BVU-439GN9

BRIGHT VIEW ELECTRONICS CO.,LTD OVAL LED LAMP PACKAGE CONFIGURATION BV-439 4.3 BV-439R 4.3 BVU-439GN9 DESCRIPTION Dice Material : GaN Green Light Color : Green Color Lens Color : Green Tinted Diffused Stand-Off P/N : BVU-439GN9 R 3.2 4.3 4.1 6.5 3.2 4.3 4.1 1.0Max. 10.2 0.5 1.3 1.0 25.4Min. 25.4Min. RADIATION PATTERN -30° 0° 30° -60° 60° CATHODE CATHODE 0.5 100 75 50 25 0 25 50 75 100 Relative Luminous Intensity ( Iv % ) 2.54 1.0Min 2.54 Tolerance ± 0.25 ㎜ ABSOLUTE MAXIMUM RATINGS AT Ta = 25 ℃ PARAMETER Power Dissipation (PD) Continuous Forward Current (IF) Peak Forward Current ( 1/10 Duty Cycle , 10ms Pulse Width ) (IFP) Reverse Voltage (VR) MAX. 120 30 100 5 0.4 UNIT mW mA mA V mA/oC Derating Linear From 25 ℃ Operating Temperature Range (Topr) －30 ℃ to ＋ 85 ℃ Storage Temperature Range (Tstg) －40 ℃ to ＋ 100 ℃ Lead Solder Temperature 1.6 mm Below Package 260 ℃ for 5 seconds (Tsld) ELECTRICAL / OPTICAL CHARACTERISTICS AT Ta = 25 ℃ SYMBOL VF IR λp λd 2θ1/2 IV PARAMETER Forward Voltage Reverse Current Peak Emission Wavelength Dominant Wavelength Viewing Angle Luminous Intensity TEST COND. I F = 20 mA V R = 5V I F = 20 mA I F = 20 mA I F = 20 mA I F = 20 mA MIN. TYP. 3.3 520 525 100/40 2800 MAX. 4.0 10 UNIT V μA nm nm Deg mcd 2180 BIN GRADE LIMITS (IF=20 mA) LUMINOUS INTENSITY / mcd Bin Min. Max. M 2180 2800 N 2800 3600 O 3600 4650 BIN GRADE LIMITS (IF=20 mA) DOMINANT WAVELENGTH / nm Bin Min. Max. PH 521 524 PI 524 527 PJ 527 530 Tolerance ± 15%mcd *Bright View reserves the rights to alter specifications and remove availability of products at any time without notice. *Dominant Wavelength, λd is according to CIE Chromaticity Diagram base on color of lamps. *θ1/2 is the off-axis angle where the luminous intensity is one half the on-axis intensity. *These products are sensitive to static electricity. Caution must be taken strictly to avoid static electricity. 2009/5/4 – A BRIGHT VIEW ELECTRONICS CO.,LTD OVAL LED LAMP BVU-439GN9 TYPICAL ELECTRICAL / OPTICAL CHARACTERISTIC CURVES FIG. 1 Forward Current vs. ( Ta = 25 °C ) Forward Voltage Relative Luminous Intensity. Normalized at 20mA FIG. 2 Relative Luminous Intensity vs. Forward Current ( Ta = 25 °C ) 120 Forward Current ( mA ) 100 80 60 40 20 5.0 4.0 3.0 2.0 1.0 0 0 2.3 2.8 3.3 3.8 Forward Voltage Vf ( V ) 4.3 0 20 60 40 80 100 Forward Current If ( mA ) 120 Relative Forward Voltage. Normalized at 20mA Relative Luminous Intensity. Normalized at 20mA 1.2 1.1 1.0 0.9 FIG. 3 Relative Forward Voltage vs. Temperature 3.0 2.5 2.0 1.5 1.0 0.5 FIG. 4 Relative Luminous Intensity vs. Temperature 0.8 -50 -25 0 25 50 75 100 125 0 -50 -25 0 25 50 75 100 125 Ambient Temperature Ta ( °C ) FIG. 5 Relative Intensity vs. Wavelength ( λp ) ( If =20mA , Ta = 25 °C ) Forward Current ( mA ) Ambient Temperature Ta ( °C ) FIG. 6 Maximum Forward Current vs. Temperature Relative Emission Intensity (a.u.) 1.0 40 30 20 10 0.5 0 450 500 550 Wavelength ( nm ) 600 0 0 20 40 60 80 100 Ambient Temperature Ta ( °C ) 120 2009/5/4 – A BRIGHT VIEW ELECTRONICS CO.,LTD OVAL LED LAMP BVU-439GN9 CAUTION FOR CLASS 1 ESD ( MACHINE MODE ) Gallium Nitride (GaN) based light emitting diodes (LEDs) are extremely sensitive to electrostatic discharge (ESD). Users are strongly recommended to take necessary meter to test the static and avoid ESD when handing these products. Bright View's BA, GN, WI series products are GaN based materials and are classified as "Class 1",( ESD endurance 50V or lower ), any manufacturing site or workstation where GaN devices are handled should be rated and controlled at 50V or below. Proper grounding of products or machines ( via 1MΩ ), using static dissipative mats, static dissipative containers, static dissipative working uniferms and shoes are considered to be effective against ESD. An ionizer is recommended in the facility or environment where ESD may be generated easily, and soldering iron with a grounded tip is also recommended. To install a protection device in the LED circuit to ensure the surge current and voltage not exceeding the max rating during on/off swithing. When inspecting the final products in which LEDs are assembled, it is recommended to check whether the assembled LEDs are damaged by ESD or not. It is simple to find damaged LEDs by light-on or a VF test at lower current (below 1mA is recommended). ESD damaged LEDs will show some unusual characteristics such as the remarkable increasing of leak current, the forward voltage become lower, or the LEDs do not light on at the low current. 2009/5/4 – A BRIGHT VIEW ELECTRONICS CO.,LTD OVAL LED LAMP BVU-439GN9 Apply to LAMP(DIP) series. Description: ( 1 ) Manual soldering (Solder Iron) (1.1) Temperature at tip of the iron: 300°C Max. (1.2) It's banned to load any stress on the resin during soldering. (1.3) Soldering time: 3 sec. Max.(one time only) (1.4) Leave 3mm of minimum distance from the base of epoxy. ( 2 ) Dip Soldering(Wave soldering-Solder Bath) (2.1) Leave 3mm of minimum distance from the base of the epoxy. Soldering beyond the base of the tie bar(stand off) is recommended. (2.2) When soldering, do not put stress on the LEDs during heating. (2.3) Cutting the leadframes at high temperatures may cause LED failure. (2.4) Never take next process until the component is cooled down to room temperature after reflow. (2.5) After soldering, do not warp the circuit board. (2.6) The recommended dip soldering profile is the following: Degree C. 3 00.0 275.0 250.0 225.0 200.0 175.0 150.0 125.0 100.0 75.0 50.0 25.0 0.0 MAX 260 C ， 5 s ec. >20 C Temperature ( C ) 4 C / sec. 150 C 0.0 50.0 100.0 150.0 200.0 250.0 300.0 Time ( sec. ) 2009/5/4 – A BRIGHT VIEW ELECTRONICS CO.,LTD OVAL LED LAMP BVU-439GN9 Label 1 Label 2 Bright View PART NO.: LOT NO.: GRADE: Q'ty Xpcs Electronics Co.,Ltd. Bright View PART NO.: LOT NO.: GRADE: Electronics Co.,Ltd. BVU-XXXXXXXX QA 3mm or 5mm Polybag Pb - Free / RoHS Compliant X: Bin grade : Wavelength : Vf Anti-electrostatic bag Q'ty pcs QA Pb - Free / RoHS Compliant ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION BOX Dimension(cm): 29*25*15 25 BVU - X X X X X X X R Stand-offs Luminous Grade -refer to the selection guide for BIN options Lens Color -refer to lens color (1) to (9) Dice Code -refer to the selection guide Lens Configuration -refer to lens drawing View Angle -refer to the selection guide (A) to (Z) Outline Dimension -refer to the outline dimension 29 3 15 TYPE Q'TY N,W G,W C.NO PCS KGS KGS Label 1 or Label 2 attach on it. Device 5mm(T-1 3/4) 3mm(T-1) Blue / Green / White Q'ty / Polybag (pcs) 1000pcs 1000pcs 500pcs Polybag / Box A 14 bags 20 bags 18 bags Fig. Label 1 Label 1 Label 2 32 53 RE Y CARTON Dimension(cm): 53*32*33 33 ITEM NO. DEVICE: Q'TY N. W.: G. W.: PCS. KGS. KGS. 4 Boxes / Carton 5mm : 56,000pcs 3mm : 80,000pcs Blue / Green / White : 36,000pcs 2009/5/4 – A