HL02U15S05

TECHNOLOGIES Product Data Sheet 2 WATTS UNREGULATED DC/DC CONVERTER HL02U FEATURES q q q q LOW COST INTERNAL FILTERING SURFACE MOUNT CONSTRUCTION TEMPERATURE RANGE: -25°C TO +70°C q HIGH EFFICIENCY q LOW OUTPUT NOISE q NON-CONDUCTIVE CASE DESCRIPTION The HL02U Series offers an extensive selection of input and output voltages to choose from. These miniature, unregulated DC/DC converters come in 24-pin DIP and SMD packages. This small size is possible through the use of surface mount manufacturing technologies. The HL02U Series utilizes a 110KHz push-pull oscillator in the input stage with internal filtering to reduce the output noise while maintaining good efficiency. The use of surface mount construction and automated manufacturing processes increase consistency and reliability while reducing overall cost. ABSOLUTE MAXIMUM RATINGS Internal Power Dissipation...................................................................0.90W Short Circuit Duration.........................................................................30 Sec Lead Temperature (soldering, 10 seconds max)..............................+300°C * * Note: Refer to Reflow Profile for SMD Models. ORDERING INFORMATION HL02U xxyzz Y/Z /H Device Family HL Indicates DC/DC Converter Model Number Where: xx = Input Voltage y = Number or Outputs (Single "S", Dual "D") zz = Output Voltage Package Option Screening Option DIP Package only Internet: http://www.cdpowerelectronics.com Power Electronics Division, United States 3400 E Britannia Drive, Tucson, Arizona 85706 Phone: 800.547.2537 Fax: 520.770.9369 Power Electronics Division, Europe C&D Technologies (Power Electronics) Ltd. 132 Shannon Industrial Estate, Shannon, Co. Clare, Ireland Tel: +353.61.474.133 Fax:+353.61.474.141 Page 1 HL02UrevD,10/97 ELECTRICAL SPECIFICATIONS Specifications typical at TA = +25°C, nominal input voltage, rated output current unless otherwise specified. NOMINAL INPUT VOLTAGE MODEL HL02U05S05 HL02U05S12 HL02U05S15 HL02U12S05 HL02U12S12 HL02U12S15 HL02U15S05 HL02U15S12 HL02U15S15 HL02U24S05 HL02U24S12 HL02U24S15 HL02U05D05 HL02U05D12 HL02U05D15 HL02U12D05 HL02U12D12 HL02U12D15 HL02U15D05 HL02U15D12 HL02U15D15 HL02U24D05 HL02U24D12 HL02U24D15 (VDC) 5 5 5 12 12 12 15 15 15 24 24 24 5 5 5 12 12 12 15 15 15 24 24 24 RATED OUTPUT VOLTAGE (VDC) 5 12 15 5 12 15 5 12 15 5 12 15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 RATED OUTPUT CURRENT (mA) 400 167 133 400 167 133 400 167 133 400 167 133 ±200 ±83 ±67 ±200 ±83 ±67 ±200 ±83 ±67 ±200 ±83 ±67 INPUT CURRENT NO LOAD (mA) 40 40 40 30 30 30 30 30 30 20 20 20 40 40 40 30 30 30 30 30 30 20 20 20 RATED LOAD (mA) 540 480 480 230 210 210 190 170 170 125 110 110 540 490 490 230 210 210 190 170 170 120 110 110 EFFICIENCY (%) 74 83 83 72 79 79 70 78 78 72 78 78 74 82 82 72 79 79 70 78 78 72 78 78 COMMON SPECIFICATIONS Specifications typical at TA = +25°C, nominal input voltage, rated output current unless otherwise specified. PARAMETER INPUT Voltage Range CONDITIONS MIN 4.75 11.4 14.25 22.8 TYP 5 12 15 24 30 MAX 5.25 12.6 15.75 26.2 100 UNITS VDC Reflected Ripple Current ISOLATION Rated Voltage Test Voltage Resistance Capacitance Leakage Current OUTPUT Rated Power Voltage Setpoint Accuracy Temperature Coefficent Ripple & Noise Line Regulation Load Regulation GENERAL Switching Frequency Package Weight MTTF per MIL-HDBK-217, Rev. F Ground Benign mAp-p 60 Hz, 10 Seconds 500 500 1 25 2 2 ±3 ±0.02 50 10 ±1 ±3 110 12 VISO= 240VAC, 60Hz VDC Vpk GΩ pF µArms W % %/°C mVp-p mVrms %/% % kHz g kHr kHr ±5 100 ±1.5 ±15 BW = DC to 10MHz BW =10Hz to 2MHz High Line to Low Line Rated Load to 1/4 Load Circuit Stress Method TA = +25°C TA = +70°C -25 -40 -40 200 40 TEMPERATURE Specification Operation Storage +70 +85 +110 °C °C °C Page 2 HL02UrevD,10/97 MECHANICAL Package/Pinout "Y" and "Z" 1.285±0.010" (32.64±0.25) 1514 13 1.285±0.010" (32.64±0.25) 2423 22 2423 22 1514 13 TOP VIEWS 0.525±0.010" (13.34±0.25) 0.525±0.010" (13.34±0.25) HL02UxxyzzY HL02UxxyzzZ 0.695±0.015" (17.65±0.38) 123 10 11 12 123 10 11 12 0.375±0.005" (9.52±0.13) 0.015±0.005" (0.38±0.13) 0.020±0.002" (0.51±0.05) SIDE VIEWS 0.375±0.005" (9.52±0.13) 0.015±0.005" (0.38±0.13) 0.100±0.010" (2.54±0.25) 0.020±0.002" (0.51±0.05) 0.100±0.010" (2.54±0.25) END VIEWS 0°-15° 0.600" (15.24) 0.125+0.030" -0.000" (3.18+0.76) ( -0.00) 0.014±0.002" (0.36±0.05) .015±.010" (.38±.25) DIP PACKAGE NU = Do Not Use. NC = No Internal Connection. Duplicate pin functions are internally connected. All dimensions are in inches (millimeters). GRID: 0.100 inches (2.54 millimeters) Typically Marked with: specific model ordered, date code, job code and Logo. SMD PACKAGE PIN CONNECTIONS PIN# 1 2 3 10 11 12 13 14 15 22 23 24 SINGLES +VIN NU NU -VOUT +VOUT -VIN -VIN +VOUT -VOUT NU NU +VIN DUALS +VIN -VOUT Common Common +VOUT -VIN -VIN +VOUT Common Common -VOUT +VIN RECOMMENDED LAND PATTERN 0.100" (2.54) 2423 22 1514 13 RECOMMENDED REFLOW PROFILE 30 sec MAX (>220°C) 250 235 °C MAX 220 200 190 TEMPERATURE (°C) 0.730" (18.54) 0.040" (1.02) 123 0.080" (2.03) 150 10 11 12 100 1.150" (29.21) 90 sec MAX (>190°C) 50 TIME (seconds) HL02UrevD,10/97 Page 3 TYPICAL PERFORMANCE CURVES 250 LOAD CAPACITANCE vs INPUT RISE TIME (All 5 Vout Models) 75 LOAD CAPACITANCE vs INPUT RISE TIME (All 12 Vout Models) Capacitance (µF) Capacitance (µF) 200 150 100 50 0 0 5 10 (mS) 15 20 SAFE OPERATING AREA 60 45 30 15 0 0 5 10 (mS) 15 20 SAFE OPERATING AREA LOAD CAPACITANCE vs INPUT RISE TIME (All 15 Vout Models) 50 100% EFFICIENCY vs LOAD Capacitance (µF) 40 30 20 10 0 0 5 10 (mS) VOUT vs LOAD (All Models Normalized) 15 20 SAFE OPERATING AREA Efficiency 50% 10% 0% 25% 50% Load 75% 100% NOTES: 1.) When operated within the SAFE OPERATING AREA as defined by the above curves, the output voltage of HL02U devices is guaranteed to be within 95% of its steady-state value within 100 milliseconds after the input voltage has reached 95% of its steadystate value. 2.) For dual output models, total load capacitance is the sum of the capacitances on the plus and minus outputs. 110% Vout 100% 90% 25% 50% 75% Load 100% 125% Page 4 HL02UrevD,10/97