XEVMK2EX

EVMK2E Evaluation Module Quick Start Guide ©2014 Texas Instruments Incorporated EVMK2E Evaluation Module A No Functionality F JTAG(MIPI-60) connector for SoC B 1 press: safe shutdown of SOC; 2 presses within 0.5sec: warm reset; 3 presses within 0.5sec: full reset; 4 presses within 0.5sec: cancel reset G COM2 : BMC UART Console C On board XDS200 USB D COM1 : SoC UART Console BMC Reset : Resets the microcontroller H and will reset the entire board Dip switch for boot configuration : 1111 : No Boot mode/JTAG DSP Little Endian I 0010 : NOR SPI ARM Master Boot E USB control of both SOC COM1 & BMC COM2 J USB3 PORT 1(Device and HOST Modes) K USB3 PORT 0(HOST only) ©2014 Texas Instruments Incorporated Two boot procedures are described below, one for Uboot and one for CCS. 1) Uboot Steps: 1 For Windows User: Insert pendrive and load USB COM drive by executing the program\drivers\ CP210xVCPInstaller_x86 For 64-bit systems execute the program\drivers\ For Linux User: Please download driver from any of below link as per Linux kernel version on PC. Compile the driver and install it. http://www.silabs.com/Support%20Documents/Software/Linux_3.x.x_VCP_Driver_Source.zip http://www.silabs.com/Support%20Documents/Software/Linux_2.6.x_VCP_Driver_Source.zip 2 Ensure EVM configuration switches are set as shown for NOR SPI Boot. 3 Connect the USB mini-B cable to J1 ©2014 Texas Instruments Incorporated 4 Open Tera Term, select COM port, configure settings, as shown in image. This serial port settings of Tera Term is shown as an example. It is not mandatory to use only Tera Term as a serial terminal 5 Insert DC-in cable to apply 12V power. 6 On SoC serial port console a display will be seen, as shown in image. Hit any key to stop auto-boot when prompted. EVM is now ready for Uboot applications. MCSDK Downlink Page: http://software-dl.ti.com/sdoemb/sdoemb_public_sw/mcsdk/latest/index_FDS.html ©2014 Texas Instruments Incorporated 2) CCS Steps: 1 Update or install CCS (V5.5.0.00077 or later) from MCSDK download page. 2 Ensure EVM configuration switch are set as shown for No Boot/JTAG DSP Little Endian Boot mode. 3 Connect the USB mini-B cable to XDS200. 4 Insert DCDC-in cable to apply 12V power. 5 Launch CCS CCS.. After CCS is opened, EVM is now ready ready for use. ©2014 Texas Instruments Incorporated Getting Started: Please see the ‘Getting Started’ chapter in the MCSDK User Guide for hardware and software setup: http://processors.wiki.ti.com/index.php/MCSDK_ User_Guide_for_KeyStone_II. TI Worldwide Technical Support Important Notes when handling the EVM: Plug in all the cables before powering ON the EVM to ensure proper grounding. Do not unnecessarily flex the boards, while inserting cables. Excessive flexing can break the PCB traces. Use proper ESD procedures when handling the EVM. Warning: Some components on the EVM may be too hot to touch with your bare hand when power is on. Product Information Centers Online Documentation TI device product page http://www.ti.com/product/66ak2e05 Multicore SDK http://www.ti.com/tool/bioslinuxmcsdk http://processors.wiki.ti.com/index.php/M CSDK_User_Guide_for_KeyStone_II CCS v5 http://processors.wiki.ti.com/index.php/Categ ory:Code_Composer _Studio_v5 C663X EVM Information: https://www.einfochips.com/tI-66ak2e-evm This link contains: Hardware & Software details User Guide Technical Reference Manual EVMK2E EVM Support: Please write to tievmsupport@einfochips.com for technical queries related to this EVM. eInfochips Address : eInfochips Limited. 303,Parishram Building,5/B Rashmi Society Mithakhali Six Road,Navarangpura. Ahmedabad- 380009. Gujarat, INDIA. Tel : +91-79-2656 3705. Fax :+91-79-2656 0722. http://www.einfochips.com/ Internet TI Semiconductor Product Information Center Home Page support.ti.com TI Semiconductor KnowledgeBase Home page support.ti.com/sc/knowledgebase Americas Phone +1(972) 644-5580 Fax +1(972)927-6377 Internet/Email support.ti.com/sc/pic/americas.htm Europe, Middle East and Africa Phone European Free Call 00800-ASK-TEXAS (00800 275 83927) International +49 (0) 8161 80 2121 Russian Support +7 495 981 0701 Note: The European Free Call (Toll Free) number is not active in all countries. If you have technical difficulty calling the free call number, please use the international number above. Fax +(49) (0) 8161 80 2045 Internet support.ti.com/sc/pic/euro.htm Japan Fax International Domestic Internet/Email International Domestic +81-3-3344-5317 0120-81-0036 support.ti.com/sc/pic/japan.htm www.tij.co.jp/pic Asia Phone International +91-80-413816651Domestic Toll-Free-Number Toll-Free-Number Australia 800-999-084 Malaysia 1-800-80-3973 China 800-820-8682 New Zealand 0800-446-934 Hong Kong 800-96-5941 Philippines 1-800-765-7404 India 1-800-425-7888 Singapore 800-886-1028 Indonesia 001-803-8861-1006 Taiwan 0800-006800 Korea 080-551-2804 Thailand 001-800-886-0010 Fax +886-2-2378-6808 Email Internet support.ti.com/sc/pic/asia.htm tiasia@ti.com ti-china@ti.com Important Notice: The products and services of Texas Instruments Incorporated and its subsidiaries described herein are sold subject to TI's standard terms and conditions of sale. Customers are advised to obtain the most current and complete information about TI products and services before placing orders. TI assumes no liability for applications assistance, customer's applications or product designs, software performance, or infringement of patents. The publication of information regarding any other company's products or services does not constitute TI's approval, warranty or endorsement thereof. The floating bar is a trademark of Texas Instruments. All other trademarks are the property of their respective owners ©2014 Texas Instruments Incorporated