverting
device (PWM signal applied to IN+ pin) shown below, the output remains LOW until the UVLO threshold is
reached, and then the output is in-phase with the input. In the inverting device (PWM signal applied to IN- pin)
shown below the output remains LOW until the UVLO threshold is reached, and then the output is out-phase with
the input.
14
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
Feature Description (continued)
Since the driver draws current from the VDD pin to bias all internal circuits, for the best high-speed circuit
performance, two VDD bypass capacitors are recommended to prevent noise problems. The use of surface
mount components is highly recommended. A 0.1-μF ceramic capacitor should be located as close as possible to
the VDD to GND pins of the gate driver. In addition, a larger capacitor (such as 1 μF) with relatively low ESR
should be connected in parallel and close proximity, in order to help deliver the high-current peaks required by
the load. The parallel combination of capacitors should present a low impedance characteristic for the expected
current levels and switching frequencies in the application.
VDD
VDD Threshold
VDD Threshold
IN+
IN -
IN+
IN-
OUT
OUT
Figure 20. Power-Up (Noninverting Drive)
Figure 21. Power-Up (Inverting Drive)
9.3.2 Operating Supply Current
The UCC27518 and UCC27519 features very low quiescent IDD currents. The typical operating supply current in
Under Voltage LockOut (UVLO) state and fully-on state (under static and switching conditions) are summarized
in Figure 5, Figure 6 and Figure 7. The IDD current when the device is fully on and outputs are in a static state
(DC high or DC low, refer Figure 7) represents lowest quiescent IDD current when all the internal logic circuits of
the device are fully operational. The total supply current is the sum of the quiescent IDD current, the average IOUT
current due to switching and finally any current related to pull-up resistors on the unused input pin. For example
when the inverting input pin is pulled low additional current is drawn from VDD supply through the pull-up
resistors (refer to Pin Configuration and Functions for the device Block Diagram). Knowing the operating
frequency (fSW) and the MOSFET gate (QG) charge at the drive voltage being used, the average IOUT current can
be calculated as product of QG and fSW.
A complete characterization of the IDD current as a function of switching frequency at different VDD bias
voltages under 1.8-nF switching load is provided in Figure 15. The strikingly linear variation and close correlation
with theoretical value of average IOUT indicates negligible shoot-through inside the gate-driver device attesting to
its high-speed characteristics.
9.3.3 Input Stage
The input pins of UCC27518 and UCC27519 are based on CMOS input logic where the threshold voltage level is
a function of the bias voltage applied on the VDD pin. Typically, the Input High Threshold (V_INH) is 55% VDD
and Input Low Threshold (VIN_L) is 39% VDD. Hysteresis (typically 19% VDD) available on the input threshold
offers noise immunity. With high VDD voltages resulting in wide hysteresis, slow dV/dt input signals are
acceptable in the INx pins and RC circuits can be inserted between the input PWM signal and the INx pins of
UCC2751x, to program a delay between the input signal and output transition.
9.3.4 Enable Function
The Enable pin is based on a noninverting configuration (active high operation). When EN pin is driven high the
output is enabled and when EN pin is driven low the output is disabled. Unlike input pin, the enable pin threshold
is based on a TTL/CMOS compatible input threshold logic that does not vary with the supply voltage. Typically,
the Enable High Threshold (V_ENH) is 2.1 V and Enable Low Threshold (VEN_L) is 1.25 V. Thus the EN pin can
be effectively controlled using logic signals from 3.3-V and 5-V microcontrollers. The EN pin is internally pulled
up to VDD using pull-up resistor as a result of which the output of the device is enabled in the default state.
Hence the EN pin can be left floating or Not Connected (N/C) for standard operation, when enable feature is not
needed. Essentially, this allows the UCC27518/19 devices to be pin-to-pin compatible with TI’s previous
generation drivers TPS2828/9 respectively, where pins #1 is N/C pin.
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
15
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
Feature Description (continued)
9.3.5 Output Stage
The UCC27518 and UCC27519 are capable of delivering 4-A source, 4-A sink (symmetrical drive) at VDD = 12
V. The output stage of the UCC27518 and UCC27519 devices are illustrated in Figure 22. The UCC27518 and
UCC27519 devices features a unique architecture on the output stage which delivers the highest peak source
current when it is most needed during the Miller plateau region of the power switch turnon transition (when the
power switch drain/collector voltage experiences dV/dt). The device output stage features a hybrid pull-up
structure using a parallel arrangement of N-Channel and P-Channel MOSFET devices. By turning on the NChannel MOSFET during a narrow instant when the output changes state from low to high, the gate-driver device
is able to deliver a brief boost in the peak-sourcing current enabling fast turn on.
VCC
ROH
RNMOS, Pull Up
Input Signal Anti ShootThrough
Circuitry
Gate
Voltage
Boost
OUT
Narrow Pulse at
each Turn On
ROL
Figure 22. UCC2751x Gate Driver Output Structure
The ROH parameter (see Electrical Characteristics) is a DC measurement and it is representative of the onresistance of the P-Channel device only, since the N-Channel device is turned on only during output change of
state from low to high. Thus the effective resistance of the hybrid pull-up stage is much lower than what is
represented by ROH parameter. The pull-down structure is composed of a N-Channel MOSFET only. The ROL
parameter (see Electrical Characteristics), which is also a DC measurement, is representative of true impedance
of the pull-down stage in the device. In UCC27518 and UCC27519, the effective resistance of the hybrid pull-up
structure is approximately 1.4 x ROL.
The driver output voltage swings between VDD and GND providing rail-to-rail operation, thanks to the MOS
output stage which delivers very low dropout. The presence of the MOSFET body diodes also offers low
impedance to switching overshoots and undershoots. This means that in many cases, external Schottky diode
clamps may be eliminated. The outputs of these drivers are designed to withstand 500-mA reverse current
without either damage to the device or logic malfunction.
9.3.6 Low Propagation Delays
The UCC27518 and UCC27519 driver device features best-in-class input-to-output propagation delay of 17 ns
(typ) at VDD = 12 V. This promises the lowest level of pulse transmission distortion available from industry
standard gate driver devices for high-frequency switching applications. As seen in Figure 14, there is very little
variation of the propagation delay with temperature and supply voltage as well, offering typically less than 20-ns
propagation delays across the entire range of application conditions.
16
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
9.4 Device Functional Modes
Table 3. Device Logic Table
EN
UCC27519
OUT PIN
IN+ PIN
OUT PIN
L
H
L
L
H
H
L
H
H
L
Any
L
Any
L
Any
x (1)
L
x (1)
L
x (1)
L
H
L
L
(1)
H
L
H
H
H
x
(1)
UCC27518
IN– PIN
x = Floating Condition
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
17
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
10 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
High-current gate driver devices are required in switching power applications for a variety of reasons. In order to
effect fast switching of power devices and reduce associated switching power losses, a powerful gate driver can
be employed between the PWM output of controllers and the gates of the power semiconductor devices. Gate
drivers also find other needs such as minimizing the effect of high-frequency switching noise by locating the highcurrent driver physically close to the power switch, driving gate-drive transformers and controlling floating powerdevice gates, reducing power dissipation and thermal stress in controllers by moving gate charge power losses
into itself. Finally, emerging wide band-gap power device technologies such as GaN based switches, which are
capable of supporting very high switching frequency operation, are driving very special requirements in terms of
gate drive capability. These requirements include operation at low VDD voltages (5 V or lower), low propagation
delays and availability in compact, low-inductance packages with good thermal capability. In summary gate-driver
devices are extremely important components in switching power combining benefits of high-performance, low
cost, component count and board space reduction and simplified system design.
10.2 Typical Application
UCC27518/19
EN
1
EN
2
GND
3
IN+/IN-
VDD
4.5 V to 18 V
V+
5
C1
Q1
R1
IN
OUT
4
Figure 23. Typical Application Diagram
10.2.1 Design Requirements
When selecting the proper gate driver device for an end application, some design considerations must be
evaluated first to make the most appropriate selection. Among these considerations are input-to-output
configuration, the input threshold type, bias supply voltage levels, peak source and sink currents, availability of
independent enable and disable functions, propagation delay, power dissipation, and package type.
Table 4. Design Parameters
18
Design Parameter
Example Value
Input-to-Output Logic
Noninverting
Input Threshold Type
CMOS type
VDD Bias Supply Voltage
10 V (Minimum), 13 V (Nominal), 15 V (Peak)
Peak Source and Sink Currents
Minimum 3 A Source, Minimum 3 A Sink
Enable and Disable Function
Yes, Needed
Propagation Delay
Maximum 40 ns or less
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
10.2.2 Detailed Design Procedure
10.2.2.1 Input-to-Output Logic
The design must specify which type of input-to-output configuration should be used. If turning on the power
MOSFET or IGBT when the input signal is in high state is preferred, then the noninverting configuration must be
selected. If turning off the power MOSFET or IGBT when the input signal is in high state is preferred, the
inverting configuration must be chosen. The UCC27518 and UCC27519 devices follow inverting and noninverting
logic, respectively.
10.2.2.2 Input Threshold Type
The type of input voltage threshold determines the type of controller used with the gate driver device. The
UCC27518 and UCC27519 devices feature CMOS input threshold logic, with wide hysteresis. In CMOS input
threshold logic, the threshold voltage level is a function of the bias voltage on the VDD pin of the device. The
typical high threshold is 55% of VDD supply voltage, and the typical low threshold is 39% of VDD supply voltage at
VDD=12V. There is built-in hysteresis, which is typically 16% of VDD supply voltage. See Electrical Characteristics
for the actual input threshold voltage levels and hysteresis specifications for the UCC27518 and UCC27519
devices at different VDD bias levels.
In most applications, the absolute value of the threshold voltage offered by the CMOS logic will be higher
(eg.VINH = 5.5 V if VDD = 10 V) than what is offered by logic level threshold devices. This offers the following
benefits:
• Better noise immunity due to the higher threshold level desirable in high power systems.
• Ability to accept slow dV/dt input signals, which allows designers to use RCD circuits on the input pin to
program propagation delays in the application, as shown in Figure 24.
D
PWM Input
VH
R del
INx
OUTx
VL
PWM Input Signal
C del
VIN
Driver Output
Figure 24. Using RCD Circuits
æ VL - VIN _ H
ö
t del = -RdelCdel ´ In ç
+ 1÷
ç V -V
÷
H
L
è
ø
(1)
As a result of the CMOS input logic, the UCC27518 and UCC27519 devices cannot be driven directly by logic
level control signals from microcontrollers, digital power controllers, or DSPs. The UCC27518 and UCC27519 are
ideally suited for being driven by analog controllers driven by the same VDD voltage as the gate driver devices.
10.2.2.3 VDD Bias Supply Voltage
The bias supply voltage to be applied to the VDD pin of the device should never exceed the values listed in
Recommended Operating Conditions. However, different power switches demand different voltage levels to be
applied at the gate terminals for effective turn on and turnoff. With certain power switches, a positive gate voltage
may be required for turn on, and a negative gate voltage may be required for turnoff, in which case the VDD bias
supply equals the voltage differential. With a wide operating range from 4.5 V to 18 V, the UCC27518 and
UCC27519 devices can be used to drive a variety of power switches, such as Si MOSFETs (for example, VGS =
4.5 V, 10 V, 12 V), IGBTs (VGE = 15 V, 18 V), and wide-band gap power semiconductors (such as GaN, certain
types of which allow no higher than 6 V to be applied to the gate terminals).
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
19
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
10.2.2.4 Peak Source and Sink Currents
Generally, the switching speed of the power switch during turn on and turnoff should be as fast as possible, to
minimize switching power losses. The gate driver device must be able to provide the required peak current for
achieving the targeted switching speeds for the targeted power MOSFET. Using the example of a power
MOSFET, the system requirement for the switching speed is typically described in terms of the slew rate of the
drain-to-source voltage of the power MOSFET (such as dVDS/dt).
For example, the system requirement might state that a SPP20N60C3 power MOSFET must be turned-on with a
dVDS/dt of 20V/ns or higher under a DC bus voltage of 400 V in a continuous-conduction-mode (CCM) boost
PFC-converter application. This type of application is an inductive, hard-switching application, and reducing
switching power losses is critical. This requirement means that the entire drain-to-source voltage swing during
power MOSFET turnon event (from 400 V in the OFF state to VDS(on) in on state) must be completed in
approximately 20 ns or less.
When the drain-to-source voltage swing occurs, the Miller charge of the power MOSFET (QGD parameter in
SPP20N60C3 power MOSFET data sheet = 33 nC typical) is supplied by the peak current of gate driver.
According to the power MOSFET inductive switching mechanism, the gate-to-source voltage of the power
MOSFET at this time is the Miller plateau voltage, which is typically a few volts higher than the threshold voltage
of the power MOSFET, VGS(TH). To achieve the targeted dVDS/dt, the gate driver must be capable of providing the
QGD charge in 20 ns or less. In other words, a peak current of 1.65 A (= 33 nC / 20 ns) or higher must be
provided by the gate driver. The UCC27518 and UCC27519 gate driver is capable of providing 4-A peak
sourcing current, which exceeds the design requirement and has the capability to meet the necessary switching
speed.
The 2.4x overdrive capability provides an extra margin against part-to-part variations in the QGD parameter of
the power MOSFET, along with additional flexibility to insert external gate resistors and fine tune the switching
speed for efficiency versus EMI optimizations. However, in practical designs the parasitic trace inductance in the
gate drive circuit of the PCB will have a definitive role to play on the power MOSFET switching speed. The effect
of this trace inductance is to limit the dI/dt of the output current pulse of the gate driver.
To illustrate this, consider the output current pulse waveform from the gate driver to be approximated to a
triangular profile, where the area under the triangle (½ ×IPEAK × time) would equal the total gate charge of the
power MOSFET (QG parameter in SPP20N60C3 power MOSFET datasheet = 87 nC typical). If the parasitic
trace inductance limits the dI/dt, the full peak current capability of the gate driver may not be fully achieved in the
time required to deliver the QG required for the power MOSFET switching. In other words, the time parameter in
the equation would dominate and the IPEAK value of the current pulse would be much less than the true peak
current capability of the device, while the required QG is still delivered. Because of this, the desired switching
speed may not be realized, even when theoretical calculations indicate the gate driver is capable of achieving the
targeted switching speed. Thus, place the gate driver device very close to the power MOSFET and design a tight
gate drive-loop with minimal PCB trace inductance to realize the full peak-current capability of the gate driver.
10.2.2.5 Enable and Disable Function
Certain applications demand independent control of the output state of the driver without involving the input
signal. The UCC27518 and UCC27519 devices offer the Enable pin, which achieves this.
10.2.2.6 Propagation Delay
The acceptable propagation delay from the gate driver is dependent on the switching frequency at which it is
used, and the acceptable level of pulse distortion to the system. The UCC27518 and UCC27519 devices feature
industry best-in-class 17-ns (typical) propagation delays, which ensure very little pulse distortion and allow
operation at very high-frequencies. See Switching Characteristics for the propagation and switching
characteristics of the UCC27518 and UCC27519 devices.
20
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
10.2.3 Application Curve
Input Threshold Voltage / VDD (%)
70
VDD = 12V
Turn−On
Turn−Off
50
30
−50
0
50
Temperature (°C)
100
150
G001
Figure 25. Input Threshold vs Temperature
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
21
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
11 Power Supply Recommendations
The bias supply voltage range for which the UCC27518 and UCC27519 device is rated to operate is from 4.5 V
to 18 V. The lower end of this range is governed by the internal under voltage-lockout (UVLO) protection feature
on the VDD pin supply circuit blocks. Whenever the driver is in UVLO condition with the VDD pin voltage below the
V(ON) supply start threshold, this feature holds the output low, regardless of the status of the inputs. The upper
end of this range is driven by the 20-V absolute maximum voltage rating of the VDD pin of the device (which is a
stress rating). Keeping a 2-V margin to allow for transient voltage spikes, the maximum recommended voltage for
the VDD pin is 18 V.
The UVLO protection feature also involves a hysteresis function. When the VDD pin bias voltage has exceeded
the threshold voltage and the device begins to operate, if the voltage drops, the device continues to deliver
normal functionality unless the voltage drop exceeds the hysteresis specification VDD(hys). While operating at or
near the 4.5 V range, ensure that the voltage ripple on the auxiliary power supply output is smaller than the
hysteresis specification of the device to avoid triggering device shutdown.
During system shutdown, the device operation continues until the VDD pin voltage has dropped below the V(OFF)
threshold, which must be accounted for while evaluating system shutdown timing design requirements. Likewise,
at system startup the device does not begin operation until the VDD pin voltage has exceeded above the V(ON)
threshold. The quiescent current consumed by the internal circuit blocks of the device is supplied through the
VDD pin. The charge for source current pulses delivered by the OUT pin is also supplied through the same VDD
pin. As a result, every time a current is sourced out of the output pin (OUT), a corresponding current pulse is
delivered into the device through the VDD pin. Therefore, ensure that local bypass capacitors are provided
between the VDD and GND pins and located as close to the device as possible, for the purpose of decoupling. A
low ESR, ceramic surface mount capacitor is necessary. TI recommends to have 2 capacitors; a 100-nF ceramic
surface-mount capacitor which can be nudged very close to the pins of the device, and another surface-mount
capacitor of few microfarads added in parallel.
12 Layout
12.1 Layout Guidelines
Proper PCB layout is extremely important in a high-current, fast-switching circuit to provide appropriate device
operation and design robustness. The UCC27518 and UCC27519 gate driver incorporates short-propagation
delays and powerful output stages capable of delivering large current peaks with very fast rise and fall times at
the gate of power switch to facilitate voltage transitions very quickly. At higher VDD voltages, the peak-current
capability is even higher (4-A/4-A peak current is at VDD = 12 V). Very high di/dt can cause unacceptable ringing
if the trace lengths and impedances are not well controlled. The following circuit layout guidelines are strongly
recommended when designing with these high-speed drivers.
• Locate the driver device as close as possible to power device in order to minimize the length of high-current
traces between the output pins and the gate of the power device.
• Locate the VDD bypass capacitors between VDD and GND as close as possible to the driver with minimal
trace length to improve the noise filtering. These capacitors support high-peak current being drawn from VDD
during turnon of power MOSFET. TI highly recommends using low-inductance SMD components such as chip
resistors and chip capacitors.
• The turnon and turnoff current loop paths (driver device, power MOSFET and VDD bypass capacitor) should
be minimized as much as possible in order to keep the stray inductance to a minimum. High dI/dt is
established in these loops at two instances – during turnon and turnoff transients, which will induce significant
voltage transients on the output pin of the driver device and gate of the power switch.
• Wherever possible parallel the source and return traces, taking advantage of flux cancellation.
• Separate power traces and signal traces, such as output and input signals.
• Star-point grounding is a good way to minimize noise coupling from one current loop to another. The GND of
the driver should be connected to the other circuit nodes such as source of power switch, ground of PWM
controller etc at one, single point. The connected paths should be as short as possible to reduce inductance
and be as wide as possible to reduce resistance.
• Use a ground plane to provide noise shielding. Fast rise and fall times at OUT may corrupt the input signals
during transition. The ground plane must not be a conduction path for any current loop. Instead the ground
plane must be connected to the star-point with one single trace to establish the ground potential. In addition
22
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
Layout Guidelines (continued)
to noise shielding, the ground plane can help in power dissipation as well.
12.2 Layout Example
Figure 26. Layout Example
12.3 Thermal Considerations
The useful range of a driver is greatly affected by the drive power requirements of the load and the thermal
characteristics of the package. For a gate driver to be useful over a particular temperature range, the package
must allow for the efficient removal of the heat produced while keeping the junction temperature within rated
limits. The thermal metrics for the driver package is summarized in Thermal Information. For detailed information
regarding the thermal information table, refer to the Application Note from Texas Instruments entitled IC Package
Thermal Metrics (SPRA953).
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
23
UCC27518, UCC27519
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
www.ti.com
12.4 Power Dissipation
Power dissipation of the gate driver has two portions as shown in equation below:
PDISS = PDC + PSW
(2)
The DC portion of the power dissipation is PDC = IQ x VDD where IQ is the quiescent current for the driver. The
quiescent current is the current consumed by the device to bias all internal circuits such as input stage, reference
voltage, logic circuits, protections etc and also any current associated with switching of internal devices when the
driver output changes state (such as charging and discharging of parasitic capacitances, parasitic shoot-through
etc). The UCC27518 and UCC27519 features very low quiescent currents (less than 1 mA, refer Figure 7) and
contains internal logic to eliminate any shoot-through in the output driver stage. Thus the effect of the PDC on the
total power dissipation within the gate driver can be safely assumed to be negligible.
The power dissipated in the gate-driver package during switching (PSW) depends on the following factors:
• Gate charge required of the power device (usually a function of the drive voltage VG, which is very close to
input bias supply voltage VDD due to low VOH drop-out).
• Switching frequency.
• Use of external gate resistors.
When a driver device is tested with a discrete, capacitive load it is a fairly simple matter to calculate the power
that is required from the bias supply. The energy that must be transferred from the bias supply to charge the
capacitor is given by:
1
EG = CLOAD VDD2
2
where
•
•
CLOAD is load capacitor
VDD is bias voltage feeding the driver
(3)
There is an equal amount of energy dissipated when the capacitor is charged. This leads to a total power loss
given by the following:
PG = CLOAD VDD2 fSW
where
•
ƒSW is the switching frequency
(4)
The switching load presented by a power MOSFET/IGBT can be converted to an equivalent capacitance by
examining the gate charge required to switch the device. This gate charge includes the effects of the input
capacitance plus the added charge needed to swing the drain voltage of the power device as it switches between
the ON and OFF states. Most manufacturers provide specifications of typical and maximum gate charge, in nC,
to switch the device under specified conditions. Using the gate charge Qg, one can determine the power that
must be dissipated when charging a capacitor. This is done by using the equation, QG = CLOAD x VDD, to provide
the following equation for power:
PG = CLOAD VDD2 fSW = Qg VDD fSW
(5)
This power PG is dissipated in the resistive elements of the circuit when the MOSFET/IGBT is being turned on or
off. Half of the total power is dissipated when the load capacitor is charged during turnon, and the other half is
dissipated when the load capacitor is discharged during turnoff. When no external gate resistor is employed
between the driver and MOSFET/IGBT, this power is completely dissipated inside the driver package. With the
use of external gate-drive resistors, the power dissipation is shared between the internal resistance of driver and
external gate resistor in accordance to the ratio of the resistances (more power dissipated in the higher
resistance component). Based on this simplified analysis, the driver power dissipation during switching is
calculated as follows:
ROFF
RON
PSW = QG ´ VDD ´ fSW ´ (
+
)
(ROFF +RGATE ) (RON +RGATE )
where
•
•
24
ROFF = ROL
RON (effective resistance of pull-up structure) = 1.4 x ROL
Submit Documentation Feedback
(6)
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
UCC27518, UCC27519
www.ti.com
SLUSB33A – MAY 2012 – REVISED DECEMBER 2014
13 Device and Documentation Support
13.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 5. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
UCC27518
Click here
Click here
Click here
Click here
Click here
UCC27519
Click here
Click here
Click here
Click here
Click here
13.2 Trademarks
All trademarks are the property of their respective owners.
13.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
13.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: UCC27518 UCC27519
Submit Documentation Feedback
25
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
UCC27518DBVR
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 140
7518
UCC27518DBVT
ACTIVE
SOT-23
DBV
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 140
7518
UCC27519DBVR
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 140
7519
UCC27519DBVT
ACTIVE
SOT-23
DBV
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 140
7519
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of