Product
Folder
Order
Now
Support &
Community
Tools &
Software
Technical
Documents
Reference
Design
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
SGLS245E – MAY 2020 – REVISED MAY 2020
UCC2813-x-Q1 Low-Power Economy BiCMOS Current-Mode PWM
1 Features
3 Description
•
•
The UCC2813-x-Q1 device family of high-speed, lowpower integrated circuits contains all of the control
and drive components required for off-line and DC-toDC fixed-frequency current-mode switching power
supplies with minimal parts count.
1
•
•
•
•
•
•
•
•
•
•
Qualified for automotive applications
AEC-Q100 qualified with the following results:
– Device temperature grade 1: –40°C to 125°C
TA
– Device HBM classification level 2: ±2 kV
– Device CDM classification level C5: >1000 V
100-µA typical starting supply current
500-µA typical operating supply current
Operation to 1 MHz
Internal soft start
Internal fault soft start
Internal leading-edge blanking of the currentsense signal
1-A totem-pole output
70-ns typical response from current-sense to gatedrive output
1.5% tolerance voltage reference
Same pinout as the UCC3802 device, UC3842
device, and UC3842A device families
These devices have the same pin configuration as
the UC284x device family, and also offer the added
features of internal full-cycle soft start and internal
leading-edge blanking of the current-sense input.
The UCC2813-x-Q1 device family offers a variety of
package options, choice of maximum duty cycle, and
choice of critical voltage levels. Devices with lower
reference voltage such as the UCC2813-3-Q1 and
UCC2813-5-Q1 fit best into battery operated systems,
while the higher reference and the higher UVLO
hysteresis of the UCC2813-2-Q1 device and
UCC2813-4-Q1 device make these ideal choices for
use in off-line power supplies.
The UCC2813-x-Q1 device series is specified for
operation from –40°C to 125°C.
Device Information(1)
PART NUMBER
2 Applications
•
•
•
UCC2813-x-Q1
Automotive power supplies
Auxiliary power supply for automotive hybrid and
electric vehicles
AC and DC power supplies
PACKAGE
BODY SIZE (NOM)
SOIC (8)
3.91 mm × 4.90 mm
TSSOP (8)
4.40 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Block Diagram
FB
COMP
CS
2
1
3
7 VCC
UCCx813-1
UCCx813-4
UCCx813-5
Only
Leading Edge
Blanking
1.5 V
Over Current
VCC
OK
REF/2
T Q
S Q
R
4V
Voltage
Reference
Oscillator
6 OUT
S Q
S Q
R
REF
OK
PWM
Latch
R
13.5 V
0.5 V
Full Cycle
Soft Start
Logic
Power
τ=4ms
1V
5 GND
8
4
REF
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
SGLS245E – MAY 2020 – REVISED MAY 2020
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
4
7.1
7.2
7.3
7.4
7.5
7.6
4
4
4
5
5
7
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 9
8.1 Overview ................................................................... 9
8.2 Functional Block Diagram ......................................... 9
8.3 Feature Description................................................... 9
8.4 Device Functional Modes........................................ 21
9
Application and Implementation ........................ 23
9.1 Application Information............................................ 23
9.2 Typical Application .................................................. 23
10 Power Supply Recommendations ..................... 32
11 Layout................................................................... 33
11.1 Layout Guidelines ................................................. 33
11.2 Layout Example .................................................... 34
12 Device and Documentation Support ................. 35
12.1
12.2
12.3
12.4
12.5
12.6
12.7
Documentation Support ........................................
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
35
35
35
35
35
35
35
13 Mechanical, Packaging, and Orderable
Information ........................................................... 35
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (October 2019) to Revision E
Page
•
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section. ................................................................................................ 1
•
Changed Updated notes under Abs Max table ..................................................................................................................... 4
•
Changed Additional information to Power Supply Recommendation section ..................................................................... 33
2
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
www.ti.com
SGLS245E – MAY 2020 – REVISED MAY 2020
5 Device Comparison Table
MAXIMUM DUTY
CYCLE
REFERENCE
VOLTAGE
TURNON
THRESHOLD
TURNOFF
THRESHOLD
UNIT
100%
5
7.2
6.9
V
UCC2813-1-Q1
50%
5
9.4
7.4
V
UCC2813-2-Q1
100%
5
12.5
8.3
V
UCC2813-3-Q1
100%
4
4.1
3.6
V
UCC2813-4-Q1
50%
5
12.5
8.3
V
UCC2813-5-Q1
50%
4
4.1
3.6
V
PART NUMBER (1)
UCC2813-0-Q1
(1)
The x in the part number refers to the operating temperature range difference between the UCC2813 devices and the UCC2813
devices.
6 Pin Configuration and Functions
N and D Packages
8-Pin PDIP and SOIC
Top View
PW Package
8-Pin TSSOP
Top View
COMP
1
8
REF
COMP
1
8
REF
FB
2
7
VCC
FB
2
7
VCC
CS
3
6
OUT
CS
3
6
OUT
RC
4
5
GND
RC
4
5
GND
Not to scale
Not to scale
Pin Functions
PIN
I/O
DESCRIPTION
NAME
NO.
COMP
1
O
COMP is the output of the error amplifier and the input of the PWM comparator. Feedback loop
compensation is applied between this pin and the FB pin.
CS
3
I
CS is the input to the current-sense comparators: the PWM comparator and the overcurrent comparator.
FB
2
I
FB is the inverting input of the error amplifier.
GND
5
—
GND is the reference ground and power ground for all functions of this device.
OUT
6
O
OUT is the output of a high-current power driver capable of driving the gate of a power MOSFET.
RC
4
I
RC is the oscillator timing programming pin. An external resistor and capacitor are applied to this input to
program the switching frequency and maximum duty-cycle.
REF
8
O
REF is the voltage reference for the error amplifier and many other functions, and is the bias source for logic
functions of this device.
VCC
7
I
VCC is the bias-power input for this device. In normal operation, VCC is connected to a voltage source
through a current-limiting resistor.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
3
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
SGLS245E – MAY 2020 – REVISED MAY 2020
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MAX
UNIT
VCC voltage (3)
MIN
12
V
VCC current
30
mA
OUT current
±1
A
OUT energy (capacitive load)
20
µJ
6.3 or
VVCC + 0.3 (4)
V
Analog inputs
FB, CS, RC, COMP
Power dissipation at TA < 25°C
–0.3
N package
1
D package
0.65
Lead temperature, soldering (10 s)
W
300
°C
Junction temperature
–55
150
°C
Storage temperature, Tstg
–65
150
°C
(1)
(2)
(3)
(4)
All voltages are with respect to GND. All currents are positive into the specified terminal.
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
In normal operation Vcc is powered through a current limit resistor. The resistor must be sized so that the VCC voltage under all
operating conditions is below 12 V but above the turnoff threshold. Absolute maximum of 12 V applies when VCC is driven from a low
impedance source such that ICC does not exceed 30mA. Failure to limit VCC and ICC to these limits may result in permanent damage
of the device.This is further discussed in the Power Supply Recommendations
Whichever is smaller.
7.2 ESD Ratings
VALUE
V(ESD)
(1)
Electrostatic discharge
Human-body model (HBM), per AEC Q100-002 (1)
±2000
Charged-device model (CDM), per AEC Q100-011 (1)
±1000
UNIT
V
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specifications.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
VVCC
VCC bias supply voltage from a low impedance source
IVCC
Supply bias current
VOUT
Gate driver output voltage
IOUT
Average OUT pin current
IREF
REF pin output current
Voltage on analog pins
fOSC
(1)
4
Oscillator frequency
–0.1
FB, CS, RC, COMP
–0.1
MAX
UNIT
11
V
25
mA
VVCC
V
20
mA
5
mA
6 or
VVCC (1)
1
V
MHz
Whichever is smaller.
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
www.ti.com
SGLS245E – MAY 2020 – REVISED MAY 2020
7.4 Thermal Information
UCC2813-x-Q1
THERMAL METRIC (1)
D (SOIC)
PW (TSSOP)
8 PINS
8 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
107.5
153.8
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
49.3
38.4
°C/W
RθJB
Junction-to-board thermal resistance
48.7
83.8
°C/W
ψJT
Junction-to-top characterization parameter
6.6
2.2
°C/W
ψJB
Junction-to-board characterization parameter
48
82
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and device Package Thermal Metrics
application report.
7.5 Electrical Characteristics
Unless otherwise stated, these specifications apply for –40°C ≤ TA ≤ 125°C , TJ = TA; VVCC = 10 V (1); RT = 100 kΩ from REF
to RC; CT = 330 pF from RC to GND; 0.1-µF capacitor from VCC to GND; 0.1-µF capacitor from VREF to GND.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
4.925
5
5.075
3.94
4
4.06
UNIT
REFERENCE
Output voltage
Load regulation
Total variation
TJ = 25°C, I = 0.2 mA, UCC2813-[0,1,2,4]-Q1
TJ = 25°C, I = 0.2 mA, UCC2813-[3,5]-Q1
0.2 mA < I < 5 mA
10
30
UCC2813-[0,1,2,4]-Q1 (2)
4.84
5
5.1
UCC2813-[3,5]-Q1 (2)
3.84
4
4.08
Output noise voltage
10 Hz ≤ f ≤ 10 kHz, TJ = 25°C (3)
Long term stability
TA = 125°C, 1000 hours (3)
Output short circuit current
V
mV
V
70
µV
5
mV
–5
–35
mA
OSCILLATOR
Oscillator frequency
Temperature stability
UCC2813-[0,1,2,4]-Q1 (4)
40
46
52
UCC2813-[3,5]-Q1 (4)
26
31
36
See note
(3)
Amplitude peak-to-peak
kHz
2.5%
2.25
Oscillator peak voltage
2.4
2.55
2.45
V
V
ERROR AMPLIFIER
Input voltage
VCOMP = 2.5 V; UCC2813-[0,1,2,4]-Q1
2.42
2.5
2.56
VCOMP = 2 V; UCC2813-[3,5]-Q1
1.92
2
2.05
Input bias current
–2
Open loop voltage gain
60
COMP sink current
VFB = 2.7 V, VCOMP = 1.1 V
COMP source current
VFB = 1.8 V, VCOMP = VREF – 1.2 V
Gain-bandwidth product
See note
2
80
0.3
–0.2
(3)
µA
dB
3.5
–0.5
V
–0.8
2
mA
mA
MHz
PWM
Maximum duty cycle
Minimum duty cycle
(1)
(2)
(3)
(4)
UCC2813-[0,2,3]-Q1
97%
99%
100%
UCC2813-[1,4,5]-Q1
48%
49%
50%
VCOMP = 0 V
0%
Adjust VCC above the start threshold before setting at 10 V.
Total variation includes temperature stability and load regulation.
Ensured by design. Not 100% tested in production.
Output frequency for the UCC2813-[0,2,3]-Q1 device is the oscillator frequency. Output frequency for the UCC2813-[1,4,5]-Q1 device is
one-half the oscillator frequency.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
5
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
SGLS245E – MAY 2020 – REVISED MAY 2020
www.ti.com
Electrical Characteristics (continued)
Unless otherwise stated, these specifications apply for –40°C ≤ TA ≤ 125°C , TJ = TA; VVCC = 10 V(1); RT = 100 kΩ from REF
to RC; CT = 330 pF from RC to GND; 0.1-µF capacitor from VCC to GND; 0.1-µF capacitor from VREF to GND.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
1.1
1.65
1.8
0.9
1
1.1
V
200
nA
CURRENT SENSE
(5)
Gain
See note
Maximum input signal
VCOMP = 5 V (6)
Input bias current
–200
CS blank time
50
100
150
ns
1.32
1.55
1.7
V
0.45
0.9
1.35
V
I = 20 mA, all parts
0.1
0.4
I = 200 mA, all parts
0.35
0.9
I = 50 mA, VVCC = 5 V, UCC2813-[3,5]-Q1
0.15
0.4
Over-current threshold
COMP to CS offset
V/V
VCS = 0 V
OUTPUT
OUT low level
I = 20 mA, VCC = 0 V, all parts
I = –20 mA, all parts
VVCC –
OUT
OUT high Vsat
I = –200 mA, all parts
0.7
1.2
0.15
0.4
1
1.9
V
V
I = –50 mA, VVCC = 5 V, UCC2813-[3,5]-Q1
0.4
0.9
Rise time
CL = 1 nF
41
70
ns
Fall time
CL = 1 nF
44
75
ns
UNDERVOLTAGE LOCKOUT
Start threshold
Stop threshold
(7)
(7)
UCC2813-0-Q1
6.6
7.2
7.8
UCC2813-1-Q1
8.6
9.4
10.2
UCC2813-[2,4]-Q1
11.5
12.5
13.5
UCC2813-[3,5]-Q1
3.7
4.1
4.5
UCC2813-0-Q1
6.3
6.9
7.5
UCC2813-1-Q1
6.8
7.4
8
UCC2813-[2,4]-Q1
7.6
8.3
9
UCC2813-[3,5]-Q1
Start to stop hysteresis
V
V
3.2
3.6
4
UCC2813-0-Q1
0.12
0.3
0.48
UCC2813-1-Q1
1.6
2
2.4
UCC2813-[2,4]-Q1
3.5
4.2
5.1
UCC2813-[3,5]-Q1
0.2
0.5
0.8
4
10
ms
0.1
0.23
mA
V
SOFT START
COMP rise time
VFB = 1.8 V, Rise from 0.5 V to REF – 1 V
Start-up current
VVCC < start threshold
Operating supply current
VFB = 0 V, VCS = 0 V, VRC = 0 V
VCC internal Zener voltage (7) (8)
IVCC = 10 mA
OVERALL
VCC internal Zener voltage minus
UCC2813-[2,4]-Q1
start-threshold voltage (7)
A=
(5)
(6)
(7)
(8)
6
DVCOMP
DVCS
0.5
1.2
mA
12
13.5
15
V
0.5
1
V
0 £ VCS £ 0.8 V
Gain is defined by:
.
Parameter measured at trip point of latch with FB at 0 V.
Start threshold, stop threshold, and Zener-shunt thresholds track one another.
The device is fully operating in clamp mode as the forcing current is higher than the normal operating supply current.
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
www.ti.com
SGLS245E – MAY 2020 – REVISED MAY 2020
7.6 Typical Characteristics
4.00
80
3.98
60
135
3.96
3.94
VREF (V)
Phase
90
Phase (º)
Gain (dB)
40
Gain
45
20
3.92
3.90
3.88
3.86
0
0
3.84
3.82
-20
10k
10k
100k
1M
10M
4
4.2
Frequency (Hz)
C001
5
5.2
VCC (V)
ILOAD = 0.5 mA
4.8
5.4
5.6
5.8
6
1000
10
Oscillator Freq. (kHz)
1000
Oscillator Freq. (kHz)
4.6
Figure 2. UCC2813-[3,5]-Q1: VREF vs VCC
Figure 1. Error Amplifier Gain and Phase Response
0p
F
100
20
0p
33
0p
F
F
100
10
0p
F
20
0p
F
33
0p
F
1n
F
10
10
1n
10
100
1000
F
10
RT (kΩ)
100
1000
RT (kΩ)
Figure 3. UCC2813-[0,1,2,4]-Q1: Oscillator Frequency vs
RT and CT
Figure 4. UCC2813-[3,5]-Q1: Oscillator Frequency vs RT and
CT
100
50
99.5
F
p
00
=1
pF
30
48
pF
00
=3
96.5
=2
97
48.5
CT
F
p
00
pF
30
=3
pF
00
=2
CT
97.5
=1
98
49
CT
CT
98.5
CT
Maximum Duty Cycle (%)
49.5
99
CT
Maximum Duty Cycle (%)
4.4
47.5
96
47
95.5
46.5
95
10
100
1000
10
100
1000
Oscillator Frequency (kHz)
Oscillator Frequency (kHz)
Figure 5. UCC2813-[0,2,3]-Q1: Maximum Duty Cycle vs
Oscillator Frequency
Figure 6. UCC2813-[1,4,5]-Q1: Maximum Duty Cycle vs
Oscillator Frequency
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
7
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
SGLS245E – MAY 2020 – REVISED MAY 2020
www.ti.com
Typical Characteristics (continued)
16
8
14
7
12
C
VC
=
C
1nF
8V,
C=
8
VC
6
Loa
0V, No
C=1
4
2
0
0
100
200
300
400
500
600
700
800
C
VC
nF
=8
3
VCC =
2
No Load
0
=1
1
V,
4
d
VC
VCC = 8V,
VC
5
ICC (mA)
ICC (mA)
10
nF
1
V,
6
F
1n
V,
10
o Loa
10V, N
d
, No Load
VCC = 8V
1
0
0
900 1000
100
200
Oscillator Frequency (kHz)
300
400
500
600
700
800
900 1000
Oscillator Frequency (kHz)
Figure 7. UCC2813-0-Q1: ICC vs Oscillator Frequency
Figure 8. UCC2813-5-Q1: ICC vs Oscillator Frequency
500
1.1
Dead Time (ns)
400
350
UCCx813/5
300
250
200
UCCx813/1/2/4
150
100
COMP to CS Offset (Volts)
450
1.0
0.9
0.8
Slope = 1.8mV/°C
0.7
0.6
50
0
100
200
300
400
500
600
700
CT (pF)
RT = 100 kΩ
Figure 9. Dead Time vs CT
8
Submit Documentation Feedback
800
900
1000
0
-55-50
-25
0
25
50
75
100
125
Temperature (°C)
VCS = 0 V
Figure 10. COMP To CS Offset vs Temperature
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
www.ti.com
SGLS245E – MAY 2020 – REVISED MAY 2020
8 Detailed Description
8.1 Overview
The UCC2813-x-Q1 family of high-speed, low-power integrated circuits contain all of the control and drive
functions required for off-line and DC-to-DC fixed-frequency current-mode switched-mode power supplies having
minimal external parts count. The UCC2813-x-Q1 family is a cost-reduced version of the UCCx80x family, with
some relaxation of certain parameter limits. See Differences Between the UCC3813 and UCC3800 PWM
Families for more information.
These devices have the same pin configuration as the UC284x and UC284xA families, and also offer the added
features of internal full-cycle soft start and internal leading-edge blanking of the current-sense input. The
UCC2813-x-Q1 devices are pin-out compatible with the UC284x and UC284xA families, however they are not
plug-in compatible. In general, the UCC2813-x-Q1 requires fewer external components and consumes less
operating current.
The UCC2813-x-Q1 series is specified for the automotive temperature range of −40°C to 125°C.
8.2 Functional Block Diagram
FB
COMP
CS
2
1
3
7 VCC
UCCx813-1
UCCx813-4
UCCx813-5
Only
Leading Edge
Blanking
1.5 V
Over Current
VCC
OK
REF/2
T Q
S Q
R
4V
Voltage
Reference
Oscillator
6 OUT
S Q
S Q
R
REF
OK
PWM
Latch
R
13.5 V
0.5 V
Full Cycle
Soft Start
Logic
Power
τ=4ms
1V
5 GND
8
4
REF
Copyright © 2016, Texas Instruments Incorporated
8.3 Feature Description
The UCC2813-x-Q1 family offers numerous advantages that allow the power supply design engineer to meet
their challenging requirements.
Features include:
• Bi-CMOS process
• Low starting supply current: typically 100 µA
• Low operating supply current: typically 500 µA
• Pinout compatible with UC2842 and UC2842A families
• 5-V operation (UCC2813-[3,5]-Q1)
• Leading-edge blanking of current-sense signal
• On-chip soft start for start-up and fault recovery
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
9
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
SGLS245E – MAY 2020 – REVISED MAY 2020
www.ti.com
Feature Description (continued)
•
•
•
•
•
•
•
Internal full cycle restart delay
1.5% voltage reference
Up to 1-MHz oscillator
Low self-biasing output during UVLO
70-ns response from current sense to output
Very few external components required
Available in surface-mount and PDIP packages
8.3.1 Detailed Pin Descriptions
8.3.1.1 COMP
COMP is the output of the error amplifier and the input of the PWM comparator. Unlike earlier-generation
devices, the error amplifier in the UCC2813-x-Q1 device family is a true low-output-impedance 2-MHz
operational amplifier. As such, the COMP terminal both sources and sinks current. However, the error amplifier is
internally current limited, so zero duty cycle may be commanded by externally forcing COMP to GND.
The UCC2813-x-Q1 device family features built-in full cycle soft start at power up and after fault recovery, and no
external components are necessary. Soft start is implemented as a rising clamp on the COMP voltage,
increasing from 0 V to 5 V in 4 ms.
8.3.1.2 CS
CS is the input to the current-sense comparators. The UCC2813-x-Q1 current sense is significantly different from
its predecessor. The UCC2813-x-Q1 device family has two different current-sense comparators: the PWM
comparator and an overcurrent comparator. The overcurrent comparator is intended only for fault sensing, and
exceeding the overcurrent threshold causes a soft-start cycle. The earlier UC3842 family current-sense input
connects to only the PWM comparator.
The UCC2813-x-Q1 device family contains digital current-sense filtering, which disconnects the CS terminal from
the current sense comparator during the 100-ns interval immediately following the rising edge of the OUT pin.
This digital filtering, also called leading-edge blanking, prevents false triggering due to leading edge noises which
means that in most applications, no analog filtering (external R-C filter) is required on CS. Compared to an
external RC filter technique, the leading-edge blanking provides a smaller effective CS-to-OUT delay. However,
the minimum non-zero on-time of the OUT signal is determined by the leading-edge-blanking time and the CS-toOUT propagation delay. The gain of the current sense amplifier is typically 1.65 V/V in the UCC2813-x-Q1 family
versus typically 3 V/V in the UC3842 family. Connect CS directly to MOSFET source current sense resistor.
8.3.1.3 FB
FB is the inverting input of the error amplifier. For best stability, keep the FB lead length as short as possible and
FB stray capacitance as small as possible. At 2 MHz, the gain-bandwidth of the error amplifier is twice that of
earlier UC3842 family devices, and feedback design techniques are identical.
8.3.1.4 GND
GND is the signal reference ground and power ground for all functions on this part. TI recommends separating
the signal return paths and the high current gate driver path so that signals are not affected by the switching
current.
8.3.1.5 OUT
OUT is the output of a high-current power driver capable of driving the gate of a power MOSFET with peak
currents exceeding ±750 mA (up to ±1 A). OUT is actively held low when VCC is below the UVLO threshold. This
feature eliminates the need for a gate-to-source bleeder resistor associated with the MOSFET gate drive.
10
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
www.ti.com
SGLS245E – MAY 2020 – REVISED MAY 2020
Feature Description (continued)
The high-current power driver consists of CMOS FET output devices, which can switch all of the way to GND
and all of the way to VCC. The output provides very smooth rising and falling waveforms, providing very low
impedances to overshoot and undershoot which means that in many cases, external Schottky clamp diodes may
not be necessary on the output. Finally, no external gate voltage clamp is necessary with the UCC2813-x-Q1 as
the on-chip Zener diode automatically clamps the output to VCC.
8.3.1.6 RC
RC is the oscillator timing pin. For fixed frequency operation, set the timing-capacitor charging current by
connecting a resistor from REF to RC. Set frequency by connecting a timing capacitor from RC to GND. For best
performance, keep the timing capacitor lead to GND as short and direct as possible. If possible, use separate
ground traces for the timing capacitor and all other functions.
The UCC2813-x-Q1’s oscillator allows for operation to 1 MHz versus 500 kHz with the UC3842 family. Both
devices make use of an external resistor to set the charging current for the capacitor, which determines the
oscillator frequency. For the UCC2813-[0,1,2,4]-Q1, use Equation 1.
1.5
f =
R´C
where
•
•
•
ƒ is the oscillator frequency in hertz (Hz)
R is the timining resistance in ohms (Ω)
C is the timing capacitance in farads (F)
(1)
For the UCC2813-[3,5]-Q1, use Equation 2.
1.0
f =
R´C
(2)
The recommended timing resistance is from 10 kΩ to 200 kΩ and timing capacitance is from 100 pF to 1000 pF.
Never use a timing resistor less than 10 kΩ.
The two equations are different due to different reference voltages. The peak-to-peak amplitude of the oscillator
waveform is 2.45 V versus 1.7 V in UC3842 family. For best performance, keep the timing capacitor lead to GND
as short as possible. TI recommends separate ground traces for the timing capacitor and all other pins. The
maximum duty cycle for the UCC2813-[0,2,3]-Q1 is approximately 99%; the maximum duty cycle for the
UCC2813-[1,4,5]-Q1 is approximately 49%. The duty cycle cannot be easily modified by adjusting RT and CT,
unlike the UC3842A family. The maximum duty cycle limit is set by the ratio of the external oscillator charging
resistor RT and the internal oscillator discharge transistor on-resistance, like the UC3842. However, maximum
duty cycle limits less than 90% (for the UCC2813-[0,2,3]-Q1) and less than 45% (for the UCC2813-[1,4,5]-Q1)
can not reliably be set in this manner. For better control of maximum duty cycle, consider using the UCCx807.
8.3.1.7 REF
REF is the voltage reference for the error amplifier and also for many other functions on the IC. REF is also used
as the logic power supply for high speed switching logic on the IC. The UCC2813-[0,1,2,4]-Q1 have a 5-V
reference and the UCC2813-[3,5]-Q1 have a 4-V reference. Both have ±1.5% accuracy at 25°C versus ±2% in
the UC3842 family. The REF output short-circuit current is lower at 5 mA, compared to 30 mA in the UC3842
family.
For reference stability and to prevent noise problems with high speed switching transients, it is important to
bypass REF to GND with a ceramic capacitor as close to the pins as possible. A minimum of 0.1-µF ceramic is
required. Additional REF bypassing is required for external loads greater than 2.5 mA on the reference. An
electrolytic capacitor can also be used in addition to the ceramic capacitor.
When VCC is greater than 1 V and less than the UVLO on-threshold, REF is internally pulled to ground through
a 5-kΩ resistor which means that REF can be used as a logic output indicating power-system status.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
11
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
SGLS245E – MAY 2020 – REVISED MAY 2020
www.ti.com
Feature Description (continued)
8.3.1.8 VCC
VCC is the power input connection for this device. In normal operation, VCC is powered through a current
limiting resistor to a low-impedance source. To prevent noise problems, bypass VCC to GND with a 0.1-µF
ceramic capacitor in parallel as close to the VCC pin as possible. An electrolytic capacitor can also be used in
addition to the ceramic capacitor.
Although quiescent VCC current is very low, total supply current is higher, depending on the OUT current. Total
VCC current is the sum of quiescent VCC current and the average OUT current. Knowing the switching
frequency f and the MOSFET gate charge (Qg), average OUT current can be calculated from Equation 3.
IOUT = Qg ´ f
(3)
The UCC2813-x-Q1 has a lower VCC (supply voltage) clamp of 13.5 V typical versus 30 V on the UC3842. For
applications that require a higher VCC voltage, a resistor must be placed in series with VCC to increase the
source impedance. The maximum value of this resistor is calculated with Equation 4.
Rmax=
VIN:min; -VVCC:max;
IVCC +Qg ×f
where
•
•
•
•
VIN(min) is the minimum voltage that is used to supply VCC
VVCC(max) is the maximum VCC clamp voltage of the controller
IVCC is the device supply current without considering the gate driver current
Qg is the external power MOSFET gate charge, and f is the switching frequency
(4)
Additionally, the UCC2813-x-Q1 has an on-chip Zener diode to limit VCC to 13.5 V, which also limits the
maximum OUT voltage. If the bias-supply source is always lower than 12 V, it may be connected directly to VCC.
With UVLO thresholds at 4.1 V and 3.6 V for the UCC2813-3-Q1 and UCC2813-5-Q1, respectively, 5-V PWM
operation is now possible.
8.3.2 Undervoltage Lockout (UVLO)
The UCC2813-x-Q1 devices feature undervoltage lockout protection circuits for controlled operation during
power-up and power-down sequences. Both the supply voltage (VVCC) and the reference voltage (VREF) are
monitored by the UVLO circuitry. During UVLO, an active-low, self-biasing totem-pole output structure is also
incorporated for enhanced power switch protection.
Undervoltage lockout thresholds for the UCC2813-[2,3,4,5]-Q1 devices are different from the previous generation
of UCx84[2,3,4,5]-Q1 PWM controllers. The thresholds are optimized for two groups of applications: off-line
power supplies and DC-DC converters. See Table 1 for the specific thresholds for each device.
Table 1. UVLO Level Comparison Table
DEVICE
VON (V)
VOFF (V)
UCC2813-0-Q1
7.2
6.9
UCC2813-1-Q1
9.4
7.4
UCC2813-[2,4]-Q1
12.5
8.3
UCC2813-[3,5]-Q1
4.1
3.6
The UCC2813-[2,4]-Q1 feature typical UVLO thresholds of 12.5 V for turnon and 8.3 V for turnoff, providing 4.3 V
of hysteresis.
For low voltage inputs, which include battery and 5-V applications, the UCC2813-[3,5]-Q1 turn on at 4.1 V and
turn off at 3.6 V with 0.5 V of hysteresis.
The UCC2813-[0,1]-Q1 have UVLO thresholds optimized for automotive and battery applications.
During UVLO, the device draws approximately 100 µA of supply current. Once VCC crosses the turnon
threshold, the device supply current increases typically to about 500 µA, over an order of magnitude lower than
bipolar counterparts. Figure 11 indicates the supply current behavior at the relative UVLO turnon and turnoff
thresholds, not including average OUT current.
12
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
www.ti.com
SGLS245E – MAY 2020 – REVISED MAY 2020
Figure 11. Device Supply Current at UVLO
8.3.3 Self-Biasing, Active Low Output
The self-biasing, active-low clamp circuit shown in Figure 12 eliminates the potential for problematic MOSFET
turnon. As the PWM output voltage rises while in UVLO, the P-channel device drives the larger N-channel switch
ON, which clamps the output voltage low. Power to this circuit is supplied by the externally rising gate voltage, so
full protection is available regardless of the device's supply voltage during undervoltage lockout.
2V
VCC = OPEN
VOUT
VCC = 2 V
VCC = 0 V
VCC = 1 V
1V
50 mA
100 mA
IOUT
Figure 12. Internal Circuit Holding OUT Low During
UVLO
Figure 13. OUT Voltage vs OUT Current During
UVLO
8.3.4 Reference Voltage
The traditional 5-V band-gap-derived reference voltage of the UC3842 family can be also found on the
UCC2813-[0,1,2,4]-Q1 devices. However, the reference voltage of the UCC2813-[3,5]-Q1 devices is 4 V. This
change was necessary to facilitate operation with input supply voltages below 5 V. Many of the reference voltage
specifications are similar to the UC3842 devices although the test conditions have been changed, indicative of
lower-current PWM applications. Similar to their bipolar counterparts, the BiCMOS devices internally pull the
reference voltage low during UVLO, which can be used as a logic status indication.
The 4-V reference voltage on the UCC2813-[3,5]-Q1 is derived from the supply voltage (VVCC) and requires
about 0.5 V of headroom to maintain regulation. Whenever VVCC is below approximately 4.5 V, the reference
voltage also drops outside of its specified range for normal operation. The relationship between VVCC and VREF
during this excursion is shown in Figure 14.
The noninverting input to the error amplifier is tied to one-half of the controller's reference voltage (VREF). This
input is 2 V on the UCC2813-[3,5]-Q1 and 2.5 V on the higher reference voltage parts: the UCC2813-[0,1,2,4]Q1.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
13
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
SGLS245E – MAY 2020 – REVISED MAY 2020
www.ti.com
4.0 V
UCC3813-x
3.9 V
REF
VREF
3.8 V
R
TO
3.7 V
E/A+
R
3.6 V
0.1 µF
BYPASS
3.5 V
3.6 V 3.8 V 4.0 V 4.2 V 4.4 V 4.6 V 4.8 V 5.0 V
VCC
Figure 14. UCC2813-3-Q1 REF Output vs VVCC
Figure 15. Required Reference Bypass Minimum
Capacitance
8.3.5 Oscillator
The UCC2813-x-Q1 oscillator generates a sawtooth waveform on RC. The rise time is set by the time constant of
RT and CT. The fall time is set by CT and an internal transistor on-resistance of approximately 130 Ω. During the
fall time, the output is OFF and the maximum duty cycle is reduced below 50% or 100%, depending on the part
number. Larger values for the timing capacitor increase the discharge time and reduce the maximum duty cycle
and frequency slightly, as seen in Figure 5 and Figure 6 .
REF
8
0.2V
+
RT
R
+
RC
4
Q
S
2.65V
CT
Figure 16. Oscillator Equivalent Circuit
The oscillator section of the UCC2813-x-Q1 BiCMOS family has few similarities to the UC3842 type — other than
single-pin programming. It does still use a resistor to the reference voltage and capacitor to ground to program
the oscillator frequency up to 1 MHz. Timing component values must be changed because a much lower
charging current is desirable for low-power operation. Several characteristics of the oscillator have been
optimized for high-speed, noise-immune operation. The oscillator peak-to-peak amplitude has been increased to
2.45 V typical versus 1.7 V on the UC3842 family. The lower oscillator threshold has been dropped to
approximately 0.2 V while the upper threshold remains fairly close to the original 2.8 V at approximately 2.65 V.
Discharge current of the timing capacitor has been increased to nearly 20-mA peak as opposed to roughly 8 mA.
This can be represented by approximately 130 Ω in series with the discharge switch to ground. The higher
current is necessary to achieve brief dead times and high duty cycles with high-frequency operation. Practical
applications can use these devices to a 1-MHz switching frequency.
14
Submit Documentation Feedback
Copyright © 2020, Texas Instruments Incorporated
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
www.ti.com
SGLS245E – MAY 2020 – REVISED MAY 2020
1000
800
2.65 V
600
400
ƒ (kHz)
VCT
0.2 V
0V
200
CT = 100 p
100
80
60
fCONV
CT = 180 p
CT = 270 p
CT = 390 p
CT = 470 p
40
20
0
20
40
60
80
100
120
RT (kW)
Figure 17. Oscillator Waveform at RC
Figure 18. Oscillator Frequency vs RT For Several
CT
8.3.6 Synchronization
Synchronization of these PWM controllers is best obtained by the universal technique shown in Figure 19. The
device oscillator is programmed to free-run at a frequency about 20% lower than that of the synchronizing
frequency. A brief positive pulse is applied across the 50-Ω resistor to force synchronization. Typically, a 1-V
amplitude pulse of 100-ns width is sufficient for most applications.
The controller can also be synchronized to a pulse-train applied directly to the oscillator RC pin. The device
internally pulls low at this node once the upper oscillator threshold is crossed. This 130-Ω impedance to ground
remains active until the voltage on RC is lowered below 0.2 V. External synchronization circuits must
accommodate these conditions.
REF
RT
RC
CT
SYNC
§ 50
Figure 19. Synchronizing the Oscillator
8.3.7 PWM Generator
Maximum duty cycle is higher for these devices than for their UC384x predecessors. This is primarily due to the
higher ratio of timing capacitor discharge-to-charge current, which can exceed one hundred-to-one in a typical
BiCMOS application. Attempts to program the oscillator maximum duty cycle much below the specified range, by
adjusting the timing component values of RT and CT, must be avoided. There are two reasons to refrain from this
design practice. First, the device's high discharge current would necessitate higher charging current than
necessary for programming, defeating the purpose of low power operation. Second, a low-value timing resistor
may prevent the capacitor from discharging to the lower threshold and initiating the next switching cycle.
Copyright © 2020, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC2813-0-Q1 UCC2813-1-Q1 UCC2813-2-Q1 UCC2813-3-Q1 UCC2813-4-Q1 UCC2813-5Q1
15
UCC2813-0-Q1, UCC2813-1-Q1, UCC2813-2-Q1, UCC2813-3-Q1
UCC2813-4-Q1, UCC2813-5-Q1
SGLS245E – MAY 2020 – REVISED MAY 2020
www.ti.com
8.3.8 Minimum Off-Time Adjustment (Dead-Time Control)
Dead time is the term used to describe the ensured OFF time of the PWM output during each oscillator cycle. It
is used to ensure that even at maximum duty cycle, there is enough time to reset the magnetic circuit elements,
and prevent saturation. The dead time of the UCC2813-x-Q1 PWM family is determined by the internal 130-Ω
discharge impedance and the timing capacitor value. Larger capacitance values extend the dead time whereas
smaller values results in higher maximum duty cycles for the same operating frequency. A curve for dead time
versus timing capacitor values is provided in Figure 20. Further increasing the dead time is possible by adding a
low-value resistor between the RC pin and the timing components, as shown in Figure 21. The dead time
increases with increasing discharge resistor value to about 470 Ω as indicated from the curve in Figure 22.
Higher resistances must be avoided as they can decrease the dead time and reduce the oscillator peak-to-peak
amplitude. Sinking too much current (1 mA) by reducing RT will freeze the oscillator OFF by preventing discharge
to the lower comparator threshold voltage of 0.2 V. Adding this discharge control resistor has several impacts on
the oscillator programming. First, it introduces a DC offset to the capacitor during the discharge interval – but not
the charging interval of the timing cycle, thus lowering the usable peak-to-peak timing capacitor amplitude.
Because of the reduced peak-to-peak amplitude, the exact value of CT may require adjustment to obtain the
correct oscillator frequency. One alternative is keep the same value timing capacitor and adjust both the timing
and discharge resistor values because these are readily available in finer numerical increments.
200
180
REF
160
RT
Td (ns)
140
RD
120
RC