HL01R15S05

Product Data Sheet 1 WATT REGULATED DC/DC CONVERTER HL01R FEATURES G LOW COST G NON-CONDUCTIVE CASE G INTERNAL INPUT AND OUTPUT FILTERING G SHORT CIRCUIT PROTECTED G BUILT IN STANDOFFS G INDUSTRY STANDARD PINOUT DESCRIPTION The HL01R Series uses advanced circuit design and packaging technology to realize superior reliability and performance. A 125kHz push-pull oscillator is used in the input stage. Beat-frequency oscillator problems are reduced when using the HL01R Series with high frequency isolation amplifiers. Reduced parts count and all surface mount construction add to the reliability of the HL01R Series. The use of surface mount devices and magnetics eliminate hand soldering operations. This "hands-free" construction increases quality and reliability while keeping cost low. ABSOLUTE MAXIMUM RATINGS Internal Power Dissipation.......................................................1.2W Short Circuit Duration....................................................Continuous Lead Temperature (soldering, 10 seconds max)................+300°C ORDERING INFORMATION HL01R xxyzz Y/Z /H Device Family HL Indicates DC/DC Converter Model Number Where: xx = Input Voltage y = Number or Outputs (Single "S", Dual "D") zz = Output Voltage Package Option Screening Option DIP Package only * *Note: Refer to Reflow Profile for SMD Models. TYPICAL PERFORMANCE CURVES Specifications typical at TA = +25°C, nominal input voltage, rated output current unless otherwise specified. EFFICIENCY vs LOAD 60% 50% Efficiency (%) 40% 30% 20% 10% 0% 0% 25% 50% Load (mA) 75% 100% Internet: http://www.cdpowerelectronics.com Power Electronics Division, United States 3400 E Britannia Drive, Tucson, Arizona 85706 Phone: 800.547.2537 Fax: 520.770.9369 Power Electronics Division, Europe C&D Technologies (Power Electronics) Ltd. 132 Shannon Industrial Estate , Shannon, Co. Clare, Ireland Tel: +353.61.474.133 Fax:+353.61.474.141 Page 0 HL01RrevD,10/97 ELECTRICAL SPECIFICATIONS Specifications typical at TA = +25°C, nominal input voltage, rated output current unless otherwise specified. NOMINAL INPUT VOLTAGE MODEL HL01R05S05 HL01R05S12 HL01R05S15 HL01R12S05 HL01R12S12 HL01R12S15 HL01R15S05 HL01R15S12 HL01R15S15 HL01R24S05 HL01R24S12 HL01R24S15 HL01R05D05 HL01R05D12 HL01R05D15 HL01R12D05 HL01R12D12 HL01R12D15 HL01R15D05 HL01R15D12 HL01R15D15 HL01R24D05 HL01R24D12 HL01R24D15 (VDC) 5 5 5 12 12 12 15 15 15 24 24 24 5 5 5 12 12 12 15 15 15 24 24 24 RATED OUTPUT VOLTAGE (VDC) 5 12 15 5 12 15 5 12 15 5 12 15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 RATED OUTPUT CURRENT (mA) 200 83 67 200 83 67 200 83 67 200 83 67 ±100 ±41 ±33 ±100 ±41 ±33 ±100 ±41 ±33 ±100 ±41 ±33 INPUT CURRENT MIN LOAD (mA) 50 50 50 40 40 40 30 30 30 20 20 20 50 50 50 40 40 40 30 30 30 20 20 20 RATED LOAD (mA)(%) 400 400 400 160 160 160 130 130 130 80 80 80 425 400 400 185 160 160 145 130 130 90 80 80 58 52 52 58 52 52 58 52 52 58 52 52 45 53 53 45 53 53 45 53 53 45 53 53 EFFICIENCY Note: Other input to output voltages may be available. Please contact factory. COMMON SPECIFICATIONS Specifications typical at TA = +25°C, nominal input voltage, rated output current unless otherwise specified. PARAMETER INPUT Voltage Range CONDITIONS MIN 4.75 11.4 14.25 22.8 TYP 5 12 15 24 30 MAX 5.25 12.6 15.75 25.2 100 UNITS VDC VDC VDC VDC mAp-p Reflected Ripple Current ISOLATION Rated Voltage Test Voltage Resistance Capacitance Leakage Current OUTPUT Rated Power Voltage Setpoint Accuracy Temperature Coefficent Ripple & Noise Line Regulation Load Regulation GENERAL Switching Frequency Package Weight MTTF per MIL-HDBK-217, Rev. F Ground Benign TEMPERATURE Specification Operation Storage 60 Hz, 10 Seconds 500 500 1 25 2 VISO= 240VAC, 60Hz 10 VDC Vpk GΩ pF µArms BW = DC to 10MHz BW =10Hz to 2MHz High Line to Low Line Rated Load to No Load 1 ±3 ±0.01 30 1 ±0.1 ±0.3 125 10 ±5 ±0.02 100 10 ±0.3 ±0.5 W % %/°C mVp-p mVrms % % kHz g kHr Circuit Stress Method 675 -25 -40 -40 +70 +85 +110 °C °C °C Page 2 HL01RrevD,10/97 MECHANICAL Package/Pinout "Y" and "Z" 1.285±0.010" (32.64±0.25) 1514 13 1.285±0.010" (32.64±0.25) 2423 22 2423 22 1514 13 TOP VIEWS 0.525±0.010" (13.34±0.25) 0.525±0.010" (13.34±0.25) HL01RxxyzzY HL01RxxyzzZ 0.695±0.015" (17.65±0.38) 123 10 11 12 123 10 11 12 0.375±0.005" (9.52±0.13) 0.015±0.005" (0.38±0.13) 0.020±0.002" (0.51±0.05) SIDE VIEWS 0.375±0.005" (9.52±0.13) 0.015±0.005" (0.38±0.13) 0.100±0.010" (2.54±0.25) 0.020±0.002" (0.51±0.05) 0.100±0.010" (2.54±0.25) END VIEWS 0°-15° 0.600" (15.24) 0.125+0.030" -0.000" (3.18+0.76) ( -0.00) 0.014±0.002" (0.36±0.05) .015±.010" (.38±.25) DIP PACKAGE NU = Do Not Use. NC = No Internal Connection. Duplicate pin functions are internally connected. All dimensions are in inches (millimeters). GRID: 0.100 inches (2.54 millimeters) Typically Marked with: specific model ordered, date code, job code and Logo. SMD PACKAGE PIN CONNECTIONS PIN# 1 2 3 10 11 12 13 14 15 22 23 24 SINGLES +VIN NU NU -VOUT +VOUT -VIN -VIN +VOUT -VOUT NU NU +VIN DUALS +VIN -VOUT Common Common +VOUT -VIN -VIN +VOUT Common Common -VOUT +VIN RECOMMENDED LAND PATTERN 0.100" (2.54) 2423 22 1514 13 RECOMMENDED REFLOW PROFILE 30 sec MAX (>220°C) 250 235 °C MAX 220 200 190 TEMPERATURE (°C) 0.730" (18.54) 0.040" (1.02) 123 0.080" (2.03) 150 10 11 12 100 1.150" (29.21) 90 sec MAX (>190°C) 50 TIME (seconds) HL01RrevD,10/97 Page 2 Page 4 HL01RrevD,10/97