10A4

10A005 10.0 AMP SILICON RECTIFIERS THRU 10A10 VOLTAGE RANGE 50 TO 1000 Volts CURRENT 10.0 Amperes R-6 FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability .360(9.1) .340(8.6) DIA. 1.0(25.4) MIN. MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Axial leads, solderable per MIL-STD-202, method 208 guranteed * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 1.65 grams .360(9.1) .340(8.6) .052(1.3) .048(1.2) DIA. 1.0(25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Ta=60 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 10.0A Maximum DC Reverse Current Ta=25 C at Rated DC Blocking Voltage Ta=100 C Typical Junction Capacitance (Note 1) Typical Thermal Resistance RθJA (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: 10A05 50 35 50 10A1 100 70 100 10A2 200 140 200 10A4 400 280 400 10.0 400 1.0 10.0 400 100 10 -65 +150 10A6 600 420 600 10A8 800 560 800 10A10 1000 700 1000 UNITS V V V A A V µA µA pF C/W C 1. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 2. Thermal Resistance from Junction to Ambient .375" (9.5mm) lead length. 128 RATING AND CHARACTERISTIC CURVES (10A005 THRU 10A10) FIG.1-TYPICAL FORWARD CHARACTERISTICS 500 INSTANTANEOUS FORWARD CURRENT,(A) AVERAGE FORWARD CURRENT,(A) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE 12 10 8 6 4 2 0 Single Phase Half Wave 60Hz Resistive Or Inductive Load 0.375"(9.5mm) Lead Length 100 40 10 Tj=25 C Pulse Width 300us 1% Duty Cycle 0 20 40 60 80 100 120 140 160 180 200 AMBIENT TEMPERATURE,( C) 1 FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT,(A) 500 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 400 FORWARD VOLTAGE,(V) 300 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 200 100 FIG.3 - TYPICAL REVERSE CHARACTERISTICS 100 0 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz 10 REVERSE LEAKAGE CURRENT, ( µA) Tj=100 C FIG.5 - TYPICAL THERMAL RESISTANCE VS. LEAD LENGTH 1.0 THERMAL RESISTANCE, ( C/W) 25 20 15 10 5 .1 Tj=25 C .01 0 20 40 60 80 100 120 140 0 .1 .2 .3 .4 .5 .6 .7 .8 .9 1.0 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) EQUAL LEAD LENGTH TO HEAT SINK, INCHES 129