SLUS456D − APRIL 1999 - REVISED AUGUST 2002
D Dual Output Drive Stages in Push-Pull
D
D
D
D
D
D
D
D
D OR N PACKAGE
(TOP VIEW)
Configuration
Current Sense Discharge Transistor to
Improve Dynamic Response
130-µA Typical Starting Current
1-mA Typical Run Current
Operation to 1 MHz
Internal Soft Start
On-Chip Error Amplifier With 2-MHz Gain
Bandwidth Product
On Chip VDD Clamping
Output Drive Stages Capable of 500-mA
Peak-Source Current, 1-A Peak-Sink Current
COMP
FB
CS
RC
1
8
2
7
3
6
4
5
VDD
OUTA
OUTB
GND
PW PACKAGE
(TOP VIEW)
1
2
3
4
OUTA
VDD
COMP
FB
8
7
6
5
OUTB
GND
RC
CS
description
The UCC3808A is a family of BiCMOS push-pull, high-speed, low-power, pulse-width modulators. The UCC3808A
contains all of the control and drive circuitry required for off-line or dc-to-dc fixed frequency current-mode switching
power supplies with minimal external parts count.
The UCC3808A dual output drive stages are arranged in a push-pull configuration. Both outputs switch at half the
oscillator frequency using a toggle flip-flop. The dead time between the two outputs is typically 60 ns to 200 ns
depending on the values of the timing capacitor and resistors, thus limiting each output stage duty cycle to less than
50%.
block diagram
FB
COMP
CS
2
1
3
22 k Ω
OVERCURRENT
COMPARATOR
PEAK CURRENT
COMPARATOR
8
VDD
7
OUTA
6
OUTB
5
GND
14 V
0.75 V
0.5 V
2.0 V
2.2 V
VDD OK
OSCILLATOR
S
Q
PWM
LATCH
R
1.2R
VDD−1 V
Q
S
S
Q
Q
R
R
T
Q
PWM
COMPARATOR
VDD
0.5 V
R
SOFT START
VOLTAGE
REFERENCE
SLOPE = 1 V/ms
4
Note: Pinout shown is for SOIC and PDIP packages. TSSOP pinout is different.
RC
UDG-00097
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
! " #$ %! " &$'(# ! ) !%*
)$#!" # ! "&%## ! " &% !+% !% " %, " "! $ %!"
"! ) ) - !.* )$#! & #%""/ ) %" ! %#%"" (. #($)%
!%"!/ (( & %!% "*
Copyright 2002, Texas Instruments Incorporated
www.ti.com
1
SLUS456D − APRIL 1999 - REVISED AUGUST 2002
description (continued)
The UCC3808A family offers a variety of package options, temperature range options, and choice of undervoltage
lockout levels. The family has UVLO thresholds and hysteresis options for off-line and battery powered systems.
Thresholds are shown in the table below.
The UCC3808A is an enhanced version of the UCC3808 family. The significant difference is that the A versions
feature an internal discharge transistor from the CS pin to ground, which is activated each clock cycle during the
oscillator dead time. The feature discharges any filter capacitance on the CS pin during each cycle and helps minimize
filter capacitor values and current sense delay.
ORDERING INFORMATION
Packaged Devices
TA = TJ
−40°C to 85°C
0°C to 70°C
UVLO Option
SOIC (D){
PDIP (N)
TSSOP (PW){
12.5 V/8.3 V
UCC2808AD−1
UCC2808AN−1
UCC2808APW−1
4.3 V/4.1 V
UCC2808AD−2
UCC2808AN−2
UCC2808APW−2
12.5 V/8.3 V
UCC3808AD−1
UCC3808AN−1
UCC3808APW−1
4.3 V/4.1 V
UCC3808AD−2
UCC3808AN−2
UCC3808APW−2
† D (SOIC−8) and PW (TSSOP−8) packages are available taped and reeled. Add TR suffix to device type (e.g.
UCC3808ADTR−1) to order quantities of 2500 devices per reel for SOIC-8 and 2000 devices per reel for TSSOP-8.
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†}
Supply voltage (IDD ≤ 10 mA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
OUTA/OUTB source current (peak) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 A
OUTA/OUTB sink current (peak) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 A
Analog inputs (FB, CS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VDD + 0.3 V, not to exceed 6 V
Power dissipation at TA = 25°C (N package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W
Power dissipation at TA = 25°C (D package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650 mW
Power dissipation at TA = 25°C (PW package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 mW
Storage temperature, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to150°C
Junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 150°C
Lead temperature (soldering, 10 sec.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
† Currents are positive into, negative out of the specified terminal. Consult Packaging Section of the Power Supply Control Data Book (TI Literature
Number SLUD003) for thermal limitations and considerations of packages.
electrical characteristics, TA = 0°C to 70°C for the UCC3808A-x, −40°C to 85°C for the UCC2808A-x,
VDD = 10 V (see Note 6), 1-µF capacitor from VDD to GND, R = 22 kΩ, C = 330 pF TA = TJ, (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
175
0.44
194
213
kHz
0.5
0.56
V/V
Oscillator Section
Oscillator frequency
Oscillator amplitude/VDD
See Note 1
NOTES: 1. Measured at RC. Signal amplitude tracks VDD.
6. For UCCx808A−1, set VDD above the start threshold before setting at 10 V.
2
www.ti.com
SLUS456D − APRIL 1999 - REVISED AUGUST 2002
electrical characteristics, TA = 0°C to 70°C for the UCC3808A-x, −40°C to 85°C for the UCC2808A-x,
VDD = 10 V (see Note 6), 1-µF capacitor from VDD to GND, R = 22 kΩ, C = 330 pF TA = TJ, (unless
otherwise noted)
Error Amplifier Section
Input voltage
COMP = 2 V
1.95
Input bias current
2
–1
Open loop voltage gain
COMP sink current
FB = 2.2 V,
COMP = 1 V
COMP source current
FB = 1.3 V,
COMP = 3.5 V
2.05
V
1
µA
60
80
dB
0.3
2.5
mA
–0.2
–0.5
mA
48
49
PWM Section
Maximum duty cycle
Measured at OUTA or OUTB
Minimum duty cycle
COMP = 0 V
50
%
0
%
Current Sense Section
Gain
See Note 2
Maximum input signal
COMP = 5 V
See Note 3
CS to output delay
COMP = 3.5 V,
CS from 0 mV to 600 mV
CS = 0.5 V,
RC = 5.5 V
CS source current
1.9
2.2
2.5
0.45
0.5
0.55
V
100
200
ns
−200
CS sink current
See Note 7
Over current threshold
COMP to CS offset
CS = 0 V
V/V
nA
5
10
mA
0.7
0.75
0.8
V
0.35
0.8
1.2
V
0.5
1
V
0.5
1
V
Output Section
OUT low level
I = 100 mA
OUT high level
I = −50 mA,
Rise time
CL = 1 nF
25
60
ns
Fall time
CL = 1 nF
25
60
ns
VDD – OUT
Undervoltage Lockout Section
UCCx808A−1
Start threshold
Minimum operating voltage after start
Hysteresis
11.5
12.5
13.5
V
UCCx808A−2
See Note 6
4.1
4.3
4.5
V
UCCx808A−1
7.6
8.3
9
V
UCCx808A−2
3.9
4.1
4.3
V
UCCx808A−1
3.5
4.2
5.1
V
UCCx808A−2
0.1
0.2
0.3
V
3.5
20
ms
130
260
µA
1
2
mA
14
15
V
Soft Start Section
COMP rise time
FB = 1.8 V,
Rise from 0.5 V to 4 V
Overall Section
Startup current
VDD < start threshold
Operating supply current
FB = 0 V,
CS = 0 V
IDD = 10 mA
See Note 4
VDD zener shunt voltage
NOTES: 2.
3.
4.
5.
6.
7.
See Note 5 and 6
13
DV
COMP, 0 ≤ V
Gain is defined by: A +
CS ≤ 0.4 V.
DV
CS
Parameter measured at trip point of latch with FB at 0 V.
Start threshold and zener shunt threshold track one another.
Does not include current in the external oscillator network.
For UCCx808A−1, set VDD above the start threshold before setting at 10 V.
The internal current sink on the CS pin is designed to discharge an external filter capacitor. It is not intended to be a dc sink path.
www.ti.com
3
SLUS456D − APRIL 1999 - REVISED AUGUST 2002
pin assignments
COMP: COMP is the output of the error amplifier and the input of the PWM comparator. The error amplifier in the
UCC3808A is a true low-output impedance, 2-MHz operational amplifier. As such, the COMP pin can both source
and sink current. However, the error amplifier is internally current limited, so that zero duty cycle can be externally
forced by pulling COMP to GND.
The UCC3808A family features built-in full-cycle soft start. Soft start is implemented as a clamp on the maximum
COMP voltage.
CS: The input to the PWM, peak current, and overcurrent comparators. The overcurrent comparator is only intended
for fault sensing. Exceeding the overcurrent threshold will cause a soft start cycle. An internal MOSFET discharges
the current sense filter capacitor to improve dynamic performance of the power converter.
FB: The inverting input to the error amplifier. For best stability, keep FB lead length as short as possible and FB stray
capacitance as small as possible.
GND: Reference ground and power ground for all functions. Due to high currents, and high frequency operation of
the UCC3808A, a low impedance circuit board ground plane is highly recommended.
OUTA and OUTB: Alternating high current output stages. Both stages are capable of driving the gate of a power
MOSFET. Each stage is capable of 500-mA peak-source current, and 1-A peak-sink current.
The output stages switch at half the oscillator frequency, in a push-pull configuration. When the voltage on the RC
pin is rising, one of the two outputs is high, but during fall time, both outputs are off. This dead time between the two
outputs, along with a slower output rise time than fall time, insures that the two outputs can not be on at the same
time. This dead time is typically 60 ns to 200 ns and depends upon the values of the timing capacitor and resistor.
The high-current-output drivers consist of MOSFET output devices, which switch from VDD to GND. Each output
stage also provides a very low impedance to overshoot and undershoot. This means that in many cases,
external-schottky-clamp diodes are not required.
RC: The oscillator programming pin. The UCC3808A’s oscillator tracks VDD and GND internally, so that variations
in power supply rails minimally affect frequency stability. Figure 1 shows the oscillator block diagram.
Only two components are required to program the oscillator: a resistor (tied to the VDD and RC), and a capacitor (tied
to the RC and GND). The approximate oscillator frequency is determined by the simple formula:
f
OSCILLATOR
+ 1.41
RC
where frequency is in Hz, resistance in Ohms, and capacitance in Farads. The recommended range of timing
resistors is between 10 kΩ and 200 kΩ and range of timing capacitors is between 100 pF and 1000 pF. Timing resistors
less than 10 kΩ should be avoided.
For best performance, keep the timing capacitor lead to GND as short as possible, the timing resistor lead from VDD
as short as possible, and the leads between timing components and RC as short as possible. Separate ground and
VDD traces to the external timing network are encouraged.
4
www.ti.com
SLUS456D − APRIL 1999 - REVISED AUGUST 2002
pin assignments (continued)
RC
4
FREQUENCY =
VDD
2
S
RC
(APPROXIMATE
FREQUENCY)
Q
R
1.41
OSCILLATOR
OUTPUT
0.2 V
UDG-00095
Figure 1. Block Diagram for Oscillator
NOTE A: The oscillator generates a sawtooth waveform on RC. During the RC rise time, the output stages alternate on time, but both stages are
off during the RC fall time. The output stages switch a 1/2 the oscillator frequency, with ensured duty cycle of < 50% for both outputs.
VDD: The power input connection for this device. Although quiescent VDD current is very low, total supply current
will be higher, depending on OUTA and OUTB current, and the programmed oscillator frequency. Total VDD current
is the sum of quiescent VDD current and the average OUT current. Knowing the operating frequency and the
MOSFET gate charge (Qg), average OUT current can be calculated from:
I
OUT
+ Qg
F, where F is frequency
To prevent noise problems, bypass VDD to GND with a ceramic capacitor as close to the chip as possible along with
an electrolytic capacitor. A 1-µF decoupling capacitor is recommended.
APPLICATION INFORMATION
A 200-kHz push-pull application circuit with a full-wave rectifier is shown in Figure 2. The output, VO, provides 5 V
at 50 W maximum and is electrically isolated from the input. Since the UCC3808A is a peak-current-mode controller
the 2N2907 emitter following amplifier (buffers the CT waveform) provides slope compensation which is necessary
for duty ratios greater than 50%. Capacitor decoupling is very important with a single ground IC controller, and a 1
µF is suggested as close to the IC as possible. The controller supply is a series RC for start-up, paralleled with a bias
winding on the output inductor used in steady state operation.
Isolation is provided by an optocoupler with regulation done on the secondary side using the TL431 adjustable
precision shunt regulator. Small signal compensation with tight voltage regulation is achieved using this part on the
secondary side. Many choices exist for the output inductor depending on cost, volume, and mechanicall strength.
Several design options are iron powder, molypermalloy (MPP), or a ferrite core with an air gap as shown here. The
main power transformer has a Magnetics Inc. ER28 size core made of P material for efficient operation at this
frequency and temperature. The input voltage may range from 36 V dc to 72 V dc.
www.ti.com
5
6
−
VIN
36 V TO 72 V
+
10 µF
4700 µF
www.ti.com
2.80 kΩ
0.1 µF
0.47 µF
86.6 kΩ
330 pF
2 kΩ
2.2 Ω
51 kΩ
1/4 W
CURRENT
SENSE
0.2 Ω
2K12907
IRF640
BYV
28−200
1000 pF
6
2
CS
3
UCC3808AD−1
7
2.2 Ω
330 pF
20 kΩ
432 Ω
4.99 kΩ
RC
PRIMARY
GROUND
4.99 kΩ
RC
4
5
OUTA OUTB GND
62 Ω
COMP FB
1
8
VDD
62 Ω
20 kΩ
BYV
28−200
IRF640
1000 pF
1 mH
10 Ω
12
NP1
NP2
2
1
6
H11A1
U3
3
240 Ω
0.01 µF
1 kV
EF25 7µH
5
4
DF02SGICT
NS2
NS1
32CTQ030
0.1 µF
ER28
8:2
0.1 µF
680 µF
3
2
1 TL431
470 pF
4700 pF 20 kΩ
COMP
LOOP A
LOOP B
0.01 µF
19.1 kΩ
19.1 kΩ
200 Ω
−
VO
5 V 50 W
+
SLUS456D − APRIL 1999 - REVISED AUGUST 2002
APPLICATION INFORMATION
UDG-00096
Figure 2. Typical Application Diagram: 48-V In, 5-V, 50-W Output
SLUS456D − APRIL 1999 - REVISED AUGUST 2002
TYPICAL CHARACTERISTICS
IDD
vs
OSCILLATOR FREQUENCY
OSCILLATOR FREQUENCY
vs
EXTERNAL RC VALUES
COMP TO CS OFFSET
vs
TEMPERATURE
14
1000
1.2
C = 100 pF
12
VDD = 10 V, t = 25
5C
1.0
C = 330 pF
100
C = 1000 pF
10
8
6
C = 820 pF
4
C = 560 pF
IDD
without load
2
50
100
150
0.6
0.4
0
0
200
200
400
RT − Timing Resistor − k Ω
600
800
1000
−55
1200
−35
−15
Oscillator Frequency − kHz
Figure 3
Figure 4
ERROR AMPLIFIER GAIN AND PHASE
RESPONSE
vs
FREQUENCY
140
70
120
60
Phase
50
100
40
80
30
60
20
40
Phase Margin - Degrees
160
65
85
105
125
400
C = 1000 pF
VDD = 5 V
350
250
300
Dead Time - ns
80
45
DEAD TIME
vs
TEMPERATURE
300
180
25
Figure 5
OUTPUT DEAD TIME
vs
EXTERNAL RC VALUES
90
5
Temperature - °C
Dead Time - ns
0
0.8
0.2
0
1
Gain dB
COMP - CS Offset - V
IDD
with 1 nF load
10
IDD -mA
Frequency - kHz
C = 220 pF
C = 560 pF
C = 820 pF
200
C = 330 pF
C = 220 pF
150
VDD = 7.5 V
250
200
VDD = 10 V
150
100
10
100
50
20
Gain
C = 100 pF
0
0
1
100
10000
0
50
1000000
50
100
150
200
250
RT − Timing Resistor − k Ω
Frequency − Hz
Figure 6
Figure 7
−100
−50
0
50
100
150
Temperature - °C
Figure 8
CS RDS(on)
vs
TEMPERATURE
RC RDS(on)
vs
TEMPERATURE
120
300
100
250
VDD = 5 V
Ohms
Ohms
VDD = 5 V
80
200
VDD = 7.5 V
150
60
VDD = 7.5 V
40
100
VDD = 10 V
VDD = 10 V
20
50
0
0
−100
−50
0
50
Temperature - °C
Figure 9
100
150
−100
−50
0
50
100
150
Temperature - °C
Figure 10
www.ti.com
7
PACKAGE OPTION ADDENDUM
www.ti.com
19-Feb-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
UCC2808AD-1
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2808A-1
UCC2808AD-1G4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2808A-1
UCC2808AD-2
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2808A-2
UCC2808AD-2G4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2808A-2
UCC2808ADTR-1
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2808A-1
UCC2808ADTR-1G4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2808A-1
UCC2808ADTR-2
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2808A-2
UCC2808ADTR-2G4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2808A-2
UCC2808AN-1
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UCC2808A
N-1
UCC2808AN-2
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UCC2808A
N-2
UCC2808AN-2G4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UCC2808A
N-2
UCC2808APW-1
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
2808A1
UCC2808APW-1G4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
2808A1
UCC2808APW-2
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
2808A2
UCC2808APW-2G4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
2808A2
UCC2808APWTR-1
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
2808A1
UCC2808APWTR-2
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
2808A2
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
19-Feb-2015
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
UCC3808AD-1
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
3808A-1
UCC3808AD-1G4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
3808A-1
UCC3808AD-2
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
3808A-2
UCC3808AD-2G4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
3808A-2
UCC3808ADTR-1
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
3808A-1
UCC3808ADTR-1G4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
3808A-1
UCC3808ADTR-2
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
3808A-2
UCC3808ADTR-2G4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
3808A-2
UCC3808AN-1
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UCC3808A
N-1
UCC3808AN-1G4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UCC3808A
N-1
UCC3808AN-2
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UCC3808A
N-2
UCC3808APW-2
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
3808A2
UCC3808APWTR-2
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
3808A2
UCC3808APWTR-2G4
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
3808A2
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
19-Feb-2015
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Mar-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
UCC2808ADTR-1
Package Package Pins
Type Drawing
SOIC
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
UCC2808ADTR-2
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
UCC2808APWTR-2
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
UCC3808ADTR-1
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
UCC3808ADTR-2
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Mar-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
UCC2808ADTR-1
SOIC
D
8
2500
340.5
338.1
20.6
UCC2808ADTR-2
SOIC
D
8
2500
340.5
338.1
20.6
UCC2808APWTR-2
TSSOP
PW
8
2000
367.0
367.0
35.0
UCC3808ADTR-1
SOIC
D
8
2500
340.5
338.1
20.6
UCC3808ADTR-2
SOIC
D
8
2500
340.5
338.1
20.6
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
