TMC22191R0C

www.cadeka.com TMC22091/TMC22191 Digital Video Encoders/Layering Engine Features • All-digital video encoding • Internal digital oscillators, no crystals required • Multiple input formats supported – 24-bit and 15-bit GBR/RGB – YCBCR422 or 444 – Color indexed • 30 overlay colors (TMC22191) • Fully programmable timing • Supports input pixel rates of 10 to 15 Mpps • 256 x 8 x 3 color look-up tables (bypassable on TMC22191) • 8-bit mask register • 8-bit composite digital video input • Hardware and 24-bit data keying • Synchronizes with TMC22071 Genlocking Video Digitizer • 8:8:8 video reconstruction • SMPTE 170M NTSC or CCIR Report 624 PAL compatible • Supports PAL-M and NTSC without pedestal • Simultaneous S-VIDEO (Y/C) NTSC/PAL output • 10-bit D/A conversion (three channels) • • • • • • • Controlled edge rates 3 power-down modes Built-in color bars and modulated ramp test signals JTAG (IEEE Std 1149.1-1990) test interface Single +5V power supply 84 lead PLCC package 100 lead MQFP package Description The TMC22x91 digital video encoders convert digital computer image or graphics data (in RGB, YCBCR, or color indexed format) or a CCIR-601 signal into a standard analog baseband television (NTSC or PAL) signal with a modulated color subcarrier. Both composite (single lead) and S-VIDEO (separate chroma and luma) formats are active simultaneously at the three analog output pins, each of which generates a standard video-level signal into doubly-terminated 75Ω load. The TMC22x91 accepts digitized video from the companion TMC22071 Genlocking Video Digitizer. Soft switching between video sources is done under either hardware or programmable data control. The TMC22191 offers 4-layer keying capability, bypassable CLUT, and 30 Overlay colors. The TMC22x91 is fabricated in a submicron CMOS process and packaged in an 84 Lead Plastic Leadless Chip Carrier, or in a 100 Lead Metric Quad Flat Pack. Performance is guaranteed from 0°C to 70°C. Logic Symbol BYPASS and OL4:0 on TMC22191 only. PD23-0 FRAME BUFFER INTERFACE 24 6 VIDEO OUTPUT OL4-0 PDC VHSYNC VVSYNC KEY BYPASS CVBS7-0 GHSYNC GVSYNC CHROMA LUNA COMPOSITE ANALOG INTERFACE GENLOCK INTERFACE 8 TMC22x91 DIGITAL VIDEO ENCODER VREF COMP RREF JTAG TEST INTERFACE MICROPROCESSOR INTERFACE TDI TMS TCK TDO RESET D7-0 A1-0 CS R/W 8 2 CLOCKS LDV PXCK 27008A Rev. 1.1.0 TMC22091/TMC22191 PRODUCT SPECIFICATION Block Diagram OL4-0 FRAME BUFFER INTERFACE BYPASS G/R/Y MAP PD23-0 FORMATTER B/G/CB MASK, KEY COMPARATOR R/B/CR Data Key KEY PDC VVSYNC VHSYNC R/R-Y 256 x 8 x 3 COLOR B/B-Y LOOK-UP TABLE G/Y R-Y INTERPOLATOR 4:2:2/4:4:4 MATRIX B-Y LPF SYNC, BLANK INSERT LPF CHROMA MODULATOR INT 10-bit D/A LUMA INT 10-bit D/A CHROMA ENCODED VIDEO OUTPUT ANALOG INTERFACE BYPASS and OL4:0 on TMC22191 only. GHSYNC GENLOCK INTERFACE GVSYNC DIGITAL SYNC. GEN. SUBCARRIER SYNTHESIZER INT VIDEO SWITCH 10-bit D/A COMPOSITE CVBS7-0 INTERPOLATION FILTERS D/A REF. CLOCK CONTROL JTAG VREF COMP RREF LDV PXCK RESET D7:0 A1:0 CS R/W TDI TMS TCK TDO JTAG TEST INTERFACE CLOCKS MICROPROCESSOR INTERFACE 27006A Functional Description The TMC22091 and TMC22191 are totally integrated, fullyprogrammable digital video encoders with simultaneous composite and Y/C (S-VIDEO) outputs. The TMC22x91 video outputs are compatible with SMPTE 170M NTSC, CCIR Report 624 PAL, PAL-M, and NTSC without pedestal television standards. No external component selection or tuning is required. The encoders accept digital image data at the PD port in one of several formats, which are matrixed into luminance and chrominance components. The chrominance signals are modulated onto a digitally synthesized subcarrier. The luminance and chrominance signals are separately interpolated to twice the pixel rate, and converted to analog levels by 10-bit D/A converters. They are also digitally combined and the resulting composite signal is output by a third 10-bit D/A converter. This composite signal may be keyed (pixel rate switching) with a second composite digital video signal presented to the encoder. The output video frames may be internally timed by the TMC22x91, synchronized with the external frame buffer, or slaved to the companion Genlocking Video Digitizer (TMC22071). All operational parameters are fully programmable over a standard microprocessor port. Table 1 shows the key features that distinguish between the TMC22091 and TMC22191. All of the information presented in this data sheet applies to both products unless otherwise noted. Statements, paragraphs, tables, and figures that apply to only one or two of the encoders have notation specifying the applicable part number. 2 Timing The encoder operates from a single clock at twice the system pixel rate. This frequency may be set between 20 MHz and 36 MHz (pixel rates of 10 Mpps to 18 Mpps). Within this range are included CCIR-601, D2, and square-pixel formats, as well as a variety of computer-specific pixel rates. An array of programmable timing registers allows the software selection of all pertinent signal parameters to produce NTSC (with or without 7.5 IRE pedestal) and PAL, and PAL-M outputs. Table 1. Comparing the TMC22x91 Encoders Feature OL4-0 pixel inputs for 30 overlay colors Number of video layers supported BYPASS input for bypassing CLUTs TMC22091 TMC22191 No 2 No Yes 4 Yes Input Formatting The input section accepts a variety of video and graphics formats, including 24-bit GBR and RGB, 15-bit GBR and RGB, YCBCR422, YCBCR444, and 8-bit color-indexed data (Figure 1a and 1b). The input section of the TMC22x91 includes a key comparator which monitors the pixel data port with three independent 8-bit comparators, and invokes a video key when the selected registers match the incoming data. PRODUCT SPECIFICATION TMC22091/TMC22191 Mask Register A Mask Register is provided which is logically ANDed with incoming color-index data to facilitate pixel animation and other special graphics effects. The Mask Register is ahead of the Data Key comparators and is enabled only when colorindex input is selected. Mask Register programming and operation are similar to that of the 171/176 family of graphics RAMDACS. Colorspace Conversion Matrix and Interpolator The matrix converts RGB data (whether from RGB inputs or color-indexed CLUT data) into Y, B-Y, R-Y format for encoding. In input configurations where the pixel input is already in Y, B-Y, R-Y format, the matrix is bypassed. When pixel data is input in YCBCR422 format, the interpolation filters produce YCBCR444 for encoding. Color Lookup Table The Color Lookup Table (CLUT) is a 256 x 8 x 3 randomaccess memory. It provides means for offset, gain, gamma, and color correction in RGB and YCBCR operating modes. It provides a full 24-bit color lookup function for color-index mode. It can be loaded in the same manner as a standard VGA RAMDAC. Sync Generator The TMC22x91 can operate in Master, Genlock, or Slave modes. In Master and Genlock modes, the encoder internally generates all timing and sync signals, and provides Horizontal Sync, Vertical Sync, and Pixel Data Control (PDC) to the external frame buffer circuitry. PDC is independently selectable to function as an input or an output. In Genlock mode, the TMC22x91 timing is controlled by the TMC22071 Genlocking Video Digitizer over the CVBS7-0 bus, GVSYNC, and GHSYNC. The encoder, in turn, produces VHSYNC, VVSYNC, and PDC for the frame buffer interface. MODE GBR444 MSB 23 G7 16 15 8 7 LSB 0 Format Control Register MSB LSB G R Y Y G0 B7 B G CB CB/CR B 0 R7 R B CR R0 00011000 RGB444 R7 Y7 R0 G7 Y0 CB7 CB7 Y0 CR7 G0 B 7 CB0 RR7 CB0 CR0 B0 RR0 00010000 YCBCR444 00011100 YCBCR422 Y7 00011101 COLOR INDEX P7 Pixel B0 R4 P0 0001X011 GBR15 G4 G R G0 B 4 B G R B R0 00011010 RGB15 R4 R 0 G4 G 0 B4 B0 24300A 00010010 Figure 1a. Pixel Data Format 3 TMC22091/TMC22191 PRODUCT SPECIFICATION MODE GBR444 MSB 23 G7 16 15 8 7 LSB 0 Format Control Register MSB LSB G R Y Y Pixel R G R0 G0 B7 B G CB CB* Pixel G B G0 B 0 R7 R B CR CR* Pixel B R B0 R0 01011000 RGB444 R7 R0 G 7 G0 B7 B0 01010000 YCBCR444 Y7 Y0 CB7 CB0 CR7 CR0 0101X000 YCBCR422 Y7 Y0 CB7 CB0 CR7 CR0 0101X001 COLOR INDEX P7 P0 P7 P0 P7 P0 0101X011 RGB15 R4 G4 B4 01010010 GBR15 G4 G0 B4 B0 R4 R0 24393A 01011010 *CB and CR are loaded on alternate LDV cycles Figure 1b. Pixel Data Format (TMC22191 when CLUTs are Bypassed) In Slave mode, VHSYNC, VVSYNC, and PDC (optional) are inputs to the TMC22x91. These inputs determine when new lines, frames, and active picture areas begin. The external controlling circuitry needs to establish the correct timing for these signals. Horizontal and vertical synchronization signals are digitally generated by the TMC22x91 with controlled rise and fall times on all sync edges, the beginning and end of active video, and the burst envelope. All elements of horizontal sync timing are programmable, as are the frequency, phase, and duration of color burst. An interpolation filter on the CVBS data similarly raises the sample rate of the video signal, for mixing with the encoded pixel data. Composite Video Switch The Composite Video Switch selects between the composite video input (CVBS) and the composite encoded pixel data on a pixel-by-pixel basis, under the control of a key function. Keying may be managed by hardware or software. The hardware key input (KEY pin) directly controls the video switch. The encoder may be programmed to operate with a data key, represented by three 8-bit registers that compare with the 24 input bits. They operate in all input modes and may be individually enabled or disabled. Video Input The TMC22x91 accepts genlocked synchronization data and digital composite video signals from the TMC22071 Genlocking Video Digitizer over the 8-bit CVBS bus. The encoder synchronizes its digital subcarrier oscillator to the video input from the TMC22071 with this data. The composite video data output from the TMC22071 is passed to the internal video switch for keying with the encoded pixel data. D/A Converters The analog outputs of the TMC22x91 are the outputs of three 10-bit D/A converters, operating at twice the pixel clock rate. The outputs are capable of driving standard video levels into a doubly-terminated 75Ω coaxial video cable (37.5Ω total load). An internal voltage reference is provided which can be used to provide reference current for the three D/A converters. For accurate video levels, an external fixed or variable voltage reference source is recommended. The video signal levels from the TMC22x91 may be adjusted to overcome the insertion loss of analog low-pass output filters. The D/A converters on the TMC22x91 may be powereddown via Control Register 0E bits 5 and 6. The COMPOSITE D/A is controlled by bit 6 and the LUMA and CHROMA D/A converters are controlled by bit 5. Chroma Modulator A 32-bit digital subcarrier synthesizer feeds a quadrature modulator, producing a digital chrominance signal. The relative phases of the burst and active video portions of the subcarrier can be individually adjusted to compensate for external phase errors and to effect a hue control. Interpolation Filters Interpolation filters on the luminance and chrominance signals double the pixel rate in preparation for D/A conversion. This band-limited process greatly simplifies the output filtering required following the D/A converters and dramatically reduces sin(x)/x distortion. 4 PRODUCT SPECIFICATION TMC22091/TMC22191 Microprocessor Interface The microprocessor interface employs a 13 line format. The RESET pin sets all internal state machines to their initialized conditions, disables the analog outputs, sets the internal SRESET bit LOW (reset condition), and places the encoder in a power-down mode. All register and CLUT data are maintained in power-down mode. If the HRESET bit is set HIGH, line 1 field 1 is started when RESET goes HIGH, and SRESET is ignored. If HRESET is LOW, the encoder remains idle after RESET goes HIGH until Control Register bit SRESET is set HIGH, which initiates line 1 field 1. Two address lines are provided and decoded for access to the internal Control Registers and CLUT. Control Registers and CLUT are accessed by loading a desired address through the 8-bit D7-0 port, followed by the desired data read or write for that address. Both the CLUT and the Control Registers are self-indexing, allowing continuous reads or writes to successive addresses. bars are useful as an idle system output signal. The test signals may be used to verify proper operation of the analog video signal chain. TMC22090/TMC22190 Compatibility The TMC22090 and TMC22190 are earlier versions of the TMC22091 and TMC22191, respectively. They lack the following features of the newer versions: 1. 2. 3. 4. 5. Selectable Setup (to support NTSC EIA-J video output for Japan) PAL-M format (for South American applications) Extended EH and SL intervals (to support pixel rates above 15 Mpps) Individual D/A power-down (to reduce total dissipation when some outputs are not required) Luminance I/O processing (to reduce flicker in graphics applications) JTAG Test Interface The TMC22x91 includes a standard 4-line JTAG (IEEE Std 1149.1-1990) test interface port, providing access to all digital input/output data pins. This is provided to facilitate component and board-level testing. These features are controlled by registers 0E and 0F, and enabled by setting Register OE bit 7 to ONE. If an application of the TMC22x90 is programmed with this bit set to ZERO (as recommended in the product documentation) then the corresponding TMC22x91 will perform identically. Though the earlier parts continue to be available, it is recommended that the newer devices be used in new designs for the additional flexibility. Older designs may be readily converted to the newer versions to take advantage of the added features and lower cost of the later technology. Test/Validation Mode The TMC22x91 may be configured to produce standard color bars or a 40 IRE modulated (or unmodulated) video ramp, independent of any pixel or video data input. Color 5 TMC22091/TMC22191 PRODUCT SPECIFICATION Pin Assignments 84 Lead PLCC 1 84 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Name CVBS2 CVBS1 CVBS0 KEY RESET CS R/W A1 A0 DGND PDC VHSYNC VVSYNC D7 D6 D5 D4 D3 D2 D1 D0 Pin 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Name TDO TCK TMS TDI DGND VDD BYPASS (TEST) OL4 (TEST) VREF RREF AGND COMPOSITE AGND LUMA AGND CHROMA AGND COMP VDDA VDDA VDDA Pin 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Name VDDA CVBS7 CVBS6 CVBS5 CVBS4 OL3 (TEST) OL2 (TEST) OL1 (TEST) OL0 (TEST) PD23 PD22 PD21 PD20 PD19 PD18 PD17 PD16 PD15 PD14 PD13 PD12 Pin 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 Name VDD DGND PD11 PD10 PD9 PD8 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 LDV PXCK DGND VDD GVSYNC GHSYNC CVBS3 65-3751-01 Note: Pin names in parentheses apply to TMC22091. 100 Lead MQFP Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Name NC COMPOSITE NC AGND LUMA AGND NC CHROMA AGND COMP NC NC VDDA VDDA VDDA VDDA VDDA CVBS7 CVBS6 CVBS5 CVBS4 OL3 (TEST) OL2 (TEST) OL1 (TEST) OL0 (TEST) Pin 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Name PD23 PD22 NC NC NC PD21 PD20 PD19 PD18 PD17 PD16 PD15 PD14 PD13 PD12 VDD DGND PD11 PD10 PD9 PD8 PD7 PD6 PD5 PD4 Pin 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 Name PD3 NC NC NC NC PD2 PD1 PD0 LDV PXCK DGND VDD GVSYNC GHSYNC CVBS3 CVBS2 CVBS1 CVBS0 NC KEY RESET CS R/W A1 A0 Pin 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Name DGND PDC NC NC VHSYNC VVSYNC D7 D6 D5 D4 D3 D2 D1 D0 TDO TCK TMS TDI DGND VDD BYPASS (TEST) OL4 (TEST) VREF RREF AGND 100 1 65-3751-02 Note: Pin names in parentheses apply to TMC22091. 6 PRODUCT SPECIFICATION TMC22091/TMC22191 Pin Descriptions Pin Number Pin Name Clocks PXCK 79 60 TTL Master Clock Input. This 20 to 30 MHz clock is internally divided by 2 to generate the internal pixel clock, PCK, which a LOW on RESET forces LOW. PXCK drives the entire TMC22x91, except the asynchronous microprocessor interface and the semi-synchronous LDV data input clock. All internal registers are strobed on the rising edge of PXCK. Pixel Data Load Clock. On each rising edge of LDV, data on PD23-0 are latched into the input preload register, for transfer into the input demultiplexer on the next rising edge of PCK. Pixel Data Inputs. In YCBCR, GBR, RGB, and color-indexed mode, pixel data enter the TMC22x91 on PD23-0. The specific format is found in Figures 1a and 1b. LDV is the clock that controls the loading of pixel data. Horizontal Sync I/O. In Master and Genlock modes, the TMC22x91 outputs horizontal sync on this pin. In Slave modes, the TMC22x91 accepts and locks to horizontal sync input on this pin (with vertical sync on VVSYNC). VHSYNC and VVSYNC must be coincident since they are clocked into the TMC22x91 on the same rising edge of PXCK. Vertical Sync I/O. In separate V and H sync Master and Genlock modes, the TMC22x91 outputs vertical block sync (VVSYNC LOW for the 2.5 (PAL) or 3 (NTSC) lines on which vertical sync pulses occur). In composite sync (H and V sync on same signal) Master and Genlock modes, the TMC22x91 outputs horizontal sync, vertical sync, and equalization over this pin. In Slave mode, the TMC22x91 accepts and locks to vertical sync input on this pin (with horizontal sync on VHSYNC). VHSYNC and VVSYNC must be coincident such that they are clocked into the TMC22x91 on the same rising edge of PXCK. Pixel Data Control. In Master mode, the TMC22x91 forces PDC HIGH when and only when it wants active video from the frame buffer. During blanking (syncs, equalization, burst, and porches), it forces PDC LOW, signaling that it will ignore any data presented over PD23-0. When PDC is used as an input, forcing it HIGH allows the TMC22x91 to receive PD during the active video state. Hardware Key Input. When the HKEN control bit is set HIGH and hardware key pin, KEY, is HIGH, video data entering on CVBS7-0 are routed to the COMPOSITE output. This control signal is pipelined so the pixel that is presented to the PD port when the KEY signal is invoked is at the midpoint of the soft key transition. When HKEN is LOW, KEY is ignored. Like PD data, KEY is clocked into the TMC22x91 on the rising edge of LDV. 84-Lead 100-Lead PLCC MQFP Value Pin Function Description LDV 78 59 TTL Frame Buffer Interface PD23-0 52-63, 66-77 26, 27, 31-40, 43-51, 56-58 80 TTL VHSYNC 12 TTL VVSYNC 13 81 TTL PDC 11 77 TTL KEY 4 70 TTL 7 TMC22091/TMC22191 PRODUCT SPECIFICATION Pin Descriptions (continued) Pin Number Pin Name OL4-0 84-Lead 100-Lead PLCC MQFP 29, 48-51 97, 22-25 Value TTL Pin Function Description Overlay Data Inputs (TMC22191 only). 30 of the 256 locations of the CLUT may be reserved for overlay operation. These CLUT locations are directly accessed by five input pins, OL4-0. OL4-0 are entered into the TMC22191 on a pixel-bypixel basis and select which of the 30 overlay colors is to be encoded. When all five OL4-0 inputs are LOW, no overlay occurs. CLUT Bypass Control (TMC22191 only). When BYPASS is HIGH, the CLUT is in the pixel data path within the TMC22191. When BYPASS is LOW, pixel data bypasses the CLUT. BYPASS is active only for certain modes of the Layering Control Register (LCR) when the Format Control Register bit 6 is HIGH. Genlock Horizontal Sync. In Genlock mode, the TMC22x91 will start a new horizontal line (blank-to-sync-edge transition) with each falling edge of GHSYNC. In non-genlock modes, the TMC22x91 ignores GHSYNC. The internal pixel clock, PCK, is aligned with the falling edge of VHSYNC or GHSYNC (Genlock mode). Genlock Vertical Sync. In Genlock mode, the TMC22x91 will start a new vertical sync sequence at line 1 field 1 whenever GVSYNC and GHSYNC are coincident such that they are clocked into the TMC22x91 on the same rising edge of PXCK. If GVSYNC falls at any other time, the TMC22x91 will assume that this marks the start of field 2, and will ignore it (in odd-field sync mode) or (in all-field sync mode) respond by generating a single vertical sync pulse, followed by 2 (PAL) or 2.5 (NTSC) lines of vertical sync, keyed to the next falling edge on GHSYNC. See Interface Control Register bit 0 for odd-field and all-field operation. Composite Video Inputs. The encoder receives digitized video, subcarrier phase, and subcarrier frequency over this 8bit bus at the PCK rate. This data may be provided by the companion TMC22071 Genlocking Video Digitizer. In Genlock mode, the TMC22x91 expects subcarrier phase and frequency data during each line’s horizontal sync interval, as well as video data when keying is engaged, transferred at the PCK rate. Data I/O Port. All control parameters are loaded into and read back over this 8-bit port. For digital testing, the five lower bits can also serve as a two-cycle 10-bit data output port. For D/A converter testing, it can be used as a 10-bit two-cycle input port, facilitating, for example, ramp-based D/A converter linearity tests. µProc Port Controls. As in a RAMDAC, this control governs whether the microprocessor interface selects a table address or reads/writes table contents. It also governs setting and verification of the TMC22x91’s internal operating modes, also over port D7-0. BYPASS 28 96 TTL Genlock Interface GHSYNC 83 64 CMOS GVSYNC 82 63 CMOS CVBS7-0 44-47, 84, 1-3 18-21, 65-68 TTL Microprocessor Interface D7-0 14-21 82-89 TTL A1-0 8-9 74-75 TTL 8 PRODUCT SPECIFICATION TMC22091/TMC22191 Pin Descriptions (continued) Pin Number Pin Name CS 84-Lead 100-Lead PLCC MQFP 6 72 Value TTL Pin Function Description Chip Select. When CS is HIGH, the microprocessor interface port, D7-0, is set to HIGH impedance and ignored. When CS is LOW, the microprocessor can read or write parameters over D7-0. One additional falling edge of CS is needed to move input data to its assigned working registers. Bus Read/Write Control. When R/W and CS are LOW, the microprocessor can write to the control registers or CLUT over D7-0. When R/W is HIGH and CS is LOW, it can read the contents of any CLUT address or control register over D7-0. Master Reset Input. Bringing RESET LOW sets the software reset control bit, SRESET, LOW, forcing the internal state machines to their starting states and disabling all outputs. Bringing RESET HIGH synchronizes the internal pixel clock (PCK = PXCK / 2) to maintain a defined pipeline delay through the TMC22x91. If HRESET is set HIGH, the encoder is enabled when RESET goes HIGH. If HRESET is LOW, the host restarts the TMC22x91 by setting SRESET HIGH. RESET does not affect the CLUT or the control registers, except SRESET. NTSC/PAL Video. Analog output of composite D/A converter, nominally 1.35 volt peak-to-peak into a 37.5Ω load. Luminance-only Video. Analog output of luminance D/A converter, nominally 1.35 volt peak-to-peak into a 37.5Ω load. Chrominance-only Video. Analog output of chrominance D/A converter, nominally 1.35 volt peak-to-peak into a 37.5Ω load. Voltage Reference Input. External voltage reference input, internal voltage reference output, nominally 1.235 V. Compensation Capacitor. Connection point for 0.1µf decoupling capacitor. Current-setting Resistor. Connection point for external current-setting resistor for D/A converters. The resistor (392Ω) is connected between RREF and AGND. Output video levels are inversely proportional to the value of RREF. Data Input Port. Boundary scan data input port. Scan Select Input. Boundary scan (HIGH)/normal operation (LOW) selector. Scan Clock Input. Boundary scan clock. Data Output Port. Boundary scan data output port. Positive digital power supply. Positive analog power supply. Digital Ground. Analog Ground. R/W 7 73 TTL RESET 5 71 TTL Video Output COMPOSITE LUMA CHROMA Analog Interface VREF COMP RREF 30 39 31 98 10 99 +1.23 V 0.1 µF 392Ω 33 35 37 2 5 8 1 V P-P 1 V P-P 1 V P-P JTAG Test Interface TDI TMS TCK TDO Power Supply VDD VDDA DGND AGND 27, 64, 81 41, 62, 95 40-43 13-17 10, 26, 65, 42, 61, 76, 80 94 32, 34, 36, 38 4, 6, 9, 100 +5 V +5 V 0.0 V 0.0 V 25 24 23 22 93 92 91 90 TTL TTL TTL TTL 9 PRODUCT SPECIFICATION TMC22091/TMC22191 Pin Descriptions (continued) Pin Number Pin Name Test TEST 28, 29, 48-51 22-25, 96-97 0.0 V Factory testing (TMC22091 only). Reserved for factory testing. These pins have no effect on the operation but do function as JTAG registers. They should be grounded directly or pulled down to ground with 1kΩ or smaller resistors. No Connect 84-Lead 100-Lead PLCC MQFP Value Pin Function Description NC N/A 1, 3, 7, 11-12, 28-30, 52-55, 69, 78-79 Control Registers The TMC22x91 is initialized and controlled by a set of registers. The registers are organized into 13 categories: 1. 2. 3. 4. 5. 6. 7. 8. 9. Global Control Format Control Interface Control Test Control Key Control Misc. Control Standards Control Layering Control (TMC22191) Key Value contents or those of the Control Registers. The port is governed by pins CS, R/W, and A1-0. The Address Register for the CLUT and the Control Register pointer automatically increment to allow successive writes to sequential addresses. In the CLUT, the Address Register has two additional bits which increment in modulo-three to sequentially access the red, green, and blue portions. All three colors must be written when any CLUT address is changed. The control register autoincrement follows the sequence indicated in the Control Register Map. When it reaches address 40, it stops incrementing, allowing multiple reads or writes of test data from/to the TESTDAT register. To exit the test mode, reset the Control Register pointer by setting A1-0, D7-0, and R/W LOW and then bring CS LOW. Address 1F is a read-only status register. It is addressed by the autoincrement sequencer. Any data may be written into this port at that time but it will not be stored. When address 50 is accessed, no autoincrement takes place, allowing multiple writes to the Mask Register. 10. Timing 11. Subcarrier 12. Test I/O 13. Mask Register An external controller loads the Control Registers through a standard interface port. It also loads the CLUT and reads its 10 PRODUCT SPECIFICATION TMC22091/TMC22191 Table 2. Microprocessor Port Control A1-0 00 00 01 01 10 10 11 11 R/W 0 1 0 1 0 1 0 1 Action Write D7-0 into Control Register pointer Read Control Register pointer on D7-0 Write D7-0 into CLUT Address Pointer Read CLUT Address Pointer on D7-0 Write D7-0 to addressed Control Register Read addressed Control Register on D7-0 Write D7-0 to addressed CLUT location Read addressed CLUT location on D7-0 Table 3. Control Register Map (continued) Reg 02 02 02 03 03 03 03 03 03 03 03 Bit 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3-1 0 7-0 7-0 HKEN BUKEN SKEXT DKDIS EKDIS FKDIS SKEN LAYMODE HKEN BUKEN SKEXT LAYMODE SKEN DKEY EKEY LIMEN TESTEN HOLDEN TSTMSB LUMTST 8FSUBR CHRTST Name FBDIS PDCDIR FLDLK Function Frame buffer signals disable PDC master, slave select Field lock select Reserved Luminance limiter enable Test enable MSBs/LSBs hold select LSBs, MSBs in/out select LUMA channel test 8-field subcarrier reset enable CHROMA channel test Reserved Hardware key enable Burst key enable Data key operation select Green/red/Y data key disable Blue/green/CB data key disable Red/blue/CR data key disable Data key enable MSB of Layer Assignments select Hardware key enable Burst key enable Data key operation select LSBs of Layer Assignments select Data key enable Green/red/Y data key value Blue/green/CB data key value Test Control Register Table 3. Control Register Map Reg 00 00 00 00 00 00 01 01 Bit 7-5 4 3 2 1 0 7 6 LCREN SRESET PAL LUMDIS CHRDIS HRESET Name Function Reserved Software reset Standard select, NTSC or PAL Luminance input disable Chrominance input disable Software reset disable Reserved Layering Control Register enable (TMC22191) Modulated ramp test Color bar test PD23-0 input format select PD23-0 input mode select VITS lines enable Short-cycle test mode Time-base source select Sync output mode select Key Control Register 04 04 04 04 04 04 04 04 04 04 04 04 04 04 05 06 Global Control Register Format Control Register Layering Control Register (TMC22191) 01 01 01 01 5 4 3-2 1-0 RAMPEN CB FORMAT INMODE Interface Control Register 02 02 02 02 7 6 5-4 3 VITSEN SHCY TBASE SOUT Key Value Registers 11 TMC22091/TMC22191 PRODUCT SPECIFICATION Table 3. Control Register Map (continued) Reg 07 08-0D Misc. Control Register 0E 0E 0E 0E 0E 0E 0E 0E 0F 0F 0F 0F 0F 0F 7 6 5 4 3 2 1 0 7 6 5 4 3-2 1-0 EFEN COMPD/A SVIDD/A FKREN RATIO TFLK T512 CB100 EFEN SIX25 PALID SETUP YGAIN CGAIN Register 0E and 0F enable COMPOSITE D/A disable LUMA/CHROMA D/A disable Luminance processing enabled Luminance ratio select Luminance pass threshold select EH/SL offset select NTSC/PAL Color Bars Bit 7-0 Name FKEY Function Red/blue/CR data key value Reserved Table 3. Control Register Map (continued) Reg 19 1A 1B 1C 1D 1E 1F 1F 20 21 22 23 24 25 26 27 28-3F Test I/O Register 40 7-0 7-0 7-0 TESTDAT MASK Y Test data input/output Mask register Y-component input/ output Mask Register 50 60 Y-Component Register Bit 7-0 7-0 7-0 7-0 7-0 7-0 7-5 4-0 7-0 7-0 7-0 7-0 7-0 7-0 7-0 7-0 Name FP EL EH SL SH CBL FIELD LTYPE FREQL FREQ3 FREQ2 FREQM SYSPHL SYSPHM BURPHL BURPHM Function Front porch length Equalization pulse LOW length Equalization pulse HIGH length Vertical sync LOW length Vertical sync HIGH length Color bar length Field identification Line type identification Subcarrier frequency 4th byte (LSBs) Subcarrier frequency 3rd byte Subcarrier frequency 2nd byte Subcarrier frequency 1st byte (MSBs) Video phase offset LSBs Video phase offset MSBs Burst phase offset LSBs Burst phase offset MSBs Reserved Subcarrier Registers Standards Control Register Same as Reg 0E bit 7 but read-only 625/525 line per frame select Phase alternate line select 7.5 IRE Pedestal Enable Luminance gain settings Chrominance gain settings Horizontal sync tip length Breezeway length Burst length Color back porch length Extended color back porch 8 LSB Active video 8 LSB Active video start 8 LSB Active video end 8 LSB Extended color back porch 2 MSB Active video 2 MSB Active video start 2 MSB Active video end 2 MSB Timing Registers 10 11 12 13 14 15 16 17 18 18 18 18 7-0 7-0 7-0 7-0 7-0 7-0 7-0 7-0 7-6 5-4 3-2 1-0 SY BR BU CBP XBP VA VC VB XBP VA VC VB Notes: 1. Functions are listed in the order used for reading and writing. 2. For each register listed above, all bits not listed are reserved and should be set to zero to ensure proper operation. 3. The meaning of Register 04 (Key Control Register/Layering Control Register) is determined by Format Control Register bit 6 (TMC22191). 12 PRODUCT SPECIFICATION TMC22091/TMC22191 Control Register Definitions Global Control Register (00) 7 6 Reserved Reg 00 00 Bit 7-5 4 SRESET Name Function Reserved. Software reset. When LOW, resets and holds internal state machines and disables outputs. When HIGH (normal), starts and runs state machines and enables outputs. Video standard select. When LOW, the NTSC standard is generated with 7.5 IRE pedestal. When HIGH, PAL standard video is generated. This bit is ignored if Register 0E bit 7 is HIGH, enabling the 0E and 0F registers. Luminance input disable. When LOW (normal), luminance (Y) data from external frame buffer is enabled. When HIGH, luminance (Y) data into the TMC22x91 is forced to 0 IRE but sync pulses continue from the LUMA output. Chrominance input disable. When LOW (normal), burst and frame buffer data into the TMC22x91 are enabled. when HIGH, burst and frame buffer data are suppressed, enabling monochrome operation. Software reset enable. SRESET is forced LOW when the RESET pin is taken LOW. State machines are reset and held. When HRESET is LOW, RESET may be taken HIGH at any time. The TMC22x91 is enabled and a new frame is begun with line 1, field 1 on the next PXCK after SRESET is set HIGH. The D/A converters are powered down while RESET is LOW. When HRESET is HIGH, a new frame is begun with line 1, field 1 on the next PXCK after RESET is taken HIGH. SRESET is ignored. The D/A converters remain active during the reset sequence. 5 4 SRESET 3 PAL 2 LUMDIS 1 CHRDIS 0 HRESET 00 3 PAL 00 2 LUMDIS 00 1 CHRDIS 00 0 HRESET 13 TMC22091/TMC22191 PRODUCT SPECIFICATION Control Register Definitions (continued) Format Control Register (01) 7 Reserved Reg 01 01 Bit 7 6 LCREN 6 LCREN Name 5 RAMPEN Function Reserved. (TMC22191) Layering Control Register enable. When LOW, the Layering Control Register is not available and Key Control Register functions are enabled. In this mode, the TMC22191 functions like the TMC22091. When HIGH, the Layering Control Register takes the place of the Key Control Register and enables the layering functions. Data loaded into the Key or Layering Control Registers will remain but have a different meaning if this bit is changed. Modulated ramp test. When LOW (normal), the TMC22x91 encodes and outputs video corresponding to input data. When RAMPEN and CB are both HIGH, an internally generated 40 IRE modulated ramp is produced, preempting input data. Color bar test. When HIGH (normal), the TMC22x91 encodes and outputs video corresponding to input data. When CB, RAMPEN, and Format Control Register bit 0 are LOW, internally generated color bars are produced, preempting input data. PD23-0 input format select. Two bits select RGB, GBR, or YCBCR input data. When bits 3 and 2 are: 0 0 the CLUT output is interpreted as RGB and is converted to YCBCR. 0 1 is reserved. Bits 3 and 2 must be 00 or 10 when the Layering Control Register is enabled (TMC22191). 1 0 the CLUT output is interpreted as GBR, and is converted to YCBCR. 1 1 the CLUT output is interpreted as YCBCR. 01 1-0 INMODE PD23-0 input mode select. These two bits set up the TMC22x91 for either 444, 422, 15-bit, or 8-bit input modes. 00 01 10 11 24-bit/pixel GBR, RGB, or YCBCR444 data enters from PD23-0 YCBCR422 data enters from PD23-8; CR and CB alternate from PD15-8 15-bit/pixel GBR or RGB data from PD14-0 8-bit/pixel color indexed data enters from PD7-0. 4 CB 3 FORMAT 2 1 INMODE 0 01 5 RAMPEN 01 4 CB 01 3-2 FORMAT Bits 1 and 0 must be 00, 01, or 11 when the Layering Control Register is enabled (TMC22191). 14 PRODUCT SPECIFICATION TMC22091/TMC22191 Control Register Definitions (continued) Interface Control Register (02) 7 VITSEN Reg 02 Bit 7 6 SHCY Name VITSEN 5 TBASE Function VITS lines enable. When LOW, all UBB lines in the vertical interval are black burst regardless of input data. When HIGH, all UBB lines in the vertical interval become UVV active video and are dependent upon input data. Short-cycle test mode. When LOW, normal operation is enabled. when HIGH, EH (equalization pulse HIGH length) and SL (vertical sync LOW length) are shortened by 256. Time-base source select. These two bits set up the TMC22x91 for either genlock or frame buffer control of timing. When bits 5 and 4 are: 0 0 the encoder counts out its own time-base from input clock PXCK. 0 1 the encoder locks to synchronizing signals from external genlock. 1 0 the encoder locks to synchronizing signals from frame buffer controller. 02 3 SOUT Sync output mode select. When LOW, VHSYNC and VVSYNC output separate horizontal and vertical sync pulses. When HIGH, composite sync (H and V) is output on VVSYNC while horizontal sync is output on VHSYNC. Frame buffer signals enable. When LOW, VVSYNC and VHSYNC outputs to frame buffer are enabled. When HIGH, VVSYNC and VHSYNC outputs to frame buffer are disabled. PDC master/slave select. When LOW, PDC is an output where the encoder is requesting data from the frame buffer. When HIGH, PDC is an input, and directs the encoder to accept data from the frame buffer. Field lock select. When LOW, (in Slave mode) the encoder locks to each new field. When HIGH, the encoder locks to field 1 only. 4 3 SOUT 2 FBDIS 1 PDCDIR 0 FLDLK 02 6 SHCY 02 5-4 TBASE 02 2 FBDIS 02 1 PDCDIR 02 0 FLDLK 15 TMC22091/TMC22191 PRODUCT SPECIFICATION Control Register Definitions (continued) Test Control Register (03) 7 Reserved Reg 03 03 03 Bit 7 6 5 LIMEN TESTEN 6 LIMEN Name 5 TESTEN Function Reserved. Luminance limiter enable. When LOW, all luminance values are passed to modulator. when HIGH, luminance values are limited to 101 IRE. Test enable. When LOW, normal operation is enabled. When HIGH, TESTDAT7-0 (Register 40) is connected to the composite output (READ) and D/A converters (WRITE) for test. MSBs/LSBs hold select. When LOW, alternates MSBs and LSBs in test, at PXCK rate. When HIGH, reads/writes only MSBS or LSBS in test (per TSTMSB, bit 3) LSBS,MSBS hold select. When LOW, connects 2 LSBs to TESTDAT1-0 for testing when TESTEN is HIGH. When HIGH, connects 8 MSBs to TESTDAT7-0 for testing when TESTEN is HIGH. LUMA channel test. When LOW (normal), the luminance D/A converter is driven from luminance channel. When HIGH, the luminance D/A converter is driven from TESTDAT for testing when TESTEN is HIGH. 8-field subcarrier reset enable. When LOW, the internal subcarrier generator is reset with frequency and phase data from FREQ, SYSPH, and BURPH registers every eight fields. When HIGH, the internal subcarrier generator freeruns on the basis of frequency and phase data from the last time it was reset. When RESET goes LOW, the subcarrier frequency and phase will be reset from FREQ, SYSPH, and BURPH after field 8. CHROMA channel test. When LOW (normal), the chrominance D/A converter is driven from chrominance channel. When HIGH, the chrominance D/A converter is driven from TESTDAT when TESTEN is HIGH. 4 HOLDEN 3 TSTMSB 2 LUMTST 1 8FSUBR 0 CHRTST 03 4 HOLDEN 03 3 TSTMSB 03 2 LUMTST 03 1 8FSUBR 03 0 CHRTST 16 PRODUCT SPECIFICATION TMC22091/TMC22191 Control Register Definitions (continued) Key Control Register (04) 7 Reserved Reg 04 04 04 04 04 Bit 7 6 5 4 3 HKEN BUKEN SKEXT DKDIS 6 HKEN Name 5 BUKEN Function Reserved. Hardware key enable. When LOW, the KEY input pin ignored. When HIGH, the KEY input pin is enabled. Burst key enable. When LOW, output video burst is generated on TMC22x91. When HIGH, output burst is taken from genlock input data. Data key operation select. When LOW, data keying is allowed only during active video. When HIGH, keying is allowed during active video and blanking. Green/red/Y data key disable. When LOW, green/red/Y input data is enabled for data keying. When HIGH, green/red/Y input data is ignored for data keying. This function is enabled when Layering Control Register is enabled (TMC22191). Blue/green/CB data key disable. When LOW, Blue/green/CB input data is enabled for data keying. When HIGH, Blue/green/CB input data is ignored for data keying. This function is enabled when Layering Control Register is enabled (TMC22191). Red/blue/CR data key disable. When LOW, red/blue/CR input data is enabled for data keying. When HIGH, red/blue/CR input data is ignored for data keying. This function is enabled when Layering Control Register is enabled (TMC22191). Data key enable. When LOW, data keying is disabled. When HIGH, data keying is enabled. 4 SKEXT 3 DKDIS 2 EKDIS 1 FKDIS 0 SKEN 04 2 EKDIS 04 1 FKDIS 04 0 SKEN 17 TMC22091/TMC22191 PRODUCT SPECIFICATION Control Register Definitions (continued) Layering Control Register (04) (TMC22191) 7 LAYMODE Reg 04 04 04 04 Bit 7 6 5 4 6 HKEN Name LAYMODE HKEN BUKEN SKEXT 5 BUKEN Function MSB of Layer Assignments select. Hardware key enable. When LOW, the KEY input pin ignored. When HIGH, the KEY input pin is enabled. Burst key enable. When LOW, output video burst is generated on TMC22191. When HIGH, output burst is taken from genlock input data. Data key operation select. When LOW, data keying is allowed only during active video. When HIGH, data keying is allowed during active video and blanking. Three LSBs of Layer Assignments select. Data key enable. When LOW, data keying is disabled. When HIGH, data keying is enabled. 4 SKEXT 3 2 LAYMODE 1 0 SKEN 04 04 3-1 0 LAYMODE SKEN Key Value Registers (05-07) Reg 05 06 07 Bit 7-0 7-0 7-0 Name DKEY EKEY FKEY Function Green/red/Y data key value. Eight bits hold the match value which triggers keying on red/Y. Blue/green/U data key value. Eight bits hold the match value which triggers keying on green/U. Red/blue/V key value. Eight bits hold the match value which triggers keying on blue/V. 18 PRODUCT SPECIFICATION TMC22091/TMC22191 Control Register Definitions (continued) Miscellaneous Control Register (0E) 7 EFEN Reg 0E Bit 7 6 COMPD/A Name EFEN 5 SVIDD/A Function Register 0E and 0F enable. When LOW, the functions of Register 0E and 0F are disabled. When HIGH, Registers 0E and 0F are active. When Registers 0E and 0F are enabled, Register 00 bit 3 is ignored. Register 0E bit 7 will read back whatever value was written. COMPOSITE D/A disable. When HIGH, the COMPOSITE D/A converter is powered-down. When LOW, the D/A is enabled. LUMA/CHROMA D/A disable. When HIGH, the LUMA and CHROMA D/A converters are powered-down. When LOW, they are enabled. Luminance processing enable. When FKREN is HIGH, the KEY input defines the function of CVBS input data. When the KEY input is HIGH, CVBS data is keyed over PD input data. When KEY is LOW, CVBS data is assumed to be luminance data delayed by one When FKREN is LOW, the KEY input operates normally, switching between CVBS and PD data. Luminance ratio control bit. When LOW, 1/2 of current luminance and 1/2 of field delayed luminance from the CVBS input are added to yield a new combined luminance value. When RATIO is HIGH, 3/4 of current luminance is added to 1/4 of the delayed luminance to produce a new luminance value. Luminance-pass threshold. The difference between current luminance and delayed luminance (from the CVBS inputs) is compared against a preset threshold set by TFLK. When TFLK is LOW, the high threshold must be exceeded to trigger the combining of current and delayed luminance (according to RATIO). If the higher threshold is not exceeded, current luminance is passed without modification. When TFLK is HIGH, a lower threshold is used to trigger the combining of current and delayed luminance. EH/SL offset control bit. When LOW, the true value of EH and SL is offset by 256. When HIGH, the true value for EH and SL is offset by 512. NTSC/PAL color bars select. When HIGH, color bars with 100% white level are selected. When LOW, color bars will have 75% white level. 4 FKREN 3 RATIO 2 TFLK 1 T512 0 CB100 0E 0E 0E 6 5 4 COMPD/A SVIDD/A FKREN 0E 3 RATIO 0E 2 TFLK 0E 0E 1 0 T512 CB100 19 TMC22091/TMC22191 PRODUCT SPECIFICATION Control Register Definitions (continued) Standards Control Register (0F) 7 EFEN Reg 0F 0F 0F 0F 0F Bit 7 6 5 4 3-2 6 SIX25 Name EFEN SIX25 PALID SETUP YGAIN 5 PALID Function Same as Register 0E bit 7, but read-only. Select 625 lines per frame. When HIGH, the encoder assumes 625 line per frame. When LOW, 525 lines per frame are assumed. PAL select. When HIGH, Phase alternate line (PAL) operation is selected. When LOW, operation conforms to NTSC standards. Setup enable. When HIGH, a 7.5 IRE Pedestal is added to the output video. when LOW, no pedestal is added. Luminance gain settings are adjusted to conform to the following NTSC and PAL standards: 00 01 10 11 0F 1-0 CGAIN NTSC without SETUP NTSC-A and PAL-M PAL-I and PAL-N Reserved 4 SETUP 3 YGAIN 2 1 CGAIN 0 Chrominance gain settings are adjusted to conform to the following NTSC and PAL standards: 00 01 10 11 NTSC without SETUP NTSC-A and PAL-M PAL-I and PAL-N Reserved Timing Registers (10-17) Reg 10 11 12 13 14 Bit 7-0 7-0 7-0 7-0 7-0 Name SY BR BU CBP XBP Function Horizontal sync tip length. This 8-bit register holds a value extending from 0 to 255 PCK cycles. Breezeway length. This 8-bit register holds a value extending from 0 to 255 PCK cycles. Burst length. This 8-bit register holds a value extending from 0 to 255 PCK cycles. Color back porch length. This 8-bit register holds a value extending from 0 to 255 PCK cycles. Extended color back porch 8 LSBs. This 8-bit register holds the LSBs of a 10-bit value extending from 0 to 1023 PCK cycles. The two MSBs are located in control register 18. Active video 8 LSBs. This 8-bit register holds the LSBs of a 10-bit value extending from 0 to 1023 PCK cycles. The two MSBs are located in control register 18. Active video start 8 LSBs. This 8-bit register holds the LSBs of a 10-bit value which is the initial half active video length extending from 0 to 1023 PCK cycles. The two MSBs are located in control register 18. Active video end 8 LSBs This 8-bit register holds the LSBs of a 10-bit value which is the end half active video length extending from 0 to 1023 PCK cycles. The two MSBs are located in control register 18. 15 7-0 VA 16 7-0 VC 17 7-0 VB 20 PRODUCT SPECIFICATION TMC22091/TMC22191 Control Register Definitions (continued) Timing Register (18) 7 XBP Reg 18 Bit 7-6 Name XBP 6 5 VA Function Extended color back porch 2 MSBs. These two bits hold the MSBs of a 10-bit value extending from 0 to 1023 PCK cycles. The LSBs are located in control register 14. Active video 2 MSB. These two bits hold the MSBs of a 10-bit value extending from 0 to 1023 PCK cycles. The LSBs are located in control register 15. Active video start 2 MSBs. These two bits hold the MSBs of a 10-bit value which is the initial half active video length extending from 0 to 1023 PCK cycles. The LSBs are located in control register 16. Active video end 2 MSBs. These two bits hold the MSBs of a 10-bit value which is the end half active video length extending from 0 to 1023 PCK cycles. The LSBs are located in control register 17. 4 3 VC 2 1 VB 0 18 18 5-4 3-2 VA VC 18 1-0 VB Timing Registers (19-1E) Reg 19 1A 1B Bit 7-0 7-0 7-0 Name FP EL EH Function Front porch length. This 8-bit register holds a value extending from 0 to 255 PCK cycles. Equalization pulse LOW length. This 8-bit register holds a value from 0 to 255 PCK cycles. Equalization pulse HIGH length. This 8-bit register holds a value extending from 0 to 255 PCK cycles. This value, when added to 256 (or 512), determines the final pulse length in the range of 256 to 511 (or 767) PCK cycles. Vertical sync LOW length. This 8-bit register holds a value from 0 to 255 PCK cycles. This value, when added to 256 (or 512), determines the final pulse length in the range of 256 to 511 (or 767) PCK cycles. Vertical sync HIGH length. This 8-bit register holds a value extending from 0 to 255 PCK cycles. Color bar length. This 8-bit register holds a value which is the length of each color bar displayed extending from 0 to 255 PCK cycles. 1C 7-0 SL 1D 1E 7-0 7-0 SH CBL Timing Register (1F) 7 6 FIELD Reg 1F Bit 7-5 Name FIELD Function Field identification (read only). These three bits are updated 12 PXCK periods after each VHSYNC. They allow the user to determine field type on a continuous basis. Line type identification (read only). These five bits are updates 5 PXCK periods after each VHSYNC. They allow the user to determine line type on a continuous basis. 5 4 3 2 LTYPE 1 0 1F 4-0 LTYPE 21 TMC22091/TMC22191 PRODUCT SPECIFICATION Control Register Definitions (continued) Subcarrier Registers (20-27) Reg 20 Bit 7-0 Name FREQL Function Subcarrier frequency 4th byte (LSBs). This 8-bit register holds the LSB (bits 7-0) of the 32-bit subcarrier frequency value (non-genlock modes). The next eight most significant bits are held in Register 21. Subcarrier frequency 3rd byte. This 8-bit register holds bits 15:8 of the subcarrier frequency value (non-genlock modes). The next eight most significant bits are held in Register 22. Subcarrier frequency 2nd byte. This 8-bit register holds bits 23-16 of the subcarrier frequency value (non-genlock modes). The eight MSBs are held in Register 23. Subcarrier frequency 1st byte (MSBs). This 8-bit register holds the MSBs (bits 31-24) of the 32-bit subcarrier frequency value (non-genlock modes). Video phase offset LSBs. This 8-bit register holds the 8 LSBs of color subcarrier phase offset during active video. Video phase offset MSBs. This 8-bit register holds the 8 MSBs of color subcarrier phase offset during active video. Burst phase offset LSBs. This 8-bit register holds the 8 LSBs of burst phase offset for color adjustment. Burst phase offset MSBs. This 8-bit register holds the 8 MSBs of burst phase for color adjustment. 21 7-0 FREQ3 22 7-0 FREQ2 23 24 25 26 27 7-0 7-0 7-0 7-0 7-0 FREQM SYSPHL SYSPHM BURPHL BURPHM Test I/O Register (40) Reg 40 Bit 7-0 Name TESTDAT Function Test data input/output. This 8-bit register holds MSBs or LSBs, as determined by the Test Control Register. This control address does not auto-increment during read or write operations. To exit the test mode, reset the Control Register pointer by setting A1-0 and R/W LOW and then bring CS LOW. Mask Register (50) Reg 50 Bit 7-0 Name MASK Function Mask register. This 8-bit register holds an 8-bit word that is logically ANDed with the incoming data presented to the three CLUTs in color-index mode. This register is a write-only register. Y-Component Register (60) Reg 60 Bit 7-0 Name Y Function Y-component register. This register holds the contents of the luminance value before the Sync and Blank Insert circuitry of the encoder. Loading the Control Register pointer with 60h brings 8-bit Y values out on the D7-0 port. 22 PRODUCT SPECIFICATION TMC22091/TMC22191 Color Lookup Table The CLUT can be used in a variety of ways, depending on the data format and source presented to the PD port. The CLUT is loaded like a RAMDAC, sequentially writing one byte to each of the three locations associated with the selected CLUT address. These three locations are referred to as Tables D, E, and F as shown in table 16 (not R,G, and B because they may or may not contain RGB information). and are loaded in that sequence. The address will increment automatically after the three values at one address are written or read. gamma correction, are easily loaded. The color data is loaded into the tables in G-B-R sequence in GBR mode, and R-G-B sequence in RGB mode. Luminance/Color Difference Modes The TMC22x91 expects Y, B-Y, and R-Y signals at the input to its modulator section. When presenting CCIR-601 YCBCR or digitized Y, B-Y, R-Y data to the CLUT, gain and offset factors are needed. Table 4 specifies the recommended transfer functions. The CLUT is loaded in Y-CB-CR sequence. Color-index Modes In color-index (CI) mode, the CLUT is used to store the color look-up data, translating the 8-bit source pixel data into 24-bit RGB colors. Table D holds red data, Table E is green data, and Table F holds blue Data. The incoming data are presented to the three tables in parallel, and a 24-bit output is produced. When the encoder is connected in parallel with a RAMDAC in a VGA system, the CLUT can be loaded simultaneously with the CLUT in the output RAMDAC. If a 6-bit RAMDAC is employed, 6 bits can be loaded via data pins D7-2 (MSB justified). The two LSBs should be set to 00 for optimal black level representation, but the largest error introduced by extraneous data in the LSBs is 3/4 LSB (at 6 bits). The encoder will produce the closest possible translation of the VGA colors in the encoded video environment. Overlay Operation For the TMC22091 and TMC22191 (when Format Control Register Bit 6 = LOW), the OL4-0 inputs are inactive. In CCIR-601 operation, the nominal data range for Y is from 16 to 235 and for CB and CR is from 16 to 240. This means that CLUT locations 0 to 15 and 241 to 255 are available for overlay colors. When the overlay locations are addressed (by forcing CLUT addresses outside the normal CCIR-601 data range), the addressed CLUT data is encoded resulting in the specific color found in that CLUT location. Overlay colors information stored in the unused CLUT locations must be Y, B-Y, R-Y values. Y, B-Y, and R-Y values are found from RGB values by: Y = 0.299 R + 0.587 G + 0.114 B B-Y = -0.299 R – 0.587 G + 0.886 B R-Y = 0.701 R – 0.587 G – 0.114 B For the TMC22191, when the Format Control Register Bit 6 = HIGH, Overlay is controlled by the OL4-0 inputs which directly access CLUT locations, 01 thru 0F and F1 thru FF, as shown in Table 5. The values stored in these CLUT locations must be in RGB format. GBR/RGB Modes The nominal configuration for GBR/RGB modes is unity gain (CLUT data = CLUT address) for PAL and NTSC. Other transfer functions, such as gain adjustment, offset, and Table 4. CLUT Transfer Functions for NTSC and PAL Input Format (CLUT Address) Component R G B Y CB CR Y B-Y R-Y Data Range 0 to 255 0 to 255 0 to 255 16 to 235 ±112 ±112 0 to 255 ±127 ±127 Transfer Equations R0=R G0=G B0=B YO = Y * 1.1644 – 18.63 (B-Y)O = CB * 1.0126 (R-Y)O = CR * 0.8011 Y0=Y (B-Y)O = (B-Y) * 0.893 (R-Y)O = (R-Y) * 0.7065 Output Format (CLUT Data) Component RO GO BO YO (B-Y)O (R-Y)O YO (B-Y)O (R-Y)O Data Range 0 to 255 0 to 255 0 to 255 0 to 255 ±113 ±90 0 to 255 ±113 ±90 23 TMC22091/TMC22191 PRODUCT SPECIFICATION Table 5. CLUT Locations Addressed by Overlay Inputs (TMC22191) OL4-0 00 01 02 • • 0E 0F 10 11 12 • • CLUT location No Overlay 01 02 • • 0E 0F No Overlay F1 F2 • • Table 5. CLUT Locations Addressed by Overlay Inputs (TMC22191) (continued) OL4-0 1E 1F CLUT location FE FF Color-space Conversion in the Matrix When the input pixels are in RGB, GBR, or color-index format and the CLUT is bypassed (TMC22191), the Matrix remains enabled, converting RGB data to color-difference format. When the input pixels are in 444 format (YCBCR444, RGB, GBR, CI), the Interpolator (which converts 422 to 444) is not active. When the input pixels are in YCBCR format, the CLUT is enabled to scale the data to color-difference values and the Matrix is inactive. In colorindex mode, the Matrix is active, converting the RGB CLUT output data to color-difference values. Table 6. Pixel Input Operation for Format Control Register bit 6 = HIGH (TMC22191) Format Control Register FORMAT Bit 3,2 00 (RGB) 00 00 00 01 10 (GBR) 10 10 10 11 INMODE Bit 1,0 00 (444) 01 (422) 10 (15-bit) 11 (CI) xx 00 (444) 01 (422) 10 (15-bit) 11 (CI) xx Pixel Data Format BYPASS = LOW CLUT bypassed RGB RGB RGB RGB reserved GBR GBR GBR GBR not allowed BYPASS = HIGH CLUT enabled YCBCR444 YCBCR422 RGB15 CI reserved YCBCR444 YCBCR422 GBR15 CI not allowed Format Control Register Bit 6 = HIGH MSB 23 Pixel 1 Pixel 2 Pixel 3 Pixel 4 16 15 87 LSB 0 Format Control Register Bit 6 = LOW MSB 23 Pixel 1 Pixel 2 Pixel 3 Pixel 4 16 15 87 LSB 0 Y1 Y2 Y3 Y4 Yn Yn+1 CB1 CB1 CB3 CB3 CBn CBn CR1 CR1 CR3 CR3 CRn CRn Y1 Y2 Y3 Y4 Yn Yn+1 CB1 CR1 CB3 CR3 CBn CRn 27003A Pixel n Pixel n+1 Pixel n Pixel n+1 Note: The pixel input sequence begins on the first LDV pulse after PDC goes HIGH. n = Odd number Figure 2. Pixel Data (PD23-0) Sequence for YCBCR422 24 PRODUCT SPECIFICATION TMC22091/TMC22191 Gamma Correction Gamma is built into broadcast television systems as a correction factor for nonlinearity in image acquisition (nonlinear conversion of light into current in a vidicon) and at the display (phosphor nonlinearity in converting current into light). A Gamma corrector transfer function takes the form of Output = k ( Input )1/γ where a typical Gamma is 2.2 for NTSC, 2.8 for PAL. Computer systems usually ignore Gamma in driving a display monitor. Each R, G, and B channel is treated as linear. When encoding a computer display output to video, the user must decide whether to apply a gamma correction factor and, if so, what value. It is a good assumption that, since the digital video input over the CVBS bus is in composite form, it has been Gamma corrected. Gamma correction is applied in the RGB domain. When operating in YCBCR, for example when encoding a CCIR601 signal, Gamma should have already been applied. Gamma correction is readily added to the RGB transfer equations shown in Table 4. Table 7. Horizontal Timing Specifications Parameter FP SY BR BU CBP VA H NTSC-M (µs) 1.5 4.7 0.6 2.5 1.6 52.6556 63.5556 PAL-I (µs) 1.65 4.7 0.9 2.25 2.55 51.95 64.0 PAL-M (µs) 1.9 4.95 0.9 2.25 1.8 51.692 63.492 Vertical Programming Vertical interval timing is also fully programmable, and is established by loading the timing registers with the durations of each vertical timing element, the duration expressed in PCK clock cycles. In this way as with horizontal programming, any pixel rate between 10 and 15 Mpps can be accommodated, and any desired standard or non-standard vertical video timing may be produced. Like horizontal timing parameters, vertical timing parameters are calculated as follows: t = N x (PCK period) = N x (2 x PXCK period) where N is the value loaded into the appropriate timing register, and PCK is the pixel clock period. The Vertical Interval comprises several different line types based upon H, the Horizontal line time. H = (2 x SL) + (2 x SH) [Vertical sync pulses] = (2 x EL) + (2 x EH) [Equalization pulses] The VB and VC lines are added to produce the half-lines needed in the vertical interval at the beginning and end of some fields. These must properly mate with components of the normal lines. VB = CBP + VA - XBP = H/2 – CBPVC = VA – (EL + EH) = VA – H/2 where Equalization HIGH and LOW pulses (EL + EH) = H/2 and the Extended Color Back Porch, XBP = VA + CBP –VB. XBP begins after the end of burst, BU, taking the place of CBP in vertical interval UBV lines. Figure 5 shows the vertical sync and equalization pulse detail Video Timing The TMC22x91 can be programmed to accommodate a wide range of system timing requirements. With a line locked pixel rate of 10 to 15 Mpps, the digitally synthesized horizontal waveforms and subcarrier frequency and phase are determined from 24 registers that are loaded by a controller. Horizontal Programming Horizontal interval timing is fully programmable, and is established by loading the timing registers with the durations of each horizontal element. The duration is expressed in PCK clock cycles. In this way, any pixel clock rate between 10 MHz and 15 MHz can be accommodated, and any desired standard or non-standard horizontal video timing may be produced. Figure 3 illustrates the horizontal blanking interval with timing register identification. Horizontal timing parameters can be calculated as follows: t = N x (PCK period) = N x (2 x PXCK period) where N is the value loaded into the appropriate timing register, and PCK is the pixel clock period. Horizontal timing resolution is two PXCK periods. PXCK must be chosen such that it is an even integer multiple of the horizontal line frequency. This ensures that the horizontal line period, H, contains an integer number of pixels. The horizontal line comprises the sum of appropriate elements. H = FP + SY + BR + BU + CBP + VA When programming horizontal timing, subtract 5 PCK periods from the calculated values of CBP and add 5 PCK periods to the calculated value for VA. Table 8. Vertical Timing Specifications Parameter (µs) H EH EL SH SL NTSC-M (µs) 63.5556 29.4778 2.3 4.7 27.1 PAL-I (µs) 64 29.65 2.35 4.7 27.3 PAL-M (µs) 63.492 29.45 2.3 4.65 27.1 25 TMC22091/TMC22191 PRODUCT SPECIFICATION H H/2 Burst EH VA FP SY FP BU FP VA 24318B EL SL SH 24319A Figure 3. Horizontal Blanking Interval Timing Figure 4. Sync and Equalization Pulse Detail Timing FIELDS 1 AND 3 524 523 PRE-EQUALIZATION 3H 1 2 3 VERTICAL BLANKING VERTICAL SYNC 3H 4 5 6 POST-EQUALIZATION 3H 7 8 9 21 10 19 20 22 UVV UVV EE EE EE SS SS SS EE EE EE UBB UBB UBB UVV UVV VHSYNC VVSYNC COMPOSITE SYNC 262 263 264 FIELDS 2 AND 4 265 266 267 268 269 270 271 272 273 282 283 284 285 UVV VHSYNC UVE EE EE ES SS SS SE EE EE EB UBB UBB UBV UVV UVV VVSYNC COMPOSITE SYNC 27000A Figure 5. NTSC Vertical Interval 26 PRODUCT SPECIFICATION TMC22091/TMC22191 Table 9. NTSC Field/Line Sequence and Identification Field 1 FIELD ID = x00 Line 1 2 3 4 5 6 7 8 9 10 ••• 20 21 22 ••• 262 263 EE SS EB UVV UBV Field 2 FIELD ID = x01 Line 264 265 266 267 268 269 270 271 272 273 ••• 282 283 284 ••• 524 525 ID EE EE ES SS SS SE EE EE EB UBB ••• UBB UBV UVV ••• UVV UVV LTYPE 00 00 01 03 03 02 00 00 10 0D ••• 0D 0E 0F ••• 0F. 0F SE ES UBB UVE Field 3 FIELD ID = x10 Line 1 2 3 4 5 6 7 8 9 10 ••• 20 21 22 ••• 262 263 ID EE EE EE SS SS SS EE EE EE UBB ••• UBB UVV UVV ••• UVV UVE LTYPE 00 00 00 03 03 03 00 00 00 0D ••• 0D 0F 0F ••• 0F 0C Field 4 FIELD ID = x11 Line 264 265 266 267 268 269 270 271 272 273 ••• 282 283 284 ••• 524 525 ID EE EE ES SS SS SE EE EE EB UBB ••• UBB UBV UVV ••• UVV UVV LTYPE 00 00 01 03 03 02 00 00 10 0D ••• 0D 0E 0F ••• 0F 0F ID EE EE EE SS SS SS EE EE EE UBB ••• UBB UVV UVV ••• UVV UVE LTYPE 00 00 00 03 03 03 00 00 00 0D ••• 0D 0F 0F ••• 0F 0C Equalization pulse Vertical sync pulse Equalization broad pulse Active video Half-line black, half-line video Half-line vertical sync pulse, half-line equalization pulse Half-line equalization pulse, half-line vertical sync pulse Black burst Half-line video, half-line equalization pulse Master and Genlock mode details of VHSYNC, VVSYNC, and composite VVSYNC (SOUT = HIGH) outputs are shown in Figures 5 and 6. When VHSYNC and VVSYNC are used as inputs (Slave mode), their falling edges mark the beginning of the sync interval and the width of the input pulse is specified under Operating Conditions. 27 TMC22091/TMC22191 PRODUCT SPECIFICATION 1247 1248 FIELDS 1 AND 5 24 2 3 4 5 6 7 22 23 25 26 1249 1250 1 UVV VHSYNC VVSYNC COMPOSITE SYNC 309 VE EE EE SS SS SE EE EE BB UBB UBB UBB UBV UVV UVV 310 311 FIELDS 2 AND 6 312 313 314 315 316 317 318 319 320 334 335 336 337 UVV VHSYNC VVSYNC COMPOSITE SYNC 622 VV EE EE ES SS SS EE EE EB UBB UBB UBB UBV UVV UVV 623 FIELDS 3 AND 7 649 627 628 629 630 631 632 647 648 650 651 624 625 626 UVV VHSYNC VVSYNC COMPOSITE SYNC 934 VE EE EE SS SS SE EE EE UBB UBB UBB UBB UBV UVV UVV 935 936 FIELDS 4 AND 8 937 938 939 940 941 942 943 944 945 959 960 961 962 UVV VHSYNC VVSYNC COMPOSITE SYNC UV EE EE ES SS SS EE EE EB BB UBB UBB UBV UVV UVV 27001A Figure 6. PAL Vertical Interval 28 PRODUCT SPECIFICATION TMC22091/TMC22191 Table 10. PAL Field/Line Sequence and Identification Field 1 FIELD ID = 000, 100 Line 1 2 3 4 5 6 7 8 ••• 22 23 24 ••• 308 309 310 311 312 EE SS EB -BB -VV -VE Field 2 FIELD ID = 001, 101 Line 313 314 315 316 317 318 319 320 ••• 335 336 337 ••• 621 622 623 624 625 ID ES SS SS EE EE EB UBB UBB ••• UBB UVV UVV ••• UVV -VV -VE EE EE LTYPE 01 03 03 00 00 10 0D 0D ••• 0D 0F 0F ••• 0F 07 04 00 00 SE ES UBB UVV UVE UBV Field 3 FIELD ID = 010, 110 Line 626 627 628 629 630 631 632 633 ••• 647 648 649 ••• 933 934 935 936 937 ID SS SS SE EE EE UBB UBB UBB ••• UBB UBV UVV ••• UVV UVV UVV EE EE LTYPE 03 03 02 00 00 0D 0D 0D ••• 0D 0E 0F ••• 0F 0F 0F 00 00 Field 4 FIELD ID = 011, 111 Line 938 939 940 941 942 943 944 945 ••• 960 961 962 ••• 1246 1247 1248 1249 1250 ID ES SS SS EE EE EB -BB UBB ••• UBB UVV UVV ••• UVV UVV -VE EE EE LTYPE 01 03 03 00 00 10 05 0D ••• 0D 0F. 0F ••• 0F 0F 04 00 00 ID SS SS SE EE EE -BB UBB UBB ••• UBB UBV UVV ••• UVV UVV -VV EE EE LTYPE 03 03 02 00 00 05 0D 0D ••• 0D 0E 0F ••• 0F 0F 07 00 00 Equalization pulse Vertical sync pulse Equalization broad pulse Black burst with color burst suppressed Active video with color burst suppressed Half-line video, half-line equalization pulse, color burst suppressed. Half-line vertical sync pulse, half-line equalization pulse Half-line equalization pulse, half-line vertical sync pulse Black burst Active video Half-line video, half-line equalization pulse half-line black, half-line video 29 TMC22091/TMC22191 PRODUCT SPECIFICATION 521 522 FIELDS 1 AND 5 523 524 525 1 2 3 4 5 6 7 8 9 17 18 UVV VHSYNC UVV EE EE EE SS SE SS EE EE EE BB BB UBB UBB UVV VVSYNC COMPOSITE SYNC 259 260 FIELDS 2 AND 6 261 262 263 264 265 266 267 268 269 270 271 279 280 281 UVV VHSYNC VE EE EE ES SS SS SE EE EE EB BB UBB UBV UVV UVV VVSYNC COMPOSITE SYNC 521 522 523 524 525 1 18 FIELDS 3 AND 7 2 3 4 5 6 7 8 9 17 UVV VHSYNC VV EE EE EE SS SS SS EE EE EE BB UBB UBB UBB UVV VVSYNC COMPOSITE SYNC 258 259 260 261 262 263 280 FIELDS 4 AND 8 264 265 266 267 268 269 270 271 279 281 UVV VHSYNC UV VE EE EE ES SS SS SE EE EE EB BB UBB UBB UBV UVV VVSYNC COMPOSITE SYNC 27082A Figure 7. PAL-M Vertical Interval 30 PRODUCT SPECIFICATION TMC22091/TMC22191 Table 11. PAL-M Field/Line Sequence and Identification Field 1 FIELD ID = 000, 100 Line 1 2 3 4 5 6 7 8 9 ••• 17 18 ··· 259 260 261 262 ID SS SS SS EE EE EE -BB -BB UBB ••• UBB UVV ··· UVV -VE EE EE LTYPE 03 03 03 00 00 00 05 05 0D ••• 0D 0F ··· 0F 04 00 00 Field 2 FIELD ID = 001, 111 Line 263 264 265 266 267 268 269 270 271 ••• 279 280 281 ••• 521 522 523 524 525 EE SS EB -BB -VV -VE Field 3 FIELD ID = 010, 110 Line 1 2 3 4 5 6 7 8 ••• 17 18 ••• 258 259 260 261 262 ID SS SS SS EE EE EE -BB UBB ••• UBB UVV ••• UVV -VV -VE EE EE LTYPE 03 03 03 00 00 00 05 05 ••• 0D. 0F ••• 0F 07 04 00 00 Field 4 FIELD ID = 011, 111 Line 263 264 265 266 267 268 269 270 271 ••• 279 280 281 ••• 521 522 523 524 525 ID ES SS SS SE EE EE EB -BB UBB ••• UBB UBV UVV ••• UVV UVV EE EE EE LTYPE 01 03 03 02 00 00 10 05 1D ••• 0D 0E. 0F ••• 0F 0F 00 00 00 ID ES SS SS SE EE EE EB -BB UBB ••• UBB UBV UVV ••• UVV -VV EE EE EE LTYPE 01 03 03 02 00 00 10 05 1D ••• 0D 0E. 0F ••• 0F 07 00. 00 00 SE ES UBB UVV UVE UBV Equalization pulse Vertical sync pulse Equalization broad pulse Black burst with color burst suppressed Active video with color burst suppressed Half-line video, half-line equalization pulse, color burst suppressed. Half-line vertical sync pulse, half-line equalization pulse Half-line equalization pulse, half-line vertical sync pulse Black burst Active video Half-line video, half-line equalization pulse half-line black, half-line video 31 TMC22091/TMC22191 PRODUCT SPECIFICATION Table 12. Standard Timing Parameters Field Horizontal Pixel PXCK Rate Freq. Rate Freq. (Hz) (kHz) (Mpps) (MHz) 59.94 15.734266 59.94 15.734266 59.94 15.734266 50.00 15.625000 50.00 15.625000 50.00 15.625000 60.00 15.750000 60.00 15,750000 60.00 15,750000 12.27 13.50 14.32 14.75 13.50 15.00 12.50 13.50 14.30 24.54 27.00 28.64 29.50 27.00 30.00 25.01 27.00 28.60 Timing Register (hex) SY 10 3A 40 43 45 40 46 3E 44 47 BR 11 07 08 09 0D 0C 0D 0B 0C 0D BU 12 1F 22 24 21 1E 22 1C 1E 20 CBP XBP VA 13 14 15 0F 13 12 21 22 21 13 13 15 23 3F 54 6D 4D 73 26 26 4C 8B CA F7 03 BE 11 86 Bf E8 VC 16 05 1D 30 2B 0E 31 FE 12 22 VB Note 1 FP 17 18 19 77 9D B5 B7 93 BF 8B 99 AC 65 65 65 75 65 75 61 65 65 12 13 15 19 16 19 18 1A 1B EL EH2 SL2 SH 1A 1B 1C 1D 1C 1F 21 23 20 23 1D 1F 21 6A 8E A6 B5 90 BD 70 8E A5 4C 6E 84 93 71 9A 53 6E 84 3A 3F 43 45 3F 47 3A 3F 42 CBL 1E 52 59 5F 61 58 62 52 57 5D Standard NTSC sqr. pixel NTSC CCIR-601 NTSC 4x FSC PAL sqr. pixel PAL CCIR-601 PAL 15 Mpps PAL-M sqr.pixel PAL-M CCIR-601 PAL-M 4x FSC Notes: 1. XBP, VA, VC, and VB are 10-bit values. The 2 MSBs for these four variables are in Timing Register 18. See Table 3. 2. EH and SL are 9-bit values. A most significant "1" is forced by the TMC22x91 since EH and SL must range from 256 to 511. EH and SL may be extended to 767. Only the eight LSBs are stored in Timing Registers 1B and 1C. 3. Every calculated timing parameter has a minimum value of 5 except EH and SL which have minimum values of 256. VITS Insertion In both NTSC and PAL, the TMC22x91 can be set up to allow Vertical Interval Test Signals (VITS) in the vertical interval in place of normal black burst lines (UBB). This is controlled by Interface Control Register bit 7. If this bit is LOW, UBB lines are black burst and are independent of TMC22x91 input data. If the bit is HIGH, all vertical interval UBB lines become UVV. UVV lines are active video and depend upon data input to the TMC22x91. VITS lines may carry special test signals or pass captioning data through the encoder. Subcarrier Programming The color subcarrier is produced by an internal 32-bit digital frequency synthesizer which is completely programmable in frequency and phase. Separate registers are provided for phase adjustment of the color burst and of the active video, permitting external delay compensation and color adjustment. In Master or Slave mode, the subcarrier is internally synchronized to establish and maintain a specified relationship between the falling edge of horizontal sync and color burst phase (SCH). In NTSC and PAL, SCH synchronization is performed every eight fields, on field 1 of the eight-field sequence. Proper subcarrier phase is maintained through the entire eight fields, including the 25 Hz offset in PAL systems. See the description of 8FSUBR under Test Control Register bit 1 for the subcarrier reset function. In Genlock mode, the phase and relative frequency of the incoming video are transmitted by the TMC22071 Genlocking Video Digitizer over the CVBS bus at the beginning of each line, which synchronize the digital subcarrier synthesizer. When key control register bit BUKEN is HIGH and digitized burst from the TMC22071 is passed through to the reconstruction D/A converter, the reference subcarrier for the chrominance modulator is still synthesized within the encoder. Edge Control SMPTE 170M NTSC and Report 624 PAL video standards call for specific rise and fall times on critical portions of the video waveform. The TMC22x91 does this automatically. The TMC22x91 digitally defines slopes compatible with SMPTE 170M NTSC or CCIR Report 624 PAL on: 1. 2. 3. H and V Sync leading and trailing edges. Burst envelope. Active video leading and trailing edges. 32 PRODUCT SPECIFICATION TMC22091/TMC22191 NTSC Subcarrier For NTSC encoding, the subcarrier synthesizer frequency has a simple relationship to the pixel clock period, repeating over 2 lines: The decimal value is: ( 455 ⁄ 2 ) 32 FREQ = ----------------------------- × 2 ( pixels/line ) This value must be converted to binary and split into four 8-bit registers, FREQM, FREQ2, FREQ3, and FREQL. The number of pixels/line is: Pixels/line = (2/PXCK frequency) (H period) SYSPH establishes the appropriate phase relationship between the internal synthesizer and the chroma modulator. The nominal value for SYSPH is zero. Other values for SYSPH must be converted to binary and split into two 8-bit registers, SYSPHM and SYSPHL. Burst Phase (BURPH) sets up the correct relative NTSC modulation angle. The value for BURPH is: BURPH = SYSPH + 8,192 This value must be converted to binary and split into two 8-bit registers, BURPHM and BURPHL. The decimal number 8,192 advances the burst phase by 45°. PAL Subcarrier The PAL relationship is more complex, repeating only once in 8 fields (the well-known 25 Hz offset): ( 1135 ⁄ 4 ) + ( 1 ⁄ 625 ) 32 FREQ = -------------------------------------------------- × 2 ( pixels/line ) This value must be converted to binary and split as described previously for NTSC. For PAL, the decimal value for SYSPH is found from: FREQ SYSPH = --------------- = BURPH 17 2 This value must be converted to binary and split into two 8-bit registers, SYSPHM and SYSPHL. Burst Phase in PAL is identical to SYSPH. Therefore, the same values for SYSPHM and SYSPHL must be used for BURPHM and BURPHL. PAL-M Subcarrier ( 909 ⁄ 4 ) 32 FREQ = ----------------------------- × 2 ( pixels/line ) FREQ SYSPH = --------------- = BURPH 17 2 Table 13. Standard Subcarrier Parameters Field Rate (Hz) 59.94 59.94 59.94 50.00 50.00 50.00 60 60 60 Horizontal Freq. (kHz) 15.734266 15.734266 15.734266 15.625000 15.625000 15.625000 15.750 15,750 15,750 Pixel Rate (MHz) 12.27 13.50 14.32 14.75 13.50 15.00 12.50 13.50 14.30 PXCK Freq. (MHz) 24.54 27.00 28.64 29.50 27.00 30.00 25.01 27.00 28.60 Subcarrier Register (hex) Sub-carrier Freq. BURPHM BURPHL SYSPHM SYSPHL FREQM FREQ2 (MHz) 27 26 25 24 23 22 3.57954500 3.57954500 3.57954500 4.43361875 4.43361875 4.43361875 3.57561149 3.57561149 3.57561149 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4A 43 40 4C 54 4B 49 43 40 AA E0 00 F3 13 AA 45 DF 10 FREQ3 FREQL 21 20 AA F8 00 18 15 C6 00 3F 66 AB 3E 00 19 96 A1 51 D7 F5 Standard NTSC sqr. pixel NTSC CCIR-601 NTSC 4x fSC PAL sq. pixel PAL CCIR-601 PAL 15 Mpps PAL-M sq. pixel PAL-M CCIR-601 PAL-M 4x fSC 33 TMC22091/TMC22191 PRODUCT SPECIFICATION SCH Phase Error Correction SCH refers to the timing relationship between the 50% point of the leading edge of horizontal sync and the positive or negative zero-crossing of the color burst subcarrier reference. SCH error is usually expressed in degrees of subcarrier phase. In PAL, SCH is defined for line 1 of field 1, but since there is no color burst on line 1, SCH is usually measured at line 7 of field 1. The need to specify SCH relative to a particular line in PAL is due to the 25 Hz offset of PAL subcarrier frequency. Since NTSC has no such 25 Hz offset, SCH applies to all lines. The SCH relationship is only important in the TMC22x91 when two video sources are being combined or if the composite video output is externally combined with another video source. In these cases, improper SCH phasing will result in a noticeable horizontal jump of one image with respect to another and/or a change in hue proportional to the SCH error between the two sources. SCH phasing can be adjusted by modifying BURPH and SYSPH values by equal amounts. SCH is advanced/delayed by one degree by increasing/decreasing the value of BURPH and SYSPH by approximately B6h. An SCH error of 15° is corrected with SYSPH and BURPH offsets of AAAh. (Figure 11), the luminance component stair-step signal at the LUMA output, and the chrominance component on the CHROMA output. The six colors are 100% saturated PAL and 75% saturated for NTSC. The percentage color saturation is selectable via Misc. Control Register 0E, bit 0. The color bar test pattern comprises eight equal-width bars during VA, the active video period. The Timing Register value for CBL is found from: VA + 7 CBL = ----------------8 If CBL is larger than this, the color bars are truncated at the end of VA. If CBL is smaller than VA/8, the color bar sequence will repeat, starting with another white bar. From left to right color bars 1 to 8 should be white, yellow, cyan, green, magenta, red, blue, and black. The modulated ramp waveform is enabled by setting the Format Control Register to 30h. It comprises constant-amplitude and constant-phase subcarrier modulation superimposed on a linear ramp which slews from black to white during the active video portion of each horizontal line (Figure 12). This waveform is useful in making differential gain and differential phase measurements. Differential gain is a measure of the variation in saturation of a color as the luminance component is varied from black to white. Differential phase is a measure of the variation in hue of a color as the luminance component is varied from black to white. Video Test Signals The TMC22x91 has two standard video test waveforms for evaluating video signal integrity. They are selected and controlled by the Format Control Register. Setting the Format Control Register bits 0, 4, and 5 LOW generates standard color bars at the COMPOSITE output 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 24387A Figure 8. 100% Color Bars With 100% and 75% Chrominance Saturation 34 PRODUCT SPECIFICATION TMC22091/TMC22191 Microprocessor Interface The microprocessor interface comprises 13-lines. Two address bits provide four addresses for device programming and CLUT/register management. Address bit 0 selects between control registers and CLUT memory. Address bit 1 selects between reading/writing the register addresses and reading/writing register or CLUT data. When writing, the address is presented along with a LOW on the R/W pin during the falling edge of CS. Eight bits of data are presented on D7-0 during the subsequent rising edge of CS. 24388A Figure 7. Modulated Ramp Waveform One additional falling edge of CS is needed to move input data to the assigned working registers. tPWLCS CS tSA R/W tHA tPWHCS A1-A0 tSD D7-D0 24323A tHD Figure 10. Microprocessor Port – Write Timing tPWLCS CS tSA R/W tHA tPWHCS A1-A0 tDOM D7-D0 24324A tHOM tDOZ Figure 11. Microprocessor Port – Read Timing 35 TMC22091/TMC22191 PRODUCT SPECIFICATION In read mode, the address is accompanied by a HIGH on the R/W pin during a falling edge of CS. The data output pins go to a low-impedance state tDOZ ns after CS falls. Valid data is present on D7-0 tDOM after the falling edge of CS. Because this port operates asynchronously with the pixel timing, there is an uncertainty in this data valid output delay of one PXCK period. This uncertainty does not apply to tDOZ. The RESET pin restores the TMC22x91 to field 1 line 1 and places the encoder in a power-down state (if HRESET is LOW). Bit 4 of the Global Control Register (SRESET) is set LOW. All other control words and CLUT contents are left unchanged. Returning RESET HIGH synchronizes the internal clock with PXCK and restores the device outputs to active states. and Blank Insert block are monitored. When the Control Register pointer is loaded with 60h, the D7-0 port will output 8-bit luminance pixels synchronous with respect to PXCK. To halt the pixel flow from D7-0, bring CS HIGH. Operational Timing The TMC22x91 operates in three distinct modes: 1. Master mode. The encoder independently produces all internal timing and provides digital sync to the host controller. Slave mode. The encoder accepts horizontal and vertical sync from the controller and synchronizes the video output accordingly. Genlock mode. The encoder accepts horizontal and vertical sync from the companion TMC22071 Genlocking Video Digitizer, synchronizes itself to the incoming video, and provides appropriate H Sync and V Sync to the host. It synchronizes Pixel Data input in two ways: a. Internal PDC. The encoder internally generates the Pixel Data Control (PDC) signal which calls for data input from the external pixel source. External PDC. The encoder receives a PDC signal from the host and accepts Pixel Data based on that input. 2. Reading Pixel Data from the D7-0 Port The microprocessor port of the TMC22x91 may be used to monitor digital video outputs. The eight MSBs of the upsampled and interpolated pixel data that go to the COMPOSITE D/A converter can also be accessed via the D7-0 port. When the Test Control Register is loaded with 28h and the Control Register pointer is loaded with 40h, the D7-0 port will output the 8-bit composite pixels synchronous with PXCK. To halt the pixel flow from D7-0, simply bring CS HIGH. Luminance pixel data may also be read from D7-0. In this case, the eight MSBs of luminance at the input of the Sync 3. b. 1 PXCK tSR RESET tHR tSR 2 3 24330A Figure 12. Reset Timing – PCK Synchronization Reset Timing The TMC22x91 operates from a master clock (PXCK) at twice the pixel rate. In Master mode, the PCK to PXCK timing relationship is set on the rising edge of RESET. In Figure 12, PCK is denoted by odd PXCK counts. When RESET is taken LOW with sufficient setup time (tSR) before a rising edge of PXCK, the internal state machines are reset and the device is put into a mode as dictated by the Global Control Register bits 0 and 4. In Master mode, when the RESET pin is taken HIGH, the internal clock timing is established. In Slave and Genlock mode, this timing is established by VHSYNC and GHSYNC respectively. The first PXCK following this RESET rising edge is designated as PXCK 1. Where it is significant, reference PXCK timing will be shown with numbered rising edges. A designation of 2N clocks refers to an even number of PXCK rising edges from device reset. If RESET is not shown and clock numbering does not refer to 2N, timing is relative to signals shown in the diagram only. Pixel Data Input Timing PXCK is internally divided by 2 to generate an internal pixel clock, PCK which is not accessible from the pins of the TMC22x91. To ensure the correct phase relationship between PCK and pixel data, PCK is locked to VHSYNC or GHSYNC (Slave or Genlock mode, respectively). In Master mode, VHSYNC is produced on the rising edge of PCK allowing external circuitry to synchronize the generation of pixel data and LDV which also operates at the rate of PCK. The rising edge of LDV clocks the 24-bit pixel data into three 8-bit registers while PCK clocks that data through the pixel data path within the TMC22x91. It is therefore necessary to meet the set-up and hold timing between pixel data and LDV as well as LDV and PCK as shown in Figure 13. 36 PRODUCT SPECIFICATION TMC22091/TMC22191 tPWHPX PXCK tSP VHSYNC (GHSYNC) 2N+1 tPWLPX 2N+2 tPWLVH 2N+3 PCK tXL LDV tSP PD KEY 24340A tPWHLDV tPWLLDV tHP Figure 13. Slave Mode PD Port Interface Timing (Genlock Mode) 0 PXCK 1 2 3 4 16 17 18 19 20 21 51 52 53 54 55 56 57 58 59 60 RESET VHSYNC COMPOSITE OUTPUT 50% Sync Amplitude 24353A Figure 14. Master Mode Timing Master Mode In Master mode, initial timing is determined from the RESET input, and subsequent cycles result from programmed values in the Timing Control Registers. The Horizontal Sync output, VHSYNC, goes LOW 18 PXCK clock cycles after the device is reset. The 50% point of the falling edge of sync LOW on line 4 of field 1 (NTSC) or line 1 of field 1 (PAL) occurs at the COMPOSITE and LUMA outputs 56 clocks after reset, or 38 clocks after VHSYNC. See Figure 14, Master Mode Timing. Slave Mode In Slave mode, the 50% point of the falling edge of sync occurs 46 PXCK clocks after the falling edge of VHSYNC, which is an input signal to the TMC22x91. This must be provided by the host to begin every line. If it is early, the line will be started early, maintaining the 52 clock delay to output. If it comes late, the front porch portion of the output waveform will be extended as necessary. See Figure 15, Slave Mode Timing. 37 TMC22091/TMC22191 2N+40 2N+41 2N+42 2N+43 2N+44 2N+45 2N+46 2N+47 2N+48 2N+49 2N+50 2N+51 PRODUCT SPECIFICATION 2N+52 2N+53 2N+54 2N+55 2N+53 2N+56 24355A 24356A 2N+0 2N+1 2N+2 2N+3 PXCK VHSYNC1 VVSYNC1 for field 1 COMPOSITE OUTPUT 2N+4 50% Sync Amplitude Figure 15. Slave Mode Timing 2N+10 2N+11 2N+12 2N+13 2N+14 2N+47 2N+48 2N+49 2N+50 2N+51 2N+52 PXCK GHSYNC VHSYNC COMPOSITE OUTPUT 50% Sync Amplitude Figure 16. Genlocked Mode Timing Genlocked Mode In Genlocked mode, the encoder receives sync signals over the GHSYNC and GVSYNC inputs, and provides VHSYNC and VVSYNC to the host. The 50% sync amplitude point occurs 50 PXCK clocks after GHSYNC goes LOW, while VHSYNC is produced at clock 13. If GHSYNC is late, the front porch is lengthened, if is is early, front porch is shortened. See Figure 16, Genlock Mode Timing. The position (number of PCK cycles) of the rising edge of PDC relative to the falling edge of VHSYNC can be found by summing SY, BU, BR, and CBP. See Figure 17. External Pixel Data Control When used as an input, PDC goes HIGH four PXCK cycles before the first valid pixel of a line is presented to the PD input port. If this signal is late (with respect to the horizontal blanking interval programmed in the timing control registers), the Color Back Porch (CBP) will be extended. If it is early, incoming pixel data will be ignored until the end of the CBP. Pixel Data Control The Pixel Data Control (PDC) signal determines the active picture area. It may be an input or an output, as determined by the Interface Control Register bit 1. 38 2N+54 2N+0 2N+1 2N+2 2N+3 2N+6 2N+7 2N+8 2N+9 PRODUCT SPECIFICATION TMC22091/TMC22191 2N+39 2N+40 2N+41 2N+42 2N+43 2N+44 2N+45 2N+46 2N+47 2N+48 2N+49 P24 2N+49 P24 PXCK PDC PD P1 P2 P3 P4 P19 P20 P21 P22 P23 COMPOSITE OUTPUT P1 PI1 POST-FILTER OUTPUT 24358A P2 PI2 P3 Figure 17. External Pixel Data Control Internal Pixel Data Control When programmed as an output, PDC goes HIGH four PXCK periods prior to the end of CBP (as programmed in the horizontal timing registers) which is also four PXCK cycles prior to required input of the first pixel of a line. Pixels produced by the encoder appear at the analog outputs (COMPOSITE, LUMA, CHROMA) 40 clocks after they are registered into the PD port. Note that the pixels enter at onehalf the PXCK rate. The encoded signal passes through interpolation filters which generate intermediate output values, improving the output frequency response and greatly simplifying the external reconstruction filter. The interpolated pixels are designated PI in the diagram. 2N+39 2N+40 2N+41 2N+42 2N+43 2N+44 2N+45 2N+46 2N+47 2N+48 PXCK PDC tDO PD P1 P2 P3 P4 P19 P20 P21 P22 P23 COMPOSITE OUTPUT P1 PI1 POST-FILTER OUTPUT 24357A P2 PI2 P3 Figure 18. Internal Pixel Data Control 2N+50 2N+0 2N+1 2N+2 2N+3 2N+4 2N+5 2N+6 2N+7 2N+8 2N+9 2N+50 2N+0 2N+1 2N+2 2N+3 2N+4 2N+5 2N+6 2N+7 2N+8 2N+9 39 TMC22091/TMC22191 PRODUCT SPECIFICATION Layering with the TMC22191 Layering is a video production process where various images or patterns are superimposed (keyed) over each other to form a layered composite of the input images. Four layers with the following priority are provided by the TMC22191: 1. 2. The DOWNSTREAM KEY layer keys over all other layers. The FOREGROUND layer keys over MIDGROUND and BACKGROUND, but not over DOWNSTREAM KEY. The MIDGROUND layer keys over BACKGROUND, but not over FOREGROUND or DOWNSTREAM KEY. The BACKGROUND layer never keys over any other layer. A 4-Layer Example For this layering example, a BACKGROUND image is generated. This image comprises shaded matte levels varying from black at the top of the screen to white at the bottom. This could just as well be a color image which will be seen wherever no other image appears through the layering process. The MIDGROUND image comprises a happy face superimposed over a white rectangle. Only the happy face and the white rectangle are of interest for this image and therefore, the portion of the image outside that area will be replaced by the BACKGROUND image when MIDGROUND is keyed over BACKGROUND. A key signal is generated on a pixelby-pixel basis. It indicates which image is active. The key signal for keying MIDGROUND over BACKGROUND is shown to the right of the MIDGROUND image. This represents a single bit signal mapped over the image. When the signal is black (logic LOW), the MIDGROUND image is active, when it is white (logic HIGH), the BACKGROUND is active. The results of layering MIDGROUND over BACKGROUND images are shown in the 2-layer composite image Figure 19. 3. 4. It is important not to confuse layers with sources. The TMC22191 can be programmed to assign any of its input sources (RGB, YCRCB, CVBS bus, Overlay bits) to any of the four layers. The ability to combine various video sources into a 4-layer composite image is a very powerful tool in the production of live video. The TMC22191 performs layering operations entirely in the digital domain, enabling precise digital control. BACKGROUND KEY 2-LAYER COMPOSITE MIDGROUND 27036A Figure 19. 2-Layer Image Construction A FOREGROUND image comprises a shaded matte rectangle with "HI KIDS !" alpha characters in its center. This is to be superimposed over the previous 2-layer composite image. The key signal needed for superimposing FOREGROUND over other images is shown to the right of the FOREGROUND image. This represents a single bit signal mapped over the image. When the signal is black (logic LOW), the FOREGROUND image is active, when it is white (logic HIGH), the composite image is active. A new 3-layer composite image, FOREGROUND over MIDGROUND over BACKGROUND, is shown in Figure 20. 40 PRODUCT SPECIFICATION TMC22091/TMC22191 2-LAYER COMPOSITE KEY 3-LAYER COMPOSITE HI KIDS ! FOREGROUND HI KIDS ! HI KIDS ! 27037A Figure 20. Adding a 3rd Layer A DOWNSTREAM KEY image comprises the white alpha characters "HAPPY FACE", and black alpha characters "Time". This is to be superimposed over the previous 3-layer composite image. The key signal needed for superimposing DOWNSTREAM KEY image over the other composite images is shown to the right. This represents a single bit signal mapped over the image. When the signal is black (logic LOW), the DOWNSTREAM KEY image is active, when it is white (logic HIGH), the previous composite image is active. The final 4-layer composite image, DOWNSTREAM KEY over FOREGROUND over MIDGROUND over BACKGROUND, is shown in Figure 21. In this illustration, all four source images are static (not moving). The images input to the TMC22191 can just as well be "live" (from video camera or VCR sources) as long as: • Data from those sources is in an input format that the TMC22191 can accept, and • The sources either synchronize the TMC22191 (Genlock mode) or are synchronized by the TMC22191 (Master or Slave mode). Key signals may be generated external to the TMC22191 (Hardware Keying) and use the KEY input pin for control. Key signals may also be generated within the TMC22191 (Data Keying) by the comparison of input color data with color data stored in the TMC22191. 3-LAYER COMPOSITE HI KIDS ! KEY 4-LAYER COMPOSITE DOWNSTREAM KEY HAPPY FACE TIME HI KIDS ! HAPPY FACE TIME 27038A HAPPY FACE TIME Figure 21. Adding a 4th Layer 41 TMC22091/TMC22191 PRODUCT SPECIFICATION 2-Layer Keying with the TMC22091 The TMC22091 facilitates the keying of PD port input data over the CVBS bus input data. Keying is controlled on a pixel-by-pixel basis by either the KEY input pin or the internal Data Key. The first two layers in the previous 4-Layer Example apply to the TMC22091. The result of keying is an effect where a MIDGROUND source image (i.e. Happy Face from PD data) is superimposed over a BACKGROUND source image (i.e. variable matte color from CVBS data). Assigning Video Sources to Layers with the TMC22191 Digital video inputs to the TMC22191 (PD, CVBS, Overlay) are assigned to the four layers by choosing one of the 16 modes of the Layering Control Register. OVERLAY is always keyed (switched on a pixel-by-pixel basis from active to transparent) by the OL4-0 inputs. OVERLAY can not be programmed to the BACKGROUND layer. The CVBS digital video bus can be assigned to any of the four layers and is keyed by the KEY input signal or internal Data Key. In modes 0 thru 7, the CLUTs are not bypassed and the BYPASS input is ignored. Table 14. Layer Assignments, Image Sources, and Keying Controls (TMC22191) LCR 04 LAYMODE 0 1 2 3 4 5 6 7 8 9 A B C D E F Background Image Source PD(YCBCR, RGB, CI) PD(YCBCR, RGB, CI) PD(YCBCR, RGB, CI) PD(YCBCR, RGB, CI) CVBS CVBS PD(YCBCR, RGB, CI) PD(YCBCR, RGB, CI) PD(YCBCR, CI) PD(RGB) PD(RGB) PD(RGB) PD(RGB) CVBS CVBS PD(RGB) Midground Image Source CVBS CVBS CVBS CVBS OVERLAY PD(YCBCR, RGB, CI) CVBS CVBS CVBS PD(YCBCR, CI) CVBS CVBS PD(YCBCR, CI) PD(RGB) OVERLAY OVERLAY Keying Control KEY or Data Key KEY or Data Key KEY KEY OL4-0 KEY or Data Key KEY KEY KEY or Data Key BYPASS KEY or Data Key KEY or Data Key BYPASS KEY OL4-0 OL4-0 CVBS PD(YCBCR, CI) OVERLAY OVERLAY PD(YCBCR, CI) PD(RGB) CVBS Foreground Image Source: — OVERLAY PD(YCBCR, RGB, CI) PD(YCBCR, RGB, CI) PD(YCBCR, RGB, CI) OVERLAY OVERLAY OVERLAY Keying Control — OL4-0 Data Key Data Key KEY or Data Key OL4-0 OL4-0 OL4-0 — KEY or Data Key BYPASS OL4-0 OL4-0 BYPASS KEY KEY or Data Key Downstream Key Image Source: — — OVERLAY OVERLAY — — Keying Control — — OL4-0 OL4-0 — — PD(YCBCR, RGB, CI) Data Key PD(YCBCR, RGB, CI) Data Key — OVERLAY OVERLAY PD(YCBCR, CI) CVBS OVERLAY PD(YCBCR, CI) PD(YCBCR, CI) — OL4-0 OL4-0 BYPASS KEY or Data Key OL4-0 BYPASS BYPASS Notes: 1. For LAYMODE = 0 to 7, Pixel Data always passes through the CLUTs. FORMAT, INMODE, and the BYPASS pin selects the input format for PD23-0 according to Table 6. 2. For LAYMODE = 8 to F and BYPASS = HIGH, Data Key is disabled. 3. Asserting the signal listed under "Keying Control:" enables the corresponding "Signal Source:". Signals with " " are asserted by a logic LOW. 42 PRODUCT SPECIFICATION TMC22091/TMC22191 Hardware Keying The KEY input switches the COMPOSITE D/A converter input from the luminance and chrominance combiner output to the CVBS data bus on a pixel-by-pixel basis. This is a "soft" switch, executed over four PXCK periods to minimize out-of-band spurious signals. The video signal from the CVBS bus can only present on the COMPOSITE output. The CHROMA and LUMA outputs continue to present encoded PD port data when CVBS is active. Hardware keying is enabled by the Key Control Register bit 6. Normally, keying is only effective during the Active Video portion of the waveform as determined by the VA registers 15 and 18. The Horizontal Blanking interval is generated by the encoder state machine even if the KEY signal is held HIGH through Horizontal Blanking. However, it is possible to allow digital Horizontal Blanking to be passed through from the CVBS bus to the COMPOSITE output by setting Key Control Register bit 5 HIGH. In this mode, KEY is always active, and may be exercised at will. The KEY input is registered into the encoder just like Pixel Data is clocked into the PD port. It may be considered a 25th Pixel Data bit. It is internally pipelined, so the midpoint of the key transition occurs at the output of the pixel that was input at the same time as the KEY signal. Data Keying Data Keying internally generates a Key signal that acts exactly as the external KEY signal. There are three Key Value Registers 05, 06, and 07 that are matched against the input data to the three tables in the CLUT. These tables are designated D, E, and F. They contain different information depending on the input mode selected as shown in Table 16. 0 PXCK 1 2 3 4 5 6 7 8 9 38 39 40 41 42 43 44 45 46 47 48 49 CVBS VN+2 VN+3 VN+4 VN+5 VN+6 VN+25 VN+26 VN+27 VN+28 VN+29 VN+30 KEY * PN PN+1 PN+2 PN+3 PN+4 PN+23 PN+24 PN+25 PN+26 PN+27 PN+28 PD KEY MIDPOINT COMPOSITE OUTPUT PIN+2VIN+1 PIN+3VIN+2 PN+3VIN+2 PIN+1 PN+1 PN+2 Figure 22. Hardware Keying The key registers may be individually enabled using bits 3,2,1 of the Key Control Register. Bit 4 of the same register enables/disables Data Keying in its entirety. Data Keying and Hardware Keying are logically ORed: when both are enabled, either one will result in a key switch to the CVBS channel. The key comparison is based on the input data to the tables in the CLUT. When operating in color-index mode, all three tables receive the same input value, so any one of the three registers is sufficient to identify a key value. The outputs of all enabled key registers are ANDed to produce the KEY signal. If more than one key register are enabled and their key values are not identical, no key will be generated. Table 16. Table D, E, F Contents Mode GBR RGB YCBCR CI Table D Green Red Y CI Table E Blue Green CB CI Table F Red Blue CR CI VN+3 24359A PIN PN five PXCK cycles when * KEY is advancedOE bit 4 is HIGH (TMC22191). Control Register 43 TMC22091/TMC22191 PRODUCT SPECIFICATION Genlock Interface The TMC22x91 can process digital composite video connected to its CVBS port. It has been designed to couple tightly with the companion TMC22071 Genlocking Video Digitizer, but it will work with other sources as well. The digital composite video has to be in standard 8-bit binary format at a PXCK/2 rate. Synchronization with the internal PXCK/2 is established by the phasing of the GHSYNC input, as shown in Figures 24 and 25. Subcarrier frequency and phase data are transmitted to the encoder over the CVBS bus as 4-bit nibbles on CVBS3-0 during the horizontal sync period. Field identification is also required for the TMC22x91 internal sync generator. The 14th nibble of the sequence contains no relevant data. 0 PXCK 1 2 3 4 5 6 7 8 9 38 39 40 41 42 43 44 45 46 47 48 49 CVBS VN+2 VN+3 VN+4 VN+5 VN+6 VN+25 VN+26 VN+27 VN+28 VN+29 VN+30 PD PN PN+1 PN+2 PN+3 PN+4 PN+23 PN+24 PN+25 PN+26 PN+27 PN+28 KEY MIDPOINT FIRST KEY WORD COMPOSITE OUTPUT PIN+2VIN+5 PIN+3VIN+6 PN+3VIN+6 PIN+1 PN+1 PN+2 Figure 23. Data Keying PXCK tSGI GHSYNC 2N+1 tHGI 2N+2 tSGI CVBS7-0 tHGI VN+7 24360A PIN PN 2N+3 24341A Figure 24. Genlock Interface Timing 44 PRODUCT SPECIFICATION TMC22091/TMC22191 PXCK 0 GHSYNC 1 2 3 4 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 CVBS7-0 PIXEL PIXEL PIXEL FID f23:20 f19:16 f15:12 f11:8 f7:4 FREQUENCY f3:0 φ23:20 φ19:16 φ15:12 φ11:8 φ7:4 φ3:0 PHASE PIXEL PIXEL FIELD IDENTIFICATION 24383A Figure 25. Frequency/Phase Data Transfer Filtering The TMC22x91 incorporates internal digital filters to establish appropriate bandwidths and simplify external analog filter designs. Since these are fixed-coefficient digital filters, their filter characteristics depend upon clock rate. Figures 26 and 27 show the frequency response for two pixel rates, 12.27 MHz and 14.75 MHz. 0 -10 Attenuation (dB) -20 -30 -40 -50 -60 -70 -80 -90 f = 12.27 Mpps Color-Difference Low-Pass Filters The color-difference low-pass filters in the TMC22x91 establish chrominance bandwidths which meet the specifications outlined in CCIR Report 624-3, Table II, Item 2.6, for system I over a range of pixel rates from 12.27 Mpps to 14.75 Mpps. Equal bandwidth is established for both colordifference channels. 0 -10 -20 Attenuation (dB) -30 -40 -50 -60 -70 -80 -90 0 CCIR Rep 624 Specification f = 14.75 Mpps 0 3 6 9 12 15 24394A CCIR Rep 624 Specification Frequency (MHz) f = 14.27 Mpps Figure 27. Chroma Modulator and Luminance Interpolation Filter Full Spectrum Response f = 12.27 Mpps 0 Attenuation (dB) -1 -2 -3 -4 f = 14.75 Mpps 1 2 3 4 5 6 7 8 24363A Frequency (MHz) f = 12.27 Mpps Figure 26. Color-Difference Low-Pass Filter Response Interpolation Filters The Chroma Modulator output and the luminance data path are digitally filtered with sharp-cutoff low-pass interpolation filters. These filters ensure that aliased subcarrier, chrominance, and luminance frequencies are sufficiently suppressed in the frequency band above base-band video and below the pixel frequency (fS/4 to 3fS/4, where fS is the PXCK frequency). 0 1 2 3 4 5 6 7 24365A Frequency (MHz) Figure 28. Chroma Modulator and Luminance Interpolation Filter Passband Detail All digital-to-analog reconstruction systems exhibit a high frequency roll-off as a result of the zero-order hold characteristic of D/A converters. This response is commonly referred to as a sin(x)/x response. It is a function of the sampling rate of the output D/A. 45 TMC22091/TMC22191 PRODUCT SPECIFICATION The digital interpolation filters in TMC22x91 convert the data stream to a sample rate of twice the pixel rate. As shown in Figures 27 and 28, the filters decrease the sin(x)/x rolloff and the output spectrum between fS/4 and 3fS/4 contains very little energy. Since there is so little signal energy in this frequency band, the demands placed on the output reconstruction filter are greatly reduced. The output filter needs to be flat to fS/4 and have good rejection at 3fS/4. The relaxed requirements greatly simplify the design of a filter with good phase response and low group delay distortion. A small amount of peaking may be used to compensate residual sin(x)/x rolloff. JTAG Test Interface The JTAG test port accesses registers at every digital I/O pin except the JTAG test port pins. Table 16 shows the sequence of the test registers. The register number (Reg) indicates the order in which the register data is loaded and read (Reg 1 is loaded and read first, therefore it is at the end of the serial path). The scan path is 59 registers long. The six TEST pins of the TMC22091 function as JTAG registers. The JTAG port is a 4-line interface, following IEEE Std. 1149.1-1990 specifications. The Test Data Input (TDI) and Test Mode Select (TMS) inputs are referred to the rising edge of the Test ClocK (TCK) input. The Test Data Output (TDO) is referred to the falling edge of TCK. Table 16. JTAG Interface Connections Reg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Pin 28 29 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 Signal BYPASS (TEST) OL4 (TEST) CVBS7 CVBS6 CVBS5 CVBS4 OL3 (TEST) OL2 (TEST) OL1 (TEST) OL0 (TEST) PD23 PD22 PD21 PD20 PD19 PD18 PD17 PD16 PD15 PD14 Reg 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Pin 62 63 66 67 68 69 70 71 72 73 74 75 76 77 78 79 82 83 84 1 Signal PD13 PD12 PD11 PD10 PD9 PD8 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 LDV PXCK GVSYNC GHSYNC CVBS3 CVBS2 Reg 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 Pin 2 3 4 5 6 7 8 9 11 12 13 14 15 16 17 18 19 20 21 Signal CVBS1 CVBS0 KEY RESET CS R/W A1 A0 PDC VHSYNC VVSYNC D7 D6 D5 D4 D3 D2 D1 D0 46 PRODUCT SPECIFICATION TMC22091/TMC22191 tPWLTCK TCK tSTP TDI TMS tHOTP TDO tHTP tPWHTCK tDOTP 24333A Figure 29. JTAG Test Port Timing Equivalent Circuits VDD n Substrate VDD RREF VREF n VDD p COMPOSITE LUMA CHROMA 27012A 27013A Figure 30. Equivalent Analog Input Circuit Figure 31. Equivalent Analog Output Circuit n Substrate VDD VDD p Input n p Output n 27014A 27011A Figure 32. Equivalent Digital Input Circuit Figure 33. Equivalent Digital Output Circuit 47 TMC22091/TMC22191 PRODUCT SPECIFICATION tDOM CS tHOM 0.5V Hi-Z D7-0 0.5V 2.0V 0.8V 27029A tDOZ Figure 34. Transition Levels for Three-State Measurements Absolute Maximum Ratings (beyond which the device may be damaged)1 Parameter Power Supply Voltage Digital Inputs Applied Voltage2 Forced Current3,4 Digital Outputs Applied Voltage2 Forced Current3,4 Short Circuit Duration (Single output in HIGH state to GND) Analog Output Short Circuit Duration (Single output to GND) Temperature Operating, ambient Operating, junction, plastic package Lead, soldering (10 seconds) Vapor phase soldering (1 minute) Storage -65 -20 110 140 300 220 150 °C °C °C °C °C -0.5 -20.0 VDD+0.5 20.0 1 Infinite V mA second -0.5 -20.0 VDD+0.5 20.0 V mA Min. -0.5 Max. 7.0 Unit V Notes: 1. Absolute maximum ratings are limiting values applied individually while all other parameters are within specified operating conditions. Functional operation under any of these conditions is NOT implied. 2. Applied voltage must be current limited to specified range, and measured with respect to GND. 3. Forcing voltage must be limited to specified range. 4. Current is specified as conventional current, flowing into the device. 48 PRODUCT SPECIFICATION TMC22091/TMC22191 Operating Conditions Parameter VDD VIH Power Supply Voltage Input Voltage, Logic HIGH TTL Compatible Inputs, all but TCK TTL Compatible Input TCK CMOS Compatible Inputs VIL Input Voltage, Logic LOW TTL Compatible Inputs CMOS Compatible Inputs IOH IOL VREF IREF RREF ROUT TA fPXL fPXCK tPWHPX tPWLPX tSP tHP tHP tXL tPWHLDV tPWLLDV tPWLVH tPWHVV tSGI tHGI tPWLCS tPWHCS tSA tHA tSD tHD Output Current, Logic HIGH Output Current, Logic LOW External Reference Voltage D/A Converter Reference Current, VREF = Nom. (IREF = VREF / RREF, flowing out of the RREF pin) Reference Resistor, VREF = Nom. Total Output Load Resistance Ambient Temperature, Still Air Pixel Rate Master Clock Rate, 2x pixel rate PXCK Pulse Width, HIGH PXCK Pulse Width, LOW Setup Time Hold Time, PD and KEY Hold Time, PDC, VHSYNC, VVSYNC Delay Time, LDV LDV Pulse Width, HIGH LDV Pulse Width, LOW VHSYNC Pulse Width, LOW VVSYNC Pulse Width, LOW Setup Time, GHSYNC, GVSYNC, CVBS Hold Time, GHSYNC, GVSYNC, CVBS CS Pulse Width, LOW CS Pulse Width, HIGH Address Setup Time Address Hold Time Data Setup Time (write) Data Hold Time (write) 0 12.27 24.54 10 10 12 0 5 10 15 10 6 0.5 10 0 55 30 10 0 15 0 15 3 281 392 37.5 70 15 30 588 Ω Ω °C Mpps MHz ns ns ns ns ns ns ns ns PXCK periods H ns ns ns ns ns ns ns ns 2.1 1.235 3.15 4.4 GND GND 0.8 (1/3)VDD -2.0 4.0 V V mA mA V mA 2.0 2.5 (2/3)VDD VDD VDD VDD V V V Min. 4.75 Nom. 5.0 Max. 5.25 Units V Pixel Interface For PD, VVSYNC, VHSYNC, PDC, KEY Genlock Interface Microprocessor Interface 49 TMC22091/TMC22191 PRODUCT SPECIFICATION Operating Conditions (continued) Parameter tSR tHR fTCK tPWLTCK tPWHTCK tSTP tHTP Reset Setup Time Reset Hold Time Test Clock (TCK) Rate TCK Pulse Width, LOW TCK Pulse Width, HIGH Test Port Setup Time, TDI, TMS Test Port Hold Time, TDI, TMS 10 25 10 3 Min. 24 2 20 Nom. Max. Units ns ns MHz ns ns ns ns JTAG Interface Note: 1. Timing reference points are at the 50% level. Electrical Characteristics Parameter IDD IDDQ VRO IBR IIH IIL VOH VOL IOZH IOZL CI CO VOC ROUT COUT Power Supply Current1 Power Supply (D/A disabled) Current1 Conditions VDD = Max, fPXCK = 30MHz VDD = Max, fPXCK = 30MHz 0.988 VREF = Nom VDD = Max, VIN = VDD VDD = Max, VIN = 0V IOH = Max IOL = Max VDD = Max, VIN = VDD VDD = Max, VIN = GND TA = 25°C, f = 1MHz TA = 25°C, f = 1MHz -0.3 15 IOUT = 0 mA, f = 1 MHz 15 25 4 10 2.0 2.4 0.4 10 -10 10 1.235 100 10 -10 Min. Typ. 250 Max. 300 60 1.482 Units mA mA V µA µA µA V V µA µA pF pF V kΩ pF Voltage Reference Output Input Bias Current, VREF Input Current, Logic HIGH Input Current, Logic LOW Output Voltage, Logic HIGH Output Voltage, Logic LOW Hi-Z Leakage current, HIGH Hi-Z Leakage current, LOW Digital Input Capacitance Digital Output Capacitance Video Output Compliance Voltage Video Output Resistance Video Output Capacitance Note: 1. Typical IDD with VDD = +5.0 Volts and TA = 25°C, Maximum IDD with VDD = +5.25 Volts and TA = 0°C. 50 PRODUCT SPECIFICATION TMC22091/TMC22191 Switching Characteristics Parameter PIPES tDOZ tDOM tHOM tDOTP tHOTP tDOS tR tF tDOV Pipeline Delay 3 Conditions PD to Analog Out Min. 44 6 10 Typ. 44 Max. 44 23 100 30 Units PXCK periods ns ns ns ns ns Output Delay, CS to low-Z Output Delay, CS to Data Valid4 Output Hold Time, CS to hi-Z Output Delay, TCK to TDO Valid Output Hold Time, TCK to TDO Valid Output Delay D/A Output Current Risetime D/A Output Current Falltime Analog Output Delay PXCK to VHSYNC, VVSYNC, PDC 10% to 90% of full-scale 90% to 10% of full-scale 5 25 2 2 20 ns ns ns ns Notes: 1. Timing reference points are at the 50% level. 2. Analog CLOAD < 10 pF, D7-0 load < 40 pF. 3. Pipeline delay, with respect to PXCK, is a function of the phase relationship between the internally generated PCK (PXCK/2) and PXCK, as established by the hardware reset. 4. tDOM = 1 PXCK + 54 ns = 100 ns worst-case at PXCK = 24.54 MHz. System Performance Characteristics Parameter RES ELI ELD EG dp dg SKEW PSRR D/A Converter Resolution Integral Linearity Error Differential Linearity Error Gain Error Differential Phase Differential Gain CHROMA to LUMA Output Skew Power Supply Rejection Ratio CCOMP = 0.1 µF, f = 1kHz PXCK = 24.54 MHz, 40 IRE Ramp3 PXCK = 24.54 MHz, 40 IRE Ramp3 0.5 0.9 0 0.5 2 Conditions Min. 10 Typ. 10 Max. 10 0.25 0.20 ±10 Units Bits % % % FS degree % ns %/ %VDD Notes: 1. TTL input levels are 0.0 and 3.0 Volts, 10%-90% rise and fall times