SLUS347A – MAY 1995 – REVISED APRIL 2003
FEATURES
D Complies with SCSI, SCSI–2 and SPI–2
D
D
D
D
D
D
D
D
D
D
DESCRIPTION
Standards
2.7-V to 5.25-V Operation
1.8-pF Channel Capacitance during
Disconnect
0.5-µA Supply Current in Disconnect Mode
110-Ω/2.5-kΩ Programmable Termination
Completely Meets SCSI Hot Plugging
–400-mA Sourcing Current for Termination
+400-mA Sinking Current for Active Negation
Drivers
Trimmed Termination Current to 4%
Trimmed Impedance to 7%
Current Limit and Thermal Shutdown
Protection
The UCC5606 provides 9 lines of active termination for
a small computer systems interface (SCSI) parallel bus.
The SCSI standard recommends active termination at
both ends of the cable segment.
The UCC5606 is ideal for high performance 3.3-V SCSI
systems. The key features contributing to such low
operating voltage are the 0.1-V drop out regulator and
the 2.7-V reference. During disconnect the supply
current is typically only 0.5 µA, which makes the device
attractive for battery powered systems.
The UCC5606 is designed with an ultra-low channel
capacitance of 1.8 pF, which eliminates effects on signal
integrity from disconnected terminators at interim points
on the bus.
BLOCK DIAGRAM
UDG–94067–1
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Copyright 2003, Texas Instruments Incorporated
!"# $"%&! '#(
'"! ! $#!! $# )# # #*
"#
'' +,( '"! $!# - '# #!# &, !&"'#
# - && $## (
www.ti.com
1
SLUS347A – MAY 1995 – REVISED APRIL 2003
DESCRIPTION (CONTINUED)
The UCC5606 can be programmed for either a 110-Ω or 2.5-kΩ termination. The 110-Ω termination is used for
standard SCSI bus lengths and the 2.5-kΩ termination is typically used in short bus applications. When driving
the TTL compatible DISCNCT pin directly, the 110-Ω termination is connected when the DISCNCT pin is driven
high, and disconnected when low. When the DISCNCT pin is driven through an impedance between 80 kΩ and
150 kΩ, the 2.5-kΩ termination is connected when the DISCNCT pin is driven high, and disconnected when
driven low.
The power amplifier output stage allows the UCC5606 to source full termination current and sink active negation
current when all termination lines are actively negated.
The UCC5606 is pin-for-pin compatible with Unitrode’s other 9-line single-ended SCSI terminators, except that
DISCNCT is now active low, allowing lower capacitance and lower voltage upgrades to existing systems. The
UCC5606 is completely hot pluggable and appears as high impedance at the terminating channels with
VTRMPWR = 0 V or open.
Internal circuit trimming is utilized, first to trim the 110-Ω termination impedance to a 7% tolerance, and then most
importantly, to trim the output current to a 4% tolerance, as close to the maximum SCSI specification as possible,
which maximizes noise margin in fast SCSI operation.
Other features include thermal shutdown and current limit.
This device is offered in low thermal resistance versions of the industry standard 16-pin narrow body SOIC,
16-pin N and 24-pin TSSOP.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted{}
UCC5606
TRMPWR voltage
7
Signal line voltage
0 to 7
Regulator output current
UNIT
V
0.6
A
Storage temperature, Tstg
–65 to 150
Operating junction temperature, TJ
–55 to 150
°C
C
Lead temperature (soldering, 10 sec.)
300
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is
not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect
to GND. Currents are positive into and negative out of, the specified terminal.
‡ Currents are positive into, negative out of the specified terminal. Consult Packaging Section of Databook for thermal limitations and
considerations of packages. All voltages are referenced to GND.
RECOMMENDED OPERATING CONDITIONS
MAX
UNIT
TRMPWR voltage
2.7
MIN
NOM
5.25
V
Signal line voltage
0
5
V
Disconnect input voltage
0
TRMPWR
°C
ORDERING INFORMATION
TA
0°C to 70°C
DISCONNECT
STATUS
PACKAGED DEVICE{
DIL–16 (N)
SOIC–16 (DP)
UCC5606N
UCC5606DP
TSSOP–24 (PWP)
UCC5606PWP
† The LQFP packages are available taped and reeled. Add TR suffix to device type (e.g. UCC5606PWPTR) to order quantities of 2,500 devices
per reel.
2
www.ti.com
SLUS347A – MAY 1995 – REVISED APRIL 2003
CONNECTION DIAGRAM
DIL–16 (Top View)
N Package
SOIC–16 (Top View)
DP Package
TSSOP–24 (Top View)
PWP Package
NOTE: GND* serves as a heat sink ground which must be tied to a large copper area or the grounding plate.
ELECTRICAL CHARACTERISTICS
TA = 0°C to 70°C, TRMPWR = 3.3 V, DISCNCT = 3.3 V, RDISCNCT = 0 Ω, TA = TJ, (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Supply Current Section
Termpwr supply current
Power down mode
All termination lines = open
1
2
All termination lines = 0.2 V
210
218
DISCNCT = 0 V
0.5
5.0
102.3
110.0
117.7
2.5
2.7
3.0
–22.1
–23.0
–24.0
–21
–23
–24
–20.2
–23.0
–24.0
–19
–23
mA
µA
Output Section (110 ohms – Terminator Lines)
Terminator impedance
Output high voltage
Max output current
TRMPWR = 3 V (1)
VLINE = 0.2 V,
VLINE = 0.2 V
TJ = 25°C
VLINE = 0.2 V,
TJ = 25°C (1)
VLINE = 0.2 V,
TRMPWR = 3 V,
Output leakage
VLINE = 0.5 V
DISCNCT = 0 V,
Output capacitance
DISCNCT = 0 V,
TRMPWR = 3 V (1)
Ohms
V
mA
–24
–22.4
TRMPWR = 0 V to 5.25 V
DP package (2)
10
400
nA
1.8
2.5
pF
2.0
2.5
3.0
kΩ
2.5
2.7
3.0
V
–0.7
–1.0
–1.4
–0.6
–1.0
–1.5
10
400
nA
1.8
2.5
pF
Output Section (2.5 kΩ – Terminator Lines) (RDISCNCT = 80 kΩ)
Terminator impedance
Output high voltage
TRMPWR = 3 V (1)
Max output current
VLINE = 0.2 V
VLINE = 0.2 V,
Output leakage
DISCNCT = 0 V,
Output capacitance
DISCNCT = 0 V,
TRMPWR = 3 V (1)
TRMPWR = 0 to 5.25 V
DP package (2)
www.ti.com
mA
3
SLUS347A – MAY 1995 – REVISED APRIL 2003
ELECTRICAL CHARACTERISTICS
TA = 0°C to 70°C, TRMPWR = 3.3 V, DISCNCT = 3.3 V, RDISCNCT = 0 Ω, TA = TJ, (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Regulator Section
Regulator output voltage
5.25 V > TRMPWR > 3 V
Drop-out voltage
All termination lines = 0.2 V
Short circuit current
Thermal shutdown
VREG = 0 V
VREG = 3 V
(2)
Thermal shutdown hysteresis
(2)
Sinking current capability
2.5
2.7
3.0
0.1
0.2
–200
–400
–800
200
400
800
V
mA
°C
170
10
Disconnect Section
Disconnect threshold
RDISCNCT = 0 kΩ to 80 kΩ
Input current
DISCNCT = 3.3 V
0.8
1.5
2.0
V
30
50
µA
NOTES: 1. Measuring each termination line while other eight are low (0.2 V).
2. Ensured by design. Not production tested.
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
NO.
DISCNCT
7
GND
9
LINE1 TO
LINE9
4
I
110-Ω termination channels
REG
9
I
Output of the internal 2.7-V regulator
TRMPWR
4
GND*
4
I/O
NAME
I
Taking this pin low causes the 9 channels to become high impedance and the chip to go into low
power mode. In short laptop buses an 80-kΩ to 150-kΩ resister to TERPWR terminates the bus at
2.5 kΩ. Less than 110 Ω to TERPWR enables the terminator.
Ground reference for the device
Power for the device
Heat sink ground, must be tied to a large copper area or the grounding plate.
www.ti.com
SLUS347A – MAY 1995 – REVISED APRIL 2003
APPLICATION INFORMATION
UDG–98100
Figure 1. Typical SCSI Bus Configurations Utilizing two UCC5606 Devices
UDG–98100
Figure 2. Typical Wide SCSI Bus Configurations Utilizing three UCC5606 Devices
www.ti.com
5
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
(3)
Device Marking
(4/5)
(6)
UCC5606PWPTR
ACTIVE
TSSOP
PW
24
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
UCC5606PWP
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of