BVS-301GN4

BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS SMD LED PACKAGE CONFIGURATION 3.60 2.40 BVS-301GN4 DESCRIPTION Dice Material : GaN Green Light Color : Green Color Lens Color : Water Transparent 1.9 2.70 RADIATION PATTERN -30° 0° 30° INFRARED/VAPOR PHASE REFLOW SOLDERING 4.45 3.20 0.15 2.41 1.65 -60° 60° 1.90 0.80 3.60 100 75 50 25 0 25 50 75 100 Relative Luminous Intensity ( Iv % ) Tolerance ± 0.25 ABSOLUTE MAXIMUM RATINGS AT Ta = 25 PARAMETER Power Dissipation Continuous Forward Current Peak Forward Current ( 1/10 Duty Cycle , 0.1ms Pulse Width ) Reverse Voltage Derating Linear From 25 Operating Temperature Range Storage Temperature Range Reflow Soldering Condition 245 for 10 seconds MAX. 100 25 100 5 0.4 30 to 80 40 to 100 UNIT mW mA mA V mA/oC o C o C ELECTRICAL / OPTICAL CHARACTERISTICS AT Ta = 25 SYMBOL VF IR p d 2 1/2 PARAMETER Forward Voltage Reverse Current Peak Emission Wavelength Dominant Wavelength Viewing Angle TEST COND. I F = 20 mA V R = 5V I F = 20 mA I F = 20 mA I F = 20 mA MIN. TYP. 3.3 520 525 110 MAX. 4 10 UNIT V A nm nm Deg BIN GRADE LIMITS ( I F = 20 mA ) LUMINOUS INTENSITY / mcd Bin Min. Max. F 360 465 G 465 600 H 600 780 I J K 780 1000 1300 1000 1300 1680 Tolerance ± 15%mcd *Bright View reserves the rights to alter specifications and remove availability of products at any time without notice. *Dominant Wavelength, d is according to CIE Chromaticity Diagram base on color of lamps. * 1/2 is the off-axis angle where the luminous intensity is one half the on-axis intensity. *These products are sensitive to static electricity. Caution must be taken strictly to avoid static electricity. 2006/3/17 – C BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS SMD LED BVS-301GN4 TYPICAL ELECTRICAL / OPTICAL CHARACTERISTIC CURVES FIG. 1 Forward Current vs. Forward Voltage ( Ta = 25 °C ) 100 90 80 70 60 50 40 30 20 10 0 3.0 2.5 Relative Intensity 2.0 1.5 1.0 0.5 0 2.5 2.9 3.3 3.7 Forward Voltage Vf ( V ) 4.1 0 10 20 30 40 50 60 Forward Current If ( mA ) 70 Forward Current ( mA ) FIG. 2 Relative Intensity vs. Forward Current ( Ta = 25 °C ) FIG. 3 Forward Voltage vs. Temperature 1.2 Relative Intensity @ 20mA Forward Voltage @ 20mA 1.1 1.0 0.9 0.8 -50 3.0 2.5 2.0 1.5 1.0 0.5 FIG. 4 Relative Intensity vs. Temperature -25 0 25 50 75 100 125 0 -50 -25 0 25 50 75 100 125 Ambient Temperature Ta ( °C ) FIG. 5 Relative Intensity vs. Wavelength ( p ) ( Ta = 25 °C ) IF-DC Forward Current ( mA ) 1.0 Forward Intensity @ 20mA 40 30 20 10 0 0 Ambient Temperature Ta ( °C ) FIG. 6 Maximum Forward Current vs. Temperature 0.5 0 450 500 550 Wavelength ( nm ) 600 20 40 60 80 100 Ambient Temperature Ta ( °C ) 120 2006/3/17 - C CAUTION FOR STATIC ELECTRICITY(BASE UPON MACHINE MODE) “ ” ” ” BRIGHT VIEW ELECTRONICS CO.,LTD SMD APPLICATION ( PB FREE SOLDERING ) 1XX series. Apply to BVS-3XX Description: (1) Manual soldering (We do not recommend this method strongly.) (1.1) To prevent cracking,please bake (65 ,24hrs)before soldering. (1.2) Temperature at tip of iron: 250 Max.(25W) (1.3) It's banned to load any stress on the resin during soldering. (1.4) Soldering time: 3 sec. Max.(one time only) (2) Reflow Soldering (2.1) To prevent cracking,please bake (65 ,24hrs)before soldering. (2.2) When soldering,do not put stress on the LEDs during heating. (2.3) Never take next process until the component is cooled down to room temperature after reflow. (2.4) After soldering,do not warp the circuit board. (2.5) The recommended reflow soldering profile(measuring on the surface of the LED resin)is following: 10 SEC. MAX. 245 C MAX. 0.5 217 217 150 1 /SEC. MAX. 50 SEC. MAX. /SEC MAX. TEMPERATURE ~75 ~25 210 SEC. MIN. 100 SEC. MAX. TIME The reflow temperature 240 ~245 is recommended and the soldering temperature should be not higher than 245 (one time only) DOC. NO.:S-QW-K002 2006 / 02 / 08 - C BRIGHT VIEW ELECTRONICS CO.,LTD TOP LEDS PACKING (A) 2.0 0.05 Gap : Left Side 4.0 0.10 4.0 0.10 1.5 0.10 1.75 0.10 5.5 0.05 12.0 0.3 0.3 MAX. BVS-301 + + BVS-312 + + + + + 9.3 BVS-313 BVS-301-B + + + BVS-311 + BVS-311-B + BVS-313 Feeding direction Blue / Green / White : Black tape Others : Transparent tape 2.6 MAX. UNIT : mm 50 MIN. 178 2.0 13 TYP. Reel : 1,500PCS UNIT : mm Label 2 Label 1 Bright View PART NO.: Electronics Co.,Ltd. Electronics Co.,Ltd. Bright View PART NO.: LOT NO.: GRADE: Q'ty Xpcs LOT NO.: GRADE: Q'ty pcs QA BVS-30XXXX QA ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION Normal X: Bin grade : Wavelength : Vf Anti-electrostatic bag 24 39 RE Y CARTON Dimension(cm): 39*24*22 22 ITEM NO. DEVICE: Q'TY N. W.: G. W.: PCS. KGS. KGS. Carton : 20 Reels Total : 30,000PCS 2003 / 10 / 24 - B