XTCIEVMK2X

XTCIEVMK2X Evaluation Module Quick Start Guide © 2013 Texas Instruments Incorporated XTCIEVMK2X Evaluation Module A No Functionality F Reserve for factory programming 1 press: safe shutdown of SOC; 2 presses within 0.5sec: warm reset; B 3 presses with 0.5 sec: full reset; 4 presses with 0.5 sec: cancel reset G MCU Reset Jumper for BMC field update C COM2: SoC UART Console D COM1: MCU UART Console E Reserve for factory programming © 2013 Texas Instruments Incorporated Dip switch for boot configuration: 0001: No Boot/JTAG DSP Little Endian H Boot mode 0010: Uboot mode Provide 2 console ports in USB interface I ( same as “C” and “D”) MCU Reset: Resets the microcontroller J and will reset the entire board Two boot procedures are described below, one for Uboot and one for CCS. 1) Uboot Steps: 1 Ensure EVM configuration switch are set as shown for NOR SPI Boot. 2 Connect the USB mini-B cable to FTDI_USB. 3 Open HyperTerminal, select COM port, configure settings. © 2013 Texas Instruments Incorporated 4 Insert DC-in cable to apply 12V power. 5 Hit any key to stop auto-boot when prompted. EVM is now ready for Uboot applications. MCSDK Downlink Page: http://software-dl.ti.com/sdoemb/sdoemb_public_sw/mcsdk/latest/index_FDS.html 2) CCS Steps: 1 Update or install CCS (V5.3.0.00090 or later) from MCSDK download page. 2 Ensure EVM configuration switch are set as shown for No Boot/JTAG DSP Little Endian Boot mode. 3 Connect the USB mini-B cable to XDS200. © 2013 Texas Instruments Incorporated 4 Insert DC-in cable to apply 12V power. 5 Launch CCS. After CCS is opened, EVM is now ready for use. Note: 1. Refer to the following LCD and LED pictures for correct power-on behavior. © 2013 Texas Instruments Incorporated Getting Started: Please see the ‘Getting Started’ chapter in the MCSDK User Guide: http://processors.wiki.ti.com/index.php/MC SDK_User_Guide_for_KeyStone_II. Important Notes when handling the EVM:  Plug in all the cables before powering ON the EVM to ensure proper grounding.  Do not unnecessarily flex the boards, while inserting cables. Excessive flexing can break the PCB traces.  Use proper ESD procedures when handling the EVM.  Warning: Some components on the EVM may be too hot to touch with your bare hand when power is on. Online Documentation  TMS320C663X processor website http://www.ti.com/product/tci6634k2k http://www.ti.com/product/tci6636k2h http://www.ti.com/product/tci6638k2k  MCSDK website for updates http://processors.wiki.ti.com/index.ph p/MCSDK_User_Guide_for_KeyStone_ II  CCS v5 http://processors.wiki.ti.com/index.php/Categ ory:Code_Composer _Studio_v5 C663X EVM Information: http://www.advantech.com/Support/TI-EVM/default.a spx This link contains:    Hardware & Software details User Guide Technical Reference Manual TI Worldwide Technical Support Internet TI Semiconductor Product Information Center Home Page support.ti.com TI Semiconductor KnowledgeBase Home page support.ti.com/sc/knowledgebase Product Information Centers Americas Phone +1(972) 644-5580 Fax +1(972)927-6377 Internet/Email support.ti.com/sc/pic/americas.htm Europe, Middle East and Africa Phone European Free Call 00800-ASK-TEXAS (00800 275 83927) International +49 (0) 8161 80 2121 Russian Support +7 495 981 0701 Note: The European Free Call (Toll Free) number is not active in all countries. If you have technical difficulty calling the free call number, please use the international number above. Fax +(49) (0) 8161 80 2045 Internet support.ti.com/sc/pic/euro.htm Japan Fax International Domestic Internet/Email International Domestic +81-3-3344-5317 0120-81-0036 support.ti.com/sc/pic/japan.htm www.tij.co.jp/pic Asia Phone International +91-80-413816651Domestic Toll-Free-Number Toll-Free-Number Australia 800-999-084 Malaysia 1-800-80-3973 China 800-820-8682 New Zealand 0800-446-934 Hong Kong 800-96-5941 Philippines 1-800-765-7404 India 1-800-425-7888 Singapore 800-886-1028 Indonesia 001-803-8861-1006 Taiwan 0800-006800 Korea 080-551-2804 Thailand 001-800-886-0010 Fax +886-2-2378-6808 Email Internet support.ti.com/sc/pic/asia.htm tiasia@ti.com ti-china@ti.com TCIEVMK2X EVM Support: Please write to EVM667xsupport@advantech.com.tw for technical queries related to this EVM. Important Notice: The products and services of Texas Instruments Incorporated and its subsidiaries described herein are sold subject to TI's standard terms and conditions of sale. Customers are advised to obtain the most current and complete information about TI products and services before placing orders. TI assumes no liability for applications assistance, customer's applications or product designs, software performance, or infringement of patents. The publication of information regarding any other company's products or services does not constitute TI's approval, warranty or endorsement thereof. The floating bar is a trademark of Texas Instruments. All other trademarks are the property of their respective owners © 2013 Texas Instruments Incorporated