BVU-5K5TT4

BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS LED LAMP PACKAGE CONFIGURATION 5.9 5.9 BVU-5K5TT4 DESCRIPTION Dice Material : AlInGaP Yellow Light Color : Yellow Color Lens Color : Water Transparent Stand-Off P/N : BVU-5K5TT4 R 5.0 4.9 7.6 1.0Max. 12.0±0.5 RADIATION PATTERN -30° 0° 30° 1.0 1.3 1.0 25.4Min. -60° 60° 25.4Min. CATHODE CATHODE 0.5 2.54 100 75 50 25 0 25 50 75 100 1.0Min. 2.54 Relative Luminous Intensity ( Iv % ) Tolerance ± 0.25 ㎜ ABSOLUTE MAXIMUM RATINGS AT Ta = 25 ℃ PARAMETER Power Dissipation (PD) Continuous Forward Current (IF) Peak Forward Current ( 1/10 Duty Cycle , 10ms Pulse Width ) (IFP) Reverse Voltage (VR) MAX. 80 30 100 5 0.4 UNIT mW mA mA V mA/oC Derating Linear From 50 ℃ Operating Temperature Range (Topr) －30 ℃ to ＋ 85 ℃ Storage Temperature Range (Tstg) －40 ℃ to ＋ 100 ℃ Lead Solder Temperature 1.6 mm Below Package 260 ℃ for 5 seconds (Tsld) ELECTRICAL / OPTICAL CHARACTERISTICS AT Ta = 25 ℃ SYMBOL VF IR λp λd 2θ1/2 IV PARAMETER Forward Voltage Reverse Current Peak Emission Wavelength Dominant Wavelength Viewing Angle Luminous Intensity TEST COND. I F = 20 mA V R = 5V I F = 20 mA I F = 20 mA I F = 20 mA I F = 20 mA MIN. TYP. 2.3 592 590 25 7800 MAX. 2.8 100 UNIT V μA nm nm Deg mcd 6000 BIN GRADE LIMITS (IF=20 mA) LUMINOUS INTENSITY / mcd Bin Min. Max. Q 6000 7800 R 7800 10000 S 10000 13000 BIN GRADE LIMITS (IF=20 mA) DOMINANT WAVELENGTH / nm Bin Min. Max. YD 586 589 YE 589 592 YF 592 595 Tolerance ± 15%mcd *Bright View reserves the rights to alter specifications and remove availability of products at any time without notice. *Dominant Wavelength, λd is according to CIE Chromaticity Diagram base on color of lamps. *θ1/2 is the off-axis angle where the luminous intensity is one half the on-axis intensity. 2009/6/23 - B BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS LED LAMP BVU-5K5TT4 TYPICAL ELECTRICAL / OPTICAL CHARACTERISTIC CURVES FIG. 1 Forward Current vs. Forward Voltage ( Ta = 25 °C ) FIG. 2 Relative Intensity vs. Forward Current ( Ta = 25 °C ) 120 Forward Current ( mA ) 100 80 60 40 20 5.0 Relative Intensity 4.0 3.0 2.0 1.0 0 0 1.3 1.8 2.3 2.8 Forward Voltage Vf ( V ) 3.3 0 20 40 80 100 60 Forward Current If ( mA ) 120 1.2 Forward Voltage ( a.u ) 1.1 1.0 0.9 FIG. 3 Forward Voltage vs. Temperature ( If = 20 mA ) Relative Intensity ( a.u ) 3.0 2.5 2.0 1.5 1.0 0.5 FIG. 4 Relative Intensity vs. Temperature ( If = 20 mA ) 0.8 -50 -25 0 25 50 75 100 125 0 -50 -25 0 25 50 75 100 125 Ambient Temperature Ta ( °C ) FIG. 5 Relative Intensity vs. Wavelength ( λp ) ( Ta = 25 °C ) IF-DC Forward Current ( mA ) Ambient Temperature Ta ( °C ) FIG. 6 Maximum Forward Current 40 30 20 10 0 0 vs. Temperature Relative Emission Intensity ( a.u) 1.0 0.5 0 500 550 600 Wavelength ( nm ) 650 20 40 60 80 100 Ambient Temperature Ta ( °C ) 120 2009/6/23 - B BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS LED LAMP BVU-5K5TT4 Apply to LAMP(DIP) series. Description: ( 1 ) Manual soldering (Solder Iron) (1.1) Temperature at tip of the iron: 300°C Max. (1.2) It's banned to load any stress on the resin during soldering. (1.3) Soldering time: 5 sec. Max.(one time only) (1.4) Leave 1.6mm of minimum distance from the base of epoxy. ( 2 ) Dip Soldering(Wave soldering-Solder Bath) (2.1) Leave 1.6mm of minimum distance from the base of the epoxy. Soldering beyond the base of the tie bar(stand off) is recommended. (2.2) When soldering, do not put stress on the LEDs during heating. (2.3) Cutting the leadframes at high temperatures may cause LED failure. (2.4) Never take next process until the component is cooled down to room temperature after reflow. (2.5) After soldering, do not warp the circuit board. (2.6) The recommended dip soldering profile is the following: Degree C. 3 00.0 275.0 250.0 225.0 200.0 175.0 150.0 125.0 100.0 75.0 50.0 25.0 0.0 0.0 50.0 MAX 260 C ， 5 s ec. >20 C Temperature ( C ) 4 C / sec. 150 C 100.0 150.0 200.0 250.0 300.0 Time ( sec. ) 2009/6/23 - B BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS LED LAMP BVU-5K5TT4 Label 1 Label 2 Bright View PART NO.: LOT NO.: GRADE: Q'ty Xpcs Electronics Co.,Ltd. Bright View PART NO.: LOT NO.: GRADE: Electronics Co.,Ltd. BVU-XXXXXXXX QA 3mm or 5mm Polybag Pb - Free / RoHS Compliant X: Bin grade : Wavelength : Vf Anti-electrostatic bag Q'ty pcs QA Pb - Free / RoHS Compliant ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION BOX Dimension(cm): 29*25*15 25 BVU - X X X X X X X R 29 3 15 TYPE Q'TY N,W G,W C.NO PCS KGS KGS Stand-offs Luminous Grade -refer to the selection guide for BIN options Lens Color -refer to lens color (1) to (9) Dice Code -refer to the selection guide Lens Configuration -refer to lens drawing View Angle -refer to the selection guide (A) to (Z) Outline Dimension -refer to the outline dimension Label 1 or Label 2 attach on it. Device 5mm(T-1 3/4) 3mm(T-1) Blue / Green / White Q'ty / Polybag (pcs) 1000pcs 1000pcs 500pcs Polybag / Box A 14 bags 20 bags 18 bags Fig. Label 1 Label 1 Label 2 32 53 RE Y CARTON Dimension(cm): 53*32*33 33 ITEM NO. DEVICE: Q'TY N. W.: G. W.: PCS. KGS. KGS. 4 Boxes / Carton 5mm : 56,000pcs 3mm : 80,000pcs Blue / Green / White : 36,000pcs 2009/6/23 - B