CDK3404CTQ48Y

Data Sheet A m p l i fy t h e H u m a n E x p e r i e n c e CDK3404 8-bit, 180MSPS, Triple Video DACs CDK3404 8-bit, 180MSPS, Triple Video DACs FEATURES n n n n n n n n General Description CDK3404 is a low-cost triple D/A converters that are tailored to fit graphics and video applications where speed is critical. CMOS-level inputs are converted to analog current outputs that can drive 25-37.5Ω loads corresponding to doubly-terminated 50-75Ω loads. A sync current following SYNC input timing is added to the IOG output. BLANK will override RGB inputs, setting IOG, IOB and IOR currents to zero when BLANK = L. Although appropriate for many applications, the internal 1.25V reference voltage can be overridden by the VREF input. Few external components are required, just the current reference resistor, current output load resistors, bypass capacitors, and decoupling capacitors. Package is a 48-lead TQFP. Fabrication technology is CMOS. Performance is guaranteed from -40°C to +125°C. 8-bit resolution, 180MSPS ±2.5% gain matching ±0.5% linearity error Sync and blank controls 1.0Vpp video into 37.5Ω or 75Ω load Internal bandgap voltage reference Low glitch energy Single +3.3V power supply APPLICATIONS n Video signal conversion – RGB – YCBCR – Composite, Y, C Multimedia systems Image processing PC Graphics n n n Block Diagram SYNC BLANK SYNC Rev 3A G7-0 8 8-bit D/A Converter IO G B7-0 8 8-bit D/A Converter IO B R7-0 CLOCK 8 8-bit D/A Converter IO R COMP R REF V REF +1.25V Ref Ordering Information Part Number CDK3404CTQ48 CDK3404CTQ48Y Package TQFP-48 TQFP-48 Pb-Free Yes Yes RoHS Compliant Yes Yes Operating Temp Range -40°C to +125°C -40°C to +125°C Packaging Method Package Quantity Tray Tray 250 1,250 Moisture sensitivity level for all parts is MSL-3. ©2009 CADEKA Microcircuits LLC www.cadeka.com Data Sheet Pin Configuration TQFP-48 GND R7 R6 R5 R4 R3 R2 R1 R0 GND GND NC CDK3404 8-bit, 180MSPS, Triple Video DACs 48 47 46 45 44 43 42 41 40 39 38 37 GND G0 G1 G2 G3 G4 G5 G6 G7 BLANK SYNC VDDD 1 2 3 4 5 6 7 8 9 10 11 12 36 35 34 33 32 31 30 29 28 27 26 25 TQFP CDK3404 RREF VREF COMP IOR IOG VDDA VDDA IOB GND GND CLOCK NC Pin Assignments Pin No. 26 47-40 9–2 23–16 Controls 11 10 Video Outputs 33 32 29 35 36 34 30, 31 12 1, 14, 15, 27, 28, 38, 39, 48 13, 24, 25, 37 IOR IOG IOB VREF RREF COMP VDDA VDDD GND Red Current Output Green Current Output Blue Current Output Voltage Reference Output/Input Current-Setting Resistor Compensation Capacitor Analog Power Supply Digital Power Supply Ground SYNC BLANK Sync Pulse Input Blanking Input Pin Name CLK R7-0 G7-0 B7-0 Description Clock Input Red Pixel Data Inputs Green Pixel Data Inputs Blue Pixel Data Inputs Clock and Pixel I/O NC GND GND B0 B1 B2 B3 B4 B5 B6 B7 NC 13 14 15 16 17 18 19 20 21 22 23 24 Rev 3A Voltage Reference Power and Ground NC No Connect ©2009 CADEKA Microcircuits LLC www.cadeka.com 2 Data Sheet Absolute Maximum Ratings The safety of the device is not guaranteed when it is operated above the “Absolute Maximum Ratings”. The device should not be operated at these “absolute” limits. Adhere to the “Recommended Operating Conditions” for proper device function. The information contained in the Electrical Characteristics tables and Typical Performance plots reflect the operating conditions noted on the tables and plots. CDK3404 8-bit, 180MSPS, Triple Video DACs Parameter Power Supply Voltage VDDA (Measured to GND) VDDD (Measured to GND) Digital Inputs Applied Voltage (measured to GND)(2) Forced Current(3,4) Analog Inputs Applied Voltage (measured to GND)(2) Forced Current Analog Outputs Applied Voltage (measured to GND)(2) Forced Current(3,4) Short Circuit Duration (single output in HIGH state to GND) (3,4) Min -0.5 -0.5 -0.5 -5.0 -0.5 -10.0 -0.5 -60.0 Max 4.0 4.0 VDDD + 0.5 5.0 VDDA + 0.5 10.0 VDD + 0.5 60.0 unlimited Unit V V V mA V mA V mA sec Reliability Information Parameter Temperature Operating, Ambient Junction Lead Soldering (10 seconds) Vapor Phase Soldering (1 minute) Storage Package Thermal Resistance (θJA) Notes: 1. Functional operation under any of these conditions is NOT implied. Performance and reliability are guaranteed only if Operating Conditions are not exceeded. 2. Applied voltage must be current limited to specified range. 3. Forcing voltage must be limited to specified range. 4. Current is specified as conventional current flowing into the device. 3 2.5 2 TQFP-48 Min -40 Max 125 150 300 220 150 65 Unit °C °C °C °C °C °C/W Rev 3A -65 CDK3404 Power Derating Maximum Power Dissipation (W) 1.5 1 0.5 0 -40 -20 0 20 40 60 80 100 120 Ambient Temperature (°C) Recommended Operating Conditions Symbol VDD VREF CC RL TA Parameter Power Supply Voltage Reference Voltage, External Compensation Capacitor Output Load Ambient Temperature, Still Air Min 3.0 1.0 Typ 3.3 1.25 0.1 37.5 Max 3.6 1.5 Unit V V µF Ω °C 3 -40 +125 ©2009 CADEKA Microcircuits LLC www.cadeka.com Data Sheet Electrical Characteristics (TA = 25°C, VDDA = VDDD =3.3V, VREF = 1.25V, RL = 37.5Ω, unless otherwise noted) Symbol IDD PD Parameter Power Supply Current Total Power Dissipation(2) Input Voltage, HIGH (1) Input Voltage, LOW (1) Input Current, HIGH Input Capacitance Output Current (1) (1) Conditions TA = 25°C (1) Min Typ 80 Max 85 95 300 Units mA mA TA = -40°C to +125°C (2) TA = -40°C to +125°C TA = -40°C to +125°C TA = -40°C to +125°C TA = -40°C to +125°C TA = -40°C to +125°C -1 -1 4 2.5 CDK3404 8-bit, 180MSPS, Triple Video DACs mW V Digital Inputs VIH VIL IIH IIL CI 0.8 1 1 V µA µA pF 30 40 7 TA = -40°C to +125°C 1.135 1.25 1.365 mA kΩ pF V Input Current, LOW (1) Analog Outputs RO CO VREF Output Resistance Output Capacitance Reference Voltage Output (1) Reference Output Notes: 1. 100% tested at 25°C. 2. Parameter is guaranteed (but not tested) by design and characterization data. Switching Characteristics (TA = 25°C, VDDA = VDDD =3.3V, VREF = 1.25V, RL = 37.5Ω, unless otherwise noted) Symbol Clock Input Conversion Rate (1) tPWH tPWL Pulse-width HIGH (2) Pulse-width LOW (2) Parameter Conditions TA = -40°C to +125°C TA = -40°C to +125°C TA = -40°C to +125°C TA = 25°C (1) TA = -40°C to +125°C TA = 25°C (1) TA = -40°C to +125°C (2) TA = -40°C to +125°C TA = -40°C to +125°C TA = -40°C to +125°C (2) Min Typ Max 180 Units MSPS ns ns ns ns Rev 3A 2 2 1.5 2 0.6 0.6 1.6 0.6 0.4 2.5 0.3 Data Inputs tS tH Setup Hold ns ns ns ns ns ns ns Data Outputs, with 50Ω doubly terminated load tD tR tF tSET tSKEW Notes: 1. 100% production tested at +25°C. 2. Parameter is guaranteed (but not tested) by design and characterization data. Clock to Output Delay Output Risetime Output Falltime Settling Time Output Skew ©2009 CADEKA Microcircuits LLC www.cadeka.com 4 Data Sheet DC Performance (TA = 25°C, VDDA = VDDD =3.3V, VREF = 1.25V, RL = 37.5Ω, unless otherwise noted) Symbol Parameter Resolution INL DNL Integral Linearity Error Differential Linearity Error Offset Error Gain Matching Error Absolute Gain Error TA = 25°C (1) Conditions Min 8 -0.5 -0.5 -0.5 (2) Typ Max 0.5 0.5 0.5 0.5 0.01 2.5 3.5 Units bits LSB LSB LSB LSB %FS %FS %FS mA mA mA CDK3404 8-bit, 180MSPS, Triple Video DACs TA = -40°C to +125°C (2) TA = 25°C (1) TA = -40°C to +125°C TA = -40°C to +125°C (2) TA = -40°C to +125°C (1) TA = -40°C to +125°C TA = 25°C (1) (1) -0.5 -2.5 -3.5 18.0 18.0 18.7 18.7 18.7 -0.01 0 19.4 19.4 Full-Scale Output Current TA = -40°C to +125°C (2) TA = -40°C to +125°C , With internal reference. Trim RSET to calibrate full-scale current. TA = -40°C to +125°C (2) PSRR Notes: Power Supply Rejection Ratio 0.01 %/% 1. 100% production tested at +25°C. 2. Parameter is guaranteed (but not tested) by design and characterization data. AC Performance (TA = 25°C, VDDA = VDDD =3.3V, VREF = 1.25V, RL = 37.5Ω, unless otherwise noted) Symbol Parameter Glitch Energy DAC-to-DAC Crosstalk Data Feedthrough Clock Feedthrough Notes: 1. 100% production tested at +25°C. 2. Parameter is guaranteed (but not tested) by design and characterization data. Conditions Min Typ 20 30 50 60 Max Units pVsec dB dB dB Analog Outputs Rev 3A ©2009 CADEKA Microcircuits LLC www.cadeka.com 5 Data Sheet Table 1. Output Voltage vs. Input Code, SYNC and BLANK, VREF = 1.25V, RREF = 348Ω, RL = 37.5Ω RGB7-0 (MSB…LSB) BLUE AND RED SYNC BLANK VOUT (V) SYNC GREEN BLANK VOUT (V) 1111 1111 1111 1111 1111 1110 1111 1101 • • 1000 0000 0111 1111 0111 1111 • • 0000 0010 0000 0001 0000 0000 0000 0000 XXXX XXXX XXXX XXXX 1 0 1 1 • • 1 1 0 • • 1 1 1 0 1 0 1 1 1 1 • • 1 1 1 • • 1 1 1 1 0 0 0.700 0.700 0.697 0.659 • • 0.351 0.349 0.349 • • 0.005 0.003 0.000 0.000 0.000 0.000 1 0 1 1 • • 1 1 0 • • 1 1 1 0 1 0 1 1 1 1 • • 1 1 1 • • 1 1 1 1 0 0 1.007 0.700 1.004 1.001 • • 0.658 0.656 0.349 • • 0.312 0.310 0.307 0.000 0.307 0.000 CDK3404 8-bit, 180MSPS, Triple Video DACs tPWL CLK tPWH 1/fs Rev 3A ts Pixel Data and Controls Data N tH Data N+1 Data N+2 3%/FS 90% tSET tF 10% tR tD OUTPUT 50% Figure 1. CDK3404 Timing Diagram ©2009 CADEKA Microcircuits LLC www.cadeka.com 6 Data Sheet Functional Description Within the CDK3404 are three identical 8-bit D/A converters, each with a current source output. External loads are required to convert the current to voltage outputs. Data inputs RGB7-0 are overridden by the BLANK input. SYNC = H activates, sync current from IOS for sync-on-green video signals. V DDA IOS SYNC G7-0 V DDA BLANK gates the D/A inputs. If BLANK = HIGH, the D/A inputs control the output currents to be added to the output blanking level. If BLANK = Low, data inputs and the pedestal are disabled. CDK3404 8-bit, 180MSPS, Triple Video DACs Data: 660mV max. Pedestal: 54mV Sync: 286mV V DDA B7-0 Figure 3. Normal Output Levels Sync Pulse Input - SYNC Bringing SYNC LOW, disables a current source which superimposes a sync pulse on the IOG output. SYNC and pixel data are registered on the rising edge of CLK. SYNC does not override any other data and should be used only during the blanking interval. If sync pulses are not required, SYNC should be connected to GND. Blanking Input - BLANK When BLANK is LOW, pixel data inputs are ignored and the D/A converter outputs are driven to the blanking level. BLANK is registered on the rising edge of CLK. V DDA R7-0 Figure 2. CDK3404 Current Source Structure Digital Inputs Incoming GBR data is regsitered on the rising edge of the clock input, CLK. Analog outputs follow the rising edge of CLK after a delay, tDO. Clock Input - CLK Pixel data is registered on the rising edge of CLK. CLK should be driven by a dedicated buffer to avoid reflection induced jitter, overshoot, and undershoot. Pixel Data Inputs - R7-0, B7-0, G7-0 RGB digital inputs are registered on the rising edge of CLK. Rev 3A D/A Outputs Each D/A output is a current source from the VDDA supply. Expressed in current units, the GBR transformation from data to current is as follows: G = G7-0 & BLANK + SYNC * 112 B = B7-0 & BLANK R = R7-0 & BLANK Typical LSB current step is 73.2µA. To obtain a voltage output, a resistor must be connected to ground. Output voltage depends upon this external resistor, the reference voltage, and the value of the gain-setting resistor connected between RREF and GND. To implement a doubly-terminated 75Ω transmission line, a shunt 75Ω resistor should be placed adjacent to the analog output pin. With a terminated 75Ω line connected to the analog output, the load on the CDK3404 current source is 37.5Ω. www.cadeka.com SYNC and BLANK SYNC and BLANK inputs control the output level (Figure 3 and Table 1, on the previous page) of the D/A converters during CRT retrace intervals. BLANK forces the D/A outputs to the blanking level while SYNC = L turns off a current source, IOS, that is connected to the green D/A converter. SYNC = H adds a 112/256 fraction of full-scale current to the green output. SYNC = L extinguishes the sync current during the sync tip. ©2009 CADEKA Microcircuits LLC 7 Data Sheet The CDK3404 may also be operated with a single 75Ω terminating resistor. To lower the output voltage swing to the desired range, the nominal value of the resistor on RREF should be doubled. R, G, and B Current Outputs - IOR, IOG, IOB Current source outputs can drive VESA VSIS, and RS343A/SMPTE-170M compatible levels into doubly-terminated 75Ω lines. Sync pulses can be added to the green output. When SYNC is HIGH, the current added to IOG is: IOS = 2.33 (VREF/ RREF) Current-Setting Resistor - RREF Full-scale output current of each D/A converter is determined by the value of the resistor connected between RREF and GND. Nominal value of RREF is found from: RREF = 5.31 (VREF/IFS) where IFS is the full-scale (white) output current (in amps) from the D/A converter (without sync). Sync is 0.439 * IFS. D/A full-scale (white) current may also be calculated from: IFS = VFS/RL Where VFS is the white voltage level and RL is the total resistive load (Ω) on each D/A converter. VFS is the blank to full-scale voltage. and GND. Voltage across RSET is the reference voltage, VREF, which can be derived from either the 1.25 volt internal bandgap reference or an external voltage reference connected to VREF. To minimize noise, a 0.1µF capacitor should be connected between VREF and ground. ISET is mirrored to each of the GBR output current sources. To minimize noise, a 0.1µF capacitor should be connected between the COMP pin and the analog supply voltage VDDA. Voltage Reference Output/Input - VREF An internal voltage source of +1.25V is output on the VREF pin. An external +1.25V reference may be applied to override the internal reference. Decoupling VREF to GND with a 0.1µF ceramic capacitor is required. CDK3404 8-bit, 180MSPS, Triple Video DACs Power and Ground Required power is a single +3.3V supply. To minimize power supply induced noise, analog +3.3V should be connected to VDDD and VDDA pins with 0.1µF and 0.01µF decoupling capacitors placed adjacent to each VDD pin or pin pair. The high slew-rate of digital data makes capacitive coupling to the outputs of any D/A converter a potential problem. Since the digital signals contain high-frequency components of the CLK signal, as well as the video output signal, the resulting data feedthrough often looks like harmonic distortion or reduced signal-to-noise performance. All ground pins should be connected to a common solid ground plane for best performance. Rev 3A Voltage Reference Full scale current is a multiple of the current ISET through an external resistor, RSET connected between the RREF pin ©2009 CADEKA Microcircuits LLC www.cadeka.com 8 Data Sheet Applications Dicussion Figure 5 (on the following page) illustrates a typical CDK3404 interface circuit. In this example, an optional 1.2V bandgap reference is connected to the VREF output, overriding the internal voltage reference source. 4. If the digital power supply has a dedicated power plane layer, it should not be placed under the CDK3404, the voltage reference, or the analog outputs. Capacitive coupling of digital power supply noise from this layer to the CDK3404 and its related analog circuitry can have an adverse effect on performance. 5. CLK should be handled carefully. Jitter and noise on this clock will degrade performance. Terminate the clock line carefully to eliminate overshoot and ringing. CDK3404 8-bit, 180MSPS, Triple Video DACs Grounding It is important that the CDK3404 power supply is wellregulated and free of high-frequency noise. Careful power supply decoupling will ensure the highest quality video signals at the output of the circuit. The CDK3404 has separate analog and digital circuits. To keep digital system noise from the D/A converter, it is recommended that power supply voltages come from the system analog power source and all ground connections (GND) be made to the analog ground plane. Power supply pins should be individually decoupled at the pin. Improved Transisiton Times Output shunt capacitance dominates slowing of output transition times, whereas series inductance causes a small amount of ringing that affects overshoot and settling time. With a doubly terminated 75Ω load, transition times can be improved by matching the capacitive impedance output of the CDK3404. Output capacitance can be matched with a 220nH inductor in series with the 75Ω source termination. IOG 32 W1 COAX R1 75Ω Printed Circuit Board Layout Designing with high-performance mixed-signal circuits demands printed circuits with ground planes. Overall system performance is strongly influenced by the board layout. Capacitive coupling from digital to analog circuits may result in poor D/A conversion. Consider the following suggestions when doing the layout: 1. Keep the critical analog traces (VREF, IREF, COMP, IOS, IOR, IOG) as short as possible and as far as possible from all digital signals. The CDK3404 should be located near the board edge, close to the analog out-put connectors. 2. The power plane for the CDK3404 should be separate from that which supplies the digital circuitry. A single power plane should be used for all of the VDD pins. If the power supply for the CDK3404 is the same as that of the system’s digital circuitry, power to the CDK3404 should be decoupled with 0.1µF and 0.01µF capacitors and isolated with a ferrite bead. 3. The ground plane should be solid, not cross-hatched. Connections to the ground plane should have very short leads. U1 CDK3404 IOB 29 W2 COAX R2 75Ω Rev 3A IOR 33 W3 COAX R3 75Ω L1 220nH R4 75Ω L2 220nH R5 75Ω L3 220nH R6 75Ω Figure 4. Schematic, Transition Time Sharpening Circuit A 220nH inductor trims the performance of a 4ft cable, quite well. In Figures xx through xx, the glitch at 12.5ns, is due to a reflection from the source. Not shown, are smaller glitches at 25 and 37.5ns, corresponding to secondary and tertiary reflections. Inductor values should be selected to match the length and type of the cable. ©2009 CADEKA Microcircuits LLC www.cadeka.com 9 Data Sheet 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -0.1 -5 0 5 10 15 20 0.8 0.7 0.6 0.5 0.4 0.3 GOUT (V) ROUT (V) CDK3404 8-bit, 180MSPS, Triple Video DACs 0.2 0.1 0 -0.1 -0.2 -5 0 5 10 15 20 Time (ns) Time (ns) Figure 5. Unmatched tR 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -0.1 -5 0 5 10 15 20 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -5 Figure 7. Unmatched tF GOUT (V) GOUT (V) 0 5 10 15 20 Time (ns) Time (ns) Figure 6. Matched tR +3.3V Figure 8. Matched tF Rev 3A 0.1µF 0.01µF 10µF 0.1µF VDDD GND VDDA RED PIXEL INPUT GREEN PIXEL INPUT BLUE PIXEL INPUT CLOCK SYNC BLANK IOR IOG 75Ω 75Ω 75Ω COMP 0.1µF V REF R REF VDDA Red Zo = 75Ω 75Ω 75Ω 75Ω R7-0 G7-0 B7-0 CLK SYNC BLANK Green w/Sync Zo = 75Ω Blue Zo = 75Ω CDK3404 Triple 8-bit D/A Converter IOB (not required without external reference) 3.3kΩ LM185-1.2 348Ω (Optional) 0.1µF Figure 9. Typical Interface Circuit Diagram Evaluation boards are available (CEB3400), contact CADEKA for more information. Related Products n n CDK3400/3401 Triple 10-bit 180MSPS DACs CDK3404 Triple 8-bit 180MSPS DAC www.cadeka.com ©2009 CADEKA Microcircuits LLC 10 Data Sheet Mechanical Dimensions LQFP-48 Package CDK3404 8-bit, 180MSPS, Triple Video DACs Rev 3A For additional information regarding our products, please visit CADEKA at: cadeka.com CADEKA Headquarters Loveland, Colorado T: 970.663.5452 T: 877.663.5452 (toll free) CADEKA, the CADEKA logo design, COMLINEAR and the COMLINEAR logo design are trademarks or registered trademarks of CADEKA Microcircuits LLC. All other brand and product names may be trademarks of their respective companies. CADEKA reserves the right to make changes to any products and services herein at any time without notice. CADEKA does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by CADEKA; nor does the purchase, lease, or use of a product or service from CADEKA convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual property rights of CADEKA or of third parties. Copyright ©2009 by CADEKA Microcircuits LLC. All rights reserved. A m p l i fy t h e H u m a n E x p e r i e n c e