SF305

SF301 30.0 AMP SUPER FAST RECTIFIERS THRU SF306 VOLTAGE RANGE 50 to 400 Volts CURRENT FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability * Good for switching mode application .120(3.05) DIA. .115(2.92) .180(4.53) .170(4.32) .840(21.34) .170(4.32) .150(3.81) 30.0 Amperes .635(16.13) TO-247 .205(5.21) .195(4.49) .625(15.88) .320(8.13) .310(7.87) 30 MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Lead solderable per MIL-STD-202, method 208 guranteed * Polarity: As Marked * Mounting position: Any * Weight: 5.60 grams .820(20.83) .12(3.0) .11(2.8) .095 (2.4) .800(20.32) .770(19.56) .050(1.27) .045(1.14) .225(5.7) .205(5.2) .030(0.8) .020(0.5) PIN 1 PIN 3 Positive CT Suffix "C" + CASE PIN 2 PIN 1 PIN 3 Negative CT Suffix "A" CASE PIN 2 Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Tc=100 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 15.0A Maximum DC Reverse Current Tc=25 C at Rated DC Blocking Voltage Tc=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: SF301 50 35 50 SF302 100 70 100 SF303 150 105 150 SF304 200 140 200 SF305 300 210 300 SF306 400 280 400 UNITS V V V A A V µA µA nS pF C 30.0 300 1.0 10 500 35 -65 120 +150 50 1.35 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 58 RATING AND CHARACTERISTIC CURVES (SF301 THRU SF306) FIG.1- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50Ω NONINDUCTIVE 10Ω NONINDUCTIVE trr +0.5A FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT,(A) 30 25 20 15 10 5 0 0 25 50 75 100 125 150 175 Single Phase Half Wave 60Hz Resistive Or Inductive Load (+) 25Vdc (approx.) () 1Ω NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 -0.25A | | | | | | | | NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm CASE TEMPERATURE,( C) FIG.3-TYPICAL FORWARD CHARACTERISTICS 1000 50 INSTANTANEOUS FORWARD CURRENT,(A) FIG.4-TYPICAL REVERSE CHARACTERISTICS REVERSE LEAKAGE CURRENT, (µA) 10 3.0 1.0 01~ SF3 04 06 100 Tc=100 C 10 05~ SF3 Tj=25 C Pulse Width 300us 1% Duty Cycle SF3 0.1 SF3 Tc=25 C 1.0 .01 0 .2 .4 .6 .8 1.0 1.2 1.4 0.1 0 20 40 60 80 100 120 140 FORWARD VOLTAGE,(V) PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 500 FIG.6-TYPICAL JUNCTION CAPACITANCE 175 150 125 100 75 50 25 0 PEAK FORWARD SURGE CURRENT,(A) 400 300 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 200 100 0 1 5 10 50 100 JUNCTION CAPACITANCE,(pF) .01 .05 .1 .5 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz REVERSE VOLTAGE,(V) 59