SF166

SF161 16.0 AMP SUPER FAST RECTIFIERS THRU SF168 VOLTAGE RANGE 50 to 600 Volts CURRENT FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability * Good for switching mode application 16.0 Amperes .412 (10.5) MAX. 3.8 φ +.2 HOLE THRU .248 (6.3) TO-220 .180 (4.6) .050 (1.27) .108 (2.75) MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Lead solderable per MIL-STD-202, method 208 guranteed * Polarity: As Marked * Mounting position: Any * Weight: 2.24 grams .051 MAX. (1.3) .040 MAX. (1.0) .100 (2.54) PIN 1 PIN 3 Positive CT Suffix "C" .595 (15.1) MAX. .550 (14.0) .158 (4.0) MIN. MAX. .120 (3.05) + CASE PIN 2 PIN 1 PIN 3 Negative CT Suffix "A" CASE PIN 2 Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Tc=125 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 8.0A Maximum DC Reverse Current Tc=25 C at Rated DC Blocking Voltage Tc=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: SF161 SF162 SF163 SF164 SF165 SF166 SF168 UNITS 50 35 50 100 70 100 150 105 150 200 140 200 16.0 125 0.95 10 500 35 -65 50 +150 50 1.30 1.70 300 210 300 400 280 400 600 420 600 V V V A A V µA µA nS pF C 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 56 RATING AND CHARACTERISTIC CURVES (SF161 THRU SF168) FIG.1- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50Ω NONINDUCTIVE 10Ω NONINDUCTIVE trr +0.5A FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT,(A) 24 20 16 12 8 4 0 0 25 50 75 100 125 150 175 Single Phase Half Wave 60Hz Resistive Or Inductive Load (+) 25Vdc (approx.) () 1Ω NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 -0.25A | | | | | | | | NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm CASE TEMPERATURE,( C) FIG.3-TYPICAL FORWARD CHARACTERISTICS 1000 50 INSTANTANEOUS FORWARD CURRENT,(A) FIG.4-TYPICAL REVERSE CHARACTERISTICS 3.0 F1 66 REVERSE LEAKAGE CURRENT, (µA) 10 100 Tc=100 C 61~ SF1 1.0 10 64 ~S SF 16 5 SF1 SF 1 68 Tj=25 C Pulse Width 300us 1% Duty Cycle Tc=25 C 0.1 1.0 .01 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 0.1 0 20 40 60 80 100 120 140 FORWARD VOLTAGE,(V) PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 125 FIG.6-TYPICAL JUNCTION CAPACITANCE 175 150 125 100 75 50 25 0 PEAK FORWARD SURGE CURRENT,(A) 100 75 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 50 25 0 1 5 10 50 100 JUNCTION CAPACITANCE,(pF) .01 .05 .1 .5 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz REVERSE VOLTAGE,(V) 57